Ruckus Indoor-AP User-Guide 100.2.0

Ruckus Wireless
Indoor Access Point

TM
Release 100.2.0 User Guide
For the following indoor Ruckus Wireless AP models:

- ZoneFlex 7055 Dual-Band 802.11n Wired/Wireless Wi-Fi Wall Switch
- ZoneFlex 7321 2.4/5GHz 802.11n Smart Wi-Fi Access Point
- ZoneFlex 7341 Single-Band 802.11n Access Point
- ZoneFlex 7343 Single-Band 802.11n Access Point
- ZoneFlex 7352 802.11n Smart Wi-Fi Access Point
- ZoneFlex 7363 Dual-Band 802.11n Smart Wi-Fi Access Point
- ZoneFlex 7372 and 7372-E Dual-Band 802.11n Smart Wi-Fi Access Point
- ZoneFlex 7441 802.11n DAS Access Point
- ZoneFlex 7982 Dual-Band 802.11n Smart Wi-Fi Access Point
- ZoneFlex H500 Dual-Band 802.11ac Multimedia Wi-Fi Access Point Wall Switch
- ZoneFlex R300 Dual-Band 802.11n Smart Wi-Fi Access Point
- ZoneFlex R500 Dual-Band 802.11ac Smart Wi-Fi Access Point
Part Number 800-70892-001 Rev B

Published 25 June, 2015
www.ruckuswireless.com
Copyright Notice and Proprietary Information

Copyright 2015. Ruckus Wireless, Inc. All rights reserved.
No part of this documentation may be used, reproduced, transmitted, or translated, in any form or by any means,
electronic, mechanical, manual, optical, or otherwise, without prior written permission of Ruckus Wireless, Inc.
(Ruckus), or as expressly provided by under license from Ruckus.
Destination Control Statement

Technical data contained in this publication may be subject to the export control laws of the United States of America.
Disclosure to nationals of other countries contrary to United States law is prohibited. It is the readers responsibility to
determine the applicable regulations and to comply with them.
Disclaimer
THIS DOCUMENTATION AND ALL INFORMATION CONTAINED HEREIN (MATERIAL) IS PROVIDED FOR GENERAL
INFORMATION PURPOSES ONLY. RUCKUS AND ITS LICENSORS MAKE NO WARRANTY OF ANY KIND, EXPRESS
OR IMPLIED, WITH REGARD TO THE MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY, NON-INFRINGEMENT AND FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE
MATERIAL IS ERROR-FREE, ACCURATE OR RELIABLE. RUCKUS RESERVES THE RIGHT TO MAKE CHANGES OR
UPDATES TO THE MATERIAL AT ANY TIME.
Limitation of Liability
IN NO EVENT SHALL RUCKUS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, DATA OR USE, INCURRED BY YOU OR ANY
THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT OR TORT, ARISING FROM YOUR ACCESS TO, OR USE
OF, THE MATERIAL.
Trademarks
Ruckus Wireless, Ruckus, Bark Logo, BeamFlex, ChannelFly, Ruckus Pervasive Performance, SmartCell, ZoneFlex,
Dynamic PSK, FlexMaster, MediaFlex, MetroFlex, Simply Better Wireless, SmartCast, SmartMesh, SmartSec, SpeedFlex, ZoneDirector, ZoneSwitch, and ZonePlanner are trademarks of Ruckus Wireless, Inc. in the United States and
other countries. All other product or company names may be trademarks of their respective owners.
Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A
Contents
1
About This Guide

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Introducing the Ruckus Wireless AP

Overview of the Ruckus Wireless AP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Unpacking the Ruckus Wireless AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Getting to Know the AP Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ZoneFlex 7055 Dual-Band Wired/Wireless Wall Switch . . . . . . . . . . . . . . . . . . . . . . . . 15
ZoneFlex 7321 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ZoneFlex 7341 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ZoneFlex 7343 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ZoneFlex 7352 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ZoneFlex 7363 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ZoneFlex 7372 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ZoneFlex 7372-E AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
ZoneFlex 7441 DAS AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
ZoneFlex 7982 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
ZoneFlex H500 AP Wall Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ZoneFlex R300 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ZoneFlex R500 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
ZoneFlex R600 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
ZoneFlex R700 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
ZoneFlex R710 AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Installing the AP
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Performing a Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Preparing the Required Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Determining the Optimal Mounting Location and Orientation . . . . . . . . . . . . . . . . . . . . 78
Step 1: Preconfiguring the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Configuring the AP for Management by an SCG, SZ or vSZ Controller . . . . . . . . . . . . . 81

Configuring the AP for Management by ZD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Configuring the AP for Standalone Operation or for Management by FM . . . . . . . . . . . 82
Step 2: Verifying AP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Connecting the AP to the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Associating a Wireless Client with the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Checking the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Checking the TR069 Status (FlexMaster Management Only) . . . . . . . . . . . . . . . . . . . . 93
Disconnecting the AP from the Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Step 3: Deploying the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
1. Choosing a Location for the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
2. Connecting the AP to a Power Source and the Network . . . . . . . . . . . . . . . . . . . . . 95
Troubleshooting the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
7055 Physical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Using the 110 Punch Down Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
7441 Physical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Distributed Antenna System Deployment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Antenna Gain and Cable Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Mounting Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
H500 Physical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Navigating the Web Interface

Before You Begin: Preconfiguring the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Configuring the AP for Management by an SCG, SZ or vSZ Controller . . . . . . . . . . . . 109
Configuring the AP for Management by ZD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Configuring the AP for Standalone Operation or for Management by FM . . . . . . . . . . 110
Navigating the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
When You Are Using a Dual-Band AP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Configuring the AP
Configuring Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Configuring Internet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
VLAN Settings Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Configuring NTP Server and Management VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Default IP Addressing Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Obtaining and Assigning an IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Configuring L2TP Connection Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Configuring Local Subnets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Configuring Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Configuring Common Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Configuring Common Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Configuring Wireless # (WLAN Number) Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Configuring Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Setting Ethernet Port Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Working with Port-Based VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Working with 802.1X on Wired Ethernet Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Configuring Hotspot Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Customizing Hotspot Optional Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Creating a Hotspot Walled Garden. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Allowing Unrestricted Access by MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Managing the AP
Viewing Current Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Viewing Current Internet Connection Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Viewing Current Local Subnet Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Viewing Common Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Viewing Associated Wireless Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Changing the Administrative Login Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Enabling Other Management Access Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Viewing FlexMaster Management Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Pointing the AP to FlexMaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Working with Event Logs and Syslog Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Enabling Logging and Sending Event Logs to a Syslog Server . . . . . . . . . . . . . . . . . . 173
Sending a Copy of the Log File to Ruckus Wireless Support . . . . . . . . . . . . . . . . . . . 174
Saving a Copy of the Current Log to Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . 174
Upgrading the Firmware Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Upgrading Manually via FTP or TFTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Upgrading Manually via the Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Upgrading Manually via Local File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Scheduling Automatic Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Rebooting the AP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Resetting the AP to Factory Defaults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Running Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Where to Find More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Appendix A: AP Support for Bluetooth Low Energy Devices

Appendix B: Configuring Link Aggregation (LACP) for AP Backhaul
Index
About This Guide
By downloading this software and subsequently upgrading Ruckus Wireless APs to

base image 100.0.0 and later, please be advised that:
The ZoneDirector periodically connects to Ruckus and Ruckus collects the
ZoneDirector serial number, software version and build number. Ruckus transmits
a file back to the ZoneDirector and this is used to display the current status of the
ZoneDirector Support Contract.
The AP may send a query to Ruckus containing the APs serial number. This allows
your AP to autonomously connect with a wireless LAN controller operated by your
choice of cloud service provider. Ruckus may transmit the Fully Qualified Domain
Name (FQDN) or IP address of the controller that the AP will subsequently attempt
to join back to the AP.
Please be advised that this information may be transferred and stored outside of
your country of residence where data protection standards may be different.
This guide describes how to install, configure and manage Release 100.2.0 Ruckus
Wireless Indoor Access Points (APs). This guide is written for those responsible for
installing and managing network equipment. Consequently, it assumes that the
reader has basic working knowledge of local area networking, wireless networking,
and wireless devices.
NOTE If release notes are available for your product and the information there
differs from the information in this guide, follow the instructions in the release notes.
Most user guides and release notes are available in Adobe Acrobat Reader Portable
Document Format (PDF) or HTML on the Ruckus Wireless Support Web site at
https://support.ruckuswireless.com/documents
Continue with the following:
Safety Warnings
Related Documentation
Documentation Feedback
Document Conventions
About This Guide

Safety Warnings
Safety Warnings
WARNING! Only trained and qualified personnel should be allowed to install,
replace, or service this equipment. The professional installer is responsible for the
proper installation and configuration of this AP. The AP installation must comply with
local regulatory requirements, especially with those regulating operation near military
and/or weather radar systems.
WARNING! Read the installation instructions before you connect the system to its
power source.
WARNING! This product relies on the buildings installation for short-circuit
(overcurrent) protection. Ensure that the protective device is rated not greater than
20A.
WARNING! Installation of this equipment must comply with local and national
electrical codes.
WARNING! Do not operate your wireless device near unshielded blasting caps or
in an explosive environment unless the device has been modified to be especially
qualified for such use.
WARNING! In order to comply with FCC radio frequency (RF) exposure limits,
antennas should be located at a minimum of 7.9 inches (20 cm) or more from the
body of all persons.
WARNING! Ruckus Wireless strongly recommends that you wear eye protection
before mounting the AP.
CAUTION! The fasteners used to mount an AP on a ceiling must be capable of
maintaining a minimum pullout force of 20 lbs (9 kg) and must use all four indented
holes on the mounting bracket.
CAUTION! This product and all interconnected equipment must be installed
indoors within the same building, including the associated LAN connections as
defined by Environment A of the IEEE 802.af Standard.
About This Guide

In addition to this User Guide, each Ruckus Wireless AP documentation set includes
the following:
Installation Guide/Getting Started Guide/Mounting Guide: Provides essential
installation and configuration information to help you get the AP up and running
within minutes.
Online Help: Provides instructions for performing tasks using the APs Web
interface. Online help is accessible from within the Web interface.
Release Notes: Provide information about the current software release, including
new features, enhancements, and known issues.
NOTE For information on Ruckus Wireless controllers, the Ruckus Wireless
controller operating system (SmartZone software), and FlexMaster (FM) managers,
refer to their respective Release Notes and associated user documents.
Documentation Feedback
Ruckus Wireless is interested in improving its documentation and welcomes your
comments and suggestions. You can email your comments to Ruckus Wireless at
[email protected]
When contacting us, please include the following information:
Document title
Document part number (on the cover page)
Page number (if appropriate)
For example:
Ruckus Wireless Indoor AP 100.2.0 User Guide
Part number: 800-70892-001 Revision A
Page 11
Please note that we can only respond to comments and questions about Ruckus
Wireless product documentation at this email address. Questions related to technical support or sales should be directed in the first instance to your network supplier.
About This Guide

Table 1 and Table 2 list the text and notice conventions that are used throughout
this guide.
Table 1.
Text conventions
Convention
Description
monospace
Represents information as it [Device name]>

appears on screen.
monospace bold
Represents information that [Device name]> set

ipaddr 10.0.0.12
you enter.
default font bold
Keyboard keys, software

buttons, and field names.
On the Start menu, click All

Programs.
italics
Screen or page names.
Click Advanced Settings.

The Advanced Settings
page appears.
Table 2.
Example
Notice conventions
Notice Type
Description
NOTE
Information that describes important features or instructions.
CAUTION!
Information that alerts you to potential loss of data or potential

damage to an application, system, or device.
WARNING!
Information that alerts you to potential personal injury.
10
In this chapter:
Overview of the Ruckus Wireless AP
Unpacking the Ruckus Wireless AP
Getting to Know the AP Features
11


Congratulations on your purchase of the Ruckus Wireless AP! Ruckus Wireless APs
are the industrys most easy to use, yet robust and feature-rich Wi-Fi APs designed
to bring power and simplicity together for large-scale indoor deployments.
Your Ruckus Wireless AP uses BeamFlex, a patented antenna technology from
Ruckus Wireless that allows wireless signals to navigate around interference, extend
wireless signal range, and increase speeds and capacity for wireless networks. The
BeamFlex antenna system consists of an array of high-gain directional antenna
elements that allow Ruckus Wireless APs to find quality signal paths in a changing
environment, and sustain the baseline performance required for supporting data,
audio and video applications.
Your Ruckus Wireless AP can be deployed in standalone mode with or without a
FlexMaster (FM) manager, or as part of the Ruckus Wireless Smart WLAN system,
in which it can be managed by a Ruckus Wireless controller. The rest of this
document collectively refers to the SCG, vSCG SZ, vSZ, ZD, SAMs and other
controllers as Ruckus Wireless controllers.
NOTE For more information on the Ruckus Wireless system (including Ruckus
Wireless controllers and FM), BeamFlex, the Ruckus Wireless controller operating
system (SmartZone software), and other Ruckus Wireless technologies, visit
12


1 Open the AP package, and then carefully remove the contents.
2 Return all packing materials to the shipping box, and put the box away in a dry
location.
3 Verify that all items listed in Package Contents below are included in the package.
Check each item for damage. If any item is damaged or missing, notify your
authorized Ruckus Wireless sales representative.
Package Contents
A complete AP package contains all of the items listed below:
Ruckus Wireless AP
Software License Agreement/Product Warranty Statement
Declaration of Conformity, if required
Quick Setup Guide
(Ethernet cables, power adapters and mounting kits are optional accessories
that may or may not be included depending on the SKU purchased)
13


This section identifies the physical features of each Ruckus Wireless AP model that
is discussed in this guide. Before you begin the installation process, Ruckus Wireless
recommends that you become familiar with these features.
ZoneFlex 7055 Dual-Band Wired/Wireless Wall Switch
ZoneFlex 7321 AP
ZoneFlex 7341 AP
ZoneFlex 7343 AP
ZoneFlex 7352 AP
ZoneFlex 7363 AP
ZoneFlex 7372 AP
ZoneFlex 7372-E AP
ZoneFlex 7441 DAS AP
ZoneFlex 7982 AP
ZoneFlex H500 AP Wall Switch
ZoneFlex R300 AP
ZoneFlex R500 AP
ZoneFlex R600 AP
ZoneFlex R700 AP
ZoneFlex R710 AP
NOTE This User Guide does not include information on Ruckus Wireless Outdoor
APs, the 7731 Wireless Bridge, or the P300 Wireless Mesh Bridge. For information
on those Ruckus Wireless models (along with Ruckus Wireless controllers, FM and
MediaFlex product lines), refer to their respective documentation available from
support.ruckuswireless.com
14

ZoneFlex 7055 Dual-Band Wired/Wireless Wall Switch

The ZoneFlex 7055 is a multiservice 802.11n dual-band concurrent two-stream
wired/wireless wall switch.
NOTE The 100.x AP base images support standalone mode and FlexMaster (FM)
WLAN manager operation. The SmartZone software-compatible images only
support Ruckus Wireless SCG, SZ and vSZ controllers. The ZD-compatible images
only support ZD controllers.
The 7055 requires a minimum of AP base image 100.0.0 and later to operate, or
SCG 1.0 and later, vSZ 2.5 and later, SmartZone software 3.2 and later, or ZD 9.6
and later to operate.
The 7055 is designed for installation in an electrical junction box. This section
identifies the physical features the 7055. Before you begin the installation process,
Ruckus Wireless recommends that you become familiar with these features.
Front View Features

The front view of the 7055 includes four Ethernet Ports, a pass through port and a
DC in socket on the bottom front panel. Refer to Table 3 for more information.
Figure 1. ZF7055 front view
1
2
3
Table 3.
ZF7055 front view features
Number Name
1
Description
Pass Through port Pass through port.
15

Table 3.
ZF7055 front view features (Continued)
Number Name
Description
Power Input
Optional 48V DC power input.
LAN1-LAN3
Three 10/100 RJ-45 Ethernet Ports.
LAN4
One 10/100 RJ-45 LAN port with PoE out. Supports

802.3af PSE Class 0/2 (depending on power input).
Reset buttons
Refer to Reset Buttons on page 18 for details.
Rear Panel Features

Figure 2 shows the rear panel of the 7055. For a description of each rear panel
element, refer to Table 4.
Figure 2. ZF7055 rear panel
3
2
Table 4.
ZF 7055 rear panel features
Number Name
Description
PoE In LAN/Uplink Uplink LAN port that supports 802.3af and 802.3at
Power over Ethernet (PoE) input.
Punch down Block 110 punchdown block.
Pass Through Port RJ-45 pass through port for the pass through
connection.
16

Table 4.
ZF 7055 rear panel features (Continued)
Number Name
Description
See Table 5 for LED descriptions and behaviors.
LEDs
LEDs
Refer to Table 5 for descriptions of LEDs and their behaviors. The LEDs are not
visible once the AP is installed.
Table 5.
ZF 7055 LEDs
LED
Meaning
PWR
Green: On
Red: Bootup in process
Off: Off
WAN
Green: Link up.

Flashing green: Activity.
Off: Link down.
5G
Off: The WLAN service is down.

Amber: The WLAN is up, but no clients are associated and no downlink MAPs
are connected.
Green: The WLAN is up and at least one client is associated. No downlink
MAPs are connected.
Slow flashing green (one flash every two seconds): The WLAN is up and at
least one downlink MAP is connected. No clients are associated.
Fast flashing green (two flashes every second): The WLAN is up, at least
one downlink MAP is connected, and at least one client is associated.
2.4G

Amber: The WLAN is up, but no clients are associated and no downlink MAPs
are connected.
Green: The WLAN is up and at least one client is associated. No downlink
MAPs are connected.
17

Table 5.
ZF 7055 LEDs (Continued)
LED
Meaning
AIR
Off: The AP is operating in standalone mode or operating as a root AP (RAP)

or a non-mesh AP.
Green: The AP is functioning as a Mesh AP (MAP), and the wireless signal to
its uplink AP is good.
Fast flashing green (two flashes every second): The AP is functioning as a
Mesh AP (MAP), and the wireless signal to its uplink AP is fair.
Slow flashing green (one flash every two seconds): Mesh networking is
enabled, but the AP is still searching for a mesh uplink.
DIR
Off: The AP is not being managed by ZoneDirector (standalone mode).

Green: The AP is being managed by ZoneDirector.
Slow flashing green (one flash every two seconds): The AP is being
managed by ZoneDirector, but is currently unable to communicate with
ZoneDirector.
Fast flashing green (two flashes every second): The AP is being managed
by ZoneDirector and is currently receiving configuration settings (provisioning)
or an image update.
LAN1 - Green: Link up.

LAN4 Flashing green: Activity.
Off: Link down.
Reset Buttons
Two reset buttons on the left side of the AP are used to reboot or factory reset the AP.
Figure 3. Reset buttons
Press and hold the Soft Reset button for three seconds or more to reset the AP to
factory defaults. Press and release the Hard Reset button to restart the AP.
NOTE On the 7055, the Hard reset button restarts the AP, while the Soft reset
button reverts the AP to factory default settings.
18

ZoneFlex 7321 AP
The ZoneFlex 7321 is a best price/performance dual-band 802.11n SME AP.
support SCG, SZ and vSZ controllers. The ZD-compatible images only support ZD
controllers.
The 7321 includes five LEDs on its front panel and buttons and connectors on its
rear panel.
Front Panel
Figure 4 shows the top view of the 7321. For a description of front panel elements,
refer to Table 6.
Figure 4. 7321 front panel
Table 6.
LED
PWR LED
7321 front panel elements

Description
Off: Off.
Red: Boot up in process.
Green: On.
19

Table 6.
7321 front panel elements (Continued)
LED
Description
AIR LED
Off: The AP is operating in standalone mode or operating as a

root AP (RAP) or a non-mesh AP.
Green: The AP is functioning as a Mesh AP (MAP), and the
wireless signal to its uplink AP is good.
Fast flashing green (two flashes every second): The AP is
functioning as a Mesh AP (MAP), and the wireless signal to its
uplink AP is fair.
Slow flashing green (one flash every two seconds): Mesh
networking is enabled, but the AP is still searching for a mesh
uplink.
DIR LED
Off: The AP is not being managed by ZoneDirector (standalone

mode).
managed by ZoneDirector, but is currently unable to communicate
with ZoneDirector.
Fast flashing green (two flashes every second): The AP is being
managed by ZoneDirector and is currently receiving configuration
settings (provisioning) or an image update.
2.4G LED (WLAN) Off: The WLAN service is down.

