UT 300 R2U with DSL Lamp Type 1

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Advanced setup on the left side.
Tick Remove at the right end of the line having 0/35 as VPI/VCI values.
Click Remove below.
Click Add , A new window will appear. Click Next.
Select PPP over Ethernet and click Next.
Enter PPP Username and PPP Password. click Next.
Click Next. Click Save.
Click Save/Reboot.
Wait till reboot is complete (3 minutes)...

DNA-A211-1 ITI Make Type 4

Open browser. Type 192.168.1.1 in Address bar. click Go

Enter both Username and Password as admin. Click OK.
Wireless Configuration
Click Advanced setup on the left side.
Click Wireless on the left side,Ensure that enable wireless is ticked.
Click Security on the left side. Select WPA-PSK as Authentication type.
Enter Preshared key (8 character alphanumeric password) as wi-fi secret
password.
Click Save below .
WAN Configuration
Click WAN on the left side.
Tick Remove at the right end of the line having 0/35 as VPI/VCI values.
Click Remove below.
Click Add , A new window will appear. Click Next. Select PPP over Ethernet and
click Next.
Enter PPP Username and PPP Password. click Next. Click Next. Click Save.
Click Save/Reboot. Wait till reboot is complete (3 minutes)...If configuration is not
saved, DO NOT click Save/Reboot. Stop after previous step.

WA3002G4 UTStar Make

Open browser. Type 192.168.1.1 in Address bar. click Go.

Enter both Username and Password as admin. Click OK.
Wireless Configuration
Click Advanced setup on the left side.
Click Wireless on the left side. Ensure that Enable Wireless is ticked.
Click Security on the left side. Select WPA-PSK as Authentication type.
Enter Pre-shared key (8 character alphanumeric password) as wi-fi secret
password.
Click Save below.
WAN Configuration
Click WAN on the left side.
Tick Remove at the right end of the line having 0/35 as VPI/VCI values.
Click Remove below.
Click Add , A new window will appear. Click Next.
Select PPP over Ethernet and click Next
Enter PPP Username and PPP Password. click Next. Click Next. Click Save.
Click Save/Reboot. Wait till reboot is complete (3 minutes)...

UT300 R2U with ADSL Lamp UTStar Make

Open browser. Type 192.168.1.1 in Address bar. Click Go. (If you are using USB, type
192.168.1.2. Click Go. )
Enter both Username and Password as admin. Click OK.
click Run wizard. click Next. click Next again.
select PPPoE / PPPoA and click Next
Enter Username and Password. Click Next.
click Restart.
Wait till reboot complete (3 minutes)...

Siemens C 2110 (old) Type OR ZTE ZXDSL811

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Configuration on the left pannel.

Click Internet below.

Click Delete icon (drum symbol) right to 0/35.
Click Add below.
Give VPI as 0 (zero) and VCI as 35. Click Next.
Tick PPP over Ethernet.
Select LLC/SNAP as Encapsulation. Click Next.
Tick Enable NAT and Add default route. Click Next.
Enter PPP Username ,PPP Password and Confirm Password. Click Next. Click Apply.
Click System on the left pannel.
Click Reset and Restart.
Click Restart(Do not tick reset to factory default). Wait for few moments...

Nokia Siemens Networks C 2110 Type 1

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
This procedure is for the modems having Firmware Version V55.1.04.10
To find Firmware Version :
Click Overview on left pannel.See the Firmware Version under System
Information section.
Click Configuration on the left pannel.
Click Internet Connection below.
Click Delete icon (drum symbol) right to 0/35.
Click Add below.
Give VPI as 0 (zero) and VCI as 35. Click Next.
Tick PPP over Ethernet (PPPoE).
Select LLC/SNAP as Encapsulation. Click Next.
Tick Enable NAT and Add default route. Do not change any other field. Click Next.
Enter Service Name as bsnl, Broadband Username ,Password and Confirm Password.
Click Next. Click Apply.
Click Admin on the left pannel.
Click Reboot. Select Reboot From as Last.
Click Reboot. Wait for few moments...

MT 880 & MT 882 Huwaei Make Type 1

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click the + sign left to Home .
Click WAN settings below.
Select PPP as WAN type.
Enter Username and password in the respective fields.
Select Maximum idle time as Always on, if there is such an option. Click Save .

The system will ask for reboot. Tick No, and click OK.
Click DNS on left pannel. Enable DNS and make DNS as 0.0.0.0(both). Click Save .
The system will ask for reboot.TickYes, and click OK
Wait for 3 minutes .

