Scribd Logo
Upload

Welcome to Scribd!

  • 73 views

    Rb2011u QG

    Uploaded by

    e_gerla
    router

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Rb2011u QG

    Uploaded by

    e_gerla
    73 views2 pages
    router

    Original Title

    rb2011U-qg

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    router

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    73 views2 pages

    Rb2011u QG

    Uploaded by

    e_gerla
    router

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    RouterBOARD

    2011U series
    Quick Setup Guide and Warranty Information
    The RB2011U is a small form factor ethernet router with 5 Gigabit Ethernet ports and 5 Fast Ethernet ports and an SFP cage.
    The RB2011L series includes four models, RB2011UAS-IN (USB, SFP, indoor case), RB2011UAS-RM (USB, SFP, rackmount
    case), RB2011UAS-2HnD (adds wireless AP function) and RB2011UAS-2HnD-IN (adds indoor case)

    First use
    The device comes preinstalled with RouterOS and is ready to use. RB2011 is compatible with RouterOS v5.9 and newer, if
    your device comes preinstalled with an earlier version, please upgrade before using it.
    The Ethernet ports 2-10 have a default IP address for connecting: 192.168.88.1 username is admin and there is no password.
    Please connect with your web browser to this IP address and choose Webfig to configure it. Ether1 is configured as a DHCP
    client, for connecting to your ISP.
    See this page for connection and configuration guides: http://wiki.mikrotik.com/wiki/Category:Manual

    Powering
    The device accepts powering from either the power jack, or from the LAN1 Ethernet port:

    Direct-input power jack (5.5mm outside and 2mm inside diameter, female, pin positive plug) accepts
    8-30V DC (overvoltage protection starts at 30V).
    Eth1 port accepts 8-30V DC input (at the board; higher voltage needed to compensate for power loss on long cables)
    from non-standard (passive) Power over Ethernet injectors. The board does not work with IEEE802.3af compliant
    48V power injectors
    The IN and RM models include a 110/220V PSU which is already plugged into the power jack inside the case

    Extension Slots and Ports

    Five 10/100/1000 (Gigabit) Ethernet ports (Auto MDI/X)


    Five 10/100 (Fast) Ethernet ports (Auto MDI/X)
    One 8-30V DC power jack
    SFP port for SFP module (module not included, works only with Gigabit modules)
    (only on RB2011UAS-2HnD-IN) built in wireless AP (2GHz , 802.11b/g/n), with external antennas.

    See www.routerboard.com for more information. Contact [email protected] for support questions.

    3-May-2013

    Resetting the device


    In case you wish to return the device to its original configuration, you can use the RESET button (image Reset1). Hold this
    button during boot time until LED lights start flashing, then release the button to reset RouterOS configuration. You can use
    this procedure if you have forgotten the password to access the device, or simply wish to return the unit to its default config-
    uration state.

    Buttons and Jumpers

    RouterBOOT reset button (image Reset1) has several functions:


    Hold the button before powering on the device, and at power up, the button will force load the backup boot-
    loader. Continue holding the button for the other two functions of this button:
    Release the button when green LED starts flashing, to reset RouterOS configuration. To not load backup boot-
    loader, you can start holding the button after power is already applied
    Release the button after LED is no longer flashing (~20 seconds) to cause device to look for Netinstall servers
    (required for reinstalling RouterOS over network)
    RouterOS reset jumper hole (image Reset2): resets RouterOS software to defaults. Hold screwdriver pressed to this
    reset hole, and boot the device. Hold screwdriver in place until RouterOS configuration is cleared (10 seconds).

    Operating System Support


    Currently tested operating system is MikroTik RouterOS (starting from version 5.9).

    Warranty
    Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part
    of it may be reproduced or transmitted in any form without prior written permission from the copyright holder. Router-
    BOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks
    appearing in this manual are the property of their respective holders.
    Hardware. MikroTik warrants all RouterBOARD series equipment for the term of one year from the shipping date to be free
    of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical,
    electrical or other accidental or intended damages caused by improper use or due to wind, rain, fire or other acts of nature.
    To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Fol-
    low the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process.
    1.

    2.
    3.

    If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all war-
    ranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly from
    MikroTik in Latvia.
    We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000, RB1100
    and RB1200.
    Out-of-warranty devices and devices not covered by warranty sent to Mikrotik will be returned to the sender at
    sender's cost.

    RMA Instructions are located on our webpage here: http://rma.mikrotik.com


    Manual. This manual is provided as is without a warranty of any kind, expressed or implied, including, but not limited to,
    the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to en-
    sure the accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies, typo-
    graphical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, inci-
    dental, consequential or other damages that may result from such an inaccuracy, including, but not limited to, loss of data or
    profits. Please report any inaccuracies found to [email protected]

    See www.routerboard.com for more information. Contact [email protected] for support questions.

    3-May-2013

    You might also like