Siemens MXL IQ Operation Installation Manual

Technical Manuals Online! - http://www.tech-man.
com
Cerberus Division
Table of Contents
Version 1.0
This CD-Rom contains

the information necessary to
install, operate and maintain
the Siemens, Cerberus Division
MXL/MXLV and MXL-IQ
Fire Protection Control Panels
Contents
MXL/MXLV Control Panel

P/N 315-092036CD-8
Personalize/
Printout Cover
MXL-IQ Control Panel

P/N 315-093624CD-9
Personalize/
Printout Cover
Navigation
There are three ways to navigate:
1) Use the left hand index column (which appears as you proceed)
2) Use the green buttons above to get to the corresponding manual
3) Use the arrows in the menu bar above
There are 2 ways to enlarge or reduce:
1) Use the magnifying glass in the menu bar above
2) Use the three different page views in the menu bar.
Cerberus Division
CERBERUS PYROTRONICS
MXL-IQ CONTROL PANEL

Operation, Installation, and Maintenance Manual
Siemens Building Technologies, Inc.

8 Fernwood Road
Florham Park, New Jersey 07932
P/N 315-093624CD-9
Technical Manuals Online! - http://www.tech-man.com
Siemens Building Technologies, Ltd.

50 East Pearce Street
Richmond Hill, Ontario L4B 1B7 CN
CAUTION
ALL WIRING MUST BE DONE AS DESCRIBED BELOW
TO OBTAIN SAFE AND PROPER SYSTEM OPERATION.
1. Earth ground the MXL-IQ enclosure properly; see the latest edition of the National
Electrical Code for approved methods. Conduit ground is NOT adequate.
2. Separate all wiring for initiating devices (i.e., detectors, manual stations, TRI
modules, etc.) from all other wiring in the MXL-IQ enclosure. To wire the System in compliance with UL 864, refer to the Installation and Power Limited
Wiring Instructions for the MSE-3L Enclosure, P/N 315-095445.
3. INSULATE ALL CABLE DRAIN WIRES from any conduit or earth grounded
electrical box, including those in the MXL-IQ enclosure.
4. Connect shield cable drain wire ONLY inside the MXL-IQ enclosure.
5. No wiring used for any of the following can run outside the building:
an ALD loop
a RS-485 network
an NAC circuit used for audibles
a CZM-1B6 or CZM-4 initiating device loop
For additional wiring information, refer to this manual or call Siemens
Building Technologies, Inc. Technical Support Department at
1-800-248-7976.
Table of Contents
Description ______________________________ 1 - 1
Chapter 1
Introduction ___________________________________________________ 1 - 1
Software ______________________________________________________ 1 - 1
Minimum MXL-IQ Control Panel Configuration ________________________ 1 - 3
Components Of The Basic System __________________________________ 1 - 4

SMB-2 Main Board _____________________________________________ 1 - 4
MPS-6 Power Supply ___________________________________________ 1 - 5
MPS-12 Power Supply __________________________________________ 1 - 5
MKB-4 Keyboard/Annunciator Panel _______________________________ 1 - 5
PIM-1 Peripheral Interface Module _________________________________ 1 - 6
PIM-2 Peripheral Interface Module _________________________________ 1 - 6
PAL-1 _______________________________________________________ 1 - 6
TSW-2 Tamper Switch __________________________________________ 1 - 6
BP-61 Batteries ________________________________________________ 1 - 7
BTX Batteries _________________________________________________ 1 - 7
Optional Modules _______________________________________________ 1 - 7

MOM-2 Card Cage _____________________________________________ 1 - 8
MOM-4 Card Cage _____________________________________________ 1 - 8
CSM-4 Signal Module ___________________________________________ 1 - 8
CMI-300 Interface Module________________________________________ 1 - 9
CRM-4 Relay Module ___________________________________________ 1 - 9
CZM-4 Conventional Zone Module _________________________________ 1 - 9
ALD-2I Analog Loop Driver ______________________________________ 1 - 10
MOI-7 Voice and Annunciator Driver_______________________________ 1 - 10
MOD-16 Output Driver _________________________________________ 1 - 10
MID-16 Input Driver ____________________________________________ 1 - 11
NIM-1R Network Interface Module ________________________________ 1 - 11
Table of Contents
Intelligent/Analog Devices _______________________________________ 1 - 12

FP Intelligent Detector Series ____________________________________ 1 - 12
ICP Intelligent Control Point _____________________________________ 1 - 12
ICP-B6 Intelligent Control Point __________________________________ 1 - 12
ID Intelligent/Analog Detector Series ______________________________ 1 - 12
IL Intelligent/Analog Detector Series _______________________________ 1 - 13
LIM-1 Loop Isolator Module _____________________________________ 1 - 14
MSI Intelligent Manual Station Series ______________________________ 1 - 14
TRI Intelligent Interface Module Series _____________________________ 1 - 14
CZM-1B6 Remote Conventional Zone Module _______________________ 1 - 14
Conventional Devices ___________________________________________ 1 - 15

DI Ionization Detector Series ____________________________________ 1 - 15
DT-11 Thermal Detector ________________________________________ 1 - 15
PE Photoelectric Detector Series _________________________________ 1 - 15
PBA-1191 Linear Beam Smoke Detector ___________________________ 1 - 15
Chapter 2
Installation ______________________________ 2 - 1
General Guidelines For Installing The MXL-IQ ________________________ 2 - 1
Installation Instructions For The MXL-IQ Control Panel __________________ 2 - 2

Install the MSE-3L Enclosure _____________________________________ 2 - 2
Install The TSW-2 Tamper Switch _________________________________ 2 - 2
Pull All Field Wiring Into The Backbox ______________________________ 2 - 3
Install the SMB-2 _______________________________________________ 2 - 3
Install the MPS-6/12 ____________________________________________ 2 - 3
Install the MKB-4 Keyboard/Annunciator ____________________________ 2 - 4
Install the PIM-1, PIM-2, and PAL-1 ________________________________ 2 - 5
Install the MOM-2 or MOM-4 ______________________________________ 2 - 6
Install the MOI-7, MOD-16, and MID-16 ____________________________ 2 - 9
Install Field Wiring _____________________________________________ 2 - 10
Check Field Wiring ____________________________________________ 2 - 10
ii
Table of Contents
Start Up Procedure ____________________________________________ 2 - 10

System Function Checkout ______________________________________ 2 - 16
Operation _______________________________ 3 - 1
Chapter 3
Introduction ___________________________________________________ 3 - 1
Addresses ____________________________________________________ 3 - 1
System Modules _______________________________________________ 3 - 2
Remote System Modules ________________________________________ 3 - 2
Using The MKB-4 Keyboard/Annunciator Panel In Local Mode ____________ 3 - 3

The Display ___________________________________________________ 3 - 3
Internal Audible Alarm ___________________________________________ 3 - 4
Modes Of Operation ____________________________________________ 3 - 5
Alarm ________________________________________________________ 3 - 6
How The System Annunciates Fire Alarms __________________________ 3 - 6
Viewing the List of Alarms ________________________________________ 3 - 7
How to Block Acknowledge A Fire Alarm ____________________________ 3 - 7
How to Individually Acknowledge A Fire Alarm ________________________ 3 - 7
Silencing The System ___________________________________________ 3 - 7
Supervisories __________________________________________________ 3 - 8
How The System Annunciates Supervisories _________________________ 3 - 8
Viewing the List of Supervisories __________________________________ 3 - 8
How to Block Acknowledge a Supervisory ___________________________ 3 - 8
How to Individually Acknowledge a Supervisory _______________________ 3 - 9
Troubles ______________________________________________________ 3 - 9
How The System Annunciates Troubles _____________________________ 3 - 9
Viewing The List of Troubles ______________________________________ 3 - 9
How to Block Acknowledge a Trouble______________________________ 3 - 10
How to Individually Acknowledge a Trouble _________________________ 3 - 10
iii
Table of Contents
Security Conditions_____________________________________________ 3 - 10
How The System Annunciates Security Conditions ___________________ 3 - 10
Viewing the List of Security Conditions _____________________________ 3 - 11
How to Individually Acknowledge a Security Condition _________________ 3 - 11
Reset Procedures ______________________________________________ 3 - 11

Hard Reset __________________________________________________ 3 - 11
Soft Reset ___________________________________________________ 3 - 11
Using The MKB Keyboard/Annunciator Panel in Global Mode ____________ 3 - 12

Limitations/Restrictions _________________________________________ 3 - 12
Global MKB Display Format _____________________________________ 3 - 12
Global Keypad Operation _______________________________________ 3 - 13
Using The Menu _______________________________________________ 3 - 14

Operation of the Keys on the MXL-IQ Annunciator Panel ______________ 3 - 14
Numeric Keypad ______________________________________________ 3 - 14
The Command Keypad _________________________________________ 3 - 14
Overview of the Menus Structure _________________________________ 3 - 15
Beginning a Menu Session ______________________________________ 3 - 16
Introduction to the Acknowledge Menu _____________________________ 3 - 16
Introduction to the List Menu _____________________________________ 3 - 16
Introduction to the Control Menu __________________________________ 3 - 16
Introduction to the Test Menu ____________________________________ 3 - 16
Entering Your Password ________________________________________ 3 - 17
Entering a Module Number and Device Number _____________________ 3 - 17
Entering a Device Number with the Module Number __________________ 3 - 17
ACKNOWLEDGE Menu __________________________________________ 3 - 18

Entering the Acknowledge Menu _________________________________ 3 - 18
Acknowledge Alarm ___________________________________________ 3 - 18
Acknowledge Supervisory _______________________________________ 3 - 19
Acknowledge Trouble __________________________________________ 3 - 20
Acknowledge Security __________________________________________ 3 - 21
iv
Table of Contents
LIST Menu ____________________________________________________ 3 - 22

Entering the List Menu _________________________________________ 3 - 22
List Status ___________________________________________________ 3 - 23
List Alarm ___________________________________________________ 3 - 23
List Supervisory _______________________________________________ 3 - 24
List Trouble __________________________________________________ 3 - 24
List Security Conditions _________________________________________ 3 - 25
List Sensitivity Settings _________________________________________ 3 - 26
List Voltages _________________________________________________ 3 - 26
List Temp ____________________________________________________ 3 - 28
List Module Type ______________________________________________ 3 - 28
List Device Type ______________________________________________ 3 - 29
List Message _________________________________________________ 3 - 29
List Software Version __________________________________________ 3 - 30
List Output States _____________________________________________ 3 - 31
List Device Usages ____________________________________________ 3 - 31
List Node Address _____________________________________________ 3 - 32
List ANALASER ______________________________________________ 3 - 32
List ANALASER SMOKE_LEV __________________________________ 3 - 32
List ANALASER FLOW_LEV ___________________________________ 3 - 33
List ANALASER TRIP_PTS ____________________________________ 3 - 33
List Percent/ft ________________________________________________ 3 - 34
List Percent/ft Senstvty _______________________________________ 3 - 35
List Percent/ft Pre-alarm ______________________________________ 3 - 35
List Percent/ft Analog _________________________________________ 3 - 35
List ASD_apps _______________________________________________ 3 - 35
CONTROL Menu _______________________________________________ 3 - 36

Entering the Control Menu ______________________________________ 3 - 37
Control Reset ________________________________________________ 3 - 37
Control Sensitivity _____________________________________________ 3 - 37
Control Arm/dis _______________________________________________ 3 - 38
Table of Contents
Control Output on/off ___________________________________________ 3 - 38

Control Loop Arm _____________________________________________ 3 - 39
Control Loop Disarm ___________________________________________ 3 - 39
Control Net Link Request _______________________________________ 3 - 40
Control ANALASER ___________________________________________ 3 - 40
Control Percent/ft _____________________________________________ 3 - 41
Control Percent/ft - Senstvty _____________________________________ 3 - 41
Control Percent/ft - Pre-alarm ____________________________________ 3 - 41
Control Change Apps __________________________________________ 3 - 42
TEST Menu ___________________________________________________ 3 - 42

Entering the Test Menu _________________________________________ 3 - 43
Test Set Time ________________________________________________ 3 - 43
Test Ground Fault _____________________________________________ 3 - 44
Test Power __________________________________________________ 3 - 44
Lamp Test ___________________________________________________ 3 - 45
Test Device LED ______________________________________________ 3 - 45
Test MOI Lamp Test ___________________________________________ 3 - 46
Test Network (X-Network, M-Network) _____________________________ 3 - 46
Test Override _________________________________________________ 3 - 46
Detector Cleaning _____________________________________________ 3 - 47
Event Log ___________________________________________________ 3 - 47
Test Pre-alarm ________________________________________________ 3 - 47
Test ASD Devices _____________________________________________ 3 - 48
Test Summarize ______________________________________________ 3 - 48
Test Manual Activate ___________________________________________ 3 - 49
Chapter 4
Testing and Troubleshooting _________________ 4 - 1

System Test ____________________________________________________ 4 - 1
Every Six Months ______________________________________________ 4 - 1
Every Year ____________________________________________________ 4 - 1
Fuse Replacement _____________________________________________ 4 - 1
Troubleshooting _______________________________________________ 4 - 2
vi
Table of Contents
Walktest Operating Instructions______________ 5 - 1
Chapter 5
Introduction ___________________________________________________ 5 - 1
System w/AUD ________________________________________________ 5 - 2
System SIL ___________________________________________________ 5 - 2
Loop w/AUD __________________________________________________ 5 - 2
Loop SIL _____________________________________________________ 5 - 2
Zone wAUD ___________________________________________________ 5 - 2
Zone SIL _____________________________________________________ 5 - 2
Cancel _______________________________________________________ 5 - 2
Extend _______________________________________________________ 5 - 2
Suggested Walktest Proedure _____________________________________ 5 - 2

Walktest the System ____________________________________________ 5 - 3
Walktest Ending Sequence _______________________________________ 5 - 4
Walktest Entire ALD Loop, MOI-7 (MID-16), or CZM-4 Module ___________ 5 - 4
Walktest Ending Sequence _______________________________________ 5 - 5
Walktest Individual CZM-1B6 or CZM-4 Zone ________________________ 5 - 5
History Log ______________________________ 6 - 1
Chapter 6
CSG-M History Options__________________________________________ 6 - 1
Logging Methods _______________________________________________ 6 - 2

Enabling the History Option in CSG-M ______________________________ 6 - 4
From the MKB Menu ____________________________________________ 6 - 4
Local History Log Query _________________________________________ 6 - 5
Query Selection ________________________________________________ 6 - 5
Query Filters __________________________________________________ 6 - 5
Navigating The History Display ____________________________________ 6 - 6
History Display Formats _________________________________________ 6 - 6
Device Event __________________________________________________ 6 - 6
Reset Event ___________________________________________________ 6 - 6
Set Time Event ________________________________________________ 6 - 7
Block Acknowledge Event ________________________________________ 6 - 7
vii
Table of Contents
Audible Silenced Event __________________________________________ 6 - 8

Override Event ________________________________________________ 6 - 8
Audible Unsilenced Event ________________________________________ 6 - 8
Password Event _______________________________________________ 6 - 8
Configuration Changed Event _____________________________________ 6 - 9
Manual Sensitivity Set Event ______________________________________ 6 - 9
Auto Sensitivity Set Event ________________________________________ 6 - 9
Logic Sensitivity Set Event ______________________________________ 6 - 10
History Print Formats At The MXL-IQ Panel _________________________ 6 - 10
MXL-IQ To CSG-M Download Formats _____________________________ 6 - 13
History Download Sequence _____________________________________ 6 - 14
Chapter 7
Connections and Ratings ___________________ 7 - 1

ALD-2I ________________________________________________________ 7 - 1
CMI-300 _______________________________________________________ 7 - 3
CRM-4 ________________________________________________________ 7 - 5
CSM-4 ________________________________________________________ 7 - 7
CZM-1B6 _____________________________________________________ 7 - 13
CZM-4 _______________________________________________________ 7 - 17
MOI-7, MOD-16, MID-16 __________________________________________ 7 - 19
MOM-2 ______________________________________________________ 7 - 25
MOM-4 ______________________________________________________ 7 - 27
NIM-1R ______________________________________________________ 7 - 29
Silent Knight Model 5128/5129 ____________________________________ 7 - 33
SMB-2 _______________________________________________________ 7 - 35
viii
Table of Contents
Compatible Devices _____________________________________________ A - 1
Appendix
Device Analog Voltages __________________________________________ B - 1

MXL-IQ Battery Calculations _______________________________________ C - 1
MXL-IQ Power Supply Load Calculations _____________________________ D - 1
Alarm Verification _______________________________________________ E - 1
Envirolink _____________________________________________________ F - 1
Latching/Non-Latching Troubles ____________________________________ G - 1
Installing A Security Point ________________________________________ H - 1
Application Specific Detection (ASD) ________________________________I - 1
MXL-IQ Trouble Messages _________________________________________ J - 1
Power Limited Wiring ____________________________________________ K - 1
New Two Stage Alarm ___________________________________________ L - 1
Pre-alarm, Dual Criteria Logic Functions, and Percent Per Foot
Obscuration Features ___________________________________________ M - 1
MXL-IQ Spare Parts List __________________________________________ N - 1
New Features for MXL-IQ Revision 6.0 and Higher ______________________ O - 1
ix
Table of Contents
+D=FJAH
Description
The CERBERUS PYROTRONICS MXL-IQ
Control Panel is an advanced fire protection
and alarm control panel that provides superior
fire protection and multiplexed alarm reporting.
The MXL-IQ Control Panel can monitor up
to 4 analog loops, each containing up to 60
CERBERUS PYROTRONICS intelligent
devices.
The MXL-IQ Control Panel can control a
wide variety of System outputs, such as:
Conventional Form C relay contacts
Solid State outputs
Supervised outputs to control Alarm
Notification Appliances
Municipal Tie outputs
Leased Line outputs
The MXL-IQ Control Panel can process
logical decisions based on the status of
initiating devices. The System can respond
with customer-specified sequences of
output circuit operation.
The System continuously checks all
software and hardware for proper operation. It continuously checks all System
memory components, control panel electronic hardware, and the System program.
A hardwire watchdog circuit is provided to
ensure that System programs are functioning properly. If a problem develops with the
program or processor, the watchdog circuit
places the System into a trouble condition
and resets it.
To ensure reliable operation, the MXL-IQ

System is composed of independent
modules, each with its own microprocessor.
If the main panels central processing unit
stops, these modules, operating in default,
still annunciate any alarm or trouble
through common lines called Any Alarm
and Any Trouble. All of the modules
communicate with the MXL-IQ Panel
through a serial communications System.
INTRODUCTION
All modules are continuously supervised for

their presence and for proper operation.
Problems are shown on the display to aid in
servicing and troubleshooting (See Using
the Menu in the OPERATIONS section).
The MXL-IQ System is designed so that fire
alarm operation has first priority over all
other modes of operation. If the System
loses battery and commercial power, it
automatically goes through an initialization
routine when power returns.
The MXL-IQ software was written in a highlevel language for ease of maintenance.
The software incorporates a multitasking
operating system that allows the microprocessor to handle many tasks almost
simultaneously. This enables the MXL-IQ
System to handle communications to all
initiating and output option boards and to
the annunciator. This also enables the
MXL-IQ System to check that everything is
running.
SOFTWARE
1-1
Description
ALARM
POWER
AUDIBLE
SILENCE
PARTIAL
SYSTEM
DISABLE
SUPERVISORY
DISPLAY
TROUBLE
NEXT
HOLD
SECURITY
MXL-IQ
Exterior View
Interior View
Figure 1
The MXL-IQ Control Panel
1-2
Description
When the MXL-IQ Control Panel receives
power, the System runs a start-up procedure that sets up all initial conditions. The
System then starts the operating system
and the initialization routines for all of the
tasks, most of which concern handling
System modules. When the display task is
finished initializing, it displays the default
time and date at power-up. Initialization of
other modules may take several seconds,
but this takes place in the background and
so does not affect System operation.
fied modules. Any modules or devices that

do not agree with the programmed data are
reported as troubles on the annunciator.
Minimum MXL-IQ Control Panel

Configuration To Meet NFPA 72 Local,
Municipal Tie, Remote Station,
Proprietary, And Central Station,
UL 1076, And NFPA 12A, 13, And 2001
Table 1 presents the minimum configuration necessary to meet NFPA 72 Local,

Municipal Tie, Remote Station, Proprietary,
and Central Station, UL 1076, and NFPA
12A, NFPA 13 and NFPA 2001.
The MXL-IQ System polls all network

addresses to see that all specified modules
are present and that there are no unspeci-
NFPA Minimum Quantity

Module
Description
72
Local
72
Auxiliary
72
Remote
Station
72
Proprietary
72 Central
Station(a)
UL
1076(b,d)
12A,
13, or 20 01
SMB-2(c)
MXL-IQ Main Unit
1*
1*
1*
MPS-6/12
Power Supply
MKB-4
Keyboard/Annunciator Panel
MOM-2
Optional Module Card Cage
MOM-4
Optional Module Card Cage
1 or 2**
1(h)
***
***
***
***
***
***
CSM-4
Signal Module
CZM-4
Conventional Zone Module
ALD-2I
Analog Loop Driver
***
***
***
***
***
****
***
CZM-1B6
Remote Conventional Zone Module
***
***
***
***
***
***
-----------
Batteries(e,f)
1(e)
1(e)
1(e)
1(e)
1(d)
1(e)
TSW-2
Tamper Switch
1(d)
PIM-1
Peripheral Interface Module
PIM-2
Peripheral Interface Module
PAL-1
Logging Printer
NET-7
Communication Interface
MOI-7
Voice and Annunciator Driver
MOD-16
Output Driver
MID-16
Input Module
CRM-4
Relay Module
CMI-30 0
MXL/CXL Interface
X = not required
*
**
Use Silent Knight listed models 5128/5129 and 5230.

One CSM-4 circuit must be configured for alarm
transmission. In addition, depending on the local authority
having jurisdiction, additional circuits may be required for
Supervisory or Trouble transmission.
*** Any one of these modules is sufficient as an initiating
device.
**** Only TRI-60/B6, TRI-60R/B6R, and TRI-60D/B6D can be
used as security devices.
NOTES:
a. See pages 7-33 to 7-34 for NFPA 72 Central Station.
b. Refer to the MXL-IQ Wiring Diagram, P/N 575-293638 at the end of the manual.
c. The SMB-2 must be programmed by CSG-M for all System configurations (See CSG-M
Programming Manual, P/N 315-090381).
d. UL 1076 requires a Model TSW-2 tamper switch and a PAL-1 printer.
e. The batteries available are: BP-61, BTX-1, and BTX-2. The BP-61 is a module consisting of four
6V, 15 AH batteries. The BTX-1 batteries are a pair of 12V, 31 AH batteries. The BTX-2 batteries
are a pair of 12V, 55 AH batteries. Actual battery size depends on System configuration.
f. See Appendix C for Battery Calculations.
g. The CMI-300 is not listed for UL 1076 application.
h. Refer to the CSM-4 Installation Instructions (P/N 315-090854) for programming.
TABLE 1
Minimum MXL-IQ Configuration to Meet NFPA 72 Local, Auxiliary, Remote Station, Proprietary, and Central
Station Connections, UL 1076, and NFPA 12A, NFPA 13, and NFPA 2001
1-3
Description
Components Of The Basic

System
The basic MXL-IQ Control Panel consists
of the following components:
SMB-2 Main Board
MPS-6 or MPS-12 Power Supply
MKB-4 Keyboard/Annunciator
PAL-1 Logging Printer
(NFPA Proprietary and UL 1076 configurations)
PIM-1 Peripheral Interface Module
MSE-3L Enclosure
TSW-2 Tamper Switch
(UL 1076 configuration only)
BP-61, BTX-1, or BTX-2 Batteries
P1
BATTERY
F2
20A
P14
MPS-6
CB1
NAC1
CB2
NAC2
MPS-12
P2
BATTERY
F3
F4
MOM-4
15 AMP
P3
POWER TO MOM-4
2 AMP MAX.
F1
MPS-6
8 AMP
P8
NAC 2
P13
NAC 1
16-bit central processing unit (CPU)

NOT
USED
System read-only memories (EPROMs)

System random-access memory (RAM)
FLASH memory for CSG-M
3
2
1
Watchdog circuitry
Network interface circuitry
DO NOT USE
MNET
TB1
S7
S4
1
D2300CP
PROGRAMMER
P4
PRINTER
P6
1
P5
I
C
1
1
4
I
C
1
1
3
I
C
1
1
2
I
C
1
1
1
I
C
1
1
0
P15
P10
TO ANN-1
GND FAULT
DISCONNECT
12A TO MOM-4
6
4
LOOP 1
7
5
TB2
10
8
4
3
11
9
SMB-2
LOOP 2
CZM-1B6
POWER
TB3
The SMB-2 Main Board contains:
12
4
3
SMB-2 Main Board
CZM-1B6 POWER
2 AMP
TRBL
4
OFF
1
ON
P17
ALR
24V regulator
2
1
MOM-4
Battery charger
AC transfer relay
CZM-1B6 auxiliary power
Figure 2
SMB-2 Main Board
24 VDC unregulated supply

Two analog loops (initiating/control)
Two notification appliance circuits
(audible circuits)
Two dry-contact relays (Form C)
1-4
Description
MPS-6 Power Supply

The MPS-6 is a supervised power supply
that converts 120 VAC, 60 Hz to unregulated 24 VDC at 6A.
MPS-12 Power Supply

The MPS-12 is a high current power supply
that provides the MXL-IQ System with
primary 24 VDC power. It is rated at 12
amps and is unfiltered and unregulated.
The MPS-12 supplies the SMB-2 with the
power required for normal operation. The
module incorporates a 5 amp resettable circuit
breaker on the primary input, a 15 amp fuse
on the 24V output, and a built-in AC line filter
for surge and noise suppression.
Figure 3A
MPS-6 Power Supply
Figure 3B
MPS-12 Power Supply
MKB-4 Keyboard/Annunciator Panel

The MKB-4 Annunciator communicates with
the SMB-2 Main Control Board through the
System network link. This module provides
the MXL-IQ with its primary control and
annunciation.
The MKB-4 module has an 80-character,
backlit LCD alphanumeric display that
continuously updates information about the
System status and user-defined device
messages. If there are multiple alarms,
and/or troubles, including supervisories and
security conditions, the MKB-4 displays the
highest priority event that occurred. The
user can see additional alarm and trouble
data by pressing the NEXT key. Press the
HOLD key at any time to stop the display
from scrolling.
The Control Panel contains the following
indicators:
Figure 4
MKB-4 Keyboard
The MKB-4 has switches for the following functions:
Alarm
Acknowledging fire alarms (ALARM ACK)
Power
Silencing audibles (AUD SIL)
Audible Silence
Acknowledging supervisories (SUPV ACK)
Partial System Disable
Acknowledging System troubles (TRBL ACK)
Supervisory
Acknowledging security conditions (SEC ACK)
Trouble
Resetting the Control Panel (RESET)
Security
In addition the module has display keys (NEXT and HOLD), a numerical keypad, PRINT, HELP, and CLEAR keys, and user-configurable
function keys.
1-5
Description

The PIM-1 module is an interface for an
MXL-IQ System to remote peripheral
devices such as printers. It connects an
RS-232C device to an MXL-IQ System
without the peripheral device's protective
ground causing a ground fault. The interface operates at up to 9600 baud without
losing any characters.

Figure 5
The PIM-2 module is an interface that

allows the connection of UL listed EDP
Centronics parallel printers to the MXL-IQ
System. It converts the RS-232C (serial)
printer output to a Centronics parallel
interface. When used with the PAL-1, the
PIM-2 provides a supervised parallel printer
(NFPA 72 Proprietary or UL 1076) for the
MXL-IQ System. However, this configuration is not supervised for data integrity.
PAL-1
The PAL-1 Logging Printer provides a
paper record of the activity of the MXL-IQ
System.
Figure 6
PAL-1 Parallel Printer
TSW-2 Tamper Switch

The TSW-2 Tamper Switch is a 3-position
switch that monitors the opening of the
MXL-IQ enclosure and reports a security
alarm. Closing the door automatically
returns the switch to its normal operating
position. The switch can be pulled out to
indicate a closed position for maintenance
purposes.
Figure 7
TSW-2 Tamper Switch
1-6
Description
BP-61 Batteries
The BP-61 is a module consisting of four 6V,
15 AH batteries. The BP-61 is recommended
for the NFPA 72 Local and Proprietary, and
the UL 1076 Systems. Actual battery size
depends on System configuration. See
Appendix C for battery calculations.
Figure 8
BP-61 Batteries
BTX Batteries
The BTX-1 batteries are a pair of 12V, 31
AH batteries. The BTX-2 batteries are a
pair of 12V, 55 AH batteries. Actual battery
size depends on System configuration. See
Appendix C for battery calculations.
Figure 9
BTX Batteries
The following modules are available as

options to the MXL-IQ Control Panel:
MOM-2 Card Cage
MOM-4 Card Cage
CSM-4 Signal Module
ALD-2I Analog Loop Driver

MOI-7 Voice and Annunciator Driver*
OPTIONAL
MODULES
MOD-16 Output Driver*

MID-16 Input Module*
NIM-1R Network Interface Module
CMI-300 Interface Module

CRM-4 Relay Module
CZM-4 Conventional Zone Module
* This module does not mount in the MSE-3L

enclosure.
1-7
Description
MOM-2 Card Cage

The MOM-2 Card Cage contains 2 slots for
optional module cards; it can handle 2 halfwidth cards or 1 full-width card. The MOM-2
provides 2 power-connector receptacles and
2 data-connector receptacles. A 24 VDC
cable that provides the main power used by
the optional modules, and an 8-wire ribbon
cable for connection of 5 VDC and data, are
provided with the MOM-2 installation kit.
Figure 10
MOM-2 Card Cage
MOM-4 Card Cage

The MOM-4 Card Cage contains 4 slots for
optional module cards; it can handle 4 halfwidth cards or 2 full-width cards. The MOM-4
provides 2 power-connector receptacles
and 2 data-connector receptacles. A 24 VDC
cable that provides the main power used by
the optional modules, and an 8-wire ribbon
cable for connection of 5 VDC and data, are
provided with the MOM-4 installation kit.
Figure 11
MOM-4 Card Cage
CSM-4 Signal Module

The CSM-4 Signal module controls 2
supervised notification appliance circuits.
Each circuit is capable of either Style Z
(Class A) or Style Y (Class B) operation.
Each circuit can be individually configured
for notification appliances, municipal tie,
leased line, or releasing service per NFPA
12A, NFPA 13, and NFPA 2001.
S1
S3
G1
S2
G2
S4
Figure 12
CSM-4 Signal Module
1-8
Description

The CMI-300 provides modem communications between an MXL-IQ System and a CXL
System. The CMI-300 module is located on
the MOM-2/4 board in the MXL-IQ enclosure. The CMI-300 plugs into a half slot in
the MOM-2/4. It translates signals from the
MXL-IQ communication lines of the SMB-2
to CXL modem signals. This signal is then
transmitted along suitable cable to the CXM-1
module in the CXL enclosure.
Figure 13
CRM-4 Relay Module

The CRM-4 Relay module is an output
control module that contains 4 relay outputs. Form C contacts are rated at 2A, 30
VDC/120 VAC resistive.
The CRM-4 has 4 LEDs. Two of the LEDs
are user programmable.
Figure 14
CRM-4 Relay Module

The CZM-4 Conventional Zone module
provides four initiating device circuits
capable of Style D (Class A) or Style B
(Class B) operation. Each zone has its own
address. You can use CSG-M to write a
custom message for each zone
(See CSGM Programming Manual,
P/N 315-090381).
Figure 15
1-9
Description

The ALD-2I Analog Loop Driver provides two
initiating device circuits capable of Class A
or Class B operation for monitoring analog
devices. Each loop is capable of monitoring
up to 60 analog devices. Each device has
its own address. You can use CSG-M to
write a custom message for each device
(See CSG-M Programming Manual, P/N
315-090381).
Figure 16
MOI-7 Voice and Annunciator Driver

The MOI-7 module is an MXL-IQ network
module that connects to a graphic annunciator using MOD-16s or MID-16s.
The MOI-7 has two LEDs to indicate the

status of the MXL-IQ network interface:
S1
the TRANSMIT LED blinks when the

MXL-IQ/MOI-7 communication is
working
the TROUBLE LED goes to steady
when MOI cannot communicate
Figure 17
MOD-16 Output Driver

The MOD-16 Output Driver module is an
annunciator driver controlled by the MOI-7
module. Up to 8 MOD-16s can be used with
an MOI-7. Each MOD-16 can activate up to
16 outputs for a total of 128 outputs.
Figure 18
MOD-16 Output Driver
1-10
Description
MID-16 Input Driver

The MID-16 module provides 16 general
purpose inputs for user-defined operations
for the MXL-IQ.
The MID-16 is controlled by the MOI-7
module. Up to 8 MID-16s can be used with
an MOI-7. The function of each individual
input is defined by the use assigned to it in
CSG-M.
Figure 19
MID-16 Input Driver

The NIM-1R provides a communication path
for the following uses:
as an MXL-IQ networking interface
as a connection to Foreign Systems
as a connection to AnaLASER detectors
When used as a networking interface the
NIM-1R supports the connection of up to 63
MXL-IQ Systems. This network also supports
a Network Command Center (NCC) that
monitors all the MXL-IQs in the networked
group.
Output logic between MXL-IQ panels is made
using CSG-M programming. CSG-M versions
6.01 and higher include options for networked
MXL-IQ systems. Each MXL-IQ System is
assigned a panel number. This panel
number allows interactive programming
between panels using CSG-M.
The NIM-1R supports Style 4/7 connection.
In the event of an NIM-1R communication
failure, each MXL-IQ System continues to
operate as a stand-alone panel.
Figure 20
The NIM-1R can also be configured as an

RS-232 or RS-485 two-wire interface to
foreign systems. This operation is called
FSI (Foreign System Interface). The FSI
responds to a protocol and gathers information about the MXL-IQ status. The interface
supports both single MXL-IQ Systems and
networked systems. Typical use of this
interface is between the MXL-IQ and
building management systems.
1-11
Description
The intelligent/analog devices described
below are available for use with the MXL-IQ
Control Panel (SMB-2).
The UL identifiers for compatibility are the
same as the model names specified below.
INTELLIGENT/
ANALOG DEVICES
FP-11 Intelligent/Analog Photoelectric

Detector
The FP-11 is an intelligent/analog photoelectric detector that can be used as an
area or duct detector [FP-11(d)]. It uses
either a DB-11 low profile mounting base or
DB-3S mounting base with the DB-ADPT
adapter, a DB-X11RS mounting base with
relay or DB-X3RS mounting base with relay
with the DB-ADPT adapter, an ADBI-60
audible base with the DB-ADPT adapter, or
an AD-11P or AD-11XPR air duct housing.
The FP-11 requires MXL-IQ Rev. 6.0 or
higher firmware.
FPT-11 Intelligent Thermal Detector

The FPT-11 is an intelligent/analog ratecompensated/fixed-temperature type
thermal and photoelectric detector. It can
only be used as an area detector. It uses
either a DB-11 low profile mounting base or
DB-3S mounting base with the DB-ADPT
adapter, a DB-X11RS mounting base with
relay or DB-X3RS mounting base with relay
with the DB-ADPT adapter, or an ADBI-60
audible base with the DB-ADPT adapter.
The FPT-11 requires MXL-IQ Rev. 6.0 or
higher firmware.
ICP Intelligent Control Point

The ICP is an intelligent control point that
can be used as an independent, remotely
located notification appliance circuit (NAC).
It communicates through the analog loop of
the MXL-IQ System.
ICP-B6 Intelligent Control Point

The ICP-B6 is an intelligent control point
that can be used as an independent,
remotely located notification appliance
circuit (NAC). It communicates through the
analog loop of the MXL-IQ System.
ID-60P Intelligent/Analog
Photoelectric Detector
The ID-60P is an intelligent/analog photoelectric detector that can be used as an area or
1-12
duct detector [ID-6OP(d)]. It uses either a

DB-3S low profile mounting base, a DB-X3RS
mounting base with relay, an AD-3P duct
housing, or an ADBI-60 audible base.
ID-60PT Intelligent/Analog Photoelectric Detector with Heat Sensor

The ID-60PT is an intelligent/analog ratecompensated/fixed-temperature type
either a DB-3S low profile mounting base, a
DB-X3RS mounting base with relay, or an
ADBI-60 audible base.
ID-60I Intelligent/Analog Ionization

Detector
The ID-60I is an intelligent/analog ionization
detector for use in open areas at altitudes
of 0 to 4000 feet. It uses either a DB-3S low
profile mounting base, a DB-X3RS mounting base with relay, or an ADBI-60 audible
base.
ID-60IH Intelligent/Analog Ionization

High Altitude Detector
The ID-60IH is an intelligent/analog ionization detector for use in open areas at
altitudes of 3000 to 8000 feet. It uses either
a DB-3S low profile mounting base, a
ID-60IA Intelligent/Analog Ionization

High Air-Velocity Detector
The ID-60IA is an intelligent/analog ionization high air-velocity detector for use in
open areas, computer facilities, and air
ducts at altitudes of 0 to 4000 feet. It uses
ID-60IAH Intelligent/Analog Ionization

High Air-Velocity, High Altitude
Detector
The ID-60IAH is an intelligent/analog
ionization high air-velocity, high altitude
detector for use in open areas, computer
facilities, and air ducts at altitudes of 3000 to
8000 feet. It uses either a DB-3S low profile
mounting base, a DB-X3RS mounting base
with relay, or an ADBI-60 audible base.
Description
ID-60IB Intelligent/Analog Ionization

Air-Duct Detector
ILI-1B Intelligent/Analog Ionization AirDuct Detector
The ID-60IB is an intelligent/analog ionization detector for use in air duct applications
at altitudes of 0 to 4000 feet. It uses either
the AD-3I housing or the AD-3XRI housing.
The ILI-1B is an intelligent/analog ionization

detector for use in air duct applications at
altitudes of 0 to 4000 feet. It uses either the
AD-3I housing or the AD-3XRI housing.
ID-60IBH Intelligent/Analog Ionization

Air-Duct High Altitude Detector
ILI-1BH Intelligent/Analog Ionization

Air-Duct High Altitude Detector
The ID-60IBH is an intelligent/analog

ionization detector for use in air duct
applications at altitudes of 3000 to 8000
feet. It uses either the AD-3I housing or the
AD-3XRI housing.
The ILI-1BH is an intelligent/analog ionization detector for use in air duct applications
at altitudes of 3000 to 8000 feet. It uses
either the AD-3I housing or the AD-3XRI
housing.
ILI-1 Intelligent/Analog Ionization

Detector
ILP-1 Intelligent/Analog Photoelectric

Detector
The ILI-1 is an intelligent/analog ionization

of 0 to 4000 feet. It uses either a DB-3S low
profile mounting base, a DB-X3RS mounting base with relay, or an ADBI-60 audible
base.
The ILP-1 is an intelligent/analog photoelectric detector that can be used as an

area or duct detector [ILP-1(d)]. It uses either
a DB-3S low profile mounting base, a
DB-X3RS mounting base with relay, an
AD-3ILP or AD-3XRILP duct housing, or an
ILI-1H Intelligent/Analog Ionization

The ILI-1H is an intelligent/analog ionization
of 3000 to 8000 feet. It uses either a DB-3S
low profile mounting base, a DB-X3RS
mounting base with relay, or an ADBI-60
audible base.
ILI-1A Intelligent/Analog Ionization

High Air-Velocity Detector
The ILI-1A is an intelligent/analog ionization
high air-velocity detector for use in open
areas, computer facilities, and air ducts at
altitudes of 0 to 4000 feet. It uses either a
DB-3S low profile mounting base, a
ILI-1AH Intelligent/Analog Ionization

High Air-Velocity, High Altitude
Detector
The ILI-1AH is an intelligent/analog ionization high air-velocity, high altitude detector
for use in open areas, computer facilities,
and air ducts at altitudes of 3000 to 8000
feet. It uses either a DB-3S low profile
ILPT-1 Intelligent/Analog Photoelectric

Detector with Heat Sensor
The ILPT-1 is an intelligent/analog ratecompensated/fixed-temperature type
ILP-2 Intelligent/Analog Photoelectric

Detector
The ILP-2 is an intelligent/analog photoelectric detector that can be used as an
area or duct detector [ILP-2(d)]. It uses
DB-X3RS mounting base with relay, an
AD-3ILP or AD-3XRILP duct housing, or an
ADBI-60 audible base. The ILP-2 requires
MXL-IQ Rev. 3.0 or higher firmware.
ILT-1 Intelligent Thermal Detector

The ILT-1 is an intelligent rate-compensated/fixed-temperature type thermal
detector. It uses either a DB-3S low profile
1-13
Description
LIM-1 Loop Isolator Module

The LIM-1 is a loop isolator module that
isolates short circuits on MXL-IQ analog
loops. The LIM-1 operates in both Class A
and Class B circuits.
MSI-10/20 Intelligent Manual Station

The MSI-10/20 is an intelligent manual
station designed to interface with an analog
loop. The MSI can be flush mounted or
surface mounted using the SB-5R mounting
box.
MSI-10B/20B Intelligent Manual Station

The MSI-10B/20B is an intelligent manual
loop. The MSI-10B/20B can be flush
mounted or surface mounted using the
SB-5R mounting box.
MSI-B6F Intelligent Manual Station

The MSI-B6F is an intelligent manual station
designed to interface with an analog loop.
The MSI-B6F is a single-action station;
when used with the MS-FD adapter, the
MSI-B6F is a double-action station. The
MSI-B6F can be flush mounted or surface
mounted using the MS-FB backbox.
MSI-MB6 Intelligent Manual Station

The MSI-MB6 is an intelligent manual
loop. The MSI-MB6 is a single-action
station; when used with the MS-DA plate,
the MSI-MB6 is a double-action station.
The MSI-MB6 can be flush mounted or
surface mounted using the MS-SB
backbox.
MS-MI Intelligent Manual Station

The MS-MI is an intelligent manual station
designed to interface with an analog loop.
The MS-MI is a single-action station; when
used with the MS-DA plate, the MS-MI is a
double-action station. The MS-MI can be
flush mounted or surface mounted using
the MS-SB backbox.
1-14
TRI-60, TRI-60R, and TRI-60D Intelligent

Interface Modules
The TRI-60 series modules are intelligent
interface modules that interface direct
shorting contact devices with the analog
loops. The TRI-60 is a single-input module;
the TRI-60R is a single-input module with
an independently controllable Form C relay;
the TRI-60D is a dual-input module.
TRI-B6, TRI-B6R, and TRI-B6D

Intelligent Interface Modules
The TRI-B6 series modules are intelligent
interface modules that interface direct
loops. The TRI-B6 is a single-input module;
the TRI-B6R is a single-input module with
an independently controllable Form C relay;
the TRI-B6D is a dual-input module.
TRI-B6M Addressable Interface Module

The TRI-B6M addressable interface module
interfaces direct shorting contact devices
with the analog loops. The TRI-B6M can
monitor a normally open or closed dry
contact and it can report the status of the
contact
TRI-S, TRI-R, and TRI-D Intelligent

Interface Modules
The TRI-S/R/D series modules are intelligent interface modules that interface direct
loops. The TRI-S is a single-input module;
the TRI-R is a single-input module with an
independently controllable Form C relay;
the TRI-D is a dual-input module.
CZM-1B6 Remote Conventional Zone

Module
The CZM-1B6 Remote Conventional Zone
Module supports one zone of non-addressable initiating devices in either Style D
(Class A) or Style B (Class B) configuration,
for a maximum of 15 compatible 2-wire
smoke detectors and an unlimited number
of shorting devices.
Description
The conventional devices described below
are available for use with the MXL-IQ
Control Panel.
The UL identifiers for compatibility are the
same as the model numbers.
DI-3 Ionization Detector

The DI-3 is an ionization detector for use in
open areas at altitudes of 0 to 4000 feet. It
uses the DB-3S low profile surface mounting base.
DI-3H Ionization High Altitude Detector

The DI-3H is an ionization detector for use
in open areas at altitudes of 3000 to 8000
feet. It uses the DB-3S low profile surface
mounting base.
DI-A3 Ionization High Air-Velocity

Detector
The DI-A3 is an ionization high air velocity
detector for use in open areas, computer
facilities, and air ducts at altitudes of 0 to
4000 feet and at air velocities of 0 to 1200
feet per minute. It uses the DB-3S low
profile surface mounting base.
DI-A3H Ionization High Air-Velocity,

The DI-A3H is an ionization high air
velocity, high altitude detector for use in air
ducts only at altitudes of 3000 to 8000 feet
and at air velocities of 300 to 1200 feet per
minute. It uses the DB-3S low profile
surface mounting base.
DI-B3 Ionization Air Duct Detector

The DI-B3 is an ionization detector for use
only in air ducts at altitudes of 0 to 4000
feet. It must be used with a Series 3 air
duct housing (AD-3I or AD-3RI).
DI-B3H Ionization Air Duct High

Altitude Detector
The DI-B3H is an ionization detector for use
only in air ducts at altitudes of 3000 to 8000
feet. It must be used with a Series 3 air
duct housing (AD-3I or AD-3RI).
DT-11 Thermal Detector

The DT-11 is a thermal detector for use in
open areas. It uses the DB-11 low profile
surface mounting base or the DB-3S
mounting base with the DB-ADPT adapter.
PE-3 Photoelectric Detector

The PE-3 is a photoelectric detector that
responds to a wide range of both flaming
and smoldering fire conditions. It uses
either the DB-3S low profile surface mounting base or the AD-3ILP or AD-3XRILP air
duct housing.
CONVENTIONAL
DEVICES
PE-3T Photoelectric Detector with Heat

Sensor
The PE-3T is a photoelectric detector with
heat sensor that responds to a wide range
of both flaming and smoldering fire conditions. It uses the DB-3S low profile surface
mounting base.
PE-11 Photoelectric Detector

The PE-11 is a photoelectric detector that
responds to a wide range of both flaming
and smoldering fire conditions. It uses the
DB-11 low profile surface mounting base,
the DB-3S mounting base with the
DB-ADPT adapter, or the AD-11P/11PR
air duct housing.
PE-11T Photoelectric Detector with

Heat Sensor
The PE-11T is a photoelectric detector with
heat sensor that responds to a wide range
of both flaming and smoldering fire conditions. It uses the DB-11 low profile surface
mounting base or the DB-3S mounting base
with the DB-ADPT adapter.
PBA-1191 Linear Beam Smoke Detector

The PBA-1191 can detect light or dark
smoke buildup at distances between the
transmitter (X) and receiver (R) of 17 feet to
280 feet. The PBA-1191 can be used in a
variety of areas, including large, narrow, or
high rooms, and rooms with high air
turbulence. The PBA-1191 requires the
PBB-1191 base.
NOTE: Only one PBA-1191, and no
additional devices, can be connected to a
CZM-4 initiating zone.
1-15
Description
1-16
+D=FJAH
Installation
Remove all system power
before installation, first
battery and then AC.
General Guidelines For Installing The

MXL-IQ
This section provides general installation

instructions for mounting, wiring, and
checkout of the CERBERUS PYROTRONICSTM
MXL-IQ Control System.
NOTE:
Read this section before installing the

equipment to ensure proper installation. If
you are not familiar with the MXL-IQ, also
read the first section of the manual. Be sure
to ask Siemens Building Technologies, Inc.
Technical Support or an authorized Representative if you have any questions.
Install and use the MXL-IQ System in
accordance with the appropriate Local,
NFPA, and NEC Code requirements.
INTRODUCTION
Always remove power (battery and AC)

and wait at least 10 seconds to allow the
supply voltages to decay before installing or
removing any module, cable, or wiring.
If available, use a printer during
the installation procedure as a
debugging tool.
Follow Steps 1 through 13 for installation.

