Korg Trinity Manual - Expansion Option - HDR-TRI

HDR-TRI
Hard Disk Recorder Option

Users Guide
Table of Contents
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features of the HDR-TRI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About hard disk recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About hard disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About sound and audio events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
2
2. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Settings for recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hard disk connections and settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Formatting a hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Types of SCSI devices that can be connected and their ID settings . . . 5
Connections for recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Song settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Checking the external input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Recording an audio track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Recording a guitar in stereo on tracks 3 and 4 while listening to audio
tracks 1 and 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
The Compare function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Playing back the track(s) you recorded . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the pan or volume balance of the tracks . . . . . . . . . . . . . . . 12
Recording mixer events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Re-recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using the rehearsal function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using auto punch-in recording to edit. . . . . . . . . . . . . . . . . . . . . . . . . 14
Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Creating repetitions of the same phrase . . . . . . . . . . . . . . . . . . . . . . . 15
Track bouncing (ping-pong recording) . . . . . . . . . . . . . . . . . . . . . . 15
Bouncing MIDI tracks and audio tracks together . . . . . . . . . . . . . . . . 16
Applying master effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Creating a song in conjunction with the MIDI sequencer . . . . . . . . 17
Saving/loading recorded data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Saving song data to a hard disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Loading data from a hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using a recorded sound more than once in the same .SNG file . . . 20
Creating different arrangements using the same vocal . . . . . . . . . . . . 20
Using the same sound more than once . . . . . . . . . . . . . . . . . . . . . . . . 20
3. Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Sequencer P1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15: Audio Track Rec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16: Mix Audio Track 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17: Preference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sequencer P2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25: Audio Track parameter (Audio Track 14) . . . . . . . . . . . . . . . .
Sequencer P5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53: Audio Track Edit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
21
26
29
30
30
31
31
i
Table of Contents
54: Audio Track Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disk P1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11: Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13: Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14: Audio Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
46
46
47
50
4. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
55
56
56
57
This manual explains the functions which are newly added when the
HDR-TRI hard disk recorder option is installed. For the parameters
whose functions remain unchanged, refer to your Parameter Guide, Basic
Guide, and Effect Guide.
Features of the HDR-TRI
4-channel hard disk recorder

16-bit linear PCM recording
A 540 Mbyte hard disk allows approximately 47 minutes of stereo recording
Up to 7 SCSI disks can be connected
Instantaneous cueing
Rehearsal function
Manual or Auto Punch In/Out recording is supported
Editing operations such as Copy, Move, Erase, Delete, Insert, and Edit Undo
Backup to DAT via the S/P DIF OUT connector
Digital EQ
Two master effect sends
About hard disk recording

Realtime recording to an audio track can be performed using Overwrite Recording, Auto Punch-In Recording, or Manual Punch-In Recording. Unlike when
recording to a MIDI track, Overwrite Recording overwrites only the measures
that were recorded.
As when recording to a MIDI track, recording to an audio track creates events
(audio events) which can be edited in detail using the Audio Event Edit functions. Since individual audio events can be edited, you can edit (move, delete,
copy, etc.) even small segments of sound such as orchestra hits.
In addition, the mixer allows you to adjust the pan, volume, etc. for each audio
track, and to record these changes so that they will be faithfully reproduced
when the data is played back.
Operation
In this manual, tracks recorded by the hard disk recorder are referred to as
audio tracks. In contrast, tracks of the sequencer discussed in the
Parameter Guide and Basic Guide are referred to in this manual as MIDI
tracks.
Parameters
Thank you for purchasing the HDR-TRI hard disk recorder option. In order to
enjoy long and trouble-free use, please read this manual carefully.
Appendix
1. Introduction
Introduction
Features of the HDR-TRI
About hard disks
About hard disks

When a hard disk connected to the TRINITY is formatted, it
is divided into two partitions: a filer area and a sound area.
The filer partition is used to save .SNG files and .PCG files,
and also includes an area used to manage these files. The
sound partition is used to record sound.
When you specify the size of the filer partition in the Format
dialog box before executing the Format command, the disk
will be formatted with the remaining space allotted to the
sound partition (page 48 of this manual). In order to modify the partitioning, you must either execute Format once
again, or execute the Wipe command.
Hard Disk
Filer partition
.SNG files
.PCG files etc.
Sound partition
Recorded
sounds
About sound and audio events

When audio recording is performed, sound is recorded directly into the sound
partition of the hard disk. At the same time, event data (audio events) pertaining
to that sound is recorded into the audio track that is currently selected. (The
sound data itself does not exist in the audio track.) Audio events contain data
that specifies the name of the sound that they use, and data that specifies the
portion of the sound that will be played back.
When a song is played back and an audio event is encountered, the appropriate
sound will be played back from the hard disk. This means that playback is not
possible unless the sound itself as well as the audio event that uses that sound
are both present.
Be aware that audio events can be erased using the event edit commands, and
can also be erased by accident by turning the power off before they have been
saved to the hard disk. Furthermore, if just the sound is left, it will not be possible to re-use that sound in an audio track. If you allow these unusable sounds to
accumulate in your hard disk, they will simply occupy disk space to no purpose, so we recommend that you execute the Delete Unused Sound command
(page 53 of this manual) to make the best use of your hard disk.
Settings for recording
Introduction
2. Operation
This section explains how to make the necessary settings for hard disk recording. Be sure to make these settings before performing hard disk recording.
Up to 7 hard disks can be connected using SCSI cables. Use hard disks with a
maximum capacity of 4 Gbytes and an average seek time of 11.5 ms or less.
The TRINITY uses a D-Sub 25-pin connector. The connectors of different hard
disks may vary, so read the manual of your hard disk to check the type of connector it has before purchasing an appropriate SCSI cable.
1 Turn the power OFF for the TRINITY and the hard disk(s).
The power of the TRINITY and any hard disk(s) must be OFF before connecting or disconnecting SCSI cables or changing the ID number of a hard
disk.
Operation
Hard disk connections and settings
If you are connecting two or more hard disks, set them to different ID numbers
so that they can be distinguished.
For details on setting the ID number, refer to the manual for your hard disk.
Setting two or more hard disks to the same ID will cause malfunctions or
loss of data.
3 Connect the SCSI connector of the TRINITY to the SCSI connector of the hard disk.
If you are connecting two or more hard disks, make sure that the total
length of the cables is less than 6 meters (18 feet).
Parameters
2 On the hard disk, set an ID number in the range of 06.
If two or more hard disks are connected, terminate the last hard disk in the
chain (the hard disk furthest from the TRINITY).
Even if only one hard disk is connected, that hard disk must be terminated.
Some hard disks require an externally attached terminator. Others have a switchable terminator built-in. Refer to the manual for your hard disk.
Total length of SCSI cables must be less than 6 meters (18 feet)
SCSI
SCSI
SCSI
SCSI
SCSI
ID0
ID1
ID2
Hard Disk
Hard Disk
Hard Disk
Hard disk must be terminated
Appendix
4 Terminate the hard disk.
5 Turn on the power of the hard disk(s), and then turn on the power of the TRINITY.
When turning on the power, turn on devices in sequence from the hard disk
TRINITY.
When turning off the power, turn off devices in sequence from the TRINITY
hard disk.
Never turn off the power while the hard disk is being accessed (e.g., while
the LED indicator of the hard disk is lit).
Formatting a hard disk

If the hard disk is being used by the TRINITY series for the first time, the hard
disk must first be formatted to establish a filer partition and a sound partition.
When formatting is executed, all data that was previously on that hard
disk will be erased. Before formatting a disk, make sure that it does not
contain data you wish to keep.
The only way to modify the size of the filer partition or the volume label is
to execute formatting once again or to execute the Wipe command.
1 In Disk mode P1 tab 3 page (Utility), use the drive select field to select the hard
disk that you wish to format.
Drive select
When using Drive Select to select a hard disk, the ID numbers of hard disks that
have not been formatted will appear as Unformatted, and the ID numbers of
hard disks that are not connected will appear as None. Even if a hard disk has
been formatted by a personal computer, etc., it will be shown as Unformatted,
and such a hard disk must be formatted as well.
2 Choose the page menu command Format, and the following dialog box will
appear.
3
4
5
3 Assign a volume label (up to 11 characters).
When formatting is executed, this volume label will be displayed in the drive
select area.
4 Specify the size (0540 Mbyte) of the filer partition.

When formatting is executed, the remaining space on the disk will become the
sound partition.
If you are using only a single hard disk to perform hard disk recording,
you must specify a filer partition larger than 0 in order to create an area
where .SNG files and .PCG files etc. can be saved. If you are using two or
more hard disks, a filer partition must be created on at least one of the
disks.
5 Press the OK button to execute formatting.

Formatting a hard disk will require a certain amount of time depending on the
size of the hard disk. (e.g., formatting a 540 Mbyte hard disk requires approximately 5 minutes.)
Introduction
Types of SCSI devices that can be connected and

their ID settings
Appendix
SCSI devices other than hard disks can also be connected, including removable
media such as magneto-optical disks (MO).
Hard disks can be set freely to any ID number 06, but a removable media
device can be used only when its ID number is set to 6.
If you have connected only one removable media device, and no other device is
connected, that removable media can be used to load and save .SNG files.
However if one or more hard disks are also connected in addition to the removable media device, the hard disk(s) will be able to record sound and load/save
.SNG files, but the removable media device will not be able to record sounds nor
load/save .SNG files. The removable media device will be usable only for operations such as Copy with Sound (page 52 of this manual) or Copy
(page 47 of this manual).
Parameters
Do not install a hard disk that was formatted on the TRINITY series into
another computer. Korg cannot guarantee the operation of such a disk.
Operation
After formatting has been executed, pressing the [COMPARE] key will not
restore the original state of the disk.
Connections for recording

Be sure that the power is turned OFF for all devices before you make connections.
Mixer
When using a mic to record,
connect it via a mixer.
OUTPUT
INPUT
Effect device
INPUT
OUTPUT
When recording a guitar that has active pickups,

you can connect it directly. However a passive
guitar (i.e., without a built-in preamp) should first
be passed through an effect device.
SCSI
INPUT
Hard Disk
S/P DIF OUT
Headphones
DAT
Connect a digital recording device (DAT etc.)

whose sampling frequency is 48 kHz.
Powered monitor speakers etc.
Sources that are input to the ANALOG IN 1 jack will be recorded on audio
track 1 or 3. Sources that are input to the ANALOG IN 2 jack will be recorded
on audio track 2 or 4.
Sources that are input to the S/P DIF IN connector will be recorded with the left
channel on audio track 1 or 3, and the right channel on audio track 2 or 4. Use a
commercially available video cable to make connections.
When turning on the power, turn on each device in sequence from the connected devices TRINITY.
When turning off the power, turn off each device in sequence from the TRINITY
connected devices.
Never turn off the power while the hard disk is being accessed (e.g., while
the LED indicator of the hard disk is lit).
Introduction
Song settings
1 Access the Sequencer mode P1 tab 5 page (ATrkRec).
2
4
5
Operation
1
2 In the Song field, select a new song and assign a song name.
The display will ask Are You Sure? Press the OK button.
Select AT1AT4 for monaural recording, or AT1&2 or AT3&4 for stereo recording. Make sure that the audio track(s) selected here appear in the Audio Track
Display.
4 If you wish to hear the metronome while you record, set the Metronome setting to
On or Rec (to sound only during recording), and adjust the tab 7 page (Preference)
Metronome settings Precount, Output, and Level.
With a metronome Output setting of L, L+R, or R, the metronome sound will be
output from the headphone jack and from output jacks 1/L/MONO and 2/R.
With a metronome Output setting of Send 1, Send 1+2, or Send 2, the metronome sound will be output from output jacks 3 and 4.
Parameters
3 In the Track field, select the audio track(s) that you wish to record.
name, check the Take No. box.
7 If two or more hard disks are connected, execute the Page Menu Command Rec
HD Select and select the hard disk that will be used for recording.
If only one hard disk is connected there is no need to execute this command.
Appendix
5 In the Take field, specify the take name.