SL2_141 Siemens Make

Open browser. Type 192.168.1.1 in Address bar. click Go

Enter both Username and Password as admin. Click OK.
Click Wireless on the left side,Ensure that enable wireless is ticked
Click Security on the left side.
Wireless Configuration
Select WPA-PSK as Authentication Type.
Enter Preshared key (8 character alphanumeric password) as wi-fi secret
password.
Click Save below .
WAN Configuration
Click WAN on the left side.
Tick Remove at the right end of the line having 0/35 as VPI/VCI values.
Click Remove below.
Click Add. A new window will appear. Click Next.
Select PPP over Ethernet and click Next.
Enter PPP Username and PPP Password. click Next. Click Next again.
Click Save. Click Save/Reboot. Wait till reboot is complete (3 minutes)...

UT 3002 G1 UT STARCOM Make

Open browser. Type 192.168.1.1 in Address bar. click Go.

Enter both Username and Password as admin. Click OK.
WAN Configuration
Click Interface setup on the top.
Select PPPoE (right to Encapsulation).
Enter Username and Password.
Ensure that Encapsulation is PPPoE LLC. Click Save.
Wireless Configuration
Click Wireless on top.
Select WPA-PSK as Authentication type .
Enter Preshared key (8 character alphanumeric password) as wi-fi secret
password.

 Click Save.
Click Maintenance above. Click Sys Restart just below.
Select system restart with current configuration
Click Restart. Wait till reboot is complete (3 minutes)...

MT841 HUAWEI/STERLITE Make

Open browser. Type 192.168.1.1 in Address bar. click Go

Enter both Username and Password as admin. Click OK.
WAN Configuration
Click Connections under Basic.
Click Note (edit) at the right end of the line having 0/35 as VPI/VCI value . Click
Delete at bottom .
Click New. Type VPI/VCI as 0/35.
Enter Username and Password. Click Apply.
Wireless Configuration
Click WLAN under Basic. Select WPA-PSK as WEP method .
Enter WPA-PSK key (8 character alphanumeric password) as wi-fi secret
password. Click Apply.
Click the + sign left to Advanced.
Click DNS below. Enable DNS and make DNS as 0.0.0.0(both).
Click Apply. Click Save all.
Select Restart . click OK. Wait till reboot is complete (3 minutes)...

QUIDWAY1003A HUAWEI/STERLITE Make

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
WAN Configuration
Click Setup on top, then PVC0 on left.
Select PPPoE as Connection Type.
Enter Username and Password. Click Apply.
Wireless Configuration
Click wireless on the left.
Enable AP
Click advanced.
Click wireless security. Select WPA.
Enter PSK string (8 character alphanumeric password) as wi-fi secret password.
Click Apply.

 Click Tools above. Click System Commands.

Click save all. Click Restart. Wait till reboot is complete (3 minutes)...

MT 800 Huwaei/STERLITE Make Type 1

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click ATM settings.
Select PPP as WAN type.
Select PPPoE against PPPoE/PPPoA.
Enter Username and password in the respective fields. Click Apply .
Click Advanced .
Click DNS on left pannel. Enable DNS and make DNS as 0.0.0.0(both).
Click Apply. Click Save All.
SelectSave and Submit.
Select Restart and click Submit. Wait for 3 minutes.

DLB 502 T D-LINK Make Type 1

Open browser. Type 192.168.1.1 in Address bar. click Go.

Enter both Username and Password as admin. Click OK.
Click setup on top.
If you already have a connection named say BSNL or dataone on the left side, select it
and delete.
Now Click New connection on the left.
Give Connection name as BSNL.
Select PPPoE as Connection type
Enter Username and Password as allotted by BSNL in the respective fields.
Enter VPI as 0 and VCI as 35. Click Apply.
Click Tools above. Click System Commands .
Click Save all. Click Restart.
Wait till reboot is complete (3 minutes)...

DLB 802 C D-LINK Make Type 1

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Home on top. Click Quick configuration.
Select Connection Name as BSNL.
Operation mode should be Enabled.
VPI should be 0 and VCI 35.
Encapsulation should be LLC and Bridge must be Enabled.
IGMP must be Disabled and Use DHCP also should be Enabled .
Default Route must be Enabled.
Enter Username and Password as allotted by BSNL in the respective fields.
Use DNS must be Enabled. Click Submit.
Click Admin above. Click Commit and reboot .
Click Commit . Click Reboot.
Wait till reboot is complete (3 minutes)...