Each step is thoroughly explained in the
following pages.
1. Install the enclosure (page 2-2).
2. Install the TSW-2 Tamper Switch
where required (page 2-2).
3. Pull the field wiring into the backbox
and dress it to approximately where it
will go (page 2-3).
4. Install the SMB-2 (page 2-3).
5. Install the MPS-6 (page 2-3).
6. Install the MKB-4 (page 2-4).
WARNING!
Refer to the last page of the
manual for a Warning Note
required by the FCC for all
commercial Class A computing
equipment producing a clock
frequency of 10K Hz or greater.
7. Install the PIM-1, PIM-2, and PAL-1 (If

applicable) (page 2-5).
8. Install the MOM-2 or MOM-4 card
(page 2-6).
9. Install the MOI-7, MOD-16, and MID-16
(If applicable) (page 2-9).
10. Install Field Wiring (page 2-10).
11. Check Field Wiring (page 2-10).
12. Start-up Procedure (page 2-10).
13. System Function Checkout (page 2-16).
2-1
Installation
1. Install the MSE-3L Enclosure

The MSE-3L is the enclosure for the MXL-IQ.
Consider the following when mounting the
backbox:
INSTALLATION
INSTRUCTIONS
FOR THE MXL-IQ
CONTROL PANEL
Mounting height for visual and manual

access to the MKB-4 Keyboard/annunciator
Weight and size of enclosure
Local Mounting codes
Fasten the backbox securely to a clean,
dry, shock-free, and vibration-free surface.
Position the backbox clear of obstructions
so that the door opens freely and so that
the indicators and controls are easily

accessible.
NOTE: When the backbox is mounted
semi-flush using the MET-3L kit, be sure
that the position of the backbox permits the
door to swing fully open. (See MET-3L
Installation Instructions, P/N 315-095447.)
When deadfront construction is required,
use the IQ-DFL panel (See IQ-DFL Installation Instructions, P/N 315-095446.)
When the MSE-3L is used for remote
applications, use the IQ-Blank where there
is no MKB-4 installed (See IQ-Blank
Installation Instructions, P/N 315-095482.)
To install the backbox: (Refer to Figure 21)
a. Slip the door off the hinges of the box
and put it to one side temporarily.
b. Remove the knockouts in the backbox
where field wiring is required (Refer to
MSE-3L Power Limited Wiring
Instructions, P/N 315-095445, for
location of knockouts).
c. Hold the empty enclosure against the
wall at a height that provides easy
access.
d. Mark drill points on the wall in the center
of the two slots on the upper rear of the
MSE-3L.
e. Drill the two holes and screw in the top
screws, leaving a small gap between the
wall and each top screw.
f. Mount the MSE-3L on the 2 bolts and
then install the bottom bolts.
Figure 21
Mounting the MSE-3L Enclosure
g. Slip the door back on the hinges of the

enclosure.
2. Install The TSW-2 Tamper Switch
(Refer to Figure 22)

If your configuration (UL 1076) requires the
TSW-2 Tamper Switch, install it now.
The TSW-2 mounts into the rectangular
slot located in the lower right side of the
MKB-4 panel.
1. Place the cable/connector and the switch
terminals through the opening and press
firmly into place.
Figure 22
TSW-2 Tamper Switch
2-2
2. Plug the cable on the TSW-2 into P9 on

the SMB-2 after installing the SMB-2.
Installation
3. Pull All Field Wiring Into The Backbox

Pull all field wiring into the backbox and
dress the wiring to the approximate location
to which it will go. Refer to the MSE-3L
Power Limited Wiring Instructions, P/N 315095445.
4. Install the SMB-2

Unpack the SMB-2. Inspect the module,
looking for such things as integrated
circuits (ICs) not firmly seated in their
sockets, bent IC pins, connectors not
properly installed, dirt, packing material on
the board, etc.
The installation kit consists of the following
items:
Two #6 nuts
Four #6 screws
Six #6 washers
Six #6 lockwashers
Two resistors
Battery cable with a wire
a. Place the SMB-2 over the two studs in
the upper right-hand portion of the
backbox (See Figure 23).
Figure 23
Installing the SMB-2
b. Secure in place using the hardware

provided.
Be sure the screws and nuts are tight, as
they provide the earth ground connection
for the SMB-2
5. Install the MPS-6/12
(See Figure 24)

The MXL-IQ is designed to operate from a
120 VAC, 60 Hz power source. Use a
separate or dedicated circuit-breaker. Wire
in accordance with local codes and Article
760 of the NEC, NFPA 70, latest edition.
Run the earth ground from a suitable
source to the MPS-6/12. Check local
requirements. Conduit is not an acceptable conductor.
Make sure that the dedicated circuit-breaker
for the MXL-IQ is turned off at the mains.
Place the mounting bracket for the MPS-6/
12 over the two studs provided in the
enclosure as shown in Figure 24.
Secure the MPS-6/12 to the MSE-3L by
slipping the flat washers, then the
Figure 24
Installing the MPS-6
2-3
Installation
lockwashers, and finally the nuts over the
two studs. Tighten them securely.
Connect the AC mains to MPS-6/12 as
follows:
Terminal
Black (hot)
White (neutral)
Green (earth ground)
1
2
3
Install the 14 gauge green ground strap

spade lug side to Terminal 3 (green, earth
ground) of the MPS-6 or MPS-12. Secure
the ring lug side of the ground strap to the
nearest available stud in the enclosure. The
stud size may vary depending on the actual
system modules and enclosure used.
Because the stud may be either a #10
thread of " thread, nuts for both have
been provided. The ground strap provided
is long enough for all applications and the
ring lug is good for both #10 and " studs.
If possible, install the ring lug under one of
the lockwashers and nuts which secure the
MPS-6 or MPS-12 itself.
Connect the 3-wire cable coming from the
MPS-6 to the SMB-2, P1, or connect the 8wire cable coming from the MPS-12 to the
SMB-2, P14.250
6. Install the MKB-4 Keyboard/

Annunciator

before installation, first
battery and then AC.
Unpack the MKB-4. Inspect the module for

such things as integrated circuits (ICs) not
firmly seated in their sockets, bent IC pins,
connectors not properly installed, dirt, and
packing material on the board.
NOTE: The MKB-4 is supplied with the
keyboard/annunciator mounted to the
hinged panel.
Setting the Network Address
(See Figure 25)
a. Before installing the MKB-4 panel, set its
network address on S1, the switch on
the ANN-1 board located on the back of
the MKB-4. Use dipswitches SW1 and
SW2 on switch S1 to set the network
address of the MKB-4. Refer to Table 2
for switch settings.
b. The MKB-4 module address is always
set within network addresses 248
through 251.
c. One supervised MKB-4 must be
installed at network address 251.
Other supervised MKBs may be at the
other addresses.
TABLE 2
SWITCH SETTINGS ON THE ANN-1
ADDRESS SETTINGS FOR:
SWITCH
248
249
250
251
S1-SW1
OpenOFF
ClosedON
OpenOFF
ClosedON
S1-SW2
OpenOFF
OpenOFF
ClosedON
ClosedON
S1-SW3
ClosedON
ClosedON
ClosedON
ClosedON
S1-SW4
ClosedON
ClosedON
ClosedON
ClosedON
S1-SW5
See Setting Supervision
NOTE: Switches S1-SW3 and S1-SW4 are for future use.

Switch S1-SW5 is used to select suptervision.
Figure 25
Setting S1 on the ANN-1 Board
2-4
Setting Supervision:
Use switch S1-SW5 on the ANN-1 to select
or deselect supervision. If your ANN-1 has
a switch with position 1 indicated on the
left-hand side, ignore the printing on the
switch. SW1 on S1 is at the extreme righthand side of S1, regardless of any other
marking.
Installation
NOTE: When you select non-supervision
for an annunciator, there must also be one
and only one supervised annunciator at
the same address. The supervisory mode
is independent of the network address.
To set for supervision
S1-SW5 = Closed (ON)
To set for non-supervision
S1-SW5 = Open (OFF)
Mounting the MKB-4
1. Install three screws in the first group of
three tapped holes in the right flange.
Leave a 1/8-inch gap between the head
of the screw and the flange. Slide the
slots of the MKB-4 panel hinge under the
head of the screws and tighten.
2. After the MKB-4 is mounted to the
enclosure, connect the cable (P/N 555192238) between P1 on the ANN-1 (on
the back of the MKB-4) and P8 on the
SMB-2.
Figure 26
Installing the MKB-4 Keyboard/Annunciator
MSE-3L
CAUTION:
Be sure the black tracer wire on the edge of
the cable is close to the 1 on position 1 of
connector P1 on the ANN-1 and the 1 on
position 1 of P8 on the SMB-2.
d
Cable supplie
with PIM-1
2)
24
92
(P/N 555-1
1
P1
P1 P2
7. Install the PIM-1, PIM-2, and PAL-1
Back of MKB-
TB1
PIM-1
ANN-1
To P8
o
(Cable n the SMB
-2
suppli
ed wit
h MK
B-4)
PIM-1
1. Install the PIM-1 on the back of the
MKB-4 panel as shown in Figure 27.
Position the PIM-1 so the TB1 is on the
left side of the board.
2. Mount the PIM-1 module on the raised
studs with the hardware provided.
3. Using the cable supplied with the PIM-1,
connect PIM-1, P-1 to ANN-1, P1 (See
Figure 27).
4. Using the cable supplied with the MKB-4,
connect PIM-1, P2 to SMB-2, P8 (See
Figure 27).
Figure 27
Installing a PIM-1 on the Back of an MKB-4
2-5
Installation
PIM-2/PAL-1
The PIM-2 and printer require a standby
power source in the event of a loss of
primary input power (AC mains). Refer to
Figure 28 for the connection of a UPS to
meet this requirement.
5. Set the dipswitches on the back of the

PIM-2 to agree with the communications
parameters configured in the CSG-M.
Refer to Table 4 for the dipswitch
definitions.
1. Before installing a PIM-2 in the MXL-IQ

system, a PIM-1 must be already
installed.
8. Install the MOM-2 or MOM-4
2. Wiring from the PIM-1 to the PIM-2 must

be within 25 feet in rigid conduit (Refer to
Table 3).
TABLE 3
PIM-1 TO PIM-2 INTERFACE REQUIREMENTS
(Supplied by installer)
PIM-1, TB
4 (Rx)
5 (Tx)
7
3 (BUSY)
2 (COMMON)
TO
PIM-2 Inpt Pin No.

2 (TxD)
3 (RxD)
4, 5 (RTS, CTS)
20 (DTR)
7 (GRD)
Use 18 AWG wire minimum.
3. Figure 29 shows the proper installation

of the PIM-2 with the MXL-IQ system.
4. Programming the CSG-M is required
when using a PIM-2 and parallel printer.
Configure one of the following four
printer types on the MKB-4:
Supervised PIM-2
80 column color
Supervised PIM-2
132 column color
Supervised PIM-2
80 column
Supervised PIM-2
132 column (for
PAL-1 and NFPA 72 Proprietary)
NOTES:
1. All wires 14 AWG min,
600V insulation.
2. Wiring to the printer and
PIM-2 must be 14 AWG
min, 600V insulation in
conduit.
3. Use the UPS ICS Lifeline
Model 9300057.
4. Standby Power
requirements: 120 VAC,
0.6A for 24 hours.
5. Standby Power
requirements: 120 VAC,
0.15A for 24 hours.
Figure 28
UPS Wiring Diagram
2-6
If a system requires the MOM-2 or MOM-4

optional card cage (Figures 10 and 11,
page 20), now is the time to install it.
Unpack the card cage and its attached
backplate and inspect it, looking for such
things as connectors not properly
installed, dirt, and packing material on the
board.
The MOM-2/4 installation kits include the
following items
MOM-2
MOM-4
3 #10 nut s
4 #10 nut s
3 #10 flat washers
4 #10 flat washers
3 #10 lockwashers
4 #10 lockwashers
4 #6 x 7/16 screws
1 8-conductor ribbon cable
2 #6-32 x 5/16 screws
2 2-wire cables
1 8-conductor ribbon cable
4 card guides
2 2-wire cables
2 card guides
Installation
TABLE 4
SERIAL INTERFACE COMMUNICATION PARAMETERS
Dipswitch Position (SW1) -Located at rear of PIM-2
BAUD RATE
960 0
480 0
240 0
120 0
30 0
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
OFF
ON
ON
ON
DATA BITS
8
7
OFF
ON
PARITY
Even
Odd
OFF
ON
PARITY
Disable
Enable
OFF
ON
FLOW CONTROL
Hardware
Software
OFF
ON
PORT TYPE
OFF
NOTE:
When setting Switch S1,
OFF=UP=OPEN
ON=DOWN=CLOSED
ANN-1
MKB-4
PIM-1
SEE INSTL. INSTR.
P/N 315-091462
TB1
CABLE NOT SUPPLIED

(SEE NOTE 1)
SUPERVISED
PARALLEL PRINTER (REAR VIEW)
PIM-2 (REAR VIEW)

(REFER TO TABLE 4)
120 VAC
60 Hz
CENTRONICS PARALLEL
OUTPUT
CABLE SUPPLIED WITH PIM-2

(SEE NOTE 2)
SUPERVISED
(REFER TO NOTES 9 AND 10)
THE CONNECTION IS NOT
SUPERVISED FOR DATA
INTEGRITY BETWEEN PIM-2
AND THE PRINTER.
Figure 29
PIM-2 to MXL-IQ Wiring Diagram
PIM-2 POWER TRANSFORMER

SUPPLIED WITH PIM-2 (SEE NOTE 3)
INPUT
SW1
PWR
XFMR
INSTALL IN UL LISTED GANGBOX
PIM-2 POWER CABLE

MUST BE IN CONDUIT
NOTES:
1. Maximum cable
distance from PIM-1 to
PIM-2 cable is 25 feet.
The two modules must
be in the same room.
2. The maximum distance
from the PIM-2 to the
parallel printer is 6 feet.
The two modules must
be in the same room.
3. PIM-2 power (PWR) is
connected to the 5
VDC, 600mA transformer supplied with the
PIM-2. The transformer
requires 120 VAC, 60
Hz, 0.5A max.
4. For NFPA 72 Local,
Auxiliary, and Remote
Station configurations,
connect the output of
the PIM-2 to any UL
listed EDP Centronics
parallel printer.
5. The parallel printer must
support the EPSON FX
command set.
6. The PIM-2 input and
output connectors are
DB-25 female.
7. Pressing RESET on the
PIM-2 causes the unit
to read the SW1
settings. The status
LED is lit when the unit
is powered. Do not use
the COPY button.
8. For NFPA Proprietary
and UL 1076
configurations, use
parallel printer Model
PAL-1, a UL listed for
fire Centronics parallel
printer.
9. The parallel printer is
supervised for AC, on/
off line, paper out, paper
jam, and connection to
the PIM-2.
10. The PIM-2 is
supervised for power,
connection to the
printer, and connection
to the PIM-1.
11. After loading paper in
the PAL-1 printer, turn
off the power and follow
the steps below:
While pressing the
LOAD PARK button,
turn on the power to
the PAL-1 printer.
Continue pressing
the LOAD PARK
button for 5 seconds.
Release the LOAD
PARK button.
The current setting
will print.
When printing is
completed, the ON
LINE indicator will be
lit. If the ON LINE
indicator is not lit,
press the ON LINE
button.
2-7
Installation
To mount the MOM-2/4 in an MSE-3L
enclosure:
1. Hold the MOM-2/4 so that terminal
blocks TB2 and TB4 are on the left.
2. Place the module vertically on the
mounting studs near the top left of the
enclosure as shown in Figure 23 on
page 2-3.
3. Fasten the MOM-2/4 in position with the
No. 10 flatwashers, lockwashers, and
nuts provided.
To install the card guides
(See Figures 30 and 31):
Install the card guides included in the
package using the #6 x 7/16 screws
provided. (The MOM-4 is shipped with the
MOM-2
mounting screws for the card guides

already installed.)
1. Mount the long screws.
2. Make sure that the locating pin on the
guide is seated in the hole on the
MOM-2/4.
3. Tighten the screw.
Repeat this process for the remaining card
guide(s). The MOM-2/4 is now ready to
accept the optional modules. If the system
does not require the installation of any halfwidth modules, install the two #6 x 5/16
screws in the center holes where the
additional card guides would be placed.
Plug-in Cards for the MOM-2/4
Determine which optional plug-in modules
are used in your CSG-M configuration.
Next, decide where they should be installed
by checking the following factors:
1. The size of each module. The CSM-4
and CRM-4 each occupy two adjacent
slots.
2. How the field wiring will be installed.
Figure 30
Installing the MOM-2 Card Guides
3. The maximum load current permitted for

the MOM-2/4 is 6 amps for the MPS-6 or
12 amps for the MPS-12. This current
must be derated by the current drawn
from SMB TB5 (CZM-1B6 power and
NAC #1 and NAC #2). When the system
includes an external auxiliary power
supply, the maximum load current
permitted depends on the application.
Refer to Table 5 for the maximum
current required by each module under
full load conditions.
MOM-2/4 Electrical Installation
1. Attach the 8-conductor ribbon cable to
P6 on the SMB-2, engaging the locking
rib of the cable with the locking tab on P6.
2. Attach the other end of the 8-conductor
ribbon cable to P7 on the MOM-2/4,
engaging the locking rib of the cable with
the locking tab on P7.
3. Connect one end of the 2-wire 24 VDC
cable to P3 on the SMB-2, using the
locking tab to lock the cable onto P3.
Figure 31
Installing the MOM-4 Card Guides
2-8
Installation
4. Connect the other end of the 2-wire
cable into P5 on the MOM-2/4. The
2-wire cable that attaches P5 on the
MOM-2/4 with P3 on the SMB-2 feeds
24 VDC full-wave unfiltered DC power to
the MOM-2/4. This is the main power
used by the optional modules. The
8-conductor ribbon cable supplies 5 VDC
and communication between the SMB-2
and the MOM-2/4.
9. Install the MOI-7, MOD-16, and

MID-16
MOI-7
1. Mount the MOI-7.
TABLE 5
MAXIMUM MODULE LOAD CURRENTS
ALD-2I
CMI-30 0
CRM-4
CSM-4
CZM-4
NIM-1R
90mA (120 devices in alarm)

96mA
75mA (4 relays energized)
34mA (no alarm indicating appliances connected)
720mA (maximum with 4 zones in alarm)
0mA
The following example assumes that no power is drawn from SMB-2 TB5
(CZM-1B6 power and NAC #1, NAC #2).
Example:
With 1 CZM-4 + 1 CRM-4 + 1 CSM-4, the total load current = 0.72 +
0.075 + 0.034 = 0.83A
The remaining available current = 12.0 (MPS-12) or 6.0 (MPS-6) - 0.83 =
11.83 (MPS-12) or 5.83 (MPS-6).
The MOI-7 mounts on a System 3 rail in

two module spaces. Mount the MOI-7
using the four screws provided.
The remaining current may be used for NAC power.
2. Set the network address on S1.

Set the address according to Table 16 at
the end of this chapter so that it agrees
with the address assigned in CSG-M.
3. Use P6 to set the mode for common
alarm relay K1. (See Figure 17,
page 1-10, for the location of P6.)
K1 is a common alarm relay that can be
programmed to transfer back to normal
when the MXL-IQ is silenced.
Use jumper P6 on the MOI-7 to select the
desired mode according to the table below.
P6 Position
Mode
Alarm Relay Silenceable
Alarm Relay Non-silenceable
3. If a connection to a MOD-16 module on

another rail is required, use the optional
cable P/N 555-190941.
MID-16 (See Figure 19, page 1-11)
1. Mount the MID-16 in one System 3 type
module space using the four screws
provided.
2. Connect the MID-16 to the module to its
left with the 10-position ribbon cable P/N
555-190940 provided. This module may
be either an MOI-7, MOD-16, or MID-16.
3. If a connection to a module on another
rail is required, use the optional cable
P/N 555-190941.
MOD-16 (See Figure 18, page 1-10)

1. Mount the MOD-16 in one System 3 type
module space using the four screws
provided.
2. Connect the MOD-16 to the MOI-7 with
the 10-position ribbon cable P/N 555190940 provided with the MOI-7.
2-9
Installation
10. Install Field Wiring
TABLE 6
WIRING TO THE SMB-2
Screw Terminal
Application
TB5 12-9
TB5 8-5
TB5 4-1
CZM-1B6 Power
Notification Appliance Circuit 2
TB4
TB4
6-4
3-1
Trouble Relay
Alarm Relay
TB3
TB2
4-1
4-1
Analog Loop 2
Analog Loop 1
TB1
TB1
TB1
1-2
3
4-5
MXL-IQ Network for MOI-7 and RCC-1/1F

Do Not Use
MPS-6/12 and MOM-2/4
NOTE: See SMB-2 Connections and Ratings for a more detailed description of the
screw terminals.
Wiring to the SMB-2

Refer to Table 6. Dress the field wiring that
will be going to the SMB-2. Strip the
insulation from the wiring, but do not
connect the wires to the screw terminals.
Wiring to the MOM-2/4 Optional Modules (if
Required)
Refer to Table 7. Dress the field wiring that
will be going to the MOM-2/4 modules. Strip
the insulation from the wiring and connect
the wires to the appropriate screw terminals.
11. Check Field Wiring

TABLE 7
WIRING TO THE MOM-2/4 OPTIONAL MODULES
Module
CSM-4
Screw Terminal
1-4
9-12
Application
NOTE: See CSM-4 Connections and Ratings for a more detailed description of the screw
terminals.
CRM-4
1-3
4-6
11-13
14-16
Dry Contact 1
Dry Contact 2
Dry Contact 3
Dry Contact 4
NOTE: See CRM-4 Connections and Ratings for a more detailed description of the screw
terminals.
CZM-4
1-4
5-8
9-12
13-16
Conventional
Conventional
Conventional
Conventional
Zone 1
Zone 2
Zone 3
Zone 4
NOTE: See CZM-4 Connections and Ratings for a more detailed description of the screw
terminals.
CMI-30 0
1-4
CXL Modem Connection
NOTE: See CMI-30 0 Connections and Ratings for a more detailed description of the screw
terminals.
NIM-1R
1-2
3-4
12-16
XNET Network Pair A / FSI / AnaLASER

XNET Network Pair B
NCC XNET Interface
NOTE: See NIM-1R Connections and Ratings for a more detailed description of the screw
terminals.
ALD-2I
1-4
5-8
Initiating Devices
Install all initiating device bases and end-ofline devices where applicable. Install all
initiating devices. Refer to the specific
installation instructions provided with each
device.
Notification Appliances
Install all notification appliances (bells,
strobes, etc.) Refer to the specific installation instructions provided with each device.
Check Resistance Between Wiring Circuits
Start with the wire that goes to TB5-12 on
the SMB-2. Check the resistance between
that wire and all other field wires that will be
connected to the SMB-2. Also, check the
resistance between that wire and all wires
connected to the screw terminals on the
MOM-2/4. Refer to Table 8 for acceptable
resistance readings. If the readings are
good, connect the wire to TB5-12. Repeat
the above procedure for the next wire on
the SMB-2.
When the SMB-2 is complete, continue with
the MOM-2/4 (if it is installed).
Analog Loop 1
Analog Loop 2
NOTE: See ALD-2I Connections and Ratings for a more detailed description of the screw
terminals.
12. Start Up Procedure

NOTE: Throughout this section, refer to the
TROUBLESHOOTING GUIDE as an aid to
resolving trouble conditions.
2-10
Installation
1.System Status
When beginning the start-up procedure, the
condition of the system is as follows:
All field wiring is connected to all screw
terminals, except for the analog loops
they should be disconnected. All field
devices are installed.
TABLE 8
FIELD WIRING CHECKOUT
SMB-2 EXTERNAL WIRING AND TROUBLESHOOTING GUIDE
TB-5
Resistance
Between Wires
1.
Chassis to 1-12
2.
Desired Results
Probable Cause Of Problem
>1 Meg
Short in wiring.
11 to 12
<1.5 ohms
Line open; Line too long.
3.
9 to 10
<1.5 ohms
4.
7 to 8
<1.5 ohms
5.
5 to 6
<1.5 ohms
6.
3 to 4
<1.5 ohms
7.
1 to 2
<1.5 ohms
8.
9 to 12
>1 Meg
Line shorted.
9.
5 to 8
>1 Meg
Line shorted.
3.SMB-2 Checkout Minus the Analog Loops

Turn on the AC power to the system.
10.
1 to 4
>1 Meg
Line shorted.
11.
9-12 to 1-8
>1 Meg
Line shorted.
The power light on the MKB-4 turns on
12.
5-8 to 1-4
>1 Meg
Line shorted.
No modules are installed in the MOM-2/4

cage.
2.Create a Test Configuration
Create a test configuration on your CSG-M
that includes every module that will be on
your final system. Do not include any
initiating devices. You will use this test
configuration in checking out the System.
the System displays the default message:

13.
8 (+) to 5 (-)
2.2K 10%
Line shorted; Line open; Wrong

EOL device; No EOL device; Device
wired backward; Device not
polarized.
14.
4(+) to 1 (-)
2.2K 10%
Line shorted; Line open; Wrong

EOL device; No EOL device; Device
wired backward; Device not
polarized.
15.
>1 Meg
>1 Meg
>1 Meg
Line shorted.
After the transfer process is complete,

MXL-IQ resets itself; after 5 minutes, the
state of the system should be as follows:
12 to 1-8
12 to TB2/3 1-4
12 to all MOM-2/4
16.
>1 Meg
>1 Meg
>1 Meg
Line shorted.
No trouble condition for the signaling

circuits on the main board.
8 to 1-4
8 to TB2/3 1-4
8 to all MOM-2/4
17.
4 to TB2/3 1-4
4 to all MOM-2/4
>1 Meg
>1 Meg
Line shorted.
TB-2
and
TB-3
Resistance
Between Wires
1.
Chassis to all
terminals
2.
MXL
Transfer the test configuration from your

computer to the MXL-IQ. Refer to the
CSGM Manual (P/N 315-090381) for the
correct procedure.
A battery trouble condition if the battery

option was selected.
All optional modules configured on the
system are in trouble since they are not
yet installed.
4.SMB-2 Analog Loop Checkout
Modify your test configuration by adding to
it the analog devices that are connected to
analog loop 1.
Turn off the power and connect the field
wiring to analog loop 1 on the SMB-2.
Turn on the power. Wait for the System
to initialize (approximately 3 minutes).
Desired Results
Probable Cause Of Problem
>1 Meg
Short in wiring.
1 to 2
<50 ohms
Open in wiring; Line too long.
3.
3 to 4
<50 ohms
Open in wiring; Line too long.
4.
1 to 4
<.4F
Too much wire.
5.
1 (+) to 4 (-)
>10K ohms
Line shorted.
6.
TB-2 (1-4) TB-3 (1-4)
>1 Meg
Line shorted.
7.
TB-2 (1-4) TB-5 (1-12)
>1 Meg
Line shorted.
8.
TB-3 (1-4) TB-5 (1-12)
>1 Meg
Line shorted.
(+) and (-) indicate meter lead polarity.

> = greater than; < = less than
2-11
Installation
Check the trouble list on the MKB for
troubles on the devices that were just
added. The troubles will be from among
the following (See Appendix J for a
complete list of Trouble Messages):
Device multiple response
Input device not responding
Incorrect device ID
Unspecified device responding
Identify the addresses of the devices
with troubles and eliminate them, reset
the system, and verify that the troubles
have cleared before proceeding.
Modify your test configuration by adding
to it the analog devices that are connected to analog loop 2.
To install the card guide that comes with

the CRM-4 and the CSM-4 module:
a Loosen the appropriate screw in the
center of the MOM-2/4 and set the card
guide in place.
Make sure that the locating pin on the
bottom of the card guide is in the hole on
the MOM-2/4.
b. Tighten the screw on the MOM-2/4 to
secure the card guide.

6.ALD-2I Checkout

Installing the ALD-2I

Set the address of each ALD-2I. Refer to

the CSG-M printout of the final configuration for the address to which each ALD-2I
should be set. Refer to the ALD-2I Installation Instructions (P/N 315-091464) to set
the address dipswitch.

Incorrect device ID
have cleared.
5.MOM-2/4 Optional Modules Checkout

before installing any
optional module
(ALD-2I, CMI-300, CRM-4,
CSM-4, CZM-4, NIM-1R).
2-12
Unpack each module just before installation. Inspect the module, looking for such
things as integrated circuits (ICs) not firmly
seated in their sockets, bent IC pins,
connectors not properly installed, dirt, and
packing material on the board.
Install the ALD-2Is one at a time by inserting them in the appropriate card guides on
the MOM-2/4. Make sure that the card is
firmly seated in the card edge connector.
Eliminate all troubles from each module
before installing the next one.
it any initiating devices that are connected
to the first analog loop on the ALD-2I.
Turn off the power; connect the field wiring
to analog loop 1 on the ALD-2I. Turn on
the power.
Installation

Incorrect device ID

Incorrect device ID



it any initiating devices that are connected
to the second analog loop on the ALD-2I.
Turn off the power; connect the field wiring
to analog loop 2 on the ALD-2I. Turn on
the power.
Installing the CMI-300 Interface Module

Before installing the CMI-300 in the
MOM-2/4, you must do the following:
1. Check that there is a jumper installed for
jumper J2, pins 1 and 2 on the CMI-300
module.
TABLE 9
Panel Number Programming (SW2)
ADDR
87654321
ADDR
000
0 01
0 02
0 03
0 04
0 05
0 06
0 07
0 08
0 09
010
011
012
013
014
015
---
FSI
SOOOOOOX
SOOOOOXO
SOOOOOXX
SOOOOXOO
SOOOOXOX
SOOOOXXO
SOOOOXXX
SOOOXOOO
SOOOXOOX
SOOOXOXO
SOOOXOXX
SOOOXXOO
SOOOXXOX
SOOOXXXO
SOOOXXXX
------------
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
---
87654321
SOOXOOOO
SOOXOOOX
SOOXOOXO
SOOXOOXX
SOOXOXOO
SOOXOXOX
SOOXOXXO
SOOXOXXX
SOOXXOOO
SOOXXOOX
SOOXXOXO
SOOXXOXX
SOOXXXOO
SOOXXXOX
SOOXXXXO
SOOXXXXX
------------
ADDR
87654321
ADDR
87654321
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
---
SOXOOOOO
SOXOOOOX
SOXOOOXO
SOXOOOXX
SOXOOXOO
SOXOOXOX
SOXOOXXO
SOXOOXXX
SOXOXOOO
SOXOXOOX
SOXOXOXO
SOXOXOXX
SOXOXXOO
SOXOXXOX
SOXOXXXO
SOXOXXXX
------------
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
SOXXOOOO
SOXXOOOX
SOXXOOXO
SOXXOOXX
SOXXOXOO
SOXXOXOX
SOXXOXXO
SOXXOXXX
SOXXXOOO
SOXXXOOX
SOXXXOXO
SOXXXOXX
SOXXXXOO
SOXXXXOX
SOXXXXXO
SOXXXXXX
SXOOOOOO
S = Closed selects Style 7

S = Open selects Style 4
O = Open or OFF
X = Closed or ON
NOTE:
To open a dipswitch, press down on the side of the dipswitch marked OPEN.
To close a dipswitch, press down on the side of the dipswitch opposite the side marked OPEN.
To open a slide switch, push the slide to the side opposite the side marked ON.
To close a slide switch, push the slide to the side marked ON.
2-13
Installation
2. Set the CMI-300 network address by
using the dipswitch settings on switch
SW1. Use Table 16 at the end of this
chapter to set the network address.
Plug the CMI-300 module in the MOM-2/4
card cage and connect the wiring as shown
in CMI-300 Connections and Ratings.
Eliminate all troubles from each module
prior to installing the next one.
Installing CRM-4 and CZM-4 Modules
Set the address of each module. Refer to
the CSG-M printout of the final configuration for each module address setting. Refer
to the installation instructions for each
module to set the address dipswitch.
Install the optional modules one at a time
by inserting them in the appropriate card
guides on the MOM-2/4. Eliminate all
troubles from each module prior to installing the next one.
Installing the NIM-1R Network Interface
Module
The NIM-1R installs into the MOM-2/4 card
cage where it occupies one full width slot.
The wiring is connected to TB4 of the
MOM-2 or TB3 of the MOM-4.
The NIM-1R has two configuration
dipswitches. Set the dipswitches before
installing the NIM-1R into the MOM-2/4.
Use switch SW1 to set the MXL-IQ network
address. Set this switch according to the
address where the NIM-1R is installed in
the MXL-IQs network map. Refer to the
CSG-M configuration printout for the
address of the module. See Table 16 at the
end of this chapter for settings.
Use switch SW2 to set either the panel
number for networked systems or to select
FSI or AnaLASER operation. Refer to Table
9 for panel settings, Table 10 for FSI
settings, or Table 11 for AnaLASER
settings.
1. When installing the NIM-1R in a
networked system, set the panel number
to agree with the panel number for the
NIM-1R assigned to the MXL-IQ System
in CSG-M.
2. Switch position 8 selects Style 4 or 7
operation for the NIM-1R network.
2-14
3. When installing the NIM-1R for FSI

operation, set the switch to all open (or
OFF).
TABLE 10
FSI Programming
ADDR
87654321
000
OOOOOOOO
O = Open or OFF
4. When installing the NIM-1R for

AnaLASER connection, set the switch as
follows:
TABLE 11
AnaLASER Programming
ADDR
87654321
AnaL ASER
XOOOOOOO
O = Open or OF F
X = Closed or ON
After setting the switches, install the

NIM-1R into the MOM-2/4 card cage. Make
sure that the module is in the card guides
and the card edge is firmly seated in the
connectors on the MOM-2/4.
Installing the CSM-4 Signal Module

Before installing the CSM-4 in the
MOM-2/4, you must set the network
address, configure each circuit according to
the CSG-M program [as Local (NACs),
Municipal Tie, Leased Line, or Releasing
Service], and set the default modes (trouble
and alarm) as follows. Refer to Table 12 for
the Modes of Operation.
a.Set the Network Address
The network address is set on dipswitch S1
(See Figure 12, page 1-8). See the CSG-M
printout for the proper address. Use Table
16 at the end of this chapter to set the
switches.
Installation
TABLE 12
Modes of Operation
b.Set the Mode of Operation for Each Circuit

The CSM-4 has one programming slide
switch and one jumper for each of its two
circuits. (See slide switches S3 and S4 and
jumpers G1 and G2 on the CSM-4 board,
Figure 12, page 1-8.) Setting these slide
switches and jumpers allows the selection
of four possible modes of operation. These
modes correspond with NFPA standards 72
Local, Municipal Tie, Leased Line, and
NFPA 12A, 13, and 2001 Releasing
Service.
Each circuit on the CSM-4 can be set
independently for the type of operation
desired. Table 12 shows how to set the
switches and jumpers for circuits 1 and 2.
The CSG-M printout shows the mode for
each circuit.
c.Set the Degrade Modes of Operation

There are two sources of degrade activation, the degrade alarm bus and the degrade trouble bus. These two buses
become active ONLY when the MXL-IQ
communication network fails. Dipswitch S2
on the CSM-4 sets the degrade mode of
operation for each circuit.
TABLE 13
Setting the Mode of Operation for the CSM-4
(Using S3, S4 and G1, G2)
For Circuit 1
Local (NAC)
Municipal Tie
Leased Li ne
Rel eas i ng Ser v i c e
Illegal (Results in a trouble
on t he CSM - 4)
For Circuit 2
Local (NAC)
Municipal Tie
Leased Li ne
Rel eas i ng Ser v i c e
Illegal (Results in a trouble
on t he CSM - 4)
S3
Position
G1
1
1
2
1
2
No t C u t
Cut
No t C u t
Cut
Cut
S4
Position
G2
1
1
2
1
2
No t C u t
Cut
No t C u t
Cut
Cut
Each circuit operates independently in the

degrade mode. Dipswitch S2, positions
SW1 and SW2, determines the degrade
mode of operation when the trouble bus
activates. Dipswitch S2, positions SW3SW6, determines the degrade mode of
operation when the alarm bus activates.
2-15
Installation
d.Degrade Trouble Activation
The degrade trouble bus may ONLY be
used when the circuit is used as a Leased
Line trouble indicating circuit. (See Table
12.) When enabled, this trouble degrade
mode ensures that a trouble will be transmitted to the receiving station even when
the MXL-IQ communication network fails.
Determine which type of degrade mode you

want for each circuit and set dipswitch S2
(SW3-SW6) as shown in Table 15.
Using the CSG-M printout, determine if

either of the circuits is configured as a
Leased Line trouble. Table 14 shows how
to set dipswitch S2 (SW1 and SW2) to
enable the degrade trouble activation for
the desired circuit.
The status of the MXL-IQ before checkout

must be as listed below:
TABLE 14
Setting the Degrade Trouble Modes
for the CSM-4 on S2
SW1
G1
For Circuit 1
Leased Line Trouble
No Trouble Activation
On (Closed)
Off (Open)
SW2
G2
For Circuit 2
Leased Line Trouble
No Trouble Activation
On (Closed)
Off (Open)
No t e :
If Circuit 1 or Circuit 2 is not used for Leased Line trouble,
switches SW1 or SW2 must be off (open).
e.Degrade Alarm Activation

Each circuit on the CSM-4 can be set with
dipswitch S2, positions SW3-SW6, to
determine when the degrade alarm bus
activates (See Table 12). There are three
degrade alarm modes. Each circuit can be
set independently from the other.
TABLE 15
Setting the Degrade Alarm Modes for the CSM-4 on S2
For Circuit 1
OFF (no degrade activation)
CONTINUOUS (active on degrade alam)
1 SEC ON, 1 SEC OFF (infinite repeat)
DO NOT USE
For Circuit 2
OFF (no degrade activation)
CONTINUOUS (active on degrade alam)
1 SEC ON, 1 SEC OFF (infinite repeat)
DO NOT USE
SW4
SW3
OFF (Open)
OFF (Open)
ON (Closed)
ON (Closed)
OFF (Open)
ON (Closed)
OFF (Open)
ON (Closed)
SW4
SW3
OFF (Open)
OFF (Open)
ON (Closed)
ON (Closed)
OFF (Open)
ON (Closed)
OFF (Open)
ON (Closed)
NOT E : When circuits are used for leased line supervisory, the alarm degrade modes must
be OFF (Open).
2-16
13. System Function Checkout
1. AC and battery power connected and

turned on.
2. All modules installed and all field wiring
connected.
3. All initiating devices installed and
addressed.
4. All field wiring checked out.
5. The start-up procedure completed.
6. An CSG-M printout of the summary of
the System Configuration available.
7. For documentation purposes, set the
MXL-IQ time before proceeding.
8. Transfer the final version of the System
Configuration to MXL-IQ.
Follow the steps listed in System Operation Checkout.
System Operation Checkout
WARNING!
Prior to activating any initiating device,
take steps to prevent output circuits
from being activated. Failure to do so
may result in building EVAC (bells),
notification of fire department, elevator recall, etc.
Test these operations in accordance
with local codes and follow the direction of the authority having jurisdiction.
Observe all safety precautions.
Installation
Test
1. Observe the display on the MKB-4.
Response
The POWER LED should be on steady.
The TROUBLE LED should be off.
The following message should appear on the alphanumeric
display:
(Time and Date)
(System Custom Message)
SYSTEM
NORMAL
(It may take a few minutes after power-up before the message
System Normal appears.)
2. Activate every alarm causing initiating

device on the System in groups of 100 or
fewer. Reset the System prior to
activating each group of 100.
Every device alarms and there are no troubles annunciated.

Device LEDs should come on when the device is in alarm.
As each device is alarmed, the custom message appears on the
display, is recorded on the printer (if installed), and corresponds
to the CSG-M printout for that device.
The messages listed on the printer are in the order in which the
devices were alarmed.
Pressing the NEXT key on the MKB-4 displays the devices in
reverse order.
Check that all appropriate responses are activated.
3. Activate all supervisory devices on the

System.
Each device should cause a supervisory.

As each device changes state, the custom message appears on
the display, is recorded on the printer (if installed), and corresponds to the CSG-M printout for that device.
The messages listed on the printer are in the order in which the
devices were activated.
Pressing the NEXT key displays the devices in reverse order.
Check that all the appropriate responses are activated.
4. Activate all security devices on the

System.
Each device should cause a security condition.

As each device is activated, the custom message appears on
the display, is recorded on the printer (if installed), and corresponds to the CSG-M printout for that device.
2-17
Installation
Test
5. Activate all status devices on the
System.
Response
None of the devices should cause an alarm or trouble condition.
If there is a printer, the System should print the status of reporting devices.
As each device is activated, the custom message recorded on
the printer corresponds to the CSG-M printout for that device.
6. CRM-4 relays:
Verifies proper operation of the connected relay.
Refer to Control Output On/Off, page

3-38, and toggle each CRM-4 relay
assigned to the System.
Reset the System when this test is
complete.
7. CSM-4 relays:
Verifies proper operation of the connected relay.
Refer to Control Output On/Off, page

3-38, and toggle each CSM-4 relay
assigned to the System.
Reset the System when this test is
complete.
8. System Functions:
Check all functions that are defined in
the customer specifications.
Check that the correct relationships between initiating devices

and output functions occur as defined by the customer specifications.
Check that the appropriate NFPA and local codes are met
(Refer to the CSG-M Logical Function Summary.)
2-18
Installation
TABLE 16
NETWORK ADDRESS PROGRAMMING
ADDR
000
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
&%$#"!
ILLEGAL
ILLEGAL
ILLEGAL
OOOOOOXX
OOOOOXOO
OOOOOXOX
OOOOOXXO
OOOOOXXX
OOOOXOOO
OOOOXOOX
OOOOXOXO
OOOOXOXX
OOOOXXOO
OOOOXXOX
OOOOXXXO
OOOOXXXX
OOOXOOOO
OOOXOOOX
OOOXOOXO
OOOXOOXX
OOOXOXOO
OOOXOXOX
OOOXOXXO
OOOXOXXX
OOOXXOOO
OOOXXOOX
OOOXXOXO
OOOXXOXX
OOOXXXOO
OOOXXXOX
OOOXXXXO
OOOXXXXX
OOXOOOOO
OOXOOOOX
OOXOOOXO
OOXOOOXX
OOXOOXOO
OOXOOXOX
OOXOOXXO
OOXOOXXX
OOXOXOOO
OOXOXOOX
OOXOXOXO
OOXOXOXX
OOXOXXOO
OOXOXXOX
OOXOXXXO
OOXOXXXX
OOXXOOOO
OOXXOOOX
OOXXOOXO
OOXXOOXX
OOXXOXOO
OOXXOXOX
OOXXOXXO
OOXXOXXX
OOXXXOOO
OOXXXOOX
OOXXXOXO
OOXXXOXX
OOXXXXOO
OOXXXXOX
OOXXXXXO
OOXXXXXX
&%$#"!
ADDR
OXOOOOOO
064
OXOOOOOX
065
OXOOOOXO
066
OXOOOOXX
067
OXOOOXOO
068
OXOOOXOX
069
OXOOOXXO
070
OXOOOXXX
071
OXOOXOOO
072
OXOOXOOX
073
OXOOXOXO
074
OXOOXOXX
075
OXOOXXOO
076
OXOOXXOX
077
OXOOXXXO
078
OXOOXXXX
079
OXOXOOOO
080
OXOXOOOX
081
OXOXOOXO
082
OXOXOOXX
083
OXOXOXOO
084
OXOXOXOX
085
OXOXOXXO
086
OXOXOXXX
087
OXOXXOOO
088
OXOXXOOX
089
OXOXXOXO
090
OXOXXOXX
091
OXOXXXOO
092
OXOXXXOX
093
OXOXXXXO
094
OXOXXXXX
095
OXXOOOOO
096
OXXOOOOX
097
OXXOOOXO
098
OXXOOOXX
099
OXXOOXOO
100
OXXOOXOX
101
OXXOOXXO
102
OXXOOXXX
103
OXXOXOOO
104
OXXOXOOX
105
OXXOXOXO
106
OXXOXOXX
107
OXXOXXOO
108
OXXOXXOX
109
OXXOXXXO
110
OXXOXXXX
111
OXXXOOOO
112
OXXXOOOX
113
OXXXOOXO
114
OXXXOOXX
115
OXXXOXOO
116
OXXXOXOX
117
OXXXOXXO
118
OXXXOXXX
119
OXXXXOOO
120
OXXXXOOX
121
OXXXXOXO
122
OXXXXOXX
123
OXXXXXOO
124
OXXXXXOX
125
OXXXXXXO
126
OXXXXXXX
127
O = OPEN (or OFF)
&%$#"!
ADDR
XOOOOOOO
128
XOOOOOOX
129
XOOOOOXO
130
XOOOOOXX
131
XOOOOXOO
132
XOOOOXOX
133
XOOOOXXO
134
XOOOOXXX
135
XOOOXOOO
136
XOOOXOOX
137
XOOOXOXO
138
XOOOXOXX
139
XOOOXXOO
140
XOOOXXOX
141
XOOOXXXO
142
XOOOXXXX
143
XOOXOOOO
144
XOOXOOOX
145
XOOXOOXO
146
XOOXOOXX
147
XOOXOXOO
148
XOOXOXOX
149
XOOXOXXO
150
XOOXOXXX
151
XOOXXOOO
152
XOOXXOOX
153
XOOXXOXO
154
XOOXXOXX
155
XOOXXXOO
156
XOOXXXOX
157
XOOXXXXO
158
XOOXXXXX
159
XOXOOOOO
160
XOXOOOOX
161
XOXOOOXO
162
XOXOOOXX
163
XOXOOXOO
164
XOXOOXOX
165
XOXOOXXO
166
XOXOOXXX
167
XOXOXOOO
168
XOXOXOOX
169
XOXOXOXO
170
XOXOXOXX
171
XOXOXXOO
172
XOXOXXOX
173
XOXOXXXO
174
XOXOXXXX
175
XOXXOOOO
176
XOXXOOOX
177
XOXXOOXO
178
XOXXOOXX
179
XOXXOXOO
180
XOXXOXOX
181
XOXXOXXO
182
XOXXOXXX
183
XOXXXOOO
184
XOXXXOOX
185
XOXXXOXO
186
XOXXXOXX
187
XOXXXXOO
188
XOXXXXOX
189
XOXXXXXO
190
XOXXXXXX
191
X = CLOSED (or ON)
ADDR
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
&%$#"!
XXOOOOOO
XXOOOOOX
XXOOOOXO
XXOOOOXX
XXOOOXOO
XXOOOXOX
XXOOOXXO
XXOOOXXX
XXOOXOOO
XXOOXOOX
XXOOXOXO
XXOOXOXX
XXOOXXOO
XXOOXXOX
XXOOXXXO
XXOOXXXX
XXOXOOOO
XXOXOOOX
XXOXOOXO
XXOXOOXX
XXOXOXOO
XXOXOXOX
XXOXOXXO
XXOXOXXX
XXOXXOOO
XXOXXOOX
XXOXXOXO
XXOXXOXX
XXOXXXOO
XXOXXXOX
XXOXXXXO
XXOXXXXX
XXXOOOOO
XXXOOOOX
XXXOOOXO
XXXOOOXX
XXXOOXOO
XXXOOXOX
XXXOOXXO
XXXOOXXX
XXXOXOOO
XXXOXOOX
XXXOXOXO
XXXOXOXX
XXXOXXOO
XXXOXXOX
XXXOXXXO
XXXOXXXX
XXXXOOOO
XXXXOOOX
XXXXOOXO
XXXXOOXX
XXXXOXOO
XXXXOXOX
XXXXOXXO
XXXXOXXX
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
ILLEGAL
2-19
Installation
2-20
+D=FJAH
Operation
This section provides instructions for
operating the MXL-IQ Control Panel.
Please review the introduction to the
MXL-IQ Control Panel at the beginning of
this manual.
ules and leaving gaps in the numbering,

provided you do not use the fixed addresses.
INTRODUCTION
The specific addresses of the System

modules are described in Table 17.
NOTE: See the Table of Contents pages at

the beginning of this manual for the order
of this chapter. Use it to find the answers to
specific questions when you are working
with the System.
TABLE 17
Fixed Module Addresses
Addresses
All modules and devices annunciated on the
MXL-IQ are identified by an address (MMMDDD). Each address is in two partsa
module address (MMM) and a device
address (DDD). The number identifying the
module may be as high as 254, and the
number identifying the device may be as
high as 248. Thus a device on a module
may be identified by any number between
001-001 and 253-250. (See Table 17.)
Fixed Addresses
A module may be assigned to any address
on the System, except for some fixed
addresses that have already been assigned
(See Table 17). The modules communicate
to the MXL-IQ Control Panel through a serial
communications network. The System
continuously supervises all of the modules
for presence and proper operation.
Module
Address
0
1
2
3
*
*
*
248
249
250
251
252
253
254
255
Module
Do not use
Analog loop 1 (SMB-2)
Analog loop 2 (SMB-2)
MKB-4
MKB-4
MKB-4
MKB-4, No. 1
Reserved
SMB-2
Programmer CSG-M
Global (reserved)
Device
Address
(Range)
0 01-060
0 01-060
0 01 to 250
You may assign a module to any address

on the System, and assign addresses in
any order, mixing different types of mod-
3-1
Operation
System Modules
ALD-2I Analog Loop Module
The ALD-2I takes two adjoining module
addresses. Loop 1 of the ALD-2I is at any
module address and loop 2 at the next
address. The analog loops on the SMB-2
are at module addresses 1 and 2 (See
Table 17, page 3-1) and cannot be moved.
The table below illustrates ALD-2I module
addresses:
ALD at Module
Addresses 3 and 4
Loop 1
Loop 2
Devices
003-001 to 003-060
004-001 to 004-060
ALD at Module
Addresses 15 and 16 Devices
Loop 1
015-001 to 015-060
Loop 2
016-001 to 016-060
CSM-4 Signal Module
The CSM-4 module contains two circuits
and two programmable LEDs.
Their device addresses on the module are
as follows:
Circuit 1
001
Circuit 2
002
LED 1
005
LED 2
006
For example, the address of circuit 2 on the

