Interclene 5012

Interclene 5012
Tin Free Antifouling

PRODUCT DESCRIPTION
Low VOC, High Solids, TBT free copolymer antifouling applicable under water condition.
Capable of being applied and cured in water.
Fast drying and good application property in water.
INTENDED USES
A TBT free antifouling paint designed to apply by diver with rubber scraper, steel scraper or hand in water to repair
the mechanically damaged areas.
PRODUCT INFORMATION
Colour
BCA512-Red
Finish/Sheen
Not applicable
Part B (Curing Agent)
Not applicable
Volume Solids
70% 2% (ISO 3233:1998)
Mix Ratio
Not applicable
Typical Film Thickness
250 microns dry (357 microns wet)
Theoretical Coverage
2.80 m/litre at 250 microns dft, allow appropriate loss factors
Method of Application
Hand Applicator
Mechanical Applicator
Flash Point (Typical)
Single Pack 31C
Induction Period
Not applicable
Drying Information
5C
10C
25C
35C
Touch Dry [ISO 9117/3:2010]
1 hrs
40 mins
30 mins
20 mins
5C
10C
Overcoating Data - see limitations
Overcoated By
Note
REGULATORY DATA
VOC
Substrate Temperature
Min
Max
Min
25C
Max
Min
35C
Max
Min
Max
Consult your International Paint representative for the system best coating
240g/lt as supplied (Calculated)
Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation
depending on factors such as differences in colour and normal manufacturing tolerances.
Marine Coatings
Page 1 of 4
Issue Date:22/08/2016
Ref:4013
Interclene 5012
CERTIFICATION
When used as part of an approved scheme, this material has the following certification:
Product recognised by the following classification societies as compliant with the International Convention on the
Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001):
Korean Register of Shipping
Det Norske Veritas
Lloyds Register
Consult your International Paint representative for details.
SYSTEMS AND
COMPATIBILITY
Consult your International Paint representative for the system best suited for the surfaces to be protected.
SURFACE PREPARATIONS
Use in accordance with the standard Worldwide Marine Specifications.

All surfaces to be coated must be clean, dry and free from contamination.
Underwater application: Surface treatment by mechanical equipment or stainless sponge should be required in order
to remove marine growth such as slime and any contamination (salt deposit).
NEWBUILDING/MAJOR REFURBISHMENT/REPAIR
Consult your International Paint representative for specific recommendations.
Marine Coatings
Page 2 of 4
Ref:4013
Interclene 5012
APPLICATION
Rubber Scraper
Recommend use of Rubber scraper after application by hand.
Steel Scraper
Recommend use of Steel scraper after application by hand.
Mixing
This material is a one pack coating and should always be mixed thoroughly with a power agitator before
application.
Thinner
Not recommended.
Airless Spray
Not recommended.
Conventional Spray
Not recommended.
Brush
Not recommended.
Roller
Not recommended.
Cleaner
International GTA007
Work Stoppages and Cleanup All unused material should be stored in tightly closed containers. Partially filled containers may show surface
skinning and/or a viscocity increase of the material after storage.

Paint contacted with water should be thrown away after work.
SAFETY
All work involving the application and use of this product should be performed in compliance with all
relevant national Health, Safety & Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health
and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and
container labels. If you do not fully understand these warnings and instructions or if you can not strictly
comply with them, do not use this product. Proper ventilation and protective measures must be provided
during application and drying to keep solvent vapour concentrations within safe limits and to protect
against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves,
goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods
and work environment.
EMERGENCY CONTACT NUMBERS:
USA/Canada - Medical Advisory Number 1-800-854-6813
Europe - Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191
R.O.W. - Contact Regional Office
Marine Coatings
Page 3 of 4
Ref:4013
Interclene 5012
LIMITATIONS
UNIT SIZE
Where necessary, surface should be cleaned prior to overcoating, to ensure removal of any surface contamination,
foulants those have accumulated.
Application should be carried out by hand with pressure in the water, and then get flat coated surface by hand,
rubber scaper or steel scraper.
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate
and environmental conditions. Consult your local International Paint representative for specific recommendations.
Unmixed material (in closed containers) should be maintained in protected storage in accordance with information
given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of
establishing a general guideline of the coating application procedures. Test performance results were obtained in a
controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or
any other tests, accurately represent results found in all field environments. As application, environmental and design
factors can vary significantly, due care should be exercised in the selection, verification of performance and use of
the coating.
Unit Size
5 lt
UNIT SHIPPING WEIGHT

(TYPICAL)
STORAGE
Vol
Pack
4 lt
5 lt
Unit Size
Unit Weight
5 lt
7.6 Kg
Shelf Life
6 months minimum at 25C. Subject to reinspection thereafter. Store in dry, shaded conditions
away from sources of heat and ignition.
WORLDWIDE AVAILABILITY Consult International Paint.

IMPORTANT NOTE
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically
recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at
their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but
we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless
we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent
permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by
operation of law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied
and technical advice given are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information
contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's
responsibility to check with their local representative that this data sheet is current prior to using the product.
This Technical Data Sheet is available on our website at www.international-marine.com or www.international-pc.com, and should be the same as this
document. Should there be any discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the
version on the website will take precedence.
All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies.
AkzoNobel, 2016
www.international-marine.com
Marine Coatings
Page 4 of 4
Ref:4013

Interclene 5012

Uploaded by

Copyright:

Available Formats

Interclene 5012

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Interclene 5012

Uploaded by

Copyright:

Available Formats

Interclene 5012

Tin Free Antifouling

Part B (Curing Agent)

70% 2% (ISO 3233:1998)

Typical Film Thickness

250 microns dry (357 microns wet)

2.80 m/litre at 250 microns dft, allow appropriate loss factors

Flash Point (Typical)

Single Pack 31C

Touch Dry [ISO 9117/3:2010]

Overcoating Data - see limitations

240g/lt as supplied (Calculated)

Use in accordance with the standard Worldwide Marine Specifications.

skinning and/or a viscocity increase of the material after storage.

UNIT SHIPPING WEIGHT

WORLDWIDE AVAILABILITY Consult International Paint.

You might also like