6 If you want to differentiate sounds by a number added to the end of the take
Checking the external input

Before you begin, go to Song settings (page 7 of this manual) and select an
audio track (AT1 for this example).
2
3
2 Select the Input Select item.

If you are recording from an analog device such as a guitar connected to the
ANALOG IN 1 or 2 jack, select Analog.
Input from the ANALOG IN 1 jack will be recorded on audio track 1 or 3.
Input from the ANALOG IN 2 jack will be recorded on audio track 2 or 4.
If you are recording from a digital device such as a DAT connected to the S/P
DIF connector, select Digital. In this case, make sure that the Global mode P2
System Clock setting is set to S/P DIF. If you are recording from a digital device,
proceed to step 6 .
If a digital signal containing a copy inhibit flag is input, the display will indicate
Copy Inhibit. The HDR-TRI is able to record a digital signal which contains the
SCMS (Serial Copy Management System) flag. However it will be recorded as
digital audio data without the SCMS flag.
When digitally recording from copyrighted audio material such as a commercial DAT tape, you must be sure to obtain permission. Otherwise, you
must use non-copyrighted material. Korg will take no responsibility for
the consequences of any copyright violation which you may commit.
Input from the S/P DIF connector will be recorded with the left channel of the
source on audio track 1 or 3, and the right channel on audio track 2 or 4.
It is not possible to record a sampler or CD with a sampling frequency
other than 48 kHz via the S/P DIF connector. If you wish to record from
such a sampler or CD, use the ANALOG 1 or 2 jacks.
When recording vocals, pass the signal through a mixer and set this to 10 dBu
or +4 dBu. When recording a guitar that has active pickups, or a passive-type
guitar through an effect unit, set this to 30 dBu. However the input level will
depend on the characteristics of the connected device, or on the loudness of the
vocalist, the guitar playing technique, etc., so use the following table only as a
general guideline.
Example of connected device
30 dBu
Guitar
10 dBu
Consumer audio equipment such as CD player
+4 dBu
Introduction
3 Set the Input Level setting to a level appropriate for the connected device.
Professional audio equipment and keyboards
Operation
4 At this point, set the Rec Level fader to 0.0.

5 Play the connected guitar or other source.
The Rec Level meter will light, allowing you to confirm that an external audio
signal is being received. If the level meter is not responding, check the Input
Select setting, connections, cables, and the connected devices once again.
If the Input Level indicates Overload, the input level is too high. If this
occurs, set the Input Level to the next higher level.
6 Using the fader at the right of Rec Level, adjust the recording volume so that the
The volume that is output from external monitor speakers is determined

by the combination of the Rec Level and the tab 6 page (MixA14) channel
Volume. Also, there will be no output if the Pan settings are OFF for the
various channels in the tab 6 page (MixA14). If the level meter is moving
but you hear no sound, make sure that the volume is raised and that Pan is
not set to OFF.
If the sound is distorted even though the Input Level does not indicate
Overload, or the Rec Level indicate Over, access the tab 6 page (MixA 14)
and adjust the volume downward. A volume setting of 0 is , 100 is 0 dB,
and 127 is +127 dB.
Appendix
The output volume will be affected by this setting, so if you have connected external monitor speakers, etc., lower their volume before adjusting this setting.
Parameters
level meter does not rise all the way.
Recording
Recording
Recording an audio track
When recording an audio track, it is not possible to select Rec as the
Tempo Mode. If you wish to record tempo changes on the Master track,
select a MIDI track or MIXER REC in 1-4d: Track. Even when the Tempo
Mode is manual, do not modify the Tempo setting during recording.
1 Perform the procedure Settings for recording (page 310 of this manual).
2 Access the Sequencer mode P1 tab 7 page (Preference).
3 In the Recording Setup item, select the recording method.

If you are recording for the first time, select Overwrite.
4 Press the [REC/WRITE] key.

In 1 or 2 seconds you will enter record-ready mode, and the [START/STOP] key
LED will blink.
5 Press the [START/STOP] key.

Recording will begin.
6 To end recording, press the [START/STOP] key.

If you play the keyboard while an audio track is selected in 15: Track,
the settings (MIDI channel, Program, Track Status etc.) of the last-selected
MIDI track will be used.
10
Recording
Introduction
Recording a guitar in stereo on tracks 3 and 4

while listening to audio tracks 1 and 2
1 Use the procedure of Recording an audio track to record onto audio tracks 1
and 2.
2 Connect your guitar to a stereo-output effect device.

3 Connect the stereo-output effect device to the ANALOG IN 1 and 2 jacks.

The input to the ANALOG IN 1 jack will be recorded onto audio track 3, and the
input to the ANALOG IN 2 jack will be recorded onto audio track 4.
Operation
4 In the Track setting, select AT3&4.
Parameters
5 In the Input Select setting, select Analog.

6 In the Input Level setting, select 30 dBu.
the way.
If the Input Level indicates Overload, the input level is too great. If this occurs,
select the next higher setting for Input Level.
8 Press the [RESET] key to return to the beginning of the song. Press the [REC/WRITE]
key and then (after making sure that the [START/STOP] key LED is blinking) press
the [START/STOP] key.
Recording will begin. While listening to audio tracks 1 and 2, play your guitar
and record it on audio tracks 3 and 4.
9 To stop recording, press the [START/STOP] key.
The Compare function

If you press the [COMPARE] key, the TRINITY will return to the state it was in
before recording began (this is referred to as the Compare function). Press the
[COMPARE] key once again, and the recorded data will reappear.
11
Appendix
7 Play your guitar, and adjust the Rec Level so that the level meter does not rise all
Playback
Playback
Playing back the track(s) you recorded
1 Press the [RESET] key to return to the beginning of the song.
2 Press the [START/STOP] key.
The audio that was recorded will be played back.
Adjusting the pan or volume balance of the tracks

You can adjust the pan and volume of each track so that the recorded tracks are
played back in an appropriate balance. You can also use the equalizer to adjust
the tone of each track.
1 Access the Sequencer mode P1 tab 6 page (MixA14).
2 Set the Mix Audio Track Mode to MANUAL for the audio tracks that have already
been recorded.
3 Press the [RESET] key to return to the beginning of the song, and press the [START/
STOP] key.
Playback will begin.
4 Use the Pan/Volume settings to adjust the pan and volume of each track, and use
EQ to adjust the tone.
5 When you are finished, press the [START/STOP] key.
12
Recording mixer events

You can record pan, volume and equalizer settings as mixer events on the audio
track. The audio track will be played back according to the Pan/Volume, EQ,
and Send 1/2 settings that were recorded.
1 Use the procedure Recording an audio track to record an audio track.

3 In Recording Setup, specify the recording method for mixer events.
Introduction
Playback
When recording mixer events, select Overwrite.

Alternatively, you may use Auto Punch-In or Manual Punch-In to specify the
measures of the area in which recording will take place.
Operation
4 Access the tab 6 page (MixA14).

5
5 For the Track selection, select MIXER REC.

6 For the audio track on which you want to record mixer events, set the Mix Audio
Parameters
Track Mode to WRITE.
7 Press the [RESET] key to return to the beginning of the songpress the [REC/WRITE]
key and then (after making sure that the [START/STOP] key, LED is blinking) press
Recording will start.
8 While listening to the song, adjust EQ, Send 1/2, and Pan/Volume for the audio
track on which you want to record mixer events.
If you execute the page menu command Volume Pairing, adjusting the volume of one channel in a stereo pair will simultaneously adjust the volume of the
other channel.
13
Appendix
For audio tracks on which you do not want to record mixer events, set the
Mix Audio Track Mode to READ or MANUAL.
Re-recording
Re-recording
This section explains the procedure for re-recording part of a previouslyrecorded audio track.
If you wish to re-record the entire track, select Overwrite, and record using the
procedure Recording an audio track.
Using the rehearsal function

2 In the Track setting, select the audio track that you wish to edit.
3 For Recording Setup, select Auto Punch In.
4 Specify the area of measures that you wish to edit.
5 Access the tab 5 page (ATrkRec).
6 Check the Rehearsal check box.
7 Output sound from the instrument, etc. that you are recording, and adjust the
Input Level and Rec Level.
8 Check the Monitor Mode check box to set Auto Input ON.
When Auto Input is ON, you will be able to monitor the external input between
the punch-in and punch-out points, and at other times you will be able to monitor the previously-recorded sound. For example if you have set punch-in at 005
(measure 5) and punch-out at 008 (measure 8), you will be monitoring the previously-recorded sound for the first four measures, and will monitor the external
input sound during measures 5 through 8.
9 Press the [REC/WRITE] key and then (after making sure that the [START/STOP] key
LED is blinking) press the [START/STOP] key.
Simulated recording will start (nothing will actually be recorded). Between the
punch-in and punch-out points, you can practice the phrase that you intend to
record.
Using auto punch-in recording to edit

2 In the Track setting, select the audio track that you wish to edit.
3 For Recording Setup, select Auto Punch In.
4 Specify the area of measures that you wish to edit.
5 Access the tab 5 page (ATrkRec).
6 Un-check the Rehearsal check box.
If you wish to rehearse the punch-in, check the box.
7 Output sound from the instrument, etc. that you are recording, and adjust the
Input Level and Rec Level.
8 Press the [REC/WRITE] key and then (after making sure that the [START/STOP] key
LED is blinking) press the [START/STOP] key.
Recording will start. Play between the punch-in and punch-out points to rerecord the desired phrase.
When auto punch in recording is performed with Auto Input ON, approximately 0.5 seconds will be required from when the Punch Out point is reached
until the track playback sound can once again be monitored. (The audio for this
14
Editing
portion of track has not been lost.)
Introduction
Editing
Creating repetitions of the same phrase
1 Record using the procedure Recording an audio track.
2 Access the Sequencer mode P5 tab 3 page (Atrk Edit).
Operation
In the Track setting, select the audio track that you wish to edit.
In the Start Measure field, specify the copy destination.
Press the page menu command Copy Measure.
In the dialog box, make settings for Song, A.Track, and Measure Start/End to
specify the phrase that you wish to re-use, and then press the OK button.
The phrase of the area you specified here will be copied to the measure of the
track that you specified in step 4 .
7 Repeat steps 4 6 .
8 Press the [RESET] key to return the current location to the beginning of the song,
and then press the [START/STOP] key to listen to the playback.
Track bouncing (ping-pong recording)

Heres how to bounce (i.e., combine or ping-pong) audio tracks 1, 2 and 3 to
audio track 4. Because the TRINITY can bounce tracks in the digital domain,
you can perform this operation any number of times without degrading signal
quality.
1 In the Sequencer mode, set Track to AT4(R).

