Ventilation

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 7

ECM 3033 (L)

BUILDING SERVICES LABORATORY REPORT

TOPIC

VENTILATION

PROGRAMME

EV101

SEMESTER
GROUP MEMBERS

05
1
2
3
4
5

LECTURER

SECTION

03

ADIB AZALI BIN SALLEH


MUHAMMAD AMIRUL ASYRAF
BIN MOHD RANI
AIN NUR AISHAH BT MOHD
YUSOF
ANISAH FARHAH BINTI AHMAD
AMELIA BT ABD KARIM

DATE

21/10/2016

PTM140709051
PTM140708516
PTM140708669
PTM140708619
PTM140708636

SIR IZAMUDIN BIN MOHAMED

TABLE OF CONTENT

NO
1
2
3
4
5
6
7

CONTENTS
INTRODUCTION
OBJECTIVES
APPARATUS
DISCUSSION
CONCLUSION
REFERENCES
APPENDIX

PAGES
3
3
4-5
6
6
6
7

1.0 INTRODUCTION

Ventilation primarily takes two forms natural and mechanical. Natural ventilation is the process
of fresh air entering a building via a window, door or other opening while mechanical ventilation
is air that is drawn into the building using machinery (typically fans).
Good ventilation is essential to human wellbeing; the provision of fresh air in replacement of
stale air maintains the correct levels of oxygen and carbon dioxide in the air, and removes
odours, bacteria, excess heat and other atmospheric contaminants. It also prevents
condensation, which is caused by excess humidity. The capability of a ventilation system for an
individual room is usually measured according to how many changes of air it is capable of per
hour, that is how many times all the air in the room can be completely replaced. The amount of
ventilation required varies considerably depending on what the space is used for; an office will
typically need far fewer changes of air than a kitchen or factory.

2.0 OBJECTIVE
To control indoor air quality. Excess humidity, odours, and contaminants can often be
controlled via dilution or replacement with outside air.
To know the type of ventilation and how the process begin.

3.0 APPARATUS

Figure 1.1 Ventilation Trainer B500

Figure 1.3 Variable speed controller

Figure 1.2 Pitot tube

Figure 1.4 Centrifugal fan

Figure 1.5 Activated carbon air filter

Figure 1.6 Bag filter

4.0 DISCUSSION
A ventilation system is a mechanical structure of connected devices that controls airflow within
confined spaces, commonly homes and offices. Its main function is to introduce a constant
supply of fresh air, usually from the outside while channeling stale air back out. Fans and pumps
are common parts of these systems, as are vent grates and air flow tunnels. In most cases, the
major working parts are all built within the walls and ducts of structures. People using the space
do not usually see any of the working pieces.

5.0 CONCLUSION
The simplicity of the system design must be weighed up against the fact that air requirements
may not be ideally accommodated. The total investment costs for the entire system are only
slightly less than for a fully variably controlled system, but the energy costs (for heating and
cooling of the supply and exhaust air) are very high. The decision in favor of fully variable
systems is obvious, because such systems are amortized within 1 to 2 years due to the savings
potential of the lower energy and construction costs Lower energy requirements reduce the
operating costs and preserve the environment. Lastly, the ventilation is low energy requirement
and operating cost but for the first operation to put ventilation take a high costs.

6.0 REFERENCE
http://www.bestech.com.au/wp-content/uploads/B500_V3.pdf
http://www.p-a-hilton.co.uk/products/B500-Ventilation-Trainer
http://www.solution.com.my/pdf/FM801(A4).pdf

7.0 APPENDIX
6

Figure 1.1The students were focusing to the briefing.

Figure 1.2 Sir Quddus gives a briefing about the experiment.

Figure 1.3 Ain is reading the manual handling of the machine.

You might also like