SJT SJM SJP Sales Presentation

SJT / SJM / SJP
Large Vertical Pumps
Sulzer Pumps
The Heart of Your Process
SJT, SJM, SJP

Sulzer Pumps
Product Overview
SJT Turbine
Ns 1800 < 5000
nq 35 < 110
SJM Mixed Flow

Ns 5800 < 8300
nq 113 < 161
Discharge head
with thrust
bearing assy.
SJP Axial Flow

Ns ~ 14,500
nq ~Large
280
Verticals presentation Copyright Sulzer Pumps> | slide 2
SJT, SJM, SJP

Sulzer Pumps
Applications
Large vertical pumps are "engineered-to-order" pumps for power and

water applications including, but not limited to the following:
cooling tower and cooling water circulation
waste or storm water sump drainage
water supply installations
booster service from open or closed systems
secondary recovery supply and injection systems
irrigation supply and land drainage
offshore fire and service water
flood control
Large Verticals presentation Copyright Sulzer Pumps> | slide 3
SJT, SJM, SJP

Sulzer Pumps
Example pump designations

SJT 30KNC-3s (from SPHO hydraulic)
SJT
30KNC
3s
Vertical Turbine Pump

Nominal diameter of bowl [in], Hydraulic
Number of stages (3)
SJM BSm 950/001-1s (from B-range hydraulic)

SJM
BSm
950
001
1s
Vertical Mixed Flow Pump

Pump type: B-Range, semi-open impeller
Nominal diameter of impeller [mm]
Hydraulic Code
SJP 48PO-1s (from SPHO hydraulic)

SJP
48PO
1s
Vertical Propeller Pump

Nominal diameter of bowl [in], Hydraulic
SJT, SJM, SJP

Sulzer Pumps
Materials of Construction
Component
Bowls / Bell
Impellers
I-1
S-1
Cast Iron
Carbon Steel
Alum. Bronze,
12% Chrome -or-
Alum. Bronze,
12% Chrome -or-
316 Aus (or EN
316 Aus (or EN equiv)
S-3
D-1
Ni. Resist
Duplex
316 Aus (or EN equiv.)
Duplex
equiv.)
Impeller Rings (when

applicable)
12% Chrome
12% Chrome
316 Aus (or EN equiv.)
Duplex
Shafts
12% Chrome
12% Chrome
12% Chrome
Nitronic 50 (or EN equiv.)
Bearing Bushings
Cutless Rubber
Cutless Rubber
Cutless Rubber
Cutless Rubber
(Bronze Backed)
(Bronze Backed)
(Stainless Backed)
(Phenolic Backed)
Carbon Steel
Carbon Steel
Carbon Steel
Duplex
Bolting
SJT Large Vertical Pump
Sulzer Pumps
Operating Limits: SJT

46 Sizes
(69 Hydraulic Combinations)..........> 20" (508 mm)
Capacity ...........................................Q = 1,600 to 180,000 US GPM (360 to 41,000 M3/Hr)
Head
up to H = 360 ft (110 M)
Max. Operating Pressures ..............125 up to 925 PSIg (8.6 to 63.8 Bar)

model specific, see ePM
Temperature..................................... 122F (50C)
Nominal Speeds ..............................320 RPM to 1800 RPM
Direction of Rotation ......................Counterclockwise or (Clockwise, "B"-range and
SJT 40CLC) as seen from drive end.
Sulzer Pumps
SJT Performance Range: 60 Hz
Sulzer Pumps
SJT Performance Range: 50 Hz
Sulzer Pumps
SJT sample
Performance Curve
Sulzer Pumps
SJT Design Features & Benefits: Bowl Assembly

Suction bells are cast construction with a tail
bearing (to minimize shaft deflection at lowest
impeller) and anti-vortex ribs on all sizes.
Bowls are cast construction which are flanged
and bolted together.
An integral wear surface is standard on bell
and bowls. Replaceable wear ring is offered as
an option.
An optional strainer restricts entry of foreign
objects into the bowl assembly.
Bearing bushings are located in the bowl assembly to provide rotor support.
Bearing bushings lubricated by the pumped liquid as standard. Oil or clean water
flush is also available.
Sulzer Pumps
SJT Design Features & Benefits: Bowl Assembly (cont.)

Most impellers are enclosed design and are cast
construction. Some SJT impellers are semi-open.
The impeller is mounted on the pump shaft with a
split axial retaining ring and key to allow easy
disassembly.
The impellers are dynamically balanced to reduce
vibration.
The SJT can be a multistage pump to the limits
defined in the documentation.
The pump shaft is tailor-made to the service needs
and sized individually for each installation; sized for
max. torque.
SJM Large Vertical Pump
Sulzer Pumps
Operating Limits: SJM

17 Sizes
(31 Hydraulic Combinations)..........> 24" (610 mm)
Capacity ...........................................Q = 11,000 to 220,000 US GPM (up to 47,700 M3/Hr)
Head
up to H = 160 ft (48.8 M)
Max. Operating Pressures ..............up to 260 PSIg (up to 17.9 Bar)