CSM-4 at module address 3 is 003-002.
CRM-4 Relay Module
The CRM-4 Relay module contains four
relays and two controllable LEDs.
Their device addresses on the module are
as follows:
Relay 1
001
Relay 2
002
Relay 3
003
Relay 4
004
LED 1
005
LED 2
006
For example, the address of relay 4 on the

CRM-4 at module address 20 is 020-004.
3-2

The CZM-4 Conventional Zone module
contains four conventional initiating device
zones and two programmable LEDs. Their
device addresses on the module are as
follows:
Zone 1
001
Zone 2
002
Zone 3
003
Zone 4
004
LED 1
005
LED 2
006
For example, the address of zone 1 on the

CZM-4, at module address 105, is 105-001.
MKB-4 Keyboard/Annunciator
The MKB-4 Keyboard/Annunciator occupies
the fixed module address 251 (See Table
17, page 3-1).
SMB-2 Main Board
The SMB-2 occupies module addresses 1,
2, and 253. The module addresses 1 and 2
are analog loops.
Module address 253 contains two notification appliance circuits (NACs) and two
relays. The device addresses at module
253 are as follows:
Common alarm relay
Common trouble relay
NAC 1
NAC 2
001
002
004
005
For example, the address of the common

alarm relay at module address 253 is
253-001.
Remote System Modules

The MOI-7 occupies one network address
and one network node in the MXL-IQ
System. Set the address on S1 (See Figure
17, page 1-10) according to Table 16, page
2-19, so that it agrees with the address
assigned in CSG-M.
The MOI-7 has a set of 128 subaddresses
reserved for the MOD-16 open collector
Operation
outputs and MID-16 general purpose
inputs. This gives a maximum of 8 MOD-16
boards and 8 MID-16 boards.
The MOI-7 subaddress map is as follows.
001-016 MOD-16/MID-16
#1
017-032 MOD-16/MID-16
#2
033-048 MOD-16/MID-16
#3
049-064 MOD-16/MID-16
#4
065-080 MOD-16/MID-16
#5
081-096 MOD-16/MID-16
#6
097-112 MOD-16/MID-16
#7
113-128 MOD-16/MID-16
#8
The MOI-7 has two status LEDs:
The TRANSMIT LED indicates that the
MOI-7 is sending information to the SMB-2.
During normal operation this LED flashes
periodically when the SMB-2 requests the
MOI-7s status.
The TROUBLE LED only lights when the
MOI-7 cannot communicate with the
MXL-IQ. This is an indication that the
network connection between the MOI-7 and
SMB-2 is damaged.
MOD-16 (Open Collector Output Module)
The MOD-16 does not occupy a network
address. The MOD-16 is at a subaddress
of the MOI-7 to which it is connected. The
subaddresses of any given MOD-16s are
determined by their position in the string of
MOD-16s.
The output cable from the MOI-7 connects
to the first MOD-16, which has the
subaddress of 001-016 as shown above.
Each additional MOD-16 in the chain has
the next block of 16 addresses.
You may connect a maximum of 8
MOD-16s and MID-16s to an individual
MOI-7 for a total of 128 open collector
outputs and 128 general purpose inputs.
Using The MKB-4

Keyboard/Annunciator
Panel in Local Mode
See Figure 32, page 3-4, for the location of

the display keys and LEDs.
When the MKB-4 Keyboard/ Annunciator
Panel is installed, only the display, LEDs,
and display control keys are visible. The
ACKnowledge keys and other controls are
hidden behind a locked door. Unlock and
open the door to gain access to those keys
and controls.
The Display
The display has two lines of 40 characters
each. What is shown on the display depends on the state of the System. The
display contains a back light which turns on
automatically when any key is pressed or
an event is reported. The back light turns
off automatically after 5 minutes of system
inactivity.
The System has several displays. When
the System is Normal, the display shows:
[time/date]
[system message]
SYSTEM
NORMAL
When an event has been annunciated, the

System alternates between the following
three displays:
[address] [custom message] [ACK STATUS or BLANK]
[event number] [device type] [trouble type] [IN or 0UT]
[address] [type of device in trouble] or [BLANK] [ACK

STATUS or BLANK] [event number] [time/date] [IN or 0UT]
ALARMS=nnn
TROUBLES=nnn
SUPERVISORIES=nnn
SECURITIES=nnn
3-3
Operation
The terms used in the displays described
above are defined as follows:
ACK appears if the event has been
acknowledged; otherwise, the field is
blank.
IN is displayed when a condition occurs.
OUT is displayed when a normal state is
restored.
[time/date] shows the time and date the

event occurred.
Internal Audible Alarm

The internal audible alarm (not visible)
sounds steadily when there is an unacknowledged fire alarm. It pulses if all
alarms are acknowledged, but there is at
least one supervisory, trouble, or security
condition.
Q The Display
A 2-line display of 40 characters each that

shows the state of the System. A back light
turns on when any key is pressed or an
event is reported.
Figure 32
MKB-4 Keyboard/Annunciator Panel
3-4
R System Control Keypad
ALARM ACK - Press to acknowledge a

fire alarm.
AUD SIL - Press to silence or unsilence
a notification appliance circuit.
SUPV ACK - Press to acknowledge a
supervisory.
TRBL ACK - Press to acknowledge a
trouble.
SEC ACK - Press to acknowledge a
security condition.
RESET - Press to reset the System.
S Numeric Keypad
Use the numeric keypad (keys 0 through 9)

when the System asks for a model number,
device number, password, time, date, or
other information. The display shows each
number as you press the key (except when
you enter a password; the System shows
an asterisk for each digit of the password
that you type).
Command Keypad
Left arrow (|) - Press to select the item to
the left of what is flashing on the display
(unless entering a number).
Right arrow (}) - Press to select the item to
the right of what is flashing on the display
(unless entering a number).
Up arrow (~) - Press to go back to the
previous item.
ENTER - Press to select the item on which
the cursor is flashing. When typing in
numbers, press ENTER when finished to
complete the entry.
PRINT - Press to print selected lists and
reports.
FORM FEED - Press to advance the paper
in the printer.
CLEAR - Press to cancel printing begun by
pressing PRINT. The System will print:
This listing prematurely terminated.
HELP - Press to display a one-line help

message.
U The Special (ALT and Function) Keypad
Use the four function keys alone or in

combination with ALT1 or ALT2 to provide
a total of 12 special functions. When using
a combination, hold the ALT key down and
then press the function key.
F1
F2
F3
F4
ALT1-F1
ALT1-F2
ALT1-F3
ALT1-F4
Hold ALT, then press
ALT2-F1
function key.
ALT2-F2
ALT2-F3
ALT2-F4
The special function keys are defined using
the CSG-M Custom Software Generator
(See CSG-M Programming Manual, P/N
315-090381). These definitions can be
recorded in the box on the panel.
V Display Keys
Operation
The MXL-IQ has two display keys, NEXT

and HOLD, located on the MKB-4.
NEXT - Press NEXT to show the previous
item in a list of Alarms, Supervisories,
Troubles, or Security conditions.
HOLD - Press HOLD at any time to freeze
the present display. The display remains
frozen until HOLD is released.
LEDs
ALARM - This red LED flashes when there
is at least one unacknowledged fire alarm;
it glows steadily when all fire alarms are
acknowledged.
AUDIBLE SILENCE - This red LED flashes
when at least one notification appliance
circuit (NAC) is active; it glows steadily
when all silenceable NACs are silenced.
Under normal conditions, the LED is off.
SUPERVISORY - This yellow LED flashes
when there is at least one unacknowledged
supervisory; it glows steadily when all
supervisories are acknowledged.
TROUBLE - This yellow LED flashes when
there is at least one unacknowledged
trouble; it glows steadily when all troubles
are acknowledged.
SECURITY - This yellow LED flashes when
there is at least one unacknowledged
security condition; it glows steadily when all
security conditions are acknowledged.
POWER - This green LED glows steadily to
indicate that the AC power is on; it flashes
when the System is on battery backup.
PARTIAL SYSTEM DISABLE - This yellow
LED glows steadily when any device is
disabled.
Modes Of Operation
INTRODUCTION
The MXL-IQ alphanumeric display annunciator has five modes of operation:

1.
2.
3.
4.
5.
Alarm
Supervisory
Trouble
Security
Normal
3-5
Operation
This order ensures that fire alarms always
take priority over all other conditions. In turn,
supervisories always take priority over
troubles and troubles always take priority over
security conditions. All of the above modes
take priority over Normal mode, which is the
absence of any alarms, supervisories,
troubles, or security conditions.
Alarm
The alphanumeric display shows an alarm
message when a fire alarm is received.
See Alarm.
Supervisory
The alphanumeric display shows a supervisory message when the system receives a
supervisory and no higher priority event is
present. See Supervisories, page 3-8.
Trouble
The alphanumeric display shows a trouble
message when a trouble is present and no
higher priority event is present. See
Troubles, page 3-9.
Security
0
0
0
0
ALARM
SUPERV
TROUBLE
SECURITY
0
0
0
0
ALARM ACK
SUPERV ACK
TROUBLE ACK
SECURITY ACK
Alarm
RESPONDING TO AN ALARM
1. Follow the response plan approved by
the local authority having jurisdiction.
2. When the MXL-IQ is installed, the
ACKnowledge key and Audible Alarm
Silence key (AUD SIL) on the MKB-4
are behind a locked door. The display,
LEDs, and display control keys are
visible and accessible. To acknowledge
an alarm or trouble, or to silence an
audible alarm, first unlock and open the
door.
How The System Annunciates Fire

Alarms
Normal mode is the absence of any alarms,

supervisories, troubles, or security conditions.
When a fire is detected, the System causes

the ALARM LED on the MKB-4 to flash, the
Systems internal audible to sound, the
AUD SIL LED to flash, and the alphanumeric display on the MKB-4 to alternate in a
sequence among the three messages
shown below. This example assumes that
two fire alarms were received (Refer to the
explanations below).
Message 1:
In normal mode the display shows the

following message:
1-001 [custom message]

002 [device type] IN ALR
11:59:59 DEC 31, 20XX

SYSTEM
[custom system message] NORMAL
Message 2:
The alphanumeric display shows a security

message when a security condition is
received and no higher priority event is
present. See Security Conditions, page 3-10.
Normal Mode
The POWER LED glows steadily in normal

mode when the system has AC power. The
ALARM, AUDIBLE SILENCE, SUPERVISORY, TROUBLE, and SECURITY LEDs
are off and the internal audible is off.
If your System has the printer option, the
System prints a message in the following
format every day at midnight, even when
there are alarms or other conditions:
3-6
System Status at 00:00:00 Jul 02, 20XX

002 [time/date] IN ALR
Message 3:
ALARMS=002
SUPERVISORIES=000
TROUBLES=000
SECURITIES=000
In addition, the System responds to alarms

with programmed output functions such as
other audible signals.
Operation
In the messages above, 1-001 represents
the address of the device reporting the
alarm.
NOTE:
On the display, not all leading

zeros are shown. If your System
includes a printer, note that the
leading zeros are not shown.
002 in the first message tells you that this is

the second (and the most recent) of two
alarms received.
The status information in the third message
reports the total of alarms, supervisories,
troubles, and security conditions.
If your System includes a printer, it prints a
message from two to four lines long similar
to the following:
ALARM 1-1 11:59:59 DEC 31, 20XX
#1 [custom message], [device type]
In the preceding printed message, ALARM

indicates that the type of occurrence is a
fire alarm; 1-1 is the device address; #1 is
the number of the alarm in the list of fire
alarms; [custom message] is a custom
message entered using the CSG-M Custom Software Generator (See the CSG-M
Programming Manual, P/N 315-090381);
[device type] is the type of device which
reported the alarm.
Viewing the List of Alarms

To see the alarm list when there is more
than one alarm, press NEXT on the MKB-4
(the System displays the most recent alarm
first).
How to Block Acknowledge a Fire

Alarm (NFPA 72 Local, Municipal Tie,
and Remote Station)
1. Note the specific location of the alarm(s)
by using the procedures described
above.
2. Unlock and open the door.
3. Press ALARM ACK to acknowledge all
alarms. The System displays the
following message:
ALL ALARMS ACKNOWLEDGED.
4. If your System includes the printer

option, it prints the following message:
ACK ALARM 11:59:59 DEC 31,20XX
ALL ALARMS ACKNOWLEDGED
5. If you press ALARM ACK again, the

System displays ALL ALARMS
ACKNOWLEDGED.
The ALARM LED glows steadily to
indicate that all alarms are acknowledged.
If there are no supervisories, troubles, or
security conditions in the System, the
internal audible goes silent; if any of
those conditions still exist, the internal
audible pulses.
How to Individually Acknowledge a Fire

Alarm (NFPA 72 Proprietary, UL 1076)
1. Press ALARM ACK. The System
acknowledges the alarm displayed and
then displays the next unacknowledged
alarm.
If your System has the printer option, it
prints an alarm acknowledgment
message similar to the following:
ACK ALARM 1-5 12:01:28 DEC 31,20XX
Note that the acknowledgments

message includes the term ACK to
indicate this alarm was acknowledged.
2. Continue acknowledging alarms as
explained above until the System
displays the following message: ALL
ALARMS ACKNOWLEDGED.
The ALARM LED glows steadily to
indicate that all alarms are acknowledged. If there are no supervisories,
troubles, or security conditions still in the
System, the internal audible goes silent;
if any of those conditions still exist, the
internal audible pulses.
3. If your System includes a printer, it prints
a message similar to the following:
ACK ALARM 12:05:44 DEC 31,20XX
Silencing The System

Press AUD SIL after all alarms are acknowledged. The System displays the
following message: AUDIBLES SILENCED.
(Pressing AUD SIL a second time causes
the internal audible and the System to
unsilence and the message AUDIBLES
UNSILENCED to appear on the display;
3-7
Operation
thus, pressing AUD SIL alternately silences
and unsilences the System.)
If your System has a printer, it prints a
message similar to the following:
AUD SILENCED/UNSIL. 11:01:00 DEC 31, 20XX
AUDIBLES SILENCED
Supervisories
How The System Annunciates
Supervisories
When a supervisory is detected, the
System causes the SUPERVISORY LED
on the MKB-4 to flash, the Systems
internal audible to sound, and the alphanumeric display on the MKB-4 to alternate in a
two supervisories were received (See the
explanations below).
Message 1:
002 [device type] IN SUP
Message 2:
002 [time/date] IN SUP
Message 3:
ALARMS=000
SUPERVISORIES=002
TROUBLES=000
SECURITIES=000
In addition, the System responds to

supervisories with programmed output
functions such as other audible signals.
supervisory.
supervisories received.
3-8

to the following:
SUPERV 1-1 11:59:59 DEC 31, 20XX
In the preceding message, SUPERV

supervisory; 1-1 is the device address; #1
is the number of the supervisory in the list
of supervisories; [custom message] is a
custom message entered using the CSG-M
Custom Software Generator (See the CSG-M
Programming Manual, P/N 315-090381);
[device type] is the type of device which
reported the supervisory.
Viewing the List of Supervisories

To see the supervisory list when there is
more than one supervisory, press NEXT on
the MKB-4 (the System displays the most
recent supervisory first).
How to Block Acknowledge a

Supervisory (NFPA 72 Local, Municipal
Tie, and Remote Station)
1. Note the specific location of the
supervisories by using the procedures
described above.
3. Press SUPV ACK to acknowledge all
supervisories. The System displays the
following message:
ALL SUPERVISORIES ACKNOWLEDGED.

the following message:
ACK SUPERVISORY 11:59:59 DEC 31,20XX
ALL SUPERVISORIES ACKNOWLEDGED
5. If you press SUPV ACK again, the

System displays ALL SUPERVISORIES
ACKNOWLEDGED.
The SUPERVISORY LED glows steadily
to indicate that all supervisories are
acknowledged. If there are no troubles or
security conditions in the System, the
audible pulses.
Operation
How to Individually Acknowledge a

Supervisory (NFPA 72 Proprietary, UL
1076)
1. Press SUPV ACK. The System
acknowledges the supervisory displayed
and then displays the next
unacknowledged supervisory.
If your system has a printer, it prints an
acknowledgment message similar to the
following:
ACK SUPERV 1-5 12:01:28 DEC 3,20XX
Note that the acknowledgment message

includes the term ACK to indicate this
supervisory was acknowledged.
2. Continue acknowledging supervisories
as explained above until the System
displays the following message: ALL
SUPERVISORIES ACKNOWLEDGED.
The SUPERVISORY LED glows steadily
to indicate that all supervisories are
acknowledged. If there are no troubles or
security conditions still in the System, the
audible pulses.
ACK SUPERVISORY 12:05:44 DEC 3,20XX
Troubles
How The System Annunciates Troubles
When a trouble is detected, the System
causes the TROUBLE LED on the MKB-4
to flash, the Systems internal audible to
sound, and the alphanumeric display on the
MKB-4 to alternate in a sequence among
the three messages shown below. This
example assumes that two troubles were
received (See the explanations below).
Message 2:
1-001 [device type]
002 [time/date] IN TBL
Message 3:
ALARMS=000
SUPERVISORIES=000
TROUBLES=002
SECURITIES=000
In addition, the System responds to

troubles with programmed output functions.
trouble.
troubles received.
to the following:
TROUBLE IN 1-1 11:59:59 DEC 31, 20XX
#1 [custom message] [trouble type], [device type]
In the above printed message, TROUBLE

trouble; 1-1 is the device address; and #1 is
the number of troubles in the list of troubles;
[custom message] is a custom message
entered using the CSG-M Custom Software
Generator (See the CSG-M Programming
Manual, P/N 315- 090381); [trouble type]
is the type of trouble which reported;
[device type] is the type of device in
trouble.
Viewing The List of Troubles

To see the trouble list when there is more
than one trouble, press NEXT on the
MKB-4 (the System displays the most
recent trouble first).
Message 1:
002 [trouble type] IN TBL
3-9
Operation
How to Block Acknowledge a Trouble

(NFPA 72 Local, Municipal Tie, and
Remote Station)
1. Note the specific location of the
trouble(s) by using the procedures
described above.
3. Press TRBL ACK to acknowledge all
troubles. The System displays the
following message: ALL TROUBLES
ACKNOWLEDGED.
ACK TROUBLE 11:59:59 DEC 31, 20XX
ALL TROUBLES ACKNOWLEDGED
5. If you press TRBL ACK again, the

System displays
ALL TROUBLES ACKNOWLEDGED.
The TROUBLE LED glows steadily to indicate that all troubles are acknowledged.
If there are no security conditions in the
System, the internal audible goes silent;
if any security conditions still exist, the
internal audible pulses.
The TROUBLE LED glows steadily to

indicate that all troubles are acknowledged. If there are no security conditions
still in the System, the internal audible
goes silent; if any of those conditions still
exist, the internal audible pulses.
ACK TROUBLE 12:05:44 DEC 31, 20XX
Security
How The System Annunciates Security
Conditions
When a security condition is detected, the
System causes the SECURITY LED on the
MKB-4 to flash, the Systems internal
audible to sound, and the alphanumeric
display on the MKB-4 to alternate in a
two security conditions were received (See
the explanations below the messages).
Message 1:
002 [device type] IN SEC

Trouble (NFPA 72 Proprietary, UL 1076)
1. Press TRBL ACK. The System
acknowledges the trouble displayed and
then displays the next unacknowledged
trouble.
If your System has a printer, it prints an
following:
ACK TROUBLE 1-5 12:01:28 DEC 31,20XX
#2 [custom message], [trouble type],
[device type]

trouble was acknowledged.
2. Continue acknowledging troubles as
explained above until the System
displays the following message:
ALL TROUBLES ACKNOWLEDGED.
3-10
Message 2:
002 [time/date] IN SEC
Message 3:
ALARMS=000
TROUBLES=000
SUPERVISORIES=000
SECURITIES=002
In addition, the System responds to security

conditions with programmed output functions.
security condition.
security conditions received.
Operation
reports the total number of alarms, supervisories, troubles, and security conditions.
to the following:
SECURITY IN 1-1 11:59:59 DEC 31, 20XX
In the preceding printed message, SECURITY indicates that the type of occurrence
is a security condition; 1-1 is the device
address; #1 is the number of the security
condition in the list of security conditions;
[custom message] is a custom message
entered using the CSG-M Custom Software
Generator (See the CSG-M Programming
Manual, P/N 315-090381); [device type] is
the type of device which reported the
security condition.

ACK SECURITY 12:05:44 DEC 31, 20XX
ALL SECURITY CONDITIONS ACKNOWLEDGED
Reset Procedures
Hard Reset
Other terms for Hard Reset are Power-up,
Initialization, and Cold Reset.
Applying power to the System performs a
Hard Reset which initializes (starts) the
entire system.
What Is Lost:
Alarms, supervisories, troubles, security
conditions
Any user entries such as time and date
Viewing the List of Security Conditions
Arm/disarm
To see the security condition list when there

is more than one security condition, press
NEXT on the MKB-4 (the System displays
the most recent security condition first).
Manual sensitivity adjustment

Security Condition (UL 1076)
1. Press SEC ACK. The System
acknowledges the security condition
displayed and then displays the next
unacknowledged security condition.
If your System has a printer, it prints an
following:
ACK SECURITY 1-5 12:01:28 DEC 3,20XX

security condition was acknowledged.
2. Continue acknowledging security
conditions as explained above until the
System displays the following message:
ALL SECURITY CONDITIONS
ACKNOWLEDGED.
The SECURITY LED glows steadily to
indicate that all security conditions are
acknowledged, and the internal audible
goes silent.
Time-based control until time is reset

What Is Not Lost:
CSG-M program
Soft Reset
To perform a Soft Reset, press RESET on
the MKB-4 (Refer to Figure 32, page 3-4).
Soft reset does not work until you acknowledge all alarms, supervisories, troubles,
and security conditions and silence the
System.
What Is Lost:
Alarms, supervisories, troubles, security
conditions
Arm/disarm (unless option disabled by
CSG-M)
What Is Not Lost:
Any user entries such as time and date.
Arm/disarm (when enabled by CSG-M)
CSG-M program
Manual sensitivity adjustment
Time-based control
3-11
Operation
If you press RESET before acknowledging
all conditions and silencing the audible
alarms, the display shows a message
similar to the following:
ALARMS NOT ALL ACKNOWLEDGED YET
(or)
SUPERVISORY NOT ALL ACKNOWLEDGED YET
(or)
TROUBLES NOT ALL ACKNOWLEDGED YET
(or)
SECURITY NOT ALL ACKNOWLEDGED YET
(or)
AUDIBLES NOT ALL SILENCED YET
If your System has a printer, it prints a

message similar to the following and adds
SYSTEM NOT RESET on the bottom line:
RESET 0:1 1:58 Jul 03,20XX
Not All Acknowledged Yet. System Not
Reset.
When the System performs a Soft Reset,

the display shows the following message:
SYSTEM RESET
The System then returns to Normal mode

and the display shows the following:
11:59:59 DEC 31, 20XX
[custom System message]
SYSTEM
NORMAL
If your System has a printer, it prints the

following message:
SYSTEM RESET
If the System is already in Normal mode

when you press RESET, it displays
SYSTEM ALREADY NORMAL
and does not reset.
3-12
Using The MKB

Panel in Global Mode
The Global MKB Keyboard/Annunciator
Panel operates the same as described
in Using The MKB Keyboard/Annunciator
Panel Local Mode, except as noted below.
Limitations/Restrictions
As in all networked MXL Systems, the
self-restoring trouble option is not
allowed in any MXL.
An MXL still may only contain a maximum of 4 supervised MKBs. This can be
a mix of local and global MKBs.
BLOCK ACK must be enabled in the
CSG-M.
The maximum number of supervised
Global MKBs is 10.
The maximum number of Global Printers
is 2 (not TSP-40s).
Global MKB Display Format

In order to insert the XNET node information and provide an indication of the number
of events in the System, some of the
characters in the first and second lines
have been lost.
NN = NODE # (1 - 64)
MMM = MODULE # (1 - 253)
DDD = DEVICE # (1 - 254)
ALARM
The 3 event displays are formatted as
follows for an alarm condition:
NN:MMM-DDD [custom message]
ACK
1 [time/date]
IN ALR
ACK
1 [device type]
IN ALR
ALARMS=1
TROUBLES=0
SUPERVISORY=0
SECURITY=0
Operation
SUPERVISORY
follows for a supervisory condition:
ACK
1 [time/date]
IN SUP
ACK
1 [device type]
IN SUP
ALARMS=0
TROUBLES=0
SUPERVISORY=1
SECURITY=0
TROUBLE
follows for a trouble condition:
ACK
23 [trouble type]
IN TRB
ACK
23 [time/date]
IN TRB
ALARMS=0
TROUBLES=23
SUPERVISORY=0
SECURITY=0
Global Keypad Operation

BLOCK ACK
Global block acknowledgment operates as
in a standalone MXL, but with global scope.
Events for the queue acknowledge System
wide (all nodes).
Pressing a global BLOCK ACK key results
in a broadcast XNET message to all nodes
to acknowledge all events in that queue.
Panels process the event just as if the key
press had occurred at one of its MKBs. A
success code (or error code) is sent to the
NODE that initiated the global acknowledge.
An acknowledgment message is displayed
and printed (and the appropriate LED is
updated) when the MXL determines all
events at that level have been acknowledged (System wide). The time/date stamp
of an event is used to determine the true
state of the System.
SECURITY
follows for a security condition:
LEDs are not updated unless all nodes

confirm the acknowledgment has been
successfully executed.

ACK
2 [time/date]
IN SEC
AUD SILENCE
This key is NOT a toggle as in a local
mode. If silenceable audibles are active
anywhere in the System, the LED flashes.

ACK
2 [device type]
IN SEC
ALARMS=0
TROUBLES=0
SUPERVISORY=0
SECURITY=2
Leading zeros are not included in addresses and counts.

Additional data causes a three character
shift right, resulting in the loss of three
characters from the displayed message.
Additional data also causes a two character
shift to the right, resulting in the loss of two
characters of the device or trouble type.
The System queue totals are over 10,000
events. This expands the event number fields
to 5 digits from 3. The order of these events
is as follows:
Queue priority (Alarm, Supervisory,
Trouble, Security).
Time and date of event (newest first).
If the two previous items are identical,
the lower node number takes priority.
When the global AUD SILENCE key is

pressed with any/all audibles in the System
unsilenced, a global silence command is
issued. The command is processed in the
nodes as if a local audible silence had been
requested.
Command preprocessing is in place to
prevent silenceable audibles from getting
out of sync (some systems on, some
systems off) on a System basis. No
audibles will be silenced unless all can be
silenced. However, in cases where local
control is enabled, this may be unavoidable.
An error code (or success via a silence
event message) allows the global MKB to
keep up to date as to true System status. If
any panel reports an error, the display
status remains unchanged.
When the global AUD SILENCE key is
pressed with all audibles in the System
silenced, a global unsilence command is
issued. The command is processed in the
3-13
Operation
nodes as if a local audible unsilence had
been requested. An error code (or success
via a silence event message) allows the
global MKB to keep up to date as to true
System status. If any panel reports an
error, the display status changes since
some audibles have been unsilenced.
RESET
When the global reset key is pressed, each
node is tested. If all nodes meet the
conditions required for reset, the reset
command is sent and executed. Otherwise,
the corresponding error message is displayed.
Using The Menu
The menu gives you wide control of the

MXL-IQ System. You may use the menu no
matter what mode the System is in.
The discussion in this section is in the
following order:
Operation of the keys on the MKB-4
Overview of the menus structure
Beginning a menu session
Introduction to each of the four menus:
- Acknowledge menu
- List menu
NEXT
This key operates the same as in the local
mode. However, it moves the user through
the System events globally in the priority
order established earlier.
- Control menu
- Test menu
- Entering your password
- Entering module and device numbers
HOLD
This key operates the same as in the local
mode.
Using the Acknowledge menu
Function Keys
These keys operates the same as in the
local MKB.
Using the Test menu
Numeric Keypad
These keys operates the same as in the
local MKB.
Using the List menu

Using the Control menu
Operation of the Keys on the MXL-IQ

Annunciator Panel
Use the numeric keypad and the directional
and command keypad when working with
the menu.
Numeric Keypad
Use the numeric keypad (keys 0 through 9)
when the System asks for a module
number, device number, password, time,
date, or other information. The display
shows each number as you press the key.
However, when you enter a password, the
System shows asterisks in place of the
digits entered.
The Command Keypad

The Command Keypad has both directional
and command keys that are used to move
through the menu and perform specific
functions. Refer to Table 18 for a description of the Command Keypad.
3-14
Operation
Overview of the Menus Structure

Press ENTER to enter the menu. The
menu then uses the first 32 spaces of the
second line of the display to communicate
with you. When you use the Acknowledge
or List menu, the menu uses both lines of the
display.
Acknowledge
Alarm
Supervisory (Supervsry)
Trouble
Security
TABLE 18
COMMAND KEYPAD
Key Purpose
| on the display (unless entering a number).
Select the item to the left of what is flashing

Select the item to the right of what is
} flashing on the display (unless entering a

number).
~
ENTER
Go back to the previous item.

Press to select the item on which the cursor
is flashing. After typing in numbers, press
If you are in the menu and do not depress a

numeric or arrow key at any time during a 1
minute period, the System returns to the
previous item.
The five Main Menu items and their subitems
for Revision 6.0 and higher follow; the
shortened terms used in the menu itself are
in parentheses:
List1
Status
Alarm
Trouble
Security
Sensitivity (Senstvty)
Voltages
- Analog
- Threshold
- Sensitivity
Temp
Module type (Mod type)
Device type (Dev type)
Message
Software version
(SW version)
Output States
Device Usages
Node Address
Analaser
- Smoke-lev
- Flow-lev
- Trip-pts
Percent/ft
- Senstvty
- Pre-alarm
- Analog
ASD apps
1
You can generate a

printed report or listing
for every item in the List
menu except Node
Address; see the
discussion under LIST
Menu.
Control
Reset
- Hi_3
- Hi_2
- Hi_1
- Norm
- Low_1
- Low_2
- Low_3
Arm/disarm (Arm/dis)
- Arm
- Disarm
Output on/off
- Arm
- Disarm
- Energize
- De-Energize
Loop Arm
Loop Disarm
Netlink Request
Analaser
- Alarm_Trip
- Flow_Trip
Percent/Ft
- Sensitivity
(Senstvty)
- Pre_alarm
Change_Apps
Test
Set time
Ground fault (Gnd_flt)
- Main
Power2
- Main
- Voltage
- Current
Lamp test
- LEDs
- Display
Device LED
MOI_Lamp_Test
X-Network
M-Network
Override
Det_cleaned
Event_log
- Alrm_only
- Trbl_only
- Superv_only
- Security_only
- All_events
- Hist_Ctrl
- Hist_Erase
Pyro_diags
Pre_alarm
ASD_Devices
Summarize
Manual_Activate
2
You can generate a

printed report for this
item; see the discussion
under TEST Menu.
ENTER to complete the entry.
HELP
Press to display a one-line message.
PRINT
Press to begin printing various lists and

reports.
FORM
FEED
Press to advance the paper in the printer.
CLEAR
Press to cancel printouts begun by pressing

PRINT. The System will print:
This listing prematurely terminated.
Walktest
System_wAUD
Loop_wAUD
Zone_wAUD
System_SIL
Loop_SIL
Zone_SIL
Cancel
Extend
3-15
Operation
Beginning a Menu Session

When you first press ENTER to begin a
menu session, the second line of the
display shows the four Main Menu items:
ACKNOWLEDGE
TEST
LIST
CONTROL
The A in Acknowledge is blinking. Select

Acknowledge by pressing ENTER while the
A is blinking.
Use the Left and Right arrow keys to move
around in this four-item menu.
LIST
CONTROL
TEST
For help in understanding what the List

function does, press HELP when the L in
LIST is blinking. The System displays:
TO LIST SYSTEM, DEVICE, CSGM INFO
Use this function to list information on the

System and its devices.
To return to the Main Menu display, press
HELP again:
ACKNOWLEDGE
LIST
CONTROL
TEST
To end a menu session and return to the

Main Menu or to leave the menu at any
time, press the Up arrow key to go backward one menu each time.
We discuss the List menu in detail beginning

on page 3-22.
Introduction to the Acknowledge Menu
Introduction to the Control Menu
The Main Menu, displayed when you press

ENTER to begin a menu session, lists the
four main items in the menu:
ACKNOWLEDGE
TEST
LIST
CONTROL
For help in understanding what the Acknowledge function does, press HELP when the
A in ACKNOWLEDGE is blinking. The
System displays:
TO ACKNOWLEDGE INDIVIDUALLY
Use this menu function to acknowledge

alarms, supervisories, troubles, and
security conditions individually.
HELP again:
ACKNOWLEDGE
TEST
LIST
CONTROL
We discuss the Acknowledge menu in

detail beginning on page 3-18.
Introduction to the List Menu

To move to LIST on the Main Menu, press
the Right arrow key once; the L in LIST
begins blinking:
3-16
ACKNOWLEDGE
To move to CONTROL on the Main Menu,

press the Right arrow key twice from
ACKNOWLEDGE; the C in CONTROL
begins blinking:
ACKNOWLEDGE
LIST
CONTROL
TEST
For help in understanding what the Control

function does, press HELP while the C in
CONTROL is blinking. The System displays:
TO MODIFY DATA FOR OPERATION
Use the Control function to reset the System

and to change the settings of various devices.
HELP again:
ACKNOWLEDGE
LIST
CONTROL
TEST
We discuss the Control menu in detail

beginning on page 3-36.
Introduction to the Test Menu

To move to TEST, press the Right arrow
key three times from ACKNOWLEDGE; the
T in TEST begins blinking:
ACKNOWLEDGE
LIST
CONTROL
TEST
For help in understanding what the Test

function does, press HELP while the T in
TEST is blinking. The System displays:
Operation
TO TEST SYSTEM, LOOP & DEVICE
Use this function to test the System, its

loops, and its devices, including ground
fault, battery voltage and current, and the
LEDs.
HELP again:
ACKNOWLEDGE
LIST
CONTROL
TEST
We discuss the Test menu in detail beginning on page 3-42.
Entering Your Password

If you select CONTROL, TEST, or WALKTEST, the System asks for your password:
ENTER YOUR PASSWORD:
The System gives you three chances to

enter an acceptable password before it
returns you to the Main Menu.
If the System accepts your password, it
displays the Control, Test, or Walktest
menu. We discuss those menus later in this
section.
Entering a Module Number and Device

Number
The System asks you to supply a module
number or device number, or both, during
certain functions described in the pages
that follow. Below is a summary of the
procedures involved.
NOTE:
The terms module number and

module address are used interchangeably in this manual.
Entering a Module Number

The System displays
If you press HELP, the System explains

this function; press HELP again to return to
the previous display.
TYPE IN MODULE NUMBER:
Type your (1-5 digit) password, using the

numeric keypad. The System shows an
asterisk for each digit that you type. (Use
the Left arrow key to erase an error.)
If you press HELP at this point, the System

displays the following explanation:
When you have typed the entire password,

press ENTER. If your password does not
match a password stored in the System,
the System briefly displays the following
message and then returns you to the first
password display:
ACCESS DENIED
If your password level is not high enough to

use the Test functions, the System briefly
displays the following message and then
returns you to the first password display:
3 DIGIT MODULE NO., PRESS <ENTER>
Press HELP again to return to the previous

display. Type all three digits, including
leading zeros, and press ENTER.
When you type the module number, use
the Left arrow key as a backspace key to
erase errors.
Entering a Device Number with the

Module Number
The System displays
TYPE IN THE DEVICE NUMBER:
PASSWORD LEVEL NOT HIGH ENOUGH
(If you press HELP at this point, the System

displays the following explanation:
PASSWORD LEVELS
Rev 5.0 and Above
Highest
Test
Z
Control
Lowest
Walktest
Below Rev 5.0
Highest
Y
Lowest
Walktest
Test
Control
3 DIGIT MODULE 3 DIGIT DEVICE

display. Type all of the digits, including
leading zeros, and press ENTER.)
3-17
Operation
When you type the module number and
the device number, use the Left arrow
key as a backspace key to erase errors.
If All Alarms Are Acknowledged:

If all the alarms are acknowledged, the
System displays the following message and
then returns you to the Acknowledge menu.
ACKNOWLEDGE Menu
The Acknowledge menu has four items

from which to choose; the shortened
terms used in the menu itself are in
parentheses:
ALARM
SUPERVISORY (SUPERVSRY)
TROUBLE
SECURITY
If There Is an Unacknowledged Alarm:

If there is at least one unacknowledged
alarm, the menu shows the most recent
unacknowledged alarm on both lines of the
display, as in the following display:
Use this menu to individually acknowledge fire alarms, supervisories, troubles,

and security conditions.

007 [device type] IN ALR
Entering the Acknowledge Menu
In the above display, 29 is the module

number, 041 is the device number, the
message on the first line is the custom
message for the device at that location, 007
indicates that this is the seventh alarm,
[device type] indicates the type of device
in alarm, and IN ALR indicates that this is a
fire alarm.
Select ACKNOWLEDGE from the Main

Menu by pressing ENTER while the A in
ACKNOWLEDGE is blinking. The System
displays the first Acknowledge menu (the
A in ALARM is blinking):
ACKNOWLEDGE: ALARM SUPERVISRY
NOTE:
To end a menu session and

return to the Main Menu or to
leave the menu at any time,
press the Up arrow key to go
backward one menu each time.
Acknowledge: Alarm
Use this function to individually acknowledge fire alarms.
Press ENTER when the A in ALARM is
blinking to select ACKNOWLEDGE ALARM:
If There Is No Alarm:
If there is no current alarm, the System
briefly displays the following message
and then returns you to the Acknowledge
menu:
NO ALARM EXISTS
(If your System has a printer, it prints the

above message as well.)
3-18

(Press HELP if you want information on

what to do. The System displays:
PRESS ENTER TO ACK. PRESS NEXT
TO SKIP.

display.)
Press ENTER to acknowledge the alarm
shown.
The System prints a message similar to the
following and removes that alarm from the
unacknowledged alarm list:
ACK ALARM 29-041 16:11:41 Aug 28,20XX
In the above message, the time and date

are the time and date that the alarm was
acknowledged and 29-041 is the address.
The System then displays the next alarm to
acknowledge.
To skip an alarm shown, press NEXT. The
System displays the next alarm in the
series. When the System has displayed all
Operation
of the unacknowledged alarms, it returns to
the first Acknowledge menu:
(To end a menu session and return to the

time, press the Up arrow key to go backward one menu each time.)
If There Is An Unacknowledged Supervisory:

The System does not let you acknowledge
supervisory conditions if there are any
unacknowledged alarms. If there is at least
one unacknowledged alarm, the System
briefly displays the following message and
then returns you to the Acknowledge menu:
ALARM NOT ALL ACKNOWLEDGED YET
Acknowledge: Supervsry
Use this function to individually acknowledge supervisories.
Select ALARM and follow the instructions

in ACKNOWLEDGE ALARM above.

displays:

Press the Right arrow key once to cause the

S in SUPERVISRY to blink.
(If you press HELP at this time, the System
explains the Acknowledge Supervisory
function:
TO ACK SUPERVISORY INDIVIDUALLY
Press HELP again to return to the ACKNOWLEDGE: ALARM SUPERVISRY

display.)
Press ENTER while the S is blinking to
select SUPERVISRY.
If There Is No Supervisory:
If there is no supervisory to acknowledge,
the System briefly displays the following
message and then returns you to the Acknowledge menu:
NO SUPERVISORY EXISTS

If All Supervisories Are Acknowledged:
If all supervisories are acknowledged, the
System briefly displays the following
message and then returns you to the
Acknowledge menu:
After you acknowledge all alarms, the

System allows you to acknowledge
supervisories. If there is at least one
unacknowledged supervisory, the menu
shows the most recent unacknowledged
supervisory on both lines of the display, as
in the following display:
012 [device type]
IN SUP
In the preceding display, 32 is the module

indicates that this is the twelfth supervisory,
[device type] indicates the type of device
causing the supervisory, and IN SUP identifies the item as an off-normal supervisory.
TO SKIP

display.)
Press ENTER to acknowledge the supervisory shown. The System prints a message
similar to the following and removes that
supervisory from the unacknowledged
supervisory list:
ACK SUPERV 32-045 16:11:44 Aug 2,20XX

are the time and date the supervisory was
3-19
Operation
The System then displays the next supervisory to acknowledge.
To skip a supervisory, press NEXT. The
System displays the next supervisory in the
series. When the System has displayed all
of the unacknowledged supervisories, the
System returns to the acknowledge menu
on the second line of the display.
time, press the Up arrow key to go backward
one menu each time.)
Acknowledge: Trouble
Use this function to individually acknowledge troubles.
displays the first Acknowledge menu:
Press the Right arrow key twice. The

System displays the Acknowledge menu
with T in TROUBLE blinking:
ACKNOWLEDGE: SUPERVISRY TROUBLE

explains the Acknowledge Trouble function:
TO ACK TROUBLE INDIVIDUALLY
Press HELP again to return to the acknowledge menu.)

Press ENTER while the T is blinking to select
Trouble.

If There Is An Unacknowledged Trouble:
troubles if there are any unacknowledged
fire alarms or supervisories. Follow the
instructions above to acknowledge them.
After you acknowledge all fire alarms and
supervisories, the System allows you to
acknowledge troubles. If there is at least
one unacknowledged trouble, the System
shows the most recent unacknowledged
trouble on both lines of the display, as in
the following display:
018 [trouble type]
IN TBL

message for that device, 018 indicates that
this is the eighteenth trouble, [trouble
type] indicates the type of trouble, and IN
TBL identifies the event as the occurrence
of a trouble.
TO SKIP.

display.)
If There Is No Trouble:
If there is no trouble to acknowledge, the
System briefly displays the following
message and returns you to the acknowledge menu:
Press ENTER to acknowledge the trouble

shown. The System prints a message
similar to the following message and
removes that trouble from the unacknowledged trouble list:
NO TROUBLE EXISTS
ACK TROUBLE 36-050 16:11:44 Aug 8, 20XX

#18 [custom message], [trouble type]
[device type]

3-20
If All Troubles Are Acknowledged:

If all the troubles are acknowledged, the
System displays the following message and
returns you to the Acknowledge menu:
Operation
are the time and date that the condition was
The System then displays the next trouble
to acknowledge.
If All Security Conditions Are Acknowledged:

If all security conditions are acknowledged,
the System displays the following message
and returns you to the Acknowledge menu:
ALL SECURITIES ARE ACKNOWLEDGED
When the System has displayed all of the

unacknowledged troubles, it returns to the
Acknowledge menu.


Main Menu or to leave the menu at any time,
press the Up arrow key to go backward one
menu each time.)
If There Is An Unacknowledged Security

Condition:
security conditions if there are any unacknowledged alarms, supervisories, or
troubles.
Acknowledge: Security
Use this function to individually acknowledge security conditions.
displays the first Acknowledge menu:
Press the Right arrow key three times. The

System displays the second Acknowledge
menu, with the S in SECURITY blinking:
ACKNOWLEDGE: TROUBLE SECURITY

explains the Acknowledge Security function:
TO ACK SECURITY INDIVIDUALLY
Press HELP again to return to the Acknowledge menu.)

Press ENTER while the S is blinking to
select Security.
If There Is No Security Condition to Acknowledge:
If there is no Security condition to acknowledge, the System briefly displays the
following message and then returns you to
the Acknowledge menu:
NO SECURITY EXISTS

If there is at least one unacknowledged

alarm, the System briefly displays the
following message and then returns you to
the Acknowledge menu:
ALARMS NOT ALL ACKNOWLEDGED YET

Follow the instructions above to acknowledge any unacknowledged alarms,
supervisories, and troubles.
After you acknowledge all fire alarms,
supervisories, and troubles, the System
allows you to acknowledge security conditions. If there is at least one unacknowledged
security condition, the System displays the
most recent unacknowledged security
condition:
005 [device type]
IN SEC

indicates that this is the fifth security
condition, [device type] indicates the type
of device causing the security condition, and
IN SEC identifies this as an off-normal
security condition.
TO SKIP.

display.)
3-21
Operation
Press ENTER to acknowledge the security
condition shown. The System prints a
message similar to the following message
and removes that security condition from
the unacknowledged security list:
Software version (SW version)
ACK SECURITY 42-058 16:11:44 Aug 8,20XX

Analaser
Output states
Device usages
Node address
Percent/ft
ASD_apps

given are the time and date when the
security condition was acknowledged, and
42-058 is the address.
The System then displays the next security
report to acknowledge.
To skip a security condition, press NEXT.
The System displays the next security
condition in the series. When the System
has displayed all of the unacknowledged
security conditions, it returns to the Acknowledge menu.
menu each time.)
LIST Menu
The List menu has eighteen items from

which to choose; the shortened terms used
in the menu are in parentheses.
You can generate a printed list or report for
every item on the List menu except Node
Address. See the discussion for each item
that follows.
Status
Alarm
Use the List menu to learn the following

information:
Status of the System
Alarm information
Supervisory information
Trouble information
Security information
Detector sensitivity
Detector voltage
Analog
Threshold (Thresh)
Sensitivity (Sens)
Temperature of FP-11 or FPT-11
Type of module
Type of device
Custom message of the given
address
Version of the System software
Output states
Device usages
Panel's X-Network node address
Percent per foot obscuration
Sensitivity
Pre-alarm
Analog
Device application (ASD setting)
Trouble
Security
Voltages
Temp
Module type (Mod type)
Entering the List Menu

From the Main Menu, use the Left or Right
arrow key to cause the L in List to blink.
explains the List function:
TO LIST SYSTEM, DEVICE, CSGM INFO
Device type (Dev type)

Message
3-22
Press HELP again to return to the Main

Menu.
Operation
Press ENTER to select LIST. The System
displays the first List menu, with the S in
STATUS blinking:
LIST: STATUS ALARM SUPERVSRY

In the above printed message, there are

two alarms, both of them acknowledged, no
supervisory conditions, 30 trouble conditions, all acknowledged, and no security
conditions.
menu each time.)
List: Alarm
List: Status
The List Status function shows you the
number of acknowledged and unacknowledged alarms, supervisories, troubles, and
security conditions, in that order.
From the List menu, use the Right or Left
arrow keys to cause the S in STATUS to
blink.
explains the List Status function:
The List Alarm function shows you all the

fire alarms currently in the System in the
order they occurred.
From the List menu, use the Left or Right
arrow key to cause the A in ALARM to
begin blinking.
explains the List Alarm function:
SHOW INDIVIDUAL ALARM STATUS
SHOW NUMBER OF ACKED & UNACKED
Press HELP again to return to the List

menu.
menu.)
When you press ENTER to select List
Status, the display first shows the total
number of alarms and the number of
acknowledged alarms:
2 ALARM
2 ALARM ACK
Press ENTER to select ALARM and display

alarm information on the MKB-4 display.
If There Is No Fire Alarm:
If there is no fire alarm, the System briefly
returns you to the List menu:
NO ALARM EXISTS
To view, in order, the status of

supervisories, troubles, and security
conditions, press NEXT.
After the Security display, the System
returns to the List menu.
If There Is a Fire Alarm:

If there is at least one fire alarm, the System
shows the most recent alarm, alternating
between the following two displays:
To make a printed list of current status,

press PRINT when the S in STATUS is
blinking. The System will print a listing
similar to the following:

002 [device type]
IN ALR
System Status at 11:02:26 Jul 01, 20XX:

2 ALARM 2 ALARM ACK 0 SUPERV
0 SUPERV ACK
30 TROUBLE 30 TROUBLE ACK
0 SECURITY 0 SECURITY ACK

002 [time/date]
IN ALR
Press NEXT to show the two displays for the

previous alarm in the sequence. (Pressing
HOLD freezes a display for as long as you
keep HOLD depressed.)
3-23
Operation
When the System has shown all current fire
alarms, it returns to the List menu.
alternating between the following two

displays:
To obtain a full printed list of alarms in

the following formatone item for each
current alarmpress PRINT when the A in
ALARM is blinking.

