Product data sheet

Characteristics

ATV630D11N4

variable speed drive ATV630 - 11kW/15HP 380...480V - IP21/UL type 1

Aug 12, 2016

range of product

Altivar Process ATV600

product or component
type

Variable speed drive

product specific application

Process and utilities

device short name

ATV630

variant

Standard version

product destination

Synchronous motors
Asynchronous motors

mounting mode

Wall mount

EMC filter

Integrated conforming to EN/IEC 61800-3 category

C2 with 50 m motor cable maxi
Integrated conforming to EN/IEC 61800-3 category
C3 with 150 m motor cable maxi

IP degree of protection

IP21 conforming to IEC 60529

IP21 conforming to IEC 61800-5-1

degree of protection

UL type 1 conforming to UL 508C

type of cooling

Forced convection

supply frequency

50...60 Hz (- 5...5 %)

network number of
phases

3 phases

[Us] rated supply voltage

380...480 V (- 15...10 %)

motor power kW

11 kW (normal duty)
7.5 kW (heavy duty)

motor power hp

15 hp (normal duty)
10 hp (heavy duty)

line current

14.1 A at 380 V (heavy duty)

17 A at 480 V (normal duty)
19.8 A at 380 V (normal duty)
12.5 A at 480 V (heavy duty)

prospective line Isc

50 kA

apparent power

14.1 kVA at 480 V (normal duty)

10.4 kVA at 480 V (heavy duty)

continuous output current

23.5 A at 4 kHz (normal duty)

16.5 A at 4 kHz (heavy duty)

maximum transient current

24.8 A during 60 s (heavy duty)

25.9 A during 60 s (normal duty)

asynchronous motor
control profile

Constant torque standard

Variable torque standard
Optimized torque mode

synchronous motor control profile

Permanent magnet motor

output frequency

0.0001...0.5 kHz

nominal switching frequency

4 kHz

switching frequency

4...12 kHz with derating factor

2...12 kHz adjustable

safety function

STO (safe torque off) SIL 3

discrete input logic

16 preset speeds

The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.

Main

communication port protocol

Ethernet
Modbus serial
Modbus TCP

option card

Slot A : communication module for CANopen SUBD9

Slot A : communication module for Ethernet IP/Modbus TCP/MD-Link
Slot A : communication module for DeviceNet
Slot A : communication module for CANopen daisy
chain RJ45
Slot A/slot B : digital and analog I/O extension module
Slot A : communication module for Modbus TCP/
EtherNet/IP
Slot A/slot B : output relay extension module
Slot A : communication module for Profibus DP V1
Slot A : communication module for CANopen screw
terminals
Slot A : communication module for Profinet

Complementary
output voltage

<= power supply voltage

permissible temporary current boost

1.1 x In for 60 s (normal duty)

1.5 x In for 60 s (heavy duty)

motor slip compensation

Automatic whatever the load

Can be suppressed
Adjustable
Not available in permanent magnet motor law

acceleration and deceleration ramps

Linear adjustable separately from 0.01 to 9000 s

S, U or customized

braking to standstill

By DC injection

protection type

Drive : line supply phase loss

Motor : safe torque off
Drive : overspeed
Drive : overload of output voltage
Drive : overheating
Drive : break on the control circuit
Drive : overcurrent between output phases and earth
Drive : short-circuit protection
Drive : safe torque off
Motor : thermal protection
Drive : motor phase break
Drive : line supply undervoltage
Drive : thermal protection
Motor : motor phase break
Drive : overvoltages on the DC bus
Drive : line supply overvoltage

frequency resolution

Display unit : 0.1 Hz

Analog input : 0.012/50 Hz

electrical connection

Line side : screw terminal 6 mm (AWG 10)

Control : removable screw terminals 0.5...1.5 mm (AWG 20...AWG 16)
Motor : screw terminal 6...10 mm (AWG 10...AWG 8)

type of connector

RJ45 (on the remote graphic terminal) for Ethernet/Modbus TCP

RJ45 (on the remote graphic terminal) for Modbus serial

physical interface

2-wire RS 485 for Modbus serial

transmission frame

RTU for Modbus serial

transmission rate

10/100 Mbit/s for Ethernet IP/Modbus TCP

4.8, 9.6, 19.2, 38.4 kbit/s for Modbus serial

exchange mode

Half duplex, full duplex, autonegotiation for Ethernet/Modbus TCP

data format

8 bits, configurable odd, even or no parity for Modbus serial

type of polarization

No impedance for Modbus serial

number of addresses

1...247 for Modbus serial

method of access

Slave for Modbus TCP

supply

Internal supply for reference potentiometer (1 to 10 kOhm) : 10.5 V DC +/- 5 %

current <= 10 mA (overload and short-circuit protection)
Internal supply for digital inputs and STO : 24 V DC (21...27 V) current <= 200
mA (overload and short-circuit protection)
External supply for digital inputs : 24 V DC (19...30 V) current <= 1.25 mA (overload and short-circuit protection)

