Scribd Logo
Upload

Welcome to Scribd!

  • 220 views

    Epdm

    Uploaded by

    Parashuram Chauhan
    EPDM is a synthetic rubber waterproofing membrane produced by ARDEX ENDURA that is resistant to aging from heat, sunlight, and ozone. It has excellent water vapor impermeability and flexibility from -40°C to 110°C. The membrane is available in thicknesses of 1.0mm or 1.5mm and widths of 1.35m, and is fixed to substrates using solvent-based contact adhesives or mechanical fixings. Substrates must be dry and free of contaminants, with concrete cured for at least 28 days prior to application. Seams are bonded using seam primer and tape.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Epdm

    Uploaded by

    Parashuram Chauhan
    220 views2 pages
    EPDM is a synthetic rubber waterproofing membrane produced by ARDEX ENDURA that is resistant to aging from heat, sunlight, and ozone. It has excellent water vapor impermeability and flexibility from -40°C to 110°C. The membrane is available in thicknesses of 1.0mm or 1.5mm and widths of 1.35m, and is fixed to substrates using solvent-based contact adhesives or mechanical fixings. Substrates must be dry and free of contaminants, with concrete cured for at least 28 days prior to application. Seams are bonded using seam primer and tape.

    Original Description:

    EPDM

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    EPDM is a synthetic rubber waterproofing membrane produced by ARDEX ENDURA that is resistant to aging from heat, sunlight, and ozone. It has excellent water vapor impermeability and flexibility from -40°C to 110°C. The membrane is available in thicknesses of 1.0mm or 1.5mm and widths of 1.35m, and is fixed to substrates using solvent-based contact adhesives or mechanical fixings. Substrates must be dry and free of contaminants, with concrete cured for at least 28 days prior to application. Seams are bonded using seam primer and tape.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    220 views2 pages

    Epdm

    Uploaded by

    Parashuram Chauhan
    EPDM is a synthetic rubber waterproofing membrane produced by ARDEX ENDURA that is resistant to aging from heat, sunlight, and ozone. It has excellent water vapor impermeability and flexibility from -40°C to 110°C. The membrane is available in thicknesses of 1.0mm or 1.5mm and widths of 1.35m, and is fixed to substrates using solvent-based contact adhesives or mechanical fixings. Substrates must be dry and free of contaminants, with concrete cured for at least 28 days prior to application. Seams are bonded using seam primer and tape.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    EPDM

    Waterproofing membrane

    ARDEX ENDURA (INDIA) PRIVATE LIMITED


    Corporate Office & Regd. Office:
    Unit No. 406 & 407, Brigade Rubix,
    No. 20, HMT Campus, Yeshwanthapur Hobli,
    Bengaluru - 560013. Karnataka, INDIA.
    CIN No: U24233KA1997PTC022383
    Tel: +91 80 66746500
    Fax: +91 80 66746540
    Email: [email protected]
    Visit us: www.ardexendura.com

    EPDM

    Waterproofing membrane

    DESCRIPTION

    A synthetic rubber with properties which resist


    ageing from heat, sunlight and ozone. It has
    excellent water vapour impermeability and
    toughness and remains flexible at low
    temperatures.
    EPDM is marketed by ARDEX ENDURA as a
    warranted roofing, decking and tanking product
    and fixed by their trained and experienced
    approved Applicators.

    bonding should not be proceeded with under


    four hours, thus allowing full evaporation of
    solvents absorbed into the substrate. Primers
    must be time dried not touch dried.
    As new substrate materials continually appear
    on the market, consult (Contact
    ARDEX ENDURA central technical service
    department for more details) for approval of
    their use with EPDM.
    Seam tape and seam primer must be used for
    all EPDM joints.

