Anybus Wireless Bolt

INSTALLATION GUIDE
SCM-1202-006/SP2139 1.5

ENGLISH

Important User Information

Liability
Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB of any inaccuracies or omissions. The data and illustrations found in this document are
not binding. We, HMS Industrial Networks AB, reserve the right to modify our products in line with
our policy of continuous product development. The information in this document is subject to
change without notice and should not be considered as a commitment by HMS Industrial Networks
AB. HMS Industrial Networks AB assumes no responsibility for any errors that may appear in this
document.
There are many applications of this product. Those responsible for the use of this device must ensure that all the necessary steps have been taken to verify that the applications meet all performance and safety requirements including any applicable laws, regulations, codes, and standards.
HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any
problems that may arise as a result from the use of undocumented features, timing, or functional
side effects found outside the documented scope of this product. The effects caused by any direct
or indirect use of such aspects of the product are undefined, and may include e.g. compatibility issues and stability issues.
The examples and illustrations in this document are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular implementation,
HMS Industrial Networks AB cannot assume responsibility for actual use based on these examples and illustrations.

Intellectual Property Rights

HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the
product described in this document. These intellectual property rights may include patents and
pending patent applications in the USA and other countries.

Trademark Acknowledgements
Anybus is a registered trademark of HMS Industrial Networks AB. All other trademarks are the
property of their respective holders.

Copyright 2016 HMS Industrial Networks AB. All rights reserved.

Anybus Wireless Bolt Installation Guide
SCM-1202-006/SP2139 1.5

Description

3 (16)

Description
Anybus Wireless Bolt provides wireless communication capability over WLAN
and/or Bluetooth to Ethernet, serial and CAN networks.
This document describes how to install Anybus Wireless Bolt and set up a basic
configuration. For additional documentation and technical support, please visit
the Anybus support website www.anybus.com/support.

Installation
Anybus Wireless Bolt should always be mounted vertically (logo facing upwards)
due to the characteristics of the internal antenna.
For optimal reception devices should be placed with a line of sight between them
clear of obstructions. A minimum distance of 50 cm between the devices should
be observed to avoid interference.
Make sure that you have all the necessary information about the capabilities and
restrictions of your local network environment before installing the Anybus Wireless Bolt. Contact your network administrator if in doubt.

Caution
This equipment emits RF energy in the ISM (Industrial, Scientific,
Medical) band. Make sure that all medical devices used in proximity to
this device meet appropriate susceptibility specifications for this type of
RF energy.

This product contains parts that can be damaged by electrostatic

discharge (ESD). Use ESD protective measures to avoid equipment
damage.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Installation

4 (16)

Mechanical Installation
Anybus Wireless Bolt is intended to be mounted on top of a machine or cabinet
through an M50 (50.5 mm) hole using the included sealing ring and nut.
Tightening torque: 5 Nm 10 %
Make sure that the sealing ring is correctly placed in the circular groove
in the top part of the housing before tightening the nut.

All measurements are in mm.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Installation

5 (16)

Connector Pinning

Pin

Name

Description

VIN

Power 930 VDC

GND

Power Ground

DI

Digital input (930 VDC)

DI_GND

Digital input ground

ETN_RD+

Ethernet receive + (white/orange)

ETN_RD-

Ethernet receive - (orange)

ETN_TD-

Ethernet transmit - (green)

ETN_TD+

Ethernet transmit + (white/green)

RS485_B

RS-485 B Line

10

FE/Shield

Functional Earth/Functional Earth and Shield

for serial interface

11

RS232_TXD

RS-232 Transmit

12

RS485_A/RS232_RXD

RS-485 A Line or RS-232 Receive

13

RS232_RTS

RS-232 Request To Send

14

RS232_CTS

RS-232 Clear To Send

15

ISO_5V

Isolated 5 V for serial interface

16

ISO_GND

Isolated Ground for serial interface

17

CAN_L

CAN Low

18

CAN_H

CAN High

RS-232 and RS-485 cannot be used at the same time.

Use termination for RS-485 and CAN when needed.

If using a shielded Ethernet cable the shield must be unconnected.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Installation

6 (16)

Cabling
To make an Ethernet connector cable for the Anybus Wireless Bolt:

1.

Cut off one of the connectors on a standard Cat5e or Cat6 Ethernet cable.

2.

Strip off about 40 mm (1 inch) of the cable jacket and untwist the orange,
orange/white, green and green/white wires. The other wires will not be used.

3.

Strip off about 7 mm ( inch) of the isolation on each wire.

4.

Push the pin spring release next to each socket on the connector and insert
the correct wire end according to Connector Pinning, p. 5.