2 In the Sequencer mode P1 tab 6 page (MixA14), set audio track 4 to a Volume of
0.
To be sure that audio track 4s volume stays at 0, set its Mix Audio Track Mode
to Manual.
3 In the Sequencer mode P1 tab 1 and 2 pages (Trk18, Trk916), set each MIDI
tracks Track PLAY/MUTE/REC setting to MUTE.
15
Appendix
3
4
5
6
Parameters
Editing
This way, only the audio tracks will be bounced. If you want to bounce the MIDI
tracks audio as well, see Bouncing MIDI tracks and audio tracks together
below.
4 Make the appropriate Volume, Panning, EQ and Send 1/2 settings for audio
tracks 1, 2 and 3.
Since you will be mixing these three tracks down to a single track, you will not
be able to change their mix at a later time. Be sure you are satisfied with the settings
you make at this point.
5 Set Pan to R127 for audio tracks 13.

The playback from audio tracks 13 will be output from the right channel of the
S/P DIF jack. This is necessary because audio tracks 2 and 4 record signals from
the right channel (you selected audio track 4 as the recording track in the previous step). Audio tracks 1 and 3 record signals from the left channel. If you had
chosen to bounce to audio track 1 or 3, you would need to set Pan to L000 for
this step.
6 Connect the S/P DIF OUT connector to the S/P DIF IN connector.
Use a commercially available video cable to make connections.
7 Set the Global mode P2 System Clock setting to Internal.

8 Set the P1 tab 5 page (ATrkRec) Input setting to Digital.
9 Press the [RESET] key to return to the beginning of the song, press the [REC/WRITE]
Recording from audio tracks 1, 2, and 3 to audio track 4 will begin.
0 Disconnect the video cable from the S/P DIF OUT and IN connectors.
If the mixer volume is raised when the S/P DIF connectors are connected,
oscillation may occur. For this reason, the S/P DIF OUT and IN connectors
should not be connected to each other except while bouncing tracks.
Bouncing MIDI tracks and audio tracks together

The TRINITY also lets you bounce MIDI tracks and audio tracks together, down
to audio tracks. Bouncing tracks in this way allows you to conserve MIDI tracks
and polyphony. For example, you can bounce MIDI tracks 116 plus audio
tracks 1 and 2 to audio tracks 3 and 4, preserving the stereo mix you have created.
The procedure is basically the same as outlined in the previous section (ignore
steps 3 and 5 ). Make the appropriate Volume, Panning, EQ and Send 1/2 settings for audio tracks 1 and 2 and the MIDI tracks (you can also set the MIDI
tracks insert effects). In step 2 , set the Volume of audio tracks 3 and 4 to 0. In
step 1 , set Track to AT3&4.
Applying master effects

1 Access the Sequencer mode P1 tab 6 page (MixA14).
2 Use Send 1/2 to adjust the send levels (the amount of signal sent to the master
effects) for each track.
Send 1 is the input to the modulation-type master effect (effect 1).
Send 2 is the input to the reverb-type master effect (effect 2).
With a setting of 064, the send level to the master effect will be 50 percent.
3 Access the P8 tab 1 page (Master FX).

To use a master effect, select the effect and turn it ON, and raise the return 1 and
16
2 levels.
If you check the check box located at the left of the display, the right side output
of effect 1 will be sent to effect 2, and effects 1 and 2 will be mixed. Refer to the
Parameter Guide for details on the P8 tab 1 page (Master FX), and to the Effect
Guide for an explanation of the settings of the master effects.
Creating a song in conjunction with the MIDI

sequencer
Introduction
Creating a song in conjunction with the MIDI sequencer
Operation
This section explains how to record a vocal on audio track 1 to the accompaniment of the MIDI sequencer.
Recording the vocal

2
3
4
Parameters
5
6
1
2 In the Song field, select the song that will provide the accompaniment.
3 For the Track setting, select the desired audio track (AT1 in this example).
Make sure that the Audio Track Display shows the selected audio track.
hear it only during recording), and make Metronome settings for Precount, Output, and Level in the tab 7 page (Preference).
With a metronome Output setting of L, L+R, or R, the metronome sound will be
output from the headphone jack and from output jacks 1/L/MONO and 2/R.
With a metronome Output setting of Send 1, Send 1+2, or Send 2, the metronome sound will be output from output jacks 3 and 4.
5 In the Take field, assign a take name.

6 If you want a number to be added at the end of the take name to distinguish
takes, check the Take No. box.

8 Set the Input Select to Analog.
9 For the Input Level, select a level appropriate for the device that is connected (10
dBu) for this example, and sing into the mic while you adjust the Rec Level so that
the meter does not go all the way.
If the Input Level indicates Overload, the input level is too high. If this occurs,
17
Appendix
4 If you wish to hear the metronome as you record, set Metronome to On or Rec (to
Creating a song in conjunction with the MIDI sequencer
set Input Level to the next higher setting.
Recording
0 Press the [RESET] key to return to the beginning of the song, press the [REC/WRITE]
Recording will start. Sing into the mic while listening to the accompaniment of
the MIDI sequencer.
A When you finish recording, press the [START/STOP] key.
Adjusting the balance and equalizer for the monitor output

Heres how to adjust the pan, volume and EQ of the vocal that was recorded on
the audio track. To make adjustments for the MIDI sequencer, use the tab 3 or 4
page (Mix 18 or Mix 916).
B Access the tab 6 page (MixA14).

C Set the Mix Audio Track Mode to MANUAL for the channel that you wish to adjust
(channel 1 in this example).
D Press the [RESET] key to return to the beginning of the song, and then press the
[START/STOP] key.
The song with vocals will begin playing back.
E Use Pan/Volume to adjust the pan and volume of channel 1 to create an appropriate balance of sound in the monitor output. Use EQ to adjust the tone.
A Pan setting of C064 will produce the impression of singing from center stage.
Using effect processing

If you wish to apply effects to give spaciousness to the vocal, use the Send
parameters and the Master Effects of P8 to make settings for the effect types
and the amount of the effects.
F With the recorded song playing back, set Send to about 64.
G Access the P8 page.
Select the effects in the tab 1 (Master FX) page (make detailed effect settings in
the tab 2 and tab 3 pages as necessary), and raise the Return parameters to
adjust the mix with the original sound.
To adjust the depth of the effects, use the master effect parameters to make settings for each effect, and use the P1 Send and P8 Return parameters to adjust the
sends and returns.
Recording mixer events

Heres how to record pan, volume, send, and equalizer mixer events.
H Access the Sequencer mode P1 tab 5 page (MixA14).

For the Track item, select MIXER REC.
I Set the Mix Audio Track Mode to WRITE for the channel that you wish to record
(channel 1 for this example).
J Press the [RESET] key to return to the beginning of the song, press the [REC/WRITE]
The song will playback.
K Adjust the Pan/Volume, Send, and EQ of the channel whose Mix Audio Track
Mode was set to WRITE (channel 1 for this example).
Your adjustments will be recorded as mixer events.
18
Saving/loading recorded data
When playing back the song, set the Mix Audio Track Mode to READ for channel 1. Playback will be controlled according to the mixer events that were
recorded.
Saving/loading recorded data

Saving song data to a hard disk
Introduction
L When you are finished, press the [START/STOP] key.
Operation
1 Access the Disk mode tab 2 page (Save).

3
1
2 In the Drive Select box, select the hard disk on which you want to save the data.
As necessary, use the Open button and the Up button to move through the
directory hierarchy, and select the saving destination.
Parameters
Song data that includes an audio track(s) cannot be saved to a floppy disk.
3 Execute the page menu command Save Song.
Appendix
Loading data from a hard disk

1 Access the Disk mode tab 1 page (Load).
4
3
19
Using a recorded sound more than once in the same .SNG file
2 In the Drive Select box, select the hard disk that contains the data you wish to
load.
3 In the directory window, specify the data that you wish to load.
As necessary, use the Open or Up buttons to move through the directory hierarchy, and specify the data to be loaded.
4 Execute the page menu command Load Selected.

The dialog box that appears when Load Selected is executed will depend on the
type of data that is being loaded. Follow the instructions given in the dialog box
that appears. For details on the various dialog boxes and the procedure, refer to
the explanations for the page menu commands in 11: Load of Disk mode in
the Parameter Guide.
Using a recorded sound more than once in the

same .SNG file
Creating different arrangements using the same
vocal
After selecting a new song in Song mode, select the Copy from Song function
from the page menu of Sequencer mode P1 to copy the song containing the data
you wish to use to a new song. Then re-record the MIDI tracks, etc. to create a
new accompaniment.
Using the same sound more than once

Here is a useful way to use a recorded sound effect more than once.
For example, suppose that you are using song 19 as a library song that contains various sound effects recorded at different locations.
To use a sound from this library song, use the P5 tab 3 page (ATrkEdit) page
menu command Copy Measure to copy sounds to the desired location in the
song that you are creating. If you need to make fine adjustments to the location
of the sound, use the P5 tab 3 page (ATrkEdit) page menu command Audio
Event Edit.
If you use the Copy Measure command to copy all sounds recorded in other
songs to a library song, these sounds will be ready for immediate use if they
are ever needed later; you will not have to re-record them.
Collecting sounds in a library song in this way also provides a backup of the
sounds.
In the Copy Measure dialog box, specify the Start Measure and End
Measure of the copy source, and execute the copy command. At the copy
destination, the number of measures specified in the dialog box will be
overwritten. For example if measures 14 were specified as the copy
source, the four measures 14 will be overwritten at the copy destination.
However if Copy Measure is executed between songs that have a different Tempo setting, the playback time will differ even if the number of
measures is identical, meaning that the copied data may not fit into the
specified number of measures, or that a gap may occur at the end of the
measures.
20
3. Parameters
This manual explains the functions which are newly added when the HDRTRI hard disk recorder option is installed. For the parameters whose functions remain unchanged, refer to your Parameter Guide, Basic Guide, and
Effect Guide.
Introduction
Sequencer P1
15: Audio Track Rec

Here you can make basic settings for recording onto the audio tracks. Since realtime recording is done according to the recording method selected in 17: Preference, make settings for those parameters as well. Detailed editing after
recording (non-realtime editing) can be performed in 53: Audio Track Edit.
15d
Operation
Sequencer P1
Page Menu
15c
Parameters
15e
15f
15g
15h
15D
15i
15j
15k
15l
15c: Tempo/Tempo Mode

Tempo Mode
With a setting of Manual, the tempo data in the master track will be ignored,
and playback will play at the Tempo setting.
Never modify the Tempo setting while recording an audio track, since this
will prevent proper recording.
With a setting of Auto, the tempo during playback will change according to the
tempo data in the master track.
It is not possible to select Rec in this mode. If you wish to record tempo changes
to the master track, go to 15d: Track and select a MIDI track or MIXER REC.
21
Appendix
15m
Sequencer P1
15d: Track
[T01...16, MTR, AT1(L), AT2(R), AT3(L), AT4(R),

AT1&2, AT3&4, MIXER REC]
Select the track that you wish to record.