Amber: The WLAN is up, but no clients are associated and no
downlink MAPs are connected.
Green: The WLAN is up and at least one client is associated. No
Slow flashing green (one flash every two seconds): The WLAN is
up and at least one downlink MAP is connected. No clients are
associated.
Fast flashing green (two flashes every second): The WLAN is up,
at least one downlink MAP is connected, and at least one client
is associated.
20

Table 6.
7321 front panel elements (Continued)
LED
Description
5G LED (WLAN)

Amber: The WLAN is up, but no clients are associated and no
associated.
at least one downlink MAP is connected, and at least one client
is associated.
Rear Panel
Figure 5 shows the bottom view of the 7321. For a description of each rear panel
part, refer to Table 11.
Figure 5. 7321 rear panel
21

ZoneFlex 7341 AP
Ruckus Wireless controllers 1.0 and later, vSZ 2.5 and later, or ZD 9.0 and later to
operate.
ZoneFlex 7341 includes five LEDs on its front panel and buttons and connectors
on its rear panel.
Front Panel
Figure 6 shows the front panel of the ZoneFlex 7341. For a description of each front
panel part, refer to Table 7.
Figure 6. ZoneFlex 7341 front panel
Table 7.
ZoneFlex 7341 front panel elements
LED
Description
PWR LED
Off: Off.
Green: On.
OPT LED
Not used in this model.
22

Table 7.
ZoneFlex 7341 front panel elements (Continued)
LED
Description
DIR LED
Off: The Access Point is not being managed by ZoneDirector

(standalone mode).
Green: The Access Point is being managed by ZoneDirector.
Slow flashing green (one flash every two seconds): The Access Point
is being managed by ZoneDirector, but is currently unable to
communicate with ZoneDirector.
Fast flashing green (two flashes every second): The Access Point is
being managed by ZoneDirector and is currently receiving
configuration settings (provisioning) or a firmware update.
WLAN LED

Amber: The WLAN service is up and no clients are associated
(standalone), or no wireless clients and no downlink MAPs are
connected (RAP).
Green: The WLAN service is up and at least one wireless client is
associated. If Mesh is enabled, no downlink MAPs are connected.
Fast flashing green: The WLAN service is up, at least one client is
associated, and at least one Mesh downlink is connected.
Slow flashing green: At least one Mesh downlink is connected, and
no clients are associated.
AIR LED
Off: The Access Point is operating in standalone mode or operating

as a root AP (RAP) or a non-mesh AP.
Green: The AP is functioning as a RAP or MAP and the uplink signal
is good.
networking is enabled, but the AP is still searching for a mesh uplink.
functioning as a MAP and the wireless signal to its uplink AP is fair.
23

Rear Panel
Figure 7 shows the rear panel of the ZoneFlex 7341. For a description of each rear
Figure 7. ZoneFlex 7341 rear panel
3
Table 8.
ZoneFlex 7341 rear panel elements
Number Item Name
Description
OPT Button
Not active in this model at this time.
HARD RESET
Button
Pressing, and then quickly releasing this internal button

reboots the AP. Pressing and holding it for six seconds
resets the AP to factory default settings.
CAUTION! Resetting the AP to factory default
settings erases all previously configured settings.

3
10/100/1000 PoE
Port
One RJ-45 port for a 10/100/1000 PoE (Power over

Ethernet, 802.3af) connection.
Power
Connect the power adapter (12 VDC/1.25A) to this

socket. Power can also be supplied via the 10/100/
1000 PoE (802.3af) port.
24

ZoneFlex 7343 AP
SCG 1.0 and later, vSZ 2.5 and later, or ZD 9.0 and later to operate.
ZoneFlex 7343 includes five LEDs on its front panel, and buttons and connectors
on its rear panel.
Front Panel
Figure 8 shows the front panel of the ZoneFlex 7343. For a description of each front
Figure 8. ZoneFlex 7343 front panel
Table 9.
ZoneFlex 7343 front panel elements
LED
Description
PWR LED
Off: Off.
Green: On.
OPT LED
25

Table 9.
ZoneFlex 7343 front panel elements (Continued)
LED
Description
DIR LED
Off: The Access Point is not being managed by ZoneDirector

(standalone mode).
Green: The Access Point is being managed by ZoneDirector.
Slow flashing green (one flash every two seconds): The Access Point
is being managed by ZoneDirector, but is currently unable to
Fast flashing green (two flashes every second): The Access Point is
being managed by ZoneDirector and is currently receiving
configuration settings (provisioning) or a firmware update.
WLAN LED

connected (RAP).
Fast flashing green: The WLAN service is up, at least one client is
associated, and at least one Mesh downlink is connected.
AIR LED
Off: The Access Point is operating in standalone mode or operating

as a root AP (RAP) or a non-mesh AP.
Green: The AP is functioning as a RAP or MAP and the uplink signal
is good.
networking is enabled, but the AP is still searching for a mesh uplink.
26

Rear Panel
Figure 9 shows the rear panel of the ZoneFlex 7343. For a description of each rear
Figure 9. ZoneFlex 7343 rear panel
3
Table 10. ZoneFlex 7343 rear panel elements

Number Item Name
Description
OPT Button
HARD RESET
Button


3
10/100 Ports (2)
Two RJ-45 ports for 10/100Mbps connections.
10/100/1000 PoE
Port

Power

1000 PoE (802.3af) port.
27

ZoneFlex 7352 AP
The ZoneFlex 7352 single-band (2.4 GHz) is a best-performing, mobile-ready, twostream AP.
support Ruckus Wireless SCG, SZ and vSZ controllers The ZD-compatible images
SCG 1.1.1 and later, vSZ 2.5 and later, SmartZone software 3.2 and later, or ZD
9.5.1 and later to operate.
rear panel.
Front Panel
Figure 10 shows the top view of the 7352. For a description of each front panel part,
refer to Table 11.
Figure 10. 7352 top view
28

Table 11. 7352 front panel elements

LED
Description
PWR LED
Off: Off.
Green: On.
OPT LED
DIR LED

mode).
with ZoneDirector.
WLAN LED

connected (RAP).
Fast flashing green: The WLAN service is up, at least one client
is associated, and at least one Mesh downlink is connected.
AIR LED
Off: The AP is operating in standalone mode or operating as a root

AP (RAP) or a non-mesh AP.
Green: The AP is functioning as a RAP or MAP and the uplink
signal is good.
uplink.
29

Rear Panel
Figure 11 shows the rear panel of the 7352 (and 7372). For a description of each
rear panel part, refer to Table 12.
Figure 11. 7352/7372 rear panel
Table 12. 7352/7372 rear panel elements

Number Item Name
Description
10/100/1000+PoE One RJ-45 port for a 10/100/1000 PoE (Power over

Port
10/100 Port
One RJ-45 port for a 10/100 connection.
Power

1000 PoE port.
RST Button

30

ZoneFlex 7363 AP
The ZoneFlex 7363 is a high-performance, 802.11n mid-range Smart Wi-Fi AP with
adaptive antenna technology.
Ruckus Wireless controllers 1.0 and later, vSZ 2.5 and later, or ZD 9.0 and later to
operate.
The 7363 includes five LEDs on its front panel, and buttons and connectors on its
rear panel.
Front Panel
Figure 12 shows the front panel of the 7363. For a description of each front panel

LED
Description
PWR LED
Off: Off.
Amber: Boot up in process.
Green: On.
OPT LED
31

Table 13. 7363 front panel elements (Continued)

LED
Description
DIR LED

mode).
Slow flashing green (one flash every two seconds): The AP is
being managed by ZoneDirector, but is currently unable to
managed by ZoneDirector and is currently receiving
configuration settings (provisioning) or an image update.
2.4G LED (WLAN) Off: The WLAN service is down.

Green: The WLAN service is up, at least one client is associated,
and signal quality is good (RSSI >= 15).
Flashing green (two flashes every second): The WLAN service
is up but no clients are associated.
Amber: The WLAN service is up, at least one client is
associated, but signal quality is poor (RSSI < 15).
5G LED (WLAN)

Green: The WLAN service is up, at least one client is associated
(standalone), or at least one downlink MAP is connected (RAP),
or uplink RAP is connected (MAP), and signal quality is good
(RSSI >= 15).
Fast flashing green (two flashes every second): The WLAN
service is up but no clients are associated (standalone), no
downlink MAPs are connected (RAP), or no uplink RAP is
connected (MAP).
Amber: The WLAN service is up, at least one wireless client is
associated (standalone), or at least one downlink MAP is
connected (RAP), or uplink RAP is connected (MAP), but signal
quality is poor (RSSI < 15).
32

Rear Panel
3
Table 14. 7363 rear panel elements

Number Item Name
Description
OPT Button
HARD RESET
Button


3
10/100 Ports (2)
Two RJ-45 ports for 10/100Mbps connections.
10/100/1000 PoE
Port

Power

1000 PoE (802.3af) port.
33

ZoneFlex 7372 AP
The ZoneFlex 7372 is a best-performing, concurrent dual-band, mobile-ready, twostream AP.
controllers.
SCG 1.1.1 and later, vSZ 2.5 and later, SmartZone software 3.2 and later, or ZD
rear panel.
Front Panel
refer to Table 15.
34


LED
Description
Power LED
Off: Off.
Green: On.
DIR LED

mode).
with ZoneDirector.
AIR LED

Green: The AP is functioning as a Mesh AP (MAP), and the wireless
signal to its uplink AP is good.
uplink AP is fair.
uplink.
2.4GHz LED

Green: The WLAN is up and at least one client is associated.
Amber: The WLAN is up. No clients are associated.
35


LED
Description
5GHz LED

Amber: The WLAN is up, but no clients or downlink MAPs are
associated/connected.
associated.
at least one downlink MAP is connected, and at least one client is
associated.
Rear Panel
The rear panel of the 7372 is the same as the 7352. See Figure 11.
36

ZoneFlex 7372-E AP
The ZoneFlex 7372-E is a best-performing, concurrent dual-band, mobile-ready,
two-stream AP, with two RP-SMA connectors used to support dual-band 2.4GHz
and 5GHz external antennas.
controllers.
The 7372-E requires a minimum of AP base image 100.0.0 and later to operate, or
The 7372-E includes five LEDs on its front panel and buttons and connectors on its
rear panel.
Front Panel
Figure 14 shows the top view of the 7372-E. For a description of each front panel
Figure 15. 7372-E top view
37

Table 16. 7372-E front panel elements

LED
Description
Power LED
Off: Off.
Green: On.
DIR LED

mode).
with ZoneDirector.
AIR LED

uplink AP is fair.
uplink.
2.4GHz LED

38

Table 16. 7372-E front panel elements (Continued)

LED
Description
5GHz LED

associated.
associated.
Rear Panel
Figure 16 shows the rear panel of the 7372-E. For a description of each rear panel
Figure 16. 7372-E rear panel
39

Table 17. 7372-E rear panel elements

Number Item Name
Description

RST Button

2
10/100/1000+PoE One RJ-45 port for a 10/100/1000 PoE (Power over

Port
10/100 Port
One RJ-45 port for a 10/100 connection.
Power

1000 PoE port.
5 (two
places)
RP-SMA
connectors
Connect to dual-band 2.4GHz and 5GHz external

antennas.
40

ZoneFlex 7441 DAS AP

The ZoneFlex 7441 is a Wi-Fi AP used on coax distributed antenna system (DAS)
networks.
controllers.
The 7441 includes five LEDs, power, network and DAS coaxial connectors on its
front panel.
Front Panel
Figure 17 shows the front view of the 7441. For a description of each front panel

LED
Description
Ground post
Attach the ground wire using the included terminal ring and hex
nuts.
Power socket
DC power socket.
Reset button
Resets the AP to factory default settings if held for more than 5

seconds.
41


LED
Description
10/100/1000 PoE
Ethernet port
One RJ-45 port for a 10/100/1000 802.3af PoE (Power over

Ethernet) connection.
PWR LED
Off: Off.
Green: On.
DIR LED

mode).
2.4G LED

Green: The WLAN service is up and at least one client is
associated with it.
Flashing green: The WLAN service is up and no clients are
associated.
5G LED

associated.
Flashing green: The WLAN service is up and no clients are
associated.
AIR LED
Not used at this time.
Cable antenna
connector
Type N female coaxial cable connector for in-building DAS

wireless systems.
42

ZoneFlex 7982 AP
The ZoneFlex 7982 is a high-capacity, high-performing, three-stream AP for carriers
and enterprises.
controllers.
rear panel.
Front Panel
refer to Table 19.
43


LED
Description
Power LED
Off: Off.
Green: On.
DIR LED

mode).
with ZoneDirector.
AIR LED

uplink AP is fair.
uplink.
2.4GHz LED

44


LED
Description
5GHz LED

associated.
associated.
Rear Panel
45

Table 20. 7982 rear panel elements

Number Item Name
Description
ETHERNET +
PoE Port

Ethernet, 802.3af/at) connection (Note).
ETHERNET Port One RJ-45 port for a 10/100/1000 connection.
12V 1.5A Power Connect the power adapter (12 VDC/1.25A) to this socket.
Socket
Power can also be supplied via the ETHERNET + PoE port.
RESET Button

CAUTION! Resetting the AP to factory default settings
erases all settings that you configured previously.

Note: Class 4 device. Some PoE+ switches reserve 30W for Class 4 device by default.
Table 21. Behavior of Ethernet port LEDs on 7982
LEDs
Description
Off
Not connected
Amber + Green
Connected to 10Mbps device
Amber
Green
WARNING! For units with Power over Ethernet (PoE). These products and all
interconnected equipment must be installed indoors within the same building,
including the associated LAN connections, as defined by Environment A of the IEEE
802.3af Standard.
46

ZoneFlex H500 AP Wall Switch

The H500 is a high-capacity, high-performing, two-stream, dual-band, 802.11ac,
multimedia Wi-Fi AP wall switch with adaptive antenna technology for carriers and
enterprises.
controllers.
The H500 AP requires a minimum of AP base image 100.1.0 and later to operate,
or SCG 3.1 and later, vSZ 3.0 and later, SmartZone software 3.2 and later, or ZD
9.10 and later to operate.
NOTE The H500 is not supported by the ZoneDirector 1100.
The H500 has many options:
It can be mounted on a standard USA- or EU-style single-gang wall outlet box.
It can be powered by a customer-supplied IEEE 802.3af- or 802.3at-compliant
PoE switch or injector, or can be powered by an optional customer-ordered DC
power adapter.
It has side cutouts for one or two bypass cables. The mounting bracket has
locating hooks to keep the bypass cables aligned with the cutouts when
attaching the H500 to the mounting base.
It can have a low-power (0.5W or less) customer-supplied USB device plugged
in. The USB port is intended for low-power devices such as BLE (Bluetooth low
energy) beacons.
The H500 has four LEDs, one RJ-45 connector, and a reset button on its rear panel,
and has one USB port (refer to Appendix A: AP Support for Bluetooth Low Energy
Devices), four RJ-45 connectors, and one DC power connector on its bottom panel.
About Peripheral Devices

The H500 can supply power to USB devices and PoE-powered devices, and the
power supplied depends on the PoE power supplied to the H500.
The USB port is intended for low-power devices such as BLE beacons. The
maximum power that the USB port can supply is 0.5W.
The LAN1+PoE port is intended for PoE-powered peripheral devices such as IP
telephones.
47

For a description of the input and output power options, refer to Table 22.
Table 22. H500 power options and available power out for PoE out and USB
H500 Power Source
Power Available for PoE Out and USB
802.3af PoE
5W total
802.3at PoE
12.95W PoE Out (802.3af Class 3) and

0.5W USB
DC power adapter (sold separately)
12.95W PoE Out (802.3af Class 3) and

0.5W USB
Front Panel
Figure 20 shows the front view of the H500.
Figure 20. H500 front view
48

Rear Panel
Figure 21 shows the rear view of the H500. For a description of each rear panel part,
refer to Table 23.
Figure 21. H500 rear view
1
2
5
Table 23. H500 rear panel elements

No.
LED
Description
PWR
Off: Off.
Green: On.
49

Table 23. H500 rear panel elements (Continued)

No.
LED
Description
CTL
Off: The AP is not being managed by a Ruckus Wireless

controller (standalone mode).
Green: The AP is being managed by a Ruckus Wireless
controller.
Slow flashing green (one flash every two seconds): The AP
is being managed by a Ruckus Wireless controller, but is
currently unable to communicate with the controller.
being managed by a Ruckus Wireless controller and is
currently receiving configuration settings (provisioning) or an
image update.
2 (2.4GHz
WLAN)
Off: The 2.4GHz WLAN service is down.

Green: The WLAN service is up, at least one client is
associated, and signal quality is good (RSSI >= 15).
Amber: The WLAN service is up but no clients are
associated.
5 (5GHz WLAN) Off: The 5GHz WLAN service is down.

Green: The WLAN service is up, at least one client is
associated, and no downlink MAPs are connected.
Slow flashing green (one flash every two seconds): The
WLAN service is up, at least one downlink MAP is
connected, and no clients are associated.
Fast flashing green (two flashes every second): The WLAN
service is up, at least one downlink MAP is connected, and
at least one client is associated.
Amber: The WLAN service is up, but no clients or downlink
MAPs are associated or connected.
PoE In Port
One RJ-45 port for a 10/100/1000 PoE (Power over Ethernet,

802.3af/at Class 3 or 4) connection.
50

Bottom Panel
Figure 22 shows the bottom view of the H500. For a description of each bottom
Figure 22. H500 bottom panel
Table 24. H500 bottom panel elements

No.
Item Name
Description
USB port
Optional USB connector (refer to About Peripheral Devices

and Appendix A: AP Support for Bluetooth Low Energy
Devices).
LAN4 port
10/100 RJ-45 Ethernet Port.
LAN3 port
LAN2 port
LAN1+PoE port 10/100 RJ-45 LAN port with PoE out. Supports 802.3af PSE
Class 2 or 3 (depending on power input; refer to About
Peripheral Devices).
48VDC port
Optional 48VDC power input connector.
51

Reset Buttons
Figure 23 shows and Table 25 describes the reset buttons on the side of the H500.
Figure 23. H500 side panel reset buttons
Table 25. H500 side panel elements

No.
Item Name
Description
Soft Reset and

Hard Reset
buttons
The two reset buttons on the side of the H500 are used to
reboot or factory reset the AP.
Use a straightened paper clip to press and release the Soft Reset button for
eight seconds or more to reset the AP to factory defaults.
Use a straightened paper clip to press and hold the Hard Reset button to reboot
the AP. This is the same as removing power and then and restoring power to the
H500.
CAUTION! Resetting the AP to factory default settings erases all previously
configured settings.
52

ZoneFlex R300 AP
The R300 is a high-capacity, high-performing, two-stream, dual-band, 802.11n AP
with adaptive antenna technology for carriers and enterprises.
controllers.
The R300 AP requires a minimum of AP base image 100.0.0 and later to operate,
or SCG 2.5 and later, vSZ 2.5 and later, SmartZone software 3.2 and later, or ZD
The R300 includes five LEDs on its front panel and buttons and connectors on its
rear panel.
NOTE The R300 is an entry level 802.11n dual-band AP that does not support the
Smart Mesh or Spectrum Analysis features, and supports a maximum of 250
unencrypted clients.
Front Panel
Figure 24 shows the top view of the R300. For a description of each front panel
Figure 24. R300 top view
53

Table 26. R300 front panel elements

LED
Description
PWR LED
Off: Off.
Green: On.
OPT LED
DIR LED
Off: The AP is not being managed by ZoneDirector

(standalone mode).
2.4G LED (WLAN)

associated.
Amber: The WLAN service is up and no clients are associated.
5G LED (WLAN)

associated.
Amber: The WLAN service is up and no clients are associated.
54

Rear Panel
The rear panel of the R300 includes one 10/100/1000 PoE Ethernet port, power
socket and reset button. See Table 27 for a description of each rear panel part.
Figure 25. R300 rear panel
Table 27. R300 rear panel elements

Number Item Name
Description
10/100/
1000+PoE Port

RST Button

erases all previously configured settings.
Power

socket. Power can also be supplied via the 10/100/1000
PoE port.
55

ZoneFlex R500 AP
The R500 is a high-performance 2x2:2 802.11ac dual-band AP.
controllers.
or SCG 2.5.1 and later, vSZ 3.0 and later, SmartZone software 3.2 and later, or ZD
rear panel.
Front Panel
Figure 26 shows the top view of the R500. For a description of the front panel LEDs,
refer to Table 28.
56

Table 28. R500 front panel LEDs

LED
Description
PWR
Off: Off.
Green: On.
DIR

mode).
with ZoneDirector.
AIR

uplink AP is fair.
uplink.
2.4G

57

Table 28. R500 front panel LEDs (Continued)

LED
Description
5G

associated.
associated.
58

Rear Panel
The rear panel of the R500 includes one 10/100/1000 PoE Ethernet port, 10/100/
1000 Ethernet port, power socket and reset button. See Table 29 for a description
of each rear panel part.
Table 29. Rear panel element descriptions

No.
Label
Description
RESET
Button
Pressing, and then quickly releasing this button reboots the AP.
Pressing and holding it for six seconds resets the AP to factory
default settings.
CAUTION! Resetting the AP to factory default settings erases all
settings that you configured previously.

