Elite 440: Multi-Line Three-Phase Panel Meter

Elite 440
Multi-line Three-phase Panel Meter
Elite 440 is a multi-line three-phase digital panel meter for

accurate and reliable measurement of electrical parameters
(voltage, current, power, frequency, etc.) for industrial and
commercial applications. It has a large multi-line backlit LCD
display which enables four parameters to be displayed at the
same time. Modbus communication capability allows easy
integration with energy monitoring systems. Expansion
modules can be fitted for enhanced system integration (pulse
inputs/outputs or analogue output and ethernet).
Applications
Features
Commercial and industrial sub-metering and energy
Large four-line seven-digit display (9.7 H x 5 W mm) with
management (EMS) applications.

Building management and monitoring systems (BMS)
High, medium and low-voltage switchgear panels
Control and relay panels
Power Control Centre (PCC) panels
Motor Control Centre (MCC) panels
Relaying and control outputs
Plant automation and monitoring system (SCADA/DAS)
Benefits
Easy interface with external devices through built-in Modbus
(RS-485/Ethernet)
Detachable connectors for easy installation
Diagnostics assistance on display
Suitable for star or delta connections and for low or high-
voltage applications
Cost-effective online monitoring
Field-configurable CT/PT primary and secondary values using
push-buttons
quadrant identification section and bar graph for

instantaneous power-level indication
High accuracy: Class 0.2s, 0.5s, 1.0
Average THD measurement for voltage, current and power,
up to 31st harmonic
Measurement selection (star or delta/ 3P4W or 3P3W)
Modbus communication via RS-485 port/ethernet
True root-mean squared (RMS) metering
Calibration LED for accuracy test on site
Wide and configurable current range 1-2A and 5-10A
Wide-range auxiliary power supply, suitable for high-voltage
or low-voltage installations
Maximum demand recording
Midnight snapshot ( values) for selected energy registers
Scroll-lock and 'Favourites Page' display support
Expansion capability via add on modules for analogue
outputs or pulse inputs/outputs and ethernet
Password protection for setup mode
Ethernet gateway module for easy integration of multiple
meters connected over RS485 network
Elite 440
Features
Models
441
442
443 444
445
P-N voltage
Average P-N voltage
P-P voltage
Average P-P voltage
Line current (L1, L2, L3 and Average)
Active / Reactive Current
Frequency
Power factor
Average Power factor
Active Power
Total Active Power
Reactive Power
Total Reactive Power
Apparent Power
Total Apparent Power
Active Total Import / Export Energy
Reactive Import (Q1+Q2) / Export (Q3+Q4) Energy
Reactive (Q1,Q2,Q3,Q4) Energy
Apparent Import / Export Energy
Active / Apparent Forwarded Energy
Reactive Lag / Lead Forwarded Energy
Cumulative MD
Phase Angle
Power On / Off Hours
Load On / Off Hours
Feeder Interruptions Count (When Aux is also off)
Min / Max Values
THD Voltage
THD Current
THD Power
RPM with Freq and VUnb and IUnb
Modbus on RS 485
Note:
Ethernet (add on) module is available for all Elite 440 models as single meter module or gateway
Additional modules (Two pulse input & output or four analogue outputs) can be available in Elite 443 to Elite 448
# Optional software config view is available for reading and configuration
446
447
448
Elite 440
Metering Parameter Accuracy
Parameters
Accuracy Class 0.2
Accuracy Class 0.5
Accuracy Class 1.0
Voltage
0.1
0.1
0.1
Current
0.1
0.2
0.2
kW
0.2
0.5
0.5
kVar
0.2
0.5
0.5
kVA
0.2
0.5
0.5
kWh
0.2
0.5
1.0
kvarh
0.2
0.5
1.0
Frequency*
0.1
0.1
0.1
* 0.05 optional
Connection Diagram
LT34W
HT33W
HT34W
1
2
3
1
2
3
1
2
3
N
V1 V2 V3 VN
AUX
+/P -/N
S1 S2 S1 S2 S1 S2
I1
I2
RS-485
+
S1 S2 S 1 S2 S1 S 2
I3
I1
I2
V1 V2 V3 VN
I3
AUX
+/P -/N
- SG
Auxiliary P
supply N
AUX
+/P -/N
RS-485
- SG
RS-485
- SG
Auxiliary P
supply N
Auxiliary P
supply N
In case of CT/PT operated
meter, ensure that meter is
connected on secondary side
of instrument transformer.
S1S2 S1S2 S1S2