When the HDR-TRI is installed, you will be able to select audio tracks AT1(L),
AT2(R), AT3(L), AT4(R), AT1&2 or AT3&4, and MIXER REC in addition to the
MIDI tracks T0116 and the MTR (Master Track) that were previously available.
When T0116 are selected, you can record onto the selected MIDI track. Basic
settings for recording a MIDI track and settings that determine how the notes
will be sounded and output are made in 11: Track Play/Rec14: Mixer
(Track 916), and the recording method is selected in 17: Preference.
When a MIDI track is selected, playing the keyboard and operating the controllers will cause the internal tone generator to sound with the settings (program
and level, etc.) of the MIDI track that you select here (if the Track Status is INT
or BOTH). In addition, other MIDI tracks with the same MIDI channel will also
sound (if the Track Status is INT or BOTH). Furthermore, messages will be
transmitted on the MIDI channels specified for those MIDI tracks (if the Track
Status is EXT or BOTH).
If you play the keyboard while an audio track is selected in 15: Track, the settings (MIDI channel, Program, Track Status etc.) of the last-selected MIDI track
will be used.
When realtime recording a single track, the musical data will be recorded onto
the MIDI track you select here.
When realtime recording multiple tracks, you can specify in 11i: PLAY/
MUTE/REC whether recording will occur for each MIDI track.
Select MTR when using 51: Track Edit to edit the master track.
If AT1AT3&4 is selected, you can record onto the selected audio track(s). When
AT1&2 or AT3&4 are selected, you can record a stereo pair of audio tracks. The
audio track(s) selected here will also appear in the 15l: Rec Audio Track Name
Display.
Here you can make basic settings for recording the audio track(s), set the output
level and EQ settings, etc. in 16: Mix Audio Track 14, and select the recording method in 17: Preference.
Select MIXER REC when you wish to record mixer events using 16: Mix
Audio Track 14.
The audio track name displayed here is set in 54: Audio Track Name, and the
MIDI track name is set in 52: Track Name. However if AT1&2 or AT3&4 are
selected, the audio track name will not be displayed.
This parameter is displayed in all pages 11: Track Play/Rec through 17:
Preference, and can be modified from any page.
15e: Meter/Metronome/Resolution/Multi Rec/Remove Data

Multi Rec
If this is checked, multi-track recording mode will be used, but the audio tracks
cannot be recorded.
If this is un-checked, single-track recording mode will be used. Un-check this
when you wish to record audio tracks.
22
Sequencer P1
If you re-assign the take name here, the incremented number will begin from 00.
Also, if in 15g: Take Number you change the number to a value other than
00, the count-up will begin from that number.
If you wish to change the sound name that was recorded, use the Trimming an
audio event command (page 39 of this manual) that appears when you press
the Trim button in 53J: Audio Event Edit.
15g: Take Number

If this is checked, the number shown at right will be automatically added to the
take name (up to 13 characters) that was assigned in 15f: Take.
This number will be incremented each time you record using the same take
name.
If you re-assign the take name in 16f: Take, the incremented number will
begin from 00. Also, if you change the number to a value other than 00, the
count-up will begin from that number.
Operation
When you begin recording, a sound will be

created and a name assigned to it. The sound
Take name
(for stereo)
name will consist of the take name you specify
Sound name = first 13 characters of Take name + 2 digit
here plus the incrementing number. When
number + 1 character L/R
recording in stereo, an L or R will be added.
The sound name will be displayed during the event edit or sound trim operations performed in 53J: Audio Event Edit.
Parameters
Specify the name of the take that you are about to record.
Press the text edit button, and the rename page will appear. ( Basic Guide
page 6). Up to 13 characters can be used here.
If you wish to append a number at the end of the take name to manage your
takes, check 15g: Take Number. When you stop recording, the number will
be automatically incremented, and added to the take name (for the next recording).
Introduction
15f: Take
15h: Rehearsal
If this is checked, recording operations will be simulated (recording will not
actually take place).
Monitoring during rehearsal will depend on the selection in 15m: Monitor
Mode Select. When Auto Input is ON, you will be able to monitor the external
input between the punch-in and punch-out points, and at other times you will
be able to monitor the previously-recorded sound. For example if you have set
punch-in at 005 (measure 5) and punch-out at 008 (measure 8), you will be monitoring the previously-recorded sound for the first four measures, and will monitor the external input sound during measures 5 through 8.
15i: Input Select
[Analog, Digital]
Select either Analog or Digital as appropriate for the signal that is being input.
When Digital is selected, please input a digital signal at a sampling frequency of
23
Appendix
If this is un-checked, an incremented number will not be added to the take

name of the sound that you are about to record.
Sequencer P1
48 kHz.
If a digital signal containing a copy inhibit flag is input, the display will indicate
Copy Inhibit. The HDR-TRI is able to record a digital signal which contains the
SCMS (Serial Copy Management System) flag. However it will be recorded as
digital audio data without the SCMS flag.
When a signal with a sampling frequency of 48 kHz is being input, the display
will indicate 48 kHz. For other sampling frequencies, the display will indicate
FsError, and recording will not be performed correctly.
Also, when recording digitally, you must set the Global mode System Clock setting of 11d: MIDI Clock/System Clock to S/P DIF so that the TRINITY will
use the S/P DIF clock of the external device.
When recording from a CD or a sampler whose sampling frequency is other
than 48 kHz, use the ANALOG IN 1 or 2 jacks and select Analog for this setting.
15j: Input Level
[+4 dBu, 10 dBu, 30 dBu]
This controls the gain amp that adjusts the level of the analog input.
If the input level is higher than this Input Level and the input is distorted (clipping), the display will indicate Overload.
This parameter will be available when Analog is selected in 15i: Input Select.
When recording vocals, route the signal through a mixer and set this to either
10 dBu or +4 dBu. Set this to 30 dBu when recording a guitar that has active
pickups, or when recording a guitar that has passive pickups routed through an
effect device. However input levels will depend on the characteristics of the
equipment that is connected, on the loudness of the vocalist, and on playing
technique, etc., so use the following table merely as a guideline.
Example of connected device
30 dBu
Guitar
10 dBu
Consumer audio equipment such as CD player
+4 dBu
Professional audio equipment and keyboards
15k: Rec Level
[...+18 dB]
Adjust the level for recording.

Adjust the fader so that the level meter does not rise all the way.
The output volume will be affected by this setting, so if you have connected
external monitor speakers, etc., lower their volume before adjusting this setting.
If an audio track is not selected in 15d: Track, there will be no output
from the monitor even if the level meters are up.
15l: Audio Track Name Display

This indicates the audio track selected in 15d: Track.
If T01...T16, MTR, or MIXER REC is selected in 15d: Track, this will be displayed as OFF. It will likewise be displayed as OFF during multi-track recording
of MIDI tracks.
24
Sequencer P1
Auto Input
Audio
track(s)
selected
by Track
Audio
tracks not
selected
by Track
Stopped
Playing
During Punch Rec
During
Overwrite
Rec
...In
In...Out
Out...
ON
Line
Track
Line
Track
Line
Track*
OFF
Line
Line
Line
Line
Line
Line
ON
Track
Track
Track
Track
Track
Track
OFF
Track
Track
Track
Track
Track
Track
* When auto punch in recording is performed with Auto Input ON, approximately 0.5 seconds will be required from when the Punch Out point is
reached until the track playback sound can once again be monitored. (It is not
the case that the track audio in this portion has been lost.)
Operation
Audio track monitoring (Line: external input, Track: track playback)
Parameters
This selects Auto Input ON/OFF.

Audio tracks that are selected in 1-5d: Track will be monitored differently
than audio tracks that are not selected. (Refer to the table below.)
If this is checked, Auto Input will be ON. During auto/manual punch in recording, monitoring will be switched automatically for the audio tracks selected in
the Track page: the external input will be monitored during the measures being
recorded, and the track playback will be monitored before and after these measures.
For audio tracks which are not selected in the Track page, the track playback
will always be monitored.
If this is not checked, Auto Input will be OFF. Audio tracks selected in the Track
page will always monitor the external input.
For audio tracks which are not selected in the Track page, the track playback
will always be monitored.
Introduction
15m: Monitor Mode Select
15D: Rec HD Select

Select the hard disk on which recording will take place.
The amount of time available for recording (Free Time) will also be displayed
here. Since the amount of recorded sound will gradually increase, we recommend that you periodically use the Disk mode command 14F: Delete Unused
Sound to organize the sound and maintain the Free Time space.
1 When you select Rec HD Select, the dialog

box at right will appear.
2 Select the hard disk for recording: ID0ID6.

Keep in mind the amount of Free Time as
you select a hard disk.
3 To execute Rec HD Select, press the OK button. To cancel without executing, press the
Cancel button.
25
Appendix
Page Menu Command
Sequencer P1
16: Mix Audio Track 14

Here you can make basic settings for recording audio tracks, and make mixer
event settings for each track. Mixer events are recorded according to the recording method selected in 17: Preference, so you will need to set those parameters as well. Editing of mixer events can be performed in 53: Audio Track
Edit.
For details on the basic settings for recording an audio track, refer to 15:
Audio Track Rec.
Page Menu
Information for the

selected audio track
16f
16D
16g
16E
16h
16i
16j
16f: EQ (Equalizer)
This adjusts the tone of the audio signal that is output from the 1/L/MONO
and 2/R output jacks (and the S/P DIF output).
Depending on the selection in 16j: Mix Audio Track Mode, it may not be possible to modify this parameter. Refer also to 16j: Mix Audio Track Mode.
H (High EQ)
[15...0...+15]
Adjusts the level of the high frequency range (Fc= 10 kHz) of the audio track
playback.
L (Low EQ)
[15...0...+15]
Adjusts the level of the low frequency range (Fc= 100 Hz) of the audio track
playback.
16g: Send1/Send2
[0...127]
Adjusts the send levels to the master effects (left is Send 1, right is Send 2).
16h: Pan (Panpot)
[OFF, L000...C064...R127]
Specifies the panning to the 1/L/MONO and 2/R output jacks (and the S/P DIF
output).
With a setting of OFF, there will be no output to the 1/L/MONO and 2/R output jacks (or the S/P DIF output).
26
Sequencer P1
[0...100...127]
Adjusts the volume of each audio track.