Temperature..................................... 122F (50C)
Direction of Rotation ......................Counterclockwise or- Clockwise (B-Range)
as seen from drive end.
Sulzer Pumps
SJM Performance Range: 60 Hz
Sulzer Pumps
SJM Performance Range: 50 Hz
Sulzer Pumps
SJM sample
Performance Curve
Sulzer Pumps
SJM Design Features & Benefits: Bowl Assembly

Suction bells are cast construction, offered with a
tail bearing (to minimize shaft deflection at lowest
impeller) and anti-vortex ribs on all sizes.
Bowls are cast construction which are flanged
and bolted together.
A replaceable case liner is offered as an option.
An optional strainer restricts entry of foreign
objects into the bowl assembly.
Bearing bushings are located in the bowl
assembly to provide rotor support.
Bearing bushings lubricated by the pumped liquid
as standard. Oil or clean water flush is also
available.
Sulzer Pumps
SJM Design Features & Benefits: Bowl Assembly (cont.)

Impellers are semi-open design and are
cast construction.
The impeller is mounted on the pump
shaft with a split axial retaining ring and
key to allow easy disassembly.
The impeller is dynamically balanced to
reduce vibration.
The SJM is typically offered as a single stage unit.
A two stage pump SJM is available for increased head
requirements (LS, MS & PS models only).
The pump shaft is tailor-made to the service needs and sized
individually for each installation; sized for max. torque.
SJP Large Vertical Pump
Sulzer Pumps
Operating Limits: SJP

8 Sizes
(8 Hydraulic Combinations)............> 24" (610 mm)
Capacity ...........................................Q = 11,000 to 220,000 US GPM (up to 47,700 M3/Hr)
Head .................................................up to H = 26 ft (8 M)
Max. Operating Pressures ..............up to 270 PSIg (up to 18.8 Bar)
Temperature..................................... 122F (50C)
Direction of Rotation ......................Counterclockwise as seen from drive end.
Sulzer Pumps
SJP Performance Range: 60 Hz
Sulzer Pumps
SJP Performance Range: 50 Hz
Sulzer Pumps
SJP sample
Performance Curve
SJP Large Vertical Pumps
Sulzer Pumps
SJP Design Features & Benefits: Bowl Assembly

The SJP is offered as a single stage unit only.
Suction bells are cast construction, offered with a
tail bearing (to minimize shaft deflection at impeller)
and anti-vortex ribs on all sizes.
Bowls are cast construction which are flanged and
bolted together
Fabricated bowl and suction bell construction
available.
A replaceable case liner is offered as an option in
the bowl to increase bowl life when abrasive fluids
are pumped. It also reduces maintenance cost.
An optional strainer restricts entry of foreign objects
into the bowl assembly.
Sulzer Pumps
SJP Design Features & Benefits: Bowl Assembly (cont.)

Bearing bushings are located in the bowl assembly to
provide rotor support.
Bearing bushings lubricated by the pumped liquid as
standard. Oil or clean water flush is also available.
Impellers are open design (propeller type) and are cast
construction.
The propeller is mounted on the pump shaft with a split
axial retaining ring and key to allow easy disassembly.
The propeller is dynamically balanced to reduce
vibration.
The pump shaft is tailor-made to the service needs and
sized individually for each installation; sized for max.
torque.
SJT, SJM, SJP

Sulzer Pumps
Design Features & Benefits: Column Assembly

Column pipes are fabricated, flanged and bolted
construction.
Column pipes are to be sized for a fluid velocity of 12.5
ft/sec (3.8 m/sec) at BEP flow rate. Higher velocities are also
possible upon request.
Each column joint has a bearing spider which houses the
replaceable bearing bushing:
- drop-in bearing spider 14" (DN 350)
- integral spider - 16"+ (DN 400+)
Line shafts are connected by a threaded coupling for shaft
diameters 2.69" (68 mm). For larger shaft sizes the
coupling will be a sleeve, split ring and key type.
SJT, SJM, SJP

Sulzer Pumps
Design Features & Benefits: Column Assembly (cont.)

Product lubricated column assemblies are offered as
standard.
Enclosed lineshaft is offered as an option.
Oil lubrication, grease packed or clean water
flush are all offered.
The enclosing tube will be threaded together or
flanged and held in tension by the tube tension nut.
The tube is put into tension by a tube nut located in
the stuffing box area of the discharge head. Proper
bearing spans are maintained.
A tube stabilizer will be supplied for every 30 ft
(9 meters) of column assembly.
The lineshaft will be sized to transmit the torque over
the entire range of operation.
SJT, SJM, SJP

Sulzer Pumps
Design Features & Benefits: Discharge Head

A fabricated discharge head is offered as
standard.
These heads are offered with f or plain end
connection. flanges will be ANSI (AWWA C207
Class D).
Each discharge head comes with segmented
bend delivery nozzle and integral driver stand to
support the driver.
Window size will be large enough to allow easy.
Access to removable packing/seal box and drive
coupling.
The discharge nozzle can be positioned either
above or below ground.
SJT, SJM & SJP