I1
I2
I3
V1 V2 V3 VN
In case of 33W, VN is
replaced by V2 .
SHORT CTs BEFORE OPENING

CURRENT TERMINALS
Mechanical Dimensions
Available Option
(2 Pulse input & output) Or
4 analogue outputs
m
65 m
96 m
m
45 m
57
65
mm
96 mm
mm
56 mm
55 mm
96
6 mm
96 mm
m
45
58 m
Meter without module
I/O module
Ethernet module
Ethernet
Meter with module
Elite 440
Technical specifications
Common product for HT3/ HT4/ LT application
Common product for 3 P-3 W and 3 P-4 W application
Short time over current
57.7 V (100V) - 240 V (415 V) AC 3 phase 4 wire (3 phase 3 wire)

-30% to +20% of Vn
80 - 300 V AC/DC or 24 - 60 V DC (Variant)
Available 1-2A and 5-10 A in single variant (field configurable)
50/60Hz with 5%
0.2s, 0.5s, 1.0
Aux burden : 3.5 VA; 8VA when all modules connected.
Current ckt burden : 1 A - 0.05VA per phase, 5 A - 0.25 VA per phase.
Voltage ckt burden : 0.15 VA per phase.
20 x Imax for 1 sec., 10 x Imax for 3 sec., 7 x Imax for 10 sec.
Approvals
Standards
IS13779, IS14697, IEC62052-11, IEC62053-23 and IEC62053-22, IEC61010, IEC62053-31
Mechanical
Dimensions (WXHXD)
Weight
Enclosure
Terminals
Max conductor size
Environmental
Ingress protection
Insulation
Impulse withstand
Temperature
Humidity
Feature
Favourite page
CT/VT primary
Communication
Baud rate
Load survey
Modules
2 Digital pulse input and output (single module)
Ethernet
4 analogue outputs
96 x 96 x 65 mm (w/o module);
96 x 96 x 110 mm (with module)
Cut out size 92 x 92 mm
0.5 kg (approx)
FRPC
Combicon connector
2
2.5 mm
IP 52 (front fascia); IP20 (at terminals)

4 kV RMS 50 Hz, 1 minute
6 kV
-20 C to +60 C (operating)
-25 C to +80 C (storage)
95% non-condensing
On / Off
Configurable in field through keypad
RS485 Modbus half duplex (Default) and data will be available in floating point format
(IEEE754)
From 1200-38400 bps (Default 9600 bps)
40 days for 6 parameters @ 30 minutes integration period
Options for 15 or 60-minute integration period.
Input supports voltage range of 8-40VDC with pulse duration of 5 ms for input 1 and
40 ms for input 2. Output are normally open type, voltage rating of 230 V AC @ 100 mA or
48 V DC @ 100 mA with pulse width of 80 ms or 240 ms
10/100base-T for Modbus over TCP/IP communication
Analogue output supports current range of 4-20 mA non-isolated with loop impedance
750 , auxiliary supply 20-40V DC @ 100 mA
Secure Meters Limited

P.O. Box No. 30, E-Class Pratap Nagar Industrial Area, Udaipur 313003, INDIA
T: 91-294-2492300-04 | F: 91-294-2492310 | E:[email protected] | www.securetogether.com
Brochure Version Number - 2.4
Specifications are subject to change without prior notice
Electrical
Connection type
Wiring configuration
Voltage range :
Measurement voltage range
Tolerance
Aux power supply range
Current range
Main frequency
Accuracy Class
Burden
Elite 200
Digital Panel Meter
Elite 200 is a digital panel meter specially designed for

dual-source energy metering. It has two registers for recording,
separately the energy consumption from the mains and auxiliary
supplies (such as a diesel generator).
It also provides load control so that the supply can be
disconnected if the load exceeds a pre-set limit.
This is
particularly useful for installations where the auxiliary supply

has a lower capacity than the mains.
The Elite 210 variant provides Modbus communication over
RS-485 for online monitoring applications.
Applications
?
Metering of dual-supply installations (mains and backup
generator)
?
Load control applications
Features
?
Accuracy class 1.0 and 0.5s
?
Separate energy registration for mains and backup supply
(such as DG)
?
Online monitoring systems
?
Forwarded energy registration in case of current reversal
?
Commercial and industrial sub-metering applications
?
Accurate readings even at very low current
?
Compact DIN 96 panel meter
Benefits
?
Open-circuit protection for external CTs
?
Easy interfacing with external devices through pulse I/O
?
Minimal installation costs through easy fitting and
detachable connectors
?
Cost-effective online monitoring
?
Helps consumers monitor their consumption
?
One pulse input for switching of metering between mains
and DG
?
One pulse output for load control (load monitoring based
on average load over the last 60 seconds)