A setting of 0 is , 100 is 0 dB, and 127 is +12 dB.
16j: Mix Audio Track Mode
[MANUAL/READ/MUTE/SOLO/WRITE]
Introduction
16i: Volume
When a track is played back with a setting of MUTE, the muted audio track will
not be heard.
When a track is played back with a setting of SOLO, all other audio tracks will
be set to MUTE, and you will hear only the sound of the selected audio track.
Audio tracks which are set to SOLO will be played back according to the mixer
events which were recorded. At this time, even if you adjust EQ, Send, Pan, or
Volume during playback, the setting will change to the setting of a mixer event
when the location of that mixer event is reached.
Two or more audio tracks can be set to SOLO, but the modes which can subsequently be selected for each audio track will differ as follows, depending on
whether only one, or two or more audio tracks were set to SOLO.
When SOLO is selected for one audio track
Parameters
When a track is played back with a setting of READ, the mixer events that were
recorded will be played back. Even if you adjust EQ, Send, Pan, or Volume during playback, the setting will change to the setting of a mixer event when the
location of that mixer event is reached. (If there are no mixer events, the parameters can be set in the same way as for MANUAL.)
Operation
When a track is played back with a setting of MANUAL, the mixer events that
were recorded will be ignored, and EQ, Send, Pan, and Volume will be set manually.
MANUAL, READ, MUTE, SOLO, WRITE
MUTE tracks
SOLO, MUTE
If the SOLOED audio track is switched to a different mode, audio tracks which
are MUTED will switch to the same mode as was selected for the previously
SOLOED audio track.
For example if the SOLOED audio track is switched to MANUAL, the MUTED
tracks will also be switched to MANUAL. Similarly, if the SOLOED audio track
is switched to WRITE, the MUTED tracks will also be switched to WRITE.
So be careful not to accidentally record over existing tracks.
When SOLO is selected for two or more audio tracks
Selectable modes
SOLO tracks
SOLO, MUTE
MUTE tracks
SOLO, MUTE
Select WRITE to record mixer events. In order to record mixer events, select
Mixer Rec as the Track setting, and select WRITE here. Then begin recording
(simultaneously press the [REC] key and the [PLAY] key). The various audio
track parameters that were set in this tab page will be recorded as mixer events
in the range of measures specified by Recording Setup in 17: Preference. Dur-
27
Appendix
Selectable modes
SOLO tracks
Sequencer P1
ing recording, you can adjust EQ, Send, Pan, and Volume and the changes you
make will be recorded. By changing this setting to READ and then playing back
the song, EQ, Send, Pan, and Volume settings will change according to the mixer
events that were recorded.
Mixer events can also be edited individually in 53B: Automation Edit.
WRITE can be selected only if MIXER REC has been selected in 15d:
Track.
If after using WRITE you change from MIXER REC to another track, the Mix
Audio Track Mode of the audio track that was written will automatically
change to READ.
Page Menu Command

16D: Rec HD Select
This selects the hard disk on which recording will take place.
The Free Time (recordable time) will also be displayed.
For the procedure, refer to 15D: Rec HD Select.
16E: Volume Pairing

This links the volume of a pair of channels. (When you adjust the volume of one
channel, the volume of the other channel will change automatically.)
1 When you choose Volume Pairing, the dialog box at right will appear.
Check the check box for the pair(s) of channels that you wish to link.
2 To execute Volume Pairing, press the OK
button. To cancel without executing, press
the Cancel button.
28
Sequencer P1
Introduction
17: Preference
Here you can make overall settings for the entire song, recording settings for
MIDI tracks, audio tracks, and mixer events, and settings for playback.
Page Menu
Operation
17h
17h: Recording Setup
When you record using Overdub, newly recorded audio tracks will be overwritten over the previously recorded data, just as with Overwrite recording. However when mixer events are recorded, they will be added to the previously
existing data.
Recording is not possible when Loop is selected.
As when recording MIDI tracks, you will first use Overwrite to record the data.
If you wish to use realtime recording to modify previously recorded data, use
Auto/Manual Punch In. To modify individual events (for example to insert part
of an orchestra hit), you can use the editing commands of 53J: Audio Event
Edit to trim (page 39 of this manual), move, or copy the data.
29
Appendix
When you record using Overwrite, the new data will be recorded over (i.e., will
replace) the previously recorded data.
When Overwrite recording a MIDI track, the musical data that was previously
recorded in measures later than the measure at which recording began will be
erased. However this is not the case for audio tracks; the previously recorded
data will be overwritten only in the measures which are actually re-recorded,
and the previously recorded data in subsequent measures will remain.
Parameters
Use the radio buttons to select the realtime recording method.
Sequencer P2
Sequencer P2
25: Audio Track parameter (Audio Track 14)
Here you can specify the song name, the scale used by MIDI tracks, and the
delay for each audio track.
Page Menu
Data for the selected
audio track
25c
25D
25c: Delay
[0...255 samples/0...5 ms]
Specify the time delay from the location of an audio track event until when the
sound is heard from the TRINITY during playback.
This can be set in units of either samples or milliseconds.
Normally you will leave this set at 0.
Page Menu Command

25D: Rec HD Select
Select the hard disk on which recording will take place.
The Free Time (remaining time for recording) will also be displayed here.
For the procedure, refer to 15D: Rec HD Select.
30
Sequencer P5
53: Audio Track Edit
Here you can edit audio events and mixer events of a previously-recorded audio
track.
Introduction
Sequencer P5
Page Menu
53d
53F
Audio data display

(selected track is highlighted)
53H
53C
53I
53D
53J
53E
Master Track
53i
Upper line: audio events @ @
53d: Track
Lower line: mixer events @ @
No events
[T01...16, MTR, AT1(L), AT2(R), AT3(L), AT4(R),

AT1&2, AT3&4, MIXER REC]
Select the track that you wish to edit (or the copy destination track).
When the hard disk recorder option is installed, you will be able to select audio
tracks AT1(L), AT2(R), AT3(L), AT4(R), AT1&2 or AT3&4, and MIXER REC, in
addition to the MIDI tracks T0116 and the MTR (Master Track) which were
previously available.
Parameters
Audio Track1
Operation
53G
53B
Since this tab page is for editing audio tracks, it will not be possible to edit
T0116 or MTR even if you select them. To edit MIDI tracks or the master
track, use 51: Track Edit.
Conversely, it is not possible to use 51: Track Edit or 52: Track Name
to display or edit audio tracks.
Select MIXER REC when you wish to use 16: Mix Audio Track 14 to
record mixer events. After making your selection here, move to 16: Mix
Audio Track 14 and record.
53i: Start Measure/End Measure

Specifies the range of measures in the audio track that will be edited.
Start Measure
[1...999]
Specifies the first measure.
End Measure
[1...999]
Specifies the last measure.
31
Appendix
If you wish to edit audio events or mixer events, select AT1(L), AT2(R), AT3(L),
AT4(R), AT1&2, or AT3&4.
Sequencer P5
Page Menu Command

53B: Automation Edit
Here you can edit individual mixer events that were previously recorded. To
perform event editing on audio tracks, use 53J: Audio Event Edit.
1 In the tab 3 page, select an audio track that contains the mixer events you
wish to edit, and specify the Start Measure.
2 When you choose Automation Edit, the

dialog box at right will appear.
3 The Set Event Filter check boxes in the

Automation Edit dialog box allow you to
select the type(s) of data which will be
edited.
You can select Audio (Audio Event), EQ,
Send 1/2, Pan, and Volume data. Data
types whose check box is checked will
appear in the Automation Edit dialog box.
If you set the Track setting to AT1&2 or
AT3&4 in the tab 3 page, you can select
which track in the pair to edit.
Event editing of audio tracks is performed using 53J: Audio Event Edit.
(Even if the Audio box is checked, audio events will only be displayed here,
and cannot be edited.)
4 To move to the Automation Edit dialog box, press the OK button. To return
to the previous display, press the Cancel button.
When you press the OK button, a dialog box like the following will appear.
b: Location in measure
Index number
Value of event
c: Type of event
Audio event end location

(display only)
(measure, beat, clock)
a: Index
a: Scroll bar
b: Measure
A: Insert button
C: Copy button
B: Delete button
Execute button
D: Audition start/stop button
a: Specify measures or locations, etc. by selecting an index number, by using

the scroll bar, or by directly pressing an event.
b: You can move through the events by changing the measure or location values.
32
E:001.00.000...999.15.191 (display
only) (end of audio event: measure,
beat, clock)
Sound name (ex. Take01L)

(display only) (Audio event)
HiEQ
G: 15+15
(gain)
LoEQ
G: 15+15
(gain)
Send1
V: 0127
(value)
Send2
V: 0127
(value)
Pan
V: 0127
(value)
Volume
V: 0127
(value)
5 Press the appropriate button to make the desired edits as follows.

When you have finished editing mixer events and wish to return to the tab
page, press the Done button.
Operation
c: The following table shows the types of events and the possible values for
each type.
Introduction
Sequencer P5
Inserting a mixer event

Select a mixer event located where you wish to insert a new event, and press the
Insert button. A new mixer event will be inserted at the location of the selected
mixer event.
Moving a mixer event
Select the mixer event that you wish to move, and press the Delete button. Then
press the Insert button at the desired new location, and that mixer event will be
inserted.
Parameters
A: Insert button
Deleting a mixer event

Select the mixer event that you wish to delete, and press the Delete button.
The mixer event will be deleted.
C: Copy button
Copying a mixer event
Select the mixer event that you wish to copy, and press the Copy button. Then
press the Insert button at the desired new location, and that mixer event will be
inserted.
D: Audition Start/Stop button

Starting/stopping audition
When an audio event is highlighted, you can press the Audio Start/Stop button
to playback that audio event. During playback, you can press the button once
again to stop playback.
33
Appendix
B: Delete button
Sequencer P5
53C: Erase Audio Track

This command erases all playback data from the audio track specified in the tab
3 page.
1 In the tab 3 page, specify the audio track to

be erased.
2 When you choose Erase Audio Track, the

3 If you wish to erase the playback data of all

tracks including MIDI tracks, check All
Tracks.
If this is not checked, the audio track specified in the tab 3 page will be
erased.
4 To execute the Erase Audio Track command, press the OK button. To cancel
without executing, press the Cancel button.
53D: Copy Audio Track

This command copies playback data from the audio track specified in the dialog
box to the audio track specified in the tab 3 page.
Be aware that when you execute the Copy Audio Track command, the playback
data that was previously in the copy destination track will be erased.
1 In the tab 3 page, select the copy destination audio track.

2 When you choose Copy Audio Track, the
3 Specify the copy source track.

4 To execute the Copy Audio Track command, press the OK button. To cancel without executing, press the Cancel button.
53E: Erase Measure

This command erases specified measures of playback data from the track specified in the tab 3 page. You can specify the type of data that will be erased.
Unlike the Delete Measure command, executing the Erase Measure command
will not cause the playback data of subsequent measures to move.
1 In the tab 3 page, specify the audio track from which data is to be erased, and
the Start Measure and End Measure.
If MTR is specified as the track, the Kind item in 3 will change to Tempo.
2 When you choose Erase Measure, the dialog box at right will appear.
3 Use the Kind and All Track settings
together to specify the data that will be
erased. (Refer to the table on the following
page.)
The Kind setting lets you select the type of
data (All, Audio Event, Mixer Event, EQ,
Send1/2, Pan, Volume) that will be erased.
34
Sequencer P5
Checked
Un-checked
Audio events and mixer events of the
selected audio track
Audio Event
Audio events of audio tracks 14
Audio events of the selected audio track
Mixer Event
All mixer events of audio tracks 14
All mixer events of the selected audio

track
EQ
Equalizer events of audio tracks 14
Equalizer events of the selected audio

track
Send 1/2
Send 1/2 events of audio tracks 14
Send 1/2 events of the selected audio

track
Pan
Panpot events of audio tracks 14
Panpot events of the selected audio

track
Volume
Volume events of audio tracks 14
Volume events of the selected audio

track
All
Operation
MIDI tracks, master track, audio events

and mixer events of the audio tracks
Introduction
All Tracks
Kind
4 To execute the Erase Measure command, press the OK button. To cancel

Before Erase
After Erase
No data
Be aware that if this command is executed with All selected for Kind and
the All Tracks box checked, any control data in MIDI tracks which spans the
boundary of the erased and non-erased sections will be erased only in the
specified area. Also, erasing measures through which a note is held (i.e.,
measures falling within the duration of a note) will cause that note data to be
erased from subsequent measures as well.
Parameters
Example: If measures 23 are erased, measures 23 will be blank.
This command deletes specified measures of playback data from the track specified in the tab 3 page.
Unlike the Erase Measure command, executing the Delete Measure command
will cause the playback data of subsequent measures to move toward the beginning of the song to fill the gap.
1 In the tab 3 page, specify the audio track from which measures are to be
deleted, and the Start Measure and End Measure.
2 When you choose Delete Measure, the dialog box at right will appear.
3 If you wish to delete measures from all

tracks including the MIDI tracks, check the
All Tracks box.
If this box is not checked, measures will be
deleted from the audio track specified in
the tab 3 page.
4 To execute the Delete Measure command, press the OK button. To cancel
without executing, press the Cancel button
35
Appendix
53F: Delete Measure
Sequencer P5
Example: When measures 35 are deleted, measures 68 are moved forward.

