HMP1 User Manual.00

www.schdev.com.
ar
HMP 1-A
Model:
Electronic throttle tester
0120.00
Rev doc: 00
Users Manual
Connecting power supply

Selecting the right cable set
Making new cables
Plug the terminal block
Test an electronic throttle
Report on screen
Determining common fails
Troubleshooting
Short circuit protection
General warnings
Warranty
Pg. 1
Pg. 2
Pg. 3
Pg. 4
Pg. 4
Pg. 5
Pg. 5
Pg. 6
Pg. 6
Pg. 7
Pg. 8
Connecting power supply

The device need for work 12Vdc continuous. Become with 2
cocodriles to allow connect to car battery.
DO NOT USE battery chargers without a car battery.
1/8
Choosing the right cable

Before test any throttle body, the first is choose the right cable. For
this you must search in the following list, not only the right form, also
must check right connections.
This images are front view, seeing the throttle body.
A) Bosch 0280750085
Peugeot 307/Citroen C3,C4
Pin
Func.
Pin
Func.
Coil+
TPS2
Coil-
5V
GND
TPS1
Pin
Func.
Pin
Func.
GND
Coil+
TPS1
5V
Coil-
TPS2
B) Magnetti Marelli 44SMG2

Siena/Palio RST II 1.8
C) Magnetti Marelli 44SMF8/36SMF7 - Bosch 032133062

Siemens VDO 022133062 / 408238329001 / 036133062P
Fiat Palio/Siena 1.4,1.0 - VW Fox/Gol/Golf
/Polo/Bora/ - Audi
2/8
Pin
Func.
Pin
Func.
TPS1
TPS2
GND
Coil+
Coil-
5v
D) Bosch 0280750137
Fiat Punto / Viper / Dodge RAM
Pin
Func.
Pin
Func.
Coil+
Coil-
GND
TPS2
5V
TPS1
Pin
Func.
Pin
Func.
5V
GND
TPS2
Coil+
TPS1
Coil-
Pin
Func.
Pin
Func.
5V
TPS1
TPS2
GND
Coil-
Coil+
E) Delphi-GM 93397800/94705389/24579418
Chevrolet Corsa/Meriva/Montana 1.4/1.8
F) Hitachi SERA576
Nissan 350z
Unconfirmed Pinout
New cables
In the future you will add new
connectors. So you will need know
about device connections looking the
image.
3/8
Connecting terminal block

Once you choose the appropriate cable you must plug in the
rear connector.
Testing of electronic throttle

1) THE ENGINE MUST BE STOPPED. The engine can be
damaged if is over accelerated moving the butterfly manually.
2) Choose the appropriate cable, check the connections,
specially the coil connection in the cable A & cable B.
3) Plug 12Vdc and throttle body and wait for plug throttle
letter, then press OK.
4.A) Pressing the button + the butterfly open
4.B) Pressing the button - the butterfly close
4.C) Pressing + y - simultaneously the butterfly will open &
close continuously.
Into the screen you can see the coil current, and the sensors
data. The TPS1 + TPS2 must be equal to 100 in all moment.
The maximun acceptable difference can vary from car to car,
but generally the difference is lower than 3%.
4/8
Report on screen
After moving the butterfly from extreme to extreme, the devie
have all information to show the test result.
Press the button OK.
Result 1: integrity of TPS1, will show the minimum and
maximum TPS1 data.
Result 2: integrity of TPS2, will show the minimum and
maximum TPS2 data.
Result 3: The maximum difference between TPS1 & TPS2,
normally 3% (100-(T1+T2)).
Result 4: The maximum current of the coil. This is important to
discard short circuits.
When the report end, all data are erased to a new test.
Determining common fails
-The coil have consumption, but the butterfly didn't move.
Exhausted gears.
-The difference between TPS1&TPS2 is more than 5%.
TPS dirty or exhausted.
-The movement is not smooth.
Suciedad, o engranaje daado
5/8
-The throttle body is ok, but the car have

idle problems.
Dirty in the closing point, normally dust is
accumulated between the butterfly and the
venturi. Clean with dirty cloth.
Most common trouble solutions
The device does not power up.
- Verify the right connection to 12V.
The butterfly close and the screen show Short Error.

-A short circuit is detected. The system will stay freezed until you
push OK button.
The butterfly close and the screen show Fuse Error.

-The internal fuse is opened due coil consumption excess. Wait few
minutes and press OK button. The fuse is automatically restored.
With the butterfly, the TPS1 show more than 50% and/or
the TPS2 show few than 50%.
-TPS1 & TPS2 are inverted
-TPS1 or TPS2 is damaged.
Short circuit protection

The device have a over consumption protection that abort the
test and show on screen until you press the OK button.
The device can be damaged in short circuits, and this
damages will void the warranty.
6/8
General Warnings
-Do not wet the device, do not use chemicals to clean. Only a
slightly damp cloth.
-This device must do not enter in touch with hydrocarbons.
(Oil, Gas, Diesel, alcohol, etc etc etc)
-Do not connect the device to any voltage different to 12V.
-Do not plug more than one throttle body at once.
Note: The content of this manual can be changed in any
moment without notice. ---- SCHdev take all rights to make
the all changes that consider convenient to the manual and
product with the end to improve.
Note 2: All mentioned trademarks in this manual are propriety
of their respective owners and only are mentioned with the only
idea that the customer identify correctly the components.
7/8
Warranty conditions
-General condition of warranty
SCHdev, warrant the right working of this product.
The warranty is for the following 3 (three) months starting in the purchase date, this cover
the materials and had handwork defects.
If while warranty is running, the device fail, SCHdev will repair the product. The repair
work is done into SCHdev placement and the shipping cost will be charged to the
customer.
All accessories that not are manufactured by SCHdev, the warranty are keeped by the
respective providers.
This warranty is the only gived by SCHdev, so any other claim are excluded.
- Conditions
The warranty only will be recognized with the presentation of this certificate with the date
of purchase, or the bill of purchase. The present warranty only will work with the customer
that are at day with the payments.
- Execution of warranty
1.- Periodic controls, maintenance, reparations, and pieces substitutions of pieces or spare
parts as result of normal usage.
2.- Any malfunction due bad usage, shocks, or usage out of specifications and any defect
not produced by defect of construction.
3.- Product, installed, modified, repaired, mounted or handled by personal unauthorized by
SCHdev.
4.- Accidents due to force major or other causes (water, fire, lightning, electromagnetic
fields, etc.) that do not depend SCHdev.
You can see other SCHdev products

HRR2: stepper motor & IAC valves tester
LPA3: Automatic lights turning ON
GLC3: Closed loop for NGV cars
GNC2: Digital indicator for NGV cars
SCH dev
Tel: 54 11 4639-5945
8/8
http://www.schdev.com.ar
El araucano 1389 Cap Fed - Argentina.

HMP1 User Manual.00

Uploaded by

Copyright:

Available Formats

HMP1 User Manual.00

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HMP1 User Manual.00

Uploaded by

Copyright:

Available Formats

www.schdev.com.

Connecting power supply

Connecting power supply

Choosing the right cable

B) Magnetti Marelli 44SMG2

C) Magnetti Marelli 44SMF8/36SMF7 - Bosch 032133062

Connecting terminal block

Testing of electronic throttle

-The throttle body is ok, but the car have

The butterfly close and the screen show Short Error.

The butterfly close and the screen show Fuse Error.

Short circuit protection

You can see other SCHdev products

You might also like