I BALL BATON ADSL 2+ Router model-ib-lr6111a

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Advanced Setup. Click WAN .
Add VPI - 0 / VCI - 35. Click Next .
Select Bridging or PPPoE . Click Next .
Enter Username and Password, if PPPoE is selected.
Click Next . Click Save.
Click Next . Click Save and Reboot.
Wait till reboot is complete (3 minutes)...

Zebronics G68100

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Home. Click Quick configuration.
Select Encapsulation as PPPoE-LLC.
Enable Bridge. Enable DHCP.

Enter Username and Password.

Enable Use DNS. Click Submit.
Click Admin on Main menu.
Click Commit & Reboot
Select Reboot from last configuration
Click Reboot.
Wait till reboot is complete (3 minutes)...

Compex MRL21E

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click WAN.
Enter VPI as 0 and VCI as 35. Click Next .
Select Bridge or PPPoE . Click Next .
Enter Username and Password, if PPPoE is selected.
Click Save.
Click Save & Reboot.
Wait till reboot is complete (3 minutes)...

Billion's BiPAC 5200(S)

Open browser. Type 192.168.1.254 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Quick Start. Click Run wizard.
Set your password as admin / admin.
Click Time Zobe. Click Next.
Select Bridge or PPPoE . Click Next .
Enter Username and Password, if PPPoE is selected.
Click Saved Changes.
Click Mainteance in Main Menu
Click Mainteance
Click Current Settings
Click Restart
Wait till reboot is complete (3 minutes)...

LINKSYS ADSL Modem

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Setup. Click Internet Setup.
Click ADSL Settings. Select RFC 2516.
Select Bridge or PPPoE . Click Next .
Enter Username and Password, if PPPoE is selected.
Click Save Settings.
Wait till reboot is complete (3 minutes)...

Beetel 220 BX

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click WAN in Advanced Setup.
Click Remove at the right end of the line having 0/35 as VPI/VCI value. Click Next .
Select PPP over Ethernet. Click Next .
Enter Username and Password. Click Next . Click Next .
Click Save.
Click Save / Reboot.
Wait till reboot is complete (3 minutes)...

ZTE DSL 831A 11

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter both Username and Password as admin. Click OK.
Click Configuration. Click Internet.
Click Delete 0/35. Click Add.
Enter VPI as 0 and VCI as 35. Click Next .
Tick PPP over Ethernet.
Select LLC/SNAP as Encapsulation. Click Next .
Tick Enable NAT and Add Default route. Click Next .
Enter Broadband Username and Password. Click Next .
Click Apply.
Click Reset and Restart.

 Click Restart. (Do not tick reset to factory default)

Wait till reboot is complete (3 minutes)...

NETGEAR Model DG632 ADSL Modem Router

Open browser. Type 192.168.0.1 in Address bar. Click Go.

Enter Username as admin and Password as root. Click OK.
Click Setup Wizard.
Click Basic Router Settings.
Select Bridging or PPPoE.
Enter PPPoE Login Name and Password. if PPPoE is selected. Click Apply.
Enter VPI as 0 and VCI as 35. Click Next .
Select Maintenance. Click Router Settings.
Click Save All and Restart.
Wait till reboot is complete (3 minutes)...

Belkin F5D7230uk4 54Mbps Broadband Wireless Router

Open browser. Type 192.168.2.1 in Address bar. Click Go.

Enter Username as admin and Password as root. Click OK.

Teracom Wi-Fi with 4 Ethernet Modem

Open browser. Type 192.168.1.1 in Address bar. Click Go.

Enter Username as admin and Password as admin. Click OK.
Click Configuration. Click Internet Connection.
Tick the box at the right most end of line having VPI/VCI as 0/35.
Click Delete. Click Add.
Type PVC Name as PPP 0-35, VPI as 0 and VCI as 35.
Select Service Category as UBR with PCR. Click Next .
Select option PPP over Ethernet (PPPoE), Encapsulation Type as LLC/SNAP.
Click Next .
Select Obtain an IP address automatically.
Tick Enable NAT. Tick Add Default Route. Click Next.
Type Service Name as BSNL. Type Broadband User Name, Password and

Confirm Password
Select option Always On. Clik Next. Click Apply. Wait for few moments...
Click Admin. Click Reboot. Select Last in Reboot From field.
Click Reboot. Wait for one minute...