Before Delete
After Delete
Example: When measures 2 and 3 (3/4 time) of track 2 are deleted, the measures that were at 4 and 5 are moved
forward, and their time signature will change to 3/4.
Track 1
1 (4/4)
2 (3/4)
3 (3/4)
4 (4/4)
5 (4/4)
Track 2
1 (4/4)
2 (3/4)
3 (3/4)
4 (4/4)
5 (4/4)
Track 2
1 (4/4)
2 (3/4)
3 (3/4)
Track 1
1 (4/4)
2 (3/4)
3 (3/4)
4 (4/4)
5 (4/4)
Before Delete
After Delete
If this command is executed with the All Tracks box checked in step 3 , the
playback data in the measures specified in the tab page will be deleted from
all tracks including the MIDI tracks and master tracks, and the time signature and tempo will also slide forward according to the number of measures
deleted.
Be aware that when this command is executed, any control data in MIDI
tracks which spans the boundary of the deleted and non-deleted sections
will be deleted only in the specified area. Also, deleting measures through
which a note is held (i.e., measures falling within the duration of a note) will
cause that note data to be deleted from subsequent measures as well.
53G: Insert Measure

This command inserts the number of measures specified in the dialog box into
the track specified in the tab 3 page. When the Insert Measure command is executed, the measures will be inserted at the location specified for the Start Measure. Playback data located after the inserted measures will slide toward the end
of the song to make room.
1 In the tab 3 page, specify the audio track into which measures will be
inserted, and the Start Measure.
2 When you choose Insert Measure, the dialog box at right will appear.
3 If you wish to insert measures into all

All Tracks box. Playback data located after
the inserted measures will play in the same
way as before.
If this box is not checked, measures will be inserted into the audio track
selected in the tab 3 page.
The playback data located after the insertion point will slide toward the end
of the song to make room, but be aware that the time signature and tempo
will not move.
36
4 For the Length field, specify the number of measures that will be inserted.
5 For the Meter* field, specify the time signature of the measures that will be
inserted.
6 To execute the Insert Measure command, press the OK button. To cancel

* If you want the time signature of the inserted measures to match the existing time signature, set this to **/**.
With a setting other than **/**, the time signature of the inserted measures
will change, and all tracks will be played with the specified time signature
for those measures.
Introduction
Sequencer P5
Track 1
1 (4/4)
2 (4/4)
3 (3/4)
4 (5/4)
5 (2/4)
Track 1
1 (4/4)
2 (4/4)
3 (3/4)
4 (5/4)
5 (2/4)
Track 2
1 (4/4)
2 (4/4)
3 (3/4)
4 (5/4)
5 (2/4)
Track 2
1 (4/4)
2 (4/4)
3 (3/4)
4 (5/4)
5 (2/4)
Before Insert
Two measures inserted
Track 2
1 (4/4)
2 (4/4)
3 (3/4)
4 (5/4)
5 (2/4)
Track 2
1 (4/4)
2 (7/8)
3 (7/8)
4 (5/4)
5 (2/4)
Track 1
1 (4/4)
2 (4/4)
3 (3/4)
4 (5/4)
5 (2/4)
Track 1
1 (4/4)
2 (7/8)
3 (7/8)
4 (5/4)
5 (2/4)
After Insert
Measures 2 and 3 will be 7/8, measures 4

and 5 will be the existing time signature.
If measures are inserted between measures spanned by a note in a MIDI

track, that note will be turned off immediately before the inserted measure;
i.e., it will be shortened from its original duration.
53H: Copy Measure

This command copies playback data from the audio track specified in the dialog
box to the Start Measure of the audio track specified in the tab 3 page.
Be aware that executing the Copy Measure command will change the playback
data as follows.
If you copy measures which contain no playback data, the copy destination
measures will be blank.
The playback data previously located at the copy destination will be erased,
and replaced by the copied playback data.
The playback data of the copied measures will be played back in accordance
with the time signature of the copy destination.
1 In the tab 3 page, specify the copy destination track and the Start Measure.
2 When you choose Copy Measure, the dialog box at right will appear.
3 Specify the copy source song.

4 Specify the copy source audio track. If you
wish to copy the playback data of all tracks
of the specified song including the MIDI
tracks, check the All Tracks box.
This is an easy way to create repeated sections such as refrains within a song.
5 Specify the copy source Start Measure and End Measure.
6 To execute the Copy Measure command, press the OK button. To cancel
37
Parameters
Measures 4 and 5 will be the existing time

signature.
Appendix
Two measures inserted
Operation
Time signature = 7/8
Time signature = **/**
Sequencer P5
Example: If measures 57 of track 1 are copied to measure 3 of track 2, measures 35 of track 2 will be written.
Track 1
(source)
1 (4/4)
2 (4/4)
3 (4/4)
4 (3/4)
5 (3/4)
6 (3/4)
7 (4/4)
Track 2
(destination)
1 (4/4)
2 (4/4)
3 (4/4)
4 (3/4)
5 (3/4)
6 (3/4)
7 (4/4)
If Audio Events would overlap as a result of executing this command, the

lower portion of the overlap will be erased when you press the Execute button.
If you execute the Copy Measure command between songs whose Tempo
settings differ, the playback time will be different even if the number of measures is identical. This will cause problems such as the data failing to fit
within the specified measures, or a gap resulting.
53I: Move Measure

This command moves measures of playback data from the audio track specified
in the dialog box to the Start Measure of the audio track specified in the tab 3
page.
Be aware that executing the Move Measure command will change the playback
data as follows.
Playback data following the move source measures will slide toward the
beginning of the song by the number of measures that were moved.
Playback data following the move destination measure will slide toward the
end of the song by the number of measures that were moved.
1 In the tab 3 page, specify the move destination track and the Start Measure.
2 When you choose Move Measure, the dialog box at right will appear.
3 Specify the move source audio track.

If you wish to move the playback data of all
All Tracks box.
4 Specify the Start Measure and End Measure
of the move source.
5 To execute the Move Measure command, press the OK button. To cancel

If Audio Events would overlap as a result of executing this command, the
lower portion of the overlap will be erased when you press the Execute button.
38
Sequencer P5
This command lets you perform event editing of audio events (events in the
audio tracks), and trim the sound used by an audio event (i.e., adjust the location or the area where the sound will be heard, in steps of one sample).
If you wish to modify the sound name after recording, you can do so in the Trim
dialog box.
1 In the tab 3 page, select the track that contains the audio event you wish to
edit, and specify the Start Measure.
2 When you choose Audio Event Edit, the following dialog box (Audio Event
Introduction
53J: Audio Event Edit
Edit) will appear.

Sound name of audio event
Operation
Ending location of audio event

(measure, beat, clock)
a: Index
b: Measure
a: Scroll bar
A: Trim button
Execute button
B: Insert button
D: Copy button
E: Audition start/stop button
C: Delete button
a: To select the audio event that you wish to edit, select an index, use the
scroll bar, or directly press the desired event.
At this time, you can press the Audition Start/Stop button once to playback the event, allowing you to hear the contents. During playback, press
the button once again to stop.
b: You can move the event by modifying the measure or location values.
When moving an event in this way by modifying its location values, you
are not limited to movement within the current measure (unlike Event
Edit for a MIDI track).
c: Adjust the volume for each audio event. The value will be 127 immediately after recording.
3 Press the appropriate button to perform the desired operations explained
below: Trim audio event, Insert audio event, Delete audio event,
Copy audio event, or Audition start/stop.
When you are finished with event editing, press the Done button to return to
the tab page.
A: Trim button
Trimming an audio event
The Trim operation lets you specify in units of a sample the portion of a
recorded sound that will be played back, allowing you to adjust the timing of
the sound or to remove unwanted space.
Since the trim source sound is kept unchanged from its original recorded state,
you can later restore the sound to its original condition even if you shorten it
excessively by mistake. Executing the Trim operation simply changes the location where the sound begins to playback, and the location of the sound event
39
Parameters
c: Volume
Appendix
Location in measure b:
(beat, clock)
Sequencer P5
within the song is not affected.

Here you can also modify the sound name that was recorded.
Select the audio event that you wish to trim, and press the Trim button. You will
enter Trim mode, and the following dialog box will appear.
a
d
Audition buttons
Play To Point button
Play Through Point button
Play From Point button
Cancel button
Execute button
All Play/Stop button
Audition buttons
Play To Point button
Playback from approximately 2 seconds before the edit point until

the edit point and then stop.
Play Through Point button
Playback approximately 4 seconds surrounding the edit point and

then stop.
Play From Point button
Playback from the edit point for approximately 2 seconds and then
stop.
When you press the All Play/Stop button once, the audio event will playback
from start to end, allowing you to check the result of your trim setting. During
playback you can press the button once again to stop. This button can also be
used to stop playback that was initiated by the three audition buttons at left.
To execute the Trim operation, press the Done button. To return to the previous
tab page, press the Cancel button. If you press the Cancel button, your edits
will be canceled, and you will return from this dialog box to the Audio Event
Edit dialog box. However a sound name that you have edited here will not be
canceled.
a: Audio Track
This displays the selected track (the track selected when you entered Trim
mode).
b: Location/Sound name
This displays the location in the track of the audio event being trimmed, and the
name of the sound used by that event. You can use the text edit button to edit
the sound name.
c: Audition Parameters
Speed [x1, x7/8, x6/8, x5/8, x4/8] lets you specify the playback speed. By
adjusting the playback speed you can find the appropriate trim points more
accurately.
If the Repeat box is checked, pressing an audition button will cause the
audio event to be played back repeatedly. To stop playback, press the All
Play/Stop button.
40
If the selected audio event is monaural, it will not be possible to check the
Stereo Edit box.
Edit Step (1, 100, 10000 samples) determines the detail (the units) with which
the VALUE dial or the []/[] keys will adjust the Sample Start or Sample
End values.
Executing the trim operation
Suppose that you are trimming an audio event located at the beginning of measure 5 and consisting of the phrases; The weather is very nice today. Yes, it
is.
Operation
If you perform the Trim operation on only one of a stereo pair of tracks,
phase discrepancies may occur. We recommend that you check the Stereo
Edit box when trimming stereo data.
Parameters
d: Trim Parameters
Here you can specify the various points for trimming (refer to the diagrams
below).
Sample Start and Sample End (min:sec.sample) specify the range of the
recorded audio event that will actually be played back.
Sample Start is the location where the audio event will begin playing back.
This is indicated as the time from the beginning of the sound.
Sample End is the location where the audio event will stop playing back.
This is indicated as the time from the beginning of the sound.
When Sample Start or Sample End are selected (i.e., when the parameters are
highlighted, you can use an audition button to playback the audio event and
press the [Enter] key at the appropriate moment to input that location as the
Sample Start or Sample End value (the grab function).
Duration (min:sec:msec) indicates the length of the audio event that will be
played back (the distance between Sample Start and Sample End). This is
only displayed, and cannot be edited.
If the Stereo Edit box is checked, selecting an audio event in one audio track
of a stereo-recorded pair will cause the Trim operation to be applied to the
other audio event as well.
Introduction
Sequencer P5
Audio event that is played back