002 [device type]
IN SUP
1-001 [custom-message]
002 [time/date]
IN SUP
Listing of all Alarm at 14:35:20 Oct 09,20XX:

ALARM 1-5 14:34:22 Oct 09,20XX #1
[custom message], [device type]
In the above listing, 1-5 is the address of

the device in alarm, the time is the time the
device went into alarm, #1 is the number of
this alarm in the current list, [custom
message] is the custom message for the
device in alarm, and [device type] is the
type of device in alarm.
menu each time.)
List: Supervisory
The List Supervisory function shows you all
the supervisories currently in the System in
the order they occurred.
From the List menu, use the Left or Right
arrow key to cause the S in SUPERVSRY
to blink.
explains the List Supervisory function:
SHOW INDIVIDUAL SUPERVISORY
When the System has shown all current

supervisories, it returns to the List menu.
To obtain a full printed list of
supervisories in the following formatone
item for each current supervisorypress
PRINT when the S in SUPERVISORY is
blinking.
Listing of all Supervsry at 14:35:20 Oct 09,20XX:
SUPERV IN 32-45 14:34:22 Oct 09, 20XX
In the preceding listing, 32-45 is the address of the device in supervisory, #7 is the
number of the supervisory in the current list,
[custom message] is the custom message
for the device in supervisory, and [device
type] is the type of device in supervisory.
menu each time.)

menu.)
List: Trouble
Press ENTER to select SUPERVSRY and

display supervisory information on the
MKB-4 display.
The List Trouble function shows you all the

troubles currently in the System in the order
they occurred.
If There Is No Supervisory:
If there is no supervisory, the System briefly
returns you to the List menu:
3-24

previous supervisory in the sequence.
(Pressing HOLD freezes a display for as
long as you keep HOLD depressed.)
From the List menu, use the left or right

arrow key three times to cause the T in
TROUBLE to blink.
explains the List Trouble function:
NO SUPERVISORY EXISTS
SHOW INDIVIDUAL TROUBLE STATUS
If There Is a Supervisory:
If there is at least one supervisory, the
System shows the most recent supervisory,

menu.)
Operation
Press ENTER to select TROUBLE and
display trouble information on the MKB-4
display.
List Security Conditions
If There Is No Trouble:
If there is no trouble, the System briefly
returns to the List menu:

arrow key to cause the S in SECURITY to
blink.
NO TROUBLE EXISTS.
The List Security function shows you all the

security conditions currently in the System in
the order they occurred.

explains the List Security function:
SHOW INDIVIDUAL SECURITY STATUS
If There Is a Trouble:
If there is at least one trouble, the System
shows the most recent trouble, alternating
between the following two displays:
002 [trouble type]
IN TBL
1-001 [device type]

002 [time/date]
IN TBL

previous trouble in the sequence. (Pressing
HOLD freezes a display for as long as you
keep HOLD depressed.)
troubles, it returns to the List menu.
To obtain a full printed list of troubles in
the following formatone item for each
current troublepress PRINT when the T
in TROUBLE is blinking.
Listing of all Trouble at 14:35:20 Oct 09, 20XX:
TROUBLE IN 29-41 14:34:22 Oct 09, 20XX
#7 [custom message],[trouble type],
[device type]

menu.)
Press ENTER to select SECURITY and
display security information on the MKB-4
display.
If There Is No Security Condition:
If there is no security condition, the System
briefly displays the following message and
then returns you to the List menu:
NO SECURITY EXISTS
If There Is a Security Condition:

If there is at least one security condition,
the System shows the most recent security
condition, alternating between the following
two displays:
002 [device type]
IN SEC

002 [time/date]
IN SEC
In the above listing 29-41 is the address of

the device in trouble, the time tells when the
device went into trouble, #7 is the number
of this trouble in the current list, [custom
message] is the custom message for the
device in trouble, [trouble type] is the type
of trouble, and [device type] is the type of
device in trouble.

previous security condition in the sequence.
(Pressing HOLD freezes a display for as
long as you keep HOLD depressed.)

menu each time.)
To obtain a full printed list of security

conditions in the following format one
item for each current security condition
press PRINT when the S in SECURITY is
blinking.

security conditions, it returns to the List
menu.
3-25
Operation
Listing of all Security at 14:35:20 Oct 09,20XX:
SECURTY IN 29-42 14:34:22 Oct 09,20XX
In the above listing 29-42 is the address of

the device causing the security condition, the
time when the device caused the security
condition, #7 is the number of this security
condition, [custom message] is the custom
message for the device causing the security
condition, and [device type] is the type of
device causing the security condition.
Press NEXT to display the address and

sensitivity setting of each succeeding
smoke detector. When the System has
shown the sensitivity settings of all smoke
detectors on that analog loop, it returns to
the List menu.
To leave the List Sensitivity menu without
going through the entire analog loop, press
the Up arrow key. The System displays the
List menu.
To end a menu session and return to the

menu each time.
Print the Sensitivity Setting of All Smoke

Detectors Assigned to a Specified Module
Press PRINT when the S in SENSTVTY is
blinking. The System then asks for a
module number.
List: Sensitivity Settings
TYPE IN MODULE NUMBER: [module number]
Use List Sensitivity to show sensitivity

setting of individual smoke detectors on
analog loops.
From the List menu use the left or right
arrow key to cause the S in SENSTVTY to
start blinking:
LIST: TROUBLE SECURITY SENSTVTY
Type the three-digit module number and

press ENTER. (Enter all leading zeros.)
The System prints the sensitivity settings
(Hi_3, Hi_2, Hi_1, Norm, Low_1, Low_2 or
Low_3, or ... if there is no smoke detector) of
all the devices assigned to the analog loop.
Sensitivities for module 1

displays:
SHOW DETECTOR SENSITIVITIES
1- HI_3
6- ...
11- NORM
2- ... 3- NORM 4- ... 5- ...

7- ... 8- ... 9- ... 10- ...
12- ... 13- ... 14- ... 15- LOW1
NOTE: You cannot print the sensitivity

setting of a single smoke detector.
Note that List Sensitivity shows the sensitivity of smoke detectors only. Press HELP
again to return to the List menu.)
Display the Sensitivity Setting of One Device
Press ENTER to select List Sensitivity. The
System asks you for a module and device
number.
TYPE IN MODULE & DEVICE: 001-001

three-digit device number using the numeric keypad and press ENTER. (Enter all
leading zeros.)
The System displays the sensitivity setting
of the device specified (Hi_3, Hi_2, Hi_1,
Norm, Low_1, Low_2 or Low_3 ).
3-26

menu each time.)
List: Voltages
Use List Voltages to show the voltages of
initiating devices on analog loops.
From the List menu press the Left or Right
arrow key to cause the V in VOLTAGES to
start blinking:
LIST: SECURITY, SENSTVTY, VOLTAGES
Operation
displays:
If the module number entered is not an

analog loop, the System displays:
SHOW DETECTOR VOLTAGES
Not Analog Loop.
Press HELP again to return to the List menu.)
If the device address has no device assigned by CSG-M, the System displays:
Display the Voltage of One Device

Press ENTER to select List Voltages. The
System asks you for a module number and
device number. Type the three-digit module
number and three-digit device number
using the numeric keypad and press
ENTER. (Enter all leading zeros.) The
System shows the following menu for that
device (the A in ANALOG will be blinking):
No Device Assigned.
001-001 ANALOG THRESH SENS
Press ENTER to show the Analog voltage

for that device. When you ask for any
voltage, the System displays Please wait for
response until it receives a reading from
the device; if you have just reset the
System, it alternates the above message
with the message Device being initialized.
The display for Analog voltage is similar to
the following (readings are dynamic):
001-001 ANALOG2 = 2.75 VOLTS
Press ENTER to return to the previous

display. To view the Threshold or Sensitivity
voltage of any device listed, use the Right
and Left arrow keys to highlight the first
letter of the category desired and press
ENTER.
The display for Threshold voltage is similar
to the following:
001-001 THRESHOLD = 4.75 VOLTS
The display for Sensitivity voltage is similar

to the following (readings are dynamic):
001-001 SENSITIVITY = 2.62 VOLTS
When displaying sensitivities, if the device is

not a smoke detector, the System displays:
Not a Smoke Detector.
Print the Voltage of All Devices Assigned to a

Specified Module
Press PRINT when the V in Voltages is
blinking. The System asks you for a module
number. Type the three-digit module number
and press ENTER. (Enter all leading
zeros.)
002-001 Analog Thresh Sens
Press ENTER to print the Analog voltage

for all devices assigned to the module
(ND = No Device).
ANALOG VOLTAGES FOR MODULE 1
1- 2.00 2- 2.00 3- ND 4- ND 5- ND
6- ND
7- ND
8- ND 9- ND 10- ND
11- ND 12- ND 13- ND 14- ND 15- ND
To print the Threshold voltages of all the

devices for the specified module, use the
arrow keys to cause the T in THRESH to
blink and press PRINT. The System prints
those threshold voltages in a format similar to
the following (ND = No Device):
THRESHOLD VOLTAGES FOR MODULE 1
1- 4.75 2- 4.75 3- ND 4- ND 5- ND
6- ND
7- ND 10- ND 8- ND 9- ND
11- ND 12- ND 13- ND 14- ND 15- ND
Press the Up arrow key to return to the List:

Voltage Mod_type Dev_type menu.
3-27
Operation
To print the Sensitivity voltages of all the
smoke detectors for the specified module,
use the arrow keys to cause the S in SENS
to blink and press PRINT. The System
prints those sensitivity voltages in a format
similar to the following (ND = No Device, or
device not a smoke detector):
SENSITIVITY VOLTAGES FOR
1- 2.75 2- 2.62 3- ND
6- ND
7- ND
10- ND
11- ND 12- ND
13- ND
MODULE 1
4- ND 5- ND
8- ND 9- ND
14- ND 15- ND

menu each time.)
To leave the Temp menu without going

through all subaddresses, press the Up
arrow key. The System displays the List
menu.
List: Module Type

Use the List Mod_type to show the type of
a particular module.
From the List menu use the Left or Right
arrow key to cause the M in MOD TYPE to
start blinking:
LIST: VOLTAGES MOD TYPE SENSTVTY

explains this function:
SHOW THE TYPE OF MODULE
List: Temp
Use List Temp to display the current
temperature on the LCD display at the
location where the detector is installed.
arrow key to cause the T in Temp to start
blinking:
LIST: TEMP
Press ENTER to select List Temp. The

number:
Type In Module & Device:

three-digit device number using the numeric keypad and press ENTER.
If the device is not installed or is not an
FP-11 or FPT-11, the system displays
following message:
Not Applicable or No Device:

menu.)
Display the Module Type of One Module
Press ENTER when the M in MOD_ TYPE
is blinking. The System asks you for a
module number:
Type the three-digit module number using

the numeric keypad and press ENTER.
(Enter the leading zeros.) The System
displays the module type for the module
number specified:
MOD 074 TYPE: CZM4
If you press NEXT, the System displays the

module type for the next module number in
the sequence:
MOD 075 TYPE: ALD
If the device is an FP-11 or FPT-11, the

temperature is displayed in the following
format:
001-001
25 DEG C / 77 DEG F
NOTE:
If you enter a module number not

assigned in CSG-M, the System
displays:
NO MOD ASSIGNED
Press NEXT to display the temperature of

the FP-11 or FPT-11 at the next higher
address in the same loop.
3-28
With each press of NEXT, the System

continues to display module types through
Operation
number 255, the highest module number
allowed by the System. It then returns to
the List menu.
Print the Module Type and Network Address of
All Modules
Press PRINT when the M in MOD_ TYPE is
blinking to print a full list of module types
and their Network addresses. The System
prints a list similar to the following:
Listing of Module Types:
1- V7 ALD
2- V7 ALD
3- V4 CZM-4
251- V5 MKB-4
253- V1 MXL-IQ Panel
In the above display, the number following

the V (for example, V7) is the software
version number of the software installed in
the module.
meric keypad and press ENTER. (Enter all

leading zeros.) The System displays the
device type for the address specified:
004-001 TYPE: [device type]

device type for the next device in the
sequence:
004-002 TYPE: [device type]

continues to display device types until there
are no more devices for that module. The
System then returns to the List menu. To
proceed to another module, follow the
preceding instructions.

menu each time.)
Print a List of Devices Assigned to a Specified

Module
Press PRINT when the D is blinking to
select LIST DEVICE. The System asks you
for a module number:
List: Device Type
Use List Device Type to show the type of a

particular device.
arrow key to cause the D in DEV_TYPE to
start blinking:
LIST: VOLTAGES MOD TYPE DEV TYPE

displays:
SHOW THE TYPE OF DEVICE

Display the Device Type of a Specified Device
Press ENTER when the D is blinking to
select LIST DEV_TYPE.
The System asks you for a module and
device number:
TYPE IN MODULE & DEVICE:

three-digit device number using the nu-
Type only the module number and press

PRINT. (Enter all leading zeros.) The
System prints a list of all device types
assigned to the specified module in a
format similar to the following:
Listing of Device Types Module 1 (ALD):
1-TRI-60D Dual Switch Input
2-TRI-60D Dual Switch Input
4-TRI-60D Switch input + Relay
5-TRI-60 Switch Input
7-TRI-60 Switch Input
10-ID-60T-135 Thermal Detector
11-ID-60T-135 Thermal Detector
15-ID-60I Ionization Detector
16-ID-60I Ionization Detector

menu each time.)
List: Message
Use List Message to show the CSG-M
assigned custom message of a particular
device.
3-29
Operation
arrow key to cause the M in MESSAGE to
start blinking:
LIST: MOD TYPE DEV TYPE MESSAGE

displays:
SHOW MESSAGE FOR A DEVICE
Type only the module number and press

PRINT. (Enter all leading zeros.) The
System prints a list of all the custom device
messages for the specified module in a
format similar to the following:
Listing of Messages in Module 1 (ALD):
4-Conf.Rm
5-Cafeteria
6-Exec. Off. 1
7-Cmptr Rm
8-Exec. Off. 2
9-Camera Rm
10-Exec. Off. 3
11-Conf. Rm

display.)

Display the Device Message of a Specified

Device
Press ENTER when the M in MESSAGE is
blinking to select List Message.
List: Software Version

device number:

three-digit device number using the numeric keypad and press ENTER. The
System displays the message for the
address specified:
Use List Software Version to show:

1. System Custom Message
2. MXL-IQ Software Version
3. Version of CSG-M used to Create the
System
4. CSG-M File Name Installed
5. Date and Time of Installation
arrow key to cause the S in S/W_VERSION
to start blinking:
LIST: S/W VERSION STATUS

displays:
message for the next device number in the
sequence:
SHOW SOFTWARE VERSION

display.)

continues to display device messages until
there are no more devices for that module.
Display the Software Version of Your System

Software
Press ENTER when the S is blinking to
select List S/W_VERSION.
To proceed to another module, follow the

Print a List of System Messages for a Specified

Module
Press PRINT when the M in MESSAGE is
blinking to select List Message. The
System asks you for a module number:
3-30
The System displays the CSG-M assigned

System custom message:
MSG [system custom message]
Press NEXT again to display the MXL-IQ

software version:
MXL-IQ VERSION: [version number]
Operation
Press NEXT again to display the version of
CSG-M used to create this System.
CSG VERSION: [version number]
Display the Output States of One Device

Press ENTER to select List Output States.
device number.
Press NEXT again to display the CSG-M

file name installed.
SOURCE: [file name]
Press NEXT again to display the date and

time of CSG-M installation:
LOADED: [time and date]
Print the Software Version of Your System

Software
Press PRINT when the S in SW_ VERSION is blinking to select List S/
W_Version. The System prints the System
Custom Message, MXL-IQ Software
Version, Version of CSG-M Used to Create
the System, CSG-M File Name Installed,
and Date and Time of Installation:
Software Version Information at
11:35:30 Jul 01, 20XX
Installation: [system custom message]
MXL-IQ Version: 1.00
CSG Version: 6.09
Source: 05OCT00
Loaded: 16:09:35 Oct 05, 20XX

menu each time.)
List: Output States

Use List Output States to show the current
states of individual outputs in the MXL-IQ.
arrow key to cause the O in Output States
to start blinking:
LIST: OUTPUT STATES
(If you press HELP at this point, the

System displays:

leading zeros.)
The System displays the output state of the
device specified.
output state of each succeeding device.
When the System has shown the output
states of all devices at that address, it
returns to the List menu.
To leave the List output state menu without
going through all subaddresses, press the
Up arrow key. The System displays the List
menu.
Print the Device Output State of Devices
Assigned to a Specified Module
Press PRINT when the O in Output States
is blinking. The System then asks for a
module number.

The System prints the output state of all of
the devices assigned to that module.
Listing of Output States for Module 1 (ALD):
1-Auxiliary Output: OFF
2-Auxiliary Output: ON
3-Auxiliary Output: ON
4-Auxiliary Output: OFF
List: Device Usages

Use List Device Usages to show the uses
of individual devices as programmed in
CSG-M.
SHOW/PRINT OUTPUT STATES
3-31
Operation
arrow key to cause the D in DEV_USAGES
to start blinking:
Listing of Device Usages for module 1 (ALD)

1- ALARM
2- TROUBLE
3- STATUS
4- ALARM
5- TROUBLE
6- OUTPUT ONLY
LIST: DEV USAGES
List: Node Address

displays:
Use List Node Address to show the panel's

X-Net node address.
SHOW/PRINT DEVICE USAGES

arrow key to cause the N in NODE ADDRESS to start blinking:

menu.)
LIST: NODE ADDRESS
Display the Usage of One Device

Press ENTER to select List Dev_usages.
device number.
Display the Node Address

Press ENTER to select List Node Address.
The System displays the X-Net node
address for that particular MXL-IQ panel.
List: Analaser
Use List ANALASER to display operational
characteristics of the AnaLASER devices.

leading zeros.)
The System displays the use of the device
specified (i.e., Alarm, Trouble, or Status).
Press NEXT to display the address and use
of each succeeding device. When the
System has shown the uses of all devices
at that address, it returns to the List menu.
To leave the List Dev_usage menu without
going through all subaddresses, press the
Up arrow key. The System displays the List
menu.
Print the Device Usages of Devices Assigned to
a Specified Module
Press PRINT when the D in DEV_USAGES
is blinking. The System then asks for a
module number.

The System prints the uses of all of the
devices assigned to that module.
3-32
Press ENTER when the A in ANALASER is

blinking to select List ANALASER.
Use the Left or Right arrow to move to the
following selections:
ANALASER: Smoke Lev
Trip Pts
Flow Lev

displays:
DISPLAY ANALASER SMOKE LEVEL

menu.)
List Analaser Smoke_Lev
Press ENTER when the S in SMOKE_LEV
is blinking to select List ANALASER
SMOKE_LEV.
device number:
TYPE IN MODULE & DEVICE
Type the three-digit NIM-1R (ANA) module

number and three-digit ACC device address number using the numeric keypad
Operation
and press ENTER. The system displays the
smoke level for the address specified:
010-004
50%
>>!*
*<<
PRE1
The bar graph in the example above shows

the following information for the AnaLASER
device at address 010-004:
50% = 50% of full scale smoke level
!
= active trip point at 30%
*
= inactive trip point at 60% and 100%
PRE1 indicates the device is in PreAlarm 1
PRE2 and ALRM indicate the PreAlarm 2
and Alarm states, respectively. The bargraph continuously updates to reflect the
current state of the AnaLASER zone that is
being viewed.
Print the AnaLASER Smoke Level
Press PRINT when the S in SMOKE_LEV
is blinking to print the ANALASER
SMOKE_LEV.

and press ENTER. The System displays
the air flow level for the address specified:
010-004
50%
>>!
* <<
NORM
The bar graph in the example above shows

the following information for the AnaLASER
device at address 010-004:
50% = 50% of full scale air flow level
!
= low air flow trip point at 20%
*
= high air flow trip point at 90%
NORM indicates that the current air flow
level is at a normal level, HIGH indicates
airflow is too high, and LOW indicates
airflow is too low. The bar graph continuously updates to reflect the current state of
the AnaLASER zone that is being viewed.
The System asks you for a module number:


number and press ENTER. The System
sends smoke levels for all devices on the
selected MODULE to the printer.
AnaLASER Smoke Levels at 13:23:31 Jan 03, 20XX
010-001 13:23:31 Jan 03,20XX
0% Scale >> . . .<< NORM, Cust Msg 1
010-002 13:23:32 Jan 03,20XX
100% Scale >>!!!<< ALRM, Cust Msg
010-010 13:23:31 Jan 03,20XX
42% Scale >>! .
.<< PRE1, Cust Msg 10
010-011 13:23:32 Jan 03,20XX
100% Scale >>!!
.<< PRE2, Cust Msg 11
For printed bar graphs, the characters

shown below indicate the following:
. = an inactive trip point
! = an active trip point
List Analaser Flow_Lev
Press ENTER when the F in FLOW_LEV is
blinking to select LIST ANALASER
FLOW_LEV.
device number:
Print the AnaLASER Flow Level

Press PRINT when the F in FLOW_LEV is
blinking to print the ANALASER
FLOW_LEV.

sends air flow levels for all devices on the
selected MODULE to the printer.
AnaLASER Air Flow Levels at 13:23:31 Jan 03, 20XX
010-001 13:23:31 Jan 03,20XX
0% Scale >> .
. << LOW, Cust Msg 1
010-002 13:23:32 Jan 03,20XX
100% Scale >>! !<< HIGH, Cust Msg
010-010 13:23:31 Jan 03,20XX
42% Scale >>!
. << NORM, Cust Msg 10
010-011 13:23:32 Jan 03,20XX
100% Scale >>!
. << NORM, Cust Msg 11
List Analaser Trip_pts

Press ENTER when the T in TRIP_PTS is
blinking to select LIST ANALASER
TRIP_PTS.
3-33
Operation
The System prompts you to select between
ALARM_TRIP and FLOW_TRIP.
Press ENTER when the A in ALARM_TRIP
is blinking to select LIST TRIP_PTS
ALARM_TRIP.
device number.

the current alarm trip point settings for the
address specified:
010-004 P1: 20%
P2: 60%
ALM: 90%
Print the AnaLASER Alarm Trip Pts

Press PRINT when the A in ALARM_TRIP
ALARM_TRIP points.

sends alarm trip point levels for all devices
on the selected MODULE to the printer.
010-004
LOW:
20%
HIGH:
80%
Print the AnaLASER Flow Trip Pts

Press PRINT when the F in FLOW_TRIP
FLOW_TRIP points.

number and press ENTER.
The System sends air flow trip point levels
for all devices on the selected MODULE to
the printer.
AnaLASER Air Flow Trip Points at 13:23:31 Jan 03, 20XX
010-001 13:23:31 Jan 03,20XX, LOW: 10% HIGH: 90%,
Cust Msg 1
010-002 13:23:31 Jan 03,20XX, LOW: 20% HIGH: 80%,
Cust Msg 1
010-010 13:23:31 Jan 03,20XX, LOW: 30% HIGH: 70%,
Cust Msg 1
010-011 13:23:31 Jan 03,20XX, LOW: 10% HIGH: 80%,
Cust Msg 1
List: Percent/ft
AnaLASER Alarm Trip Points at 13:23:31 Jan 03, 20XX

010-001 13:23:31 Jan 03,20XX, PRE1: 10% PRE2: 30%
ALRM: 100%, Cust Msg 1
010-002 13:23:31 Jan 03,20XX, PRE1: 30% PRE2: 50%
010-010 13:23:31 Jan 03,20XX, PRE1: 10% PRE2: 50%
010-011 13:23:31 Jan 03,20XX, PRE1: 50% PRE2: 80%
Use List Percent/ft to show settings in

percent/ft obscuration of the ILI and ILP
Series detectors.
Press ENTER when the F in FLOW_TRIP is

blinking to select LIST TRIP_PTS
FLOW_TRIP.
Press ENTER to select List Percent/ft. The

number.

device number.

number and three-digit ACC device ad-
3-34
dress number using the numeric keypad

the current air flow trip point settings for the
address specified:

arrow key to cause the P in PERCENT/FT
to start blinking:
LIST: PERCENT/FT
Type in the three-digit module number and

the three-digit device number using the
numeric keypad and press ENTER. The
System displays the following menu for that
device (the S in Senstvty will be blinking):
Operation
002-003 SENSTVTY
PRE-ALARM
ANALOG
List Percent/ft Senstvty

The display for Sensitivity supplies the
current sensitivity as read back from the
detector and is similar to the following
(readings are dynamic):
002-003 SENS 1.4%/FT
NORM
List Percent/ft Pre-alarm

The display for Pre-alarm supplies the
current Pre-alarm setting read back from
the detector and is similar to the following
002-003 PRE-ALARM 1.4%/FT
NORM
The System prints either the Sensitivity, Prealarm, or Analog of all the devices for the
specified module in a format similar to the
following (NA = ID-60 detector):
%/ft SENSITIVITIES FOR MODULE 2
1-3.00 2-NA
3-1.4 4-3.1 5-1.4
6-1.4 7-ND
8-ND
9-ND
10-ND
11-ND 12-ND 13-ND 14-ND 15-ND
16-ND 17-ND 18-ND 19-ND 20-ND
21-ND 22-ND 23-ND 24-ND 25-ND
26-ND 27-ND 28-ND 29-ND 30-ND
31-ND 32-ND 33-ND 34-ND 35-ND
36-ND 37-ND 38-ND 39-ND 40-ND
41-ND 42-ND 43-ND 44-ND 45-ND
46-ND 47-ND 48-ND 49-ND 50-ND
51-ND 52-ND 53-ND 54-ND 55-ND
56-ND 57-ND 58-ND 59-ND 60-ND
List: ASD_apps
Use List ASD_apps to display operational
characteristics of the ASD devices.
List Percent/ft Analog

The display for Analog supplies the current
analog2 reading read from the detector and
is similar to the following (readings are
dynamic):
002-003 SENS 1.4%/FT
NORM
To leave the Percent/ft menu without going

through all subaddresses, press the Up
arrow key. The System displays the List
menu.
Print the Analog Loops Current Readings in
Percent/ft Obscuration
Press PRINT when the P in Percent/ft is
number.

arrow key to cause the A in ASD_Apps to
start blinking:
LIST: ASD APPS
Display the Operational Characteristics of One

Device
Press ENTER to select ASD_apps. The
number:

leading zeros.)
The System displays the currently assigned

application for the device specified. (Refer to
the ASD Submenu Abbreviations on page I-1.)

the numeric keypad and press ENTER. The
System shows the following menu for that
device (the S in Senstvty will be blinking):

assigned application of each succeeding
device. The System will exit the ASD_Apps
menu if there are no more ASD devices in
that module.
001-001 SENSTVTY
PRE-ALARM
ANALOG
To leave the List ASD_Apps menu at any

time, press the Up arrow key. The System
displays the List menu.
3-35
Operation
To print the operational characteristics of the ASD
devices assigned to an ALD Loop
Press PRINT when the A in ASD_Apps is
number:
Arm/Disarm (Arm/dis)
Arm
Disarm
Output_on/off
Arm
Disarm
(Enter all leading zeros.) The System prints
a list of all the applications currently assigned to all the ASD devices in that ALD
loop in a format similar to the following (ND
= No Device):
1-NONE
6-ND
11-ND
16-ND
21-ND
26-ND
31-ND
36-ND
41-ND
46-ND
51-ND
56-ND
2-PARK
7-ND
12-ND
17-ND
22-ND
27-ND
32-ND
37-ND
42-ND
47-ND
52-ND
57-ND
3-ND
8-ND
13-ND
18-ND
23-ND
28-ND
33-ND
38-ND
43-ND
48-ND
53-ND
58-ND
4-ND
9-ND
14-ND
19-ND
24-ND
29-ND
34-ND
39-ND
44-ND
49-ND
54-ND
59-ND
5-ND
10-ND
15-ND
20-ND
25-ND
30-ND
35-ND
40-ND
45-ND
50-ND
55-ND
60-ND
Energize
De_energize
Loop arm/disarm
arm
disarm
Net_link_request
Analazer
Alarm-trip
Flow-trip
Percent/ft
Sensitivity(Senstvty)
Pre-alarm
Change-apps
Use the Control menu to perform the
following functions:
Reset the System
Change the sensitivity of a smoke
detector
CONTROL Menu
The Control menu has nine items from

which to choose; six of the items have
submenus, as follows (the shortened terms
used in the menu are in parentheses):
Arm an output device

Disarm and energize an output device
Disarm and de-energize an output
device
Reset
Arm and disarm a loop
Send a request to the Network

Command Center (NCC) to disconnect
the MXL from the network
Hi_3
Hi_2
Hi_1
Norm
Low_1
Low_2
Low_3
3-36
Arm or disarm an initiating device
Change AnaLASER Alarm Trip points

and Flow Trip points
Change sensitivity and pre-alarm
settings in percent/ft obscuration of the
ILI and ILP detectors
Change the application of an ASD device
Operation
Entering the Control Menu

From the Main Menu, use the arrow keys to
cause the C in CONTROL to blink.
explains the Control function:
TO MODIFY DATA FOR OPERATION

Menu.)
If the System is normal, when SYSTEM

RESET is selected, the System displays
the following:
SYSTEM ALREADY NORMAL

menu each time.)
Press ENTER to select CONTROL.

The System asks you for a password
before it allows you to use the Control
functions. Enter your one- to five-digit
password, using the numeric keypad, and
press ENTER (See the discussion under
Entering Your Password on page 3-17).
displays the first Control menu, with the R in
RESET blinking:
Control: Sensitivity
Use Control Sensitivity to change the
sensitivity settings of smoke detectors on
analog loops.
From the Control menu, press the Right or
Left arrow key to cause the S in SENSTVTY
to start blinking:
CONTROL: RESET SENSTVTY ARM/DIS

displays:
menu each time.)
CHANGE SENSITIVITY
Control: Reset
Note that Control Sensitivity allows you to

change the sensitivity settings of smoke
detectors only; if you attempt to change the
sensitivity setting of another type of device,
the System displays:
Use Control Reset to initiate a system reset

at any time.
From the Control menu, use the Left or
Right arrow key to cause the R in RESET to
start blinking:
Press HELP again to return to the above

menu.)
[001-001] NOT SMOKE DETECTOR
If you enter any address for which there is

no device assigned, the System displays:
(If you press HELP while the R in RESET is
blinking, the System explains this function:
NO DEVICE ASSIGNED
RESET SYSTEM
Press ENTER while the S in SENSTVTY is

blinking to select CONTROL SENSTVTY.
menu.)
Press ENTER to reset the System and
display the following message:
The System asks you for a module number

and device number:
SYSTEM RESET
3-37
Operation
System shows the following display:
001-001 Norm Hi 1 Hi 2 Hi 3
The current sensitivity setting is highlighted.

The System offers you a choice of seven
levels of sensitivity: Hi_3, Hi_2, Hi_1, Norm,
Low_1, Low_2 or Low_3. Use the Right and
Left arrow keys to highlight the level you
wish to set for the smoke detector specified
and press ENTER. The System makes the
change in sensitivity setting.
001-001 ARM DISARM
Press NEXT to move through the devices

until you display the ones you want to
change, and follow the instructions above for
making the changes.
When you disarm an input device, the

System automatically annunciates the
disarming as a Trouble and lights the
PARTIAL SYSTEM DISABLE LED.
When the System has displayed the

highest numbered device for the module
specified, it returns to the Control menu.
You can select another address by selecting SENSTVTY and following the instructions above.
Press NEXT to move through the devices

change; follow the instructions above for
making the changes.
The System offers you a choice of arming

or disarming the device. Use the Right and
Left arrow keys to highlight your choice and
press ENTER. The System makes the
change.
To leave the Control Sensitivity displays

without going through the entire list, press
the Up arrow key. The System displays the
Control menu.

specified, it returns to the Control menu. To
arm or disarm another module device,
select ARM/DIS and follow the preceding
instructions.

menu each time.)

menu each time.)
Control: Arm/dis
Control: Output on/off
Use Control Arm/dis to enable or disable

the operation of an initiating device.
Use Control Output_On/Off to arm or

disarm an output device. In addition, you can
energize or de-energize disarmed output
devices.
From the Control menu, press the Left or

Right arrow key to cause the A in ARM/DIS
to start blinking.
displays:
DISARM OR ARM DEVICES
Press HELP again to return to the Control

menu.)
Press ENTER while the A in ARM/DIS is
blinking to select Control Arm/dis.
3-38
The System asks you for the module

number and device number of the detector
you wish to arm or disarm. Type the threedigit module number and three-digit device
number using the numeric keypad and
The System displays:

Right arrow key to cause the O in OUTPUT
to start blinking:
CONTROL ARM/DIS OUTPUT_ON/OFF

displays:
TURN OUTPUTS ON OR OFF
Operation
menu.)
Press ENTER while the O in OUTPUT is
blinking to select CONTROL_OUTPUT ON/
OFF.
The System asks for a module number and
device number of the device you wish to turn
on or off (energize or de-energize). Type
the three-digit module number and threedigit device number using the numeric
keypad and press ENTER. (Enter all
leading zeros.)

menu each time.)
Control: Loop Arm

Use Control Loop Arm to enable the operation of a loop of ALD initiating devices.
Right arrow key to cause the L in
LOOP_ARM to start blinking.
The System shows the following display:

displays:
253-005 ARM DISARM
TO ARM ALL INPUTS ON A LOOP
The System offers you a choice of arming

or disarming the device.

menu.)
Use the Right and Left arrow keys to

highlight your choice and press ENTER.
Press ENTER while the L in LOOP_ARM is

blinking to select Control Loop_arm.
If you have armed the device, you can

press NEXT to display the number of the
next device in the sequence. You can also
press the Up arrow key to return to the
Control menu.

number of the ALD loop you wish to arm.
(Enter all leading zeros.)
NOTE: You must first disarm a device if

you wish to energize or de-energize it.
When you arm input devices, the System

automatically annunciates the arming as a
Trouble OUT, and lights the PARTIAL
SYSTEM DISABLE LED.
When you disarm an output device, the

disarming as a Trouble and a Partial
System Disable.
If you choose to disarm an output device,
the System then asks if you wish to energize
it or de-energize it:
253-005 ENERGIZE DE ENERGIZE
Use the Right or Left arrow key to energize

or de-energize the device and press ENTER.
Press NEXT to move through the outputs
change; follow the instructions above for
making the change.
specified, it returns to the Control menu. To
arm or disarm and energize or de-energize
a device on a different module, follow the

menu each time.)
Control: Loop Disarm

Use Control Loop Disarm to disable the
operation of a loop of ALD initiating devices.
Right arrow key to cause the L in
LOOP_DISARM to start blinking.
displays:
TO DISARM ALL INPUTS ON A LOOP

menu.)
3-39
Operation
Press ENTER while the L in LOOP_DISARM
is blinking to select Control Loop_disarm.
Press ENTER when the A in ANALASER is

blinking to select Control ANALASER.

number of the ALD loop you wish to disarm.
(Enter all leading zeros.)
The System prompts you to select between ALARM_TRIP and FLOW_TRIP.
When you disarm input devices, the

disarming as a Trouble IN, and lights the
PARTIAL SYSTEM DISABLE LED.
menu each time.)
Control: Net Link Request

Use Control Net_Link_Request to connect
or disconnect that particular panel from the
X-Network. When the panel is disconnected from the X-Network, the panel
maintains its functions, but it does not
exchange messages with other nodes in the
X-Network.
Right arrow key to cause the N in
NET_LINK_REQUEST to start blinking.
displays:
REQUEST NCC DISCONNECT/RECON NODE

menu.)
Press ENTER when the A in ALARM_TRIP

is blinking to select CONTROL ALARM_TRIP.
device number.

current alarm trip point settings for the
address specified:
010-004 P1: 20%
P2: 60%
ALM: 90%
Use the numeric keypad and the left and

right arrow keys to modify the value for P1,
P2, and ALM (Alarm). Note that the following provisions apply:
P1 must be less than or equal to P2
which must be less than or equal to
ALM. If these values are different, the
System will reject the settings.
P1, P2, and ALM must be even multiples
of 10% or the System will reject the
settings.
Press ENTER when you are finished
modifying the settings. The display should
then show:
Press ENTER while the N in

NET_LINK_REQUEST is blinking to
disconnect the panel from the X-Network.
TRIP POINTS ACCEPTED
To reconnect the panel to the X-Network,

from the Control menu, press the Left or
Right arrow key to cause the N in
NET_LINK_REQUEST to start blinking and
press ENTER.
TRIP POINTS INVALID.
or
Press ENTER when the F in FLOW_TRIP

is blinking to select Control FLOW_TRIP.
device number.
Control: Analaser
Use Control ANALASER to display and
change the operational characteristics of
the AnaLASER devices.
3-40

Operation
current air flow trip point settings for the
address specified:
010-004
LOW: 20%
HIGH: 60%
Use the numeric keypad and the left and

right arrow keys to modify the value for
LOW and HIGH. Note that the following
provisions apply:
Use the left and right arrow keys on the

keypad to lower or raise the %/ft reading.
(Refer to the Sensitivity and Pre-Alarm
Settings chart that follows.)
PHOTO
ION
Pre-alarm adjust
increment
.25% / ft.
.12% / ft.
LOW must be less than HIGH, or the

System will reject the settings.
Pre-alarm range
.25 - 2.0% / ft.
.25 - .75% / ft.
The System will reject the settings if they

are not even multiples of 10%.
Pre-alarm default
1.5% / ft.
.75% / ft.
Sensitivity adjust
increment
~.25% / ft.
~.12% / ft.
Sensitivity range
1.25 - 3.4% / ft.
.6 - 1.6% / ft.
Sensitivity default
(Norm)
3.0% / ft.
1.4% / ft.
Press ENTER when you are finished

modifying the settings. The display should
then show TRIP POINTS ACCEPTED.
Control: Percent/ft
Use Control Percent/ft to change sensitivity
and pre-alarm settings in percent/ft obscuration of the ILI and ILP series of detectors.
Right arrow key to cause the P in Percent/ft
to start blinking. The System asks you for a
module number and device number.

System displays the following:
001-001 SENSTVTY
PRE-ALARM
Control Percent/ft - Senstvty

The display for Sensitivity supplies the
current sensitivity as read back from the
detector and is similar to the following
002-003 SENS 1.4%/FT
NORM
In the previous message, 002-003 is the

address. Sens is the type of response
(Sensitivity or Pre-alarm). 1.4%/ft is the
smoke detector reading in %/ft obscuration
and Norm is the text sensitivity range
corresponding to the %/ft readings.
After you change the sensitivity setting, the

System prints the information for the
selected device in a format similar to the
following:
CMD CHANGE SENS
06:38:20 JUN 2, 20XX
002-004 1.4%/FT NORM
Control Percent/ft - Pre-alarm

The display for Pre-alarm supplies the
current pre-alarm setting read back from
the detector and is similar to the following
002-003 PRE-ALARM .75%/FT
NORM
In the previous message, 002-003 is the

address. Pre-alarm is the type of response
(Sensitivity or Pre-alarm). .75%/ft is the
smoke detector reading in %/ft obscuration
and Norm is the text sensitivity range
corresponding to the %/ft readings.
Use the left and right arrow keys on the
keypad to lower or raise the %/ft reading.
(Refer to the Sensitivity and Pre-Alarm
Settings chart.)
3-41
Operation
After you change the pre-alarm setting, the
System prints the information for the
selected device in a format similar to the
following:
CMD CHANGE PRE-ALM 06:38:20 JUN 2, 20XX
002-004 1.4%/FT NORM
NOTE: Because the pre-alarm and sensitivity settings overlap, set the pre-alarm to
at least an increment below the sensitivity
setting.
Control: Change Apps

Use Control Change_Apps to change the
application of an ASD device.
Right arrow key to cause the C in
Change_Apps to start blinking.
displays:
CHANGE DEVICE'S APPLICATIONS

menu.)
Press ENTER while the C in Change_Apps
is blinking to select Control Change_Apps.
The System asks you for the module and
device number.
Control: Change_Apps Reset >
Type in Module & Device: 001-001

[Enter
module-device number, including all leading zeros]
001-001 NONE OFFC WHSE LOBY > [Use arrow
keys to select the desired application]
001-001 NONE OFFC WHSE LOBY >
COMMAND +HANGE_APPS 09:41:43 AUG 07,

20XX 001-001 NONE > OFFC
To leave the Change_Apps menu at any

time, press the Up arrow key.
NOTE: If the ASD application is changed
while Test ASD is on, the changes will not
be effective until Test ASD is turned off.
TEST Menu
The Test menu has sixteen items from

which to choose; three of those items have
submenus, as follows (the shortened terms
used in the menu itself are in parentheses):
Set_time
Ground fault (GND_FLT)
Power*
Main
Voltage
Current
LEDs
Display
Device_LED
MOI_Lamp_test
Use the arrow keys to cycle through the 11

supported applications described in the
ASD Submenu Abbreviations on page I-1,
in Appendix I, and press ENTER to select
the desired application.
X_Network*
The transaction and the time that it occurs

will be printed on the printer as a confirmation. The example shown below assumes
that no application is currently assigned to
module 001, device 001:
Event_log
M_Network*
Override
Det_cleaned
Alrm_only
Trbl_only
Superv_only
Security_only
3-42
[Press ENTER]
A statement will be printed out to confirm

the change:
Lamp_test
leading zeros.)
[Press ENTER]
Operation
All_events
Hist_Ctrl
Hist_Erase
PYRO_Diags
PRE_ALARM
ASD_DEVICES
SUMMARIZE
MANUAL_ACTIVATE
*You can print a report of the information
produced by these functions. See the
discussions for Test Power and Test Network.
Press ENTER to select TEST. The System

asks you for a password before it allows
you to use the Test functions. Enter your
one- to five-digit password, using the
numeric keypad, and press ENTER (See
the discussion under Entering Your
Password on page 3-17).
displays the first Test menu.
menu each time.)
Use the Test menu for the following functions:

Change the time and date in the System
Test: Set Time
Test ground fault state
Use Test Set_Time to set the time and date

for the System.
Display the Systems power condition

Test the LEDs or the display on the
MKB-4
Test the LEDs on an analog device
Perform lamp test on MOD-16 of MOI-7
Display network performance
characteristics
From the Test menu, use the Left or Right

arrow key to cause the S in SET_TIME to
start blinking:
TEST: DETECTOR NETWORK SET-TIME
Alarm verification/confirmation override

displays:
IEC detector cleaned function
SET SYSTEM TIME
Event (History) log menu

Test Pre-alarm logic
Test ASD detectors

menu.)
Record one summarized trouble for an

entire module
Press ENTER when the S in SET_ TIME is

blinking to select TEST SET_ TIME.
Perform testing on input points and

simutale alarms
The System shows you the current System

time, using a 24-hour clock, and the date:
SET TIME = 12:34:56 12/23/20XX
Entering the Test Menu

From the Main Menu, use the Left or Right
arrow keys to cause the T in TEST to begin
blinking.
explains the Test function:
TO TEST SYSTEM, LOOP & DEVICE

Menu.)

displays:
TYPE HH:MM:SS MM/DD/YYYY <ENTER>
The Help display tells you to type the time

and date, using the numeric keypad, in the
following format: hour: minute:
seconds_month/day/year, and then to
press ENTER to set the time and date. Use
the Right and Left arrow keys to skip over a
correct digit.
3-43
Operation
menu.)
Type the time and date as explained above
and press ENTER. The System prints the
current time and date on the printer and
returns you to the Test menu.
menu each time.)
Test: Power
Use Test Power to test the Systems
battery voltage, AC voltage, and battery
charge current.
arrow key to cause the P in POWER to
start blinking:
TEST: GND-FLT POWER

displays:
Test: Ground Fault

Use Test Gnd_flt to test the present condition of the ground fault detection circuitry.
arrow key to cause the G in GND_FLT to
start blinking:
TEST: NETWORK SET TIME GND FLT
DISPLAY POWER

menu.)
Press ENTER when the P is blinking and
the menu displays:
POWER: MAIN

displays:
GROUND FAULT TEST
Press HELP again to return to the Test

menu.)
Press ENTER when the G is blinking and
the menu displays:
GND FLT: MAIN
From the Ground Fault menu, press ENTER

when the M in MAIN is blinking.
The System tests dynamically for ground
fault and reports the results of the test on
the display (OK, PLUS, or MINUS):
GROUND FAULT IS MINUS
If the message is other than OK, locate the

loop and the device responsible. The
display automatically changes to OK when
the ground fault problem is corrected.
(During this test, the System and its
devices remain operational.)
3-44

menu each time.)
Display the AC Voltage, Battery Voltage, and

Charging Current of the Main System
From the Power menu, press ENTER when
the M in MAIN is blinking to select Main
Power.
The System shows the following menu:
MAIN: VOLTAGE CURRENT
Press ENTER when the V in VOLTAGE is

blinking to display the battery voltage:
BATTERY VOLTAGE = X.X VOLTS
Press ENTER again to display the AC

voltage:
AC VOLTAGE = X VOLTS
Press the Up arrow key to return to the

Main Power menu. Use the Right arrow key
to cause the C in CURRENT to start
blinking and press ENTER. The System
shows the battery charge current in amps:
BATT CHG CUR = XX.X AMPS
Press the Up arrow key twice to return to

the Power menu.
Operation
Print the AC Voltage, Battery Voltage, and
Charging Current of the Main System
From the Power menu, press PRINT when
the M in MAIN is blinking to select MAIN
POWER. The System will print information
in a format similar to the following:
Power Supply Statistics at 11:23:52
May 01, 20XX:
Battery Voltage = 26.0 volts Charging
CUR = 0.5 AMPS
AC VOLTAGE = 113 VOLTS
Test: Device LED

Use Test Device_LED to test the LEDs on
the Systems analog devices.
arrow key to cause the D in DEVICE to
start blinking:
TEST: LAMP TEST DEVICE LED

displays:
TURN ON DEVICE LEDs
Test: Lamp Test

Use Test Lamp_test to test the LEDs on
the alphanumeric display on the MKB-4.
arrow key to cause the L in LAMP to start
blinking:
TEST: GND-FLT POWER LAMP TEST

explains this function:
MKB-4 LAMP TEST

menu.)
Press ENTER when the L is blinking to
select TEST LAMP_TEST. The System
displays the following menu:
LAMP TEST: LED'S DISPLAY
Press ENTER to test the LEDs and the

audible on the MKB-4. The LEDs light for 5
seconds and then return to their previous
state.
To test the alphanumeric display, press the
Right arrow key once to cause the D in
DISPLAY to start blinking and then press
ENTER. The System tests the display and
then returns to the Lamp Test menu.
menu each time.)

menu.)
select TEST DEVICE_LED.
The System asks you to type the module
and device numbers. Type the three-digit
module number and the three-digit device
number and press ENTER. (Enter all
leading zeros.)
The System displays the following menu for
the device (the O in ON will be blinking):
001-001 ON OFF
To turn on the LED for that device, press

ENTER. The System turns on the LED for that
device. Turning on a device LED automatically
causes a Trouble to be annunciated.
Use the NEXT key to move through the
devices until you display the ones whose
LEDs you wish to test. Follow the instructions above.
specified, it returns to the Test menu.
To turn on a device LED for a different
module, select DEVICE_ LED from the
Test menu and follow the preceding
instructions.
Main Menu, or to leave the menu at any
3-45
Operation
Test: MOI Lamp Test

Use MOI_lamp_test to test the MOD-16
outputs of an MOI-7.
arrow key to cause the M in MOI to start
blinking:
TEST: DEVICE LED MOI Lamp Test

menu.)
Press ENTER when the O in OVERRIDE is
blinking and the menu displays:
OVERRIDE: ALR VERIFY ALR CONFIRM
Use the Left or Right arrow key to switch

between ALR_VERIFY and ALR_CONFIRM.
displays:
TO TEST MOI-7 / MOD-16 LAMPS

menu.)
Press ENTER when the M is blinking to
select MOI_LAMP_TEST.
number. Type the three-digit module
leading zeros.)
If the MOI-7 module is present in CSG-M
the MOD-16 outputs will be placed in a 30second lamp test mode. After 30 seconds,
these outputs return to their previous state.
Main Menu, or to leave the menu at any
Test: Network
(X-Network, M-Network)
This function is used only by Siemens
Building Technologies, Inc. engineers to
observe network traffic so that they can
evaluate the operation of the module
communication network.
Test: Override

OVERRIDE: YES NO
A blinking Y in YES indicates that Alarm

Verification Override is currently enabled. A
blinking N in NO indicates that the Alarm
Verification Override is currently disabled.
To enable Alarm Verification Override, use
the Left or Right arrow key to cause the Y
in YES to start blinking. Pressing ENTER
when the Y in YES is blinking will cause
Alarm Verification Override to be enabled.
The System will display the following
message:
OVERRIDE ENABLED
To disable Alarm Verification Override, use

the Left or Right arrow key to cause the N
in NO to start blinking. Pressing ENTER
when the N in NO is blinking will cause
Alarm Verification Override to be disabled.
The System will display the following
message:
Use Test Override to override the CSG-M

selected options for Alarm Verification and
Alarm Confirmation.
OVERRIDE DISABLED

arrow key to cause the O in OVERRIDE to
start blinking.
In either case, if the Alarm Verification

option was not selected in CSG-M, the
System will display the following message:

displays:
FEATURE NOT ENABLED IN CSG
OVERRIDE ALARM VERIFY & CONFIRM
3-46
Override the Alarm Verification CSG-M

Selection
From the Override menu, press ENTER
when the A in ALR_VERIFY is blinking to
select Alarm Verification.
Operation
Override the Alarm Confirmation CSG-M
Selection
From the Override menu, press ENTER
when the A in ALR_CONFIRM is blinking to
select Alarm Confirmation.

displays:

menu.)
OVERRIDE: YES NO
TO INDICATE DETECTOR CLEANED

select DET_CLEANED.
A blinking Y in YES indicates that Alarm
Confirmation Override is enabled. A blinking
N in NO indicates that the Alarm Confirmation Override is disabled.
To enable Alarm Confirmation Override, use
the Left or Right arrow key to cause the Y
in YES to start blinking. Pressing ENTER
when the Y in YES is blinking enables Alarm
Confirmation Override. The System will
OVERRIDE ENABLED
To disable Alarm Confirmation Override, use

the Left or Right arrow key to cause the N
in NO to start blinking. Pressing ENTER
when the N in NO is blinking disables Alarm
Confirmation Override. The System will
OVERRIDE DISABLED
In either case, if the Alarm Confirmation

option was not selected in CSG-M, the
System will display the following message:
FEATURE NOT ENABLED IN CSG

and device numbers. Type the three-digit
module number and the three-digit device
leading zeros.)
After entering the module-device, the
MXL-IQ determines if the device is subject
to IEC. If the device is not subject to IEC or
if IEC is not enabled for the system, error
messages display (Device not subject to
IEC; IEC not enabled in CSGM).
If the device is an IEC detector, the MXL-IQ
will display and print the time, date, moduledevice and custom message of the cleaned
device.
Test: Event Log

See Section 6, MXL-IQ History Log.
Test: Pyro_diags
Use Test Pyro-diags to display a series of
statistics typically used by Siemens Building
Technologies, Inc. to evaluate the operation
of the System. A special password is
required for access to this function.
Test: Pre_alarm
Test: Det_Cleaned
Use Test Det_cleaned to indicate that a
selected detector has been cleaned. This
option is only operational if IEC is enabled in
the CSG-M (See Appendix F).
arrow key to cause the D in DET_CLEANED
to start blinking:
TEST: OVERRIDE DET CLEANED
Use Test Pre_alarm to test pre-alarm logic.