local signalling

3 LEDs dual colour for embedded communication status

3 LEDs for local diagnostic
1 LED red for presence of voltage
4 LEDs dual colour for communication module status

width

171 mm

height

409 mm

depth

233 mm

product weight

7.7 kg

analogue input number

analogue input type

Software-configurable voltage AI1, AI2, AI3 : 0...10 V DC impedance 30 kOhm,

resolution 12 bits
Software-configurable current AI1, AI2, AI3 : 0...20 mA impedance 250 Ohm, resolution 12 bits

discrete input number

discrete input type

Programmable DI1...DI6 : 24 V DC <= 30 V impedance 3.5 kOhm

Programmable as pulse input DI5, DI6 0...30 kHz : 24 V DC <= 30 V
Safe torque off STOA, STOB : 24 V DC <= 30 V impedance > 2.2 kOhm

input compatibility

Discrete input DI1...DI6 : level 1 PLC conforming to EN/IEC 61131-2

Discrete input DI5, DI6 : level 1 PLC conforming to IEC 65A-68
Discrete input STOA, STOB : level 1 PLC conforming to EN/IEC 61131-2

discrete input logic

STOA, STOB, positive logic (source) : , < 5 V (state 0), > 11 V (state 1)
DI5, DI6, positive logic (source) : , < 0.6 V (state 0), > 2.5 V (state 1)
DI1...DI6, positive logic (source) : , < 5 V (state 0), > 11 V (state 1)
DI1...DI6, negative logic (sink) : , > 16 V (state 0), < 10 V (state 1)

analogue output number

analogue output type

Software-configurable current AO1, AO2 : 0...20 mA, resolution 10 bits

Software-configurable voltage AO1, AO2 : 0...10 V DC impedance 470 Ohm, resolution 10 bits

sampling duration

Discrete input DI5, DI6 : 5 ms (+/- 1 ms)

Discrete input DI1...DI4 : 2 ms (+/- 0.5 ms)
Analog output AO1 : 10 ms (+/- 1 ms)
Analog input AI1, AI2, AI3 : 5 ms (+/- 0.1 ms)

accuracy

Analog output AO1, AO2 : +/- 1 % for a temperature variation 60 C

Analog input AI1, AI2, AI3 : +/- 0.6 % for a temperature variation 60 C

linearity error

Analog input AI1, AI2, AI3 : +/- 0.15 % of maximum value

Analog output AO1, AO2 : +/- 0.2 %

relay output number

relay output type

Configurable relay logic R2 : sequence relay NO electrical durability 100000 cycles

Configurable relay logic R3 : sequence relay NO electrical durability 100000 cycles
Configurable relay logic R1 : fault relay NO/NC electrical durability 100000 cycles

refresh time

Relay output R1, R2, R3 : 5 ms (+/- 0.5 ms)

minimum switching current

Relay output R1, R2, R3 : 5 mA at 24 V DC

maximum switching current

Relay output R1, R2, R3 on inductive load (cos phi = 0.4 and L/R = 7 ms) : 2 A at
30 V DC
Relay output R1, R2, R3 on inductive load (cos phi = 0.4 and L/R = 7 ms) : 2 A at
250 V AC
Relay output R1, R2, R3 on resistive load (cos phi = 1) : 3 A at 30 V DC
Relay output R1, R2, R3 on resistive load (cos phi = 1) : 3 A at 250 V AC

isolation

Between power and control terminals

IP degree of protection

IP21

Environment
insulation resistance

> 1 mOhm at 500 V DC for 1 minute to earth

noise level

56 dB conforming to 86/188/EEC

power dissipation in W

255 W (forced convection) at 380 V switching frequency 4 kHz

51 W (natural convection) at 380 V switching frequency 4 kHz

volume of cooling air

103.0 m3/h

operating position

Vertical +/- 10 degree

THDI

<= 48 % from 80...100 % of load conforming to IEC 61000-3-12

electromagnetic compatibility

Radiated radio-frequency electromagnetic field immunity test conforming to IEC

61000-4-3 level 3
1.2/50 s - 8/20 s surge immunity test conforming to IEC 61000-4-5 level 3
Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3
Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3
Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4