The weather is
very nice today.
Yes, it is.
Appendix
Before trimming
005.01.000
If you want very nice today to playback at the beginning of measure 5, set
Sample Start before very and Sample End after nice today.
Duration
Trim parameter settings
The weather is
very nice today.
Sample Start
Yes, it is.
Sample End
Executing these settings will cause the audio event to playback from the specified Sample Start location, and very nice today will playback at the beginning
of measure 5.
Audio event that is played back
After trimming
The weather is
very nice today.
Yes, it is.
005.01.000
If you once again adjust the trim duration to include The weather is and Yes,
it is, the entire audio event will be played back as originally.
41
Sequencer P5
B: Insert button
Inserting an audio event
Select the audio event that you wish to insert, and press the Copy button. Next,
select an audio event and press the Insert button to insert the previously copied
event at the End Time location of the selected audio event (refer to the diagrams
below).
Audio events can be inserted into locations in which other events do not exist.
(They cannot be inserted where other events exist.)
If the interval between audio events 1 and 3 is longer than audio event 2 , audio
event 2 can be inserted as it is.
Insert
2
3
If the interval between audio events 1 and 3 is shorter than audio event 2 , audio
event 2 can be inserted, but it will be played only up to the Start Time of audio
event 3 .
Although event 2 will be played only for a limited duration in this case, it will
once again play in its entirety if it is moved to an unoccupied location of sufficient length.
Insert
Moving an audio event

To move an inserted audio event, use b: Location to adjust the Start Time. This
can be set anywhere between the End Time of the preceding audio event and the
Start Time of the following audio event. If you wish to move an audio event past
another audio event, select the audio event that you wish to move and press the
Delete button. Then press the Insert button at the desired new location to insert
that audio event.
C: Delete button
Deleting an audio event
Select the audio event that you wish to delete, and press the Delete button.
The audio event will be deleted.
D: Copy button
Copying an audio event
Select the audio event that you wish to copy, and press the Copy button. Then
use the Insert button to insert the audio event that you copied.
42
Sequencer P5
Appendix
Parameters
Operation
Start/stop audition
When an audio event is highlighted, you can press the Audition Start/Stop button once to playback that audio event. Pressing the button once again during
playback will stop the playback.
Introduction
E: Audition Start/Stop button
43
Sequencer P5
54: Audio Track Name

Here you can assign a name to each audio track.
Page Menu
54F
54G
54j
54B
54H
54C
54I
54D
54J
54E
54j: Audio Track Name

Use the text edit button to assign a name to the audio track.
The audio track name is displayed in the various tab pages of Sequencer mode
P1, P2, and P5.
Page Menu Command

54B: Automation Edit
This command lets you edit individual mixer events that were recorded. Event
editing of an audio track can be done using 53J: Audio Event Edit.
For details on the procedure, refer to 53B: Automation Edit.
54C: Erase Audio Track

This command erases all playback data from the audio track selected in the tab 3
page.
For details on the procedure, refer to 53C: Erase Audio Track.
54D: Copy Audio Track

This command copies playback data from the audio track selected in the dialog
box to the audio track specified in the tab 3 page.
Be aware that when you execute the Copy Audio Track command, all playback
data that previously existed in the copy destination track will be erased.
For details on the procedure, refer to 53D: Copy Audio Track.
54E: Erase Measure

This command erases specified measures of playback data from the track
You can specify the type(s) of data that will be erased.
Unlike the Delete Measure command, executing the Erase Measure command
will not cause playback data following the erased area to be moved toward the
beginning of the song.
44
Sequencer P5
54F: Delete Measure

This command deletes specified measures of playback data from the track
Unlike the Erase Measure command, executing the Delete Measure command
will cause playback data following the deleted area to be moved forward
toward the beginning of the song.
For details on the procedure, refer to 53F: Delete Measure.
Introduction
For details on the procedure, refer to 53E: Erase Measure.
This command inserts the number of measures specified in the dialog box into
the track specified in the tab 3 page. When the Insert Measure command is executed, the measures will be inserted at the location specified by the Start Measure. The playback data following the inserted location will be moved backward
toward the end of the song.
For details on the procedure, refer to 53G: Insert Measure.
54H: Copy Measure
Operation
54G: Insert Measure
Be aware that the playback data will change as follows when the Copy Measure
command is executed.
If measures which contain no playback data are copied, the copy destination
measures will be blank.
Any playback data existing at the copy destination will be erased, and
replaced by the copied playback data.
The playback data that is copied will be played back according to the time
signature of the copy destination.
Parameters
This command copies specified measures of playback data from the audio track
selected in the dialog box to the Start Measure of the audio track selected in the
tab 3 page.
For details on the procedure, refer to 53H: Copy Measure.
This command moves playback data of the audio track selected in the dialog
box to the Start Measure location of the audio track specified in the tab 3 page, in
steps of a measure.
Be aware that the playback data will change as follows when the Move Measure
command is executed.
Playback data located after the move source measures will be shifted forward
by the number of measures that were moved.
Playback data located after the move destination measure will be shifted
backward by the number of measures that were moved.
For details on the procedure, refer to 53I: Move Measure.
54J: Audio Event Edit

This command lets you perform event editing of audio events (events in an
audio track), and trim the sound that is used by an audio event (make sampleunit adjustments in the location or portion of a sound that will be played back).
You can use the Trim dialog box to modify the sound name after recording.
For details on the procedure, refer to 53J: Audio Event.
45
Appendix
54I: Move Measure
Disk P1
Disk P1
A note about .SNG files which contain audio tracks
Sequence data that contains audio tracks in the song is saved as a .SNG file.
The filename extension is the same as for song files which contain only MIDI
song data, but the following icon will appear for songs which contain an audio
track.
11: Load
Page Menu
11B
Page Menu Command

11B: Load Selected
If an .SNG file was selected, all audio track data will be loaded. If a 1-song file
was selected, the audio events used by that song will be loaded.
46
Disk P1
Here you can perform various operations on the selected file or disk drive. Use
Drive Select or the directory window to select a disk drive or file, and then
choose a command from the page menu.
Page Menu
Introduction
13: Utility
13B
Operation
13C
13G
13H
13B: Rename
Modifies the name of the selected file or directory. However it is not possible to
modify the name of a .SNG file containing a song that includes an audio track.
(Refer to the top of page 46 for the icon.) Also, the Rename command is available only when a DOS file or DOS directory is selected.
13C: Copy
Parameters
Page Menu Command
Copies the selected file.
1 In the tab 3 page, select the file you

wish to copy.
Appendix
2 When you choose Copy, the dialog

box at right will appear.
3 Use Drive Select to select the copy

destination disk, and use the Open
or Up buttons to select the copy
destination directory.
4 If you wish to change the filename,
use the text edit box to change the
name.
5 To execute the copy command, press the Copy button. To cancel without
copying, press the Cancel button.
If the drive selected by Drive Select is removable media (such as a floppy
disk or a removable hard disk, etc.), it will not be possible to copy between
different media on the same drive.
47
Disk P1
13G: Format
Formats the selected floppy disk or hard disk (or other SCSI device).
If the hard disk is being used by the TRINITY series for the first time, the hard
disk must first be formatted to establish a filer partition and a sound partition.
When formatting is executed, all data that was previously on that hard disk
will be erased. Before formatting a disk, make sure that it does not contain
data you wish to keep.
The size of the filer partition cannot be modified during use. If you wish to
change the size, you must once again execute either Format or Wipe. Be
aware that this will erase all data of the hard disk.
1 In the tab 3 page, select the floppy disk or hard disk.

2 When you choose Format, the dialog box at
right will appear. (The dialog box pictured
here is for formatting a hard disk. For a
floppy disk, the Filer Size setting will not
appear.)
3 Use the text edit button to assign a volume
label to the hard disk.
4 Specify the size of the partition used for saving .SNG files and .PCG files, etc.
This can be set in a range of 0540 Mbytes.
The remaining space of the hard disk will be used for recording sound.
If you are using only a single hard disk to perform hard disk recording,
you must specify a filer partition larger than 0 in order to create an area
where .SNG files and .PCG files etc. can be saved. If you are using two or
more hard disks, a filer partition must be created on at least one of the
disks.
5 Press the OK button, and the display will ask Are you sure?. Press OK
once again to execute the Format command.
Formatting a hard disk will require a certain amount of time depending on
the size of the hard disk. (e.g., formatting a 540 Mbyte hard disk requires
approximately 5 minutes.)
Pressing the [COMPARE] key after executing this command will not undo
the command.
Do not install a hard disk that was formatted on the TRINITY series into
another computer. Korg cannot guarantee the operation of such a disk.
13H: Wipe
Erases all data existing on the selected floppy disk or hard disk.
The size of the filer partition cannot be modified during use. If you wish to
change the size, you must once again execute either Format or Wipe. Be
aware that this will erase all data of the hard disk.
1 In the tab 3 page, select a floppy disk or a hard disk.

2 When you choose Wipe, the dialog box at
right will appear. (The dialog box pictured
here is for wiping a hard disk. For a floppy
disk, the Filer Size setting will not appear.)
If you wish to change the volume label, use
the text edit button.
48
Disk P1
.PCG files, etc. The remaining area of the hard disk will be used for recording
sound.
This can be set in a range of 0540 Mbytes.
4 Press the OK button, and the display will ask Are you sure?. Press OK
once again to execute the Wipe command.
Appendix
Parameters
Operation
Pressing the [COMPARE] key after executing this command will not undo
the command.
Introduction
3 Specify the size of the partition that will be used for saving .SNG files and
49
Disk P1
14: Audio Utility

Here you can perform operations such as backing up data from hard disk to a
DAT tape, or restoring backed up data from a DAT tape to a hard disk.
Page Menu
14B
14C
14D
14E
14F
Page Menu Command

14B: Backup to DAT
This command backs up one selected .SNG file to DAT tape.
When one .SNG file is backed up, all .PCG files of the same name existing in the
current directory will be backed up together.
Connect the S/P DIF OUT connector located on the rear panel of the TRINITY
to the DIGITAL IN (coaxial) connector of your DAT recorder.
TRINITY
S/P DIF OUT
Connections for backup

DIGITAL IN
(Coaxial)
1 In the tab 4 page, select a .SNG file.

2 When you choose Backup to DAT, the dialog box at right will appear.
3 The Backup Time will be displayed. Insert a

DAT tape of sufficient length into your
DAT recorder.
50
Your DAT recorder
Disk P1
4 Press the OK button, and the dialog box at
Introduction
right will appear.
5 Start recording on your DAT recorder.