From the Test menu, use the left or right
arrow key to cause the P in Pre_alarm to
start blinking:
TEST: PRE ALARM

and device number.
3-47
Operation
the three-digit device number using the
numeric keypad and press ENTER.
The System then sends information to force
this detector into pre-alarm. Once it prealarms, or after a delay, the MXL-IQ then
restores the detector to its proper pre-alarm
setting.
Test: ASD_Devices
Use Test ASD_Devices to disable ASD
parameters and allow timely response to
test gas.
arrow key to cause the A in ASD_Devices
to start blinking.
(If you press HELP at this point, the system
displays:
TEST: ASD DETECTORS
Press HELP again to return to the Test

menu.)
Press ENTER to test the ASD devices
present in the system. The System displays:
TESTING OF ASD DEVICE ENABLED
Press the ENTER key again and the

System displays:
TROUBLE OUT 253 08:25:50 AUG 08, 20XX

#9 CERBERUS PYROTRONICS ,
ASD TESTING DISABLED, MXL PANEL
If Test ASD_Devices is activated and left

alone, the system will automatically disable
the test (time out) after four hours.
Test ASD_Devices is inhibited while the

system is initializing or resetting.
Test: Summarize
Use Test Summarize to ignore known
troubles, and instead view one summarized
trouble for an entire module. This is typically
used during installation and commissioning.
Select Summarize and press ENTER. The
System displays the following menu:
Select Mods
ON
OFF
Test: Summarize - Select_Mods

Use Test Summarize Select_Mods to scroll
through all installed (CSG-M) module
addresses and enable/disable the summarize feature for each module address.
Choose Select_Mods and press ENTER.
The System displays the following:
001
YES
NO
Press NEXT and the System displays:
TESTING OF ASD DEVICE DISABLED
002
Press the ENTER key to toggle between

Testing Enabled (Trouble In) and Testing
Disabled (Trouble Out). When toggling
between Testing Enabled and Testing
Disabled, there is a three minute time
period that separates the two states.
The System flashes the currently active

summarize selection for the module
address. The operator may then press the
right or left arrow keys to highlight either
YES or NO and then press the ENTER key
to accept and program the selection. When
ENTER is pressed, the System scrolls to
the next installed module address. The Up
arrow key terminates the Select_Mods
mode.
Activating the ASD_Devices command will

post a Trouble into the system which will be
printed out as:
TROUBLE IN 253 08:24:53 AUG 08, 20XX
#8 CERBERUS PYROTRONICS ,
ASD TESTING ENABLED, MXL PANEL
3-48
Pressing ENTER a second time will cause

the following message to be printed out:
YES
NO
All Select_Mods selections remain intact

until the System is turned off, even if
summarize mode is toggled.
Operation
One trouble is posted per module
address, regardless of how many
troubles are detected at that module
address.
and turns on the Partial System Disable

LED. The System displays one summarized
trouble for the total system.
A trouble is not posted unless at least

one trouble is detected at that module
address.
Test: Manual_Activate
The trouble report is consistent with

existing MXL-IQ trouble messages and
the text reads Troubles summarized.
The MXL-IQ only reports TRBL-INs
when summary mode is enabled at an
address.
Alarm, supervisory, security, and status
event reporting are not effected.
Modules which are NOT selected for
summary report their troubles as usual,
even if summary mode is turned on for
other module addresses.
When a module address is summarized,
individually occurring troubles are not
broadcast to XNET; the single Troubles
summarized trouble is broadcast to XNET.
The Troubles summarized trouble is
implemented as any other system trouble,
being logged to history, taking up one of the
300 trouble slots, and appearing in List
Troubles requests. All summarize selections are unaffected through RESET and
default to CSG-M setting at power up.
Test: Summarize - OFF
When Summarize OFF is selected, the
System annunciates the following trouble:
System Commissioning Mode TRBL OUT
and turns off the Partial System Disable

LED. Preexisting Troubles summarized
events remain and the System reverts to
normal trouble reporting and processing for
all new troubles.
Test: Summarize - ON
When Summarize ON is selected, the
System annunciates the following trouble:
System Commissioning Mode TRBL IN
Use Test Manual_Activate to:

Perform testing on input points and the
associated output logic expected when
the point is activated.
Generate alarms and associated output
activations.
Select Manual_Activate and press ENTER.
and device number.
Type In Module & Device:

three-digit device number using the numeric keypad and press ENTER. Upon
entering the device address, the System
performs as follows based on the point
type:
MANUAL INPUT POINT ACTIVATION
No Input Point Error message.
Analog Smoke System issues command to place
device into the alarm state via
Detectors
sensitivity adjustment. Device then
reports alarm as if an actual alarm
occurred. Associated outputs follow.
All Other
Inputs
System will not issue any command

to device, but will synthesize the
reporting of alarm in by the device.
Associated outputs follow.
Test: Manual_Activate - Test

This provides a remote switch that upon
activation/deactivation of the TRI, the
MXL-IQ reads the module-device address
provided and performs the operations
outlined above. This use is primarily for, but
not limited to, testing intelligent duct
detectors.
3-49
Operation
3-50
+D=FJAH
Testing and Troubleshooting

SYSTEM TEST
Important:
If the System is connected to the Fire
Department, or activates an external
System (for example, a leased line
connection), disarm the related
outputs before servicing to prevent
activation. Notify persons in the
facility that you are conducting a
System test so that they can ignore
any alarms that sound during testing.
Be sure to reset the System at the
end of the inspection.
To ensure maximum safety, follow the

procedure described below. To ensure
proper and reliable operation, we recommend the following inspection and testing
schedule:
Every Six Months

1. Check the sensitivity of each detector,
using the List Sensitivity menu (See
page 3-26). Refer to Appendix B for a
list of acceptable detector sensitivity
ranges.
2. If the PARTIAL SYSTEM DISABLE
LED is lit, check that all appropriate
detectors are armed, using the Control
Arm/dis menu (See page 3-38).
3. Activate a detector or alarm-initiating
device. To test for GoNo Go operation,
use CERBERUS PYROTRONICSTM

Test Gas P/N 315-282747, following the
instructions on the label. Check that the
detector LED lights and that the proper
indication is given at the Control Panel.
4. Verify that an alarm can be acknowledged
and that the System can be silenced and
reset (See Acknowledge Alarms on
page 3-18).
5. Verify the time and date setting of the
System clock (See Test Set_Time on
page 3-43).
Every Year
1. Check that the System operates as
programmed by CSG-M and in
accordance with specifications.
2. Perform any other applicable tests
required by national or local fire codes.
Fuse Replacement
Fuse ratings are as follows:
Fuse
F1
F2
F3
F4
For
Main Power
Battery
CZM-1B6 Power
24V Output
Rating
8A, 3 AG, Normal Blow
15A, 3AG, Normal Blow
The fuses are located on the upper portion

of the SMB-2 (See Figure 2, page 1-4).
4-1
TROUBLESHOOTING
Troubleshooting both the external wiring and
the MXL-IQ System wiring follows the steps
in System Function Checkout on page
2-16. If a fault occurs, refer to the Troubleshooting Guide. Locate the type of fault or
any trouble message displayed and follow
the directions in the Corrective Action
column.
Sometimes you can locate a fault quickly

using the Troubleshooting Guide. When
this is not possible, continue with the
checkout procedure on page 2-16 and then
the Troubleshooting Guide until all faults
and troubles are corrected. Then repeat the
checkout procedure to ensure that no
additional problems were introduced and
that the original problem was corrected.
TABLE 19
TROUBLESHOOTING GUIDE
This guide assumes that all modules, devices, and wiring are installed.
Note:
Do NOT change modules or wiring unless power is OFF. If available, use your printer during
troubleshooting operations.
SYMPTOM
1. POWER LED is not lit;
display on MKB-4 is
blank.
PROBABLE CAUSE
CORRECTIVE ACTION
No AC Battery
Check AC and battery. Check fuses F1 and F2 on the SMB-2 and the circuitbreaker
on the MPS-6. Check AC and battery wiring.
If power connections are OK, check the cable between the SMB-2 and MKB-4 for
proper installation.
2. POWER LED is on,

MKB-4 display is blank.
Problem on the MKB-4.
Adjust contrast control R14 on the ANN-1 board. Remove the MKB-4 and check
cable from ANN-1 to the display. If MKB-4 is defective, replace it.
3. MKB-4 display shows

the following default
message:
CERBERUS
PYROTRONICS MXL
Improper address on MKB-4
Correct address setting on the MKB-4 using S1. See the installation instructions for
the MKB-4, page 2-4.
No communication between
SMB-2 and MKB-4.
Defective MKB-4.
Check the cable between the SMB-2 and the MKB-4. Replace the cable if defective.
Replace the MKB-4.
If MOM-2/4 installed, defective

network modules(s).
Defective SMB-2
Disconnect the MOM-2/4 from the SMB-2. If probelm resolved, reconnect

MOM-2/4 and remove all modules from MOM-2/4. Reinstall all modules one
at a time. Replace any that cause the problems to reoccur.
Replace SMB-2
4. Device troubles on
analog loops.
Errors in loop wiring and

installation of devices.
Check loop wiring for shorts, opens, etc. using the Field Wiring Checkout Guide
(page 2-11).
Check that all analog devices are I or IL Series devices, or are CZM-1B6s. See the
list of compatible devices in the appendixes.
Check that all devices are installed.
Check that all devices installed comply with the configuration printout from CSG-M.
Check printed trouble list for ID troubles and correct device IDs as required. Check
devices using the FPI-32 Programmer Tester. Replace devices that fail to respond.
4-2

TABLE 19
TROUBLESHOOTING GUIDE (Continued)
SYMPTOM
5. Trouble with notification
appliance circuits
(NACs).
PROBABLE CAUSE
CORRECTIVE ACTION
End-of-line resistor improperly

or not installed.
Check that the end-of-line resistor is 2.2K, W and is installed according to the
instructions.
Notification appliances
improperly installed.
Check notification appliances for presence of polarizing diodes and correct device
wiring.
Check NACs for proper wiring (shorts, opens, etc.). Use the Field Wiring Checkout
Guide, page 2-11.
6. Output devices
connected to System
relays do not work.
7. CZM-1B6 reports a
trouble.
Incompatible notification
appliance connected.
Check P/N 315-096363 for a list of compatible notification appliances. Replace

incompatible devices.
Error in control logic functions.
Check the logic functions using the printout from CSG-M; correct and reload
the System from CSG-M into the SMB-2.
Power source for ouput

devices missing or not
connected.
Check that the power source is connected and that power is available.
Improper wiring of connected

devices.
Check that output devices are properly wired.
Connected devices are not

compatible with power source.
Check that power source and ouput devices are compatible.
No power to CZM-1B6.
On the SMB-2, check fuse F3. At the CZM-1B6 check power input; DC power must
be 16-31 VDC. Check polarity.
Wiring error on initiating

device circuit.
8. Modules in MOM-2/4 do
not work.
9. CSM-4 does not respond

to output logic
commands.
Check for opens or incorrect or missing end-of-line resistor (4.7K, W).
No power to MOM-2/4.
Check power cable connectors between the SMB-2 (P3) and the MOM-2/4 (P5).
Replace the power cable, if defective.
No communications between
SMB-2 and MOM-2/4.
Check communications cable connections between the SMB-2 (P6) and the
MOM-2/4 (P7). Replace the communications cable, if defective.
Modules are not properly

seated in edge connectors.
Remove and reseat all modules.
Modules are not properly

addressed.
Address the modules correctly using the printed configuration from CSG-M (See
CSG-M Programming Manual, P/N 315-090381).
Fuses are blown.
Check wiring for shorts using the Field Wiring Checkout Guide (page 2-11). Replace
fuses.
CSM-4 is improperly
configured.
Check and correct the configuration using the installation instructions for the CSM-4
(P/N 315-090854) and the printed configuration from CSG-M (See CSG-M
Programming Manual, P/N 315-090381).
Incompatible notification
appliances are connected.
Check P/N 315-096363 for a list of compatible notification applicances. Replace

incompatible devices.
Check the logic functions using the printout from CSG-M; correct and reload
the System from CSG-M into the SMB-2 (See CSG-M Programming Manual,
P/N 315-090381).
Defective CSM-4.
Replace CSM-4.
4-3

TABLE 19
TROUBLESHOOTING GUIDE (Continued)
SYMPTOM
PROBABLE CAUSE
CORRECTIVE ACTION
10. CRM-4 does not

respond to output logic
commands.
Power source for device is

missing or not connected.
Check that the power source to the CRM-4 is connected and that power is available.
11. Zone troubles from

CZM-4.
Check the logic functions using the printout from CSG-M; correct and reload the
System from CSG-M into the SMB-2 ( See CSG-M Programming Manual, P/N
315-090381. )
Connected devices are

incompatible with power
source.
Check that the power source and output devices are compatible.
Defective CRM-4.
Replace CRM-4.
Errors in initiating device circuit

wiring.
Check for wiring errors using the Field Wiring Checkout Guide ( page 2-11) and the
installation instructions for the CZM-4 ( page 2-14) . Check that the end-of-line
capacitor is the proper value and is properly connected. Unused zones must have
end-of-line capacitors installed on MOM-2/4 screw terminals ( 50 MFD, 50 VDC
polarized electrolytic capacitor) . See the installation instructions for the CZM-4 ( page
2-14) .
Defective CZM-4.
Replace the CZM-4.
4-4
+D=FJAH
Walktest Operating
Instructions
INTRODUCTION
A Walktest of the MXL-IQ System enables

a qualified technician to test the operation
of input points on the MXL-IQ with or
without disabling the entire fire alarm
system. Testing can be either silent or with
audible feedback in the following ways:
1. Entire system
2. ALD loop (60 subaddresses)
3. CZM-4 module (4 zones)
4. Conventional zone (individual
CZM-1B6 or CZM-4 zone)
5. MOI-7 (MID-16) inputs (128
subaddresses)
If a printer is installed, a printed record of
the test is made.
The Walktest is available with MXL-IQ
Operating Software. You must enter your
1-5 digit password before you can use the
Walktest functions. Enter the Walktest
through the MXL-IQ Main Menu (See
Chapter 3, Operating Instructions).
The MXL-IQ Main Menu structure with
Walktest included is:
The table below shows the selections in the Walktest Menu and
their related help messages.
TABLE 20
Walktest Menu
WALKTEST
HELP MESSAGE
System wAUD
Test Full System with AUDs
Loop wAUD
Test ALD Loop/MOI-7 (MID-16 group)/CZM-4 Module wAUDs
LIST
Zone wAUD
Test CZM-4/CZM-1B6 Zone with AUDs
CONTROL
Sytem SIL
Silent Test Full System
TEST
Loop SIL
Silent Test ALD Loop/MOI-7 (MID-16 group)/CZM-4 Module wAUDs
WALKTEST
Zone SIL
Silent Test CZM-4/CZM-1B6 Zone
Cancel
Cancel Walktest in progress
Extend
Reset test timer to 4 hours left
MXL-IQ Main Menu

ACKNOWLEDGE
5-1
Walktest Operating Instructions
System w/AUD
Cancel
Select this option to walktest all CZM-4

zones, CZM-1B6 zones, MID-16 inputs, and
ALD inputs with audible feedback to the
technician. This mode inhibits the
MXL-IQ from annunciating real alarm
conditions.
Select this option from the menu while in

the Walktest mode to set the Walktest
timer at the 1 minute left in Walktest mark.
This allows the MXL-IQ to complete
Walktest sequencing on devices placed in
test (alarm) just before cancellation. The
MXL-IQ completes the final 60 seconds of
the Walktest as indicated in Walktest
Ending Sequence (See page 5-4).
System SIL
Select this option to walktest all CZM-4
zones, CZM-1B6 zones, MID-16 inputs, and
ALD inputs without audible feedback to the
technician. This mode inhibits the
MXL-IQ from annunciating real alarm
conditions.
Extend
Select this option from the menu while in
the Walktest mode to reset the Walktest
timer to the 4 hours remaining mark.
Loop w/AUD
Select this option to walktest input devices
on a specific ALD loop, MOI-7 (MID-16)
group, or on all four zones of a CZM-4 with
audible feedback to the technician. This
mode inhibits the MXL-IQ from annunciating real alarm conditions for the ALD
loop or CZM-4 conventional zones in
Walktest.
Loop SIL
Select this option to walktest input devices
on a specific ALD loop, MOI-7 (MID-16)
group, or all four zones of a CZM-4 without
audible feedback to the technician. This
mode inhibits the MXL-IQ from annunciating real alarm conditions for the ALD
loop or CZM-4 conventional zones in
Walktest.
Zone wAUD
Select this option to walktest an individual
conventional zone (CZM-1B6 or CZM-4
zone) with audible feedback to the technician. This mode inhibits the MXL-IQ
from annunciating real alarm conditions
for the conventional zone in Walktest.
Zone SIL
Select this option to walktest an individual
conventional zone (CZM-1B6 or CZM-4)
without audible feedback to the technician.
This mode inhibits the MXL-IQ from
annunciating real alarm conditions for
the conventional zone in Walktest.
5-2
WARNING
A device placed in Walktest is disconnected from its usual functions. Alarm
causing devices in Walktest DO NOT
CAUSE ALARMS until the MXL-IQ is
out of the trouble of Walktest.
Suggested Walktest
Procedure
In order to reduce the chance of problems,

the following procedure must be followed
before performing the Walktest.
1. Inform the person in charge of the MXL-IQ
fire alarm system that a Walktest is to be
performed and that part or all of the fire
detection system will be disabled. It is
also advisable (or may be required) to
notify the fire department of the test.
2. Use the MXL-IQs LIST menu to obtain a
printout of the device types and custom
messages for ALL modules to be
walktested.
3. Review the list with the person in charge
of the fire protection equipment to
ensure that the custom messages
provide adequate information for locating
and testing the devices in question.
4. Disable the ASD applications in the
system using ASD_Device in the TEST
menu prior to performing the walktest.

Once the test ASD device option has been
enabled using the test menu, the tester
should wait 3 minutes before attempting
to test the ASD devices. This will ensure
that the ASD R-Algorithm has been
disabled for the test. When the test is
complete, press ASD_Device again to
re-enable ASD R-Algorithm, or it will
automatically re-enable after 4 hours.
The System will not reset if the ASD
devices are still in the disabled state.
5. Initiate Walktest. Test devices in a
predetermined, orderly sequence.
6. When the Walktest is complete (timed
out/canceled), acknowledge the OUT
OF TROUBLE condition and reset the
MXL-IQ. When the system indicates
SYSTEM NORMAL, the test is complete.
WARNING: A device placed in Walktest is
disconnected from its usual functions.
Alarm causing devices in Walktest do NOT
cause alarms until the MXL-IQ is out of the
trouble of Walktest.
In both the silent (SIL) and audible (wAUD)
Walktest modes, information is displayed on
the Control Panel LCD and printed on the
printer (if a printer is installed). The audible
(wAUD) mode also provides audible feedback to the technician with the testing of each
input device. Audible feedback is NOT
included on circuits with zone coded audibles.
A system with only zone coded audibles
ALWAYS results in a silent Walktest.
NOTE: The Walktest Ending Sequence

(See page 5-4) occurs with audible warnings in the audible Walktest modes.
NOTE: The MXL-IQ will not allow a
walktest to be initiated if there are Alarms
or Supervisory events in the event queues.
Walktest the System

To place all CZM-4 zones, MID-16 inputs,
and ALD input devices in Walktest, follow
the procedure below:
Move the cursor to the S in System
wAUD for a Walktest with audible
feedback or to the S in System SIL for
a silent Walktest.
Press ENTER.
The following events take place:

- the PARTIAL SYSTEM DISABLE
LED lights
- the TROUBLE LED flashes
- the internal audible sounds
- the Walktest activated trouble for the
MXL-IQ records on the trouble list
- if a printer is installed, the trouble is
also printed
The LCD display on the MKB-4 reads:
In Walktest. Normal operation
disabled. ENTER to continue.
Press ENTER or wait 60 seconds and

the display reads:
Walktest expires in 4 hrs unless
canceled. ENTER to continue.
Press ENTER, or wait 60 seconds and

the MXL-IQ returns to the Walktest
menu. (The MXL-IQ is in system
Walktest.) The LCD indicates the time
remaining in Walktest in the last five
positions on the display. The time is
indicated in HH:MM (hours:minutes) until
less than one hour remains, then it is
indicated in MM:SS (minutes:seconds).
Locate the device to be tested and place
that device in alarm (or trouble). When
the event is reported to the MXL-IQ, the
following sequence occurs:
1. When the System is in the audible
Walktest mode, all silenceable and nonsilenceable audibles that are not already
active or disarmed sound the code,
depending on how the device is used in
the CSG-M. The codes are:
EVENT
CODE
ALARM
2 seconds on, then off
SUPERVISORY
2 one-second pulses (on-off)
TROUBLE
SECURITY
STATUS/OTHER
5-3

2. When a printer is installed, the printer
prints a message similar to the following:
WLK [event type] IN/OUT device
address time/date device type,
custom message, trouble type
(if applicable)
Move the cursor to the L in Loop wAUD

for a Walktest with audible feedback or
to Loop SIL for a silent Walktest.
Press ENTER.
The MXL-IQ prompts the user for the
module number to be tested.
3. The LCD displays the device address,

custom message, WLK IN/OUT [event
type], and device type for 8 seconds.
Enter the desired module network

address, including all leading zeros,
followed by ENTER.
4. If the ALD device has an LED, it turns on

for 30 seconds to provide additional
feedback to the technician.
If the network address entered is not an

ALD, MOI-7, or CZM-4, the message
Invalid type for Walktest is displayed for
2 seconds on the LCD. The display then
returns to the Walktest menu.
If the MXL-IQ detects multiple events, they

are automatically spaced 8-10 seconds
apart to allow for separation of the coding.
Up to five simultaneous events may be
queued for processing.
If the module type is an ALD, MOI-7, or

CZM-4 in the CSG-M, the following
events take place:
Walktest Ending Sequence
- the PARTIAL SYSTEM DISABLE LED

lights
NOTE: This sequence does not occur in

Silent Walktest.
When 5 minutes remain in Walktest, all

silenceable and non-silenceable audibles
that are not already active or disarmed cycle
on-off five times (1 second on) to indicate
that the Walktest will time out in 5 minutes.
This occurs in the audible mode only.
When 1 minute remains, event coding and
the processing of devices to the LCD are
suspended. If a device is alarmed, it is cycled
silently through the resetting sequence.
When 45 seconds remain, all silenceable
and non-silenceable audibles that are not
already active or disarmed cycle on-off until
Walktest times out. Do NOT continue to
walktest devices. This 45 second period
of no new Walktest events ensures that all
devices are reset when the Walktest timer
expires and the System returns to normal
operation. Alarming a device during this
period might result in the reporting of
erroneous events when the system
returns to normal operation.
Walktest Entire ALD Loop, MOI-7

(MID-16), or CZM-4 Module
To place an ALD loop of input devices, an
entire set of MID-16 (MOI-7) inputs, or all
four zones of a CZM-4 module in Walktest,
follow the procedure below:
5-4

module appears on the trouble list
- if a printer is installed, the trouble is also
printed
In Walktest. Normal operation

the display reads:
Walktest expires in 4 hrs unless

the MXL-IQ will return to the Walktest
less than 1 hour remains; then it is
Locate the device to be tested and place
that device in alarm (or trouble). When
the event is reported to the MXL-IQ, the
following sequence occurs:

depending on how the device is used in
the CSG-M. The codes are as follows:
EVENT
CODE
ALARM
SUPERVISORY
TROUBLE
SECURITY
STATUS/OTHER

(if applicable)

Walktest Ending Sequence

NOTE: This sequence does not occur in
Silent Walktest.
When 5 minutes remain in Walktest, all
silenceable and non-silenceable audibles
that are not already active or disarmed cycle
on-off five times (1 second on) to indicate
that the Walktest will time out in 5 minutes.
This occurs in the audible mode only.
When 1 minute remains, event coding and
the processing of devices to the LCD are
suspended. If a device is alarmed, it is cycled
silently through the resetting sequence.
When 45 seconds remain, all silenceable

and non-silenceable audibles that are not
already active or disarmed cycle on-off until
Walktest times out. Do NOT continue to
walktest devices. This 45 second period
of no new Walktest events ensures that all
devices are reset when the Walktest timer
expires and the System returns to normal
operation. Alarming a device during this
period might result in the reporting of
erroneous events when the system
returns to normal operation.
NOTE: If an alarm or supervisory is

reported from a device that is NOT in
Walktest, the Walktest is suspended
immediately. No further Walktest events
are annunciated or coded. The Walktest
remains running in the background of the
MXL-IQ until it times out or is canceled.
WARNING:
When performing a partial system
Walktest, DO NOT TEST any devices
that are not in the Walktest as this will
cause an alarm in the system.
Walktest Individual CZM-1B6 or CZM-4

Zone
To place an individual CZM-1B6 or CZM-4
zone in Walktest, follow the procedure
below:
Move the cursor to the Z in Zone wAUD
for a Walktest with audible feedback or
Z SIL for a silent Walktest.
Press ENTER.
The MXL-IQ prompts the user for the
module and device number to be tested.
Enter the desired network address,
including all leading zeros, followed by
ENTER.
If the network address entered is not a
CZM-4 or CZM-1B6 zone, the message
Invalid type for Walktest is displayed for
2 seconds on the LCD. The display then
returns to the Walktest menu.
If the module type is a CZM-1B6 or
CZM-4 zone in the CSG-M, the following
events take place:
5-5

- the PARTIAL SYSTEM DISABLE LED
lights


(if applicable)

zone records on the trouble list
- if a printer is installed, the trouble is also
printed
In Walktest Normal operation

the display reads:
Walktest expires in 4hrs unless

the MXL-IQ returns to the Walktest
less than 1 hour remains, then it is
Locate the device to be tested and
place that device in alarm (or trouble).
When the event is reported to the
MXL-IQ, the following sequence occurs:
depending on the device usage in the
CSG-M. The codes are as follows:
EVENT
CODE
ALARM
SUPERVISORY
TROUBLE
SECURITY
STATUS/OTHER
5-6

When 5 minutes remain, the system begins the
Walktest Ending Sequence (See page 5-5).
NOTE: If an alarm or supervisory is
reported from a device that is NOT in
Walktest, the Walktest is suspended
immediately. No further Walktest events
are annunciated or coded. The Walktest
remains running in the background of the
MXL-IQ until it times out or is canceled.
WARNING:
When performing a partial system
Walktest, DO NOT TEST any devices
that are not in the Walktest as this will
cause an alarm in the system.
+D=FJAH
History Log
The MXL-IQ history system has five major
parts. They are:
1. CSG-M options that control the type and
number of events the MXL-IQ records.
2. Logging lists that record MXL-IQ
hardware events.
3. Event viewing and listing in the MXL-IQ
through the MKB-4 and attached printer.
4. History removal and collation outside the
MXL-IQ.
5. Report generation and analysis on an
external PC.
CSG-M History Options
INTRODUCTION
The CSG-M gives the designer a set of

options to use for operating the history
system. The designer must first decide
whether or not to use the history option. If
he chooses to use it, he must select the
mode of logging and which event types to
include in the log. The History Recording
Options are selected from the Options,
System Message, Authorizations menu.
(See Screen 1.)
To access the history option, move the
cursor to highlight History Recording
Options and press ENTER. The history
recording option selection screen is then
displayed as shown in Screen 2, page 6-2.
Fire Protection Company Name

CSG-M Memory=2900 used, 316848 free
Options, System Message, Authorizations
CONFIG => TEST1

Other System Flags
History Recording Options
System Holidays
Press First Letter or Move Cursor to Highlight Selection, then ENTER
Screen 1
6-1
History Log

History mode ------------------->

Log alarms --------------------->
Log troubles ------------------->
Log supervisories -------------->
Log securities ----------------->
Log status --------------------->
Log verification --------------->
Log output --------------------->
Log resets --------------------->
Log block acks. ---------------->
Log audible changes ------------>
Log manual sens. changes ------->
Log logic sens. changes -------->
Log arm/disarm ----------------->
Log energize/deenergize -------->
Log time changes --------------->
Log passwords ------------------>
Log overrides ------------------>
Enable History Log Via MKB Menu >
CONFIG => TEST1
Small
YES
YES
YES
YES
NO
NO
NO
YES
YES
YES
NO
NO
YES
YES
YES
YES
NO
NO
Move Cursor to Select, ENTER to TOGGLE
ESC = Prev. Menu
Screen 2
Screen 2 shows the default conditions for

the history option when it is selected for the
first time.
Keep in mind that the external data base
may not contain all events that were ever
detected. The completeness of the data
base depends on whether the system
operator extracts all event log information
before it is lost.
Logging Methods
The MXL-IQ has two mutually exclusive

ways to log events:
1. Small list
2. Circular list
6-2
Small List Logging

In the small list logging mode, the MXL-IQ
stores up to 818 events (See Screen 3) in
non-volatile memory. Non-volatile memory
is memory that is not lost when the power is
removed.
When the event storage area becomes

80% full, a system trouble begins.
the trouble audible sounds
the trouble indicator lights
the message Event Log 80% full shows
on the LCD display
this trouble operates like any other
trouble in the system
When the event storage area becomes

90% full, a new system trouble begins.
History Log
the trouble audible sounds
the trouble indicator lights
the message Event Log 90% full shows
on the LCD display
this trouble operates like any other
trouble in the system
When the event log is full, an new trouble

condition occurs which causes the trouble
audible to activate.
the message Log FULL, Events will be
lost appears on the display panel
upon reset this trouble reappears,
replacing the 90% trouble message
when the log is full, all new events are
lost
This system encourages removing history
information into an external data base
before the log overflows.
Circular Logging
In the circular logging mode, the MXL-IQ
guarantees that the most current 500
events are stored in non-volatile memory.

Once all available storage is used, the
oldest history entries are replaced by newer
ones. It is assumed that the end user
selects this mode because he does not
wish to maintain an external history data
base. Therefore, only two warning troubles
are issued:
1. When the number of recorded events
reaches 80% of the total.
2. When the number of recorded events
reaches 90% of the total. Once this
trouble is acknowledged, it disappears
until 80% of events is reached in the
next cycle.
Using the circular logging mode does not
prevent the storage of history information
into an external data base. However, there
is a high probability of loosing old events
because of the limited warnings given when
events are about to be overwritten.
Beginning with MXL-IQ Rev. 6.0, the user
can suppress the Circular History Log Full
Trouble. This option must be set in CSG-M
and is only available if the history is in
circular mode.

DISPLAY MXL-IQ Panel Info
CONFIG => TEST1
MXL-IQ PANEL INFO:

MXL-IQ ROM Version ------------------->
MXL-IQ Main Board Version ------------>
MXL-IQ Minimum Allowable Board Ver.--->
RAM size ----------------------------->
EEROM size --------------------------->
MXL-IQ Dictionary Version ------------>
MXL-IQ Alt. Dictionary Version-------->
History Memory Available ------------->
IEC Storage Memory Available --------->
Rev. 1.00
2
Rev. 1.00
163840 bytes
114688 bytes
0
0
818 (11) elements (used)
8189 bytes
PROGRAMMING INFO:
Configuration Source Filename -------->
Configuration Size ------------------->
Last Programming Date ---------------->
Configuration Revision Level --------->
Programming Info CHECKSUM ------------>
TEST1
2802 bytes
Wed Mar 22 15:28:16 20XX
215
1085
ANY KEY TO CONTINUE
Screen 3
Display MXL-IQ Panel Info
6-3
History Log
Logging Item Selection
The system designer can log one or many
event types. The selection is determined by
the system requirements, the amount of
event storage, and the external data base
design. The following list summarizes event
types that can be selected.
* ALARMS
* TROUBLES
* SUPERVISORIES
* SECURITIES
STATUS CHANGES
DEVICE VERIFICATION
OUTPUT ACTIVATIONS
* RESET
* BLOCK ACKNOWLEDGE
* AUDIBLE CONTROL
SET SENSITIVITY
AUTO SET SENSITIVITY
* ARM/DISARM
* ENERGIZE/DE-ENERGIZE
* SET TIME
System Message Authorization, then select

History Recording Options. From History
Recording Options, move the cursor down
to the line that reads Enable History Log Via
MKB Menu, and select YES to compile the
CSG-M program and download it to the
MXL-IQ. (Refer to Screen 2.)
From the MKB Menu

Go to the TEST menu, move the cursor to
the right until it highlights the Event-Log
Menu item, and press Enter to bring up the
submenu for MXL History. Move the cursor
within the submenu to either the left or right
to highlight the Hist_Ctrl item to turn on/off
the History, or Hist_Erase to erase History.
Notice that if the CSG-M system option
Enable History Log Via MKB Menu is set
to NO, these submenus are not accessible.
History turned on or off using the MKB
menus is unaffected through PANEL
RESET, and defaults to the setting in
CSG-M upon power-up.
Pressing ENTER while the cursor is on
Hist_Erase displays the following message
on the MKB asking for confirmation:
Enter to proceed, other key to
abort
* PASSWORD
OVERRIDE
*The items marked with an asterisk are set
as default when the logging option is first
selected. At least one event type must be
selected.
MKB Menu Option to

Enable, Disable and Erase
History
Effective with MXL-IQ Revision 6.0, this

option allows the user with the highest level
password to turn on, turn off, or erase the
History, provided that this system option
has been enabled in the CSG-M and the
History mode is other than NONE (that is,
either small or circular).
Enabling the History Option in CSG-M

From the Main Menu, select System
Configuration Edit, then select Options,
6-4
Pressing ENTER erases the History section

in the flash no matter what state the History
is currently in (manually turned on or off);
pressing any other key aborts the action.
Manual manipulation of History using the
MKB is logged in History as in the following
examples:
History Manually Erased
History Manually Turned off
History Manually Turned on
NOTES:
1. The operator should download the
history log for future reference before
erasing the MXL-IQs History, since once
the history is erased it cannot be
undeleted.
2. The history menu options do not alter the
history mode selected in the CSG-M.
History Log
Local History Log Query
There is a limited set of query selection and

filter options available within the MXL-IQ.
More complex options are only possible
using an IBM PC that is running the
MXL-IQ history support program.
The user can get history log information
from the MKB-4 control panel by choosing
the TEST menu, selecting EVENT_LOG,
and pressing ENTER. A submenu of filter
selections is then displayed. The choices
are as follows:
Alrm_Only
Only display or print
alarm events
Trbl_Only
Only display or print
trouble events
Superv_Only Only display or print
supervisory events
Security_Only Only display or print
supervisory events
All_events
Display or print all
recorded history events
Hist_Ctrl
Use to turn History
on/off
Hist_Erase
Use to Erase History
If the user makes a selection from the
filter menu using the ENTER key of the
MKB-4, the output goes to the LCD
display.
If the filter menu is selected using the
PRINT key of the MKB-4, then the output
goes to the system printer.
If the group of events selected is empty,
then the MXL-IQ displays or prints, as
appropriate, NO HISTORY ITEMS
FOUND.
Cursor left or right until the desired filter

type (See Query Filters, below) is reached
and then press ENTER to display to the
LCD, or PRINT to print on the MXL-IQ
system printer.
The MXL-IQ asks for a starting date and
time. If a time is entered, it suppresses the
display or printing of older events. This
initial display of time and date indicates the
oldest history event recorded in memory. If
the operator presses the ENTER key
without making any numeric input, then all
events in the log are selected.
Query Filters
A limited set of event type filters is available
from the MXL-IQ control panel. The mutually exclusive filters are:
ALARMS
The Alrm_Only filter selection displays
or prints incoming alarms, alarm acknowledgments, audible control, and resets.
This set of events gives the operator a
clear picture of the important events that
constitute an alarm condition.
TROUBLES
The Trbl_Only filter displays or prints
troubles and resets.
SUPERVISORIES
The Superv_Only filter displays or prints
supervisories and resets.
SECURITIES
The Security_Only filter displays or prints
securities, device arms, device disarms,
and resets.
ALL
The All_events filter displays or prints all
events.
Query Selection
The MXL-IQ supports one query selection
option when generating listings or printouts
from the MXL-IQ control panel.
HISTORY ON/OFF
The Hist_Ctrl filter turns the History events
on/off.
From the TEST menu, move the cursor to

the EVENT_LOG item and press the
ENTER key to select history information.
The MXL-IQ responds with a submenu that
allows an event type filter to be selected.
HISTORY ERASE
The Hist_Erase filter erases the History
events.
6-5
History Log
Navigating The History

Display
When the operator selects the LCD display

mode, the NEXT and HOLD keys are used
to navigate through the log list. When the
history log list first displays, the oldest history
event shows in the display. Use the NEXT
key to select the next newest event in the list
and the HOLD key to select the next oldest
event in the list. When either end of the
history log list is reached, the message End
of History List displays. Continuing to press
either key wraps the list to the oldest or
newest event, as appropriate.
001001
The module/device address. The division
sign indicates that this is a history log
display.
1ST FLOOR EAST WING
The custom message assigned to this input.
321
The history log sequence number.
ACK
Optional field indicating that this is an
acknowledgment event. This field is blank
when the initiating event is displayed.
The MXL-IQ remains in the history log list

display mode until the up arrow key is
pressed. As with all menu operations, if no
keys are depressed for one minute, the
current activity is canceled.
12:24:48 Mar 10, 20XX

The time that the event was logged.
History Display Formats
IN
History events display one at a time, in

reverse chronological order, with the oldest
event displayed first. History event displays
use both lines of the LCD.
OUT DEVICE REPORTS RETURN TO

NORMAL STATE
A division symbol () in the first line of the

display gives the operator a quick visual
cue that the MXL-IQ is in the history display
mode. If the history event begins with a
module/device (mmm/ddd) code, the
display is formatted as:
mmmddd
IN
The event direction. The possible event
direction types are:
ON
DEVICE REPORTS ACTIVE STATE
DEVICE TURNED ON
OFF DEVICE TURNED OFF

DIS
DEVICE DISARMED (always occurs

with ARM)
ALR
The event type. The possible abbreviations
for Device Event types are:
ALR
ALARMS
TBL
TROUBLES
If the line begins with an event type name,

such as Block Acknowledge, then the first
line of the display reads:
SUP SUPERVISORY
mmm
SAT
STATUS
VFY
VERIFY
BLOCK ACKNOWLEDGE
where mmm is the module number of the

MKB-4 or SMB that caused the event.
Device Event
A device event is any alarm, trouble, supervisory, or security input change of state. This
change of state can be into or out of an
active condition. The LCD displays:
001001 1ST FLOOR EAST WING ACK
321 12:24:48 Mar 10,20XX IN ALR
6-6
Where:
SEC SECURITY
DEV DEVICE (used for ON and OFF

indications)
ARM DEVICE ARMED (disarmed when
used with DIS)
Reset Event
A reset event is any cold, warm, manual, or
watchdog reset. The LCD displays:
History Log
253
10100
WATCHDOG RESET
1:22:04 Mar 10,20XX
Where:
253
The module address where the reset
occurred. In this example, the watchdog
reset originated on the SMB-2 at fixed
address 253. The division sign indicates
that this is a history log display.
WATCHDOG RESET
The message describing the type of reset
that occurred. The possible messages for
this field are:
COLD RESET
WARM RESET
MANUAL RESET
WATCHDOG RESET
10100
1:22:04 Mar 10,20XX
SET TIME
The message describing this display as a
set time event.
10100
2:00:30 Mar 10, 20XX
The date and time in the MXL-IQ before the
SET TIME function was performed.
2:10:45 Mar 10, 20XX
The time when the event was logged. Note
that this is also the new date and time in
the MXL-IQ as a result of this operation.
Block Acknowledge Event

A block acknowledge event occurs when
the alarm, trouble, supervisory, or security
acknowledge key is actuated on an MKB-4
in a system that allows block acknowledgments. The LCD displays:
251
All Alarms Acknowledged
4211 11:25:14 Mar 11,20XX
Where:
Set Time Event

A set time event records any change to the
MXL-IQ real time clock. There are two
occasions when a set time event occurs.
They are:
1. When an operator goes into the TEST
menu and manually changes the real
time clock using the SET_TIME function.
2. At the end of a CSG-M configuration
upload.
The LCD displays:
251 SET TIME - 2:00:30 Mar 10,20XX
10100 2:10:45 Mar 10,20XX
Where:
251
The module address where the time
change occurred. In this example, the set
time originated from the MKB-4 at address
251. The division sign indicates that this is
a history log display.
251
The module address where the block
acknowledge occurred. In this example, the
block acknowledge originated from the
MKB-4 at address 251. The division sign
indicates that this is a history log display.
The message that describes this display
as an alarm block acknowledge event. The
text changes to reflect one of the following
four types of block acknowledgments, as
appropriate:
All Troubles Acknowledged
All Supervisories Acknowledged
All Security Acknowledged
4211
11:25:14 Mar 11, 20XX
6-7
History Log
Audible Silenced Event

This event occurs when the audible silence
key is actuated on an MKB-4. The LCD
displays:
251
AUDIBLE SILENCED
4212 11:25:14 Mar 11,20XX
OVERRIDE
The action that is being applied to the
feature. The selections in this field are:
OVERRIDE
NORMAL
4212
Where:
11:25:14 Mar 11, 20XX

251
The module address where the audible
silence occurred. In this example, the
audible silence originated on an MKB-4 at
address 251. The division sign indicates
Audible Unsilenced Event
AUDIBLE SILENCED
The message that describes this event.
4212
11:25:14 Mar 11, 20XX
Override Event
This event occurs when an operator
overrides a verification or confirmation. The
LCD displays:
251
CONFIRMATION OVERRIDE
4212 11:25:14 Mar 11,20XX
This event occurs when the audible

unsilence key is pressed on an MKB-4. The
LCD displays:
251
AUDIBLE UNSILENCED
4213 11:25:14 Mar 11,20XX
Where:
251
The module address where the audible
unsilence occurred. In this example, the
audible unsilence originated on an MKB-4
at address 251. The division sign indicates
AUDIBLE UNSILENCED
The message that describes this event.
4213
11:25:14 Mar 11, 20XX
Where:
251
The module address where the override
operation occurred. In this example, the
confirmation override originated on an
MKB-4 at address 251. The division sign
CONFIRMATION
The feature that is either being overridden
or returned to normal. This selections in
this field are:
CONFIRMATION
VERIFICATION
6-8
Password Event
This event occurs when an operator enters
a new password at an MKB-4. The LCD
displays:
251
PASSWORD LEVEL : 1
4214 11:25:14 Mar 11,20XX
Where:
251
The module address where the password
event occurred. In this example, the
History Log
password change originated on an MKB-4
at address 251. The division sign indicates
PASSWORD LEVEL : 1
The message that describes this as a
password event and indicates the new
password authorization level that was
entered.
4214
11:25:14 Mar 11, 20XX
Configuration Changed Event

This event occurs when an operator
uploads a new CSG-M configuration to the
MXL-IQ control panel. The LCD displays:
254
Configuration changed 10->11
4214 11:25:14 Mar 11,20XX
Where:
254
The module addres where the configuration
change occurred. In this example, the
configuration change originated from the
field programmer at address 254. The
division sign indicates that this is a history
log display.
Configuration changed
The message that describes this as a
configuration change event.
10
The old configuration modification sequence number.
11
The new configuration modification sequence number.
Note: These values may not be consecutive. They depend on the number of modifications made to the configuration by the
CSG-M.
4214
11:25:14 Mar 11, 20XX
Manual Sensitivity Set Event

A sensitivity set event displays any change
of sensitivity to a detector device that was
made manually at a system control panel.
The LCD displays:
001001 1ST FLOOR EAST WING
321 12:24:48 Mar 10,1995
NORMAL
Where:
001001
display.
1ST FLOOR EAST WING
The custom message assigned to this input.
321
12:24:48 Mar 10, 20XX
NORMAL
The sensitivity value sent to the device. The
selectable values include:
Hi_3
Hi_2
Hi_1
NORMAL
Low_1
Low_2
Low_3
Auto Sensitivity Set Event

of sensitivity to a detector device made by
the auto sensitivity adjustment system. The
LCD displays:
001001 1ST FLOOR EAST WING
2.12 +
321 12:24:38 Mar 10, 20XX
Where:
001001
display.
1ST FLOOR EAST WING
The custom message assigned to this
input.
6-9
History Log
321
2.12
Indicates that this is an IEC (Enviro-Link)
set sensitivity event. The detector sensitivity
has been set to 2.12 volts. (The voltage can
range from 0-5 volts.) This field may
contain the word CLEAN to indicate that
this detector was cleaned and restored to
its base sensitivity.
+
This symbol represents the type of automatic correction that was made. A plus sign
(+) indicates that the sensitivity was increased, a minus sign (-) indicates that the
sensitivity was decreased.
12:24:48 Mar 10, 20XX
Logic Sensitivity Set Event
History Print Formats At

The MXL-IQ Panel
The history printout format available at the

MXL-IQ control panel appears in the same
format as all other listing type reports. The
listing output is in the higher character
density mode of the output device. The
vertical pitch varies to clearly distinguish
one event from another. If the target printer
has variable point spacing, each event is
separated by a 0.5 line gap. On printers
without variable point spacing, there is one
full blank line between events.
To interrupt the listing operation at any
time, press the CLEAR key. Significant
system activities, such as alarms, troubles,
etc., automatically terminate the listing. The
printout always indicates when the listing
has been prematurely terminated.
(Refer to the History Log Sample Printout on the following page)
The basic format of the history printout is:

of sensitivity to a device made by output
logic. The LCD displays:
<Listing Date>
FN0012 Sensitivity set by logic

