Sensors 2013, 13, 17472-17500; doi:10.

3390/s131217472
OPEN ACCESS

sensors
ISSN 1424-8220
www.mdpi.com/journal/sensors
Review

Data Mining for Wearable Sensors in Health Monitoring

Systems: A Review of Recent Trends and Challenges
Hadi Banaee *, Mobyen Uddin Ahmed and Amy Loutfi

Center for Applied Autonomous Sensor Systems, Orebro

University, SE-70182 Orebro,
Sweden;
E-Mails: [email protected] (M.U.A.); [email protected] (A.L.)
* Author to whom correspondence should be addressed; E-Mail: [email protected];
Tel.: +46-19-30-3415; Fax: +46-19-30-3463.
Received: 20 September 2013; in revised form: 15 November 2013 / Accepted: 6 December 2013 /
Published: 17 December 2013

Abstract: The past few years have witnessed an increase in the development of wearable
sensors for health monitoring systems. This increase has been due to several factors such
as development in sensor technology as well as directed efforts on political and stakeholder
levels to promote projects which address the need for providing new methods for care given
increasing challenges with an aging population. An important aspect of study in such system
is how the data is treated and processed. This paper provides a recent review of the latest
methods and algorithms used to analyze data from wearable sensors used for physiological
monitoring of vital signs in healthcare services. In particular, the paper outlines the more
common data mining tasks that have been applied such as anomaly detection, prediction
and decision making when considering in particular continuous time series measurements.
Moreover, the paper further details the suitability of particular data mining and machine
learning methods used to process the physiological data and provides an overview of the
properties of the data sets used in experimental validation. Finally, based on this literature
review, a number of key challenges have been outlined for data mining methods in health
monitoring systems.
Keywords: data mining; wearable sensors; healthcare; physiological sensors; health
monitoring system; machine learning technique; vital signs; medical informatics

Sensors 2013, 13

17473

1. Introduction
With the increase of healthcare services in non-clinical environments using vital signs provided by
wearable sensors, the need to mine and process the physiological measurements is growing significantly.
Moreover, recent advances in data mining for health monitoring systems have led to provide proactive
information [1]. In the literature much attention has been given to sensor development and architectures
for wearable sensors [25]. Today, there are several reviews on the topic which provide an overview of
the current state of the art [69]. More specifically these reviews contribute with a general and global
overview of wearable sensors and their relevance to biomedicine, medical informatics, and ambient
assisted living (AAL) [1012]. However, as the field progresses and more works consider deployment
in real settings, data mining techniques that consider the specific challenges which emerge from data
coming from wearable sensors is of ever increasing importance. In health monitoring systems focus has
been recently shifting from that of obtaining data to one of developing intelligent algorithms to perform
a variety of the tasks [12]. Such tasks not only include traditional pattern recognition and anomaly
detection but also must consider decision based systems which can handle context awareness, and
subject specific models and personalization. These latter challenges are particularly important if health
monitoring services are to be designed that can address the growing market needs and opportunities in
pervasive sensing such as distributed health monitoring and long-term prevention. This paper attempts
to clarify how certain data mining methods have been applied in the literature. It also attempts to reveal
trends in the selection of the data processing methods based on the requirements of the monitoring
system. For this reason, the paper focuses on reviewing the data mining and pattern recognition
methods used in the literature for applications involving wearable sensing technologies. Focus is put
on the algorithms and data sets that have been used in order to provide an overview of the algorithms
capabilities and shortcomings.
In this review paper we provided a collection of relevant works in this field to cover recently applied
data processing methods on wearable sensor. As the considered area consists both within the computer
science and health or medical science, the range of possible terminologies to consider were wide.
Therefore, some global instances of the investigated keywords in this study are: wearable sensors,
health monitoring, Sensor data mining, physiological time series, healthcare, health informatics, healthy
living and wellbeing, physiological sensors, health monitoring, machine learning technique, vital signs
monitoring, biomedical signal processing, and pattern recognition.
As the literature in this field is vast, we also have limited the scope of this paper to include wearable
sensors that measure health parameters such as vital signs for disease management and prevention health
monitoring systems. Specifically we concentrated the review on the following vital sign parameters:
electrocardiogram (ECG), oxygen saturation (SpO2 ), heart rate (HR), Photoplethysmography (PPG),
blood glucose (BG), respiratory rate (RR), and blood pressure (BP). Also this survey covered the other
synonym terms and specific disease or problems related to the mentioned health parameters. Also for
data analysis part, we combined the mentioned keywords with the particular terms in data mining,
machine learning, pattern recognition and decision support system fields in order to gather the articles
which contain data processing phase. It should be noted that the activity monitoring via accelerometers
such as activity recognition, gait research and rehabilitation is outside of the scope of this review. The

Sensors 2013, 13

17474

following studies [1316] have provided the recent reviews on the topic of human activity monitoring.
Finally, for the sake of investigating the recent trends of research in mentioned area and also eliciting the
potential challenges, the period of the collected papers are filtered to the last four years. So, the selected
papers as the representatives of the performed research are limited to the more than eighty papers.
The paper is organized as follows. In Section 2, we first begin with a brief summary of review works
which are relevant to this survey paper. The subsequent sections then delimit the recent related literature
first by which data mining tasks are done with wearable sensor data (Section 3), then by the specific
algorithms used to achieve these tasks (Section 4). Then, a description of the type of data sets which are
collected using wearable sensors is given in Section 5. Finally, the paper concludes with a discussion of
future challenges in Section 6 and a conclusion in Section 7.
2. Related Review Papers
Several comprehensive reviews about the subject of health monitoring with wearable sensors have
been previously presented in the literature. Many such reviews focus on giving a global overview of
the topic. Studies on health monitoring systems include wearable, mobile and remote systems [10].
Most notably, are works such as [10,17] which focus on the needs to have wearable sensors and
overcoming important bottlenecks for the use of wearable sensors such as the clinical acceptability
and interoperability in health records. According to [17,18], smart wearable systems supports complex
healthcare applications and enable low-cost wearable, non-invasive alternatives for continuous 24-h
monitoring in Bioinformatics, imaging informatics, clinical informatics, and public health informatics.
However, in real time analysis of sensor data while considering mobile health monitoring systems,
the time of data analysis and resources for data processing is important as it is presented in [10].
Similar works have been done by [12,19] where the authors also provide a useful mapping between
specific diseases and which vital sign parameters can be measured are relevant for the disease. Such
diseases and ailments include: cardiovascular diseases, respiratory diseases, diabetes mellitus, renal
diseases, posture and motion control, rehabilitation, Parkinsons disease, stress, neurological disorders,
Alzheimers disease and dementia [10]. More sensor data (except the mentioned vital signs) have
been considered in the literature such as EEG and body temperature [17]. Nevertheless, integration
and interpretation of the sensor signals while considering the state of a patient is still challenging [19].
Similarly, according to [12], subject-specific models in data mining and context aware in data analysis
are still unsolved.
Considering the data mining reviews for healthcare and sensors, today, most of them are related
to general studies for healthcare i.e., well known problems in healthcare with simple and routine data
mining approaches [19]. Recently, Sow [1] categorized the main challenges of sensor data mining in
five following stages: acquisition, preprocessing, transformation, modelling and evaluation. The authors
in [18,20] found the data mining algorithms mainly in two categories (1) descriptive or unsupervised
learning (i.e., clustering, association, summarisation) and (2) predictive or supervised learning
(i.e., classification, regression). However, they are lacking deeper insight into the suitability of the
algorithms for handling the special characteristics of the sensor data in health monitoring systems.

Sensors 2013, 13

17475

3. Data Mining Tasks for Wearable Sensors

Recently, the research area of health monitoring systems has shifted from simple reasoning of
wearable sensor readings (like calculating the sleep hours or the number of steps per day) to the higher
level of data processing in order to give much more information that is valuable to the end users.
Therefore, healthcare services have been focusing on deeper data mining tasks to have deeper knowledge
representation. Based on the selected literature, three types of data mining tasks are predominant. These
three tasks are: prediction, anomaly detection which may include the subtask of raising alarms, and
diagnosis where a decision making process is made to often categorize the data into different groups
depending on the diseases. Each of these tasks is further described in this section. Figure 1 provides a
depiction of each task in relation to three dimensions. The first dimension involves the setting in which
the monitoring occurs. Based on the literature, most monitoring applications which consider home
settings or remote monitoring deal predominantly with prediction and anomaly detection whereas the
applications in clinical settings are typically focused on diagnosis [10,21]. This fact is easily explained
by the growing desire to have a more preventative approach (prediction) via wearable sensors and to
consider the possibility to facilitate independent living in home environments by increasing the sense of
security (alarm). Similarly, in clinical settings much more information is available in order to provide
diagnosis and assist in decision making [18]. A second dimension in the Figure shows the main data
mining tasks in wearable sensors with respect to the type of subjects used. For patients with known
medical records, both diagnosis and specifically the possibility to raise alarms are key tasks. For health
monitoring which typically include healthy individuals who want to ensure the maintenance of good
health, prediction and anomaly detection are used in the literature [22]. The final dimension depicted in
the Figure considers the three main data mining tasks in relation to how the data is processed. For all
three tasks data has been addressed both in an online and offline manner, with more alarm related tasks
being naturally used in the context of online and continuous monitoring [1].
Figure 1. A schematic overview of the position of the main data mining tasks (anomaly
detection, prediction, and diagnosis/decision making) in relation to the different aspects of
wearable sensing in the health monitoring systems.