Sulzer Pumps
Shaft Sealing Methods

Product Lubrication
Packed stuffing box is provided for reliable sealing and
simple maintenance.
By-pass packing box is used for higher pressure
applications where some of the pressure in the stuffing
box is by-passed back into the sump.
Optional cartridge type mechanical seals are available.
Headshaft sleeve offered as standard with product
lubricated stuffing boxes.
Enclosed Lineshaft for oil lubrication or clean water flush
Shaft sealing is accomplished by packing below the tube
tension nut.
SJT, SJM & SJP

Thrust Bearing Location
Sulzer Pumps
ISO Pump Design: thrust bearing in pump

US Pump Design: thrust bearing in motor
(offered in pump as an option)
A separate fabricated driver stand is
supplied to accommodate the thrust
bearing when it is fitted in the pump.
SJT, SJM & SJP

Sulzer Pumps
Thrust Bearing Details (if supplied in pump)

VAL grease lubricated, angular contact bearing
VALS/VALR oil lubricated, spherical roller bearing
VALS for open sump application
VALR for suction barrel application
To be selected for L10 bearing life of:

- 25,000 hrs at BEP and
- 16,000 hrs at Min Flow
VALS/VALR are supplied with a
cooling coil. (fan cooled design
available upon request)
SJT, SJM & SJP

Sulzer Pumps
Driving Assembly
The driver and drive coupling for the large vertical pumps is one
of the following:
1)
vertical hollow shaft motor with a threaded drive

coupling; axial thrust is carried in this motor.
2)
Sulzer Pumps supplies the drive shaft and requires

a steady bushing. The lift setting is made via an
adjusting nut at the top of the motor.
vertical solid shaft motor with a flanged adjustable

coupling (rigid coupling) with or without a spacer; axial
thrust is carried in this motor.
The lift setting is made via an adjusting nut

which is part of the rigid coupling assembly.
SJT, SJM & SJP

Sulzer Pumps
Driving Assembly (cont.)

3) vertical solid shaft motor with a
flexible (disk type) coupling with or
without a spacer;
axial thrust is NOT carried in this motor.
Thrust bearing required in the pump.
The lift setting is made via an adjusting
nut which is part of the thrust bearing
assembly.

SJT SJM SJP Sales Presentation

Uploaded by

Copyright:

Available Formats

SJT SJM SJP Sales Presentation

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SJT SJM SJP Sales Presentation

Uploaded by

Copyright:

Available Formats

SJT / SJM / SJP

Large Vertical Pumps

The Heart of Your Process

SJT, SJM, SJP

SJM Mixed Flow

SJP Axial Flow

SJT, SJM, SJP

Large vertical pumps are "engineered-to-order" pumps for power and

Large Verticals presentation Copyright Sulzer Pumps> | slide 3

SJT, SJM, SJP

Example pump designations

Vertical Turbine Pump

SJM BSm 950/001-1s (from B-range hydraulic)

Vertical Mixed Flow Pump

SJP 48PO-1s (from SPHO hydraulic)

Vertical Propeller Pump

SJT, SJM, SJP

316 Aus (or EN

316 Aus (or EN equiv)

316 Aus (or EN equiv.)

Impeller Rings (when

316 Aus (or EN equiv.)

Nitronic 50 (or EN equiv.)

Large Verticals presentation Copyright Sulzer Pumps> | slide 5

SJT Large Vertical Pump

Operating Limits: SJT

Max. Operating Pressures ..............125 up to 925 PSIg (8.6 to 63.8 Bar)

Large Verticals presentation Copyright Sulzer Pumps> | slide 6

SJT Large Vertical Pump

SJT Performance Range: 60 Hz

Large Verticals presentation Copyright Sulzer Pumps> | slide 7

SJT Large Vertical Pump

SJT Performance Range: 50 Hz

Large Verticals presentation Copyright Sulzer Pumps> | slide 8

SJT Large Vertical Pump

Large Verticals presentation Copyright Sulzer Pumps> | slide 9

SJT Large Vertical Pump

SJT Design Features & Benefits: Bowl Assembly

SJT Large Vertical Pump

SJT Design Features & Benefits: Bowl Assembly (cont.)

Large Verticals presentation Copyright Sulzer Pumps> | slide 11

SJM Large Vertical Pump

Operating Limits: SJM

Max. Operating Pressures ..............up to 260 PSIg (up to 17.9 Bar)

Large Verticals presentation Copyright Sulzer Pumps> | slide 12

SJM Large Vertical Pump

SJM Performance Range: 60 Hz

Large Verticals presentation Copyright Sulzer Pumps> | slide 13

SJM Large Vertical Pump

SJM Performance Range: 50 Hz

Large Verticals presentation Copyright Sulzer Pumps> | slide 14

SJM Large Vertical Pump

Large Verticals presentation Copyright Sulzer Pumps> | slide 15

SJM Large Vertical Pump

SJM Design Features & Benefits: Bowl Assembly

SJM Large Vertical Pump

SJM Design Features & Benefits: Bowl Assembly (cont.)

Large Verticals presentation Copyright Sulzer Pumps> | slide 17

SJP Large Vertical Pump

Operating Limits: SJP