?
Power On/Off hours recorded for mains supply and
backup supply
?
Time of day tariff registration with maximum demand and
billing history recording

?
Optional RS-485 Modbus communications (floating point
as per IEEE-754 or hexadecimal format)

?
Self-diagnostic displays for checking connections
?
Meter configuration through push buttons, including CT
primary value
?
Optical port for local and remote reading
Elite 200
Technical specifications
Electrical
Connection type
Wiring configuration
Voltage range
Current range
Overload
CT-operated
3-phase 4-wire
240 V (L-N) / 415 V (L-L)
1-1.2 A , 5-6 A
Withstand up to 130 % Imax continuous, 20 x Imax for 0.5 s
Accuracy
Mains frequency
Burden
Class 0.5s ,1.0

50 Hz 5%
Voltage circuit : < 1.5 W, < 1 VA
Current circuit : < 0.5 VA
Compliance
Standards
IS14697, IS13779
IEC 62052-11, IEC 62053-21, 22, 23
Mechanical
Dimensions (W x H x D)
Cutout size
Depth behind bezel
Weight
Enclosure
Terminals
96 x 96 x 115 mm
92 x 92 mm (DIN 96)
84 mm
0.4 kg (approx.)
Polycarbonate
Combicon connector
Max. conductor size
2.5 mm
Environmental
Ingress protection
Dielectric strength
Isolation
Impulse withstand
Temperature
Humidity
IP 50 (front panel)
4 kV RMS, 50Hz
6 kV
-10 C to +55 C (operating)
-25 C to +70 C (storage)
95% non-condensing
Features
Custom backlit LCD
Configurable via keypad
Programmable via keypad
PACT port, Modbus via RS-485 port
1200, 2400, 4800, 9600, 19200 bd (field-configurable through keypad)
240 V AC
100 mA DC max
Specifications are subject to change without prior notice
Display
Favourite page
CT/VT primary
Communications
Baud rate (Modbus)
Pulse output (for load control)
Voltage rating
Current rating
Pulse input
Voltage rating
Current rating
Variants for 12-40 V DC or 60-240 V AC

100 mA DC max
Secure Meters Limited

P.O. Box No. 30, E-Class Pratap Nagar Industrial Area, Udaipur 313003, INDIA
T: 91-294-2492300-04 | F: 91-294-2492310 | E:[email protected] | www.securetogether.com

Elite 440: Multi-Line Three-Phase Panel Meter

Uploaded by

Copyright:

Available Formats

Elite 440: Multi-Line Three-Phase Panel Meter

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Elite 440: Multi-Line Three-Phase Panel Meter

Uploaded by

Copyright:

Available Formats

Elite 440

Multi-line Three-phase Panel Meter

Elite 440 is a multi-line three-phase digital panel meter for

Commercial and industrial sub-metering and energy

Large four-line seven-digit display (9.7 H x 5 W mm) with

management (EMS) applications.

Easy interface with external devices through built-in Modbus

Diagnostics assistance on display

Suitable for star or delta connections and for low or high-

quadrant identification section and bar graph for

Accuracy Class 0.2

Accuracy Class 0.5

Accuracy Class 1.0

S1S2 S1S2 S1S2

SHORT CTs BEFORE OPENING

Meter without module

Meter with module

Short time over current

57.7 V (100V) - 240 V (415 V) AC 3 phase 4 wire (3 phase 3 wire)

IS13779, IS14697, IEC62052-11, IEC62053-23 and IEC62053-22, IEC61010, IEC62053-31

IP 52 (front fascia); IP20 (at terminals)

Secure Meters Limited

Specifications are subject to change without prior notice

Elite 200 is a digital panel meter specially designed for

particularly useful for installations where the auxiliary supply

on average load over the last 60 seconds)

billing history recording

as per IEEE-754 or hexadecimal format)

Class 0.5s ,1.0

Max. conductor size

Specifications are subject to change without prior notice

Variants for 12-40 V DC or 60-240 V AC

Secure Meters Limited

You might also like