Online

Health

Patient

Anomaly detection
Alarm

Diagnosis / Decision making

Offline

Prediction

Home / Remote

Clinical

Sensors 2013, 13

17476

Figure 2 provides an outline of the three most used data mining tasks in relation to the vital signs that
can be measured by wearable sensors considered in this review. ECG, which provides mostly the rich
data, is predominantly used for all tasks in comparison to the other types of sensors. Equal emphasis is
placed on anomaly detection and diagnosis and less attention put on prediction. In general, this applies
to the majority of the vital sign parameters in the Figure. However, for health parameters such as heart
rate and blood glucose, the percentage of the tasks dedicated to predication is higher. This is most likely
due to the fact that these parameters are associated with monitoring of specific diseases e.g., diabetes
whereby prediction is an important component [23]. This section further details the definition of each
task depicted in Figures 1 and 2 and provides key related works for each task.
Figure 2. The outline of the distribution of three data mining tasks in relation to the vital
signs measured by wearable sensors considering in this review.

3.1. Anomaly Detection

Anomaly detection is the task of identifying unusual patterns which do not conform to the expected
behavior of the data [24]. The retrieved abnormal patterns in physiological data are significantly valuable
in the medical domain. Detected unusual patterns in health parameters, especially for home monitoring
systems, enables the clinicians to make accurate decisions in short time [25]. Anomaly detection
techniques are often developed based on a classification methods to distinguish the data set into normal
class and outliers [26]. For example, support vector machines [27], Markov models [28] and Wavelet
analysis [29] are used in health monitoring systems for anomaly detection.
According to our review, most of the papers using the anomaly detection approach usually deal
with short term [30] and multivariate data sets [31] in order to characterize the entire the data to find
discords. Some of the papers considered finding irregular patterns in vital signs time series such as
abnormal episodes in ECG pulses [31,32], SpO2 signal [33] and blood glucose level [28], which mostly
discover unusual temporal patterns in continuous data. Few of the papers have used domain knowledge
and predefined information to detect anomalies for decision making such as anomaly detection in sleep

Sensors 2013, 13

17477

episodes [34,35], and finding hazardous stress levels [36]. In online health monitoring systems, raising
alarm as soon as detecting any anomaly in vital signs will be triggered to have instant reaction and such
alarm system are usually designed for monitoring patients in clinical units [33]. However, anomaly
detection task could use offline techniques in order to detect abnormal reading for each individual based
on the historical measurements for the person [28], since the definition of the abnormal patterns can be
different for each subject.
3.2. Prediction
Prediction is an approach that is widely used in data mining field that helps to identify events which
have not yet occurred. This approach is getting more and more interest for the healthcare providers in
the medical domain since it helps to prevent further chronic problems [18] and could lead to a decision
about prognosis [37]. The role of the predictive data mining considering wearable sensors is nontrivial
due to requirement of modeling sequential patterns acquired from vital signs. This approach is also
known as supervised learning models [20] where it includes feature extraction, training and testing
steps while performing the prediction of the data behavior. As the common examples of the predictive
models, authors in [38,39] presented a method which predicts the further stress levels of a subject.
A similar example of using predictive models in healthcare are: blood glucose level prediction [23],
mortality prediction by clustering electronic health data [40], and a predictive decision making system for
dialysis patients [41]. For the sake of the unexpected situations and conditions in environmental health
monitoring (e.g., home), the difficulty of using predictive models is higher than controlled positions
such as clinical units. However, there are several new prediction works which have used experimental
wearable sensor data to perform non clinical health monitoring [26,42].
3.3. Diagnosis/Decision Making
Decision making in diagnosis is one of the main tasks of clinical monitoring systems which is often
based on retrieved knowledge using vital signs, and also other information such as electronic health
records and metadata [43]. The diagnosis/decision making is related to the anomaly detection in data
mining in order to extract useful information of sensor data such as events, outliers, and alarms which
are meaningful for decision [8]. However, a distinction is that diagnosis systems are not necessarily
using abnormal patterns in vital signs to make decisions. Moreover, the complication of the conditions,
especially about patients situations, needs more robust and global information rather than sensors
abnormal patterns alone [43]. Hence, in this paper diagnosis/decision making is considered as a task
in processing physiological data. Some examples of recent works in this area involve estimating
the severity of health episodes of patients suffering chronic disease [4446], sleep issues such as
polysomnography and apnea [47,48], estimation and classification of health conditions [49,50], and
emotion recognition [51]. Most of these researches have used online databases with annotated episodes
in order to have sufficient and trustable real-world disease labels to evaluate the decision making process.
Considering the complexity of the data to infer diagnosis, some researchers frequently used classification
methods on short term clinical data such as Neural Network (NN) [52] and decision trees [51].

Sensors 2013, 13

17478

3.4. Other Data Mining Tasks for Wearable Sensors

The main role of data mining in healthcare monitoring systems is retrieving information (i.e., anomaly
detection, prediction and diagnosis decision making), and there are several tasks considering wearable
sensors that data mining methods are able to carry out. According to [1,19], most healthcare systems are
dealing with the following issues: (1) data acquisition using the adequate sensor set; (2) transmission of
data from subject to clinician; (3) integration of data with other descriptive data; and (4) data storage.
Considering these issues leads to investigate some data mining tasks such as data cleaning, noise
removing, data filtering and compressing as a part of any physiological data monitoring frameworks.
In order to conduct these problems, several data mining techniques are applied such as wavelet analysis
for artifact reduction [53] and data compression [54], rule-based methods for data summarizing and
transmitting [55,56], and Gaussian process for secure authentication [57]. These kinds of tasks appeared
due to this fact that of real-world health monitoring systems are usually dealing with unlabeled and
continuous data [17].
4. Data Mining Approach
In health monitoring systems, the role of data analysis is to extract information from the low level
sensor data and bridge them to the high level knowledge representation. For this reason recent health
monitoring systems have given more attention to the data processing phase in order to catch more
valuable information based on the expert user requirements. Data mining techniques that have been
applied to wearable sensor data in health monitoring systems have varied and it is also not uncommon
that several techniques are used within the same architecture. In this section we outline the most common
approaches used with wearable sensor data to provide valuable information such as mentioned tasks in
Section 2. Regardless of the data mining technique used, the most standard and widely used approach to
mining information from wearable sensors is given in Figure 3.
Figure 3. A generic architecture of the main data mining approach for wearable sensor data.
- Expert Knowledge
- Metadata
Sensor data
(train)

Sensor data
(test)

Preprocessing

Feature
Extraction /
Selection

Modeling /
Learning

applying
model

Detection /
Prediction /
Decision Making

In the figure, the raw sensor data is typically used as a starting point of the data mining approach. Here,
the sensor data is provided for both training data in order to learn the system, make a model of features, as
well as testing data for real-world usage designed model and make the result. This data mining approach
is suggested as a general flow for both supervised and unsupervised data mining solutions in order to
provide any kind of data mining task as result. The main steps of the data mining approach consist

Sensors 2013, 13

17479

(1) data preprocessing; (2) feature extraction and selection; and (3) modelling data learning the input
features (considering expert knowledge and metadata) to perform the tasks such as detection, prediction,
and decision making.
It should be noted that other parameters on data mining and machine learning methods are important
such as expert knowledge, historical data measurements, electronic health records, and stable parameters
(e.g., sex, age). This metadata provides contextual analysis and improves the process of knowledge
extraction [29,57]. An instance is every healthcare system using HR sensor data needs to investigate
the effect of metadata such as age, sex, weight, and medicine in order to have meaningful reasoning
to find i.e., basic abnormal heart rates or to personalize the critical pulses based on the mentioned
metadata [58,59]. The details of the main steps in the data mining approach are presented below:
4.1. Preprocessing
Due to the occurrence of noise, motion artifacts, and sensor errors in any wearable sensor networks,
a preprocessing of the raw data is necessary. Preprocessing in the healthcare domain involves (1) filter
unusual data to remove artifacts and (2) remove high frequency noise [1,13]. According to the literature,
for filtering artifacts, designed modules have usually applied threshold-based methods to filter sensor
data [36,60] or used statistical tools to interpolate the missing data points [61]. For example in ECG
data, several works have been done to improve the quality of signals for accurate analysis [29,32]. To
remove frequency noise, the other methods in frequency domain such as such as power spectral density
(PSD) fast Fourier transforms (FFT), and low-pass/high-pass filtering tools are common to remove the
fluctuations in sensor signals [51,62]. When the data is gathered from numerous wearable sensors,
normalization and synchronization of sensor data is required. The main challenges of the preprocessing
phase in healthcare systems are addressed in [1] which includes data formatting, data normalization, and
data synchronization. However, there is no tailored work considering these issues in detail for real life
scenarios. Since the gathered sensor data is often unreliable and massive, the papers working with large
scale and continuous data necessarily employed a preprocessing step [45].
4.2. Feature Extraction/Selection
Generally, for mining massive and real world data sets, the abstraction of raw data in any data mining
approach is a way to design and build a model in order to retrieve valuable information. The aim of
feature extraction is to discover the main characteristics of a data set which are identically representatives
of the original data [63]. Especially in wearable sensor data, according to the magnitude and complexity
of the raw data, feature extraction provides a meaningful representation of the sensor data which can
formulate the relation of raw data with the expected knowledge for decision making [64]. Moreover,
reducing the amount of sensor network data is another task in feature extraction and feature selection
phases which leads to have an arranged vector of features as an input of data mining techniques like
classifier methods [45,60].
Since Wearable sensor data which provide monitoring of vital sign parameters tend to be continuous
time series readings, most of the considered features are related to the properties of time series
signals [42]. Two main aspects of analyzing signals are time domain and spectral domain [14]. In the

Sensors 2013, 13

17480

time domain, the extracted features usually include basic waveform characters and statistical parameters
related to the visible attributes in data stream such as mean, variance, pick counts, etc. [36,61]. In
physiological data, the time-domain features are common, because the traditional decision making
frameworks on vital signs are based on the observable trends in the signal [33]. However, for
extra knowledge about the periodic behavior of time series, research in the medical field has given
more attention to the features acquired from frequency-domains such as power spectral density,
low-pass/high-pass filters, spectral energy, and wavelet coefficients of the signal [29,45]. Table 1
summarises the most appeared features in the literature that extracted from wearable sensor data. As
an example, for the works studying ECG signals, although Bsoul et al. [65] have proposed dozens of
features, the main focus of research is to consider R points (the pick point of each beat), and its properties
in ECG pulses such as R-R intervals, pick counts, etc. [39,64]. Besides the features from these domains,
there are other considered features which such as heuristic and specific field features [61].
Table 1. The summarisation of the most commonly used features of each wearable sensor
data in the literature.
Time Domain

Spectral Domain

Other Features

ECG

Mean R-R, Std R-R, Mean HR,

Std HR [39], Number of R-R
interval [27], Mean R-R, Std
R-R interval [64].

