File 46392

Episode 214: Work done by a force
In this episode, students have to learn to think of force as a mechanism by which energy is
transferred from one body to another. This only occurs when the force moves in the direction of
the force.
Summary
Discussion: Introductory discussion. (10 minutes)
Student experiment: Efficiency of a ramp. (25 minutes)
Student questions: Calculations of work done. (30 minutes)
Discussion:
Introductory discussion
For some students this will be a revision session. Others may be less familiar with the concepts.
Use questions and answers to establish the knowledge of the group.
We say that work is done by a force when the
object concerned moves in the direction of
the force, and the force thereby transfers
energy from one object to another. You can
be a typical physics teacher and use a board
rubber to illustrate your point about energy
gain. Alternatively, use some other more
interesting object such as a model
Thunderbird One. The following questions
should allow you to draw out the ideas used
the experiment which follows:
in
What sort of energy is gained by raising a mass (board rubber etc)? (GPE)
What is the force acting against the movement? (mg) We say that the lifting force is doing work
against gravity. Some students may feel that it takes a larger force than mg to raise the object;
however, if the object is raised at a steady speed, it is in equilibrium and the lifting force will just
balance weight. This of course ignores any air resistance etc
What is g? (You are looking for gravitational field strength here, not acceleration due to gravity;
you may need to draw this point out.)
What two factors will determine how much energy you lose (and hence the energy transferred to
the object)? (The size of the force and the distance h moved in the direction of the force.)
Can you state the equation which gives the energy gained? (mgh)
Hence how much energy is required to lift object height h? (mgh)
This suggests that energy transferred = force distance moved in direction of force. This is
known as the work done by the force. In fact, we have used the fact that students are familiar with
the equation GPE = mgh to lead them to the more general equation for work done. You should
now point out that mgh is simply a particular case of work done.
You can now push the board rubber or thunderbird across the lab bench to show work being done
against a frictional force. In this case, the energy transferred ends up as heat.
Student experiment:
Efficiency of a ramp
You may want to show the apparatus set up before the students attempt this experiment and
show them how to get the block moving smoothly. The values of the masses to overcome friction
depend on the apparatus you are using and therefore the experiment needs to be trialled before
the lesson. Using a pulley system should allow the students to get reasonably consistent results.
This simple experiment is made more interesting by revising the resolution of forces and
considering the total work done to be the sum of work against gravity and work against friction.
This concept is reiterated in the questions (below).
TAP 214-1: Work done in raising a weight using a ramp
Student questions:
Calculations of work done
You may choose to use some of these in the class as discussion questions, or as worked
examples.
TAP 214-2: Along the flat and up the hill
TAP 214-1: Work done in raising a weight using a ramp

Set up the apparatus as shown in the diagram.
Retort stand
and bosses
Pulley
String
Variable
mass
Slope
Lab bench
Wooden block
Lab bench
Measure and record the mass of the wooden block.
Mark the position of the wooden block at the bottom of the slope.
Carefully add mass to the end of the string until the wooden block just starts to move.
Experiment until you are happy that the block is just moving up the slope. Record the
pulling mass.
When the block comes to a rest (usually because the pulling mass has hit the floor)
measure how far the block has moved along the slope.
Calculate the work done in pulling the block up the slope.
Measure how high the wooden block has been raised (i.e. the vertical distance moved).
Think carefully how you might do this accurately.
Calculate the gravitational potential energy gained by the block.
Compare the work done by the falling variable mass to the GPE gained. What do you
notice? Can you explain this?
Calculate the efficiency of the ramp system in lifting the weight:

efficiency = potential energy gained 100%
work done
Analysis of forces on the block:
N
F
Copy the diagram above and add the frictional force.
At equilibrium, when the block is moving up the slope with constant velocity:
magnitude of force F = magnitude of frictional force + component of W acting down the slope
Use this relationship to estimate the frictional force acting down the slope.
Calculate the work done against friction in pulling the block up the slope.
If the block is pulled very slowly up the ramp the expression:

Potential energy gained + work done against friction = total work done
is reasonably accurate.
Test this expression using your results and suggest a reason for any discrepancies.
TAP 214- 2: Along the flat and up the hill

Think carefully, and calculate a little.
Two speeds, one principle.
Travelling slowly, at about 5 miles an hour, the retarding forces acting on a cyclist are about 5 N.
1.
What propulsive force must the cyclist provide to travel at constant speed?
2.
How much energy does the cyclist have to provide to cover 5 m?
At a higher speed, nearly 10 mph the retarding forces are much larger, nearly 8 N.
3.
Write down the propulsive force required at this speed.
4.
Calculate the energy the cyclist must provide every to cover 5 m at this constant speed.
Climbing a hill at a steady speed of 5 mph the cyclist finds herself perspiring rather more than on
the flat. The mass of the cycle plus cyclist is 80 kg. The ergometer pedals fitted report the energy
supplied to the bicycle as 185 J to cover a 5 m stretch of road.
5.
How much energy is used to lift the cyclist uphill?
6.
How much height does she gain in travelling along the 5 m stretch of road?
7.
How much energy would she have to provide to cover this same stretch of road at 10
mph?
8.
What is the retarding force acting on her, when travelling uphill at 10 mph?
9.
Draw a vector diagram for the retarding forces (due to drag and gravity) acting on her at
10 mph.
10.
Calculate the retarding force due to the slope as a fraction of her weight. Comment on
the advantages of using the slope of the hill rather than lifting bike and rider vertically by
the same distance
Practical advice
These are intended to start at a very low level, building up to thinking about forces not along the
line of movement affecting energy changes.
Social and human context

The energy to surmount even a small hill has appreciable effects on the power requirements. So,
prior to the invention of the internal combustion engine, with its very high power / all up-weight
ratio, engineers had to respect the landscape, trading larger distances covered for more gentle
gradients.
Answers and worked solutions

1.
Net force must be zero, so 5 N
2.
Work force distance

5m 5N
25 J
3.
Net force must be zero, so 8 N
4.
Work force distance

5m 8N
40 J
5.
energy to lift energy supplied energy dissipated

185 J 25 J
160 J
6.
Energy transferred m g h
160 J
h
80 N 10 N kg 1
0 .2 m
7.
energy supplied energy to lift energy dissipated
160 J 40 J
200 J
8.
Energy transferred force distance
200 J
force
5m
40 N
9.
drag
retarding force
due to gravity
10.
ratio
32 N
4%
800 N
External references
This activity is taken from Advancing Physics, Chapter 9, Question 240W.

File 46392

Uploaded by

Copyright:

Available Formats

File 46392

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

File 46392

Uploaded by

Copyright:

Available Formats

Episode 214: Work done by a force

TAP 214-1: Work done in raising a weight using a ramp

TAP 214-1: Work done in raising a weight using a ramp

Measure and record the mass of the wooden block.

Calculate the work done in pulling the block up the slope.

Calculate the gravitational potential energy gained by the block.

Calculate the efficiency of the ramp system in lifting the weight:

Copy the diagram above and add the frictional force.

If the block is pulled very slowly up the ramp the expression:

TAP 214- 2: Along the flat and up the hill

How much energy does the cyclist have to provide to cover 5 m?

Write down the propulsive force required at this speed.

How much energy is used to lift the cyclist uphill?

Social and human context

Answers and worked solutions

Net force must be zero, so 5 N

Work force distance

Work force distance

energy to lift energy supplied energy dissipated

You might also like