2
PoE Port

802.3af/at) connection. (The R500 is a Class 3 device.)
Ethernet
Port
One RJ-45 port for a 10/100/1000 connection.
59

Table 29. Rear panel element descriptions (Continued)

No.
Label
Description
12VDC
Connect the power adapter (12 VDC/1.25A) to this socket. Power

can also be supplied via the 10/100/1000 PoE port.
Table 30. Behavior of Ethernet port LEDs on the R500

LEDs
Description
Off
Not connected
Amber + Green
Amber
Green
WARNING! For units using Power over Ethernet (PoE). These products and all
802.3af Standard.
60

ZoneFlex R600 AP
The R600 is a high-performance 3x3:2 802.11ac dual-band AP.
controllers.
rear panel.
Front Panel
Figure 28 shows the top view of the R600. For a description of the front panel LEDs,
refer to Table 31.
61


LED
Description
PWR
Off: Off.
Green: On.
DIR

mode).
with ZoneDirector.
AIR

uplink AP is fair.
uplink.
2.4G

62


LED
Description
5G

associated.
associated.
63

Rear Panel
Table 32. Rear panel element descriptions

No.
Label
Description
RESET
Button
Pressing, and then quickly releasing this button reboots the AP.
Pressing and holding it for six seconds resets the AP to factory
default settings.
CAUTION! Resetting the AP to factory default settings erases all
settings that you configured previously.

2
PoE Port

802.3af/at) connection. (The R600 is a Class 3 device.)
Ethernet
Port
64

Table 32. Rear panel element descriptions (Continued)

No.
Label
Description
12VDC
Connect the power adapter (12 VDC/1.25A) to this socket. Power

can also be supplied via the 10/100/1000 PoE port.

LEDs
Description
Off
Not connected
Amber + Green
Amber
Green
802.3af Standard.
65

ZoneFlex R700 AP
The R700 is a high-capacity, high-performance, three-stream, 802.11ac dual-band
AP with adaptive antenna technology for carriers and enterprises.
controllers.
rear panel.
Front Panel
Figure 30 shows the top view of the R700. For a description of each front panel
66

Table 34. R700 front panel elements

LED
Description
Power LED
Off: Off.
Green: On.
DIR LED

mode).
with ZoneDirector.
AIR LED
Off: The AP is operating as a Standalone or Root AP (RAP), or as

a non-mesh AP.
uplink AP is fair.
uplink.
2.4GHz LED

67

Table 34. R700 front panel elements (Continued)

LED
Description
5GHz LED

associated.
associated.
Rear Panel
1
2
68


Number Item Name
Description
ETHERNET +
PoE Port

Ethernet, 802.3af/at) connection. (The R700 is a Class 3
device.)
ETHERNET
Port
12V 1.5A Power Connect the power adapter (12 VDC/1.25A) to this socket.
Socket
Power can also be supplied via the ETHERNET + PoE port.
RESET Button

erases all settings that you configured previously.

Table 36. Behavior of Ethernet port LEDs on R700
LEDs
Description
Off
Not connected
Amber + Green
Amber
Green
802.3af Standard.
69

ZoneFlex R710 AP
The R710 is a high-capacity, high-performance, four-stream, 802.11ac Wave 2,
dual-band AP with adaptive antenna technology for carriers and enterprises.
The R710 has a USB port on its bottom panel. The USB port is intended for lowpower devices such as BLE (Bluetooth low energy) beacons. The maximum
power that the USB port can supply is 0.5W. Refer to Appendix A: AP Support
for Bluetooth Low Energy Devices for more information.
The R710 can use the link aggregation control protocol (LACP) to control the
bonding of two 1Gbps physical Ethernet ports together to form a single logical
channel. Refer to Appendix B: Configuring Link Aggregation (LACP) for AP
Backhaul for instructions on bonding the two Ethernet ports using LACP.
controllers.
or SmartZone software 3.1.1 and later, or ZD 9.12 and later to operate.
NOTE The R710 is not supported by the ZoneDirector 1100.
The R710 includes five LEDs on its front panel, and buttons and connectors on its
bottom panel.
70

Front Panel
Figure 32 shows the front view of the R710. For a description of the front panel
LEDs, refer to Table 37.
Figure 32. R710 front view

No.
LED
Description
5
(GHz) Amber: The WLAN is up, but no clients or downlink MAPs are
Slow flashing green (one flash every two seconds): The WLAN is up
and at least one downlink MAP is connected. No clients are
associated.
Fast flashing green (two flashes every second): The WLAN is up, at
least one downlink MAP is connected, and at least one client is
associated.
2.4
(GHz) Green: The WLAN is up and at least one client is associated.
71


No.
LED
Description
AIR
Off: The AP is operating as a Standalone or Root AP (RAP), or as a

non-mesh AP.
Fast flashing green (two flashes every second): The AP is functioning
as a Mesh AP (MAP), and the wireless signal to its uplink AP is fair.
Slow flashing green (one flash every two seconds): Mesh networking
is enabled, but the AP is still searching for a mesh uplink.
CTL
Off: The AP is not being managed by a Ruckus Wireless controller

(standalone mode).
Green: The AP is being managed by a Ruckus Wireless controller.
managed by a Ruckus Wireless controller, but is currently unable to
communicate with the controller.
managed by a Ruckus Wireless controller and is currently receiving
PWR Off: Off.

Green: On.
Bottom Panel
The bottom panel of the R710 includes the following:
one 10/100/1000 PoE In Ethernet port
one 10/100/1000 Ethernet port
one 12VDC 2A power socket
one reset button
one USB port
See Table 38 for a description of each rear panel part, and see Table 39 for a
description of the Ethernet port LEDs.
72

Figure 33. R710 bottom panel

No. Item Name
Description
Ethernet (eth1)
Port
RJ-45 port for a 10/100/1000 connection.
Ethernet + PoE
(eth0) Port
RJ-45 port for a 10/100/1000 with PoE in.
NOTE: The R710 can be powered by a 802.3at-compliant

(25.5W) Power over Ethernet (PoE) switch or PoE injector.
--OR-an 802.3af-compliant PoE switch or PoE injector.
CAUTION: The AP can operate off of 802.3af power, but the
feature set is reduced: the USB port is disabled, the non-PoE

(eth1) Ethernet port is disabled, and the 2.4 GHz transmit power
is reduced from 28dBm to 25dBm (aggregate of spatial
streams), and country limits apply.
(The R710 is a Class 4 device when powering the USB port.)
WARNING! For units using Power over Ethernet (PoE). These
products and all interconnected equipment must be installed
indoors within the same building, including the associated
LAN connections, as defined by Environment A of the IEEE
802.3af Standard.
73

Table 38. R710 rear panel elements (Continued)

No. Item Name
Description
Connect a customer-ordered Ruckus Wireless 12VDC 9021169-xx00 AC power adapter (sold separately). When powered
by the 902-1169-xx00 power adapter, the R710 supports a full
feature set.
12V 2A Power
Socket
(Power can alternately be supplied via the Ethernet + PoE port.)

4
RESET Button
Pressing, and then quickly releasing this internal button reboots

the AP. Pressing and holding it for six seconds resets the AP to
factory default settings.
CAUTION! Resetting the AP to factory default settings erases
all settings that you configured previously.
USB Port
The R710 can have a low-power (0.5W or less) customersupplied USB device plugged in. The USB device is hidden after
the R710 is attached to its mounting base.

LEDs
Description
Off
Not connected
Amber + Green
Amber
Green
74
Installing the AP
In this chapter:
Before You Begin
Step 1: Preconfiguring the AP
Step 2: Verifying AP Operation
Step 3: Deploying the AP
Troubleshooting the Installation
7055 Physical Installation
H500 Physical Installation
75
Installing the AP
Before You Begin
Before You Begin

Before starting with the installation, make sure that you have the required items for
the installation ready. In addition, verify that the wireless stations on the network
have the required components for wireless communication with the AP.
This section describes the pre-installation tasks that you need to perform:
Performing a Site Survey
Preparing the Required Hardware and Tools
Determining the Optimal Mounting Location and Orientation
Performing a Site Survey

Before installing the AP, perform a site survey to determine the optimal AP placement
for maximum range, coverage, and network performance. Ruckus Wireless Support
can supply Site Survey best practices information. When performing a site survey,
consider the following factors:
Data rates: Range is generally inversely proportional to data rates. The maximum
radio range is achieved at the lowest workable data rate. Higher data rates are
generally achieved at closer distances.
Antenna type and placement: Proper antenna configuration is a critical factor in
maximizing radio range. As a general rule, radio range is increased by mounting
the antennas higher off of the ground.
Physical environment: Clear or open areas provide better radio range than
crowded or filled areas. The less cluttered the operating environment, the greater
the wireless range.
Obstructions, building materials, and sources of interference: Physical obstructions, such as concrete pillars, steel beams and filing cabinets can block or hinder
wireless communication. Avoid installing the AP in a location where there is an
obstruction between sending and receiving devices. A number of machines and
electronic devices that emit radio waves cranes, wireless phones, microwave
ovens, and satellite dishes interfere with and block wireless signals. Building
materials used in construction also influence radio signal penetration. For
example, drywall construction permits greater range than concrete blocks.
For more AP placement guidelines, refer to Determining the Optimal Mounting
Location and Orientation.
76
Installing the AP
Before You Begin
Preparing the Required Hardware and Tools

You must supply the following tools and equipment:
A notebook computer running Windows (2000/XP/Vista/7) or Mac OS X with an
Internet browser and one wireless 802.11a/b/g/n network card and one Ethernet
card installed.
A modem (DSL or cable), router, or other device provided by your Internet Service
Provider, that brings Internet access to your site.
(Optional) A network switch or a DSL/Internet gateway device.
Two Ethernet cables (Cat5e or better for PoE in)
(Optional) An AC power adapter (sold separately),
--or-(Optional) an 802.3af or 802.3at -compliant Power over Ethernet (PoE) switch
or PoE injector.
NOTE If the AP is deployed with SCG, SZ, vSZ or ZD controllers, or with SAMs
controllers, then follow the instructions in the associated controller user documents
to connect the AP to your Ethernet network.
77
Installing the AP
Before You Begin
Determining the Optimal Mounting Location and

Orientation
The location and orientation that you choose for the AP play a critical role in the
performance of your wireless network. In general, Ruckus Wireless recommends
installing the AP away from obstructions and sources of interference and ensuring
that the top of the AP is pointing in the general direction of its wireless clients.
Figure 34. Recommended ceiling mounting orientation
Limited
Reach
Limited
Reach
Excellent
Reach
Excellent
Reach
Excellent
Reach
78
Installing the AP
Before You Begin
When wall mounted, the APs should be staggered to maximize coverage.

Figure 35. Recommended wall mounting orientation
Excellent
Reach
Limited
Reach
Excellent
Reach
Excellent
Reach
79
Installing the AP
Before You Begin
Figure 36. Recommended wall mounting in a corridor (top view)
Limited
Reach
Excellent
Reach
Excellent
Reach
Limited
Reach
Excellent
Reach
Limited
Reach
Excellent
Reach
80
Installing the AP

NOTE The 100.0.0 and later APs are shipped from the factory with an AP base
image, which supports standalone AP and FM-managed operation, and which does
not support SCG, SZ, vSZ, ZD (or SAMs) controller operation.
After you have configured the AP with the base image as described in the following
sections, the AP automatically goes out and finds any operator-defined SCG, SZ,
vSZ, ZD (or SAMs) controllers. If the AP finds a controller that is configured to
automatically recognize the AP, then the controller downloads the controller-specific
AP firmware. If the AP does not find an SCG, SZ, vSZ, ZD (or SAMs) controller, then
it retains its base image AP firmware.
NOTE If the AP has been configured with SCG or ZD controller-specific AP
firmware, then it retains that image after a factory reset. To replace a controllerspecific AP image with the standalone AP firmware, please select the AP and
download the specific AP image at
https://support.ruckuswireless.com/#products_grid
The procedure for completing the APs basic configuration depends on whether you
want it to be managed by SCG or ZD, or FM or to operate as a standalone AP. Refer
to the section that is relevant to your deployment:
Configuring the AP for Management by an SCG, SZ or vSZ Controller
Configuring the AP for Management by ZD
Configuring the AP for Standalone Operation or for Management by FM
Configuring the AP for Management by an SCG, SZ or

vSZ Controller
When your Ruckus Wireless network is managed by an SCG, SZ or vSZ controller,
you can manage APs using the controller rather than individually logging into each
APs Web interface. If SCG, SZ or vSZ controllers are installed on the network, then
follow the SCG, SZ or vSZ instructions to configure the controller, and then connect
the AP to your network. The AP finds the SCG, SZ or vSZ and then downloads the
SCG-, SZ- or vSZ-compatible AP image from the controller.
NOTE The AP must have some way of obtaining an IP address (IPv4 DHCP or IPv6
Auto Configuration).
81
Installing the AP

When your Ruckus Wireless network is managed by a ZD controller, you can
manage APs using the controller rather than individually logging into each APs Web
interface. If ZoneDirector is installed on the network, then follow the instructions in
the ZoneDirector User Guide and connect the AP to your network. The AP finds the
ZD, and then downloads the ZD-compatible AP image from the controller.
Configuring the AP for Standalone Operation or for

Management by FM
This section describes the steps you need to complete to set up the AP in standalone
mode or to be managed by a Ruckus Wireless FlexMaster server, if you have one
installed on the network. Continue with the following:
1. Collecting the Required Materials
2. Preparing the Administrative Computer
3. Connecting the AP to the Administrative Computer
4. Logging Into the APs Web Interface
5. Configuring the Wireless Settings
6. Disconnecting the AP from the Administrative Computer
7. Restoring the Administrative Computers Network Settings (Optional)

Before starting with the configuration task, make sure that you have the following
requirements ready:
An administrative computer (notebook computer) with an Ethernet port and a
wireless card installed.
A Web browser such as Chrome 39 or 40, Firefox 3.3 or later, or Internet
Explorer10.0 or later installed on the administrative computer.
One Cat5e foil screened twisted pair (FTP) solid Ethernet cable.
82
Installing the AP
2. Preparing the Administrative Computer

NOTE The following procedure is applicable if the administrative computer is
running Windows XP or Windows 7. If you are using a different operating system,
refer to the documentation that was shipped with your operating system for
information on how to modify the computers IP address settings.
1 On your Windows XP or Windows 7 computer, open the Network Connections
(or Network and Dial-up Connections) control panel according to how the Start
menu is set up:
On Windows XP, click Start > Control Panel > Network Connections.
On Windows 7, click Start > Control Panel > Network and Internet >
Network and Sharing Center > Change Adapter Settings.
2 When the Network Connections window appears, right-click the icon for Local
Area Connection, and then click Properties.
NOTE Make sure that you configure the Local Area Connection Properties, not the
Wireless Network Connection Properties.
3 When the Local Area Connection Properties dialog box appears, select Internet
Protocol (TCP/IP) (TCP/IPv4 in Windows 7) from the scrolling list, and then
click Properties. The Internet Protocol (TCP/IP) Properties dialog box appears.
4 Write down all of the currently active network settings. You will need this
information later when you restore your computer to its current network
configuration.
5 Click Use the following IP address, and then configure the IP address settings
with the values listed in Table 40. For a sample configuration, refer to Figure 37.
Table 40. Configure your computers IP address settings
IP address
192.168.0.22 (or any address in the 192.168.0.x networkwith

the exception of 192.168.0.1, which is the default IP address
assigned to the AP)
Subnet mask
255.255.255.0
NOTE: You can leave the Default Gateway and DNS server fields blank.
6 Click OK to save your changes and close the TCP/IP Properties dialog box.
7 Click OK again to close the Local Area Connection Properties dialog box.
83
Installing the AP
Windows saves the IP address settings that you have configured.

Figure 37. Sample configuration in the Internet Protocol (TCP/IP) Properties dialog box
3. Connecting the AP to the Administrative Computer

CAUTION! Do NOT connect the AP to your live network at this point. If you connect
it to a live network with an active DHCP server, the AP acquires a new IP address
from DHCP and you are unable to access it via the default IP address (192.168.0.1).
1 Connect one end of an Ethernet cable to an Ethernet port on the AP, and then
connect the other end to the administrative computers Ethernet port.
2 Provide power to the AP using either an AC adapter or a PoE injector or switch.
4. Logging Into the APs Web Interface

1 On the administrative computer, open a Web browser window.
2 In the address or location bar, type the following address:
https://192.168.0.1
3 Press <Enter> on the keyboard to connect to the APs Web interface. A security
alert message appears.
4 Click Yes or OK or Proceed anyway (depending on the browser) to continue.
The APs login page appears.
84
Installing the AP
Figure 38. The Ruckus Wireless AP login page
5 In User name, type super.

6 In Password, type sp-admin.
7 Click Login. The Web interface appears, displaying the Status > Device page.
8 Continue to 5. Configuring the Wireless Settings below.
5. Configuring the Wireless Settings

To complete this step, configure the settings on the Common tab and at least one
Wireless # (WLAN Number) tab. These are the essential wireless settings that
enable wireless devices on the network to associate with the AP.
For your reference, the default wireless settings for the WLANs are listed in Table 41.
Table 41. Default WLAN wireless settings
Setting
Default Value
SSID (network name)
Wireless 1 to Wireless 8 (2.4 GHz Radio)

Wireless 9 to Wireless 16 (5 GHz Radio - only
available on dual radio APs)
Encryption (security)
Disabled on all WLANs
Default management IP address
192.168.0.1
85
Installing the AP
Configuring Common Wireless Settings

1 On the left menu of the Web interface, click Configuration > Wireless (Radio
2.4G or Radio 5G on dual-band APs). The Configuration > Common page
appears.
NOTE For dual-band APs (7055, 7363, 7372, 7982, H500, R300, R500, R600,
and R700), the two radios (2.4GHz and 5GHz) need to be configured separately on
the Web interface. To configure the common wireless settings, click Configuration
> Radio 2.4G or Configuration > Radio 5G. The rest of the configuration
procedures are the same as for single-band models.
Figure 39. The Configuration > Radio 5G > Common tab
2 Verify that the common wireless settings are configured as listed in Table 42.
Table 42. Common wireless configuration
Setting
Wireless Mode
Recommended Value
For ZoneFlex 7321, select 2.4GHz or 5GHz mode.
For other APs, the wireless mode is determined by the radio band
(Wireless 2.4G or Wireless 5G).
Channel
SmartSelect.
86
Installing the AP
Table 42. Common wireless configuration (Continued)

Setting
Recommended Value
Country Code
If you purchased the AP in the United States, this value is fixed to

United States at the factory and is not user configurable.
If you purchased the AP outside the United States, verify that the
value is set to your country or region. Selecting the correct country
code ensures that the AP uses only the radio channels allowed in
your country or region.
Note for dual-band AP users: The two radios on dual-band APs are
always configured with the same country code setting. If you change
the country code for Radio 1, for example, the same change is
automatically applied to Radio 2.
3 If you made any changes to the Common tab, click Update Settings.
4 Continue with Configuring Wireless # (WLAN number) Settings below.
Configuring Wireless # (WLAN number) Settings

1 Click one of the Wireless # (WLAN number) tabs.
Figure 40. The Configuration > Radio 5G > Wireless 9 tab
2 In Wireless Availability, click Enabled.