    SUBSTRATE SPECIFICATION

    Plywood & Timber Substrates must be dry


    when ARDEX ENDURA EPDM is applied. The
    plywood and timber substructure shall have a
    maximum moisture content of 20% when
    EPDM is adhered.
    NOTE: LOSP (Light Organic Solvent

    Preservative) treated plywood must NOT be


    used under EPDM under any circumstances.
    New Concrete must be cured for a minimum of
    28 days and all curing compounds removed
    prior to application. A reduction in cure time
    can be achieved by utilising the Ardex
    HydrEpoxy System (Contact ARDEX ENDURA
    central technical service department for more
    details)
    Old Concrete must be clean from any
    contaminants prior to application

    Do not use in temperatures less than 6C.


    APPLICATION

    Unroll the membrane over the substrate and


    allow it to relax for approximately 30 minutes
    before seaming or flashing. Membranes are
    overlapped, side lap and end laps in
    accordance with the installation instructions
    and details.
    PACKAGING

    Thickness
    Width
    Length

    1.00mm
    1.35m
    25m

    1.5mm
    1.35m
    20m

    STORAGE AND SHELF LIFE

    Store away from sources of puncture and


    physical damage. Store away from ignition
    sources and open flame. Unlimited shelf life.

    ADHESIVES

    1. ARDEX ENDURA WA98, the solvent based


    contact adhesive for brushing, spraying and
    roller application for fixing to the substrate.
    Supplied in 20L plastic containers. The
    Coverage of ARDEX ENDURA WA 98.
    2. Use Ardex Seam Primer and Seam Tape for
    laps
    WA98 - The Standard contact brushing,
    spray grade and rolling adhesive for fixing to
    the substrate and for laps not subject to
    periodic ponding. (Pitch 5 and above)
    WA98S - Solvent for cleanup of WA98 adhesive.
    Seam Primer - A water resistant primer, used
    with seam tape for general lap bonding.
    Note: Temperature and Humidity
    The evaporation of any solvent adhesive
    system causes a drop in temperature at the
    interface. At times of high humidity this can
    result in a micro molecular water layer at the
    interface which will result in a failure to bond,
    falsely attributed to Adhesive failure. Fixing
    should not proceed under these circumstances.

    DISPOSAL/SPILLAGE

    Spillage of any of the component products


    should be absorbed onto sand or other inert
    materials and transferred to a suitable
    disposable vessel. Disposal of such spillage or
    empty packaging should be in accordance with
    local waste disposal authority regulations.
    For further information please refer to the
    Material Safety Data Sheet.
    PRECAUTIONS

    Exercise caution when lifting, moving,


    transporting, storing or handling membrane
    rolls to avoid sources of puncture and possible
    physical damage.
    CONDITIONS OF SALE

    Sold subject to the Company's conditions of


    sale which are available on request.
    NOTE

    The information supplied in this datasheet is


    based upon extensive experience and is given
    in good faith in order to help you. Our Company
    policy is one of continuous Research and
    Development; we therefore reserve the right to
    update this information at any time without
    prior notice. We also guarantee the consistent
    high quality of our products; however as we
    have no control over site conditions or the
    execution of the work, we accept no liability for
    any loss or damage which may arise as a
    result thereof.

    TECHNICAL CHARACTERISTICS
    Property

    Value

    Test Method

    Specific Gravity

    1.2 0.05

    ASTM D297

    Hardness IRHD
    Tensile Strength MPa Min
    Elongation at Break

    68 5
    8.3
    300 % Min

    ASTM D1415
    ASTM D412
    ASTM D412

    Heat Aging 7 days at 115C


    Tensile Retention Min
    Elongation Retention

    70%
    70%

    Ozone Resistance 7days at 40C 50 pphm Ozone

    No Cracks

    ASTM D1149

    Water Absorption 7days at 70C change in mass

    4% max

    ASTM D471

    Water vapour Permeance at 23C, 45% RH, perms

    0.06 max

    ASTM E96

    Remains Flexible from

    -40C to +110C

    Note: For latest updates and additional info,

    please consult Central Technical Service


    Department for more details. Testing results
    and/or copies of Approval Documents for
    above - mentioned membranes are available
    upon request.

    05/15

    In cases of extreme absorbency, a priming


    coat of 50/50 WA98 adhesive and solvent may
    assist water shedding and absorption. However,
    a follow up of full strength adhesive for full

    You might also like