Spectral energy [27,62], Power

spectral density [32], Low-pass
filter [45], Low/high
frequency [39,64].

SpO2

Mean, zero crossing counts,

entropy [48], Mean, Slope [61],
Self-similarity [60].

Energy, Low frequency [60].

Drift from normality range [61],

Entropy [60].

HR

Mean, Slope [61], Mean,

Self-similarity, Std [60].

Energy, Low/high frequency [60],

Low/high frequency [36],
Wavelet coefficients of data
segments [45], Low/high
frequency, Power spectral
density [42].

Drift from normality range [61],

Entropy,
Co-occurrence
coefficients [60].

PPG

Rise Times, Max, Min,

Mean [36].

Low/high frequency [36].

BP

Mean, Slope [61].

Rule based features [56].

RR

Mean, Min, Max [64].

Residual and tidal volume [64].

Zero crossings count, Peak

value, Rise time (EMG) [68],
Mean, Duration (GSR) [36],
Pick value, Min, Max
(SCR) [51], Total magnitude,
Duration (GSR) [39].

Spectral energy (EEG) [27],

Median and mean Frequency,
Spectral energy (EMG) [68],
Energy (GSR) [36].

Other

Bandwidth,
(GSR) [36].

Peaks

count

Sensors 2013, 13

17481

Depending on the size of the extracted features from raw data, and the ability of the learning method
to handle these data, feature selection is an effective solution in order to select more discriminative
features. Feature selection methods usually find a subset of high dimensional data which are more
irrelevant and contribute to the performance of the learners [60]. For physiological data, using feature
selection techniques leads to reduce the dimensions of input data. Three most popular approaches for
dimension reduction in medical domain are PCA, ICA, and LDA [66] which are statistically selecting
the subset of the most significant features [45,67]. Other tools for feature selection used in the literature
includes threshold-based rules [61], analysis of variance (ANOVA) [51], and Fourier transforms [52].
Although most of the proposed frameworks in the healthcare domain contain feature
extraction/selection phases, the main challenge still is to balance between the optimum feature
extraction/selection methods and their costs for the system. For instance, it would be costly to use feature
selection in real time systems since the modeling techniques can handle the raw extracted features. In
these cases, the framework has to deal with unnecessary redundancies which reduce the accuracy of
results. The mentioned challenge is directly related to considering (1) selected health parameters in the
system and (2) data mining tasks or the target of the health monitoring system. However, its solution is
still to be addressed in recent research.
4.3. Modeling and Learning Methods
When such sensors are deployed in applications such as home monitoring, a large amount of data
can be generated. Further, when multiple sensors are used, this data is multivariate with possible
dependencies. This means that in order to make sense of the data, appropriate data processing techniques
are essential [1]. In this section we outline the most common algorithms used with wearable sensor data.
Each algorithm is given in technical detail with the most representative examples on how the algorithm
has been applied in healthcare services. In addition, the usability, efficiency and challenges of each
technique in the medical domain are indicated.
4.3.1. Support Vector Machines
A support vector machine (SVM) is one of the main statistical learning methods which is able to
classify unseen information by deriving selected features and constructing a high dimensional hyper
plane to separate the data points into two classes in order to make a decision model [69]. As the SVM
has the ability to handle high dimensional data using minimal training set of features, it is recently very
popular for mining physiological data in medical applications.
Common health parameters considered by SVM methods are ECG, HR, and SpO2 which are mostly
used in the short term and annotated form. Hu et al. [62] used SVM to find out arrhythmia in ECG
signals. It applied a binary classifier version of SVM to categorize ECG signals into normal and
arrhythmia classes. Similarly, [27] developed an SVM method for detecting the arrhythmia and seizure
episodes while ECG signals. This research showed that the SVM method with polynomial kernel leads
to better result rather than other kernels. Detection of the patients condition is the topic of [44] which
used a one-against-all SVMs method in order to handle multi-label classification. Based on the experts
labels on data episodes (4 levels of the severity), several binary SVMs with different kernels such as

Sensors 2013, 13

17482

RBF, polynomial, and sigmoid are combined to model the input data from multi sensor features. Special
usage of SVM classifier is addressed in [32]. This work identified the bad notch in the subjects of chronic
gastritis and arthritis with binary classifications of normal and abnormal radial pulses of ECG using the
SVM algorithm. The input of the method the reduced power spectral density features of pulse. The
performance of the method is evaluated with the sensitivity, specificity, and accuracy of the results.
In general, SVM techniques are often proposed for anomaly detection and decision making tasks in
healthcare services. However, SVM is not an appropriate method to integrate domain knowledge in order
to use metadata or symbolic knowledge seamlessly with the measurements from the sensors. Moreover,
like other classifiers, SVM could not be applied to find the unexpected information from unlabelled data.
4.3.2. Neural Networks
A Neural Network (NN) is an artificial intelligent approach which is widely used for classification
and prediction [70]. The NN method models the train data by learning the known classification of the
records and comparing with predicted classes of the records in order to modify the network weights for
the next iterations of learning. Due to the admissible predictive performance of NN, it is presently the
most popular data modeling method used in the medical domain [37]. The ability of the NN is to model
highly nonlinear systems such as physiological records where the correlation of the input parameters is
not easily detectable [71].
A wide range of the diagnosis and decision making tasks has been done by NN in the medical domain.
NN has also been applied for multi-sensor networks in order to handle the sophisticated analysis of
multivariate data. The multi-layer perceptron (MLP) neural network has been applied in [72] to estimate
the quality of the pulses in PPG. This network puts several individual signal quality metrics as input and
then optimizes the number of nodes (220) hidden layer in validation iterations. The result performs in
two classes of signal quality as output. For evaluation of the work, it employed some common indices
such as sensitivity, specificity, and accuracy. Vu et al. [49] proposed a framework to recognize Heart
Rate Variability (HRV) patterns using ECG and accelerometer sensors. This method used a three layer
neural network to incrementally learn the extracted patterns and classify them. Three nodes in the output
layer identified three classifications of data for location, activity and heart status. Replicator Neural
Network (RNN) [73] is another type of NN which is generally used for anomaly and outlier detection.
Recently, Chatterjee et al. [23] suggested an RNN to predict blood glucose levels. They designed the
network with 11 input variables, one output node as predicted BG level and three hidden layers each with
8 neurons. Online classification of sleep/awake states is another research [52] based on a feedforward
neural network on ECG and RR features in the frequency domain. This network is designed in three
different architectures (without hidden layer) which differed in the type of input signal. For evaluation,
this work used other clinical parameters (e.g., EEG) to monitor and label the collected data. Other
examples of the works who has dealt with NN are [45,74,75].
In sum, since the progress of learning in NN would be complex, the method is commonly used for
decision making in clinical conditions with large and complicated data sets. But same as SVM it could
not handle domain knowledge to enrich the results. Additionally, as the modeling process in NN is a
black box progress, NN method needs to justify for each input data. So, NN is not counted as a portable
technique to easily apply for diverse data sets.

Sensors 2013, 13

17483

4.3.3. Decision Trees

To make an accurate discrimination for selected features, the decision tree method is one of the
significant learning a technique which provides an efficient representation of rule classification [51].
In this method, the most robust features have been detected for initial splitting the input data by creating
a tree-like model. Decision tree is a reliable technique to use in different areas of medical domain
in order to make a right decision [76,77]. Nowadays, upon dealing with complex and noisy data, the
C4.5 algorithm is used which is estimating the error rate of initial nodes and pruning the tree to make a
more efficient sub-tree [41,51].
More attention has been given to decision trees in medical domain when short term data with few
numbers of subjects has been used. This method is also suitable for handling multivariate sensors due to
construction of independent levels in the decision tree. Frantzidis et al. [51] provided a new technique
for motion recognition. It used C4.5 decision tree algorithm based on the Mahalanobis distance to
divide positive or negative emotions of subject while viewing affective pictures. The tree is designed
using the features of biosensor data in two layers of emotion discriminations. The applied classifier
used a rule-based method in order to make a proper decision. Prediction of heat stress risk is another
classification task [26] which is considered with decision trees. This method used the input parameters
such as mean skin temperature, cooling actuation, and ambient temperature and with applying some
rules in order to make a C4.5 tree. The output of the tree is a label of danger or safe with 95% accuracy.
Another suggested application of decision tree in this field is addressed by Bellos et al. [46,64]. In [46]
a decision support system is developed to classify the severity of health level using Random Forest (RF)
classification as a version of the decision tree. This method used a fusion system to combine the severity
of chronic disease for ECG and HR data. For the construction of each tree of the forest, a new subset of
the features was picked. For selecting the best tree, the method used threshold-based rules. The accuracy
of the system has been checked with some predefined targets. Other applications of decision trees in
healthcare services are mentioned in [29,39,41]
Generally, decision tree methods are limited to the space of the constructed features as the inputs
of the model. So, finding hidden information out of constricted features would not be recognizable.
Furthermore, since the number of features can impact on the efficiency of the method, decision tree
models are not usually applied to big and complex physiological data. However, all the mentioned tasks
in Section 3 have been addressed in the literature with a decision tree solution, because it is simple and
easy to implement.
4.3.4. Gaussian Mixture Models
Gaussian mixture model (GMM) is another statistical model which used for classification and pattern
recognition [57]. This method is based on this assumption that the input data are a linear combination
of Gaussian distributions. After random initializing some parameters as the first step of the method,
the model in GMM is re-estimated based on the raw data and computed the conditional probability
density of each target class [45]. Studies using GMM usually deal with annotated medical data in
order to assess the performance of the model. Wang et al. [57] proposed a GMM method using
inter-pulse interval (IPI) signals of ECG in order to make the secure body sensor communications.