Connect the wires from the power supply to the connector in the same way as
the Ethernet wiring. Make sure that polarity is not reversed.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Configuration

7 (16)

Configuration
Anybus Wireless Bolt can be configured either by setting individual parameters
in the web interface or by using a pre-configured Easy Config mode.
Advanced configuration can be carried out by issuing AT (Hayes) commands in
the AT Commands tab in the web interface, or over Telnet to port 8080. A list of
the supported AT commands is available at www.anybus.com/support.

The Web Interface

The web interface is accessed by pointing your web browser to the IP address of
the internal web server in Wireless Bolt. The default address is 192.168.0.99.
Most configuration settings are self-explanatory. For detailed information about
each setting, see the Anybus Wireless Bolt User Manual.

The web interface is designed for the latest versions of Internet Explorer,
Chrome, Firefox and Safari. Other browsers may not be supported.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Configuration

8 (16)

Easy Config Modes

Mode

Role

Description

(reserved)

Reset the whole configuration to the factory defaults

Reset the IP settings to the factory defaults

Client

Await automatic discovery and configuration by a device

in Mode 5 (WLAN Access Point) or 6 (Bluetooth NAP)

WLAN AP

Discover and reconfigure devices in Mode 4 as clients

Bluetooth NAP

Discover and reconfigure devices in Mode 4 as clients

Modes 4, 5 and 6 are used in combination to automatically set up a WLAN or

Bluetooth network of Wireless Bolt devices.
When Mode 5 or 6 is set in a device it will start a wireless scan for devices set in
Mode 4. If at least one such device is discovered within 120 seconds (the mode
timeout), the device in Mode 5 or 6 will configure itself as an access point, distribute a connection configuration to the devices in Mode 4, and restart. When the
device in Mode 4 has received the configuration it will automatically restart and
attempt to connect to the access point.
The IP address of a client may be changed by the configuration from the
access point. Active browser sessions could therefore be lost.

Mode Timeout
If no connection is established within 120 seconds the devices will cancel the
Easy Config modes and return to their initial state.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Configuration

9 (16)

Factory Reset
Anybus Wireless Bolt can be reset to the factory default settings using either of
the following methods:

Press and hold the Reset Button for >10 seconds and then release it

Execute Easy Config Mode 2

Issue the AT command AT&F

Factory Default Settings

Network Settings
IP Assignment

Static

IP Address

192.168.0.99

Subnet Mask

255.255.255.0

Default Gateway

192.168.0.99

WLAN Settings
Operating Mode

Client

Channel Bands

2.4 GHz & 5 GHz

Authentication Mode

Open

Channel

Auto

Bluetooth Settings
Operating Mode

PANU (Client)

Local Name

[generated from MAC address]

Security Mode

Disabled

System Settings
Password

[empty]

Setting a secure password for the unit is strongly recommended.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Configuration

10 (16)

Reset Button

The reset button is located on the bottom of the unit next to the connector.

Press and hold the button for >10 seconds and then release it to reset to the
factory default settings when the unit is powered on.

Press and hold the button during startup to enter Recovery Mode.

Recovery Mode
If the web interface cannot be accessed, the unit may be reset by starting in Recovery Mode and reinstalling the firmware using Anybus Firmware Manager II.
For further instructions, please refer to the manual update wizard in Anybus
Firmware Manager II.
Firmware updates should normally be carried out through the web
interface. Recovery Mode should only be used if the Wireless Bolt is
unresponsive and the web interface cannot be accessed.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Configuration

11 (16)

Configuration Examples
For more configuration examples, see the Anybus Wireless Bolt User Manual
available at www.anybus.com/support.
EXAMPLE 1: Setting up a network bridge with Easy Config

This example describes how to connect two Ethernet network segments over
WLAN or Bluetooth using two Wireless Bolts.
1.

Reset both Wireless Bolts to the factory defaults (see Factory Reset).

2.

On Wireless Bolt 1, execute Easy Config Mode 4. This unit will now be discoverable and open for automatic configuration.

3.

On Wireless Bolt 2, execute either Easy Config Mode 5 for WLAN, or 6 for
Bluetooth. This unit should now automatically discover and configure Wireless Bolt 1 as a WLAN or Bluetooth client.

If no connection is established within 120 seconds the Easy Config

modes will be aborted and the units will restart in the previous state.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Configuration

12 (16)

EXAMPLE 2: Accessing a PLC from a handheld device over WLAN

This example describes how to access the web interface of a PLC using a tablet
or smartphone over WLAN.
A: The PLC or network has an active DHCP server
1.

In Network Settings, select IP Assignment: Dynamic (DHCP) and continue to step 3 below.

B: The PLC has a static IP address, no DHCP server on the network

1.