3 In Broadcast SSID, click Enabled.
87
Installing the AP
4 Clear the SSID box, and then type a unique and descriptive name that you want
to call this wireless network.
For example, you can type Ruckus Wireless AP. This SSID is the name that
helps users identify this wireless network in their wireless network connection
application.
NOTE You may also configure other wireless settings on this and other Wireless #
tabs (in addition to the settings described above), although it is not necessary for
completing the AP installation.
5 Click Update Settings.
You have completed configuring the basic wireless settings of the AP.
(Optional) Setting the FlexMaster Server Address

When you have a FlexMaster server installed on the network and you intend to use
FlexMaster to manage the AP, you can set the FlexMaster server address at this
point. Before starting this procedure, make sure you obtain the correct FlexMaster
server URL.
NOTE In addition to setting the FlexMaster server URL manually on the AP, you
can also use DHCP Option 43 or DNS to point the AP to the FlexMaster server. For
more information, refer to the FlexMaster User Guide.
1 On the menu, click Administration > Management.
2 Scroll down the page to the TR069 / SNMP Management Choice section.
88
Installing the AP
Figure 41. Type the FlexMaster server URL
3 Verify that the Auto option is selected.

4 In FlexMaster Server URL, type the URL of the FlexMaster server on the network.
You can use either http or https to connect to the URL and include either the
host name or IP address of the FlexMaster server in the URL. The following are
examples of valid FlexMaster server URLs:
http://flexmaster/intune/server
https://flexmaster/intune/server
http://192.168.20.1/intune/server
https://192.168.20.1/intune/server
5 Click Update Settings to save your changes.
You have completed setting the FlexMaster server address on the AP.
NOTE Instructions on how to verify that the AP and FlexMaster can communicate
with each other are provided in Checking the TR069 Status (FlexMaster
Management Only).
89
Installing the AP
6. Disconnecting the AP from the Administrative Computer

1 Disconnect the AP from the power source.
2 Verify that the power LED on the AP is off.
3 Disconnect the Ethernet cable from the administrative computers Ethernet port.
7. Restoring the Administrative Computers Network

Settings (Optional)
1 On your Admin computer, open the Network Connections (or Network and
Dial-up Connections) control panel according to how the Start menu is set up:
On Windows 7, click Start > Control Panel > Network and Internet >
Network and Sharing Center > Change Adapter Settings.
On Windows XP, click Start > Control Panel > Network Connections.
2 When the Network Connections window appears, right-click the icon for Local
Area Connection, and then click Properties.
3 When the Local Area Connection Properties dialog box appears, select Internet
Protocol (TCP/IP) (TCP/IPv4 in Windows 7) from the list, and then click
Properties. The TCP/IP Properties dialog box appears.
4 Restore the computers network settings by typing the original IP address
settings in the TCP/IP Properties dialog box.
5 On the TCP/IP Properties dialog box, click OK to close it.
6 Click OK again to close the Local Area Connection Properties dialog box.
You are now ready to connect the AP to your network.
90
Installing the AP

Before deploying the AP in your environment, Ruckus Wireless strongly recommends that you verify that the AP is operating correctly. To do this, connect the AP
to your live network temporarily and make sure that the network connection works
and that wireless clients are able to associate with the AP and connect to your
network and the Internet.
NOTE The network and power connections that you make in this step are
temporary.
Connecting the AP to the Network
Associating a Wireless Client with the AP
Checking the LEDs
Checking the TR069 Status (FlexMaster Management Only)
Disconnecting the AP from the Network
Connecting the AP to the Network

1 Connect the Ethernet cable from a LAN (RJ-45) port on the AP to your networks
router or switch.
2 Reconnect the AP to a power source.
You have completed connecting the AP to your live network. Perform the tasks
described in the following sections to verify that the AP is operating normally.
Associating a Wireless Client with the AP

1 On the administrative computer, verify that the wireless interface is enabled. On
Windows XP, click All Programs > Connect To > Wireless Network
Connection to enable the wireless interface. (Other operating systems are
similar).
2 Connect your admin computer to the wireless network:
Windows XP: In the system tray, right-click the
(Wireless Network Connection) icon, and then click View Available Wireless Networks.
Windows 7: Left click the
icon.
91
Installing the AP
3 In the list of available wireless networks, click the network with the same SSID
as you configured in Configuring Wireless # (WLAN number) Settings on
page 87. For example, if you set the SSID to Ruckus Wireless AP, click the
wireless network named Ruckus Wireless AP.
4 Click Connect.
Your wireless client connects to the wireless network.
Checking the LEDs

Perform a spot-check using the LEDs to verify that the AP is operating normally.
Refer to the following sections for information on how to check the LEDs on each
Ruckus Wireless AP model.
Single-Radio APs (7321/7352)

If the single-radio AP is operating normally and your wireless client was able to
associate with it:
The WLAN LED is green.
When you do not have Ruckus Wireless ZoneDirector on the network, the DIR
LED is off. This indicates that the AP is operating in standalone mode. If there is
a ZoneDirector device on the network, then the DIR LED is green.
Dual-Radio APs (7055/7363/7372/7982/H500/R300/R500/

R600/R700/R710)
If the dual-radio AP is operating normally and your wireless client was able to
associate with it:
The 2.4G or 5G LED is green.
When you do not have Ruckus Wireless ZoneDirector on the network, the DIR
LED is off. This indicates that the AP is operating in standalone mode. If there is
a ZoneDirector device on the network, then the DIR LED is green.
92
Installing the AP
Checking the TR069 Status (FlexMaster Management

Only)
If you configured the AP to report to a FlexMaster server on the network, make sure
you verify that it can successfully communicate with the FlexMaster server. You can
do this by checking the TR069 status on the APs Web interface.
1 Log in to the APs Web interface.
2 Go to the Administration > Management page.
3 Scroll down to the TR069 Status section.
4 Check the value for Last Successful Contact. If it shows a date in green, this
indicates that the AP was able to successfully communicate with FlexMaster.
Disconnecting the AP from the Network

1 Disconnect the AP from the power source.
2 Disconnect the Ethernet cable that runs to the APs RJ45 port from your
networks router or switch.
You are now ready to deploy the AP in its permanent mounting location.
93
Installing the AP

In this step, you place the AP in a suitable location on the network and connect it
to a power source and to your network environment. Continue with the following:
1. Choosing a Location for the AP
2. Connecting the AP to a Power Source and the Network
1. Choosing a Location for the AP

You can install the AP on a flat surface (for example, on a desktop or tabletop) or
mount it on a wall or ceiling. When choosing a location for the AP, ensure that the
location:
Allows easy viewing of the LEDs and access to the connectors, if necessary.
Is centrally located to the wireless clients that are connecting to the AP. A suitable
location might be on top of a cabinet or similar furniture to optimize wireless
connections to clients in both horizontal and vertical directions, allowing wider
coverage.
When positioning your AP, ensure that:
It is out of direct sunlight and away from sources of heat.
Cabling is away from power lines, fluorescent lighting fixtures, and sources of
electrical noise such as radios, transmitters and broadband amplifiers.
There are no thick walls or metal shielding between the AP and the wireless
stations.
Water or moisture cannot enter the case of the unit.
Air flow around the unit and through the vents in the side of the case is not
restricted.
Review the recommendations in Determining the Optimal Mounting Location and
Orientation on page 78 for help in choosing a suitable location for the AP.
94
Installing the AP
2. Connecting the AP to a Power Source and the

Network
Once you have placed the AP at its installation location, you are ready to connect
it to a power source and the network.
NOTE If your AP model supports PoE, you can also supply power to the AP from
a PoE switch or injector. For information on how to make the PoE connections, refer
to the documentation that was shipped with the PoE switch or injector.
CAUTION! If you are using PoE, you must use a Cat5e or better Ethernet cable for
the PoE connection.
1 Connect the power jack to the power connector on the rear panel of your Ruckus
Wireless AP.
2 Connect the power adapter to a power source.
3 Obtain an Ethernet cable that is long enough to connect the AP to your networks
router, switch, or hub.
4 Connect one end to a LAN port on the AP, and then connect the other end to
your networks router, switch, or hub.
5 Verify that the power LED on the AP is green.
Congratulations! You have completed setting up the AP on your network. To learn
how to configure and manage the AP, continue reading the next chapters.
95
Installing the AP

If the startup sequence does not work, verify that the network name (SSID) and
security settings (if you enabled them) on the AP match the settings on your wireless
device.
Disconnect the AP from the power source, wait 5 seconds, reconnect it, and
then wait 60 seconds before attempting a reconnection.
Disconnect and reconnect the AP and the PC.
Replace the Ethernet cable with a new one if the relevant LAN port LED is not
illuminated. (LEDs in each port light up during a successful connection.)
If all else fails, you can reset the AP to its factory defaults (and start over).
1 Insert a straightened-out paper clip into the reset button hole.
2 Press and hold the Reset button for at least eight (6) seconds.
You can now reconnect your computer directly to the AP (as described in 3.
Connecting the AP to the Administrative Computer on page 84), and then start
over with installation, using the default network settings.
96
Installing the AP

This section describes the physical installation instructions for mounting the 7055
to an electrical outlet box.
CAUTION! The AP and all interconnected equipment must be installed indoors
within the same building, including the PoE powered network connection as
described by Environment A of the 802.3af standard.
CAUTION! Ensure that you use a Cat5e or better Ethernet cable to supply PoE
power and LAN connectivity running to the outlet box where the AP will be installed.
1 Prepare the electrical outlet box.
2 The 7055 can be mounted to a variety of commonly used electrical outlet box
formats, including US style outlet boxes conforming to NEMA-WD6, and EU style
outlet boxes conforming to BS 4662.
NOTE The 7055 comes with a bracket for a single 1-gang electrical outlet box.
For adjacent outlet boxes, use the optional Ruckus Wireless ZF7055 adjacent wall
bracket kit (part number 902-0111-000).
Remove the outlet box cover from the outlet box, retaining the original box
cover screws.
Align the mounting bracket with the outlet box so that the screw holes line
up (the bracket provides multiple holes for different outlet box designs), and
Pull the Ethernet cable through the center of the mounting bracket.
Affix the mounting bracket to the outlet box using the original outlet box cover
screws. If the original outlet box screw heads extend over 2mm from the
bracket, then use the enclosed low profile mounting screws instead.
Run the required cables through the electrical outlet box allowing sufficient
slack for the cables to reach the not yet installed 7055.
3 Connect the cables.
Connect an Ethernet cable providing PoE power and network connectivity
to the PoE In LAN / Uplink port using either a standard RJ45 connector or
the 110 punch-down block (refer to Using the 110 Punch Down Block).
If PoE power is not available, the AP can be powered using an optional DC
power adapter (Ruckus part No. 902-0170-XX10, sold separately)
97
Installing the AP
If required, connect the cable providing support for pass-through devices to

the Pass Through port.
NOTE The status LEDs are intentionally not visible once the 7055 is mounted.
Complete any verification or troubleshooting that requires visibility of the LEDs before
mounting.
Figure 42. Attach 7055 AP cables before mounting to the bracket
4 Mount the AP to the bracket.

Snap the AP onto the mounting bracket by hooking the two locking tabs on
the bottom of the bracket into the slots on the bottom of the AP. Then push
the top of the AP in toward the wall until it snaps in place.
Use the two Torx bracket screws provided to secure the AP to the mounting
bracket using a T10 Torx screwdriver.
Figure 43. Secure the 7055 AP to the bracket using Torx screws
Torx
bracket
screws
98
Installing the AP
Using the 110 Punch Down Block

CAUTION! Do not connect both the Punch-down block and the Uplink port to a
network. Only one connection can be used at a time.
If you prefer to use the 110 Punch-down block connector rather than the RJ-45
connector for power and network connectivity, refer to the following diagram for
wiring details.
Figure 44. 7055 AP punch-down block wiring
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
99
Installing the AP

The 7441 DAS AP is intended for installation in an in-building distributed antenna
system (DAS) and can be co-located with other carrier or public safety services. The
7441 can be operated in standalone mode, or controlled by a ZoneDirector
controller or FlexMaster server. Continue with the following:
Distributed Antenna System Deployment
Antenna Gain and Cable Loss
Mounting Instructions
Distributed Antenna System Deployment

The 7441 is designed for indoor deployments where a distributed antenna system
provides benefits in coverage at the expense of client density and network capacity.
For example, in a multi-tenant building where tenants have their own corporate
wireless networks, a DAS can be used to provide access for building management,
visitors, building automation systems, etc.
There are several benefits of implementing Wi-Fi over DAS. For example, the
coverage area can be shaped more efficiently, resulting in fewer APs required to
adequately cover a given area.
Note however, that the DAS model contains some inherent limitations, including:
No MIMO (lower capacity)
Limited client capacity
Weak interference mitigation
Poor VoWLAN quality
No BeamFlex adaptive antenna technology
No mesh capability
Other 802.11 features may not work as designed over DAS
NOTE Ruckus Wireless supports all Ruckus hardware and software per the
customer's support agreement, but the Wi-Fi RF coverage and performance over
the DAS are the responsibility of the DAS vendor.
100
Installing the AP
The 7441 DAS AP can be installed in a variety of configurations, as designed by the

DAS vendor. For one example scenario in a multi-floor building, see Figure 45. DAS
systems typically require RF design using sophisticated RF modeling tools in order
to design effective Wi-Fi coverage on the DAS system. Detailed RF specs may be
secured on the Ruckus Support Site.
Figure 45. 7441 DAS AP installation example
101
Installing the AP
Antenna Gain and Cable Loss

Figure 46 provides an example of how to calculate antenna gain and cable loss.
Figure 46. 7441 Cable Loss and Antenna Gain
102
Installing the AP
Mounting Instructions
The 7441 mounting options include desktop, wall mounting (flat), wall mounting
(horizontal), and DIN rail mounting. Continue with one of the following:
Wall Mounting (Flat)
Wall Mounting (Horizontal)
DIN Rail Mounting
Grounding the AP
DIN Rail Removal
Wall Mounting (Flat)

1 Attach the wall mounting brackets to the 7441 as shown in Figure 47.
Figure 47. 7441 flat wall mount
2 Place the AP on the wall and mark the locations for screw holes.
3 Drill screw holes, place the AP onto the wall and insert screws.
Wall Mounting (Horizontal)

The 7441 can be mounted to a wall horizontally as shown in Figure 48.
103
Installing the AP
Figure 48. 7442 horizontal wall mount
1 Attach the brackets to the AP as shown in Figure 48.

2 Place the AP on the wall and mark the locations for screw holes.
3 Drill screw holes, place the AP onto the wall and insert screws.
DIN Rail Mounting

Use the DIN rail clip on the rear of the AP to connect mount to a DIN rail.
1 Remove the screw on the housing back wall and use to attach the DIN rail clip
to the rear of the AP as shown in Figure 49. The clip has a tab to prevent rotation
which fits into the corresponding slot in the housing.
Figure 49. 7441 DIN rail clip
2 Mount the AP to the DIN rail as shown in Figure 50.
104
Installing the AP
Figure 50. 7441 DIN rail mounting
Grounding the AP
1 Attach ground wire to the AP using the included terminal ring and two hex nuts
as shown in Figure 51. The terminal ring can accommodate wire sizes ranging
from 16 to 25 gauge.
Figure 51. Grounding the 7441 AP
DIN Rail Removal

A large, flat screwdriver inserted from the bottom of the product can be used to pry
the clip off the rail.
105
Installing the AP

Refer to the H500 Access Point Quick Setup Guide for physical installation instructions for initially configuring and mounting the H500 AP. You can download the
H500 Access Point Quick Setup Guide from the Ruckus Wireless Support website at
https://support.ruckuswireless.com
106
In this chapter:
Before You Begin: Preconfiguring the AP
When You Are Using a Dual-Band AP
107


NOTE APs are shipped from the factory with AP 100.x base image firmware, which
supports standalone and FlexMaster (FM) manager operation. The AP 100.x base
image does not support SmartCell Gateway (SCG), SmartZone (SZ), virtual
SmartZone (vSZ) or ZoneDirector (ZD) controller operation.
After you have configured the AP with the AP 100.2.0 base image as described in
the following sections, the AP can automatically search for an operator-defined
SCG, SZ, vSZ or ZD controller. When the AP finds the SCG, SZ, vSZ, or ZD controller
that is configured to automatically recognize the AP, the controller downloads the
required controller-compatible AP firmware, and the AP is now managed by that
controller. If the AP does not find an SCG, SZ, vSZ or ZD controller, then it retains
its AP 100.2.0 base image.
NOTE In the SCG, SZ, vSZ and ZD cases, after the AP base image is overwritten
with the controller-specific image and the AP no longer operates in standalone
mode, the AP retains its SCG-, SZ-, vSZ- or ZD-compatible image after reboot and
factory reset.
To replace a controller-compatible AP image with the AP 100.2.0 base image, please
select the AP and download the required AP image at
https://support.ruckuswireless.com/#products_grid
The procedure for completing the APs basic configuration depends on whether you
want it to be managed by an SCG, SZ, vSZ or ZD controller, or if you want it to
operate as a standalone AP with or without an FM manager. Refer to the section
that is relevant to your deployment:
Configuring the AP for Management by an SCG, SZ or vSZ Controller
Configuring the AP for Standalone Operation or for Management by FM
108

Configuring the AP for Management by an SCG, SZ or

vSZ Controller
When your Ruckus Wireless network is managed by an SCG, SZ or vSZ controller,
you can manage APs using the controller rather than individually logging into each
APs Web interface.
If SCG, SZ or vSZ controllers are installed on the network, then follow the SCG, SZ
or vSZ instructions to configure the controller, and then connect the AP to your
network. The AP finds the SCG, SZ or vSZ, and then downloads the SCG-, SZ- or
vSZ-compatible AP image from the SCG, SZ or vSZ controller.

When your Ruckus Wireless network is managed by a ZD controller, you can
manage APs using the controller rather than individually logging into each APs Web
interface.
If ZoneDirector is installed on the network, then follow the instructions in the
ZoneDirector User Guide and connect the AP to your network. The AP finds the
ZD, and then downloads the ZD-compatible AP image from the ZD controller.
109

Configuring the AP for Standalone Operation or for

Management by FM
NOTE DO NOT connect the AP to your live network at this point. If you connect it
to a live network with an active DHCP server, the AP acquires a new IP address
from the DHCP and you are unable to access it via the default IP address
(192.168.0.1).
This section describes the steps you need to complete to set up the AP in standalone
mode or to be managed by a Ruckus Wireless FlexMaster manager, if you have one
installed on the network. Continue with the following:

Before starting with the configuration task, make sure that you have the following
requirements ready:
An administrative computer (notebook computer) with an Ethernet port and a
wireless card installed.
A Web browser such as Chrome 39 or later, Firefox 33 or later, or Internet Explorer
10 or later installed on the administrative computer.
One Cat5e unshielded twisted pair (UTP) Ethernet cable.
2. Logging Into the Ruckus Wireless AP Web Interface

You can manage your AP with the integrated Web interface (which you already used
to configure basic AP parameters). If your Ruckus Wireless network is managed by
an SCG, SZ, vSZ or ZD controller, then you can manage APs using the controller
rather than individually logging into each APs Web interface.
NOTE The following procedure assumes that you know the static IP address of
the AP (now in use), or you have some means of determining the dynamic IP address
in use by the AP. The PC you use for AP administration should be on the
management VLAN, if VLANs are used in your network.
Refer to the AP installation or quick setup guide for instructions on how to connect
an administrative computer to the AP.
1 On the PC, open a Web browser window.
110

2 In the address or location bar, type the IP address of the AP. Default IP address
for standalone Ruckus Wireless APs:
192.168.0.1
3 Press <Enter> to connect to the Web interface.