Sensors 2013, 13

17484

This tool is based on the fact that the ECG signal behavior is unique for each person and could be
used as a signature for authenticating other knowledge (e.g., medication delivery content information).
Clifton et al. [31] presented a principled approach to increase the ability of personalizing patient
monitoring using Gaussian process. This framework used Gaussian process to estimate reliably the
distribution of the values of the physiological data. Then it detects anomalous in SpO2 channel using the
mean function of Gaussian process. The method has been developed to improve removing artifacts and
missing data from individual subjects. Another research using GMM is a recent work [45] proposing
an automatic detection the coronary artery disease conditions with ECG signals. This method used
several classification methods (i.e., SVM, NN, GMM) in order to categorize signal episodes to normal
and chronic state. The results of this work showed that GMM classifier provided highest accuracy.
Despite GMM is able to detect unseen information in physiological data, it has been rarely used for
prediction tasks. Since the computation time of constructing the models is high, applying GMM in
real-time frameworks is not affordable. Moreover, the initialization step in GMM does not necessarily
enrich the modeling (as GMM approached assume data as a combination of Gaussian distinction) due to
the character of health parameters in real world situations.
4.3.5. Hidden Markov Models
Hidden Markov model (HMM) is a probabilistic model which is convenient for modeling sequential
data [78]. Usually, signals are modeled as a Markov chain to compute the probability of each states
occurrence by calculating a histogram of the probabilities of successive states [79]. Using this model
the hidden states can be inferred from the other observations in sequence of data [80]. Zhu et al. [28]
presented an HMM model to detect the abnormal values in measured blood glucose level. In this work,
the HMM used the history of normal measurements of each person as a benchmark and then it finds the
unusual data in a test set. The state transition diagram of the HMM includes sleep, fasting, and meal
states which are connected with the probability of the BG level for each transition. Another work on
HMM focused on detecting salient segments in the discovered motifs of wearable sensor time series [81].
The performance of this model was evaluated by ECG and accelerometer sensor data. This work used
Markov chain to model the signals with computing the probability of each segment. Segments with the
lowest probabilities are counted as salient (only interesting segments).
In general, HMM is used for anomaly detection rather than any other tasks. Additionally, to the best
of our knowledge, this method has not been applied to multi health parameters analysis and big data sets.
However, based on the abilities of HMM to model the unexpected behaviors of the data, it is applicable
to use the modified versions of HMM in more problems in healthcare domains.
4.3.6. Rule-Based Methods
Rule-based reasoning (RBR) is a simple method to recognize patterns, anomaly and specific events
based on the predefined and stored rules and conditions. Due to the basic task of the healthcare
monitoring which is to find the obvious problem in physiological data, the RBR phase is necessary to
apply on any wearable sensor framework [82]. A domain-specific expert system is a common rule-based
method that defines and applies the expert conditions during data analysis [8385]. A rule-based method

Sensors 2013, 13

17485

is designed by [16] to detect different types of arrhythmias using ECG sensor data. In this work, a
set of threshold-based rules is provided to apply to the ECG features in order to distinguish different
arrhythmias such as Bradycardia, Tachycardia, Premature Ventricular Contraction (PVC), Premature
Atrial Contraction (PAC) and Sleep Apnea. Obviously, the definitions of the conditions (range of values)
for various features in ECG signal are acquired from expert system. Dealing with the general anesthetic
problem is the subject of another research [86] which it has an online query processing algorithm which
supports data stream queries asked by the expert of the system. The detection of the trends such as up,
down, and flat in the time series data is based on the simple logical rules. The aim of this work is to
directly monitor various requested trends by clinicians.
Since rule-based methods are using a set of provided rules by experts or the domain knowledge, they
are able to perform anomaly detection task and to deal with unlabeled data sets to find unusual patterns.
However, these methods are biased to the predefined rules in order to learn the features and behavior
of the data itself. The rule-based methods are not adequate for decision making and prediction tasks as
well as the personalized system with context aware targets. Moreover, they could not handle complex
physiological data in real world experiments with unexpected patterns.
4.3.7. Statistical Tools
Aside from the above mentioned techniques, other general statistical parameters and probability
functions have been used for data mining techniques in the literature [39,53]. In the most of research
in health monitoring systems, dealing with the simple statistical parameters (e.g., mean, variance etc.)
or statistical functions e.g., risk function [61], factor analysis [68]) would be adequate to formulate the
data and retrieve the expected information [38]. This kind of data analysis more or less applied on multi
sensor networks in order to simplify the data features for model construction [30]. Commonly, statistical
tools are modeling the input physiological data based on the statistical features and behaviors of health
parameters. Thus, these models are able to detect the types of anomalies which are not easily seen by the
expert. Nevertheless, domain knowledge and context metadata cannot be integrated with the statistical
models. Despite that these tools are not reliable for decision making tasks, they have been used in clinical
conditions with short term data in order to monitor the principal changes in the data stream.
4.3.8. Frequency Domain/Wavelet Analysis
Analysis of time series data in the frequency domain enables to extract unseen patterns and trends
across data [87]. Same as statistical tools, focusing on frequency domain, especially for wearable
sensor time series data raises up meaningful information of data features. Both Fourier and wavelet
transform analyses have been addressed in this literature mostly for feature selection step [29,52] and
other tasks like estimation vital signs [88] and time series filtering and noise reduction in physiological
data [54,89]. Frequency domain analysis is able to model and find complex patterns and detect the non
obvious anomalies in the data. However, since the computational times in these techniques are high, it is
not an appropriate to use these tools for real-time decision making systems. Furthermore, these models
have not commonly applied for predication task due to the lack of domain knowledge in their models.

Sensors 2013, 13

17486

4.3.9. Other Methods

Out of considered methods, there are other data mining techniques, which are roughly used in
physiological data analysis. Some other examples are mentioned here: Bayesian network for classifying
stress level [26,39] or for predicting patients state [72], Fuzzy state machine for estimating the health
status to provide alerts [68], logistic regression models [42] and association rules [41] to predict stress
level and hospitalization of hemodialysis patients, respectively.
According to the survey, Figure 4 presents the application of data mining methods in relation to
the health parameters gathered with wearable sensors is depicted. It can be seen that ECG, HR, SpO2
and RR are the most complex health parameters where researchers have applied several data mining
techniques to analyze these vital signs. Considering the data mining methods, SVM, NN, decision tree
and frequency/wavelet are commonly used methods for wearable sensor data processing though they
have seen more often only on the ECG health parameter.
Figure 4. The outline of the application of data mining methods in relation to the vital signs
measuring with wearable sensors.

5. Data Sets and their Properties

In any health monitoring system, having a robust data processing stage requires adequate information
about the data itself. In other words, dealing with the type of input data and its properties is the
prerequisite of any data processing system in order to handle the significant issues such as: selecting
the proper data mining approach, designing and adjusting new method and features, and tuning the
parameters of data analysis. To understand the main considered sensor data in the current research
area, this paper examines the types of data and the method for gathering data that have been used in
the experimental validation in the literature. This information gives the opportunity for the readers to
distinguish the applied data processing methods based on the type of sensor data. This section provides

Sensors 2013, 13

17487

detail on the type of data that has been collected using wearable sensors with considering two aspects:
data acquisition approaches and data set properties.
5.1. Data Acquisition
Several input sources and data acquisition methods have been considered in the literature for wearable
sensor data in health monitoring systems. Here, three major data gathering approaches have been
identified such as experimental wearable sensor data, clinical or online databases of sensor data, and
simulated sensor data. It is notable that depending on the mentioned tasks in Section 3, the data sources
used in the literature were different.
Experimental wearable sensor data: The papers which have developed the health monitoring
systems have mostly used their own data gathering experiments to design, model and test the data
analysis step [26,38,88]. In this case the gathered data are usually obtained based on the predefined
scenarios due to the test and evaluate the performed results [36], but usually these studies do not
provide the precise annotations and meaningful labels on physiological signals.
Clinical or online databases of sensor data: Despite the attention of articles in this review is the
role data mining on vital signs in health monitoring, several studies in this area have used the stored
clinical data sets [31,89]. In other word, developed data mining methods is defined and designed
for wearable health monitoring systems, but to evaluate quantitatively and test the performance
of output decision of the framework, the most of the works used categorized and complex
multivariate data sets with formal definitions and annotations by domain expert [30,40,45]. Very
common example of online databases is PhysioNet [90,91] database which consists a wide range
of physiological data sets with categorized and robust annotations for complex clinical signals.
Several papers in the literature have used two main data sets in physioNet bank, MIMIC data sets
(e.g., [53,60,61]) and MIT data sets (e.g., [27,54,92]) that contain the time series of patients vital
signs obtained from hospital medical information systems.
Simulated sensor data: For the sake of having a wide controlled analysis system, few works
have designed and tested their data mining methods through shapely simulated physiological
data [49]. Data simulation would be useful when the more focus of data processing method is
on the efficiency and robustness of information extraction [28,57] rather than handling real-world
data including the artifact, errors, conditions of data gathering environment, etc. Another reason
to create and use simulated data is the lack of long term and large scale data sets [28] which helps
the proposed data mining systems to deal with huge amount of data.
5.2. Data Properties
In addition to the data gathering methods, further properties of the wearable sensor data have been
considered. In this subsection describes the investigated properties of data sets such as time horizon,
scale, labeling, continuous/discrete, and single sensor/multi sensors data.
Time Horizon (long term/short term): The length of time for considering data set measurements is
a particular challenge for wearable sensor data in order to orientate the data mining techniques and