321 12:24:48 Mar 10,20XX
NORMAL
<Event Type [Modifier]>

<Event Locator>
<Event Time>
<Event Sequence #>
<Event Description>
Where:
<Listing Conditions>
FN0012
The label of the logical function that generated this sensitivity set. The division sign
SENSITIVITY SET BY LOGIC

The message describing this as a logic
sensitivity set event.
(repeated for each event having

matching conditions)
<Listing Terminator>
321
12:24:48 Mar 10, 20XX
NORMAL
The sensitivity value sent to the device.
Hi_3
Hi_2
Hi_1
NORMAL
Low_1
Low_2
Low_3
6-10
Where:
Listing Date
Identifies the report type (in this case the
history log) and the date that the report was
generated.
Listing Conditions
Shows the filter and starting date for this
report.
History Log
History Log Sample Printout
1
Line 1
Line 2
10
20
30
40
50
Listing of History Log at 14:32:22 Apr 04,20XX
This is a FULL list beginning at 09:20:02 Mar 01,20XX:
60
70
80
Line 3
SENS NORM. FN0012
06:00:00
Mar 02,20XX
#1
Sensitivity set by output logic
Line 4
SENS Hi_1 FN0013
19:00:00
Mar 02,20XX
#2
Line 5
Line 6
TROUBLE IN 1-1
22:10:11
Mar 02,20XX
#3
Response Too Low, TRI-2R Switch Input + Relay
UTILITY CABINET, Input Dev.
Line 7
ACK. TRBL. 251
22:15:24
Mar 02,20XX
#4
Troubles Block Acknowledged
Line 8
MAN. RST. 251
22:50:03
Mar 02,20XX
#5
Manual Panel Reset
Line 9
SENS NORM. FN0012
06:00:00
Mar 03,20XX
#6
Line 10
SENS Hi_1 FN0013
19:00:00
Mar 03,20XX
#7
Line 11
Line 12
VERIFY
2-11
21:39:00
Ionization Detector
Mar 03,20XX
#8
ROOM 101 FIRST FLOOR, ID-60I
Line 13
SENS NORM. FN0012
06:00:00
Mar 04,20XX
#9
Sensitivity set by logic
Line 14
Line 15
VERIFY
12-23
10:42:20
Ionization Detector
Mar 04,20XX
#10
ROOM 221 SECOND FLOOR, ID-60I
Line 16
Line 17
ALARM IN 12-23
10:43:12
Ionization Detector
Mar 04,20XX
#11
Line 18
OUTPUT ON FN0103
10:43:13
Mar 04,20XX
#12
Output logic operation
Line 19
OUTPUT ON FN0010
10:43:13
Mar 04,20XX
#13
Output logic operation
Line 20
ACK. ALARM 251
10:45:21
Mar 04,20XX
#14
Alarms Block Acknowledged
Line 21
SILENCE
10:45:22
Mar 04,20XX
#15
Audibles silenced
Line 22
MAN. RST. 251
10:45:25
Mar 04,20XX
#16
Manual Panel Reset
Line 23
LOGIN 2
10:50:53
Mar 04,20XX
#17
Operator Login to Level 2
Line 24
Line 25
DISARM
12-23
10:51:23
Ionization Detector
Mar 04,20XX
#18
Line 26
DISARM
10:52:04
Mar 04,20XX
#19
FAN #1, CRM-4 Relay Output
Line 27
ENERGIZE
10:52:24
Mar 04,20XX
#20
FAN #1, CRM-4 Relay Output
Line 28
SENS HIGH FN0013
19:00:00
Mar 04,20XX
#21
Sensitivity set by logic
251
251
7-2
7-2
6-11
History Log
Event Type
Identifies the type of history event that is
being reported. The following event types
are arranged in groups. The modifier fields
for each group are different.
Group 1 types:
ACK. ALARM Alarm block acknowledge
SUPERVS
Security causing device

event
Supervisory causing device
event
Group 3 types:
SENS
Sensitivity set
ACK. TRBL.
Trouble block acknowledge
Group 4 types:
LOGIN
Operator login
ACK. SEC.
Security block acknowledge
Group 5 types:
OUTPUT
Output logic event
ACK. SUP.
Supervisory block acknowledge
MAN. RST.
Manual reset via MKB-4
COLD RST.
Hard reset from power off
WARM RST.
Hard reset via reset jumper
WDOG RST.
Hard reset via 6805

watchdog
VERIFY
Alarm verify
ENERGIZE
Energize an output
DE-ENERGIZE De-energize an output
6-12
SECURTY
ARM
Arm a device
DIS-ARM
Disarm a device
SILENCE
Silence audibles
UNSILENCE
Unsilence audibles
CONFIG.
(CSG-M) Configuration
changed
Modifier
The modifier is an optional field that
extends the meaning of the event type. For
example, ALARM IN, where IN explains the
ALARM type.
Group 1 type:
No modifiers for this group
Group 2 types:
IN
Condition now active
OUT
Condition now inactive
ACK
Condition now acknowledged
Group 3 types:
Hi_3
Hi_2
Hi_1
NORMAL
Low_1
Low_2
Low_3
Group 4 types:
0
Lowest access
1
2
3
Highest access
Group 5 types:
Group 2 types:
ALARM
Alarm causing device
event
ON
Condition now active
OFF
Condition now inactive
TROUBLE
Event Locator
This field locates the source or destination
Trouble causing device

event
History Log
of the event as either a module number,
module-device pair, or function name.
Event Time
The time and date of this event.
Event Sequence #
The sequence number of this event in the
history log list. The maximum value of this
number depends on the type of logging
selected and the length of time since the
last download.
Event Description
The event description is either the custom
message associated with a device, or for
non-devices, it is a descriptive message.
MXL-IQ To CSG-M
Download Formats
Download from the MXL-IQ history log to

the CSG-M history support feature occurs
while the MXL-IQ maintains all normal
operations. There are two ways to access
history log events:
1. Non-destructive modeinformation
can be examined only.
2. Destructive modeinformation can be

extracted from the MXL-IQ and
incorporated into a data base (See
Screen 4). If the information is extracted
from the MXL-IQ, the history is erased
from the system, and the system is
reset. Access to the destructive mode is
password and vendor ID protected.
The history contents and organization of
the CSG-M configuration change over the
lifetime of the system. As a result, the
history extraction process must download
both the encoded history log and its configuration in the CSG-M. At the conclusion
of the extraction process, an .IMH file is
created which contains fixed data that is
common to all history extractions from a
given CSG. This technique has the advantage of eliminating the need for a complex
code in the MXL-IQ to reorganize the data,
shifting that burden to programs in the PC
environment which are more easily modified. However, this technique requires time
to perform the download.
Each access of the history, whether in the
examine or extract mode, requires the
transmission of the entire CSG-M configuration from the MXL-IQ to the PC host. For
very large configurations, this could take
many minutes for the first download after a

CONFIG => TEST1
Transfer a System to or from an MXL-IQ Panel
SEND System Configuration TO MXL-IQ Panel

READ System Configuration FROM MXL-IQ Panel
VERIFY System Configuration in MXL-IQ Panel
DISPLAY MXL-IQ Panel Info
EXTRACT MXL-IQ Panel History
Move Cursor to Highlight Selection, then ENTER
ESC=Prev. Menu
Screen 4
Transfer a System to or from an MXL-IQ Panel
6-13
History Log
4. The PC creates a raw data file that

contains an identifying header.
History Download Sequence
5. The PC downloads the compressed

history log data and appends it to the file.
The download process uses the existing

capabilities of the CSG-M programming
system. The sequence for extracting history
log events is as follows:
1. PC contacts the MXL-IQ and requests
the configuration header and data area
pointers.
2. If the PC determines that there is history
data present, then the extraction process
begins.
3. The PC computes the required amount
of storage and determines if the media in
the PC has enough room for it. If there is
sufficient room, the process continues; if
6-14
not, the user is prompted to change

disks.
configuration is changed. If the .IMH file is

present after the first download of a configuration, the operation will run more
quickly on subsequent downloads.
6. The PC downloads the configuration

data and appends it to the file.
7. The resulting file is closed and then
tested for integrity. Any irregularity in this
validation ends the extraction process
and signals the user.
8. If this is a non-destructive download,
then the process is complete.
If this is a destructive download, then

the clearing of the history log in the
MXL-IQ begins. A warm reset occurs in
the MXL-IQ at the end of the extraction
process.
+D=FJAH
Connections and Ratings
ALD-2I Connections and Ratings

Electrical ratings:
Supervisory
Alarm
30 VDC peak
66mA max
30 VDC peak
66mA max
(60 devices in alarm)
All wiring must be in accordance with

Article 760 of NEC and the local building
codes.
Only the devices listed in Appendix A,
Table 2 - Analog Addressable Detectors on page A-1 may be used. The UL
identifiers for compatibility are the same as
the model names specified.
See Notes 7 and 11.

See Note 8.
ALD-2I Wiring
NOTES
1. Power limited to
NFPA 70 per NEC 760.
2. Minimum wire size:
18 AWG.
3. Maximum resistance:
100 ohms total.
4. Maximum capacitance:
0.4F between
+ loop and loop.
0.8F between
+ loop and chassis.
0.8F between
loop and chassis.
5. Each detector or group of
detectors, requires a
two-wire circuit of
thermo-plastic fixture
wire enclosed in conduit
or limited energy
shielded cable without
conduit, if permitted by
local building codes.
6. No end of line device
required.
7. Operates in full
conformance with
Style 6.
8. Operates in full
conformance with
Style 4.
9. Either loop may be wired
Class A or B.
10. 60 devices maximum per
loop.
11. T-tapping is NOT
allowed on Class A
loops.
12. Both circuits are
supervised.
7-1
ALD-2I Connections and Ratings
7-2
CMI-300 Connections and Ratings

Electrical ratings:
Supervisory or Alarm
5 VDC, 96mA max
TYPICAL CLASS B (STYLE 4)

CONNECTION
2-WIRE
18 AWG
CABLE MIN*
TB1
TB2
LLM-1
LLM-1
4
* USE 2-WIRE COPPER CABLE, 105 C, 300V, 18 AWG,
TB2
TB1
MOM-2/4
CXM-1
NOTES
1. All wiring must conform
to local codes and to the
authority having
jurisdiction over the
installation.
2. All circuits are rated
2 volts peak to peak,
1.3mA. All circuits are
supervised.
3. Operates in full
conformance with
Style 4.
SOLID OR STRANDED, MAX 7 STRANDS.
CMI-300 Wiring - Typical Class B (Style 4) Connection
7-3
CMI-300 Connections and Ratings
TYPICAL CLASS A (STYLE 7)

CONNECTION
TB1
TB1
MOM-2/4
4
LLM-1
TB2
TB2
LLM-1
*USE 2-WIRE
COPPER CABLE,
105 C, 300V, 18 AWG,
SOLID OR STRANDED,
MAX 7 STRANDS.
TB1
NOTES
1. All wiring must
conform to local codes
and to the authority
having jurisdiction
over the installation.
supervised.
3. Operates in full
conformance with
Style 7.
TB1
TWO 2-WIRE 18 AWG CABLE MIN*

600 OHM MAX LINE RESISTANCE
TOTAL PER PAIR
LLM-1
TB2
TB2
LLM-1
CXM-1
CMI-300 Wiring - Typical Class A (Style 7) Connection
CONDITIONED NON-SWITCHED
LEASED TELEPHONE LINE,
600 OHMS IMPEDANCE
TYPICAL CLASS B (STYLE 4)
CONNECTION
R1
560 OHMS,
1/2W, 5%
P/N 140-820366
TB1
LLM-1
4
R2
CXM-1
CMI-300 Wiring - Typical Class B (Style 4) Connection

Using Conditioned, Non-Switched Telephone Line
7-4
LLM-1
TB2
TB1
MOM-2/4
TB2
NOTES
1. All wiring must
having jurisdiction
over the installation.
supervised.
3. Operates in full
conformance with
Style 4.
CRM-4 Connections and Ratings

Electrical ratings:
24 VDC
15mA (no energized relays)
Add: 18.7mA per energized relay
(75mA - all relays energized)
MOM-4
(TB-1, TB-2, TB-3, or TB-4)
or
MOM-2
(TB2 or TB4)
CRM-4 Relay Wiring
NOTES
1. Contact rating: 2A,
30VDC/120 VAC
resistive.
2. Use only with power
limited / Class 2
circuits.
3. Coils are supervised
when de-energized.
4. Contacts are not
supervised.
5. All relay contacts are
shown in normal
(de-energized) state.
7-5
CRM-4 Connections and Ratings
7-6
CSM-4 Connections and Ratings

Electrical ratings:
Only the devices listed in Compatible

Notification Appliances, P/N 315096363 may be used. The UL identifiers
for compatibility are the same as the
model names specified.
Supervisory
24V unfiltered,
full wave rectified
12mA max
Alarm
24V unfiltered,
full wave rectified
1.5A max
NOTIFICATION APPLIANCES
(NFPA 72 Local)
Article 760 of NEC and the local building codes.
STYLE Y
(CLASS B)
STYLE Z
(CLASS A)
CIRCUIT 1
CIRCUIT 2
2.2K, 1/2W
NOTIFICATION
APPLIANCES
+
MOM-4 (TB1, TB2, TB3, or TB4)
or
MOM-2 (TB2 or TB4)
2.2K,
1/2W
NO CONNECTION
+
1
NO CONNECTION
10 11 12
13 14 15 16
NOTES
1. Power limited to
18 AWG.
3 ohms total.
4. End of line device:
2.2K, W,
P/N 140-820380.
5. Either circuit may be
wired Class A or B.
supervised.
7. Polarity shown in
supervisory state.
CSM-4 Loop Wiring for Supervised Notification Appliance Circuit
7-7
NOTES
1. Both circuits are not
power limited.
2. The total loop
resistance from the
LLM-1 to the Municipal
Tie, including the 14.5
ohms in the Municipal
Tie, should not exceed
22.5 ohms.
used.
supervisory state.
MUNICIPAL TIE
(NFPA 72 Municipal Tie)
codes.
Electrical ratings:
Trip Coil
14.5 ohms
Trip Current
220 to 320mA
DC (momentary)
Supervisory
Current
Voltage
12mA DC
24V unfiltered,
full wave rectified
Minimum emergency power

60 hour standby
5 minute alarm
MOM-4 (TB1, TB2,

TB3,or TB4)
or
MOM-2 (TB2 or TB4)
CSM-4 Loop Wiring for Supervised Municipal Tie
LEASED LINE
(NFPA 72 Remote Station)
codes.
When a CSM-4 circuit is used as a Leased

Line trouble output, SW1 and SW2 on
switch S2 must be set. These positions
permit the degrade trouble bus to activate
the trouble line.
Electrical Ratings:
24V unfiltered, full wave rectified
Load must be a compatible polarity
reversal labeled remote station
receiver unit
Rated current
3mA to 9mA, alarm/supervisory
External circuit resistance
2K to 5K ohms
Minimum emergency power
60 hour standby
5 minute alarm
7-8
NOTES
1. Power limited to
2. External resistance:
2K-5K ohms.
3. Both circuits are not
supervised.
supervisory state.
MOM-4 (TB1, TB2,

TB3,or TB4)
or
MOM-2 (TB2 or TB4)
CSM-4 Leased Line Circuit Wiring
RELEASING SERVICE (Per NFPA 12A,

NFPA 13, and NFPA 2001)
Electrical Ratings:
Solenoids
24 VDC
16.8 watts max
700mA max
Supervisory
12mA max
Alarm
800mA max

codes.
Set all positions of switch S2 to OFF
(OPEN).
Application
NFPA 13
(Pre-Action
Deluge)
Make
Skinner
Model
LV2LBX25, 24V
ASCO
T8210A107, 24V
ASCO
R8210A107, 24V
ASCO
8210A107, 24V
NFPA 12A
Pyro
50 0-982631, 24V
Pyro
50 0-286652, 24V
(Halon)
Pyro
50 0-083377, 24V
Pyro
50 0-086929, 24V
Pyro
ECHS-24 EXP
NFPA 20 01
(FM-20 0)
NOTES
1. Releasing zones are
not power limited.
3 ohms total.
required.
supervised for opens
only.
5. Polarity show in
supervisory state.
MOM-4 (TB1, TB2,

TB3,or TB4)
or
MOM-2 (TB2 or TB4)
CSM-4 Loop Wiring for use as Releasing Service

(per NFPA 12A, NFPA 13, and NFPA 2001)
7-9
7-10
NOTES:
1. Use only listed solenoids from the following table:
Application
NFPA 13
(Pre-Action
Deluge)
Make
Skinner
Model
LV2LBX25, 24V
ASCO
T8210A107, 24V
ASCO
R8210A107, 24V
ASCO
8210A107, 24V
NFPA 12A
Pyro
50 0-982631, 24V
Pyro
50 0-286652, 24V
(Halon)
Pyro
50 0-083377, 24V
Pyro
50 0-086929, 24V
Pyro
ECHS-24 EXP
NFPA 20 01
(FM-20 0)
2.
3.
4.
5.
Solenoids supervised for opens only.

Polarity shown in supervisory condition.
Releasing circuits are not power limited.
No end-of-line device used on Pre-Action/Deluge or
releasing circuits.
6. Configure CSM-4 Pre-Action/Deluge circuits as
Municipal Tie.
7. Maximum of 4 zones per MOM-2.
8. Each MOM-2 must be powered from a separate
ALARM-SAF power supply.
9. Set all positions of S2 on the CSM-4 to OFF (OPEN).
MXL-IQ Releasing Service Wiring Diagram Using MOM-2 (NFPA 12A, 13, and 2001)
MOUNT VAI-1 AND TRI-60/B6 IN ALARM - SAF CABINET
VAI-1
24 VAC
+
BATTERY _
1
2
3
4
TRI-60/B6
8 7 6 5 4 3 2 1
N N N
C C C
1 2 3 4
CHASSIS
CHASSIS
120 VAC
INPUT
END OF LINE
RESISTOR
3.6K, 1/4W
P/N 140-820185
CHASSIS
NEUTRAL
HOT
DC OUT
+
_
FAULT
+
_
1
2
3
4
ALARM - SAF
MODEL AS/PS5-BFS-24-UL
UL GUIDE UTRZ
FILE NO. S3584
(Pre-Action
Deluge)
NFPA 12A
(Halon)
2.
3.
4.
5.
6.
Make
Skinner
Model
LV2LBX25, 24V
Maximum #
per MOM-4
5
ASCO
T8210A107, 24V
ASCO
R8210A107, 24V
ASCO
8210A107, 24V
Pyro
50 0-982631, 24V
Pyro
50 0-286652, 24V
Pyro
50 0-083377, 24V
Pyro
50 0-086929, 24V
Pyro
ECHS-24 EXP
Solenoids supervised for opens only.

Polarity shown in supervisory condition.
Releasing circuits are not power limited.
No end of line device used.
Each MOM-4 must be powered from a separate
ALARM-SAF power supply.
7. Set all positions of S2 on the CSM-4 to OFF (OPEN).
12 VDC LEAD ACID

BTX-1 31 AH
SOLENOID
SOLENOID
+
12 VDC LEAD ACID
BTX-1 31 AH
SOLENOID
SOLENOID
TO SMB-1/-2 P6
N N
C C
N N N N
C C C C
N N N N
C C C C
N N
C C
TB1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
P1
CSM-4
P2
CSM-4
N
C1
P5
N N
C C
2 1
N N N N
C C C C
N N
C C
TB3
TB6
P7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
P3
CSM-4
P4
DO NOT USE
MOM-4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
P8
TB2
N N
C C
N N N N
C C C C
N N
C C
N N N N
C C C C
N
C
TB7
2 1
N N
C C
N N N N
C C C C
P10
2
NC
1
NC
TB5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
TB4
DO NOT USE
2.2K, 1/2W
P/N 140-820830
7-11
SOLENOID
MXL -IQ Releasing Service Wiring Using MOM-4 (per NFPA 12A, NFPA 13, and NFPA 2001)
N N N N N N N N N N N N N N N N
C C C C C C C C C C C C C C C C
For FM Approved
Deluge/Pre-Action:
All initiating devices
connected to the
system MUST be
wired Class A.
NFPA 20 01
(FM-20 0)
To Analog loop on MMB-1/2

or ALD-2I. Program TRI-60/B6
+
_ as trouble causing program
for normally open operation.
Refer to TRI-60 Installation
Instructions, P/N 315-092329
and TRI-B6 Installation
Instructions, P/N 315-093315.
BATTERY ENCLOSURE
UL LISTED FOR FIRE PROTECTIVE SERVICE
NOTES
1. Use only listed solenoids from the following table:
Application
NFPA 13
_ Power supply
common connection
Connect to:
SMB-1/2 TB5 Terminal 9
7-12
CZM-1B6 Connections and Ratings

Electrical ratings:
Initiating Devices
Supervisory
18-24.5 VDC
4mA max
Alarm
18-24.5 VDC
45mA max
Zone Resistance
35 ohms total
Max Ripple
500mV
The CZM-1B6 supports one zone of

initiating devices in either Class A (Style
D) or Class B (Style B). The initiating
devices are connected to terminals 5-8 on
the CZM-1B6 terminal block.
Electrical connections:
There are three basic connections to the
CZM-1B6 as follows:

Table 1 - Conventional Detectors:
Compatible With CZM-1B6 on page A-1
may be used. Use up to 15 detectors, any
combination of those listed. Only one
PB-1191, and no additional devices, can
be connected to a CZM-1B6. Detector
operated accessories cannot be used with
the CZM-1B6. The model numbers listed
are the UL compatibility identifiers.
STYLE B
(CLASS B)
EOL
STYLE D
(CLASS A)
+
POWER
POWER
+
ANALOG LOOP
EARTH
EARTH
ANALOG LOOP
EOL
CZM-1B6 Class A (Style D) Wiring
CZM-1B6 Class B (Style B) Wiring
NOTES
1. Power limited to
18 AWG.
35 ohms total.
4. Each detector or group
of detectors, requires
a two-wire circuit of
thermoplastic fixture
wire enclosed in
conduit or limited
energy shielded cable
without conduit, if
permitted by local
building codes.
4.7K, W,
P/N 140-820188.
wired Class A (Style D)
or Class B (Style B)
7. 15 devices maximum
per circuit.
8. Initiating circuit is
supervised.
7-13

PB-1191
When the PBA-1191 is used, the
2-position plug from jumper J1
must be removed as follows:
Remove the screw from the center
of the CZM-1B6 plastic cover and
place it to one side.
Remove the circuit board and
locate jumper J1.
Remove the 2-position plug from J1.
Reassemble the circuit board and plastic
cover using the screw that was removed
in the first step.
Be sure to use the correct end of line
device with the CZM-1B6 in this configuration.
NOTES
1. Power limited to
18 AWG.
100 ohms total.
4. Maximum capacitance:
0.4F between + loop
and loop.
0.8F between + loop
and chassis.
0.8F between loop
and chassis.
of detectors, requires a
two-wire circuit of
wire enclosed in conduit
or limited energy
shielded cable without
conduit, if permitted by
local building codes.
required.
7. Operates in full
conformance with
Style 6.
8. Operates in full
conformance with
Style 4.
9. Either loop may be wired
Class A or B.
10. 60 devices maximum per
loop.
allowed on Class A
loops.
supervised.
7-14
PB-1191 Installation
Analog Loops
The CZM-1B6 communicates with the
MXL-IQ via the MXL-IQs analog loops,
which may be on the SMB-2 or the optional
ALD-2I module. The analog loops may be

wired Class A (Style 6) or Class B (Style 4).
ALD-2I
MOM-4
TB2
MOM-4
TB1
SMB-2
SMB-2
LOOP LOOP LOOP LOOP LOOP

1
2
1
2
1
LOOP
2
TB2
TB3
CLASS A INSTALLATION
See notes 7 and 11.
CZM-1B6
+
+
CZM-1B6
1
7
CLASS B INSTALLATION
See note 8.
CZM-1B6
1
2
CZM-1B6
1
7
CZM-1B6
1
8
CZM-1B6
1 2
Analog Loop Wiring
CZM-1B6
1
7
CZM-1B6 Power
The CZM-1B6 receives its power from the
CZM-1B6 power output on the SMB-2. This
power is available on TB5 of the SMB-2 on
terminals 9-12. The power may be wired as
SMB-2
TB5
12
11
10
Class A or Class B. Since the CZM-1B6

monitors the power at its screw terminals, it
is possible to T-tap the power connection; this
can be done only in the Class B configuration.
CLASS A INSTALLATION
+
+
See note 6.
CZM-1B6
5
CZM-1B6
5
CZM-1B6
1 2
12
11
10
9
CLASS B INSTALLATION
+
-
4
1
CZM-1B6
5
4
1 2
CZM-1B6
5
CZM-1B6
+
4
CZM-1B6
CZM-1B6
5
NOTES
1. Power limited to
18 AWG.
4 ohms total.
required.
5. Circuit is supervised.
6. T-tapping is NOT
allowed on Class A
loops.
7. For loop resistance,
refer to the SMB-2
Installation Instructions,
P/N 315-095097.
CZM-1B6 Power Wiring
7-15
NOTES
1. Intrinsically Safe Output:
Open Circuit Voltage: 28 VDC
Short Circuit Current: 93mA
2. Maximum loop resistance must not exceed 35 ohms.
3. A maximum of ten DI-3IS Ionization Detectors or up to
five S121 or S122 Flame Detectors can be used in
addition to mechanical (non-energy storing) shorting
devices.
4. Maximum safe system voltage is 250 VAC.
5. For mounting and installation of the ISI-1, see the ISI-1
instructions.
6. Only mechanical (non-energy storing) shorting devices
Intrinsically Safe Zone Wiring

FM Approved Only (Not UL Approved)
7-16
such as the MS-51 Manual Station may be used.

7. WARNING: Do not make any connection to terminal 6 of
the DB-3S base. Such a connection would void use in an
intrinsically safe application.
8. In addition, S121 and S122 are also approved for use in
Class II and Class III, Groups E, F, and G.
9. For guidance on installation see ANSI/ISA RP 12.6,
Installation of Intrinsically Safe Instrument Systems in
Class I Hazardous Locations.
10. For DI-3IS information, see the DI-3 Series installation
instructions, P/N 315-081943.
11. For S121 and S122 information, see the installation
instructions, P/N 315-085258.
CZM-4 Connections and Ratings

Electrical ratings:
Initiating devices per zone:
Supervisory
21.7-22.8 VDC
4mA max
Alarm
21.7-22.8 VDC
180mA per zone max
Max ripple
400mV
Up to 30 detectors, any combination of

those listed in Appendix A, Table 1 Conventional Detectors (except the
PBA-1191), on page A-1, may be used.
Up to five waterflow switches or 20
tamper switches may be used. Wiring
may be Style D (Class A) or Style B
(Class B).
STYLE B
(CLASS B)
STYLE D
(CLASS A)
STYLE B
(CLASS B)
ZONE 1
ZONE 2
ZONE 3
ZONE 4
10
11
12
13
14
15
16
50uF
50V *
MOM-4 TERMINALS
TB1 (UPPER SLOT) OR
TB2 (LOWER SLOT) OR
MOM-2 TERMINAL TB2
50uF 50V *
PBA-1191
Linear Beam Detector
- + - + - +
+
50uF, 50V *
DO NOT
USE
* EOL CAPACITOR (P/N 100-115588)

** EOL RESISTOR (P/N 140-820188)
CZM-4 Wiring
EOL
4.7K, 1/4W **
NOTES
1. Power limited to
18 AWG.
70 ohms total
(40 ohms if relay bases
are used).
of detectors, requires a
two-wire circuit of
wire enclosed in
conduit or limited
energy shielded cable
without conduit, if
permitted by local
building codes.
5. Loops may be wired
Class A (Style D) or
Class B (Style B).
per loop.
7. All circuits are
supervised.
8. Do not connect more
than one PBA-1191 to
each zone. (Refer to
PBA-1191 instruction,
P/N 315-095424 for
further information.)
9. Do not mix smoke
detectors with the
PBA-1191.
10. The PBA-1191 requires
Rev. 3 or higher of
CZM-4 firmware.
7-17
CZM-4 Connections and Ratings
7-18
MOI-7, MOD-16, MID-16

MOI-7
Electrical ratings:
Supervisory
5V .5V
140mA
Alarm
5V .5V
180mA
Electrical connections
The MOI-7 is shipped with one cable as
described below.
5V Power
The MOI-7 receives its 5 volt power on
connector P1. This power can be sent to other
modules requiring 5 volts from P2. Pin 1 is the
positive input; pin 2 the return. Use the
supplied cable, P/N 600-291261.
24V Return
TB2 connects to the return side of the
power supply used with the MOD-16s and
MID-16s. There are two positions on the
TB2position 1 connects to the MOD-16/
MID-16 and position 2 to SMB-2, TB5-9, or
to PS-35, terminal 6.
MOD-16 and MID-16 Connection
P4 is the connector for the MOD-16/MID-16
modules. Connect the first MOD-16/MID-16
in the system using a 10-wire cable
P/N 555-190940. Be sure that the locking
tab on the cable engages the rib on P4.
MXL-IQ Network Connection

For Style 4 wiring use only terminals 1 and
2 of TB1; terminals 3 and 4 of TB1 are not
used. In a Style 4 network, make only
Network A connections and ignore all
Network B connections. Do not use
connector P5 in this configuration.
7-19
MOI-7, MOD-16, MID-16 Connections and Ratings
NETWORK A
TB4
4
N
E 3
T
W
O 2
R
K 1
RCC-1/1F
(PS-5N7)
CABLE P/N 600-291261

TO PSR-1, P9 OR PS-5, J2
D D
O O
U
S
E
NOTES:
1. 18 AWG minimum.
2. 80 ohms maximum per
pair.
3. Use twisted pair or
shielded twisted pair.
4. Terminate the shield at
the SMB-2 enclosure
only.
5. Power limited to NFPA
70 per NEC 760.
6. Maximum voltage 8V p-p.
7. Maximum current
150mA.
STYLE 4
N N
O O
T T
+5 VDC IN
P1 P2
SEE
MOI-7
WIRING
U
S
E
4 3 2 1
TB1
TB2
DO NOT USE
P5
MOI-7
MXL-IQ Network Connection Wiring Diagram

Local Trouble Input
When terminal 3 of TB3, the local trouble
input, is driven high, it reports a trouble
condition to the MXL-IQ. This input is
protected and has a maximum input rating
of 40V. Terminal 2 of TB3 is the common
for this input.
Local Lamp Test
Terminal 1 of TB3 is used for a local lamp
test. When this input is pulled low, the
MOD-16 outputs do a lamp test. Use a
normally open momentary switch connected between terminal 1 and 2 of TB3.
7-20
Inputs
The MOI-7 has two inputs. The first input
allows for a local lamp test of all connected
MOD-16 outputs. Screw terminal 1 on TB3
is the lamp test input. To activate the lamp
test, use a normally open switch between
terminals 1 and 2 (common) of TB3.
Each MOD-16 board is lamp tested sequentially. The lamp test sequence stops
automatically after approximately 30
seconds. The second input is for transmission to the MXL-IQ of local trouble. This
input is high going for trouble. Each MOI-7
transmits the state of this input to the
MXL-IQ for annunciation. The MXL-IQ
indicates this trouble as an MOI-7 local
trouble. See the electrical ratings and wiring
diagrams for these two inputs.
MOD-16
MID-16
Electrical ratings:
Electrical ratings:
Supervisory
40V peak
2mA
Alarm
40V peak
850mA
Maximum current
for each output
50mA
Module power
5VDC
2mA max
Input ratings:
Input voltage range
18-31 VDC
Input impedance
8K ohms
Input current
2mA max
MOI-7 Wiring
7-21
NOTES
1. 18 AWG minimum for
LED and 24V lamp
connections.
supply connections
(TB1-9 and 10, TB2-9
and 10).
3. All wiring must be in
accordance with NEC
760.
4. All wiring must
having jurisdiction over
the installation.
5. All wiring to MID-16,
MOD-16, or MOI-7
(non-network) modules
is unsupervised. Any
wiring leaving the
enclosure must be
within 20 feet, in rigid
conduit, and must not
leave the room.
6. For additional
information see
MOI-7 Installation
Instructions,
P/N 315-092799.
7. A maximum of 8
MOD-16s can be used
with the MOI-7.
8. Both TB1-9 (or 10) and
TB2-9 (or 10) must be
connected to the
common of the power
supply.
9. When using SR-35,
refer to table on this
page.
TO COMMON OF SUPPLY OR TB1-10

OF PREVIOUS MOD-16 OR MID-16
TO TB1-9 OF NEXT
MOD-16 OR MID-16
SEE NOTE 8
TB1, 1-8, PROVIDES

CONTROLLED OUTPUTS
TB1
1
S1, 1-8 CONNECT TO

CORRESPONDING
OUTPUTS TB1, 1-8
SW1
1 2 3 4 5 6 7 8
P1
P2
MOD-16
FROM PREVIOUS
MOD-16, MID-16
OR MOI-7 (CABLE
P/N 555-190940)
NOTE: THE CABLE P/N 555-190940 IS

SUPPLIED. IF THE CONNECTION
IS TO ANOTHER RAIL IN THE
ENCLOSURE, USE OPTIONAL
CABLE P/N 555-190941.
TO NEXT
MOD-16 OR MID-16
(CABLE P/N 555-190940)
NOTE:
SWITCH S2-8 IS OPEN TO
PROVIDE A 2.7K LIMITING
RESISTOR.
S2, 1-8 CONNECT TO

CORRESPONDING
OUTPUTS TB2, 1-8
TB2, 1-8 PROVIDES ADDITIONAL

CONTROLLED OUTPUTS
10
SW2
1 2 3 4 5 6 7 8
CONNECT TO ONE OF THE FOLLOWING:
TB2
1
10
LED
MODULE
TERMINAL
SMB-2
MPS-24
PS-35
TB5-12
TB1-4
TB1-5
OR ANY AUXILIARY POWER SUPPLY

U.L. LISTED FOR FIRE PROTECTION
SIGNALING USE

TO TB2-9 OF NEXT
MOD-16 OR MID-16
MOD-16 Wiring
Connection To SR-35 Module*
MOD-16
SR-35 Screw Terminal
TB1-1
TB1-2
TB1-8
32
SMB-2, TB5-12 or
PS-35, TB1-5
33
SMB-2, TB5-9 or
PS-35, TB1-6
35
*For additional information see:

SR-35 Instructions (P/N 315-087691)
PS-35 Instructions (P/N 315-085062)
SMB-2 Instructions (P/N 315-095931)
7-22

TB1, 1-8, PROVIDES

THE FIRST 8 INPUTS
TO TB1-9 OF NEXT
MOD-16 OR MID-16
TB1
1
10
10
P1
DO NOT USE
P3
P4
P5
NOTE: THE CABLE P/N 555-190940 IS

SUPPLIED. IF THE CONNECTION
IS TO ANOTHER RAIL IN THE
ENCLOSURE, USE OPTIONAL
CABLE P/N 555-190941.
MID-16
FROM PREVIOUS
MOD-16, MID-16
OR MOI-7 (CABLE
P/N 555-190940)
10
TO NEXT
MOD-16 OR MID-16
(CABLE P/N 555-190940)
10
SWITCH
1
TB2, 1-8 PROVIDES

THE SECOND
8 INPUTS
NOTES
all input connections.
10
P2
CONNECT TO ONE OF THE FOLLOWING:
TB2
1
INPUT IMPEDANCE: 8K OHMS

MAXIMUM INPUT CURRENT:
4mA / INPUT
10
MODULE
TERMINAL
SMB-2
MPS-24
PS-35
TB5-12
TB1-4
TB1-5
OR ANY AUXILIARY POWER SUPPLY

U.L. LISTED FOR FIRE PROTECTION
SIGNALING USE

TO TB2-9 OF NEXT
MOD-16 OR MID-16

supply connections
(TB1-9 and 10, TB2-9
and 10).
3. All wiring must be
in accordance with
NEC 760.
4. All wiring must
conform to local
codes and to the
authority having
jurisdiction over the
installation.
5. All wiring to MID-16,
MOD-16, or MOI-7
(non-network)
modules is
unsupervised. Any
wiring leaving the
enclosure must be
within 20 feet, in rigid
conduit, and must not
leave the room.
6. For additional
information see
MOI-7 Installation
Instructions,
P/N 315-092799
7. A maximum of 8
MID-16s can be used
with the MOI-7.
8. P1 is connected in
parallel with TB1.
9. P2 is connected in
parallel with TB2.
MID-16 Wiring
7-23
7-24
MOM-2 Connections and Ratings

Electrical Installation
There are two inputs that connect the
MOM-2 with the SMB-2. These inputs
provide all the necessary power and data
lines to support the optional modules.
The first input is an 8-conductor ribbon
cable. Attach the cable to P6 on the
SMB-2, making sure that the locking rib on
the cable connector engages the locking
tab on P6. Attach the other end of the
cable to P7/P10 on the MOM-2, again
making sure that the locking rib on the
cable engages the locking tab on P7/P10.
This cable supplies 5 VDC and communication between the SMB-2 and the modules installed in the MOM-2.
The second input feeds 24 VDC full wave
unfiltered DC to the MOM-2. This input is
connected to either P5/P8 (SMB-1 only) or
TB6/TB7. A 2-wire cable is provided for
backward compatibility with the SMB-1.
Connect one end of the cable to P3 on the
SMB-1, making sure the cable rib and board
tab lock. Attach the other end of the cable
to P5/P8 on the MOM-2 in the same way.
The SMB-1 limits this power input to 2
amps. Under maximum load conditions the
optional modules must never draw more
than 2 amps from this connection.
When the 24 VDC is provided by the
SMB-2 use TB6/TB7 on the MOM-2 to
connect the power. The wire for this
connection is not supplied (See SMB-2
Installation Instructions, P/N 315-095931
for terminal connections). Use the following chart to determine the available 24
VDC current.
Depending on the optional modules

installed, additional power may be available at TB5 and for notification appliances.
See the table in Appendix D - MXL
Power Supply Load Calculations on
page D-2 for the maximum current required by each module under full load
conditions.
Depending on the optional modules used,
determine the outstanding power by using
the table in Appendix D - MXL-IQ Power
Supply Load Calculations on page D-2
(See the EXAMPLE). This power can be
used for notification appliances or for the
optional power connector on TB5.
NOTE: When a CSM-4 is used, you may
add notification appliances to it if the
maximum load current to the MOM-2 does
not exceed 2 amps (SMB-1); or with an
SMB-2, 6 amps (MPS-6/6W) or 12 amps
(MPS-12/12W). Include the total alarm
current on each CSM-4 notification appliance
circuit when performing the calculations.

Source
Max. Current
SMB-2 wit h MPS -6/6W
6*
12 *
* Derat e by t he t ot al of CZM-1B6 power, NAC-1 and NAC-2
7-25
EXAMPLE:
With:
one CZM-4 and

one CRM-4 and
one CSM-4
Total load current =

0.720 + 0.075 + 0.034 = 0.83A
With MPS-6/6W:
Remaining Available Current =
2.0 - 0.83 = 1.17A (SMB-1)
6.0 - 0.83 = 5.17A (SMB-2) with no
CZM-1B6 load
With MPS-12/12W:
2.0 - 0.83 = 1.17 (SMB-1)
12.0 - 0.83 = 11.17 (SMB-2) with no
CZM-1B6 load
7-26

Electrical Installation
There are two inputs that connect the
MOM-4 with the SMB-1/-2. These inputs
provide all the necessary power and data
lines to support the optional modules.
The first input is an 8-conductor ribbon
cable. Attach the cable to P6 on the
SMB-1/-2 making sure that the locking rib
on the cable connector engages the
locking tab on P6. Attach the other end of
the cable to P7/P10 on the MOM-4, again
making sure that the locking rib on the
cable engages the locking tab on P7/P10.
This cable supplies 5 VDC and communication between the SMB-2 and the modules installed in the MOM-4.
The second input feeds 24 VDC full wave
unfiltered DC to the MOM-4. This input is
connected to either P5/P8 (SMB-1 only) or
TB6/TB7. A 2-wire cable is provided for
backward compatibility with the SMB-1.
Connect one end of the cable to P3 on the
SMB-1, making sure the cable rib and
board tab lock. Attach the other end of the
cable to P5/P8 on the MOM-4 in the same
way. The SMB-1 limits this power input to 2
amps. Under maximum load conditions the
optional modules must never draw more
than 2 amps from this connection.
When the 24 VDC is provided by the
SMB-2 use TB6/TB7 on the MOM-4 to
connect the power. The wire for this
connection is not supplied (See SMB-2
Installation Instructions, P/N 315-095931
for terminal connections). Use the following chart to determine the available 24
VDC current.
Depending on the optional modules

installed, additional power may be available at TB5 and for notification appliances.
See the table in Appendix D - MXL
Power Supply Load Calculations on
page D-2 for the maximum current required by each module under full load
conditions.
Depending on the optional modules used,
determine the outstanding power by using
the table in Appendix D - MXL Power
Supply Load Calculations on page D-2.
(See the EXAMPLE). This power can be
used for notification appliances or for the
optional power connector on TB5.
NOTE: When a CSM-4 is used, you may

add notification appliances to it if the
maximum load current to the MOM-4 does
not exceed 2 amps (SMB-1); or with an
SMB-2, 6 amps (MPS-6/6W) or 12 amps
(MPS-12/12W). Include the total alarm
current on each CSM-4 notification appliance
circuit when performing the calculations.