4 If a Windows security alert dialog box appears, then click Yes or OK or Proceed
anyway (depending on the browser) to continue. The Ruckus Wireless Admin
login page appears.
5 In Username, type super.
6 In Password, type sp-admin.
7 Click Login.
The Ruckus Wireless AP Web interface appears.
111


You manage the AP through a Web browser-based interface that you can access
from any networked computer. Table 43 lists the Web interface features that are
identified in Figure 52.
Figure 52. Elements of the Ruckus Wireless AP Web Interface
2
3
4
Table 43. Ruckus Wireless AP Web interface elements

No. Element
Description
Menu
Under each category (Status, Configuration, etc.) are options that, when
clicked, open the related workspace in the area to the right.
Tabs
Contains additional options for the configuration page. For example, the
Configuration > Wireless page includes one tab for common wireless
configuration and eight tabs for each of the available WLANs.
LOGOUT Button
Click this button to log out of the AP.
Help Button
Click this button to open a help window with information related

specifically to the options currently displayed in the workspace.
Workspace
This large area displays features, options and indicators relevant to your
menu bar choices.
112


When your Ruckus Wireless AP model is dual-band, note that elements on the Web
interface menu are slightly different from single-band Ruckus Wireless AP models.
Dual-band APs have one 2.4GHz radio (for 802.11b/g/n clients) and one 5GHz radio
(for 802.11a/n clients). The wireless settings for these two radios need to be
configured separately, which is why the dual-band AP Web interface has the Radio
2.4G and Radio 5G menu items, instead of a single Wireless menu item in
single-band models.
Figure 53 highlights the differences between single-radio AP and two-radio AP
menus.
Figure 53. Menu items are slightly different in single-band APs (left) and dual-band AP models
(right)
113
Configuring the AP
NOTE If the AP has been configured with SCG, SZ, vSZ or ZD controllercompatible firmware, then the AP controller-compatible image is already installed
and configured; you have completed the AP installation. When you plan to manage
your Ruckus Wireless network using SCG, SZ, vSZ or ZD, refer to the associated
SCG, SZ, vSZ or ZD user documents, available from the Ruckus Wireless website at
http://support.ruckuswireless.com/documents
If the AP is to be run in a standalone configuration or is to be managed by a
FlexMaster manager, then continue with this section.
This chapter provides instructions for configuring Ruckus Wireless APs in a standalone configuration or when the AP is to be managed by a FlexMaster manager. In
this chapter:
Configuring Device Settings
Configuring Internet Settings
Configuring Local Subnets
Configuring Wireless Settings
Configuring Ethernet Ports
Configuring Hotspot Service
114
Configuring the AP

Device settings refer to the device name, location, service provider login and other
settings. (Some settings are only available on certain AP models.)
1 Select Configuration > Device. The Configuration > Device page appears.
Figure 54. The Configuration > Device page
2 In Device Name, type a new name for the device or leave as is to accept the
default device name (RuckusAP). The device name identifies the AP among
other devices on the network.
3 Optionally, enter Device Location and GPS Coordinates to keep track of the
physical location of the AP.
4 In Temperature Update (specific models only), enter the interval (in seconds) to
record the internal temperature of the device.
5 Under LED Control (specific models only), check the Disable Status LED(s) box
to turn off the status LEDs. This can be useful when the AP is installed in a public
location, to avoid drawing attention to the AP.
6 Under Service Provider Login, change the login information as required:
Username: Type the name that you want to use for logging into the Web
interface. The default user name is super.
Current Password: When you are changing the password, enter the existing
password here.
115
Configuring the AP
New Password: When you are changing the password, type the new
password that you want to use. The default password is sp-admin. The
password must consist of six to 32 alphanumeric characters only.
Confirm New Password: Retype the new password to confirm.
7 Under Login remote authentication, click the TACACS+ State box to enable
TACACS+ authentication, if required. Terminal Access Controller Access-Control
System Plus (TACACS+) is an AAA protocol used to authenticate administrator
login to this device. Users can be authenticated/authorized to monitor, operate
or configure this device. Default is disabled. Administrators can be assigned any
of the following three administration privilege levels:
Super Admin (Perform all configuration and management tasks)
Operator Admin (Change settings affecting single AP's only)
Monitoring Admin (Monitoring and viewing operation status only)
8 If TACACS+ server state is enabled, then configure the TACACS+ server settings:
TACACS+ server: IPv4 or IPv6 server address.
TACACS+ port: 49 is the default, but it can be set to any available TCP port.
TACACS+ Service: Login name.
Share Key: TACACS+ Password.
Confirm Share Key: TACACS+ Password.
9 Click Update Settings to save and apply your changes.
116
Configuring the AP

Internet settings define how the AP connects to your local area network and to the
Internet. This section describes how to view and configure the APs Internet settings.
Topics discussed include:
VLAN Settings Overview
Configuring NTP Server and Management VLAN
Default IP Addressing Behavior
Obtaining and Assigning an IP Address
Configuring L2TP Connection Settings
VLAN Settings Overview

A Ruckus Wireless AP is in many ways like a network switch with the capability to
service Wi-Fi connections. As such, like many advanced switches, Ruckus APs
conform to the IEEE 802.1Q standard -- the standard that defines virtual LANs. In
an 802.1Q switch, the concept of VLANs is always present. If a packet arrives
without an 802.1Q header, it is assigned to the native VLAN or untag VLAN.
Each of the APs wireless interfaces can be assigned a single VLAN. When a packet
enters the AP through its wireless interface, the packet is assigned to the Access
VLAN configured on the Configuration > Wireless page (by default, 1).
AP Ethernet ports however, can be configured to pass all VLAN traffic (Trunk Ports)
or multiple specific VLANs (General ports).
The VLAN displayed in the Web interface shows the APs view of the VLAN
environment; when a packet arrives at an APs Ethernet port, the ports VLAN
configuration helps determine if the packet is accepted or not (VLAN membership),
and assigns a default VLAN (untagged VLAN) if the packet contains no 802.1Q
header.
In general, if your network has VLANs deployed already, you should apply VLAN
configuration to Ruckus APs so that the configuration across the network is
consistent.
117
Configuring the AP
Configuring NTP Server and Management VLAN

NTP Server
A Network Time Protocol (NTP) Server should be configured to ensure that the AP
maintains the correct time. The default Ruckus Wireless NTP Server (ntp.ruckuswireless.com) can be used if you do not have an NTP server on your network.
If you want the AP to contact a different NTP server, you can do so by going to
Configuration > Internet and entering the host name in NTP Server at the top of
the page.
Management VLAN
CAUTION! Changing the Management VLAN causes you to be immediately
disconnected from the Web interface if the computer you are using is not on the
same VLAN. Do not change the Management VLAN unless your admin PC is on
the same VLAN, or you are disconnected and unable to connect again without
factory resetting the AP.
If you want to place this APs management traffic into a management VLAN, enter
the VLAN ID in the Management VLAN field and then click Update Settings.
Default IP Addressing Behavior

By default, the AP is configured to automatically obtain an IPv4 address from a
DHCP server on the network. If the AP does not detect a DHCP server, it
automatically assigns itself the static IP address 192.168.0.1 to make it easier
for you to preconfigure and deploy it on your network.
For IPv6, the Auto Configuration setting serves the same purpose as DHCP. The
default static IPv6 address is fc00::1.
Obtaining and Assigning an IP Address

There are three methods of assigning IP addresses to the AP:
DHCP / Auto Configuration
Configuring Static IP
Configuring PPPoE
118
Configuring the AP
DHCP / Auto Configuration

If you leave the AP at its default configuration, it attempts to obtain an IPv4 address
from a DHCP server on the network.
In an IPv6 network environment, the AP attempts to obtain an IPv6 address from
an IPv6 Auto Configuration server.
Renewing and Releasing DHCP

This task should be performed only if you have access to the DHCP server or have
some way to determine what IP address has been assigned to the AP. It serves as
a troubleshooting technique when IP addresses to one or more networked devices
are unusable or in conflict with others, or when the AP loses its DHCP-assigned IP
address for some reason.
1 Go to Status > Internet.
Figure 55. Renew or Release DHCP
2 Review the current settings.

3 If the current Connection Type is DHCP, you are able to see the currentlyassigned IP address and subnet mask listed below.
To force the AP to release its DHCP-assigned IP address, click Release
DHCP. This disconnects the user from Web interface as the system reverts
to its default IP address. Log in to the device using the default IP address
(192.168.0.1) and click on Renew DHCP to request a new lease from the
DHCP server.
119
Configuring the AP
Click Renew DHCP to request a new IP address lease from the DHCP server.
Note: The IP address may or may not change depending on the lease time
offered to this device.
4 Click Update Settings to save your settings.
Configuring Static IP
Unless you are able to determine the IP address assigned to the AP by the DHCP/
Auto Configuration server, it can be useful for anyone needing administrative access
to configure a static IP address.
1 Go to Configuration > Internet. The Configuration > Internet page appears.
Figure 56. The Configuration > Internet page
2 You can configure static addresses for IPv4, IPv6 or both. The AP maintains both
sets of IP address settings when both are configured.
Static IPv4
3 In IPv4 Connection Type, select Static IP.
4 When the Internet Connection Settings options appear, you can make changes
to the following settings:
IPv4 Address: Enter the static IP address that you want to assign to the AP
in IPv4 (dot-decimal) format.
IPv4 Subnet Mask: Enter the subnet mask for the network.
120
Configuring the AP
IPv4 Gateway: Enter the gateway IP address of the Internet interface.

5 To allow the DNS mode to be determined automatically, set IPV4 DNS Mode to
Auto.
To set the DNS mode manually, set IPV4 DNS Mode to Manual. Then enter the
following:
IPv4 Primary DNS Server: The IP address of the primary Domain Name
System (DNS) server.
IPv4 Secondary DNS Server: The IP address of the secondary DNS server.
6 Continue with Step 7 or Step 9.
Static IPv6
7 In IPv6 Connection Type, select Static IP.
8 When the Internet Connection Settings options appear, you can make changes
to the following settings:
IPv6 Secondary DNS Server: The IP address of the secondary DNS server.
IPv6 Address: Enter the static IP address that you want to assign to the AP
in IPv6 (colon-separated) format.
IPv6 Prefix Length: Enter the prefix length for the network.
IPv6 Gateway: Enter the gateway IP address of the Internet interface.
121
Configuring the AP
Configuring PPPoE
Point to Point Protocol over Ethernet (PPPoE) is a Layer 2 protocol which uses the
PPP (Point to Point) protocol to connect a client system to a server system over a
one to one network link. All traffic for a PPPoE connected client must go through
the PPPoE server to reach the client. A PPPoE server can therefore be used to
route, NAT, firewall, and perform QoS traffic shaping.
If a PPPoE server is used to distribute Internet access to subscribers, the AP can
be configured with a PPPoE username and password to authenticate with the
PPPoE server.
PPPoE is available only for the IPv4 connection type; PPPoE is not supported in
IPv6 environments.
1 Go to Configuration > Internet.
2 Under IPv4 Connection Type select PPPoE.
3 Enter a PPPoE Username.
4 Enter a PPPoE Password.
5 Retype the password in PPPoE Password Confirmation.
6 To allow the DNS mode to be determined automatically, set IPV4 DNS Mode to
Auto.
To set the DNS mode manually, set IPV4 DNS Mode to Manual. Then enter the
following:
IPv4 Secondary DNS Server (optional): The IP address of the secondary DNS
server.
Configuring L2TP Connection Settings

You can implement transparent bridging by using L2TP (Layer 2 Tunneling Protocol)
tunneling. By tunneling traffic from an AP to a centralized data center, access
controllers with policy enforcement software can apply rules and services. In a
typical WLAN implementation, these rules include a captive portal to authenticate
users credentials.
122
Configuring the AP
In the case of L2TP, the Ruckus Wireless AP functions as a remote bridge. As such,
it forwards traffic into PPP sessions over the L2TP tunnel. This implementation
ensures that you have complete visibility into MAC addresses of users, as individual
Wi-Fi clients are essentially placed (bridged) onto the ISPs core network.
1 Go to Configuration > Internet.
2 Under L2TP Connection, click Enable.
Figure 57. L2TP Connection
3 In L2TP Network Server IP Address, type the IP address of the L2TP network
server (LNS) to which the device connects.
4 In L2TP Network Server Password, type the L2TP server password.
5 If your network requires PPP authentication, configure the following fields under
L2TP/PPP Authentication:
Username: Type your PPP user name.
Password: Type the password for the account.
L2TP Tunnel Untag VLAN ID: Enter the Untag VLAN ID for the L2TP tunnel.
6 In Close WLAN When Tunnel Fail, select Enable if you want to disable the WLAN
when the tunnel connection is lost. This prevents clients from remaining
connected to the WLAN but without Internet connectivity.
123
Configuring the AP

Ruckus Wireless APs can be configured to provide routing/network address translation (NAT) functionality by using the Local Subnets feature. When a Local Subnet
is enabled, the standalone AP serves as a gateway router with the ability to manage
its own subnets, providing DHCP server and DNS cache functions for both wired
and wireless clients. These clients can be assigned private IP addresses from a userdefined address pool. Traffic from the client station in private address space appears
on the outside as if generated by the AP itself. In this way, the AP performs Layer 3
packet forwarding not only for Hotspot/WISPr usage, but for standard usage as well.
Up to four IP subnets can be configured per AP, each with its own address range
which cannot conflict with one another.
1 Go to Configuration > Local Subnets. The four tabs at the top (Local Subnet
1 - 4) allow you to configure each of the four subnets independently.
Figure 58. Configuring local subnets and enabling router mode
2 Click Enabled next to Subnet. The local subnet configuration options appear.
3 In Local IP Address, enter an IP address for the gateway. The default address
for Subnet 1 is 192.168.40.1. This address can be used to access the APs
Web interface for configuration and monitoring from devices connected to this
subnet.
124
Configuring the AP
4 In Subnet Mask, typically you would want to leave the setting at its default value
(255.255.255.0) for a Class C subnet with an address pool of up to 254
addresses. An error appears if you enter an invalid IP/netmask combination.
5 In DHCP Server, click Enabled if you want to enable DHCP for this subnet.
Starting Address and Maximum DHCP Users fields appear.
6 In Starting Address, enter an address in the same subnet as the Local IP Address
(e.g., 192.168.40.2).
7 In Maximum DHCP Users, enter the maximum number of clients that can be
assigned addresses by DHCP in this subnet (valid values are 1-253 if the default
subnet mask is used).
8 In Access VLAN, enter a VLAN ID to segment client traffic arriving from this subnet
from other network traffic. (Example: if you use the default 192.168.40.1 address
range, you may want to use 40 as the VLAN for this subnet.)
9 Click Update Settings to save your changes. The local subnet is created
immediately and can now be applied to WLANs or Ethernet ports from their
respective configuration pages.
125
Configuring the AP

This section describes how to configure the wireless settings of the AP. There are
two types of wireless settings that you need to configure:
Configuring Common Wireless Settings: Includes the wireless mode, country
code, and advanced wireless settings, such as the wireless transmit power and
wireless protection mode. These settings are applied to all WLANs.
Configuring Wireless # (WLAN Number) Settings: The Wireless # tabs (Wireless
1 through Wireless 8 on the 2.4GHz radio and Wireless 9 through Wireless
16 on the 5GHz radio) provide settings for customizing each WLAN individually.
Refer to the sections below for instructions on how to configure each set of wireless
settings:
Configuring Common Advanced Settings
Configuring Wireless # (WLAN Number) Settings
126
Configuring the AP

Common wireless settings are settings that are applied to all WLANs. On single
radio APs, go to Configuration > Wireless. On dual radio APs, you configure these
settings for the 2.4 GHz and 5 GHz radios independently by going to Configuration
> Radio 2.4G or Configuration > Radio 5G.
1 Go to Configuration > Wireless. The Configuration > Wireless > Common page
appears.
NOTE If you are using a dual-band AP, then go to Configuration > Radio 2.4G
or Configuration > Radio 5G.
Figure 59. The Configuration > Wireless > Common page
2 Make changes to the common wireless settings listed in Table 44.

Table 44. Common Wireless settings
Setting
Description
Radio Network
(Dual radio APs only) Allows you to change the name of the
2.4GHz and 5GHz radios (default: Radio 2.4G and Radio
5G).
127
Configuring the AP
Table 44. Common Wireless settings (Continued)

Wireless Mode
On 802.11b/g APs:
The wireless mode options include the following:
Auto-Select: Allows both 802.11g- and 802.11b-compliant
devices to connect to the network. This is the default setting.
2.4GHz 54 Mbps (For faster 802.11g devices only): Allows
only 802.11g-compliant devices to join the network.
2.4GHz 11Mbps (For slower 802.11b devices only): Allows
only 802.11b-compliant devices to join the network.
On dual radio 802.11n APs:

On dual radio 802.11n APs, the wireless mode is determined
by radio: For the 2.4GHz radio, the mode is set to 2.4GHz
(802.11b/g/n), while for the 5GHz radio, the mode is set to 5GHz
(802.11a/n).
On the 7321:
The 7321 is a single radio 802.11n AP capable of operating in
either 2.4 or 5GHz mode. Use this setting to select 2.4GHz or
5GHz mode. Refer to Band Selection on the 7321.
Channel
This option lets you select the channel used by the network. You
can choose SmartSelect, or choose one of a specific number
of channels. If you choose SmartSelect, the AP automatically
selects the best channel (encountering the least interference) to
transmit the signal.
Channel Width (11n

APs only)
On 802.11n APs, the option to choose 40MHz channel width

provides (theoretically) double the data capacity of a 20MHz
channel. However, wider channel width means fewer channels
available, and more interference with other wireless signals.
Country Code
This option (if enabled) lets you select your country or region
code.
CAUTION! Selecting the incorrect country or region may result in violation of
applicable laws. If you purchased the AP in the United States, you do not need to
set the country code manually. Ruckus Wireless devices that are sold in the US are
preconfigured with the correct country code and this setting is non-configurable.
Advanced Settings
Refer to Configuring Common Advanced Settings on

page 130.
128
Configuring the AP

AeroScout RFID
Select Enabled to support AeroScout RFID tag detection.
To check the status of the AeroScout communication agent

(which relays location data from AeroScout Tags to the
AeroScout Engine), go to the Status > Wireless page. Refer
to Viewing Common Wireless Settings for more information.
NOTE: For other AeroScout-related configuration, refer to
the AeroScout documentation that was shipped with your
AeroScout Tag and AeroScout Engine.
NOTE: If ZoneDirector exists on the network, then you can
enable AeroScout RFID tag detection on all its managed APs
at once. Refer to the ZoneDirector online help for more
information.
Ekahau RFID
Select Enabled to support Ekahau RFID tag detection, and

then enter the IP address and port number of the Ekahau Real
Time Location System Controller (ERC).
External Antenna
NOTE: This option only appears if you are using the 7372-E
AP.
The 7372-E AP provides an external antenna port which allows
you to attach an external antenna to extend the range of your
wireless network. To enable the AP to use the external antenna,
select the Enabled option in this section. This option is disabled
by default.
Band Selection on the 7321

The 7321 is a dual-band selectable (2.4 GHz or 5 GHz) single radio AP. This means
it can operate on the 2.4 GHz band or the 5 GHz band at any time, but not both at
the same time. You can select the radio band from the Configuration > Wireless
page, as shown in Figure 60.
129
Configuring the AP
Figure 60. The 7321 can be configured to operate in either 2.4GHz or 5GHz mode
Configuring Common Advanced Settings

Advanced wireless settings should only be changed by an experienced administrator. Incorrect settings can severely impact wireless performance. It is recommended that the default settings are retained for best performance.
NOTE To fully benefit from the APs capabilities, it is advisable not to change these
values unless absolutely necessary.
1 On the Configuration > Wireless page, click Advanced Settings: Edit Common
Settings. The Configuration > Wireless > Advanced > Common page appears.
NOTE If you are using a dual-band AP, go to Configuration > Radio 2.4G or
Configuration > Radio 5G > Edit Common Settings.
130
Configuring the AP
Figure 61. The Configuration > Wireless > Advanced > Common page
2 Configure the advanced settings listed in Table 45 as required.

Table 45. Advanced common wireless settings
Option
Description
Transmit
Power
The default setting is Full. Select the level of transmit power from the dropdown menu. This option sets the maximum transmit power level relative
to the predefined power (this value differs according to the current country
code).
Protection (Disabled by default.) If you activate protection, you control how 802.11
Mode
devices know when they should communicate with another device. This
is important in a mixed environment of both 802.11b and 802.11g/11n
clients.
CAUTION! Activating this option (and configuring the settings) boosts
the interoperability of 802.11b and 802.11g/11n devices but severely

decreases performance.
CTS-only: Choose this option to force all destination devices to
acknowledge their ability to receive data when a transmission is initiated.
Use this option for compliance with the Wi-Fi Alliance certification.
RTS/CTS: Choose this option to force both sending and receiving
devices to confirm a data exchange on both ends before proceeding.
3 Click Update Settings to save and apply the changes.
131
Configuring the AP
Configuring Wireless # (WLAN Number) Settings

The AP provides up to eight wireless LANs per radio that can be individually
configured to provide different kinds of services for different kinds of wireless clients,
traffic types or different user groups. Each WLAN can be configured with separate
security settings, VLANs, access controls and rate limiting policies, among other
settings.
1 Go to Configuration > Wireless (or Configuration > Radio 2.4G/Radio 5G).
The Configuration > Wireless > Common page appears.
2 Click one of the eight Wireless (#) tabs. The Configuration > Wireless > Wireless
[#] page appears.
Figure 62. Wireless # (WLAN number) settings
3 Review the WLAN options listed in Table 46, and then make changes as required.
Table 46. WLAN options
Option
Description
Wireless Network
This wireless network name is for management purposes only,

and is not visible to the user.
Wireless Availability
This option controls whether or not the wireless network is

available to users (Enabled or Disabled).
132
Configuring the AP
Table 46. WLAN options (Continued)

Broadcast SSID
This option controls whether or not the WLAN SSID is visible to

anyone looking for wireless networks. Disabling (hiding) the
SSID requires the user to be told the correct SSID before they
can connect to your network.
SSID
This is the publicly-broadcast name of your wireless network.