Sensors 2013, 13

17488

the manner of data interpretation. Based on the purpose of any health monitoring system, the time
horizon of data would be mattered. In this review paper, the time horizon of considered sensor data
is categorized to short term and long term data. Some data analysis systems in healthcare were
designed to process short signals such as few minutes of ECG data [74,92], a few hours of heart
rate or oxygen saturation [60,61] and the measurement of blood pressures for a day [56]. On the
other hand, dealing with long term data is the significant portion of some data mining methods for
handling and processing lengthy period of sensor data. This period could be more than a number
of days or a year of measurements. Blood glucose monitoring is an example of long term data
analysis for the sake of right decision making [23,28].
Scale (large/small): A big challenge of data analysis in any health monitoring system is the
examination of the proposed method on more than an individual. Depending on the design of
sensor network, data gathering, and the goal of decision making, the scale of subjects in the
frameworks would differ. Here, the works considering a big number of subjects (patient or healthy)
are counted as large scale studies [30]. The aim of these works is in addition to process the stream
of data individually, they can handle the same data modelling for large scale of monitoring [31].
Due to the type of data mining tools, another group of papers focused on small scale of subjects
(maybe one or at most 10 persons) in order to investigate the accuracy and correctness of results
in proposed model [27,53].
Labeling (annotated/unlabeled): Health monitoring systems need to evaluate their results in
order to show the correctness of the decision making process. Due to have significant data
analysis step, attention of the most research is given to annotated data. By considering the
behavior of vital signs the domain expert would able to mark the data with several annotations
such as arrhythmia disease [27], sleep discords [47], severity of health [61], stress levels [36],
and abnormal pulse in ECG [32]. These annotations also acquired using another source of
knowledge like electronic health record (EHR), coronary syndromes, and also history of vital
signs [40]. Notice that these annotations are not necessarily marked on sensor data episodes,
such some final decisions for the scenarios may be applied to the data set as labels [36,45].
On the other hand, working with unlabeled data leads to have unsupervised learning methods
in order to extract unseen knowledge among raw sensor data. Some researches have been done
on unlabeled data in order to consider uncontrolled situations for especially experimental data
sets [39,44,88].
Continuous/Discrete: Based on the design and architecture of wearable sensors the continuity of
sensor data would be continuous or discrete. From the data mining point of view, the continuity of
physiological data is important, since dealing with streams of sensor data has its own problems and
challenges as well as analyzing sporadic measurements [30]. Due to the nature of vital signs, some
of them are essentially counted as continuous such as ECG, heart rate and respiration rate [31,42]
or discrete like blood glucose level [28]. Blood pressure data is an example which has been
appeared in the literature in both continuous and discrete format [30,75].
Single Sensor/Multi Sensors: Due to have robust decision making in any health monitoring
system, the number of considered vital signs has a significant role to orientate and improve the
results. Usually single sensor data have been used for specific analysis on individual physiological

Sensors 2013, 13

17489

data such as ECG signal analysis [32,54,92] or blood glucose monitoring [23,28]. Besides the
works focusing on physiological data mining gathered from a single sensor, most of the researches
have used several sensors [30,40,44,67] to have global reasoning in health monitoring. Although
using several wearable sensors in health monitoring frameworks are common, but few researches
have really performed the multivariate data analysis in order to extract effective information
through multi sensor data [30].
A meaningful way to utilize the above elicited information about data sets is to consider their usage
in the literature due to infer the role of data sources and data properties in data mining works. For
this reason, the distribution of selected research for each data properties with the relation to the data set
acquisition approaches have been shown in Figures 5 and 6. As can be seen from Figure 5, more attention
has been given to short term data sets which can be easily recorded and analyzed for straightforward
solutions in both experimental and clinical conditions. Beside, large scale data is typically more available
in clinical settings and online databases where more resources are available.
Figure 5. The distribution of works on two sensor data properties (time horizon and scale),
with the relation to three types of data acquisition.

Figure 6 depicts the distribution of works on the other data properties. In a clinical setting and
online databases, data is mostly characterized as continuous and labelled (as access to the experts and
other health profiles is readily available). Wearable sensor data collected in other contexts are rather
unlabeled. In this field relatively little data is discrete and is usually collected in conjunction with other
sensor modalities.

Sensors 2013, 13

17490

Figure 6. The distribution of works on three sensor data properties (continuous/discrete,

labeling, single sensor/multi sensors), with the relation to three types of data acquisition.

Table 2. The outline of the categorization of selected papers based on the type of wearable
sensor data and data set properties.
Horizon

Scale

labelling

long term

short term

large scale

small scale

annotated

ECG

[31,35,47,48,
67,93]

[27,30,32,34,
42,45,49,54,
57,64,81,92,
94]

[3032,45,47,
48,67,74]

[27,34,39,42,
44,49,52,81,
94]

[27,32,45,4749,
52,54,57,81,92,
94,95]

[30,34,35,39,
42,44,46,62,
93]

SpO2

[31,33,40,48,
93]

[44,53,60,61]

[31,40,48,60,
61]

[33,44,53]

[31,33,40,48,53,
61]

[44,60,86,93]

HR

[31,40,47,75]

[26,38,44,60,
61,96]

[26,40,47,60,
61,75]

[38,44,96]

[26,38,40,47,61,
75]

[44,60,86,96]

PPG

[67,72,93]

[36,53,88]

[36,67,72]

[53,88]

[36,53,67,72]

[88,93]

BG

[23,28,40]

[40]

[23,28]

[40]

[23,28]

RR

[40,67,75,86]

[30,34,42,46,
52,64]

[30,40,67,75,
86]

[34,42,46,52,
64]

[40,52,67,75]

[30,34,42,46,
64,86]

BP

[40,56,75]

[30,61]

[30,40,61,75]

[56]

[40,61,75]

[30,56]

[36,51,55,68]

[33,41]

[33,51,55,68]

[36,41]

[51,55,68]

[33,36,41]

Other

unlabelled

In Table 2, particular focus is placed on the relation between the vital signs and most of data properties
in order to present the distribution of the current research based on the review articles. This table aims
to help such researchers who are interested to find out some developed data processing approaches on

Sensors 2013, 13

17491

the specific health parameters with characteristic properties of wearable sensor data. On considering
time horizon, Since the short term data sets are easily acquired and processed, they have been more
used than long term for the most of the health parameters excluding BG, BP which need naturally long
term data to analyze. For the scale property, the large scale data sets are more popular than the small
scale for most of the health parameters, except ECG and BG due to the fact that they contain the high
frequency of available data sets in online databases. Most of the health parameters are used the annotated
data sets rather than the unlabeled measurements excluding BG and RR, Since there is no adequate
predefined annotations to be marked on specific temporal data. Most studies have been conducted on
ECG sensor signal, where all types of data has been used i.e., long/short term, large/small scale, and
annotated/unlabeled data properties.
6. Discussion and Future Challenges
Data mining techniques have progressed significantly in the past few years and with the availability of
large and open data sets, new possibilities for achieving suitable algorithms for wearable sensors exist.
Still, despite these developments, their application to health monitoring is hindered by the challenges
that are present in data from wearable sensors which create new challenges for the data mining field.
This review paper has overviewed the data mining approaches used for wearable sensing devices that
measure vital signs. For each approach, a reflection of its suitability for health monitoring was provided.
From these reflections, the following guidelines for applying data mining methods was extracted:
The selected data mining technique is highly dependent on the data mining task to be performed.
According to the considered data mining tasks in Section 3, for anomaly detection task, SVM,
HMM, statistical tools and frequency analysis are more commonly applied. Nevertheless, NN
has not been addressed to detect anomalies. Prediction tasks on the other hand, have often
used decision tree methods as well as other supervised techniques. It was shown that rule-based
methods, GMM, and frequency analysis are not the most appropriate methods for predication due
to the shortcoming in modeling the data behaviors. Finally, any decision making task needs a
strong modeling and inferring system with a proper usage of the contextual information. So, the
role of statistical methods in this task is less, but SVM, NN, and decision tree techniques have
usually applied for the healthcare problems with decision making tasks with good success.
The requirements for a real-time system should guide the selection of the data mining methods. To
design a real-time health monitoring system, such methods like NN, GMM, and frequency analysis
are not efficient for the sake of their computational complexities. But simple methods such as
rule-based, decision tree and statistical techniques can quickly handle the online data processing
requirements.
The properties of the data set and experimental condition also influence the choice of method. Data
mining methods (e.g rule-based, decision tree) have been used in clinical situation with controlled
conditions and clear data sets, but the efficiency of them are not tested in real experiments of
healthcare services. In contrast, some studies in the literature have used NN, HMM, and frequency
techniques in order to handle complex physiological data and discover the unexpected patterns in
real world situations.

Sensors 2013, 13

17492

The level of supervision and labelled data is key factor to consider. Considering data properties in
the selected research, such methods like SVM, NN, and GMM have been designed and justified
to model long term data. However they could not deal with the unlabeled data in order to model
in an unsupervised manner the raw data and features. For multivariate analysis of wearable sensor
data, the methods working with domain knowledge such as rule-based, decision tree, and statistical
tools are more usable, while GMM and HMM could not play this role in healthcare systems.
While these guidelines can assist those implementing technical systems to select appropriate methods
for data analysis, the field is still challenged by a number of factors which have been discussed in this
paper. These challenges are general challenges in the field of health monitoring and have emerged from
the literature study performed here. They include:
Need for Large scale monitoring in non-clinical context: One challenge is that still many
applications using larger data sets and still consider monitoring in clinical contexts. This means
that it will become of increasing importance for applications, which examine target groups such as
elderly, healthy persons etc. to make significant effort in collecting reliable data sets for processing.
Dealing with annotated data sets: Data mining approaches gain increasing attention in this field,
open data sets as well as benchmark data sets become important in order to validate different
approaches. Still however in this area few benchmark data sets are available. The last mentioned
point raises a second challenge of how data annotation (labeling) can be best done for such target
groups. The process of annotating data is expensive, time consuming and non-trivial considering
long-term continuous data. To confront this challenge, an interesting avenue of study will be the
efficacy of data mining in unsupervised contexts using unlabeled data sets. This applies both to
the modeling as well as eventual preprocessing of data, where for example, unsupervised feature
learning techniques [97] for time series data could show promise.
Multiple measurements: Another challenge in this field is to exploit the multiple measurements
of vital signs simultaneously. In particular, sensor fusion techniques which are able to consider
dependencies and correlations between different vital sign parameters could assist in performing
the main data mining tasks of prediction, decision making and anomaly detection. Some attention
to this issue has been given in the literature such as [30].
Contextual information: As hardware architectures allow for more parameters to be collected,
more information could readily be collected. In addition, usage of contextual information to assist
in data mining is of ever increasing importance. Such contextual information could include meta
information about subjects such as weight, height, age, sex, history of vital signs, as well as history
of previous decisions. It is also possible to automate the retrieval of high level information via
available ontologies [98,99] and link this information to the data.
Reliability, level of trust to the system: A caveat with automated data mining and black box learning
methods is the amount of trust between the data analysis system and the experts who use the system
for decision making tasks. For this reason, different approaches such as case based reasoning [100]
may increase the level of trust by being explicit and referring to previous cases. However, it is still
a big challenge that experts using healthcare services are not sufficiently interact with the reactive
and proactive decisions made by the developed system.