Source
Max. Current
6*
12 *
* Derat e by t he t ot al of CZM-1B6 power, NAC-1 and NAC-2
7-27
EXAMPLE:
With:
one CZM-4 and

one CRM-4 and
one CSM-4
Total load current =

0.720 + 0.075 + 0.034 = 0.83A
With MPS-6/6W:
2.0 - 0.83 = 1.17A (SMB-1)
6.0 - 0.83 = 5.17A (SMB-2) with no
CZM-1B6 load
With MPS-12/12W:
2.0 - 0.83 = 1.17 (SMB-1)
12.0 - 0.83 = 11.17 (SMB-2) with no
CZM-1B6 load
7-28
NIM-1R Connections and Ratings

Electrical ratings:
The network can be installed as either Style

4 or Style 7. Style 7 is required in Canada.
5 VDC, 160mA
For battery calculations, the
NIM-1R draws 70mA from 24 VDC.
NIM-1R Network
Up to 32 MXL-IQ Systems can be connected in the network with an NIM-1R
installed in each MXL-IQ System. For the
highest level of fault protection, install the
NIM-1R in the enclosure with the SMB-2,
although this is not necessary. When
connecting more than 32 MXL-IQ Systems,
a REP-1/D2300CP repeater is required.
Refer to the REP-1 Installation Instructions,
P/N 315-092686 or the D2300CP Installation Instructions, P/N 315-092882, for the
wiring diagram.
Each NIM-1R is shipped with two 120 ohm

EOLRsonly two are required for each
network pair. Install an EOLR at the ends of
each network pair. Do not install an EOLR at
each NIM-1R. (For a simple rule of thumb,
an EOLR must be installed where only a
single wire lands on a screw terminal.)
NOTES
1. Power limited to
18 AWG.
80 ohms per pair.
5. Terminate the shield
ONLY at MXL-IQ
panel 1.
6. Maximum voltage:
8V P-P.
7. Maximum current:
150mA.
8. For Style 4 omit all
Network Pair B
connections.
9. Do not use terminals
12 - 16 if NCC is not
connected.
Do not T-tap the network wiring. If T-tapping

is required, use the REP-1/D2300CP
repeater. Refer to the REP-1 Installation
Instructions, P/N 315-092686 or the
D2300CP Installation Instructions, P/N 315092882, for the wiring diagram. For Style 4
wiring, terminate the secondary network
pair (terminals 3 and 4) on each NIM-1R
with an EOLR.
NETWORK PAIR B *
SUPERVISED (OMIT FOR STYLE 4)
EOLR
120 OHMS, 1/4W
P/N 140-820150
CABLE P/N
555-190506
TO SMB-2
DO NOT USE
TB1, 1-16
DO NOT
USE
P7
CABLE P/N
555-190506
TO SMB-2
SEE
FIGURE 2
10
11
12
13
14
15
16
TB3
NIM-1R
MOM-2/-4
EOLR
120 OHMS, 1/4W
P/N 140-820150
NETWORK PAIR A
SUPERVISED
EOLR
120 OHMS, 1/4W
P/N 140-820150
DO NOT USE
TB1, 1-16
DO NOT
USE
P7
CABLE P/N
555-190506
TO SMB-2
SEE
FIGURE 2
10
11
12
13
14
15
16
TB3
NIM-1R
P3
INSTALLED IN MXL-IQ PANEL 1
MOM-2/-4
EOLR
120 OHMS, 1/4W
P/N 140-820150
DO NOT USE
TB1, 1-16
DO NOT
USE
P7
SEE
FIGURE 2
10
11
12
13
14
15
16
TB3
NIM-1R
P3
MOM-2/-4
P3
* REQUIRED IN CANADIAN INSTALLATIONS
NIM-1R Network Wiring (Figure 1)
7-29
Network Command Center (NCC)
The total number of panels in the network must not exceed 64, including the
NCC.
The RS-232 interface connects to the NCC

with a 9-pin female D-SUB connector.
For NIM-1Rs that are not connected to

an NCC, leave terminals 1216 disconnected.
Observe the following restrictions:

Give the NCC a panel number. (This
panel number is in addition to the panel
number for the MXL-IQ system that the
NCC connects to.)
5
DO NOT USE
9
4
DO NOT USE
CONNECT TO COM1
OF NCC/NCC-G
CABLE P/N 555-193085
3
7
2
6
DO NOT USE
1
DO NOT USE
SEE
FIGURE 1
DO NOT USE
1
10
11
12
13
14
15
16
TB1
DO NOT USE
5
10
11
12
13
14
15
16
TB3
NIM-1R
P1
P3
MOM-4
P2
P4
TB2
1
TB4
2
10
11
12
13
14
15
16
NIM-1R and NCC Wiring (Figure 2)
7-30
P7
BLACK
SUPERVISED
CABLE P/N 555-190506 TO SMB-2
GREEN
NOTES
1. Power limited to
18 AWG.
3. Maximum cable length
25 feet.
4. Cable must be in rigid
conduit and can not
leave the room.
5. Shielded cable is not
recommended.
6. Maximum voltage:
24V peak to peak.
7. Maximum current:
20mA per circuit.
WHITE
RED
BROWN
DB9 FEMALE
10
11
12
13
14
15
16
DO NOT USE
TERMINALS 12-16
IF NCC IS NOT
CONNECTED
Foreign System Interface (FSI)
For networked systems, each FSI port

must be configured as either local or
global in the CSG-M. Local FSI ports
display information only on the MXL-IQ
System to which they are connected.
Global FSI ports display all events in all
MXL-IQ Systems. Refer to the CSG-M
Manual, P/N 315-090381, for further
information.
The FSI installs on TB3 or TB4, terminals

1 and 2, of the MOM-4/-2 depending on
where the NIM-1R is installed. Use one of
the EOLRs provided with the NIM-1R on
terminals 1 and 2. This properly terminates
the FSI. Use the second EOLR on terminals 3 and 4. Never use terminals 3 and
4 to connect to the FSI. Refer to Figure 3
for the polarity of the FSI driver.
If multiple FSI connections are required,
up to four NIM-1Rs may be installed in an
individual MXL-IQ System. In networked
systems each MXL-IQ can support up to
four FSI ports.
CONNECT ONLY TO
UL EDP OR ETI LISTED
EQUIPMENT
EOLR
120 OHMS, 1/4W
P/N 140-820150
SUPERVISED
TRANSMIT
EOLR
120 OHMS, 1/4W
P/N 140-820150
TRANSMIT ENABLE
RECEIVE
EOLR
120 OHMS, 1/4W
P/N 140-820150
CABLE P/N 555-190506 TO SMB-2

DO NOT USE
1
10
11
FOREIGN SYSTEM RS-485 INTERFACE
DO NOT USE
12
13
14
15
16
P7
TB1
10
11
12
13
14
15
16
TB3
NIM-1R
P1
P3
MOM-4
P2
P4
TB2
1
TB4
2
10
11
12
13
14
15
16
NIM-1R and FSI Wiring (Figure 3)
10
11
12
13
14
15
16
NOTES
1. Power limited to
18 AWG.
80 ohms per pair.
ONLY at NIM-1R
enclosure.
6. Maximum voltage:
8V P-P.
7. Maximum current:
150mA.
7-31
AnaLASER Interface
Complete wiring of the converter before

installing the ACC-1 in the enclosure.
The AnaLASER interface connects to the

MOM-4/-2, TB3 or TB4, terminals 1 and 2,
depending on where the NIM-1R is
installed. Up to 31 AnaLASER detectors
can be connected to a single NIM-1R.
Place the end-of-line resistors in the

locations specified in Figure 4 below.
Install the cable, P/N 500-693801
between the converter and the ACC-1.
The ACC-1 requires an RS-485 to RS-232

converter which mounts in the back of the
ACC-1 enclosure. The converter model
number is AIC-4Z. The AIC-4Z supports
from one to four AnaLASER detectors.
Refer to the AIC-4Z Installation Instructions, P/N 315-093792, for the mounting
and configuration of the converter and the
ACC-1s.
Refer to the AnaLASER Air Sampling

Smoke Detection Manual, P/N 315092893, for connection to the AnaLASER
detector and power supply, as well as
mechanical mounting of the ACC-1.
NOTES
1. Power limited to
18 AWG.
80 ohms per pair.
ONLY at NIM-1R
enclosure.
6. Maximum voltage:
8V P-P.
7. Maximum current:
150mA.
EOLR
120 OHMS, 1/4W
P/N 140-820150
EOLR
120 OHMS, 1/4W,
P/N 140-820150
SUPERVISED
EOLR
120 OHMS, 1/4W
P/N 140-820150
CABLE P/N
555-190506
TO SMB-2
TO POWER SUPPLY, TB2 LOAD -
10
11
12
13
14
15
16
16 15 14 13 12 11 10
TB3
TO ACC, TB2, TERMINAL 10
16 15 14 13 12 11 10
2
1
3
2
1
3
2
1
LK1
LK2
SINGLE
ZONE
LK1 1-2 JUMPERED

LK2 2-3 JUMPERED
LK3 2-3 JUMPERED
CON3
AIC-4Z
JUMPER SETTINGS
CON4
TB1
AIC-4Z
P3
TO POWER SUPPLY, TB2 LOAD +
DO NOT
USE
TB1
NIM-1R
MOM-4
TO POWER SUPPLY, TB2 LOAD +
DO NOT
USE
DO NOT USE
P7
TO POWER SUPPLY, TB2 LOAD -
CON2
CON1
LK3
REFER TO THE ANALASER AIR SAMPLING SMOKE DETECTION

MANUAL, P/N 315-092893, FOR CONNECTION OF THE ACC,
THE POWER SUPPLY, AND THE ANALASER DETECTOR AND
AIR SAMPLING NETWORK.
2
1
LK1
3
2
1
LK2
3
2
1
LK3
TO ACC #1, P4
CABLE P/N 500-693801
JUMPER SETTINGS
MULTI
ZONE
LK1 1-2 JUMPERED

LK2 2-3 JUMPERED
LK3 2-3 JUMPERED
CON4
CON3
CON2
CON1
TO ACC #28, P4
TO ACC #29, P4
TO ACC #30, P4
TO ACC #31, P4
NIM-1R and AnaLASER Wiring (Figure 4)
7-32
Silent Knight Model 5128/5129

Electrical ratings:
Supervisory
18-40 VDC
60mA
Alarm
18-40 VDC
130mA
Electrical connections:
The MXL-IQ Control Panel connects to the
Silent Knight Model 5128/5129 Digital Fire
Communicator using the Alarm, Trouble,
and Supervisory dry contacts on the
MXL-IQ Main Board.
Refer to the Silent Knight 5128/5129 Fire
Slave Communicator Installation Manual,
P/N 150805, provided with Silent Knight
Model 5128/5129 for dialer instructions.
In NFPA 72 Central Station connections,

AC fail reporting is delayed. The delay is 6
hours (25% of 24 hours) for NFPA Local
and Proprietary, and 15 hours (25% of 60
hours) for NFPA Municipal Tie and Remote
Station. Only the reporting of the trouble is
delayed.
AC power must be present for a full minute
before the system switches back to AC
power from the battery.
Using the optional AC monitor input, the
Silent Knight Model 5128/5129 monitors AC
fail trouble. When the MXL-IQ System
reports an AC fail trouble, the Silent Knight
Model 5128/5129 sends a specific code to
the Central Station that identifies the trouble
as AC fail.
The Silent Knight Model 5128/5129

monitors all System troubles through the
MXL-IQ trouble relay. The MXL-IQ delays
the AC fail trouble signal in accordance
with NFPA and UL requirements.
In NFPA 72 Remote Station, install batteries to provide 60 hour standby capacity.
For signalling service DACT wire according to the diagram on the following page.
7-33
12
CZM-1B6
POWER
11
10
9
8
7
CHASSIS
6
5
NOT SUPERVISED
SMB-2
3
2
(RED)
(BLK)
(YLW)
(ORN)
(RED)
TROUBLE
5
4
2
1
SILENT KNIGHT 5230

(PROGRAMMING)
TELCO 1 TIP (RED)
HOUSE 1 TIP (GRAY)
(GRY)
(VIO)
HOUSE 1 RING (BROWN)
TO RJ31X
(BLU)
TB4
(GRN)
NOT USED
P2 - CHANNEL INPUTS
NOT USED
(RED)
* UL LISTED
EOL DEVICE
4.7K, 1/2W, 5%
(P/N 140-820388)
NOTES
1. TRI-60R/B6R input
must be programmed
in CSG-M as trouble
causing.
2. TRI-60R/B6R output
must be programmed
in CSG-M to transfer
on loss of AC Mains.
3. All wiring supervised
except as noted.
4. For Remote Station,
provide 60 hour
battery capacity.
TELCO 1 RING (GREEN)
SUPERVISED
P4
(BRN)
ALARM
P1 - DC POWER
HOUSE 2 TIP (GRAY)
SUPERVISED
(BRN)
(WHT)
(BLK)
UL LISTED
EOL DEVICE
3.6K, 1/4W
(P/N 140-820185)
6 5
HOUSE 2 RING (BROWN)
4 3
TRI-B6R
MXL-IQ to Silent Knight Model 5128/5129 Wiring Diagram
P3 - AC MONITOR
(SEE NOTE 2)
RELAY NC
RELAY C
RELAY NO
SILENT KNIGHT
MODEL NO. 5128/29
TELCO 2 TIP (RED)
TELCO 2 RING (GREEN)
TO RJ31X
Silent Knight Model 5128/5129 Connections and Ratings
7-34
TB5
SMB-2 Connections and Ratings

INTERNAL WIRING
To complete the SMB-2 internal wiring

connections, follow the steps below, skipping
those that do not apply to your particular
MXL-IQ System.
Main power connections

Primary power for the SMB-2 is provided by
the MPS-6/6W or MPS-12/12W. Both of
these mount in the lower right-hand corner
of the MXL-IQ enclosure. Follow the instructions below for the appropriate power supply.
MPS-6/6W- Install the MPS-6/6W (See

MPS-6/6W Instructions, P/N 315-090334/W).
With the AC mains disconnected, connect
the MPS-6/6W power cable to P1 of the
SMB-2. Be sure that the jumper assembly is installed in P14 of the SMB-2. If
this jumper is not installed, the SMB-2
will detect a permanent AC fail or
indicate auxiliary power voltage is low.
MPS-12/12W - Install the MPS-12/12W
(See MPS-12/12W Instructions, P/N 315092030/W). Remove and discard the jumper
assembly installed in P14 of the SMB-2.
Disconnect the AC mains. Connect the
MPS-12/12W power cable to P14 of SMB-2.
Battery power connection

The SMB-2 kit includes a battery cable
(wiring harness). Use the harness to
connect the 24V backup batteries to P2 of
SMB-2.
MOM-4 optional module card cage

There are two connections between the
SMB-2 and the MOM-4 board.
1. 24V power connection.
P3 provides backward compatibility with the
SMB-1 and should only be used when
replacing an SMB-1. P3 is limited to 2
amps. The SMB-2 allows the use of either
an MPS-6/6W or an MPS-12/12W. TB1
terminals 4 and 5 supply 24V to the MOM-4
with a maximum of 6 amps (MPS-6/6W) or
12 amps (MPS-12/12W) available. This
output must be derated by the total current
drawn from NAC1 (1.5A max), NAC2 (1.5A
max) and the CZM-1B6 power (1A max) on
the SMB-2. Connect TB1, 4 and 5 on the
SMB-2 to TB6/TB7, 1 and 2 on the MOM 4.
2. 5V power and the communication
interface. Connect the 8-wire ribbon cable
from P7/P10 on the MOM-4 to P6 on the
SMB-2.
7-35
FIELD WIRING
The screw terminals for the field wiring
circuits are located on the left and right
sides of the SMB-2. They are labeled
TB1 through TB5.
SMB-2
The field wiring circuits available are:

CZM-1B6 power
Analog device loop 1
Analog device loop 2
Notification appliance circuit 1
Notification appliance circuit 2
Common alarm relay
Common trouble relay
Style 4 RS-485 Network (MNET)
The following sections describe each
circuit type and give the related instructions. Refer also to the wiring diagrams.
MOM-4 24V Wiring
CZM-1B6 power
CZM-1B6
12
11
DO NOT
USE
10
DO NOT
USE
CZM-1B6
T-TAPPING
ALLOWED
9
TB5
CZM-1B6
CZM-1B6 Supervised Auxiliary Power

Class B Wiring
7-36
Auxiliary power is available on TB5,

terminals 9 through 12 of the SMB-2.
The circuit is power limited per NEC
Article 760 and is rated at 1 amp, 18-31
VDC.
This power supply is for use with the
CZM-1B6 Remote Conventional Zone
module.
You may connect a maximum of 20
CZM-1B6s to this power source.
T-tapped wiring can be used to obtain
the maximum of 20 CZM-1B6s. Each tap
can support a maximum of 10 CZM1B6s, 4 ohms max. Multiple power
connections can be used provided you
do not exceed the ratings above (20
CZM-1B6s max and 4 ohms per run
max). For example, you could have four
individual T-tapped power runs, for a
total of 20 devices (6, 4, 3, and 7 CZM1B6s), each of the four runs not
exceeding 4 ohms resistance.
Analog device loops 1 and 2

(TB2 and TB3)
To install a device for Class B, refer to the
wiring diagram below and the electrical
ratings.
Wiring the Analog Loops

Class B Wiring
To install a device for Class A, refer to the
wiring diagram below and the electrical
ratings.
Wiring the Analog Loops

Class A Wiring

Table 2 - Analog Addressable Detectors
on page A-1 may be used. The UL identifiers for compatibility are the same as the
model names specified.
NOTES
1. Power limited to
of detectors requires
the following:
a 2-wire circuit of 18
AWG minimum
wire enclosed in a
conduit.
or
18 AWG limitedenergy shielded cable
without conduit, if
permitted by local
building codes.
100 ohms total.
4. Maximum
capacitance:
0.4F between + loop
and loop.
0.8F between + loop
and chassis.
0.8F between loop
and chassis.
5. Refer to Wiring Guide
for compatible wire
types.
6. Maximum voltage:
Supervisory 30 VDC
peak.
Alarm 30 VDC peak.
7. Maximum current:
Supervisory 66mA
Alarm 66mA
required.
9. Operates in full conformance with Style 4.
10. Operates in full conformance with Style 6.
11. Either loop may be
wired Class A or B.
per loop.
allowed on Class A
loops.
supervised.
Analog loop electrical ratings:

Supervisory
30 VDC peak
66mA max
Alarm
30 VDC peak
66mA max
(60 devices in alarm)

codes.
7-37
Notification appliance circuits

(TB5, 1-4 and TB5, 5-8)
These circuits are for notification appliances only, NFPA 72 Local. For NFPA 72
Municipal Tie or NFPA 72 Leased Line,
use the Model CSM-4.
Article 760 of NEC and local building
codes.
Common Alarm Relay

The common alarm relay changes state
whenever a fire alarm is detected.
Common Trouble Relay

The trouble relay changes state whenever
a System trouble is detected.
NOTES
1. Contact rating: 2A,
30 VDC/120 VAC
resistive.
2. Use only with power
limited / Class 2
circuits.
3. Coils are supervised
when de-energized.
4. Contacts are not
supervised.
5. All relay contacts are
shown in normal state.
NOTES
1. Power limited to
18 AWG.
3 ohms total.
2.2K, W,
P/N 140-820380.
wired Class A or B.
supervised.
supervisory state.
TROUBLE
Notification Appliance Circuits Wiring
ALARM
SMB-2 Relay Wiring

Electrical ratings:
Supervisory
Alarm
24V, unfiltered
full wave rectified
12mA max
24V, unfiltered
full wave rectified
1.5A max
Only the devices listed in Compatible

Notification Appliances, P/N 315-096363
may be used. The UL identifiers for
compatibility are the same as the model
names specified.
7-38
Style 4 Network (MNET)

The SMB-2 provides a Style 4 MNET
network for connection to remote annunciators (MOI-1/7, RCC-1/1F).
NOTES
1. Power limited to
18 AWG.
80 ohms total.
ONLY at the SMB-2
chassis.
6. Maximum voltage:
8V P-P.
7. Maximum current:
150mA.
SMB-2
Style 4 Network (MNET) Wiring
SMB-2 Fuses
NOTE: The fuses are located on the upper left and right
corners of the SMB-2 board.
FUSE RATINGS
F1
MPS-6 Input
8A, 3 AG,
Normal Blow
F2
Battery
Reversal
20A, 3 AG,
Normal Blow
F3
CZM-1B6
Power
2A, 3 AG,
Normal Blow
F4
24V Output
15A, 3 AG,
(TB1 - 4 and 5) Normal Blow
7-39
7-40
Appendix A
Compatible Devices
TABLE 2
ANALOG ADDRESSABLE DEVICES
Device
TABLE 1
CONVENTIONAL DEVICES
Detector
Base
Installation
Instructions
CZM-1B6
DB-3S
315-081943-15
CZM-1B6
1,6
DI-B3/B3H
AD-3I/ILP
AD-3RI/3RP
315-093234-4
315-086591-7
CZM-1B6
DT-11
DB-11
315-095429-1
DB-3S + DB-ADPT
CZM-1B6
PBA-1191
PBB-1191
315-095424-2
PE-3/3T
DB-3S
AD-3ILP
AD-3RP
315-090875-6
315-093234-4
315-086591-7
PE-11/PE-11T
DB-11
315-094198-3
DB-3S + DB-ADPT 315-094198-3
AD-11P/11PR
315-095659-2
5,7
FP-11/FPT-11
Compatible With
DI-3/3H
DI-A3/A3H
CZM-1B6
CZM-4
1,6
CZM-4
1,6
CZM-4
1,6
S121/S122 + ISI-1
DB-3S
FP-11 (d) 8, 10
315-095355-2
DB-11, DB-X11RS
DB-3S + DB-ADPT
315-095921-4
DB-X3RS + DB-ADPT
ADBI-60 + DB-ADPT
315-095659-2
315-095306-3
ID-60I/60IH
ID-60IA/60IAH
DB-3S, DB-X3RS
315-090287-2
CZM-4
ID-60IB/601BH
AD-3I
AD-3XRI
315-093234-4
315-093235-4
CZM-4
ILI-1/1H
ILI-1A/1AH
DB-3S, DB-X3RS
315-095387-1
CZM-4
ILI-1B/1BH
4
AD-3I
AD-3XRI
315-093234-4
315-093235-4
ILP-1/ILPT-1
DB-3S, DB-X3RS
315-092594-5
AD-3ILP
AD-3XRILP
315-093234-4
315-093235-4
DB-3S, DB-X3RS
315-095028-1
AD-3ILP
AD-3XRILP
315-093234-4
315-093235-4
DB-3S
315-093336-1
MSI-10/20
315-090903-3
MSI-10B/20B
315-093329-1
MSI-B6F
315-095302-1
MSI-MB6
315-093613-1
TRI-B6/6D/6R
315-093315-3
TRI-B6M
315-094547-1
TRI-S/D/R
315-096242-2
CZM-1B6
1,6
315-081943-15
CZM-1B6
2,6
315-085258C
CZM-1B6
ICP-B6
ILPT-1(d)
ILP-2
ILP-2(d) 9, 10
1. May use up to 15 detectors of any type.
2. May use up to 10 DI-3IS ionization detectors in addition to mechanical (non-energy storing)
shorting devices.
3. May use up to five S121 or S122 flame detectors in addition to mechanical (non-energy
storing) shorting devices.
4. May use up to 30 detectors of any type, except PB-1191.
5. Do not use with alarm verification.
6. Do not use detector operated accessories with CZM-1B6.
7. Only one PB-1191, and no additional device, can be connected to a CZM-4 initiating zone.
8. The FP-11 is only compatible with MXL-IQ Rev. 6.0 or greater firmware.
9. Must use MXL-IQ Rev 3.0 or greater firmware.
10. When the CSG-M is configured, the DUCT application must be selected when the device is
used in an air duct housing or in a spot duct application.
Installation
Instructions
AD-11P/11XPR
FM Approved Only
DI-3IS + ISI-1
Base
ILT-1
A-1
Appendix A
A-2
Appendix B
Device Analog Voltages

DETECTOR VOLTAGE RESPONSE
Device
Input State
Voltage
Response
CZM-1B6
Normal
Alarm
Trouble
0.50-4.19
4.20-5.0 0
0.0 0-0.47
ID-60T-135
ILT-1
Normal
Alarm
Trouble
1.80-3.0 0
3.10-5.0 0
0.0 0-1.79
MSI-10/20
Normal
Alarm
Trouble
1.80-3.0 0
3.10-5.0 0
0.0 0-1.79
MSI-10B/20B
Normal
Alarm
Trouble
1.80-3.0 0
3.10-5.0 0
0.0 0-1.79
MSI-MB6
Normal
Alarm
Trouble
1.80-3.0 0
3.10-5.0 0
0.0 0-1.79
MSI-B6F
Normal
Alarm
Trouble
1.80-3.0 0
3.10-5.0 0
0.0 0-1.79
MS-MI
Normal
Alarm
Trouble
1.80-3.0 0
3.10-5.0 0
0.0 0-1.79
TRI-60/60D/60R
Not Available
Not Available
TRI-B6/B6D/B6R
Not Available
Not Available
TRI-B6M
Not Available
Not Available
Dust
Supervisory
Trouble
4.25-5.12
4.12-5.0 0
4.0 0-4.88
3.88-4.75
3.75-4.63
3.63-4.50
3.50-4.38
0.63-4.12
0.63-4.0 0
0.63-3.88
0.63-3.75
0.63-3.63
0.63-3.50
0.63-3.38
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
5.25-10.0 0
5.12-10.0 0
5.0 0-10.0 0
4.88-10.0 0
4.75-10.0 0
4.63-10.0 0
4.50-10.0 0
4.25-5.12
4.12-5.0 0
4.0 0-4.88
3.88-4.75
3.75-4.63
3.63-4.50
3.50-4.38
0.63-4.12
0.63-4.0 0
0.63-3.88
0.63-3.75
0.63-3.63
0.63-3.50
0.63-3.38
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
0.0 0-0.50
ID-60P
LOW3
LOW2
LOW1
NOR M
HI-1
HI-2
HI-3
5.12-10.0 0
5.0 0-10.0 0
4.88-10.0 0
4.75-10.0 0
4.63-10.0 0
4.50-10.0 0
4.38-10.0 0
4.12-5.0 0
4.0 0-4.88
3.88-4.75
3.75-4.63
3.63-4.50
3.50-4.38
3.88-4.25
0.88-4.0 0
0.88-3.88
0.88-3.75
0.88-3.63
0.88-3.50
0.88-3.38
0.88-3.25
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
ILP-1/ILPT-1
ILPT-1(d)
LOW3
LOW2
LOW1
NOR M
HI-1
HI-2
HI-3
5.12-10.0 0
5.0 0-10.0 0
4.88-10.0 0
4.75-10.0 0
4.63-10.0 0
4.50-10.0 0
4.38-10.0 0
4.12-5.0 0
4.0 0-4.88
3.88-4.75
3.75-4.63
3.63-4.50
3.50-4.38
3.88-4.25
0.88-4.0 0
0.88-3.88
0.88-3.75
0.88-3.63
0.88-3.50
0.88-3.38
0.88-3.25
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
ILP-2
(In Default/No
Application
Mode Only)
LOW3
LOW2
LOW1
NOR M
HI-1
HI-2
HI-3
5.12-10.0 0
5.0 0-10.0 0
4.88-10.0 0
4.75-10.0 0
4.63-10.0 0
4.50-10.0 0
4.38-10.0 0
4.12-5.0 0
4.0 0-4.88
3.88-4.75
3.75-4.63
3.63-4.50
3.50-4.38
3.88-4.25
0.88-4.0 0
0.88-3.88
0.88-3.75
0.88-3.63
0.88-3.50
0.88-3.38
0.88-3.25
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
0.0 0-0.75
Detector
Sensitivity
Alarm
ID-60I/60IH
ID-60IA/60IAH
ID-60IB/601BH
LOW3
LOW2
LOW1
NOR M
HI-1
HI-2
HI-3
5.25-10.0 0
5.12-10.0 0
5.0 0-10.0 0
4.88-10.0 0
4.75-10.0 0
4.63-10.0 0
4.50-10.0 0
ILI-1/1H
ILI-1A/1AH
ILI-1B/1BH
LOW3
LOW2
LOW1
NOR M
HI-1
HI-2
HI-3
Threshold
B-1
Appendix B
B-2
Appendix C
MXL-IQ Battery Calculations

Battery backup is a requirement for the
MXL-IQ. To determine the size battery you
must use, follow the procedures listed
below. The MXL-IQ can charge a battery
of up to 55 amp hours. A battery size
calculation form is also provided.
1. Record all the modules required in the
form on the following page.
2. Calculate each row across and place
the total in the right column: Total
Standby 24 VDC Module Current
3. Total the right-hand column and record
it at the bottom of the form opposite
Total System Current.
5. Multiply the AH Total by 1.3 to obtain

the final battery amp hour capacity and
record it opposite Battery Size.
Three battery models are UL listed for use
with the MXL-IQ:
BP-6124V, 15 AH
BTX-1a set of 12V, 31 AH
BTX-2a set of 12V, 55 AH
Select the battery that meets or exceeds
the final calculated battery amp hour rating.
Use an external battery box with the BTX-2
model.
4. For NFPA 72 Local, 72 Proprietary,

and UL 1076 systems multiply the total
system current by 24 and record it at
that Total AH location.
or
For NFPA 72 Municipal Tie and 72
Remote Station systems multiply the
total system current by 60 and record it
at that Total AH location.
or
For FM Approved Deluge/PreAction
systems multiply the total system
current by 90 and record it at that Total
AH location.
C-1
Appendix C
NOTES
The following modules draw
no 24 VDC current and do
not need to be included in
the battery calculations:
MOM-2
MOM-4
TSW-2
1. Use this column for
battery size calculations.
2. Power is supplied by a
separate UPS.
3. EOL currents included.
C-2
Load Current Per Circuit

Standby 24 VDC
Total Standby 24
Module
Quantity Module Current
VDC Module
(See Note 1) End of Line Device Device Current
Current
175mA
SMB-2
12mA per NAC
1.1mA per device
MKB-4
5mA
0
0
RCC-1/1F
75mA
0
0
TSP-40
70mA
0
0
10mA
0
CSM-4
12mA
15mA
CRM-4
15mA per active
relay
55mA
CZM-4
0
3mA
105mA
ALD-2I
0
1.1mA per device
CMI-30 0
30mA
0
0
NIM-1R
70mA
0
NA
MOI-7
120mA
0
0
MOD-16
2mA
0
0
MID-16
2mA
0
0
6mA
CZM-1B6
5mA
NA
ICP-B6
18mA
2.5mA
NA
PIM-1
10mA
0
NA
PIM-2
(See Note 2)
0
NA
PAL-1
(See Note 2)
0
NA
D230 0CP
50mA
0
0
Silent Knight
60 mA
0
0
Total System Current
NFPA Local (72A), Proprietary (72D), UL 1076 (MMB-2 only) - Total AH x 24 =
NFPA Municipal Tie (72B), Remote Station (72C) - Total AH x 60 =
FM Approved Deluge/PreAction - Total AH x 90 =
Battery Size (with Alarm Reserve Correction) x 1.3 =
Appendix D
MXL-IQ Power Supply Load

Calculations
Each MXL-IQ System enclosure requires
an SMB-2. To ensure that the power supply
is not overloaded, complete the worksheet
on the following page.
Enter the quantity of each module in
the enclosure.
Calculate both the 24V and 5V loads
for each row.
Total the Active 24V and Active 5V
columns.
Ensure that both totals are within the
power supply output ratings in the
table to the right.
POW ER S U PPLY OU TPU T R ATI NGS

A ct iv e 2 4 VDC
M odule C ur r ent
A ct iv e 5 VDC
M odule C ur r ent
SMB -2/MPS -6
6 a mp s
500mA
SMB -2/MPS -12
12 amps
500mA
M odule
D-1
Appendix D
The following modules

draw no current from
either the 5 VDC or 24 VDC
power supplies and do not
need to be included in
these calculations:
MOM-2
MOM-4
PAL-1
PIM-2
TSW-2
Module
Quantity
SMB-2
(See Note 3)
MKB-4
D-2
Total Active
24 VDC Module
Current
(See Note 1)
Active 5 VDC
Module Current
Total Active
5 VDC Module
Current
(See Note 2)
(See Note 3)
0
15mA
RCC-1/1F
80mA
TSP-40
70mA
CSM-4
34mA + 1.5A
max per circuit
30mA
CRM-4
75mA
30mA
CZM-4
720mA
4 zones in
alarm
24mA
ALD-2I
105mA + 1.1mA
per device
CMI-30 0
96mA
NIM-1R
160mA
MOI-7
1. Use this column to

calculate total current
from 24 VDC supply to
make sure it is not
overloaded.
2. Use this column to
calculate total current
from 5 VDC supply to
make sure it is not
overloaded.
3. SMB-2 supplies 5V at
500mA, 24V at 6A (MPS6), 24V at 12A (MPS-12).
Active 24 VDC
Module Current
120mA
175mA
MOD-16
850mA max
2mA
MID-16
32mA max
2mA
50mA
ICP-B6
1.5A
PIM-1
25mA
D230 0CP
20 0mA
CZM-1B6
Silent Knight
130mA
TOTAL
0
TOTAL
Appendix E
Alarm Verification
The Alarm Verification feature provides the
MXL-IQ with a way to verify an alarm from
area type addressable smoke detectors
connected to the analog loops or from
standard smoke detectors connected to
the CZM-4 module. This feature reduces
the incidence of false alarms.
When a detector is supervised with Alarm
Verification, it is turned off immediately
after the System first detects alarm
causing data from it.
The length of time that the detector is
verified is fixed at 50 seconds. In MXL-IQ,
an addressable detector is turned off by
the System ignoring its data; a standard
detector is turned off by the power actually
being removed from the detector. After the
turnoff period, the panel puts that detector

into alarm if it has alarm causing data within
60 seconds of being turned back on. See
the figure below for a graphic illustration of
Alarm Verification
You can select Alarm Verification for none,
all, or any combination of addresssable
smoke detectors.
MXL-IQ supports a global verification
feature called Device Confirmation. It
provides adjustable AB verification times
for all addressable:
Ionization detectors
Photo detectors
Ionization and photo detectors
A____________________B________________________C
Time
A
AB
BC
Time at which the System initially recognizes an alarm from a smoke detector.
The 50 seconds during which the System ignores the alarm data
The 60 seconds during which the System alarms if the device is returning alarm data
CAUTION
Use only detectors
which are subjected to air
velocities of less than 100
feet per minute with Alarm
Verification. Under dynamic
air velocity conditions,
smoke may be swept from a
smoke detector after the
initial alarm. That may cause
a long delay before
verification. Do not select
Alarm Verification for such
applications.
Line Graph of Alarm Verification
E-1
Appendix E
With Device Confirmation, the BC
verification time known as System Justified Alarm time is also adjustable. It is the
same time used by both ionization and
photo detectors. If a device is individually
selected for alarm verification, the alarm
verification feature takes priority over the
device confirmation option. For adjustment
ranges, refer to the CSG-M Programming
Manual, P/N 315-090381.
E-2
There is an Override menu selection in the

Test menu of MXL-IQ. Select Alr_Verify to
disable all alarm verification or select
Alr_Confirm to disable all alarm confirmation for a period of up to 4 hours or until
manually re-enabled.
Appendix F
Envirolink
INTELLIGENT ENVIRONMENTAL COMPENSATION (IEC)

Envirolink is an optional feature that permits
MXL-IQ to compensate automatically for
environmental changes (such as dirt and dust
buildup) in the analog voltage of an I Series
photo or ion smoke detector. The selection of
Envirolink devices is made in the CSG-M.
Once a detector is chosen to be covered by
Envirolink, MXL-IQ stores and analyzes the
analog readings of the smoke detector and
adjusts the detectors threshold upward or
downward, as necessary, to maintain a
constant sensitivity.
SENSITIVITY
VOLTAGE
Analog Voltage
As the analog voltage increases due to

environmental factors, an equivalent
increase in the detectors alarm threshold
prevents factors other than smoke from
causing an alarm. This method maintains
the selected detectors sensitivity.
Typically, the analog voltage changes
slowly over long periods of time for environmental factors, but changes quickly over
short periods of time for actual smoke.
Initial System Power-Up

When a new or modified CSG-M is loaded
into a system, the MXL-IQ control panel
goes through an initial system power-up.
The MXL-IQ does not keep the Envirolink
option where it was formerly applied when
this new system powers up. The Envirolink
memory re-initializes, and then MXL-IQ
begins adjusting the alarm thresholds
wherever Envirolink is selected in the new
CSG-M.
Alarm
Threshold Voltage
0 Volts
Adjusting the Alarm Threshold

When a New CSG-M is Uploaded
After MXL-IQ checks that the actual ID of a
device with Envirolink agrees with the
CSG-M, it adjusts the detectors alarm
threshold according to the data stored. The
first adjustment occurs after 100 hours of
data accumulation. In the case of power
cycling or resetting, adjustments begin
within 90 seconds.
F-1
Appendix F
If a detector with Envirolink (IEC) reports an
alarm condition before the detectors alarm
threshold is adjusted, the alarm delays until
the alarm threshold is adjusted. If the device
continues to report an alarm condition once
its alarm threshold is adjusted, the alarm
reports.
If the CSG-M and the device ID do not agree,
the IEC for that device does not activate
until the trouble condition is removed from
the system and the panel is reset.
MXL-IQ Power On
When a system is brought on-line, or when
there is a complete loss of power in an
MXL-IQ enclosure containing detectors with
IEC applied, the operator must perform a
reset sequence for the IEC devices in that
MXL-IQ and also reset the MXL-IQ.
When an MXL-IQ is powered the first time,
and there is no data for IEC devices, MXL-IQ
leaves these devices at the default alarm
threshold. However, if former IEC data is
available, MXL-IQ adjusts the device alarm
threshold accordingly.
Ongoing Adjustments of the

Alarm Threshold
Environmental conditions usually cause a
small change in the analog voltage over a
long period of time. At regular intervals
MXL-IQ collects analog data for each
detector with IEC and adjusts the alarm
threshold accordingly. MXL-IQ adjusts for
both up and down changes in the analog
voltage. In addition, if system power is lost,
MXL-IQ adjusts the alarm thresholds as
needed by using stored data.
Indicating IEC Trouble Conditions

A trouble condition involving the IEC may
be annunciated by the MXL-IQ as:
PRE-DIRTY ANALOG VOLT. REACHED
The trouble conditions shown above are

annunciated on a detector-by-detector
basis as each detector is checked.
MXL-IQ annunciates a trouble condition for
a detector when its alarm threshold
reaches a predetermined limit. The operator should acknowledge the trouble, clean
the detector if possible, and reset the
control panel. If the detector is not cleaned,
the control panel annunciates this trouble
condition after every panel reset until the
detector is cleaned. When it is cleaned, that
is detected by the Auto Clean Detection
feature.
Automatic Cleanliness Detection

MXL-IQ automatically detects when an IEC
detector was cleaned and checks whether
the detector is considered clean by MXL-IQs
standards. If the detector is clean, IEC data
for that device is reset to clean levels, and
the following message prints:
Detector Cleaned
NOTE: Automatic detection and documentation of the cleaning of a detector by

MXL-IQ may take as long as 1 hour. To
avoid this, use the Det cleaned option in
the Test menu to avoid automatic clean
detection. When you enter the address of
the detector that was cleaned, MXL-IQ
adjusts that detectors Norm sensitivity
setting reference.
Detector Cleaned
IEC must be enabled in the CSG-M in order
to have access to the Det_cleaned option
through the MXL-IQ Annunciator Panel.
At the Test menu, use the Left or Right
arrow key to cause the D in Det_cleaned to
start blinking:
TEST: OVERRIDE DET CLEANED
OR
IEC LIMIT REACHED. SERVICE REQ
F-2

select Det_cleaned.
Appendix F
and device numbers.
Type the three-digit module number
and the three-digit device number
(mmm/ddd), including all leading
zeroes.
Press ENTER.
After entering the module-device, MXL-IQ
checks whether the device is subject to
IEC. If the device is not subject to IEC, or if
IEC is not enabled for the system, an error
messages displays:
DEVICE NOT SUBJECT TO IEC

IEC NOT ENABLED IN CSG-M
If the device is an IEC detector, MXL-IQ

displays and prints the time, date, device,
and custom message of the cleaned
device.
F-3
Appendix F
F-4
Appendix G
Latching/Non-Latching Troubles
This feature is not available for Networked
MXL-IQ Systems.
When the Latching/Non-Latching (self

restoring) trouble option is set to YES in the
CSG-M, MXL-IQ automatically removes
trouble conditions from the trouble queue
when the OUT OF TROUBLE condition is
detected.
For NFPA 72 Local, 72 Municipal Tie, and
72 Remote Station systems, the following
criteria must be met in order for the trouble
to be removed from the trouble queue:
Module and device numbers
must be identical
Trouble type must be identical
Both IN/OUT conditions must be
recorded in the queue
All printers being used must print both
IN/OUT conditions
When all these conditions are met, the MXL-IQ
removes both the in and out occurrence of
this trouble from the queue. If there are no
other events in the system (alarm, supervisory, trouble, or security), MXL-IQ returns
to the SYSTEM NORMAL display (without
a system reset). If there are other events in
the system, MXL-IQ updates the display.
For NFPA 72 Proprietary systems, the

following criteria must be met if the trouble
is to be removed from the trouble queue:
Module and device numbers
must be identical
Trouble type must be identical
Both IN/OUT conditions must be
recorded in the queue
All printers being used must print both
IN/OUT conditions
Both IN and OUT conditions must be
acknowledged and printed
When all these conditions are met, MXL-IQ
removes both the in and out occurrence of
this trouble from the queue. If there are no
other events in the system (alarm, supervisory, trouble, or security), MXL-IQ returns
to the SYSTEM NORMAL display. If there
are other events in the system, MXL-IQ
updates the display.
Not all troubles can be removed from the
trouble queue. If there is no OUT condition
reported (i.e., Class A loop trouble), MXL-IQ
requires an acknowledgement and reset.
G-1
Appendix G
G-2
Appendix H
Installing A Security Point

WARNING:
These circuits are

intended for 24 hour
alarm monitoring only.
CAUTION:
When setting the device address using
the FPI-32, select the normally closed
alarm causing input.
UL 1076 requires a TSW-2 tamper switch

as well as a supervised printer (PAL-1/
PAL-2). Other supervised printers that are
selectable in CSG-M are the TI-820 and
the LA-50.
Only Models TRI-60/-60D/-60R or
TRI-B6/-B6D/-B6R may be used as
security points. A COMMUNICATION
FAILURE with a TRI device configured
for SECURITY results in a SECURITY
ALARM as well as a communication
trouble. When installing a TRI device in
the CSG-M, be sure to set the device
usage field to security; otherwise, the
device usage defaults to fire alarm.
TRI-60 / TRI-B6
1
2
3
4
SWITCH
NC
For proprietary burglary application

(UL 1076):
Use a TSW-2 tamper switch to monitor
the main enclosure.
Monitor each TRI-60/-60D/-60R or
TRI-B6/-B6D/-B6R related to this application for 24 hours by using a listed motion
detector (to prevent tampering).
TRI-60R / TRI-B6R
+ ANALOG
- LOOP
OUT
+ ANALOG
- LOOP IN
Connect only one switch per TRI input.
1
2
3
EOL *
3.6K
1/4W
+ ANALOG
- LOOP
OUT
+ ANALOG
- LOOP IN
SWITCH
NC
EOL *
3.6K
1/4W
TRI-60D / TRI-B6D
1
2
3
4
NOT USED
GND
GND
+ ANALOG
- LOOP
OUT
+ ANALOG
- LOOP IN
SWITCH A
SWITCH B
NC
EOL *
3.6K
1/4W
NC
EOL *
3.6K
1/4W
NOT USED
GND
* END OF LINE DEVICE: P/N 140-820185

REFER TO TRI INSTALLATION INSTRUCTIONS,
P/N 315-092329 OR 315-093315, AS APPLICABLE
Installing the Security Point for UL 1076
H-1
Appendix H
H-2
Appendix I
Application Specific Detection

(ASD)
Application Specific Detection (ASD)
allows the system designer (and anyone
with Control menu access) to program an
ILP-2 detectors sensitivity, pre-alarm
threshold, and other alarm-related parameters using English descriptions of the
detector's environment (application). This
eliminates the need for detailed knowledge
of smoke detector terminology and
operation. The designer can set all of the
critical detector parameters by simply
selecting an application description that
closely fits the one where the detector is to
be installed.
For example, to use ASD to select the
optimal parameters for a detector in a hotel
lobby, select the LOBBY application in the
CSG-M for that device. The MXL will
automatically transmit the factory determined sensitivity, pre-alarm threshold, and
detection algorithm (R-algorithm) to the
corresponding device. This eliminates the
guesswork of selecting these parameters
for different environments. Changes made
at the control panel using the Control menu
(Change_Apps) override the ASD settings
made in CSG-M for that ILP-2 device until
the next power-on reset.
NOTES:
1. The ILP-2 is only compatible with MXL-IQ Revision 3.0 or
greater firmware.
2. The FP-11/FPT-11 is only compatible with MXL-IQ Revision
6.0 or greater firmware.
3. When the CSG-M is configured, the DUCT application
must be selected when the device is used in an air duct
housing or in a spot duct application.
ASD SUBMENU ABBREVIATIONS

MXL
Menu
CSG-M Application
NONE
Disable
OFFC
Office (Retail)
WHSE
Warehouse (Light
Manufacturing)
LOBY
Lobby
Relatively clean area, temperature changes,

cellular phones, smoking
COMP
Computer Room
Very controlled environment, clean,

temperature closely regulated, high cost
clean machinery operating, no smoking, high
air velocity
DORM
Dormitory
Airborne dust and temperature changes,

living quarters, cooking fumes, smoking
HLTH
Healthcare
Higher level risk, relatively clean, electronic

equipment
PARK
Parking Garage
UTIL
Utility (Transformer)
Room
PREC
Precious Storage
(Sensitive
Environment)
HOST
Hostile Environment
DUCT
Duct (Open air or

duct housing)
Description
No Applications (Standard Photoelectric
Detector)
Reasonably clean, climate controlled
atmosphere
Airborne dust, equipment, fork truck and
light to medium dock area exhaust fumes
Airborne dust, car and diesel fumes,

temperature swings
Normal to somewhat dirty environment, heat
from running equipment
Sensitive materials or equipment storage,
clean dust-free environment, earliest
warning desired
Dirty, dusty, humid, operating equipment, RF
present, wide temperature swings
Dirty, dusty, humid, wide temperature
swings, high air velocity
I-1
Appendix I
Testing ASD Devices

Since one of the parameters transmitted to
the detector adjusts the detection algorithm (R-algorithm) to reduce false alarms,
it is necessary to defeat ASD (or at least
the R-algorithm) when smoke testing ASD
devices. The Test ASD_Devices menu
option has been supplied for this purpose.
When ASD devices are to be smoke
tested, the Test ASD_Devices option must
be enabled. This disables the application
specific detection R-algorithm so the
detector will alarm using the standard test
gas method. If the Test ASD_Devices
option is not enabled prior to smoking the
I-2
device, the tester may find it extremely

difficult to alarm the detector since the
algorithms are designed not to be fooled by
a deceptive phenomenon such as test gas.
Once the Test ASD_Devices option has
been enabled using the test menu, the tester
should wait 3 minutes before attempting to
test the ASD devices. This time may vary
slightly with the number of ALDs and ASD
detectors in a system. This will ensure that
the ASD R-algorithm has been defeated for
test purposes. The system will not reset until
the Test ASD_Devices option has been
disabled.
Appendix J
Trouble Message
The Probable Cause Is:
MXL-IQ Trouble Messages

Trouble Message
AC Fail or Brownout
Primary AC power is missing or below the

brownout level; the System is running on
battery backup.
Airflow Too Low
AnaLASER airflow is below programmed

threshold.
Airflow Too High
AnaLASER airflow is above programmed

threshold.
AnaLASER Power Trouble
Problem with AnaLASER power supply.
ASD Testing Enabled
Application specific detector testing is

enabled. The applications feature is
disabled during testing.
Aux Pwr Class A Fail Neg
The negative side of the CZM-1B6 power

circuit is open.
Aux Pwr Class A Fail Pos
The positive side of the CZM-1B6 power

circuit is open.
Battery Backup Invalid
A battery is connected, but not selected in

CSG-M.
Battery Fuse/Wiring Open
Either the battery is not connected, or the

battery fuse is blown, or the battery voltage
is too low.
Carrier Lost
CMI-300 to CXL communications problem

where the CMI-300 does not see the CXL's
modem carrier (tone). No data is being
transmitted.
Class A Loop Trouble
If Class A: The initiating circuit at this

module address has an open.
If Class B: Wired zones are missing the
Class A jumpers.
J-1
Appendix J
J-2
Trouble Message
CMI-300 General Trouble
Communications trouble between the CMI300 and the CXL. Data is attempting to
transmit.
CSGM Out Of Date
This MXL-IQ (node) will need to be updated

with the latest CSG-M networked program.
A network CSG-M has been loaded on
another MXL-IQ (node) and has a reference
to this MXL-IQ (node).
Daily Detector Test Abnormal
Device is defective.
Detector Trouble
AnaLASER detector in need of repair.
Device Communication Error
An analog device whose response has

failed error checking.
Device Detected Waveform Error
An analog device reports this trouble if it

receives an unknown polling waveform.
Device LED Turned On
A device LED was turned on from the Test

menu of the MXL-IQ.
Device Multiple Response
Two or more analog devices at the same

address have reported during normal
supervision.
Device Out of Calibration
This message is used with XLD and is the

same as the XL-3 message,
Response out of window at cal.
Device Receive Error
An analog device reports this trouble

if it receives an incorrect analog
transmission.
Event log 80% full
Use extract history in CSG-M to reset the

MXL-IQ history log.
Event log 90% full
Use extract history in CSG-M to reset the

MXL-IQ history log.
Function Recursion Trouble
The number of evaluations of output logic

required until outputs are stable has
exceeded the system maximum. Rewrite
CSG-M to simplify functions.
Ground Fault Minus
Low impedance to the negative side of one

of the field wiring circuits to earth ground.
Appendix J
Trouble Message
Ground Fault Plus
Low impedance to the positive side of one of

the field wiring circuits to earth ground.
High Battery Voltage
Battery voltage is too high because battery

has been overcharged. Battery and/or
charger are possibly defective.
History Manually Turned Off

History Manually Turned On
History Manually Erased
History Log has been manually changed

(Turned Off / Turned On / Erased) using
the MKB.
IEC Limit Reached. Service Req
Detector environmental compensation has

reached UL limit. Detector is very dirty and
requires cleaning.
IEC/Pre-alarm Memory Error
An unsuccessful attempt was made to

access the IEC area of flash memory. Is
IEC-1 module present? Is segmented flash
present?
Incorrect Device ID
An analog device whose type or usage does

not agree with the CSG-M assignment at
that address.
Incorrect Node Address
Address on NIM-1R is incorrect.
Input Device Not Responding
A device assigned in CSG-M is not reporting

at its address.
Input Dev Response Too Low
Input wiring to TRI or CZM-1B6 modules

has an open circuit or no EOL. Loss of
power to CZM-1B6 module. Smoke detector
chamber defective.
Input Device Requires Service
An ion or photo detector has exceeded the

80% dust threshold.
Input Disarmed
An initiating device was disarmed through

the Control menu.
Keyswitch Activated (CANADA)
This is a trouble type for activation of

Canadian manual station keyswitch if no
alarm is present.
Lamp Supervision Trouble
MID-1 input trouble when used for lamp

supervision.
J-3
Appendix J
J-4
Trouble Message
Log FULL, Events Will Be Lost
History Log is full. Use extract history in

CSG-M to reset the MXL-IQ history log
Loss of 24V Input Power
A CZM-4 has lost its 24 VDC input.
Low Battery Voltage
Battery voltage readings low; the battery

requires recharge/replacement.
Low IEC Voltage, Service Req
Defective device.
Memory Error In RAM Test
An error was detected in RAM memory IC

112 or IC 113.
Memory Error in ROM test
An error was detected in the EPROM IC

111 or IC 110
Memory Upgrade Required
Starting with revision 6.00, the MXL-IQ

requires a memory upgrade (RAM) in
socket IC113.
Missing Device ID Response
An ALD module has not returned an ID Poll

response for any of its detectors or devices.
NOTE: This trouble will accompany module
not responding for missing ALD modules.
Module Comm Failure
When network communications are

interrupted, and then restored, all module
addresses affected report this trouble.
Module Not Responding
The module assigned in CSG-M at this

address is not responding.
Module RAM Failure
The CRM-4, CSM-4, or CZM-4 at this

address has determined that its internal
RAM is not operating properly.
Module ROM Failure
The module at this address has a ROM

checksum failure.
MOI-1 Local Trouble
This trouble is reported when the TRBL IN

input of the MOI-7 is driven high.
MOI-1 Voice System Trouble
This condition is caused by driving the

TRBL IN of the MOI-7 high with voice
modules configured in CSG-M for this
module.
Appendix J
Trouble Message
MOI-1 Zone Disarmed
Output of an MOI-7 (MOD-16 or VPM-5)

has been disarmed at the MXL.
More Than 60 Alarms
The System alarm queue is full, and more

alarms have been received.
More Than 60 Securities
The System security condition queue is

full, and more security conditions have
been received.
More Than 60 Supervisory
The System supervisory queue is full, and

mor supervisories have been received.
More Than 60 Troubles
The System trouble queue is full, and

more supervisories have ben received.
Multiple Module Response
Two or more modules respond at the

same address.
Multiple Response Analog Poll
Two or more analog devices at the same

address have reported during an analog
data request.
MXL Network Failure
The MKB/RCC has lost communication

with the MNET.
Network CSGM Upload Needed
A function was added to an XNET node

and had a reference to another node. This
function shall be added to each node it
references.
Network Input Disarmed
A point on another XNET node has been

disarmed.
Network Loop A Failure
The Style 7 primary (A) RS485 MNET

network loop has failed.
Network Loop B Failure
The Style 7 secondary (B) RS485 MNET

network loop has failed.
No CSG - Default In Use
No CSG-M custom programming was

found in FLASH memory so the system is
using the default CSG-M.
Node Disconnected
XNET node was logically disconnected

from the NCC.
Node Multiple Response
Two nodes are programmed at the same

address.
J-5
Appendix J
J-6
Trouble Message
Node Not Responding
XNET wiring and/or NIM-1R module is

defective.
Out of RAM Call Pyrotronics
The configuration upload is too large.
Out of Tasks Call Pyrotronics
Contact the Siemens Building Technologies, Inc. Technical Services Department.
Output Disarmed
Indicates that an output point has been

manually disarmed.
PRE 1 Level
PRE 2 Level
AnaLASER device has reached its

pre-alarm setting.
Pre-alarm
Device has reached its pre-alarm setting.
Pre-dirty Analog Volt. Reached
IEC compensation has reached a level

where the detector should be cleaned.
Printer Off Line/Fault
A supervised printer is not responding.
Printer Out Of Paper
The printer has run out of paper.
Relay Coil Open
The relay coil at this address is open.
Relay Disarmed
The relay at this address has been disarmed from the Control menu.
Relay Driver Inoperative
The relay on the CRM-4 or CSM-4 at this

address does not operate when commanded to energize.
Relay Supervision Failure
The relay at this address has a coil failure.
ROM SW Version Error
Module at the address noted needs an

update to latest available software level.
Signal Circuit Disarmed
The NAC at this address was disarmed

from the Control panel.
Signal Circuit Loop Open
The NAC at this address has a broken wire

or missing EOL device.
Signal Ckt Loop Shorted
The NAC at this address is shorted, or the

EOL device is the wrong value, or the
notification appliances are not polarized or
are connected backwards.
Appendix J
Trouble Message
Signal Mod A/D Convert Fail
The CSM-4 at this address has a failed

analog-to-digital converter.
Signal Module Zone Code
Zone code failure on the CSM-4 module.
Software Key Violation
Incorrect Software Key Installed (NCC

only).
Stack Fault Call Pyrotronics
When the message Call Pyrotronics

appears, a four letter Alpha ID will be
displayed. This number is necessary when
reporting the problem to Siemens Building
Technologies, Inc.
Style 4 Network Mode
The Style 4 jumper on a NET-7 is found on

a Style 7 system. Move the jumper to the
Style 7 position.
Style 7 Network Mode
The Style 7 jumper on a NET-7 is found in

the Style 4 mode. Move the Style 7 jumper
to the Style 4 position.
System Commissioning Mode
The system has been put in the commissioning mode.
System Signal Power Failure
A CSM-4 has lost power to its output

circuits.
Tamper Switch
This is a security-type message for the

tamper switch on the SMB-2 board when
the system is selected for UL 1076 operation.
Too Many ALD-2s
To many ALD-2Is are installed on the system.