SSIDs can contain up to 32 alphanumeric characters and are
case-sensitive. The maximum SSID length can only contain
between 2 and 32 characters, including characters from ! (char
33) to ~ (char 126).
Threshold Settings
This button opens a page where you can configure the

Protection Mode you activated on the Configuration > Wireless
> Advanced > Wireless [#] page. If Protection Mode is not active,
ignore this option.
For more information, refer to Setting Threshold Options on
page 141.
Rate Limiting
This button opens a page where you can configure upload and
download limits per station. For more information, refer to Rate
Limiting on page 143.
Access Control
This button opens a page where you can configure access

controls for the WLAN. For more information, refer to
Controlling Access to the Wireless Network on page 144.

Packet Forward
Isolated: Selecting Isolated causes the traffic from this WLAN

to terminate at the AP.
Bridge to WAN: The default setting, Bridge to WAN forwards
packets arriving on this WLAN to the WAN (uplink) port and
eventually to their external destinations using Layer 2
forwarding.
Local Subnet NAT and Route to WAN: This setting allows
routing of wireless packets to their destinations using Layer 3
network address translation (NAT).
Bridge to L2TP Tunnel: Uses Layer 2 Tunneling Protocol to
deliver packets encapsulated with an L2TP header in UDP
datagrams.
133
Configuring the AP
Table 46. WLAN options (Continued)

Hotspot Service
Select a Hotspot configuration from the list to enable Hotspot

service on this WLAN, if you have configured it from the
Configuration > Hotspot page. See Configuring Hotspot
Service on page 152.
Local Subnet
This option appears if you have selected Local Subnet NAT and
Route to WAN under Packet Forwarding, and allows you to
choose which subnet this WLANs traffic is part of. You must
have previously configured a subnet from the Configuration >
Local Subnets page before it becomes available here.
Access VLAN
Enter a VLAN ID to segment all traffic arriving from this WLAN

to a specified VLAN. Default is 1.
Dynamic VLAN
This setting is available only with WPA encryption and 802.1X

authentication. Dynamic VLAN allows the dynamic assignment
of VLANs to clients based on RADIUS attributes. Enable this
option only if your RADIUS server is configured to segment
clients using dynamic VLAN.
Insert DHCP Option

82
When this option is enabled on an SSID, additional information

is encapsulated in DHCP option 82 and inserted into DHCP
request packets. Current format of option 82 is:
Circuit ID sub-option:
WLAN:<IFNAME>:<VLAN>:<SSID>:<MODEL>:
<HOSTNAME>:<DEVMAC>
This option supports the ability for a service provider to allocate
IP addresses intelligently by considering information on the
origin of the IP allocation request.
Client Fingerprinting
When this option is enabled, the AP attempts to identify client

devices by their operating system, device type and host name,
if available.
Encryption Method
By default, all data exchanges on your wireless network are not

encrypted, but you can select an encryption method in this
option, and use the extra workspace features that appear to
fine-tune the encryption settings.
Ruckus Wireless strongly recommends using WPA as the
encryption method as WEP is easily circumvented.
For more information, refer to either Using WEP on page 135
or Using WPA on page 137.
134
Configuring the AP
4 When you are finished, click Update Settings to save and apply the changes.
A confirmation message appears at the top of this page.
5 Click Go back to Wireless Configuration to reopen the previous page.
If required, continue with the following:
Using WEP
Using WPA
Customizing 802.1X Settings
Setting Threshold Options
Rate Limiting
Controlling Access to the Wireless Network
Using WEP
Wired Equivalent Privacy (WEP) is a security algorithm for 802.11 wireless networks
designed to provide data confidentiality comparable to that of a wired network. WEP
uses a pre-shared key for encrypting data frames that is shared among all users of
the wireless network. For this reason and others, WEP has been discredited as a
security mechanism and should be avoided in favor of WPA if at all possible.
CAUTION! WEP encryption is easily circumvented. Therefore, Ruckus Wireless
recommends using WPA whenever possible, and only use WEP if your client devices
do not support WPA.
CAUTION! Using WEP encryption limits the performance of the WLAN to 802.11g
rates. If you select WEP encryption for a WLAN, wireless devices that are capable
of faster 802.11n transfer rates are limited to 802.11g rates. Other WLANs are
unaffected.
1 Go to Configuration > Wireless or Configuration > Radio 2.4G or
Configuration > Radio 5G. The Configuration > Wireless > Common page
appears.
2 Click the Wireless # (WLAN number) tab that you want to configure. The
Configuration > Wireless > Wireless[#] page appears.
3 Select WEP from the Encryption Method menu. An additional set of WEPspecific encryption options appear on this page.
135
Configuring the AP
Figure 63. WEP settings
4 Review the encryption settings listed in Table 47, and then make changes as
required.
Table 47. WEP Options
Encryption Setting
Description
Authentication Mode
Open is the only authentication mode available with WEP

encryption.
Encryption Strength
64 bit: Specify the key with 10 hexadecimal digits or 5 ASCII

characters.
128 bit: Specify the key with 26 hexadecimal digits or 13
ASCII characters. The 128-bit cryptography is stronger
privacy protection for your network and is recommended if
you use WEP.
Key Entry Method
Hexadecimal: The encryption key only accepts

hexadecimal characters (0-9, A-F).
ASCII Text: The encryption key accepts ASCII characters.
WEP Key
Enter the key manually according to the Key Entry Method

and Encryption Strength settings.
Key Index
Choose the index, from 1 to 4, that the WEP key is to be

stored in.
136
Configuring the AP
5 Click Update Settings to save and apply the changes. A confirmation message
appears at the top of the page.
Using WPA
Wi-Fi Protected Access (WPA) and Wi-Fi Protected Access II (WPA2) are two
security protocols developed by the Wi-Fi Alliance in response to the weaknesses
of WEP.
Selecting WPA as the Encryption Method allows you to choose WPA version, WPA
Authentication and WPA Algorithm. This section discusses WPA-PSK (pre-shared
key). For information on WPA-Enterprise (WPA-802.1X), refer to Customizing
802.1X Settings on page 139.
Use of WPA-PSK (also known as WPA-Personal) allows automatic key generation
based on a single passphrase. WPA-PSK provides strong security for small and
medium organizations and does not require a RADIUS server, but may not be
supported on older wireless devices. In some cases, the older devices can be
upgraded with adapters to take advantage of WPA-PSK.
If you configure the WLAN with WPA-PSK, wireless users are not able to connect
to your WLAN unless their devices support WPA-PSK and are configured with the
same passphrase.
appears.
2 Click the Wireless # tab that you want to configure. The Configuration > Wireless
> Wireless[#] page appears.
3 Select WPA from the Encryption Method menu. An additional set of WPAspecific options appear on this page.
137
Configuring the AP
Figure 64. WPA settings
4 Review the encryption settings listed in Table 48, and then make changes as
preferred.
Table 48. Encryption settings
Encryption Setting
Description
WPA Version
Your options are WPA, WPA2 or WPA Auto.

WPA (Wi-Fi Protected Access) is the replacement security
standard adopted by the Wi-Fi Alliance in response to the
security weaknesses of WEP. WPA was developed as an
interim measure before ratification of the 802.11i standard,
which introduced WPA2.
WPA2 provides stronger wireless security than WPA and is
the recommended option. However, older wireless clients
may not be compatible with WPA2. For example, WPA2
support on Windows XP requires a Microsoft patch and is
only available on Windows XP with Service pack 2 or later.
WPA-Auto allows both WPA and WPA2 devices to operate
on the same WLAN.
138
Configuring the AP
Table 48. Encryption settings (Continued)

WPA Authentication
PSK (Pre-Shared Key) mode is suitable for home or office use.

802.1X mode uses a RADIUS server to verify user identity.
The WPA-Auto mode offers both options for the wireless
client to choose from.
For more information on how to configure 802.1X
authentication, refer to Customizing 802.1X Settings on
page 139.
WPA Algorithm
TKIP: Temporal Key Integrity Protocol is an older encryption

algorithm that provides stronger security than a shared
WEP key, but not as strong as the newer AES algorithm.
AES: AES (Advanced Encryption Standard) replaces TKIP
as the default (and recommended) encryption algorithm for
modern wireless LANs.
Auto: Auto allows both encryption algorithms to be used
on the same WLAN. When Auto is selected, the wireless
client decides whether TKIP or AES is used. Note however
that allowing TKIP reduces the performance of the WLAN
(as broadcast packets are limited to slower transfer rates),
and is therefore not recommended.
Passphrase
Enter a new passphrase between 8 and 32 characters, using

any combination of printable characters (letters, numbers,
hyphens and underscores).
Customizing 802.1X Settings

CAUTION! Do not customize these options unless you are an experienced network
administrator or are under the guidance of an IT/support professional.
If you choose WPA as the encryption method, you have the option to set up the AP
to act as an 802.1X proxy, utilizing external authentication sources such as a
RADIUS server.
139
Configuring the AP
In 802.1X authentication, the supplicant sends access request messages along with
credentials, such as user name / password or digital certificate, to an authenticator,
which forwards the credentials to the authentication server for verification. The
supplicant (client device) remains in an unauthorized state until verification has been
received. In unauthorized state, only 802.1X traffic is allowed; all other traffic, such
as DHCP and HTTP traffic, is dropped. For its wireless interfaces, the AP can serve
as the authenticator communicating between the supplicant and the authentication
server.
appears.
2 Click a Wireless # (WLAN number) tab to configure. The Configuration >
Wireless > Wireless[#] page appears.
3 From the Encryption Method menu, select WPA. The basic set of WPA-specific
encryption options appears on the page.
4 Select 802.1X as the WPA Authentication mode. Additional options appear.
Figure 65. 802.1X settings
5 Configure the following settings to customize your 802.1X authentication:

RADIUS NAS-ID: Enter the Network ID assigned to your AP in the RADIUS
server Client list.
Authentication Server: Enter the information needed to establish a connection between the AP and the RADIUS server.
140
Configuring the AP
Accounting Server: Optionally, enter the information needed to establish

this connection.
appears at the top of this page.
NOTE Ruckus Wireless APs do not support arbitrary rate values for 802.1X clients
(if client rate limiting attributes are configured on the RADIUS server). Ruckus
Wireless APs support only those WLAN rate limiting values that can be set using
the AP web interface. If the rate returned by the RADIUS server does not match one
of these values exactly, it is approximated.
Setting Threshold Options

The following options allow you to fine-tune the Protection Mode behavior, set
previously on the Configuration > Wireless > Advanced > Common page. After
activating a Protection Mode, you can open each Wireless tab and customize the
threshold settings, which determine what is put into effect and when.
CAUTION! Do not customize these options unless you are an experienced network
administrator or are under the guidance of an IT/support professional.
appears.
2 Click the tab for the Wireless # (WLAN number) that you want to configure. The
Configuration > Wireless > Wireless [#] page appears.
3 Look for Threshold Settings, and then click Edit Settings. The Configuration >
Wireless > Advanced > Wireless [#] page appears.
141
Configuring the AP
Figure 66. Threshold settings
4 Review the options listed in Table 49, and then make any needed changes.
Table 49. Threshold options
Option
Description
Beacon Interval
(The default value is 100.) The value indicates the frequency

interval of the beacon in milliseconds. A beacon is a broadcast
packet sent by the AP to synchronize the wireless network.
Data Beacon Rate

(DTIM)
(The default value is 1.) The value indicates the interval of the
Delivery Traffic Indication Message (DTIM). This is a
countdown field that the device uses to inform its clients of
the next window for listening to broadcast or multicast
messages.
RTS/CTS Threshold
(The default value is 65535.) This option determines at what

packet length the RTS/CTS function is triggered. A lower
threshold may be necessary in an environment with excessive
signal noise or hidden nodes, but may result in some
performance degradation.
You have completed configuring the threshold options. To reopen the previous page,
click the Go back to Wireless Configuration link.
142
Configuring the AP
Rate Limiting
Rate Limiting allows you to cap the per client data transfer rates for a specific WLAN.
Configuration > Radio 5G.
2 Select the WLAN number that you want to configure from the tabs at the top of
the page.
3 Click the Edit Settings button next to Rate Limiting. The Rate Limiting page
appears.
Figure 67. Limit per station traffic rates on a specific WLAN
4 Set the maximum Downlink and Uplink rate per station.

5 The table under the Downlink and Uplink selections updates to show the
maximum transfer rate per station for each traffic type.
143
Configuring the AP
Controlling Access to the Wireless Network

Access Control enables you to specify the stations are allowed to join (associate
with) your wireless networks. Access controls can be configured for each WLAN
from its respective Wireless # tab.
Access Control Options

This section describes the options that you can use to control access to the wireless
network.
Disabling WLAN Access Restrictions: If you select Disable WLAN access
restrictions, then MAC-address-based restrictions on which stations can join
the WLAN are disabled; thus, any station can join. If the WLAN uses encryption,
then the station must still supply the correct encryption passphrase. The Access
Controls table is hidden if the current mode is Disable WLAN access restrictions.
Allowing Only Stations Listed in the Access Controls Table: If you select Allow
only stations listed in the Access Controls Table, then stations entered into
the access-controls table are allowed but all others are disallowed. To add MAC
addresses, refer to Changing the Access Controls for a WLAN on page 144.
Denying Only Stations Listed in the Access Controls Table: If you select Deny
only stations listed in the Access Controls Table, then stations entered into
the access-controls table are disallowed but all others are allowed. To add MAC
addresses, refer to Changing the Access Controls for a WLAN on page 144.
Changing the Access Controls for a WLAN

By default, the Disable WLAN access restrictions option is selected, which allows
any wireless station to gain access to the wireless network. If you want to change
this setting, follow the instructions below.
Configuration > Radio 5G.
2 Click the Wireless # tab for which you want to configure the access control
settings.
3 Click the Edit Settings button next to Access Control. The Access Control page
appears.
144
Configuring the AP
4 Click Allow only stations listed in the Access Controls Table or Deny only
stations listed in the Access Controls Table. (For a description of the options,
refer to Access Control Options in the previous section.)
The Access Control Table appears.
Figure 68. Access control settings
5 To add a MAC address to the Access Control table, click Add new entry.
6 Fill out the following text boxes:
Address: Six text boxes appear in which you enter the desired MAC address,
in hexadecimal digit form, two characters in each box. Allowable hex-digit
characters are 0-9, a-f, and A-F.
7 Click Update to save your changes. Assuming all parameters you entered are
acceptable, that row is added to the table.
You have completed adding an entry to the MAC address table. If you have additional
MAC addresses you want included, click Add new entry, and then repeat these
steps until you have entered all the stations you want. There is a limit of 128 rows.
Removing a MAC Address

To remove a MAC address from the ACL table, click the Cancel button under the
Remove column, and then click Update. The ACL table refreshes, and the MAC
address that you deleted disappears from the table.
145
Configuring the AP

The Ethernet Ports configuration page allows you to define how the APs Ethernet
ports behave. You can disable ports entirely, define trunking and packet forwarding
behavior, configure 802.1X authentication settings, and configure VLAN settings for
each port individually from this page.
1 Go to Configuration > Ethernet Ports.
Figure 69. The Configuration > Ethernet Ports page
2 Review Table 50 and make changes as needed for each of the ports labeled
Port1 through Port4 (depending on AP model), which correspond to the APs
Ethernet ports.
Table 50. Configuring Ethernet ports
Setting
Description
Enable
All Ethernet ports are enabled by default. Unchecking this

box next to a port disables that port entirely. If you do not
want to provide wired access through the AP, uncheck
(clear) the Enable box next to each LAN port.
146
Configuring the AP
Table 50. Configuring Ethernet ports (Continued)

Port Type
See Setting Ethernet Port Type on page 149 for more

detailed information.
Trunk port: This port passes all VLAN traffic.
Access Port: This port provides network access.
General Port: User-defined VLAN membership.
Packet Forward
Isolated: Selecting Isolated causes the traffic from this port

to terminate at the AP.
Bridge to WAN: The default setting, Bridge to WAN
forwards packets arriving on this port to the WAN (uplink)
port and eventually to their external destinations using Layer
2 forwarding.
Local Subnet NAT and Route to WAN: This setting
allows routing of packets to their destinations using Layer 3
network address translation (NAT).
Bridge to L2TP Tunnel: Uses Layer 2 Tunneling Protocol
to deliver packets encapsulated with an L2TP header in UDP
datagrams.
Local Subnet
This option appears if you have selected Local Subnet and

Route to WAN under Packet Forwarding, and you have
selected Access Port as the port type. This option allows
you to select which subnet this ports traffic is part of. You
must have previously configured a subnet from the
Configuration > Local Subnets page before it becomes
available here.
147
Configuring the AP
Table 50. Configuring Ethernet ports (Continued)

802.1X
Configure the port as an 802.1X authenticator or supplicant.

The following options are available:
Disabled: No 802.1X controls are applied to this port.
Authenticator (Port-based): Only one of the attached
MAC hosts must be authorized for all hosts to be granted
access to the network.
Authenticator (MAC-based): Each MAC host is
individually authenticated.
Supplicant: The port acts as a supplicant to an
upstream authenticator. Configure a port as Supplicant if
the port is a Trunk Port used to connect the AP to a LAN
switch.
See Working with 802.1X on Wired Ethernet Ports on
page 150 for more information.
VLAN
Untag ID: Enter a valid VLAN ID in this field to segment

traffic arriving on this port to a specific VLAN. Default is 1.
Valid VLAN entries are 1-4094.
Members: Displays the VLAN membership of the port.
(Membership is configurable only for the General port type.)
Refer to Working with Port-Based VLANs on page 150
for more information.
Insert DHCP Option 82
When this option is enabled for an Ethernet port, additional

information is encapsulated in DHCP option 82 and inserted
into DHCP request packets.
Current format of option 82 is:
Circuit ID sub-option:
ETH:<IFNAME>:<VLAN>:N/A:
<MODEL>:<HOSTNAME>:<DEVMAC>
This option supports the ability for a service provider to
allocate IP addresses intelligently by considering information
on the origin of the IP allocation request.
Client Fingerprinting
When this option is Enabled, the AP attempts to identify

client devices by their operating system, device type and
host name, if available.
148
Configuring the AP
Refer to the following, as required:

Setting Ethernet Port Type
Working with Port-Based VLANs
Working with 802.1X on Wired Ethernet Ports
Setting Ethernet Port Type

Ruckus Wireless AP Ethernet ports can be configured as one of the following port
types:
Trunk Port
Access Port
General Port
Trunk Port
Trunk Ports forward and receive tagged and untagged frames and are used for
bridging switch ports together. The Trunk port is a member of all VLANs that exist
on the switch, and all VLAN-tagged traffic arriving on the port is seen. If an untagged
frame is received on a Trunk port, the frame is associated with the Untag VLAN (also
known as native VLAN, by default, 1).
If a port is configured as a Trunk port, the Untag ID field can be used to define the
Untag VLAN--the VLAN that the switch uses for forwarding/filtering purposes when
a frame arrives without an 802.1Q header.
Access Port
Access Ports are used to provide network access. Traffic arriving on different Access
Ports can be segmented into different logical networks (VLANs) using the Untag
VLAN ID field. Access Ports are members of only one VLAN--the VLAN that is
configured in the Untag VLAN field.
General Port
The General Port can be configured to support multiple tagged VLANs and one
untagged VLAN. As Trunk Ports by definition are members of all VLANs, the General
Port is the only port type for which membership is user configurable for multiple
VLANs.
149
Configuring the AP
Working with Port-Based VLANs

The AP provides options for segmenting all incoming traffic (both wireless and wired
Ethernet traffic) into specific VLANs. There are two ways to segment incoming traffic
into VLANs:
Each of the wireless interfaces (SSIDs) can be configured with a specific Access
VLAN ID: (Configuration > Wireless > Wireless [#] > Access VLAN).
Each of the LAN ports can be configured with an Untag VLAN ID (Configuration
> Ethernet Ports > VLAN > Untag ID).
For Ethernet ports, the behavior of the Untag VLAN ID depends on the Port Type
selected. If the port is configured as a Trunk port, it includes all VLANs (1-4094) in
its membership. The VLAN Untag ID field (default = 1) can be used to redefine the
Native VLAN for the port.
If the Ethernet port is configured as an Access Port, it can be configured with only
one Untag VLAN ID and its membership includes only that one VLAN.
If the Ethernet port is configured as a General Port, it can be configured to include
multiple VLANs in its membership and one Untag VLAN.
Working with 802.1X on Wired Ethernet Ports

802.1X authentication consists of the following three components:
Supplicant: The supplicant sends access request messages along with credentials, such as user name / password or digital certificate, to an authenticator,
which forwards the credentials to the authentication server for verification.
Authenticator: The authenticator challenges the identity of the supplicant, then
passes its credentials to the AAA server. If the credentials are accepted the
supplicant is allowed access.
Authentication Server (AAA Server): The AAA server verifies the supplicants
credentials and permits or rejects its request for access.
For wired 802.1X, a Ruckus APs Ethernet port can be configured as either an
Authenticator or as a Supplicant, depending on which port type is selected. Table
51 and Table 52 describe the 802.1X roles available by port type.
150
Configuring the AP
Table 51. Authenticator support by port type
Port-based mode
Trunk Port
Access Port
General Port
MAC-based mode
Table 52. Supplicant support by port type

Trunk Port
Supplicant
Access Port
General Port
The following considerations apply:

A single port cannot be configured as both an Authenticator and Supplicant at
the same time.
Only one port per AP can be configured as a Supplicant.
If the AP is connecting to a switch port with 802.1X authentication enabled, the
APs port type should be configured as a Trunk Port and its role should be
configured as Supplicant. The switch port should be configured as a Trunk port
in Port-based Authenticator mode.
If there are multiple devices connected to an AP port (through a downstream
switch), the port can be configured as either Port-based or MAC-based Authenticator. In Port-based mode, only one of the attached MAC hosts must be
authorized for all hosts to be granted access to the network. In MAC-based
mode, each MAC host is individually authenticated.
If a Trunk Port is configured as a Supplicant, a user name and password must
be entered to authenticate the port to the 802.1X aware LAN switch.
If an Access Port is configured as an Authenticator, the administrator must define
the RADIUS server that the Authenticator communicates with. All Ethernet ports
of a single AP are configured with the same RADIUS server.
Enable MAC authentication bypass: If MAC authentication bypass is enabled, the
port first attempts to authenticate the attached device by MAC address, and if that
fails, it attempts to authenticate the device using 802.1X.
151
Configuring the AP

Hotspot service can be deployed on standalone APs through the Web interface. At
a minimum, you must configure a login redirect URL and a RADIUS server to which
users are authenticated. Additional options and controls are provided on subsequent pages.
1 Go to Configuration > Hotspot.
Figure 70. Minimum configuration settings for providing Hotspot service
2 Click Enabled next to Hotspot Service.