Sensors 2013, 13

17493

Discovering of unseen features: Still, important features of the data which may be unintuitive e.g.,
frequency domain features may be needed for providing proper analysis and uncovering important
characteristics from the data which cannot be obtained by hand-engineered features. It also worth
noting that in real world system such as home monitoring, it would be difficult to model the
unexpected features with straightforward techniques.
Post-processing and Representation: As a result of healthcare systems, an upcoming approach
could use classical data mining techniques together with methods such as natural language
generation which uncover trends in the data but also explain the process to both expert and
non-expert users. Works such as [101,102] have demonstrated the possible uses of such systems
in both clinical and experimental contexts.
In sum, the next few years present a subset of new and interesting challenges for the data mining
and wearable sensors communities. As such systems are more readily deployed in real environments,
experimental validation will need to consider realistic and long-term situations. Furthermore, specific
challenges brought forth by the use of wearable sensors will also need to consider data mining methods
that can address such challenges. The result is a move from applying out of the box data mining
algorithms to a more concentrated effort towards novel data mining methods for the wearable sensors in
health monitoring.
7. Conclusions
The aim of this study was to provide an overview of recent data mining techniques applied to wearable
sensor data in the healthcare domain. This article has attempted to clarify how certain data mining
methods have been applied in the literature. It also has revealed trends in the selection of the data
processing methods in order to monitor health parameters such as ECG, RR, HR, BP and BG. Finally,
particular attention was given to elicit the current challenges of using data processing approaches in the
health monitoring systems. For this reason, this paper surveys several solutions provided by healthcare
services by considering distinguished aspects. Namely this paper includes (1) data mining tasks for
wearable sensors (2) data mining approach and (3) data sets and their properties. In particular, the
review outlined the more common data mining tasks that have been applied such as anomaly detection,
prediction and decision making when considering in particular continuous time series measurements.
Moreover, further details of the suitability of particular data mining methods used to process the wearable
sensor data such as SVM, NN and RBR has been described. Further study in this review paper focused
on the sensors data sets features and properties such as time horizon, scale and labeling. Finally, the
paper addressed future challenges of data mining while analyzing the wearable sensors in healthcare.
Acknowledgements
The authors of this work are partially supported by SAAPHO (Secure Active Aging: Participation and
Health for the Old). The SAAPHO project (aal-2010-3-035) is funded by Vinnova Swedens Innovation
Funding Agency and by the Call AAL (Ambient Assisted Living) within the Call 3, ICT-based solutions
for advancement of older persons independence and participation in the self-serve society.

Sensors 2013, 13

17494

Conflicts of Interest
The authors declare no conflict of interest.
References
1. Sow, D.; Turaga, D.; Schmidt, M. Mining of Sensor Data in Healthcare: A Survey. In Managing
and Mining Sensor Data; Aggarwal, C.C., Ed.; Springer: Berlin, Germany, 2013; pp. 459504.
2. Suh, M.K.; Chen, C.A.; Woodbridge, J.; Tu, M.; Kim, J.; Nahapetian, A.; Evangelista, L.;
Sarrafzadeh, M.
A remote patient monitoring system for congestive heart failure.
J. Med. Syst. 2011, 35, 11651179.
3. Youm, S.; Lee, G.; Park, S.; Zhu, W. Development of remote healthcare system for measuring
and promoting healthy lifestyle. Expert Syst. Appl. 2011, 38, 28282834.
4. Malhi, K.; Mukhopadhyay, S.C.; Schnepper, J.; Haefke, M.; Ewald, H. A Zigbee-based wearable
physiological parameters monitoring system. IEEE Sens. J. 2012, 12, 423430.
5. Yamada, I.; Lopez, G. Wearable Sensing Systems for Healthcare Monitoring. In Proceedings of
the Symposium on VLSI Technology, Honolulu, HI, USA, 1214 June 2012; pp. 510.
6. Chen, M.; Gonzalez, S.; Vasilakos, A.; Cao, H.; Leung, V.C. Body area networks: A survey.
Mob. Netw. Appl. 2011, 16, 171193.
7. Custodio, V.; Herrera, F.J.; Lopez, G.; Moreno, J.I. A review on architectures and
communications technologies for wearable health-monitoring systems.
Sensors 2012, 12,
1390713946.
8. Pantelopoulos, A.; Bourbakis, N.G. A survey on wearable sensor-based systems for health
monitoring and prognosis. Trans. Syst. Man Cyber. Part C 2010, 40, 112.
9. Alemdar, H.; Ersoy, C. Wireless sensor networks for healthcare: A survey. Comput. Netw. 2010,
54, 26882710.
10. Baig, M.; Gholamhosseini, H. Smart health monitoring systems: An overview of design and
modeling. J. Med. Syst. 2013, 37, 114.
11. Rashidi, P.; Mihailidis, A. A survey on ambient-assisted living tools for older adults.
IEEE J. Biomed. Health Inform. 2013, 17, 579590.
12. Atallah, L.; Lo, B.; Yang, G.Z. Can pervasive sensing address current challenges in global
healthcare? J. Epidemiol. Glob. Health 2012, 2, 113.
13. Lara, O.D.; Labrador, M.A. A survey on ambient-assisted living tools for older adults.
IEEE Commun. Surv. Tutor. 2013, 15, 11921209.
14. Avci, A.; Bosch, S.; Marin-Perianu, M.; Marin-Perianu, R.; Havinga, P. Activity Recognition
Using Inertial Sensing for Healthcare, Wellbeing and Sports Applications: A Survey. In
Proceedings of the 23th International Conference on Architecture of Computing Systems,
Hannover, Germany, 2223 February 2010; pp. 167176.
15. Mannini, A.; Sabatini, A.M. Machine learning methods for classifying human physical activity
from on-body accelerometers. Sensors 2010, 10, 11541175.
16. Patel, S.; Park, H.; Bonato, P.; Chan, L.; Rodgers, M. A review of wearable sensors and systems
with application in rehabilitation. J. Neuroeng. Rehabil. 2012, 9, 117.

Sensors 2013, 13

17495

17. Chan, M.; Esteve, D.; Fourniols, J.Y.; Escriba, C.; Campo, E. Smart wearable systems: Current
status and future challenges. Artif. Intell. Med. 2012, 56, 137156.
18. Bellazzi, R.; Ferrazzi, F.; Sacchi, L. Predictive data mining in clinical medicine: A focus on
selected methods and applications. Wiley. Interdiscip. Rev.: Data. Min. Knowl. Discov. 2011,
1, 416430.
19. Nangalia, V.; Prytherch, D.; Smith, G. Health technology assessment review: Remote monitoring
of vital signscurrent status and future challenges. Crit. Care 2010, 14, 18.
20. Yoo, I.; Alafaireet, P.; Marinov, M.; Pena-Hernandez, K.; Gopidi, R.; Chang, J.F.; Hua, L.
Data mining in healthcare and biomedicine: A survey of the literature. J. Med. Syst. 2012,
36, 24312448.
21. Stacey, M.; McGregor, C. Temporal abstraction in intelligent clinical data analysis: A survey.
Artif. Intell. Med. 2007, 39, 124.
22. Mukherjee, A.; Pal, A.; Misra, P. Data Analytics in Ubiquitous Sensor-Based Health Information
Systems. In Proceedings of the 2012 6th International Conference on Next Generation Mobile
Applications, Services and Technologies, Paris, France, 1214 September 2012; pp. 193198.
23. Chatterjee, S.; Dutta, K.; Xie, H.Q.; Byun, J.; Pottathil, A.; Moore, M. Persuasive and Pervasive
Sensing: A New Frontier to Monitor, Track and Assist Older Adults Suffering from Type-2
Diabetes. In Proceedings of the 46th Hawaii International Conference on System Sciences,
Grand Wailea, Maui, HI, USA, 710 January 2013; pp. 26362645.
24. Chandola, V.; Banerjee, A.; Kumar, V. Anomaly detection: A survey. ACM Comput. Surv. 2009,
41, 15:115:58.
25. Chandola, V.; Banerjee, A.; Kumar, V. Anomaly detection for discrete sequences: A survey.
IEEE Trans. Knowl. Data Eng. 2012, 24, 823839.
26. Gaura, E.; Kemp, J.; Brusey, J. Leveraging knowledge from physiological data: On-body heat
stress risk prediction with sensor networks. IEEE Trans. Biomed. Circuits Syst. 2013, in press.
27. Lee, K.H.; Kung, S.Y.; Verma, N. Low-energy formulations of support vector machine kernel
functions for biomedical sensor applications. J. Signal Process. Syst. 2012, 69, 339349.
28. Zhu, Y. Automatic detection of anomalies in blood glucose using a machine learning approach.
J. Commun. Netw. 2011, 13, 125131.
29. Gialelis, J.; Chondros, P.; Karadimas, D.; Dima, S.; Serpanos, D. Identifying Chronic Disease
Complications Utilizing State of the Art Data Fusion Methodologies and Signal Processing
Algorithms. In Wireless Mobile Communication and Healthcare; Nikita, K.S., Lin, J.C.,
Fotiadis, D.I., Arredondo Waldmeyer, M.T., Eds.; Springer: Berlin, Germany, 2012; Volume 83,
pp. 256263.
30. Huang, G.; Zhang, Y.; Cao, J.; Steyn, M.; Taraporewalla, K. Online mining abnormal
period patterns from multiple medical sensor data streams.
World Wide Web 2013,
doi:10.1007/s11280-013-0203-y.
31. Clifton, L.; Clifton, D.A.; Pimentel, M.A.F.; Watkinson, P.J.; Tarassenko, L. Gaussian processes
for personalized e-health monitoring with wearable sensors. IEEE Trans. Biomed. Eng. 2013,
60, 193197.