Make sure that the IP addresses of the PLC and the Wireless Bolt are within
the same Ethernet subnet.

2.

In Network Settings, select IP Assignment: Static and enable Internal

DHCP Server.

3.

In WLAN Settings, select Operating Mode Access Point and enter a

unique SSID (network name) for the unit.
Select an Authentication Mode and a WLAN channel if required by your network environment, otherwise leave them at the default settings.

4.

Click on Save and Reboot to restart the Wireless Bolt with the new settings.

5.

In the WLAN configuration of the handheld device, connect to the SSID of

the Wireless Bolt.
You should now be able access the web interface of the PLC by entering its
IP address in the web browser on the handheld device.

Do not enable Internal DHCP Server if there is already a DHCP server

on the network.

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Technical Data

13 (16)

Technical Data

General Specifications
Wired Interface Type

Ethernet

Serial RS-232/485 +
Ethernet

CAN + Ethernet

Order code

AWB2000

AWB2010

AWB2020

Range

Up to 100 meters

Antenna

Built-in

Operating temperature

-40 to +65 C

Weight

81 g

Housing

Plastic (PBT glass-reinforced/PC-ABS)

IP class

IP67 for top (outside of host), IP21 for bottom (inside of host)

Dimensions

Height: 70 mm (95 mm incl. connector, 41 mm outside of host)

Diameter: 70 mm

Mounting

M50 screw and nut (50.5 mm hole required)

Connector

Included plug connector (2 x 9 pin 3.5 mm Phoenix DFMC 1.5/9ST-3.5 push-in spring connection)

Power supply

930 VDC (-5% +20%)

Cranking 12 V (ISO 7637-2:2011 pulse 4)
Polarity reversal protection

Power consumption

0.7 W (idle) 1.7 W (max)

Browser support

Internet Explorer, Firefox, Chrome, Safari (latest stable versions)

Configuration

Built-in web interface / Easy Config Modes / AT commands

Vibration compatibility

Sinosodial vibration test according to IEC 60068-2-6:2007 and with

extra severities; Number of axes: 3 mutually perpendicular (X:Y:Z),
Duration: 10 sweep cycles in each axes, Velocity: 1 oct/min, Mode:
in operation, Frequency: 5500 Hz, Displacement 3.5 mm, Acceleration: 2 G.
Shock test according to IEC 60068-2-27:2008 and with extra severities; Wave shape: half sine, Number of shocks: 3 in each axes,
Mode: In operation, Axes X,Y,Z, Acceleration: 30 m/s2 , Duration:
11 ms

Humidity compatibility

EN 600068-2-78: Damp heat, +40 C, 93 % humidity for 4 days

Certifications

Pending (see Anybus Wireless Bolt Compliance Sheet)

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

Technical Data

14 (16)

Host Communication
Ethernet interface

10/100BASE-T with automatic MDI/MDIX cross-over detection

IP, TCP, UDP, HTTP, LLDP, ARP, DHCP Client/Server, DNS support
PROFINET IO, EtherNet/IP, Modbus-TCP

Serial interface

Isolated RS-232/485 (max. 1 Mbit/s)

CAN interface

Isolated CAN (max. 1 Mbit/s

Digital input

Max 3 m signal cable length

WLAN Specifications
Wireless standards

WLAN 802.11a/b/g/d/e/i/h

Operation modes

Access Point or Client

2.4 GHz channels

111

5 GHz channels

3648 (U-NII-1), 5264 (U-NII-2), 100140 (U-NII-2e)

RF output power

16 dBm

Max number of clients

7 (for access point)

Power consumption

54 mA @ 24 VDC (WLAN interface only)

Net data throughput

Up to 20 Mbit/s

Authentication

WPA-PSK, LEAP, PEAP

Encryption

WEP64/128, WPA, WPA2, TKIP, AES/CCMP

Bluetooth Specifications
Core specification

4.0

Wireless profiles

PAN (PANU & NAP)

Operation modes

Access Point or Client

RF output power

10 dBm

Max number of clients

7 (for access point)

Power consumption

36 mA @ 24 VDC (Bluetooth interface only)

Net data troughput

Up to 1 Mbit/s

Security

Authentication & Authorization, Encryption & Data Protection,

Privacy & Confidentiality, NIST Compliant, FIPS Approved

Anybus Wireless Bolt Installation Guide

SCM-1202-006/SP2139 1.5

This page intentionally left blank

last page

HMS Industrial Networks AB

Box 4126
300 04 Halmstad, Sweden
[email protected]

2016 HMS Industrial Networks AB

SCM-1202-006/SP2139 1.5.1949 / 2016-09-14 17:19