3 Review the settings in table Table 53, and make changes as needed.
Table 53. Hotspot configuration settings
Setting
Description
Redirect unauth. user to
Redirect unauthenticated users to the specified URL (login

page).
152
Configuring the AP
Table 53. Hotspot configuration settings (Continued)

Setting
Description
After user is authenticated Select where you want to redirect the user after successful
authentication.
Redirect to the above URL: return to the login URL
configured above.
Redirect to the URL the user intended to visit: upon
successful authentication, go directly to the URL that
the user originally entered (typically the browsers home
page).
Redirect to: specify a URL to which users are redirected
after authentication. This can be used to redirect users
to a Login Successful page, or a page that offers
connection time information or a Logout button.
Primary RADIUS Server
Enter the IP address of the primary RADIUS server against

which users are authenticated (required).
Secondary RADIUS Server Enter the IP address of the secondary RADIUS server, if
one is available (optional).
RADIUS Server Secret
Enter the shared secret for communication with the

RADIUS server (required).

You have completed the minimum settings for providing Hotspot service on this AP.
Additional configuration options are available using the Edit Settings buttons on
the page:
Customizing Hotspot Optional Settings
Creating a Hotspot Walled Garden
Allowing Unrestricted Access by MAC Address
153
Configuring the AP
Customizing Hotspot Optional Settings

Optional Hotspot settings include a number of options for fine-tuning your Hotspot
service, such as maximum session time, grace period, accounting update interval,
etc.
2 Click the Edit Settings button next to More Options. The More Options page
appears.
Figure 71. Configuring optional Hotspot options
The Table 54 Hotspot options can be configured from the Configuration > Hotspot
> More Options page:
Table 54. Optional Hotspot settings
Setting
Description
Temporarily block user after

__ unsuccessful login
attempts
Specify the maximum number of repeated

authentication failures allowed.
Redirect temp. blocked user Enter a redirect URL to which blocked users are
to
redirected.
154
Configuring the AP
Table 54. Optional Hotspot settings (Continued)

MAC Authentication
If enabled, the Hotspot service attempts to authenticate

users based on their MAC addresses if the local Hotspot
authentication has failed. If enabled, an optional MAC
authentication password can be entered. If no password
is specified, the system uses the clients MAC address
as the password.
Acct Delay Time
This attribute indicates how many seconds the client has

been trying to send this record for, and can be subtracted
from the time of arrival on the server to find the
approximate time of the event generating this
Accounting-Request. When enabled, this attribute
appears in accounting request packets with a starting
value of 0, incremented each retry packet. When
disabled, this attribute is not included in any accounting
request packet.
NAS ID
Specify the Network Access Server identifier of this

device. The NAS-ID attribute is sent in RADIUS access
and accounting request messages. It can also be used
as location identification when NAS-IP-Address cannot
be used for this purpose.
WISPr Location ID
Specify the Hotspot location identifier. This value is

provided in the RADIUS access and accounting
requests. It is recommended that the value is in the form
of isocc=<ISO_Country_Code>,
cc=<E.164_Country_Code>,ac=<E.164_Are
a_Code>,network=<SSID/ZONE>.
WISPr Location Name
Specify the hotspot location and operator's name. This

value is provided in the RADIUS access and accounting
requests. It is recommended that the value is in the form
of <HOTSPOT_OPERATOR_NAME>,<Location>.
Location Description
Specify the description of location. This value is provided

in the HTTP redirection.
Accounting Update Interval
Specify the interval for RADIUS accounting requests.
Interim Redirect Interval
Specify the interval after which users are redirected to

the login URL.
Maximum Session Time
Enter the maximum session time in minutes.
155
Configuring the AP
Table 54. Optional Hotspot settings (Continued)

Grace Period
Specify the maximum time that a user may disconnect

from the Hotspot service and return without the need to
login again.
RADIUS Disconnect Port
UDP port to listen to for accepting RADIUS disconnect

requests.
Swap Input and Output

Counters
Swap the value of input counters (packets, octets and

giga words) and output counters in RADIUS accounting
requests. This option is mainly for backward
compatibility with existing ChilliSpot deployments.
Encode User Password
Encode user password with challenge string, if UAM

secret is not specified; otherwise, encode user
password with both challenge string and UAM secret.
UAM Shared Secret
The UAM Shared Secret is the shared secret between

this AP and the HTTP server for the Redirection URL.
This setting is optional.
156
Configuring the AP
Creating a Hotspot Walled Garden

You can use the Hotspot Walled Garden rules to designate network destinations
(host address or subnet) that users can access without going through authentication. A Walled Garden is a limited environment to which an unauthenticated user is
given access for the purpose of setting up an account. After the account is
established, the user is allowed out of the Walled Garden. URLs are resolved to an
IP address (up to four). Users will not be able to click through to other URLs that
may be presented on a page if that page is hosted on a server with a different IP
address. Avoid using common URLs that are translated into many IP addresses
(such as www.yahoo.com), as users may be redirected to reauthenticate when they
navigate through the page.
Creating Walled Garden Rules
Removing entries from the Walled Garden hosts table
Creating Walled Garden Rules

2 Click the Edit Settings button next to Walled Garden. The Walled Garden page
appears.
Figure 72. The Walled Garden hosts table
157
Configuring the AP
3 Click Add new entry. A field entitled Walled Garden Host appears.
4 In Walled Garden Host, enter a host name, IP address, network segment (e.g.,
192.168.1.0/24) or a domain name. If a domain name is entered, it is resolved
every 5 minutes.
5 Click Update to save your entry.
You can create up to 64 entries in the Walled Garden Hosts table.
Removing entries from the Walled Garden hosts table

1 Click the check box next to the entry you want to remove, under the Remove?
column.
2 Click Update. The entry is removed from the list.
Allowing Unrestricted Access by MAC Address

2 Click the Edit Settings button next to Unrestricted Clients. The Unrestricted
Clients page appears.
Figure 73. Configuring Hotspot unrestricted clients table
3 Click Add new entry, and enter the MAC address of each client in the fields
provided.
4 Click Update to save your changes.
158
Managing the AP
In this chapter:
Viewing Current Device Settings
Viewing Current Internet Connection Settings
Viewing Current Local Subnet Settings
Viewing Common Wireless Settings
Changing the Administrative Login Settings
Enabling Other Management Access Options
Working with Event Logs and Syslog Servers
Upgrading the Firmware Image
Rebooting the AP
Resetting the AP to Factory Defaults
Running Diagnostics
Where to Find More Information
This chapter provides instructions for managing standalone Ruckus Wireless APs
using the AP Web interface. For information on managing your Ruckus Wireless
network using SmartCell Gateway (SCG), SmartZone (SZ), virtual SmartZone (vSZ),
ZoneDirector (ZD), Smart Access Management service (SAMs), or FlexMaster (FM),
refer to the relevant User Guide, available from the Ruckus Wireless Support
website.
159
Managing the AP

The Status > Device page displays a general overview of the APs current status,
including device name, serial number, MAC address, current software version, and
so on.
Figure 74. The Status > Device page
160
Managing the AP

The Status > Internet page displays information on the APs network settings; i.e.,
the settings that allow the AP to communicate with your local network and the
Internet. Information includes IP address, gateway, DNS server, NTP server and
connection type (method of obtaining an IP address -- DHCP or static IP).
Figure 75. The Status > Internet page
161
Managing the AP

The Status > Local Subnets page can be used to view the router (local subnet)
configurations and list of any clients connected to those subnets.
If you want to make changes to any of these settings, go to Configuration > Local
Subnet. Refer to Configuring Local Subnets for more information.
Figure 76. The Status > Local Subnet page
162
Managing the AP

If you want to view the current common wireless settings that the AP is using, go
to the Status > Wireless page (on dual-band APs, go to Status > 2.4G or Status
> 5G). Table 55 lists the descriptions of each common wireless setting.
Figure 77. The Status > Wireless (Radio 2.4G/5G) > Common page
Table 55. Common Wireless settings

Setting
Description
Wireless Mode
Shows the wireless mode that the AP is currently using.

Possible values include:
Auto Select: (For 802.11b/g APs only) Allows both
802.11g- and 802.11b-compliant devices to connect
to the network. This is the default setting.
2.4GHz 54 Mbps: Allows 11g devices only.
2.4GHz 11 Mbps: Allows 11b devices only.
11ng: Operates with 802.11n, 802.11g and 802.11b
devices in the 2.4Ghz spectrum only.
11na: Operates with 802.11n and 802.11a devices in
the 5GHz spectrum only.
163
Managing the AP

Channel
Shows the wireless channel that the AP is currently using.

If you set the wireless channel to SmartSelect, this field
shows the value Channel # [SmartSelect].
Channel Width
11n devices only. Displays whether the channel width is

set to 20MHz or 40MHz.
Country Code
Shows the country code that the AP has been set to use.
CAUTION! Verify that the AP is using the correct
country code to make sure it uses only the allowed

radio channels in your region. Selecting the incorrect
country code may result in violation of applicable laws.
AeroScout RFID tag
detection (some APs)
Shows Enabled if you enabled AeroScout RFID tag

detection. The default setting is Disabled.
AeroScout Engine
communication daemon
(some APs)
Shows Up if the communication agent on the AP is able

to relay location data from AeroScout Tags to the
AeroScout Engine.
If the communication agent is unable to relay data or
AeroScout tag detection is disabled, this field shows
Down.
Ekahau Engine
communication daemon
(some APs)
Shows Enabled if you have enabled Ekahau RFID tag

detection. Default is disabled.
ERC IP (some APs)
Ekahau Real Time Location System RTLS Controller IP

address.
ERC Port (some APs)
TCP port used by the Ekahau Real Time Location

System RTLS Controller.
If you want to make changes to any of these settings, go to the Configuration >
Wireless page. Refer to Configuring Common Wireless Settings for more information.
164
Managing the AP
Viewing Associated Wireless Clients
Viewing Associated Wireless Clients

A usage-monitoring capability has been built into the AP to help you monitor wireless
clients that are associated with your wireless network.
1 Go to Status > Wireless. The Status > Wireless page appears.
NOTE If you are using a dual-band AP, then go to Status > Radio 2.4G or Status
> Radio 5G.
2 Click any of the Wireless # tabs. Wireless clients that are associated with this
particular wireless network appear under Connected Devices.
Figure 78. Viewing connected devices
165
Managing the AP

The default user name is super and the default password is sp-admin. To prevent
unauthorized users from logging in to the Web interface using these default
administrator login settings, Ruckus Wireless recommends that you change the
default Web interface password immediately after your first login.
1 Log into the Web interface.
2 Go to Configuration > Device.
Figure 79. The Configuration > Device page
3 Under Service Provider Login, change the default administrator login settings.
In Username, type a new user name to log in to the Web interface. The default
user name is super.
In Current Password, enter the existing password.
In New Password, type a new password to replace the default password spadmin. The password must consist of six to 32 alphanumeric characters
only.
In Confirm New Password, retype the new password.
4 Click Update Settings. The message Your parameters were saved appears.
You have completed changing the default login settings. The next time you log in to
the Web interface, make sure you use these updated login settings.
166
Managing the AP

In addition to managing the AP via a Web browser through HTTPS, several other
management access options are available on the AP. These options include
management access via HTTP, Telnet, and SSH.
You can also view and set up the connection to a Ruckus Wireless FlexMaster server
under the TR-069/SNMP Management Choice options. If your Ruckus Wireless
device is to be managed by FlexMaster, then the FlexMaster information (server URL
and contact interval) is preconfigured before you receive your Ruckus wireless
device.
NOTE If you are configuring the AP to be managed by FlexMaster, remember to
point it to the FlexMaster server after you configure the management access options.
For more information, refer to Viewing FlexMaster Management Status on
page 171.
1 Go to Administration > Management. The Management page appears.
Figure 80. The Administration > Management page
2 Review the access options listed in Table 56, and then make changes as needed.
Table 56. Management Access Options
Option
Description
Telnet Access
By default, this option is disabled (inactive).
167
Managing the AP
Table 56. Management Access Options (Continued)

Option
Description
Telnet Port
This field lists the default Telnet port of 23 only if Telnet is active.
You can manually change this port number, if required.
SSH Access
By default, this option is enabled (active).
SSH Port
This field lists the default SSH port of 22only if SSH is active. You
can manually change this port number if required.
HTTP Access
This option is disabled by default.
HTTP Port
This field lists the default HTTP port of 80, if HTTP has been
activated. You can manually change this port number if required.
HTTPS Access
By default this option is enabled. This connection mode requires a

security certificate, a copy of which has been pre-installed in the
device.
HTTPS Port
This field lists the default HTTPS port of 443only if HTTPS has
been activated. You can manually change this port number if
required.
Certification
Verification
This notes whether the security certificate linked to the HTTPS

settings has been passed or not.
Controller
Discovery Agent
(LWAPP)
Enabled (default) -- Lightweight Access Point Protocol controller

discovery on. (Refer to Release Notes for details.)
Cloud Discovery
Agent (FQDN)
Enabled (default) -- Fully Qualified Domain Name cloud discovery

on; requires enabled LWAPP controller discovery Enabled. (Refer
to Release Notes for details.)
Disabled -- LWAPP controller discovery off.
Disabled -- FQDN cloud discovery off.

Set Controller
Address
Enabled -- The AP uses an IP address to search for the primary

and/or secondary SCG, SZ, vSZ or ZD controller. When Set
Controller Address is Enabled, enter the required primary
controller IP address and the optional secondary controller IP
address.
Disabled (default) -- The AP does not use IP address(es) to search
for SCG, SZ, vSZ or ZD controllers.
168
Managing the AP
Table 56. Management Access Options (Continued)

Option
Description
PoE Operating
AUTO = allow the AP to decide if it is to operate off of 802.3at or
Mode (some APs) 802.3af power over Ethernet, or 802.3af PoE = force the AP to
operate off of 802.3af power over Ethernet. Default = AUTO.
Note: As described in ZoneFlex R710 AP section, the R710 AP
can operate off of 802.3af power, but the feature set is reduced.
Primary and
Controller Addr
Refer to Set Controller Address/Enabled above.
3 If you want to use TR-069 or SNMP to manage the AP, then configure the settings
listed in Table 57.
Table 57. TR-069 and SNMP Management Options
Option
Description
Auto
Enables the Ruckus Wireless device to be managed by

either SNMP server, Ruckus Wireless ZoneDirector, or
Ruckus Wireless FlexMaster.
SNMP only
Only allow SNMP management.
FlexMaster only
Only allow FlexMaster management.
DHCP Discovery
URL of server providing DHCP.
FlexMaster Server URL
URL of the FlexMaster server.
Digest-authentication
Username/Digestauthentication password
This information is automatically generated by the AP and

used for authentication with FlexMaster. Change this value
only if you want the AP to connect to another access
control server (ACS).
Periodic FlexMaster Inform Interval at which the device should attempt to contact
Interval
FlexMaster. Default = 15 minutes.
4 Click Update Settings to save your changes. A confirmation message appears

at the top of the page.
You have completed configuring the management access options.
169
Managing the AP
NOTE Remember to open any relevant firewall ports between the AP and the
firmware upgrade/management server. For example, if HTTPS is used for firmware
upgrades, open TCP port 443 on the firewall to allow connections through port 443.
If FlexMaster server is used, open TCP ports 80 and 443 for HTTP/HTTPS
communications, and TCP port 8082 for AP wake-up commands.
Continue with the following, as required:
Viewing FlexMaster Management Status
Pointing the AP to FlexMaster
170
Managing the AP
Viewing FlexMaster Management Status

If you configure the AP to be managed by FlexMaster, you can view the TR-069
Status section on the Administration > Management page.
Figure 81. TR-069 status information
Table 58 lists the TR-069 status information that the AP provides.

Table 58. TR-069 status information
Status Information
Description
Currently Using URL
Shows the FlexMaster server IP address or URL with

which the AP is currently registered.
Last Attempted Contact
Shows the date and time of the APs last attempt to

contact FlexMaster. Date and time are specified in GMT
(or UTC), which are accurate if a Network Time Protocol
(NTP) server is configured.
Last Successful Contact
Shows the date and time of the APs last successful

contact with FlexMaster.
Last Contact Result
Shows the result of the last attempt to contact FlexMaster

(success or failure, and failure error code if applicable).
171
Managing the AP
Table 58. TR-069 status information (Continued)

Status Information
Description
Current Time
Shows the current date and time as known to the AP. This
timestamp is accurate if an NTP server is configured on
the AP. If there is no NTP server configured, this timestamp
is useful as a reference for comparison of the timestamps
for Last attempted contact and Last successful
contact.
Pointing the AP to FlexMaster

Your Ruckus Wireless device is required to call home to register with your
FlexMaster; FlexMaster does not initiate initial contact. To register successfully with
FlexMaster, your Ruckus Wireless device must know the FlexMaster servers URL,
thus entered on the device. You need TCP ports 80 and 443 between APs and
FlexMaster when traversing Layer 3/firewall boundaries.
1 Go to Administration > Management.
2 Under TR-069/SNMP Management Choice, click Auto.
3 In FlexMaster Server URL, type the URL of the FlexMaster server.
4 Toggle the Periodic FlexMaster Inform Interval drop-down list to select how
frequently the device checks the FlexMaster server for any pending configuration
changes available for that Ruckus Wireless unit. On the FlexMaster side, this
field is referred to as the Periodic Inform Interval.
After the AP registers with FlexMaster, this Administration > Management page will
show the communication status between the AP and FlexMaster.
172
Managing the AP

Both the Maintenance > Support Info and Administration > Log pages can be used
to view the APs current log file text. You can use the former to send the log to
Ruckus Wireless support directly or save it to a local file, and use the latter to
configure automatic delivery of log files to a syslog server:
Enabling Logging and Sending Event Logs to a Syslog Server
Sending a Copy of the Log File to Ruckus Wireless Support
Sending a Copy of the Log File to Ruckus Wireless Support
Enabling Logging and Sending Event Logs to a Syslog

Server
If you have a syslog server on the network, you can configure the AP to send the
device logs to the server. You need to enable logging (if disabled) and configure the
AP to send logs to the syslog server.
1 Go to Administration > Log. The Administration > Log page appears.
Figure 82. The Administration > Log page
2 Look for Log Status, and then click Enabled.