Sensors 2013, 13

17496

32. Thakker, B.; Vyas, A.L. Support vector machine for abnormal pulse classification. Int. J.
Comput. Appl. 2011, 22, 1319.
33. Charbonnier, S.; Gentil, S. On-line adaptive trend extraction of multiple physiological signals
for alarm filtering in intensive care units. Int. J. Adapt. Control. Signal. Process. 2009, 24,
382408.
34. Adnane, M.; Jiang, Z.; Choi, S.; Jang, H. Detecting specific health-related events using an
integrated sensor system for vital sign monitoring. Sensors 2009, 9, 68976912.
35. Adnane, M.; Jiang, Z.; Mori, N.; Matsumoto, Y. An Automated Program for Mental Stress
and Apnea/Hypopnea Events Detection. In Proceedings of the 7th International Workshop on
Systems, Signal Processing and their Applications, Tipaza, Algeria, 911 May 2011; pp. 5962.
36. Singh, R.R.; Conjeti, S.; Banerjee, R. An Approach for Real-Time Stress-Trend Detection Using
Physiological Signals in Wearable Computing Systems for Automotive Drivers. In Proceedings
of the 14th International IEEE Conference on Intelligent Transportation Systems, Washington,
DC, USA, 57 October 2011; pp. 14771482.
37. Bellazzi, R.; Zupan, B. Predictive data mining in clinical medicine: Current issues and guidelines.
Int. J. Med. Inform. 2008, 77, 8197.
38. Silva, F.; Olivares, T.; Royo, F.; Vergara, M.A.; Analide, C. Experimental Study of the Stress
Level at the Workplace Using an Smart Testbed of Wireless Sensor Networks and Ambient
Intelligence Techniques. In Natural and Artificial Computation in Engineering and Medical

Applications; Ferrandez Vicente, J., Alvarez

Sanchez, J., Paz Lopez, F., Toledo Moreo, F.J., Eds.;
Springer: Berlin, Germany, 2013; Volume 7931, pp. 200209.
39. Sun, F.T.; Kuo, C.; Cheng, H.T.; Buthpitiya, S.; Collins, P.; Griss, M. Activity-Aware Mental
Stress Detection Using Physiological Sensors. In Mobile Computing, Applications, and Services;
Gris, M., Yang, G., Eds.; Springer: Berlin, Germany, 2012; Volume 76, pp. 211230.
40. Marlin, B.M.; Kale, D.C.; Khemani, R.G.; Wetzel, R.C. Unsupervised Pattern Discovery in
Electronic Health Care Data Using Probabilistic Clustering Models. In Proceedings of the 2nd
ACM SIGHIT International Health Informatics Symposium, Miami, FL, USA, January 2012;
pp. 389398.
41. Yeh, J.Y.; Wu, T.H.; Tsao, C.W. Using data mining techniques to predict hospitalization of
hemodialysis patients. Decis. Support Syst. 2011, 50, 439448.
42. Choi, J.; Ahmed, B.; Gutierrez-Osuna, R. Development and evaluation of an ambulatory stress
monitor based on wearable sensors. IEEE Trans. Inf. Technol. Biomed. 2012, 16, 279286.
43. Sneha, S.; Varshney, U. Enabling ubiquitous patient monitoring: Model, decision protocols,
opportunities and challenges. Decis. Support Syst. 2009, 46, 606619.
44. Bellos, C.; Papadopoulos, A.; Rosso, R.; Fotiadis, D.I. A Support Vector Machine Approach for
Categorization of Patients Suffering from Chronic Diseases. In Wireless Mobile Communication
and Healthcare; Nikita, K.S., Lin, J.C., Fotiadis, D.I., Arredondo Waldmeyer, M.T., Eds.;
Springer: Berlin, Germany, 2012; Volume 83, pp. 264267.
45. Giri, D.; Rajendra Acharya, U.; Martis, R.J.; Vinitha Sree, S.; Lim, T.C.; Ahamed VI, T.;
Suri, J.S. Automated diagnosis of Coronary Artery Disease affected patients using LDA, PCA,
ICA and Discrete Wavelet Transform. Know. Based Syst. 2013, 37, 274282.

Sensors 2013, 13

17497

46. Bellos, C.; Papadopoulos, A.; Rosso, R.; Fotiadis, D.I. Categorization of Patients Health Status
in Copd Disease Using a Wearable Platform and Random Forests Methodology. In Proceedings
of the IEEE International Conference on Biomedical and Health Informatics, Shenzhen, China,
57 January 2012; pp. 404407.
47. Bianchi, A.M.; Mendez, M.O.; Cerutti, S. Processing of signals recorded through smart devices:
Sleep-quality assessment. IEEE Trans. Inf. Technol. Biomed. 2010, 14, 741747.
48. Xie, B.; Minn, H. Real-time sleep apnea detection by classifier combination. IEEE Trans. Inf.
Technol. Biomed. 2012, 16, 469477.
49. Vu, T.H.N.; Park, N.; Lee, Y.K.; Lee, Y.; Lee, J.Y.; Ryu, K.H. Online discovery of Heart Rate
Variability patterns in mobile healthcare services. J. Syst. Softw. 2010, 83, 19301940.
50. Pantelopoulos, A.; Bourbakis, N.G. Prognosisa wearable health-monitoring system for people
at risk: Methodology and modeling. IEEE Trans. Inf. Technol. Biomed. 2010, 14, 613621.
51. Frantzidis, C.A.; Bratsas, C.; Klados, M.A.; Konstantinidis, E.; Lithari, C.D.; Vivas, A.B.;
Papadelis, C.L.; Kaldoudi, E.; Pappas, C.; Bamidis, P.D. On the classification of emotional
biosignals evoked while viewing affective pictures: An integrated data-mining-based approach
for healthcare applications. Trans. Inf. Tech. Biomed. 2010, 14, 309318.
52. Karlen, W.; Mattiussi, C.; Floreano, D. Sleep and wake classification with ECG and respiratory
effort signals. IEEE Trans. Biomed. Circuits Syst. 2009, 3, 7178.
53. Naraharisetti, K.V.P.; Bawa, M.; Tahernezhadi, M. Comparison of Different Signal Processing
Methods for Reducing Artifacts from Photoplethysmograph Signal. In Proceedings of the IEEE
International Conference on Electro/Information Technology, Mankato, MN, USA, 1517 May
2011; pp. 18.
54. Ding, H.; Sun, H.; mean Hou, K. Abnormal ECG Signal Detection Based on Compressed
Sampling in Wearable ECG Sensor. In Proceedings of the International Conference on Wireless
Communications and Signal Processing, Nanjing, China, 911 November 2011; pp. 15.
55. Yoon, J. Three-Tiered Data Mining for Big Data Patterns of Wireless Sensor Networks in Medical
and Healthcare Domains. In Proceedings of the 8th International Conference on Internet and Web
Applications and Services, Rome, Italy, 2328 June 2013; pp. 1824.
56. Ahmad, N.F.; Hoang, D.B.; Phung, M.H. Robust Preprocessing for Health Care Monitoring
Framework. In Proceedings of the 11th International Conference on E-Health Networking,
Applications and Services, Sydney, Australia, 1618 December 2009; pp. 169174.
57. Wang, W.; Wang, H.; Hempel, M.; Peng, D.; Sharif, H.; Chen, H.H. Secure stochastic ECG
signals based on gaussian mixture model for e-healthcare systems. IEEE Syst. J. 2011, 5,
564573.
58. Hjalmarson, A. Heart rate: An independent risk factor in cardiovascular disease. Eur. Heart
J. Suppl. 2007, 9, F3F7.
59. Gellish, R.; Goslin, B.; Olson, R.; McDonald, A.; Russi, G.; Moudgil, V. Longitudinal modeling
of the relationship between age and maximal heart rate. Med. Sci. Sports Exerc. 2007, 39,
822829.