This is beyond the maximum allowed.
Trouble Causing Input
A device programmed on the system as

trouble causing has been activated and has
changed state.
Trouble Type Not Defined
Unspecified trouble has been received from

this address.
Troubles Summarized
While the system is in the commissioning

mode, the modules will display this message
in lieu of all the devices on this module.
Unspecified Dev Responding
An analog device has reported at an

address not assigned in CSG-M.
J-7
Appendix J
Trouble Message
Unspecified Mod Responding
A module has reported at an address not

assigned in CSG-M.
Unspecified Node Responding
NIM-1R address on another node is

incorrect.
The network CSG-M is incorrect.
J-8
WALKTEST Activated
The MXL-IQ has been placed in the walk

test mode.
Warm Reset
The hardware reset input to the MXL-IQ

was used.
Watch Dog Circuit Triggered
The watch dog circuit on the

SMB-2 triggered.
Zone Loop Open
Broken wire on CZM-4 circuit.
Zone Loop Shorted
Shorted wire on CZM-4 circuit.
Zone Power Loss
The CZM-4 zone at this address has lost its

24 volt input.
Appendix K
Power Limited Wiring

For power limited wiring refer to the following Installation Instructions:
Enclosure
Installation
Instructions
LLM-1
315-093530-2
MSE-3
315-093831-1
MSE-3L
315-095445-1
K-1
Appendix K
K-2
Appendix L
New Two Stage Alarm
For use in Canada only with MXL-IQ software version 1.0 and higher
Canadian Two Stage Alarm is available

with revision 1.0 of MXL-IQ firmware and
revision 6.07 of CSG-M. All new installations
of Two Stage Alarm should use the new
implementation.
The hardware requirements for the Two
Stage Alarm are as follows:
MXL-IQ firmware revision 1.0 or higher
CSG-M revision 6.07 or higher
CSM-4s must contain revision 4 or
higher
The new Two Stage implementation is
designed for flexibility. It allows the system
designer/programmer to define how Two

Stage alarm should function.
Selecting Two Stage

A new selection in the CSG-M determines
which version of Two Stage Alarm is used
in an MXL-IQ. In the Other System Flags
menu (under the Options, System Message, Authorizations menu), a YES/NO
option has been added for New Two Stage
Configuration. This flag determines which
implementation of Two Stage alarm is used
in the MXL-IQ.

Other System Flags
CONFIG => TWOSTG
Sensitivity Adjustments Allowed ----------------->

Block Alarm and Trouble Acknowledge Allowed ----->
Multienclosure System --------------------------->
Device disarm through RESET --------------------->
Self restoring troubles ------------------------->
NFPA 71 connection ------------------------------>
NET 7 panel checking ---------------------------->
NO
YES
NO
NO
NO
NO
NO
Network Repeater Used ---------------------------> NO

Independent Function Keys -----------------------> NO
New Two Stage Configuration ---------------------> YES
Move Cursor to Select, ENTER to TOGGLE
ESC = Prev. Menu
CSG-M Other System Flags Menu
L-1
Appendix L
Select NO for the old system flag
driven version of Two Stage
Select YES for the new control function
version of Two Stage
NOTE: When recompiling an older implementation of Two Stage Alarm under
CSG-M 6.07 or higher, make certain that
the New Two Stage Configuration flag is
set to NO before compiling and uploading
to the MXL-IQ.
Two Stage Signal Circuit Output

Definition
The output for all the coded audibles must
be defined on a system basis. This is done
in CSG-M from the Options, System
Message, Authorizations menu. The Zone
Coded Audible Format menu item determines the systems Two Stage audible
definition. The following nine selections are
provided for Two Stage audibles:
Zone codes must be entered on a point

by point basis.
Zone codes will be output first by
priority, second by queue order.
In order to have the codes sound in the
queue order only, all priorities must be
the same.
Two Stage Control Function (CSG-M)

This function has two inputs and an output
list.
The inputs are labeled Stage 1 and Stage 2.
The inputs may contain the following items:
a device address
function output (logic, timer, etc.)
system flag reference
The output may only be a list of CSM-4 or
main board signal circuits. The signal
circuits referenced must be zone coded
audibles.
The following table describes how the Two
Stage Control Function works.
Two Stage Audible - 30/120 SPM

Two Stage Audible - 30 SPM/Steady
Two Stage Audible - 30 SPM/Temporal
Two Stage Audible - Steady/Steady
Two Stage Audible - Steady/120 SPM
Two Stage Audible - Steady/Temporal
Two Stage Audible - Zone Coded/Steady
Two Stage Audible - Zone Coded/120 SPM
Two Stage Audible - Zone Coded/Temporal
TWO STAGE CONTROL FUNCTIONS
Note that each selection contains a slash (/)

which separates the Stage 1 audible signal
from the Stage 2 audible signal as shown in
the following example.
Stage 1
Input
Stage 2
Input
Coded Audibles in
Ouput List
False
False
Silent
True
False
Stage 1 Audible Signal

For example: 30 SPM,
steady or zone coding
False
True

steady or temporal
True

steady or temporal
Example:
Stage 1 audible
Stage 2 audible
Two Stage Audible - 30 / 120 SPM

slash
When zone coding is selected for Stage 1,

the system displays the Zone Coding
Characteristics menu. (See Figure on the
next page.) This menu allows the system
designer to program the number of rounds,
minimum number of rounds, etc. The final
state will always be STEADY no matter
what is selected in this menu.
L-2
True
Multiple Two Stage control functions may

be used in a configuration. A single coded
audible may appear on the output list of
more than one Two Stage control function.
Due to the potential conflict between the
functions controlling the same coded
output, the following rule applies to the Two
Stage control function:
Appendix L

CONFIG => TWOSTG
System Message ----------------->

Authorization Code-Level 1 ----->
COUNTRY where installed -------->
Language Selection ------------->
NFPA System Designation -------->
Backup Power Type -------------->
Zone Coded Audible Format ------>
Function Evaluation Limit ------>
Photo Detector Confirmation ---->
Ion Detector Confirmation ------>
Sys. Justified Alarm Time ------>
Intelligent Env. Compensation -->
----- CERBERUS Pyrotronics ----11111

22222
33333
Canada
ENGLISH and FRENCH
NFPA A System
15 Amp Hour
TWO STAGE AUDIBLE - ZONE CODED/STEADY
32
0
0
60
OFF
VDT Password Time Out (hh:mm) --> 00:05

Zone Coding Characteristics
ESC=Prev. Menu

Zone Coding Characteristics
# rounds (3-15) ---------------->

Tempo -------------------------->
Final output status ------------>
Inter-digit time (0.5-15 secs) ->
Inter-round time (0.5-15 secs) ->
Inter-group time (0.5-15 secs) ->
Minimum # round (3-15) --------->
Zone Code Alarms After Silence ->
CONFIG => TWOSTG
5
60/MIN
AUDIBLES ON
1.0
2.0
4.0
3
YES
ESC=Prev. Menu
Selecting the Zone Coding Characteristics Menu
L-3
Appendix L
When a coded audible appears on the
output list of more than one Two Stage
control function and there is a conflict
(that is, some functions indicate Stage
1 and some functions indicate Stage
2), then Stage 2 has priority over
Stage 1. As a result, the coded
audibles in question will output Stage 2
(either 120 SPM, steady, or temporal,
as selected).
NOTE: When zone coding is selected as the
Stage 1 audible output, Stage 2 always has
priority over the Stage 1 coding. Once the
coded circuit is driven into Stage 2 by logic,
all zone codes will stop for that circuit no
matter what the minimum rounds are.
There are two keyswitch types available in

the MXL-IQ. All logic associated with a
keyswitch device is CSG-M programmable.
The only MXL-IQ defined aspects of a
keyswitch are as follows:
Keyswitch Type 1
1. If a Type 1 keyswitch is activated, an
alarm event will result.
2. The event will be recorded on the alarm
queue and all standard MXL-IQ functions
associated with an alarm will occur (that
is, the ANY ALARM flag will be set to
TRUE, the ANY NEW ALARM flag will
pulse, etc.).
3. This is true even if there are no previous
alarms.
Two Stage System Flags

There are two system flags associated with
Two Stage alarm: Reset Inhibit and Two
Stage Audible State. Both of these flags
are writable with user-designed logic. Refer
to the following table for Setting the Two
Stage System Flags.
It is important to note that other Two Stage
writable flags used in the previous Two Stage
implementation are not used in the new Two
Stage implementation.
Keyswitch Type 2
1. If a Type 2 keyswitch is activated when
no alarms are present in the system, it
will result in a trouble condition at the
MXL-IQ.
2. If an alarm is detected while this trouble
condition is present on the trouble
queue, the active Type 2 keyswitch will
be added to the system as an alarm
event (added to alarm queue).
SETTING THE TWO STAGE SYSTEM FLAGS
3. If the keyswitch is activated when an

alarm is present in the system, the
keyswitch will be treated as an alarm.
When the Reset Inhibit Then the Normal Reset

flag is held:*
(Red MMB key) is:
All other system behavior is determined by

output logic design.
True
False
Inhibited
Not Inhibited
*The default value of Reset Inhibit is FALSE if the

system does not require a Reset Inhibit.
Sample Two Stage Systems
If the Two Stage Audible Then the Normal Audible

State flag is held:**
Silence (Red MKB key) is:
Using Reset Inhibit with Timer

The figure on page L-5 shows methods of
implementing Reset Inhibit with a timer,
creating an ANY KEYSWITCH function/flag
and a timer based signal silence inhibit
function.
False
True
Inhibited
Not Inhibited
**The default value of Two Stage Audible State is

TRUE if the system does not require a Two Stage
Audible State Inhibit.
L-4
Keyswitch Devices
Keep in mind that your implementation of

these features may vary from the examples
shown. If Reset Inhibit or Two Stage
Audible Silence are not required in your
system, then references to these flags are
not required in the logic design.
Appendix L
Basic Two Stage System
The figure on page L-6 demonstrates a
basic Two Stage system design. Its
operation is summarized below:
reset (provided the RESET INHIBIT

logic permits).
If a keyswitch is activated after the
ANY_ALARM flag is TRUE, the
system will output the second stage
audibles.
In either stage, the audible silence
flag/key controls the silencing and
unsilencing of the coded audibles.
The Panel Reset flag is used to assure
timers and latches are reset for the
next event after reset.
This system will output Stage 1

audibles when the first alarm occurs.
If the alarm is not acknowledged prior
to the expiration of stg1_timer, coded
audibles will be forced output Stage 2
audibles.
If the alarm is acknowledged during
Stage 1, only a keyswitch will place
the system in the second stage.
If the system is reset after the alarm
has been acknowledged and coded
audibles silenced, the system may be
RESET_INH
Any Alarm
Trigger (ALL)
30 Sec
True
SS_INH
Any Alarm
Run
Trigger (ALL)
Reset Inhibit
Run
Enable
True
Two Stage
Audible Silence
Enable
Start Timer
Start Timer
Cancel
Cancel
False
Panel Reset
Typical RESET INHIBIT Timer Function
Typical Signal Silence Inhibit Function
Any_keyswch
Any alarm
Keyswch
List of
Keyswitch
Inputs
OR
(ANY)
AND
(ALL)
Typical ANY KEYSWITCH Function
Using Reset Inhibit with Timer
L-5
Appendix L
Any Alarm
True
Stg1_timer
Run
Trigger (ALL)
Start Timer
Cancel
Enable
Panel Reset
Set
Stg2_enb
Any Alarm
Reset
Clear
Stg2_can
OR
(ANY)
False
Panel Reset
Panel Reset
Audible Silence
In this example, several Two Stage control

functions are used in the system design.
Together with the proper glue logic, a
modified Two Stage system is the result. In
this system, the floors above and below the
alarm signal Stage 1 coded audibles while
the floor of alarm codes Stage 2 audibles.
The general differences between the basic
and complex systems are as follows:
All Alarms Ackd
Any Alarm
any_keyswch
Stg1_to
AND
(ALL)
Stg2_timer
Run
Trigger (ANY)
Enable
Start Timer
Cancel
The first alarm will result in Stage 1

coding on that floor.
An activation of a keyswitch will place
the system in second stage. Therefore, the floors above and below the
alarm will code Stage 1; Stage 2 will
code on the floor of alarm.
If an adjacent floor generates an
alarm, that floor will code Stage 2.
This same principle may be applied to
networked MXL-IQs using external references.
Panel Reset
Audible
Silence
For example: The building in alarm codes

Stage 2 while the adjacent buildings code
Stage 1.
Stg1_ssi
AND
(ALL)
Stg2_sil
OR
(ANY)
Stg2_ran
Set
Reset
Clear
Visual indications are made using MOD-16

outputs. Simply connect the signal in the
logic diagram to the desired LED or other
function to indicate the system stage.
For example: Connect Stage 1 and Stage

2 inputs to an LED function to indicate the
system state.
Stg2_sil
AND
(ALL)
List of Two Stage

Audibles
Stg_ctl
Stg1
Stg2
Audible
Silence
Basic Two Stage System
L-6
Complex Two Stage System

The figure on the next page demonstrates
a more complex Two Stage system. The
basic principles of operation are the same
as the basic Two Stage system with a slight
variation.
NOTE: Since other audibles may be

present in the system besides coded (Two
Stage) audibles, the AUDIBLE SILENCE
LED on the MKB will indicate the state of
the AUDIBLE SILENCE flag as usual. Its
state will only change with manual intervention (manual silence/unsilence).
xxxx
Complex Two Stage System
Stg1_ssz1
To input list of
stg1_ssz1,
stg1_ssz2,
stg1_ssz3
Stg1_timer
Any Alarm
Trigger (ALL)
Run
Enable
Floor 1
alarm pts
Stg1_to
OR
(ANY)
AND
(ALL)
stg2_flr1
AND
(ALL)
Any Alarm
flr1_2stg
Stg1
Audible
Silence
All Alarms Ackd

True
stg1_flr1
stg1_timer
Stg2
Stg2_sils
Floor 1
alarm pts
Start Timer
AND
(ALL)
First Floor
Two Stage
Audible List
Cancel
Stg1_ssz2
Panel Reset
any_keyswch
Stg2_enb
Any Alarm
False
Set
stg1_timer
Floor 2
alarm pts
Stg2_timer
Audible
Silence
Trigger (ANY)
Reset
stg1_flr2
AND
(ALL)
Clear
Stg2_sils
Enable
Panel Reset
Audible Silence
Floor 2
alarm pts
Start Timer
Stg2_can
OR
(ANY)
flr2_2stg
Stg1
Q
stg2_flr2
Run
Panel Reset
OR
(ANY)
Stg2
Second Floor
Two Stage
Audible List
AND
(ALL)
Cancel
Stg1_ssz3
Stg2_sil
stg1_timer
Floor 3
alarm pts
Stg2_ran
Set
L-7
Panel Reset
Clear
Q
Audible
Silence
Audible
Silence
Stg2_sils
OR
(ANY)
stg1_flr3
OR
(ANY)
flr3_2stg
Stg1
Q
stg2_flr3
Use to
indicate
Stage Two
is active
Stg2_sils
Floor 3
alarm pts
Stg2
AND
(ALL)
Third Floor
Two Stage
Audible List
Appendix L
Reset
AND
(ALL)
AND
(ALL)
Appendix L
L-8
Appendix M
Pre-alarm, Dual Criteria Logic

Functions, and Percent Per Foot
Obscuration Features
The pre-alarm feature provides an early
warning of smoke conditions at a more
sensitive reading than alarm level. This
indication can be in the following form:
a displayed and printed pre-alarm
report
output logic control
both
Dual criteria logic allows for the distinction
between the chamber or thermal detector
of the ILPT-1 photo thermal.
The pre-alarm and dual criteria logic
function (ILPT-1 only) features of the ILI or
ILP series of detectors are enabled by the
FPI-32 Field Programmer.
Note:
FPI-32 Rev. 1.3 or higher is

required.
The FPI-32 also gives these detectors new

unique IDs so that they can be identified at
the MXL-IQ as different from the ID-60I and
ID-60P series. The ID-60I and ID60P
detectors still exist in the CSG-M, but the
features described in this appendix do not
apply to them.
CSG-M Software
ILI ion detectors and ILP photoelectric

detectors are available as I/O device types
for ALD-2s (or ALD-2Is). These device types
tell the CSG-M and the MXL-IQ that they
have the features of pre-alarm, dual criteria
(photo thermal only), and ability to display
readings in percent per foot (%/ft) obscuration.
These detectors appear in the CSG-M with
the existing ID-60I and ID-60P detectors.
The MXL-IQs Custom Software Generator
(CSG-M) allows the installation of the ILI or
ILP detectors at any valid ALD address.
Pre-alarm
Pre-alarm must be selected to either
annunciate a detectors pre-alarm or use
the detector in a Criteria Selection function.
Pre-alarm can be enabled at each device
when it is installed as a Yes/No (Y/N) option.
The CSG-M provides the following system
options for pre-alarm:
annunciate (Y/N)
automatic adjust (Y/N)
annunciation type trouble
learning period (1 - 30 days)
activate detector LED (Y/N)
M-1
Appendix M
Dual Criteria Logic Functions

The CSG-M provides a logic function type
labeled Criteria Selection. The following
inputs to this function are a detectors:
pre-alarm (from IL devices or
Analaser),
verification, or
chamber or thermal for the photo
thermal detector (ILPT-1)
Pre-alarm and chamber or thermal selections cannot be mixed in the same function.
The output can be any that is capable of
being driven by output logic, including
sending the output to another function.
Note:
For networked MXL-IQ systems, no

external panel inputs are allowed in
the Criteria Selection function.
MXL-IQ Pre-alarm
Software
Pre-alarm Learning and Setting
The MXL-IQ automatic pre-alarm learning
feature adjusts smoke detector pre-alarm
levels (during the time period selected in
the CSG-M) until they stabilize. Depending
upon pre-alarm activity, the system starts
with the most sensitive pre-alarm level and
gradually adjusts (de-sensitizes) the
MXL-IQ until pre-alarms no longer occur.
The level reached by each smoke detector
at the end of the learning period is the
learned pre-alarm level. No pre-alarms
annunciate or feed output logic during this
learning period.
The learned pre-alarm level is stored in
flash memory so that on a panel power-on,
watchdog, or nickel reset, the pre-alarm
readings still exist. When a new or modified CSG-M is loaded into flash memory,
the MXL-IQ will NOT assume pre-alarm
existed before and will re-start the
learning mode.
The flash memory used for storing prealarm detector readings shares the intelligent environmental control (IEC) flash
memory area. This requires that a boot
block flash device be used if pre-alarm is
enabled. The flash segment size shared by
M-2
IEC and pre-alarm is 8K. Each IEC device

uses 2 bytes and each pre-alarm device
uses 1 byte, allowing a maximum of slightly
over 2500 devices with both IEC and prealarm.
Manual pre-alarm settings can be set at the
MXL-IQ by using the CONTROL PERCENT/FT PRE_ALARM command (See
Pre-alarm and Sensitivity Settings below).
Any valid pre-alarm reading within the
range specified in the table on page M-3
can be used. Pre-alarm adjustments are in
%/ft obscuration. Manual settings override
the learning mode settings. However, they
do not take effect until the end of the
learning period.
Pre-alarm Event Annunciation

Annunciation is a global yes/no option and
the type of annunciation is a trouble. The
trouble report contains the type field text of
Pre-alarm and both the INs and OUTs are
recorded. The format of these trouble
reports is identical to the format of all
existing MXL-IQ trouble or supervisory
reports.
Annunciation of a pre-alarm smoke detector is provided even if the device goes
immediately into alarm. The alarm is
reported first because of its higher priority,
but a pre-alarm or trouble is also generated
thereafter with the same time and date.
Output logic control using the criteria
function with ILI/ILP pre-alarm as the
criteria selection follows the INs and OUTs.
If latching is desired, it must be added in
the CSG-M. Using the criteria selection
function to select either the chamber or the
thermal for the ILPT-1 takes the MXL-IQ an
additional 5 seconds (or more) to evaluate
after the device alarms. This occurs
because a special status poll must be done
to determine whether it was the chamber or
the thermal that caused the alarm. A
criteria function with a selection of alarm
verification provides an output for the
duration a smoke detector is being verified
or until reset if the device alarms.
Pre-alarm and Sensitivity Settings

Pre-alarm and sensitivity adjustments are in
%/ft obscuration and have the following
ranges, increments, and default values:
Appendix M
PHOTO
ION
Pre-alarm adjust
increment
.25% / ft.
.12% / ft.
Pre-alarm range
.25 - 2.0% / ft.
.25 - .75% / ft.
1.5% / ft.
.75% / ft.
Sensitivity adjust
increment
~.25% / ft.
~.12% / ft.
Sensitivity range
1.25 - 3.4% / ft.
.6 - 1.6% / ft.
3.0% / ft.
1.4% / ft.
Pre-alarm
default
Sensitivity
default (Norm)
Because the pre-alarm and sensitivity

settings overlap, set the pre-alarm to at
least an increment below the sensitivity
setting.
Field Programmer Use
The FPI-32 (Rev. 1.3 or higher) must be

used to enable the programming of the ILI
and ILP IDs. The IDs tell the smoke
detector it has the advanced features such
as pre-alarm. For more information about
using the FPI-32 with IL series detectors,
refer to the FPI-32 Programmer/Tester
Operations Manual, P/N 315-090077.
M-3
Appendix M
M-4
Appendix N
MXL-IQ Spare Parts List

Cables
Part Number
SMB-1/-2 to MKB-4
555-192238
SMB-1/-2 to MOM-2/-4 (24V Power)
60 0-290505
SMB-1/-2 to MOM-2/-4 (5V and Data)
555-190506
SMB-1/-2 to Battery
555-190968
SMB-1/-2 to CSG-M Programming Cable
60 0-190704
Fuses
20 Amp MDA Normal Blow
105-292017
15 Amp 3AG Normal Blow
105-224090
105-217858
105-210758
N-1
Appendix N
N-2
Appendix O
New Features for MXL-IQ

Revision 6.0 and Higher
Reset Causing Zone for MID-16 or CZM-4
This powerful feature allows the user to
reset the MXL-IQ by changing the state of
the MID-16 or CZM-4 input. In CSG-M
Revision 10.01, select the new Local Reset
Causing usage for MID-16 or CZM-4 in the
Available Device Usage Types screen:
LOC RES CAUSNG
The system designer can connect the

MID-16 or CZM-4 inputs to another system
via a relay or have a remote reset input.
When this input changes state to the offnormal position, the MXL-IQ resets in the
same way as a RED KEY reset. Existing
events do not need to be acknowledged
and audibles do not need to be silenced.
NOTE:
This option is limited to NFPA 72A systems.
In networked systems, the scope of the
reset is local.
ALD Fast Polling

When this option is set in the CSG-M for
the ALD loops, the ALD polls only up to the
last device installed on the loop, thus
speeding up the system response. For
example, if there are only 5 devices installed on the ALD loop, the MXL-IQ polls
only up to address 5 on that loop instead of
polling all 60 addresses.
The ALD Fast Polling option requires
ALD-2I board Revision 14 and SMB ROM
Rev. 6.0. See the CSG-M Appendix for
Revision 10.01, P/N 315-096220, for setting

this option.
NOTE:
The ALD Fast Polling option can only be
used with Non-Fireprint Detectors.
24 Hour Trouble Resound /

Reminder Timer
If this feature is set in CSG-M, the MXL-IQ
automatically sounds the trouble buzzer
every 24 hours from the time that the
trouble was acknowledged until the trouble is
cleared. The troubles themselves are not
re-annunciated.
Trouble Delay Time for Damper Control

Using TRI
This delay time was fixed at 30 seconds in
the previous MXL-IQ Revisions. In Revision
6.0, the MXL-IQ delays the TRI damper
travel delay time trouble according to the
time that is selected in CSG-M. The delay
time is programmable from 0 to 90 seconds
in 1 second increments.
Delay of AC Failure Report

The delay time is programmable in CSG-M
from 0 to 90 seconds in 1 second increments.
The default value for this option is 0 seconds,
which results in an immediate reporting of
the trouble.
If an AC failure occurs, the MXL-IQ checks
the database for the delay time and starts
O-1
Appendix O
the timer if the delay time is other than zero.
No AC failure trouble is reported at this time.
At the end of this delay time, if the AC still
fails, the MXL-IQ posts the AC Failure
trouble; otherwise, it goes back to the
original state.
CCU Pager Interface

A new selection is added to the list of
printer selections under the Global MKB in
the Network map of the CSG-M: CCU/M
Pager Interface. The new selection
provides a remote interface between the
MXL-IQ panel and the operator.
This selection is available in all situations
where a printer was previously available.
For a 72 Proprietary networked system
(72D system), this selection is available
under a Display Only Global MKB. There
are only two selections in this configuration:
NONE and CCU/M.
O-2
When programmed into the CSG-M, this

pager interface can be either supervised or
unsupervised. The CCU/M interface is an
application specific output device, and not a
global MKB printer for a 72D system. Therefore, if it is installed on a 72D networked
system, it does not satisfy the compile
check for a supervised printer. To pass this
compile error, add a supervised printer to a
local MKB in every node in a 72D system.
Despite the above limitation, in both 72A
and 72D systems the CCU/M interface
counts as one GMKB printer available in a
networked system.
Only the normal print messages for events
are sent to the CCU/M interface. Information such as acknowledge, reset, time
changes, etc., do not output. The output
formatting is considered as a generic ASCII
printer.
Index
A
Acknowledge menu. See Menu: Acknowledge
addresses, 3 - 1
fixed addresses, 3 - 1
CRM-4
connections and ratings, 7 - 5
description, 1 - 9
installation, 2 - 14
module address, 3 - 2
CSM-4
connections and ratings
NFPA 12A, NFPA 1 - 1 and NFPA 2001, 7 - 9
alarm verification, E - 1 to E - 2
NFPA 72 Local, 7 - 7
ALD fast polling. See new features - rev.6.0 and higher
NFPA 72 Municipal Tie, 7 - 8
ALD-2I
description, 1 - 10
analog loop, 1 - 1
analog voltages. See device analog voltages
NFPA 72 Remote Station, 7 - 8

description, 1 - 8
CZM-1B6
analog loops, 7 - 14
application specific detection, I - 1 to I - 2
initiating devices, 7 - 13
ASD. See application specific detection
B
battery calculations, C - 1
BP-61 batteries
description, 1 - 7
BTX batteries
description, 1 - 7
power, 7 - 15
description, 1 - 14
CZM-4
description, 1 - 9
C
Canadian two stage alarm, L - 1 to L - 7
CCU pager interface. See new features - rev.6.0 and
higher
CMI-300
description, 1 - 9
compatible devices, A - 1
delay of AC failure report. See new features - rev.6.0

and higher
device analog voltages, B - 1
devices, compatible. See compatible devices
DI Series of detectors
description, 1 - 15
DT-11
description, 1 - 15
dual criteria logic, M - 1 to M - 3
Index - 1
Index
IEC. See Envirolink
E
Envirolink, F - 1 to F - 3
ILI Series of detectors

description, 1 - 13
ILP Series of detectors
F
FP Series of detectors
description, 1 - 12
description, 1 - 13
ILT
description, 1 - 13
History Log
display, 6 - 6 to 6 - 10
audible silenced event, 6 - 8
audible unsilenced event, 6 - 8
auto sensitivity set event, 6 - 9
block acknowledge event, 6 - 7
configuration changed event, 6 - 9
event, 6 - 6
formats, 6 - 6
manual sensitivity set event, 6 - 9
override event, 6 - 8
password event, 6 - 8
reset event, 6 - 6
set time event, 6 - 7
download formats, 6 - 13
sequence, 6 - 14
local log query, 6 - 5
logging methods, 6 - 2 to 6 - 4
options, 6 - 1
enable, disable and erase, 6 - 4
overview, 6 - 1
print formats, 6 - 10 to 6 - 13
latching/non-latching troubles, G - 1
LIM-1
description, 1 - 14
M
Menu. See MKB-4: operation
Acknowledge, 3 - 18
Alarm, 3 - 18 to 3 - 19
Security, 3 - 21 to 3 - 22
Supervisory, 3 - 19 to 3 - 20
Trouble, 3 - 20 to 3 - 21
Control, 3 - 36 to 3 - 42
Analaser, 3 - 40
Arm/dis, 3 - 38
Change Apps, 3 - 42
Loop Arm, 3 - 39
Loop Disarm, 3 - 39 to 3 - 40
Net Link Request, 3 - 40
Output on/off, 3 - 38 to 3 - 39
Percent/ft, 3 - 41 to 3 - 42
Reset, 3 - 37
Sensitivity, 3 - 37
List, 3 - 22 to 3 - 36
I
ICP / ICP-B6
description, 1 - 12
ID Series of detectors
description, 1 - 12 to 1 - 13
Index - 2
Alarm, 3 - 23 to 3 - 24
Analaser, 3 - 32 to 3 - 34
ASD_apps, 3 - 35 to 3 - 36
Device Type, 3 - 29
Device Usages, 3 - 31 to 3 - 32
Index
Message, 3 - 29 to 3 - 30
global operation, 3 - 12 to 3 - 14
Module, 3 - 28 to 3 - 29
display format, 3 - 12
Node Address, 3 - 32
keypad, 3 - 13 to 3 - 14
Output States, 3 - 31
limitations and restrictions, 3 - 12
Percent/ft, 3 - 34 to 3 - 35
installation, 2 - 4
Security, 3 - 25 to 3 - 26
local operation, 3 - 3
Sensitivity, 3 - 26
alarm, 3 - 6 to 3 - 8
Software Version, 3 - 30 to 3 - 31
command keypad, 3 - 5
Status, 3 - 23
display, 3 - 3
Supervisory, 3 - 24
display keys, 3 - 5
Temp, 3 - 28
internal audible, 3 - 4
Trouble, 3 - 24 to 3 - 25
LEDs, 3 - 5
Voltages, 3 - 26 to 3 - 28
modes of operation, 3 - 5
Test, 3 - 42 to 3 - 49
numeric keypad, 3 - 4
ASD_Devices, 3 - 48
security, 3 - 10 to 3 - 11
Det_cleaned, 3 - 47
special (alt + function) keypad, 3 - 5
Device LED, 3 - 45
supervisories, 3 - 8 to 3 - 9
Event Log, 3 - 47
troubles, 3 - 9 to 3 - 10
Ground Fault, 3 - 44
using the menu, 3-14
Lamp Test, 3 - 45
walktest. See Walktest: operating instructions
Manual Activate, 3 - 49
MOI Lamp Test, 3 - 46
MOD-16
Override, 3 - 46 to 3 - 47
Power, 3 - 44 to 3 - 45
description, 1 - 10
Pre-alarm, 3 - 47 to 3 - 48
installation, 2 - 9
Pyro-diags, 3 - 47
operation, 3 - 3
Set Time, 3 - 43 to 3 - 44
Module Addresses. See Addresses
Summarize, 3 - 48 to 3 - 49
MOI-7
Test Network (X-Net, M-Net), 3 - 46
Menu overview, 3 - 15
description, 1 - 10
MID-16
installation, 2 - 9
description, 1 - 11
operation, 3 - 3
installation, 2 - 9
MKB-4
description, 1 - 5
MOM-2
description, 1 - 8
installation, 2 - 6 to 2 - 9
Index - 3
Index
MOM-4
description, 1 - 8
P
PAL-1
description, 1 - 6
MPS-6/-6W, MPS-12/-12W
description, 1 - 5
MSE-3L
installation, 2 - 2
MSI Series of manual stations
description, 1 - 14
installation, 2 - 6
PBA-1191
description, 1 - 15
PE Series of detectors
description, 1 - 15
percent per foot obscuration, M - 1 to M - 3
PIM-1
description, 1 - 6
MXL Power Supply Load Calculations, D - 1

MXL-IQ
basic components, 1 - 4
battery calculations, C - 1
description, 1 - 1
minimum configuration, 1 - 3
new features - rev.6.0 and higher, O - 1
power supply load calculations, D - 1
software, 1 - 1
N
new features - rev.6.0 and higher, O - 1 to O - 2
installation, 2 - 5
PIM-2/PAL-1
installation, 2 - 6
power limited wiring, K - 1
power supply load calculations, D - 1
pre-alarm, M - 1 to M - 3
R
reset causing zone for MID-16 or CZM-4. See new
features - rev.6.0 and higher: reset causing zone
reset procedures
hard reset, 3 - 11
24 hour trouble resound /reminder timer, O - 1

ALD fast polling, O - 1
CCU pager interface, O - 2
delay of AC failure report, O - 1 to O - 2
reset causing zone, O - 1
trouble delay time for damper control using TRI, O - 1
NIM-1R
connections and ratings, 7 - 29 to 7 - 32
AnaLaser interface, 7 - 32
foreign system interface (FSI), 7 - 31
soft reset, 3 - 11 to 3 - 12
S
security point, installing, H - 1
self restoring troubles. See latching/non-latching
troubles
Silent Knight Model 5128/5129
SMB-2
network, 7 - 29
field wiring, 7 - 36 to 7 - 38
network command center (NCC), 7 - 30
internal wiring, 7 - 35
description, 1 - 11
description, 1 - 4
installation, 2 - 3
module address 3 - 2
Index - 4
Index
spare parts list, N - 1
start up procedure, 2 - 10 to 2 - 16
system operation, global, 3 - 12 to 3 - 14
system test, 4 - 1
T
testing procedures, 4 - 1
TRI Series of interface modules
description, 1 - 14
trouble delay time for damper control using TRI. See
new features - rev.6.0 and higher
trouble messages, J - 1 to J - 8
trouble resound / reminder timer. See new features rev.6.0 and higher
Troubleshooting Guide, 4 - 2
TSW-2
description, 1 - 6
installation, 2 - 2
two stage alarm, Canadian, L - 1 to L - 7
W
Walktest, 5 - 1 to 5 - 6
operating instructions, 5 - 4
overview, 5 - 1
suggested procedure, 5 - 2 to 5 - 3
Index - 5
Index
Index - 6
WARNING:
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance
with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to
Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a
commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever measures may be required to correct the interference.

8 Fernwood Road
P/N 315-093624CD-9

NOTES:
1. For Installation Instructions for the MXL-IQ modules refer
to the Table below.
2. Waterflow Alarm must be AccuLINK (CSG-M) configured
to at least one non-silenceable NAC.
3. Refer to the MXL-IQ OPERATION, INSTALLATION,
AND MAINTENANCE MANUAL (P/N 315-093624) for
minimum NFPA configurations and additional information.
4. Use the following batteries: BTX-1, BTX-2, or BP-61.
5. The CSM-4 module is capable of the following functions:
Leased Line Circuit
Supervised Local Energy Auxiliary Trip (Municipal Tie)
Supervised Notification Appliance Circuit
Releasing Service
6. CRM-4 relay coils are supervised when not energized;
contacts are not.
7. For alternate configurations using CZM-1/1B6s, consult
Technical Support.
8. Optional transient suppressors Model CP2341 and
CP2297 may be used in addition to the transient
protection incorporated in the panel and not in lieu of
that protection. Use them for extreme lightning
conditions. For CP2297 refer to instructions P/N 315-092355.
For CP2341 refer to instructions P/N 315- 092390.
9. For the Silent Knight 5128/5129 Central Station, Remote
Station connection (NFPA 72), refer to instructions P/N
315-093294.
10. The modules indicated with an asterisk in the Table below
are rated power limited on all terminals. Refer to the
MXL-IQ Power Limited Wiring Instructions, P/N 315-095445,
for separation of power limited wiring.
11. When the CSM-4 is configured for Municipal Tie or
Releasing Service, terminals 1 and 4 and/or terminals 9
and 12 are non-power limited. In all other applications, the
CSM-4 is power limited on all terminals.
12. For a list of Compatible Notification Appliances, refer
to P/N 315-096363.
> * 7 (2 =. ', 2 <
:) 0 2 ?
$ . - ( " ? 7 (+ 0- 1(
)( C%+B 44A' A@?
)( C%+B 44A' A@?
/(( OLAE A@? NHML "% 2FKHFE JFIHGFED

8( OLAE A@? NHML "&<;. 2FKHFE JFIHGFED
>&A#@ C:B $,,7
#0C SRQHPMFKFJ ;=1B /#A' A@?
#0C SRQHPMFKFJ ;=1B /T8' A@?
) OLAE A@?
>&A#@
BI&#GHGAF E,D(2
#0C SRQHPMFKFJ ;=1B

/' A@?
#0C SRQHPMFKFJ ;=1B

/' A@?
0 OLAE A@?! V/( +3*$/</54E A@?U
:$J#@"
)( C%+B 4(A' A@?
)( C%+B 4(A' A@?
/(( OLAE A@? NHML "% 2FKHFE JFIHGFED

8( OLAE A@? NHML "&<;. 2FKHFE JFIHGFED
BI&#K
#($#0T8 C%+
0A' A@?
#0T8 C%+ A@?

/9(A' A@?
,( OLAE A@?
BI&#GHGAF
/9$#0T8 C%+
0A' A@?
#0T8 C%+ A@?

08A' A@?
)8 OLAE A@?
>&A#@
:-0),3 $,,7
B>&#K C:B $,,7
#0C SRQHPMFKFJ ;=1B

/#A' A@?
#0C SRQHPMFKFJ ;=1B

##($)#(A' VAOAFRM@KWU
##T8 OLAE A@? VHRGPSJHRX PO@JU
B>&#K
$(0'(+ $.-(
#0C SRQHPMFKFJ ;=1B

)$-A' A@?
#0C SRQHPMFKFJ ;=1B

)$-A' A@?
#T86 OLAE
VHRGPSJFE PHRF @RJ PO@JU
#0 C%+
/#A' A@?
#0 C%+
9((A' A@?
) OLAE A@?
B>&#K
4()(0'.-3 >(2=.1(
*See Note 7
&%$#"!
&,+*)('
"-'/0))0/.,"-'/2*1/.,-'
'&%$#"!
+*"$)((!
+.##-,
+.#)0/
+1*$0
+2*$0
+3*$/!
+3*$/54!
+3*$0!
"+.!
"+.$54!
&"*$/!
*"%$/4
*65$0
*7%$/4
)/8$(-/040$8
)/8$(-/#8-$8
)/8$(-#)88$#
)/8$(-#-)($#
)/8$(-(98)+
)/8$(-(980$)/8$(-(,#8$9
)/8$(-8)88$#
)/8$(-(,#4$,
)/8$(-#0,0$4
)/8$(-8)(4$#
)/8$(-#/)8$8
)/8$(-/94($#
)/8$(-)8,8$)
)/8$(-(9)($0
*7"$,!
*7*$#
*7*$0
*.2$4
*.2$/#
:"*$/1
.'&$/
."*$/!
."*$#
.2$8'
.2$8:,!
1++$/</;
2*5$#
>2=$#
)/8$(-#,--$#
)/8$(-#,,,$8
)/8$(-(98#$,
)/8$(-())0$)
)/8$(-#()($)
)/8$(-#-8)$0
)/8$(-#0(9$8
)/8$(-/04#$/(
)/8$(-#0(9$8
)/8$(-#)4,$0
)/8$(-#,#-$4
)/8$(-8)40$#
)/8$(-8-)/$#
)/8$(-#0))$#
See Note 11
;=1 Y ;SPP =@IF 1FGMHQHFJ
C o mp a tib le In itia tin g D e v ic e s fo r

AL D - 2 I a n d S M B - 2
Compatible
Devices
Base
Installation
Instructions
CZM-1
315-090725-8
CZM-1B6
315-095355-2
DB-11, DB-X11RS
DB-3S + DB-ADPT
DB-X3RS + DB-ADPT
ADBI-60 + DB-ADPT
315-095921-4
315-095921-4
315-095921-4
315-095921-4
FP-11*
FP-11*(d)
AD-11P/11XPR
315-095659-2
DB-11, DB-X11RS
DB-3S + DB-ADPT
DB-X3RS + DB-ADPT
ADBI-60 + DB-ADPT
315-095921-4
315-095921-4
315-095921-4
315-095921-4
DB-3S, DB-X3RS
315-090287-2
AD-3I
AD-3XRI
315-093234-4
315-093235-4
ILI-1/1H/1A/1AH
DB-3S, DB-X3RS
315-095387-1
ILP-1
DB-3S, DB-X3RS
315-092594-5
AD-3ILP
AD-3XRILP
315-093234-4
315-093235-4
ILPT-1
DB-3S, DB-X3RS
ILP-2**
FPT-11*
ID-60I/IH/IA/IAH
"-'/0))0/.,"-'/2*1/.,-'
ILP-1 (d)
ILP-2**(d)
ILT-1
For Proprietary Burglary Application (1076) use a

TSW-2 tamper switch to monitor the main enclosure.
Monitor each TRI-60/60R/60D or TRI-B6/B6R/B6D
related to this application (1076) for 24 hours by a
listed motion detector to prevent tampering.
C ompatible D etectors for C ZM -4

Detector
Base
C ompatible D etectors for C ZM -1/ -1B 6*
Installation Instructions
DI-3/3H*
DB-3S
315-081943-15
315-092594-5
DI-A3/A3H*
DB-3S
315-081943-15
DI-3/3H
DB-3S
315-081943-15
DB-3S, DB-X3RS
315-095028-3
DI-B3/B3H*
DB-3S
315-081943-15
315-093234-4
315-093235-4
315-093234-4
315-086591-7
DI-A3/A3H
AD-3ILP
AD-3XRILP
AD-3I/3ILP
AD-3RI/3RP
DT-11*
DB-11
DB-3S + DB-ADPT
315-095429-1
315-095429-1
DI-B3/B3H
AD-3I/3ILP
AD-3RI/3RP
315-093234-4
315-086591-7
PBA-1191**
PBB-1191
315-095424-2
DB-11
DB-3S + DB-ADPT
315-095429-1
315-095429-1
PE-3/3T*
DB-3S
AD-3ILP
AD-3RP
315-090875-6
315-093234-4
315-086591-7
PE-3/3T
DB-3S
AD-3ILP
AD-3RP
315-090875-6
315-093234-4
315-086591-7
DB-11
DB-3S + DB-ADPT
AD-11P/11PR
315-094198-6
315-094198-6
315-095659-2
PE-11/11T
DB-11
DB-3S + DB-ADPT
AD-11P
315-094198-6
315-094198-6
315-095659-2
DB-3S, DB-X3RS
315-093336-1
MSI-10/-20
315-090903-3
MSI-10B/-20B
315-093329-3
MSI-B6F
315-095302-1
MSI-MB6
315-093613-1
TRI-B6/B6D/B6R
315-093315-3
TRI-B6M
315-094547-1
TRI-S/D/R
315-096242-1
*The FP-11 is only com pat ible w it h M XL-I Q R ev. 6. 0 or

great er f irm w are.
**The I LP-2 i s onl y com pat i bl e wi t h M XL-I Q Rev. 3. 0 or
great er f i rm ware.
When t he CSG-M i s conf i gured, t he DUCT appl i cat i on
m ust be sel ect ed when t he devi ce i s used i n an ai r duct
housi ng or i n a spot duct appl i cat i on.
CONNECTION DIAGRAM
) OLAE A@?
#0C SRQHPMFKFJ ;=1B /#A' A@? #0C SRQHPMFKFJ ;=1B /T8A' A@?
B>&#K
&*-.1.70) L.(
ID-60IB/IBH
&%$#"!
&,+*)('
CERBERUS PYROTRONICS Model MXL-IQ
5 ) ( 1 / 2 . 1 0 ) 40 / . - 3 '
;:) ) 20/. -3' 02( 7(2 9,-(8 7(2 ) ,,78 ,2 7(2 1. 21*. /6
PE-11/11T*
*M ay use up t o 30 det ect ors of any t ype.

**Onl y one PBA-1191, and no addi t i onal devi ces, can be
connect ed t o a CZM -4 i ni t i at i ng zone.
Detector
DT-11
Base
Installation Instructions
M a y u s e u p t o 1 5 d e t e c t o rs o f a n y t y p e .
*D o n o t u s e A D - 1 1 P R o r d e t e c t o r - o p e r a t e d a c c e s s o r i e s w i t h t h e
C Z M -1 / -1 B 6 .

8 Fernwood Road
P/N 575-293638CD-9

Siemens MXL IQ Operation Installation Manual

Uploaded by

Copyright:

Available Formats

Siemens MXL IQ Operation Installation Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Siemens MXL IQ Operation Installation Manual

Uploaded by

Copyright:

Available Formats

What are the different ways to navigate through the manual?

What are the different ways to navigate through the manual?

What are the different ways to change the page view?

What are the different ways to change the page view?

Technical Manuals Online! - http://www.tech-man.

This CD-Rom contains

MXL/MXLV Control Panel

MXL-IQ Control Panel

MXL-IQ CONTROL PANEL

Siemens Building Technologies, Inc.

Siemens Building Technologies, Ltd.

Technical Manuals Online! - http://www.tech-man.com

Components Of The Basic System __________________________________ 1 - 4

Optional Modules _______________________________________________ 1 - 7

Technical Manuals Online! - http://www.tech-man.com

Intelligent/Analog Devices _______________________________________ 1 - 12

Conventional Devices ___________________________________________ 1 - 15

Installation Instructions For The MXL-IQ Control Panel __________________ 2 - 2

Technical Manuals Online! - http://www.tech-man.com

Start Up Procedure ____________________________________________ 2 - 10

Using The MKB-4 Keyboard/Annunciator Panel In Local Mode ____________ 3 - 3

Technical Manuals Online! - http://www.tech-man.com

Reset Procedures ______________________________________________ 3 - 11

Using The MKB Keyboard/Annunciator Panel in Global Mode ____________ 3 - 12

Using The Menu _______________________________________________ 3 - 14

ACKNOWLEDGE Menu __________________________________________ 3 - 18

Technical Manuals Online! - http://www.tech-man.com

LIST Menu ____________________________________________________ 3 - 22

CONTROL Menu _______________________________________________ 3 - 36

Technical Manuals Online! - http://www.tech-man.com

Control Output on/off ___________________________________________ 3 - 38

TEST Menu ___________________________________________________ 3 - 42

Testing and Troubleshooting _________________ 4 - 1

Technical Manuals Online! - http://www.tech-man.com

Walktest Operating Instructions______________ 5 - 1

Suggested Walktest Proedure _____________________________________ 5 - 2

History Log ______________________________ 6 - 1

CSG-M History Options__________________________________________ 6 - 1

Logging Methods _______________________________________________ 6 - 2

Technical Manuals Online! - http://www.tech-man.com

Audible Silenced Event __________________________________________ 6 - 8

Connections and Ratings ___________________ 7 - 1

Technical Manuals Online! - http://www.tech-man.com

Compatible Devices _____________________________________________ A - 1

Device Analog Voltages __________________________________________ B - 1

Technical Manuals Online! - http://www.tech-man.com

Technical Manuals Online! - http://www.tech-man.com

To ensure reliable operation, the MXL-IQ

All modules are continuously supervised for

Technical Manuals Online! - http://www.tech-man.com

fied modules. Any modules or devices that

Minimum MXL-IQ Control Panel

Table 1 presents the minimum configuration necessary to meet NFPA 72 Local,

The MXL-IQ System polls all network

NFPA Minimum Quantity

MXL-IQ Main Unit

Optional Module Card Cage

Optional Module Card Cage

Conventional Zone Module

Analog Loop Driver