6 Press the OK button in the dialog box. The
data will begin to be output, and backup
will begin.
Within approximately 10 seconds, the level
meter on your DAT recorder will begin to
move.
7 When the backup is finished, the display will indicate Complete. When this
display appears, stop your DAT recorder.
If you press the Cancel button during backup in an attempt to create a partial backup, the backed-up data will be incomplete, and even if this data is
restored it will be unusable.
14C: Restore from DAT
Operation
If audio devices are connected to your DAT recorder, make settings so that
the sound from the DAT is not output to speakers or headphones. Speakers
or headphones may be damaged if this precaution is not taken.
This command restores backed-up data from DAT tapes to the hard disk(s).
TRINITY
Parameters
Connect the S/P DIF IN connector located on the rear panel of the TRINITY to
the DIGITAL OUT (coaxial) connector of your DAT recorder.
Connections for restoring
S/P DIF IN
DIGITAL OUT
(Coaxial)
Your DAT recorder
1 Load the tape containing the backup data
Appendix
into your DAT recorder.
2 When you choose Restore from DAT, the

3 Playback your DAT recorder.

4 When the header of the DAT tape has been
read, the dialog box at right will appear.
Stop your DAT recorder within 30 seconds.
(Do not rewind the DAT tape.)
If you do not stop the DAT recorder within
30 seconds, restore cannot be performed
correctly.
51
Disk P1
5 Press the OK button. The dialog box

at right will appear.
Specify the directory into which the
file will be restored.
6 The dialog box of step 2 will reappear. Start the DAT recorder, and
restoring will begin.
7 When the restoration operation is
completed, the display will indicate
Completed. When this display
appears, stop your DAT recorder.
14D: Copy with Sound

This command copies the selected .SNG file with the sounds it uses to another
hard disk. If at this time a .PCG file with the same name exists in the current
directory, it will also be copied.
However if a hard disk and removable media (fixed at ID6) are both connected,
and you select a hard disk of ID05 as the copy source, the copy destination will
be the removable media of ID6. If you select the removable media of ID6 as the
copy source, you will able to select a hard disk of ID05 as the copy destination.
1 In the tab 4 page, select the copy
source /SNG file.
2 When you choose Copy with
Sound, the dialog box at right will
appear.
3 Select the hard disk and directory of
the copy destination, and press the
Copy button.
14E: Disp Used Sound List

This command displays the sounds
used by the selected .SNG file.
1 Select a .SNG file.
2 When you choose Disp Used Sound
List, the dialog box at right will
appear.
3 Press the OK button.
52
Disk P1
This command deletes sounds which are not used by any .SNG file from all hard
disks.
Appendix
Parameters
Operation
After this command has been executed, it is not possible to use the [COMPARE] key to bring back the deleted data.
Introduction
14F: Delete Unused Sound
53
Disk P1
54
Block diagram
Introduction
4. Appendix
Appendix
Parameters
Operation
Block diagram
55
Messages
Messages
When the HDR-TRI is installed, the following messages will be added.
Disk not formatted

Meaning: The disk for which Wipe was attempted is not formatted.
Action:
Use the Format command of the TRINITY to format the disk.
Error in wiping medium

Meaning: Disk wipe could not be performed.
Action:
The disk is damaged. Use a different disk.
Memory full. Audio track cant play to the end.

Meaning: The master track's memory has been used up, so the audio track cannot be played back to the end.
Action:
Increase the available memory of the master track by deleting tempo
changes etc. from the master track.
No unused sounds found

Meaning: When you executed the Disk mode command Delete Unused Sound,
no unused sounds were found.
Troubleshooting
Problem: An asterisk appears to the right of the
page menu button (as shown in the graphic at
the right), and problems such as a flickering
LCD and a drop in volume occur.
If you continue using the unit under these circumstances, functions
may stop working properly. Take the following actions immediately.
Cause:
The clock is not being detected correctly. The cable connected to the
S/P DIF IN connector may not be plugged in, a frequency other than
48 kHz may be transmitting to the S/P DIF IN connector or for a similarly related reason. Also, if the DITRI is installed, the clock may
not be correctly detected because the BNC cable may not be plugged
in, etc.
Action:
First, confirm that the connected cable is working. Then, input the
correct clock [48 kHz (5 Hz) to both the S/P DIF IN connector and
the WORD CLOCK IN connector], and set the Global mode P1 (Global Setup) parameter System Clock to Internal. Before continuing
to use the unit, make sure that normal operation has resumed and
that the asterisk is no longer displayed next to the page menu
button. If these steps do not restore normal operation, turn the power
off and back on. You must first back up the Sequencer memory since
all data will be lost when the power is turned off.
Problem: Sound is distorted.
Cause 1: If the Sequencer mode P1 tab 5 page (Audio Track Rec) settings for
Input Level and/or Rec Level are excessively high (and the display
indicates Overload and/or Over), the input will be overloaded and
distorted sound will be recorded.
56
Cause 3:
Action:
Problem: Sound is not output from the monitor even though the level meters
are up.
Cause 1: There is a problem with the settings of the TRINITY itself or with the
connections.
Action:
Raise the TRINITYs volume, or check the monitor connections.
Cause 2: An audio track is not selected in Track.
Action:
Select an audio track.
Cause 3: Even if an audio track is selected, the tab 6 page (Mix A14) Volume
setting is 0, or Pan is OFF.
Action:
Adjust the Volume and Pan settings.
Specifications
INPUT/OUTPUT connectors: SCSI connector, ANALOG IN 1/2 connectors, S/
P DIF IN/OUT connectors
Sampling frequency: 48 kHz
Recording time: when using a 540 Mbyte hard disk, approximately 94 minutes
of monaural recording, approximately 47 minutes of stereo recording (approximately 5 Mbytes per minute of monaural recording)
Tracks recorded simultaneously: 2
Tracks played back simultaneously: 4
Digital mixer specifications
Volume: 0127 (100=unity)
High EQ: 15+15 (0=unity)
Low EQ: 15 +15 (0=unity)
Send 1: 0127 (send to Master Effect 1)
Send 2: 0127 (send to Master Effect 2)
Pan: L000C064R127, OFF
Analog audio input gain structure
Input Level setting
Typical input level
Max input level
Typical gain
30 dBu
30 dBu
20 dBu
+20 dB
10 dBu
10 dBu
0 dBu
0 dB
+4 dBu
+4 dBu
+14 dBu
14 dB
S/N ratio (A-weighted): better than 90 dB

Measured at OUTPUT 1 and 2 for a 1 kHz sine wave input, Rec Level=0.0,
AT1: Pan=L000, Volume=100, AT2: Pan=R127, Volume=100, AT3/4: MUTE
57
Operation
Action:
Parameters
Cause 2:
Lower the Input Level and/or Rec Level settings so that the Overload and/or Over displays do not appear.
Even if the Input Level and Rec Level settings are appropriate, distorted sound will be output from the monitor if the P1 tab 6 page
(Mix Audio Track 14) Volume setting is too high. (However the
sound that is recorded is not distorted.)
Adjust the volume downward. A volume setting of 0 is -infinity, 100
is 0 dB, and 127 is +127 dB.
In situations other than the above, the output from the monitor will
be distorted if Pan is set to C064 during stereo recording.
During stereo recording, set Pan to L000 and R127.
Appendix
Action:
Introduction
Specifications
Hard Disk Recording Demo Songs: Hard Disk Recording Demo Songs consist of TRINITY seqneuce data
and Audio Data.
1. Godzilla Wants my Trinity
written by John Lehmkuhl, Nick Forcillo and Steve Hunt
1996 RealKuhl Music
Steve Hunt Vocals
Nick Forcillo Guitars
Caroline Lehmkuhl Female radio announcer
John Lehmkuhl voice of Male radio announcer & Godzilla. All production on Trinity including sequencing & playing.
2. WhatCha'GonnaDo?
written by John Lehmkuhl
raps composed by Aaron Bray, Jason Floyd, Jahmad Rollins, Edwin Hamilton, Jason Smith, Ryan Young
1996 Real-Kuhl Music
Aaron Bray, Jason Floyd, Jahmad Rollins, Edwin Hamilton, Jason Smith, Ryan Young Raps John Lehmkuhl All production on Trinity including sequencing & playing.
3. Holy Trinity
written by John Lehmkuhl and Kathy Talbott
1996 RealKuhl Music
Kathy Talbott Vocal
John Lehmkuhl All production on Trinity including sequencing & playing.
4. Paddy Wack
written by John Lehmkuhl
1996 RealKuhl Music
Mindi Abair Alto Saxophone
Charles Moore Mute Trumpet
Ty Stevens Electric Guitars
John Lehmkuhl All production on Trinity including sequencing & playing.
*
John Lehmkuhl / Real-Kuhl Music can be contacted at [email protected] for questions/comment.
** Above Demo song data are not attached to this product.
*** LIMITATION: These HD Demos are for demonstration purposes only in the Trinity Workstation DRS. Unauothorized duplication,
rebroadcast or any other use of the music and/or PCM audio data is strictly prohibited and would constitute a violation of all
applicable laws.
58

Korg Trinity Manual - Expansion Option - HDR-TRI

Uploaded by

Copyright:

Available Formats

Korg Trinity Manual - Expansion Option - HDR-TRI

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Korg Trinity Manual - Expansion Option - HDR-TRI

Uploaded by

Copyright:

Available Formats

HDR-TRI

Hard Disk Recorder Option

54: Audio Track Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Features of the HDR-TRI

4-channel hard disk recorder

About hard disk recording

Features of the HDR-TRI

About hard disks

About hard disks

About sound and audio events

Settings for recording

Hard disk connections and settings

2 On the hard disk, set an ID number in the range of 06.

4 Terminate the hard disk.

Settings for recording

Formatting a hard disk

4 Specify the size (0540 Mbyte) of the filer partition.

5 Press the OK button to execute formatting.

Settings for recording

Types of SCSI devices that can be connected and

Settings for recording

Connections for recording

When recording a guitar that has active pickups,

S/P DIF OUT

Connect a digital recording device (DAT etc.)

Powered monitor speakers etc.

Settings for recording

name, check the Take No. box.

5 In the Take field, specify the take name.

Settings for recording

Checking the external input

1 Access the Sequencer mode P1 tab 5 page (ATrkRec).

2 Select the Input Select item.

Settings for recording

Consumer audio equipment such as CD player

Professional audio equipment and keyboards

4 At this point, set the Rec Level fader to 0.0.

The volume that is output from external monitor speakers is determined

level meter does not rise all the way.

3 In the Recording Setup item, select the recording method.

4 Press the [REC/WRITE] key.

5 Press the [START/STOP] key.

6 To end recording, press the [START/STOP] key.

Recording a guitar in stereo on tracks 3 and 4

2 Connect your guitar to a stereo-output effect device.

Checking the external input

4 In the Track setting, select AT3&4.

5 In the Input Select setting, select Analog.

9 To stop recording, press the [START/STOP] key.

The Compare function

Adjusting the pan or volume balance of the tracks

1 Access the Sequencer mode P1 tab 6 page (MixA14).

5 When you are finished, press the [START/STOP] key.

Recording mixer events

1 Use the procedure Recording an audio track to record an audio track.

When recording mixer events, select Overwrite.

4 Access the tab 6 page (MixA14).

5 For the Track selection, select MIXER REC.

Track Mode to WRITE.

9 When you are finished, press the [START/STOP] key.