pollution degree

2 conforming to EN/IEC 61800-5-1

vibration resistance

1.5 mm peak to peak (f = 2...13 Hz) conforming to IEC 60068-2-6

1 gn (f = 13...200 Hz) conforming to IEC 60068-2-6

shock resistance

15 gn during 11 ms conforming to IEC 60068-2-27

relative humidity

5...95 % without condensation conforming to IEC 60068-2-3

ambient air temperature for operation

50...60 C with derating factor

-15...50 C without derating

ambient air temperature for storage

-40...70 C

operating altitude

<= 1000 m without derating

1000...4800 m with current derating 1 % per 100 m

environmental characteristic

Dust pollution resistance class 3S3 EN/IEC 60721-3-3

Chemical pollution resistance class 3C3 EN/IEC 60721-3-3

standards

IEC 61508
EN/IEC 61800-3
UL 508C
EN/IEC 61800-3 environment 1 category C2
IEC 13849-1
EN/IEC 61800-3 environment 2 category C3
IEC 60721-3
EN/IEC 61800-5-1
IEC 61000-3-12

product certifications

DNV-GL
CSA
ATEX zone 2/22
TV
REACH
UL
ATEX INERIS

marking

CE

Offer Sustainability
Sustainable offer status

Green Premium product

RoHS (date code: YYWW)

Compliant &#xA0;- since&#xA0; 1513 &#xA0;-&#xA0; Schneider Electric declaration of conformity

REACh
Product environmental profile
Product end of life instructions

Schneider Electric declaration of conformity

Reference contains SVHC above the threshold - go to CaP for more details
to CaP for more details
Available

Product Environmental

Available

End Of Life Manual

Go

Product data sheet

Dimensions Drawings

ATV630D11N4

Dimensions
IP21 / UL Type 1 Drives - Front and Left View

Drives without IP21 top cover - Left and Rear View

ATV630D11N4

Product data sheet

Mounting and Clearance

Clearances

X1

X2

X3

100 mm (3.94 in.)

100 mm (3.94 in.)

10 mm (0.39 in.)

Mount the device in a vertical position (10). This is required for cooling the device.
Do not mount the device close to heat sources.
Leave sufficient free space so that the air required for cooling purposes can circulate from the bottom to the top of the drive.

Mounting Types
Mounting Type A: Individual IP21

a = 100 mm (3.94 in.)

Mounting Type B: Side by Side IP20

Product data sheet

Connections and Schema

ATV630D11N4

Single or Three-Phase Power Supply with Upstream Breaking via Line Contactor
Connection diagrams conforming to standards EN 954-1 category 1 and IEC/EN 61508 capacity SIL1, stopping category 0 in accordance
with standard IEC/EN 60204-1

(1) Use digital output R1 set to operating state Fault to switch Off the product once an error is detected.
A1 : Drive
KM1 :Line Contactor
Q2, Circuit breakers
Q3 :
S1, Pushbuttons
S2 :
T1 : Transformer for control part

Single or Three-Phase Power Supply with Downstream Breaking via Switch Disconnector
Connection diagrams conforming to standards EN 954-1 category 1 and IEC/EN 61508 capacity SIL1, stopping category 0 in accordance
with standard IEC/EN 60204-1

(1) Use digital output R1 set to operating state Fault to switch Off the product once an error is detected.
A1 : Drive
Q1 : Switch disconnector

Control Block Wiring Diagram

(1) Safe Torque Off

(2) Analog Output
(3) Digital Input
(4) Reference potentiometer
(5) Analog Input
A1 : ATV6.. Drive
R1A, Fault relay
R1B,
R1C :
R2A, Sequence relay
R2C :
R3A, Sequence relay
R3C :

Sensor Connection
It is possible to connect either 1 or 3 sensors on terminals AI2 or AI3.

Sink / Source Switch Configuration

The switch is used to adapt the operation of the logic inputs to the technology of the programmable controller outputs.
Set the switch to Source (factory setting) if using PLC outputs with PNP transistors.
Set the switch to Ext if using PLC outputs with NPN transistors.

Switch Set to SRC (Source) Position Using the Output Power Supply for the Digital Inputs

Switch Set to SRC (Source) Position and Use of an External Power Supply for the DIs

Switch Set to SK (Sink) Position Using the Output Power Supply for the Digital Inputs

Switch Set to EXT Position Using an External Power Supply for the DIs

10

Product data sheet

Performance Curves

ATV630D11N4

Derating Curves

40 C (104 F) - Mounting type A, B and C

50 C (122 F) - Mounting type A, B and C
60 C (140 F) - Mounting type B and C
In : Nominal Drive Current
SF : Switching Frequency

11