3 After enabling logging, configure the following options:
Syslog Server Address: To enable the AP to send messages to a syslog server
as they appear, enter the IP address of the syslog server.
173
Managing the AP
Syslog Server Port: By default, the syslog port number is 514. If the syslog
server is using a different port, enter that port number in this field.
4 Click Update Settings to save and apply your changes.
Sending a Copy of the Log File to Ruckus Wireless

Support
The Support Info log consists of the configuration and run-time status of the AP and
can be useful for troubleshooting. You have three options for sending a copy of the
current log file to Ruckus Wireless Support:
Set up a connection to a TFTP site.
Set up a connection to an FTP site.
Save a copy to your local PC, then attach it to an e-mail message and send
it to Support.
1 Go to Maintenance > Support Info. The Maintenance > Support Info page
appears.
2 Review the Transfer Method options.
3 To upload a copy of the support info file to an FTP or TFTP server, click the TFTP
or FTP option. Clicking the FTP option prompts you to enter a Username and
Password.
4 In Server Address, enter the FTP or TFTP server IP address.
5 In Filename, enter a name for this file that you are saving.
NOTE Remember to add a .TXT file extension to the file name, especially if you are
using Internet Explorer as your Web Admin host.
6 Click Upload Now.
Saving a Copy of the Current Log to Your Computer

You can also save a copy of the current log to your own computer, if needed.
1 Go to Maintenance > Support Info. The Maintenance > Support Info page
appears.
2 Review the Transfer Method options.
3 Click the Save to Local Computer option. Two links appear next to Download
(supportinfo.txt and tr069info.txt).
174
Managing the AP
4 Click the supportinfo.txt link. A new window (or tab) opens with the content of
the log file displayed.
5 Choose Save As or Save Page As from your browsers File menu.
6 When the Save as... dialog box appears, find a convenient location on your
local computer to save the file, and change the file extension from .html to .txt.
7 Click Save to save the file to your computer.
175
Managing the AP

You can use the Web interface to check for software updates/upgrades for the
firmware image built into the AP. You can then apply these updates to the device
in one of two ways: manual updating on an as-needed basis, or automating a
regularly scheduled update.
Before starting, decide which option you want to take:
Automate a regularly scheduled update
Run a one-time manual update right now
By default, the automatic upgrade option is disabled.
To upgrade the firmware image, go to Maintenance > Upgrade. When the Upgrade
Method options appear, decide which upgrade method to use. Each of the upgrade
options listed on the Upgrade page are discussed in the succeeding sections.
Figure 83. The Maintenance > Upgrade page

Upgrading Manually via FTP or TFTP
Upgrading Manually via the Web
Upgrading Manually via Local File
Scheduling Automatic Upgrades
176
Managing the AP
Upgrading Manually via FTP or TFTP

1 In the Upgrade Method options, click FTP or TFTP.
2 Click the host name field, and then type the URL of the server. Or click the IP
address field, and then type the IP address of the server. Remember to start the
URL with ftp://.
CAUTION! Do not change any of the Image Control File, Username, or Password
entries.
3 Click Perform Upgrade. A status bar appears during the upgrade process.
4 After the upgrade is completed, you must manually reboot the AP.
Upgrading Manually via the Web

1 In the Upgrade Method options, click Web.
2 If instructed to choose a different URL than the default value, click the Web
Options URL field, and then type the URL of the download Web site. Remember
to start the URL with http://.
4 After the upgrade is completed, you must manually reboot the AP.
Upgrading Manually via Local File

If you have already saved an image file on your local computer, then you can upgrade
directly using the Web interface.
1 In the Upgrade Method options, choose Local.
2 Click the Choose File button and locate the file on your local computer.
3 Select the file and click OK.
5 After the upgrade is completed, the AP must be rebooted.
177
Managing the AP
Scheduling Automatic Upgrades

1 In the Upgrade Method options, click the button for your preferred choice.
2 Enter the required information in the related fields.
CAUTION! Do not change any of the Image Control File, Username or Password
entries.
3 Set the Auto Upgrade option to Enabled.
4 Toggle the Interval to Check for Software Upgrade drop-down list to select your
preferred interval.
5 Choose whether to reboot immediately after upgrading, or schedule the reboot
for a specific time of day using the Schedule Reboot Time After Upgrade list.
Choosing Any Time (the default value) results in the AP performing a reboot
immediately after the automatic upgrade is successful.
6 You have two options at this point:
Click Perform Upgrade, which starts the process and the clock. The next
upgrade occurs at the selected interval.
Click Save parameters only. The clock starts right away, and the actual
upgrade occurs at the first selected interval.
After you click one of these two options, a status bar appears during the upgrade
process.
When the upgrade is complete, the AP automatically reboots at the time you
specified in Step 5.
178
Managing the AP
Rebooting the AP
Rebooting the AP
You can use the Web interface to prompt the AP to reboot, which simply restarts
the AP without changing any of the current settings. Please note that rebooting the
AP disrupts network communications in any currently active WLANs.
1 Go to Maintenance > Reboot/Reset. The Maintenance > Reboot/Reset page
appears.
2 Click Reboot Now. After a brief pause, you are automatically logged out of the
AP.
Figure 84. The Maintenance > Reboot/Reset page
After approximately one minute, you should be able to log back into the AP, which
verifies that the reboot was successful. You can also check the LEDs on the AP to
verify the status of the device.
179
Managing the AP

WARNING! DO NOT reset the AP to factory defaults unless you are directed to do
so by Ruckus Wireless support staff or by a network administrator. Do this only if
you are able to immediately reconnect the restored AP to your computer, to
reconfigure it for Wi-Fi network use as detailed in Installing the AP.
You can use the Web User interface to restore an inoperative AP to its factory default
settings, which completely erases the configuration currently active in the device.
Note, too, that this disrupts all wireless network communications through this
device.
1 Go to Maintenance > Reboot/Reset. The Maintenance > Reboot/Reset page
appears.
2 Click Reset now next to Reset to factory settings.
3 When the confirmation warning appears, read the message and click OK if you
are certain that you want to restore the AP to factory defaults.
After a brief pause, you are automatically logged out of the AP. You must now
disconnect the AP from the switch (and the network) and reconnect it to your
computer, as described in Step 1: Preconfiguring the AP. At this time, you can
restore the network settings, then replace it in your site for full network use.
180
Managing the AP
Running Diagnostics
Running Diagnostics
Two network connection diagnostic tools ping and traceroute have been built
into the AP to help you check network connections from the Web interface.
1 Go to Administration > Diagnostics. The Administration > Diagnostics page
appears. Two options are available:
Ping
Traceroute
2 Click the text field by the option you want to activate, and type the network
address of a site.
3 Click Run Test.
The results appear in the text field below each option.
Figure 85. Pinging a device
181
Managing the AP
Running Diagnostics
Figure 86. Running traceroute on ruckuswireless.com
182
Managing the AP

If you have questions that this User Guide does not address, visit the Ruckus
Wireless Support Portal at https://support.ruckuswireless.com. The Support Portal
hosts the latest versions of user documentation as well as Knowledge Base articles,
software updates and a forum for community discussion of Ruckus Wireless
products.
183
Appendix A: AP Support for

Bluetooth Low Energy Devices
Some Ruckus Wireless APs, such as the H500, support customer-supplied, lowpower (1W or less), Bluetooth Low Energy (BLE) devices, such as BLE beacons.
The BLE devices plug into a USB port on the AP, and the AP can be configured to
turn power to the USB port either on or off.
The Ruckus Wireless APs with USB ports supporting BLE devices can provide
power to the BLE device. The BLE devices perform whatever tasks they are
designed to do without interference from or control (other than supplying USB
power) by the Ruckus Wireless network equipment.
184
Appendix B: Configuring Link

Aggregation (LACP) for AP
Backhaul
The ZoneFlex R710 can use link aggregation control protocol (LACP) as defined in
the 802.1ax (formerly 802.3ad) standard to control the bonding of two 1Gbps
physical Ethernet ports together to form a single 2Gbps logical link.
Link Aggregation and When To Use It

An access point such as the R710 is capable of passing wireless traffic in excess
of 1Gbps. This only occurs in extreme cases, such as during concurrent dual-band
operation over the widest possible channels and highest possible modulation and
coding scheme (MCS) rates in each band, with all traffic flowing in the same
direction. In such cases, a single Gigabit Ethernet backhaul will saturate and limit
the APs capacity to less than 1Gbps.
To alleviate this backhaul limitation, link aggregation can be used to bond multiple
Gigabit Ethernet links into a single, high capacity logical link. The R710s link partner,
typically an Ethernet switch, must also support LACP and be configured to use this
feature.
Wi-Fi client capabilities and data demands should be considered before deploying
LACP for AP backhaul. For the vast majority of enterprise WLANs, single Gigabit
backhaul for APs is more than sufficient.
185
Configuring LACP
LACP is configurable via the AP CLI on R710. The set bond command is used with
the following syntax:
set bond <profile> {options}
+++++++++++++++++++++++++++++++++++++++++++++++++++++
** <profile>: bond0, ...
** options:
- lacp-rate [0,1], 0 for slow, 1 for fast
- xmit-hash [0,1,2], 0 for L(ayer2), 1 for L3+4,
2 for L2+3
- {add|delete} <ethX>
+++++++++++++++++++++++++++++++++++++++++++++++++++++
Profile (profile) bond0 is the only valid profile name.
Options:
LACP rate (lacp-rate) defines the rate at which the AP asks its link partner
(usually the switch) to transmit LACP control packets (LACPDUs). A faster rate
allows the link end-points to respond quicker to any changes on the physical
interface (for instance, failover in case of one of the ports is disconnected) at the
expense of more overhead. The slow (default) rate is adequate for the vast
majority of Enterprise WLAN cases.
Slow (lacp-rate 0) (default) requests link partner to transmit LACPDUs
every 30 seconds.
Fast (lacp-rate 1) requests link partner to transmit LACPDUs every one
second.
Transmit hash (xmit-hash) defines how the AP chooses to distribute packets
between the two physical Ethernet links which comprise the bonded link.
Network topology and expected traffic flows should be considered when
choosing which transmit hash option to use so as to spread traffic as evenly as
possible between the two physical links.
Layer 2 (xmit-hash 0) (default) uses the source & destination MAC
addresses in the packet to determine which physical link the packet is sent
over. This is a fully-compliant 802.3ad option.
186
Layer 3 & Layer 4 (xmit-hash 1) uses source & destination IP addresses as

well as source & destination ports. This policy uses upper layer protocol
information, when available, to generate the hash. This allows packets
destined for a particular network peer to be distributed across both physical
links, although a single connection is limited to one of the physical links.
For fragmented packets, layer 4 information is omitted.
This algorithm is not fully 802.3ad compliant.
Layer 2 & Layer 3 (xmit-hash 2) uses source & destination MAC addresses
as well as source & destination IP addresses. This algorithm places all traffic
to a particular network peer on the same physical link. For non-IP traffic, the
formula is the same as for the layer2 transmit hash policy. This policy is
intended to provide a more balanced distribution of traffic than layer2 alone,
especially in environments where a layer3 gateway device is required to reach
most destinations. This algorithm is 802.3ad compliant.
Add or Delete (add|delete) are used to explicitly define which physical Ethernet
ports (ethx) are part of the bond interface (bond0). At a bare minimum, to enable
LACP on the AP this option must be used to add both physical ports to the bond
interface.
Examples
Enable with defaults:
:set bond bond0 add eth0
Enable and modify LACP rate & distribution algorithm:

:set bond bond0 xmit-hash 1
:set bond bond0 lacp-rate 1
Apply VLANs untag ID to bonded interface:

:set interface bond0 type trunk untag 777
Caveats
As of this writing, the controller and AP Web UIs do not expose LACP settings
or configuration. If an AP is configured via AP CLI to bond its Ethernet ports,
then any per-Ethernet port setting in the Web UIs are ignored by the AP.
187
The R710s 802.3af PoE operating mode, which limits AP functionality so as to

remain within the standard 802.3af PoE power budget, requires that one
Ethernet port be disabled. As such, an AP in 802.3af PoE operating mode cannot
be configured to bond its Ethernet ports with LACP.
NOTE Refer to ZoneFlex R710 AP for a description of the feature and function
limitations imposed under the 802.3af PoE operating mode.
This means LACP is supported as long as the R710 AP is powered via:
802.3at PoE+
Passive PoE injector capable of at least 20W
12V DC power supply
NOTE The switch port must support link layer discovery protocol (LLDP) power
over Ethernet/MDI (PoE+) so the R710 can operate in full-power mode.
188
Index
Numerics
802.11ac AP
H500 47
R500 56
R600 61
R700 66, 70
802.1Q 117
802.1X 139, 148, 150
802.1X settings 139
A
access control 133, 144
Access Port 147, 149
Access VLAN 134
administrative login 166
Advanced Settings
Wireless 128
AeroScout 129, 164
AP
Preconfiguring Firmware 108
Zone 2/Z2 184, 185
associated clients 165
SmartZone (SZ) 12
virtual SmartZone (vSZ) 12
country code 128, 164
D
Data Beacon Rate 142
default IP address 118
default user name and password 111
device location 115
device name 115
device settings 115
DHCP
release 119
renew 119
DHCP / Auto Configuration 119
DHCP Option 82 134, 148
diagnostics 181
disable Ethernet ports 146
DTIM 142
dual-band ZoneFlex Access Points 113
Dynamic VLAN 134
E
B
band selection 128, 129, 163
Beacon Interval 142
BeamFlex 12
BLE device support 184
Bluetooth low energy devices 184
Bridge to L2TP Tunnel 133, 147
Bridge to WAN 133, 147
broadcast SSID 133
C
changing the login settings 115
Channel Width 128, 164
Client Fingerprinting 134, 148
configuring LACP, LACP, configuring 186
controller
Smart Access Management service
(SAMs) 12
SmartCell Gateway (SCG) 12
Ekahau 129
encryption 134
Ethernet ports 16
configuration 146
External Antenna 129
F
factory default 180
factory defaults
resetting 18, 52
firmware upgrade 176
FlexMaster 82, 110
FlexMaster (FM) manager 12
FlexMaster management status 171
FlexMaster server address 88
FM (FlexMaster) manager 12
189
G
General Port 147, 149
H
H500 47
Help 112
Hotspot
basic settings 152
configuration 152
optional settings 154
unrestricted access 158
walled garden 157
Hotspot Service 134
I
installation 75
7441 100
H500 106
required tools 77
Internet settings 117
IP address 118
Isolated 133, 147
K
Key Index 136
L
L2TP 122
LACP 185
LAN5/Uplink 16
LEDs 17
link aggregation 185
Local Bridging 147
local subnet 124, 134, 147
Local Subnet NAT and Route to WAN
133, 147
location 78
logging in 110
logout 112
M
MAC authentication bypass 151
management access options 167
Management VLAN 118
manager, FM 12
MCS (modulation and coding scheme)
185
menu 112
modulation and coding scheme (MCS)
185
mounting recommendations 78
N
NTP Server 118
O
optimal mounting 78
orientation 78
P
package contents 13
packet forwarding 133, 147
pass through port 15, 16
Passphrase 139
ping 181
Port Type 147
port-based VLAN 146
PPPoE 122
Preconfiguring the AP 108
protection mode 131
punch down block 16, 99
R
R300 53
R500 56
R600 61
R700 66, 70
Radio Network 127
Rate Limiting 133, 143
rebooting 18, 52, 179
releasing DHCP 119
renewing DHCP 119
reset buttons 18, 52
resetting to factory default 180
router mode 124
RTS/CTS Threshold 142
running diagnostics 181
S
SAMs controllers 12
SCG controller 12
190
site survey 76
Smart Access Management service
(SAMs) controller 12
SmartCell Gateway (SCG) controller 12
SmartZone (SZ) controller 12
SmartZone software 12
SSID 133
standalone operation 82, 110
Static IP 120
syslog 173
SZ controller 12
T
tabs 112
temperature update 115
threshold 133
traceroute 181
transmit power 131
Trunk Port 147, 149
Tunnel via L2TP 133, 147
U
upgrading firmware 176
USB devices 184
user name 115
V
verifying operation 91
viewing associated clients 165
viewing device settings 160
viewing Internet settings 161
viewing Local Subnet settings 162
viewing wireless clients 165
viewing Wireless settings 163
virtual SmartZone (vSZ) controller 12
VLAN 146, 148
overview 117
wireless 134
VLAN Settings 117
vSZ controller 12
W
Web interface 112
web interface 110
WEP 135
WEP Key 136
wireless availability 132
wireless channel 128, 164

wireless mode 128, 129, 163
wireless security
802.11X 139
WEP 135
WPA 137
wireless settings 126
WISPr 152
WLAN
configuration 132
workspace 112
WPA 137
WPA Algorithm 139
WPA Authentication 139
WPA Version 138
WPA-Auto 138
Z
Z2 APs 184, 185
ZD controller 12
Zone 2 APs 184, 185
ZoneDirector 81, 82, 109
ZoneFlex 7055 15
ZoneFlex 7321 19
band selection 128, 129, 163
front panel 19
rear panel 21
ZoneFlex 7341 22
Front Panel 22
Rear Panel 24
ZoneFlex 7343 25
Front Panel 25
Rear Panel 27
ZoneFlex 7352 28
front panel 28
rear panel 30
ZoneFlex 7363 31
front panel 31
rear panel 33
ZoneFlex 7372 34, 37
front panel 34, 37
rear panel 36, 39
ZoneFlex 7441 41
front panel 41
ZoneFlex 7982 43
front panel 43
rear panel 45
ZoneFlex H500 47
bottom panel 51
191
front panel 48
rear panel 49
ZoneFlex R300 53
front panel 53
rear panel 55
ZoneFlex R500 56
front panel 56
rear panel 59
ZoneFlex R600 61
front panel 61
rear panel 64
ZoneFlex R700 66, 70
front panel 66, 71
rear panel 68, 72
192
Copyright 2006-2015. Ruckus Wireless, Inc.

350 West Java Dr. Sunnyvale, CA 94089. USA

Ruckus Indoor-AP User-Guide 100.2.0

Uploaded by

Copyright:

Available Formats

Ruckus Indoor-AP User-Guide 100.2.0

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ruckus Indoor-AP User-Guide 100.2.0

Uploaded by

Copyright:

Available Formats

Ruckus Wireless

Indoor Access Point

Release 100.2.0 User Guide

For the following indoor Ruckus Wireless AP models:

Part Number 800-70892-001 Rev B

Copyright Notice and Proprietary Information

Destination Control Statement

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

About This Guide

Introducing the Ruckus Wireless AP

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Configuring the AP for Management by an SCG, SZ or vSZ Controller . . . . . . . . . . . . . 81

Navigating the Web Interface

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Configuring Common Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

Appendix A: AP Support for Bluetooth Low Energy Devices

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

About This Guide

By downloading this software and subsequently upgrading Ruckus Wireless APs to

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

About This Guide

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

About This Guide

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

About This Guide

Represents information as it [Device name]>

Represents information that [Device name]> set

default font bold

Keyboard keys, software

On the Start menu, click All

Screen or page names.

Click Advanced Settings.

Information that describes important features or instructions.

Information that alerts you to potential loss of data or potential

Information that alerts you to potential personal injury.

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Introducing the Ruckus Wireless AP

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Introducing the Ruckus Wireless AP

Overview of the Ruckus Wireless AP

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Introducing the Ruckus Wireless AP

Unpacking the Ruckus Wireless AP

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Introducing the Ruckus Wireless AP

Getting to Know the AP Features

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Introducing the Ruckus Wireless AP

ZoneFlex 7055 Dual-Band Wired/Wireless Wall Switch

Front View Features

ZF7055 front view features

Pass Through port Pass through port.

Ruckus Wireless Indoor AP 100.2.0 User Guide, 800-70892-001 Rev A

Introducing the Ruckus Wireless AP

ZF7055 front view features (Continued)

Optional 48V DC power input.

Three 10/100 RJ-45 Ethernet Ports.

One 10/100 RJ-45 LAN port with PoE out. Supports

Refer to Reset Buttons on page 18 for details.