Sensors 2013, 13

17498

60. Mao, Y.; Chen, W.; Chen, Y.; Lu, C.; Kollef, M.; Bailey, T. An Integrated Data Mining Approach
to Real-Time Clinical Monitoring and Deterioration Warning. In Proceedings of the 18th ACM
SIGKDD International Conference on Knowledge Discovery And Data Mining, Beijing, China,
1618 August 2012; pp. 11401148.
61. Apiletti, D.; Baralis, E.; Bruno, G.; Cerquitelli, T. Real-time analysis of physiological data to
support medical applications. Trans. Info. Tech. Biomed. 2009, 13, 313321.
62. Hu, F.; Jiang, M.; Celentano, L.; Xiao, Y. Robust medical ad hoc sensor networks (MASN) with
wavelet-based ECG data mining. Ad Hoc Netw. 2008, 6, 9861012.
63. Guyon, I.; Gunn, S.; Nikravesh, M.; Zadeh, L.A. Feature Extraction: Foundations and
Applications (Studies in Fuzziness and Soft Computing); Springer: Secaucus, NJ, USA, 2006.
64. Bellos, C.C.; Papadopoulos, A.; Rosso, R.; Fotiadis, D.I. Extraction and Analysis of Features
Acquired By Wearable Sensors Network. In Proceedings of 10th IEEE International Conference
on Information Technology and Applications in Biomedicine, Corfu, Greece, 35 November
2010; pp. 14.
65. Bsoul, M.; Minn, H.; Tamil, L. Apnea medassist: Real-time sleep apnea monitor using
single-lead ECG. IEEE Trans. Inf. Technol. Biomed. 2011, 15, 416427.
66. Widodo, A.; Yang, B.S. Application of nonlinear feature extraction and support vector machines
for fault diagnosis of induction motors. Expert Syst. Appl. 2007, 33, 241250.
67. Li, X.; Porikli, F. Human State Classification and Predication for Critical Care Monitoring by
Real-Time Bio-signal Analysis. In Proceedings of the 20th International Conference on Pattern
Recognition, Istanbul, Turkey, 2326 August 2010; pp. 24602463.
68. Pradhan, G.N.; Chattopadhyay, R.; Panchanathan, S. Processing Body Sensor Data Streams
for Continuous Physiological Monitoring. In Proceedings of the International Conference on
Multimedia Information Retrieval, Philadelphia, PA, USA, 2931 March 2010; pp. 479486.
69. Cortes, C.; Vapnik, V. Support-vector networks. Mach. Learn. 1995, 20, 273297.
70. Paliwal, M.; Kumar, U.A. Neural networks and statistical techniques: A review of applications.
Expert. Syst. Appl. 2009, 36, 217.
71. Amato, F.; Lopez Rodrguez, A.; PenaandMendez, E.M.; Vanhara, P.; Hampl, A.; Havel, J.
Artificial neural networks in medical diagnosis. J Appl. Biomed. 2013, 11, 4758.
72. Li, Q.; Clifford, G.D. Dynamic time warping and machine learning for signal quality assessment
of pulsatile signals. Physiol. Meas. 2012, 33, 14911501.
73. Blonde, L.; Karter, A.J. Current evidence regarding the value of self-monitored blood glucose
testing. Am. J. Med. 2005, 118, 2026.
74. Jin, Z.; Sun, Y.; Cheng, A.C.
Predicting Cardiovascular Disease From Real-Time
Electrocardiographic Monitoring: An Adaptive Machine Learning Approach on a Cell Phone. In
Proceedings of the 31th Annual International Conference of the IEEE Engineering in Medicine
and Biology Society, Minneapolis, MN, USA, 36 September 2009; pp. 68896892.
75. Ordonez, P.; Armstrong, T.; Oates, T.; Fackler, J. Classification of Patients Using Novel
Multivariate Time Series Representations of Physiological Data. In Proceedings of the 10th
International Conference on Machine Learning and Applications, Honolulu, HI, USA, 1821
December 2011; pp. 172179.

Sensors 2013, 13

17499

76. Podgorelec, V.; Kokol, P.; Stiglic, B.; Rozman, I. Decision trees: An overview and their use in
medicine. J. Med. Syst. 2002, 26, 445463.
77. Lopez-Vallverdu, J.A.; Riano, D.; Bohada, J.A. Improving medical decision trees by combining
relevant health-care criteria. Expert Syst. Appl. 2012, 39, 1178211791.
78. Rabiner, L.; Juang, B.H. An introduction to hidden Markov models. IEEE ASSP Mag. 1986,
3, 416.
79. Thomas, O.; Sunehag, P.; Dror, G.; Yun, S.; Kim, S.; Robards, M.; Smola, A.; Green, D.;
Saunders, P. Wearable sensor activity analysis using semi-Markov models with a grammar.
Pervasive Mob. Comput. 2010, 6, 342350.
80. Bae, J.; Tomizuka, M. Gait phase analysis based on a Hidden Markov Model. Mechatronics
2011, 21, 961970.
81. Woodbridge, J.; Lan, M.; Sarrafzadeh, M.; Bui, A. Salient Segmentation of Medical Time Series
Signals. In Proceedings of the First IEEE International Conference on Healthcare Informatics,
Imaging and Systems Biology, San Jose, CA, USA, 2629 July 2011; pp. 18.
82. Al-Hajji, A.A. Rule-Based Expert System for Diagnosis and Symptom of Neurological Disorders
Neurologist Expert System (NES). In Proceedings of the 1st Taibah University International
Conference on Computing and Information Technology, Al-Madinah Al-Munawwarah,
Saudi Arabia, 1214 March 2012; pp. 6772.
83. He, J.; Zhang, Y.; Huang, G.; Xin, Y.; Liu, X.; Zhang, H.; Chiang, S.; Zhang, H. An
Association Rule Analysis Framework for Complex Physiological and Genetic Data. In Health
Information Science; He, J., Liu, X., Krupinski, E., Xu, G., Eds.; Springer: Berlin, Germany,
2012; pp. 131142.
84. Fayyad, U.M.; Piatetsky-Shapiro, G.; Smyth, P. From Data Mining to Knowledge Discovery:
An Overview. In Advances in Knowledge Discovery and Data Mining; Fayyad, U.M.,
Piatetsky-Shapiro, G., Smyth, P., Uthurusamy, R., Eds.; American Association for Artificial
Intelligence: Menlo Park, CA, USA, 1996; pp. 134.
85. Kalagnanam, J.; Henrion, M. A comparison of decision analysis and expert rules for sequential
diagnosis. 2013, arXiv:1304.2362.
86. Zhang, Q.; Pang, C.; Mcbride, S.; Hansen, D.; Cheung, C.; Steyn, M. Towards Health Data
Stream Analytics. In Proceedings of the IEEE/ICME International Conference on Complex
Medical Engineering, Gold Coast, Australia, 1315 July 2010; pp. 282287.
87. Chaovalit, P.; Gangopadhyay, A.; Karabatis, G.; Chen, Z. Discrete Wavelet transform-based time
series analysis and mining. ACM Comput. Surv. 2011, 43, 6:16:37.
88. Scully, C.; Lee, J.; Meyer, J.; Gorbach, A.M.; Granquist-Fraser, D.; Mendelson, Y.; Chon, K.H.
Physiological parameter monitoring from optical recordings with a mobile phone. IEEE Trans.
Biomed. Eng. 2012, 59, 303306.
89. Salem, O.; Liu, Y.; Mehaoua, A. A Lightweight Anomaly Detection Framework for Medical
Wireless Sensor Networks.
In Proceedings of the IEEE Wireless Communications and
Networking Conference, Shanghai, China, 710 April 2013; pp. 43584363.
90. PhysioBank Archive Index. Available online: http://www.physionet.org/physiobank/database/
(accessed on 10 November 2013).

Sensors 2013, 13

17500

91. Goldberger, A.L.; Amaral, L.A.N.; Glass, L.; Hausdorff, J.M.; Ivanov, P.C.; Mark, R.G.;
Mietus, J.E.; Moody, G.B.; Peng, C.K.; Stanley, H.E. PhysioBank, physiotoolkit, and physionet:
Components of a new research resource for complex physiologic signals. Circulation 2000,
101, 215220.
92. Patel, A.M.; Gakare, P.K.; Cheeran, A.N. Real time ECG feature extraction and arrhythmia
detection on a mobile platform. Int. J. Comput. Appl. 2012, 44, 4045.
93. Yang, S.; Kim, J.; Gerla, M. Clinical Quality Guaranteed Physiological Data Compression in
Mobile Health Monitoring. In Proceedings of the 2nd ACM International Workshop on Pervasive
Wireless Healthcare, Hilton Head, SC, USA, 1114 June 2012; pp. 5156.
94. He, X.; Goubran, R.A.; Liu, X.P. Ensemble Empirical Mode Decomposition and Adaptive
Filtering for ECG Signal Enhancement. In Proceedings of the IEEE International Symposium
on Medical Measurements and Applications Proceedings, Budapest, Hungary, 1819 May 2012;
pp. 15.
95. Ramesh, M.V.; Anu, T.A.; Thirugnanam, H. An Intelligent Decision Support System for
Enhancing an m-Health Application. In Proceedings of the 9th International Conference on
Wireless and Optical Communications Networks, Indore, India, 2022 September 2012; pp. 15.
96. Chen, C.M. Web-based remote human pulse monitoring system with intelligent data analysis for
home health care. Expert Syst. Appl. 2011, 38, 20112019.
97. Langkvist, M.; Karlsson, L.; Loutfi, A. Sleep stage classification using unsupervised feature
learning. Adv. Artif. Neu. Sys. 2012, 2012, 107046.
98. Kim, J.; Kim, J.; Lee, D.; Chung, K.Y. Ontology driven interactive healthcare with wearable
sensors. Multimed. Tools Appl. 2012, doi:10.1007/s11042-012-1195-9.
99. Alirezaie, M.; Loutfi, A. Automatic Annotation of Sensor Data Streams Using Abductive
Reasoning. Presented at the 5th International Conference on Knowledge Engineering and
Ontology Development, Vilamoura, Portugal, 1922 September 2013.
100. Ahmed, M.U.; Banaee, H.; Loutfi, A. Health monitoring for elderly: An application using
case-based reasoning and cluster analysis. ISRN Artif. Intell. 2013, 2013, 380239.
101. Banaee, H.; Ahmed, M.U.; Loutfi, A. A Framework for Automatic Text Generation of Trends
in Physiological Time Series Data. In Proceedings of the IEEE International Conference on
System, Man, and Cybernetics, Manchester, UK, 1316 October 2013; pp. 38763881.
102. Hunter, J.; Freer, Y.; Gatt, A.; Reiter, E.; Sripada, S.; Sykes, C. Automatic generation of natural
language nursing shift summaries in neonatal intensive care: BT-Nurse. Artif. Intell. Med. 2012,
56, 157172.
c 2013 by the authors; licensee MDPI, Basel, Switzerland. This article is an open access article

distributed under the terms and conditions of the Creative Commons Attribution license
(http://creativecommons.org/licenses/by/3.0/).