EDT-135

E1 and Data Tester

• Minimum training for
installation and commissioning
applications

• Robust and reliable,

low life-cycle cost

• All the tests needed to find

simple and complex faults

• Service application family

includes Frame Relay, GSM,
and special sub rates

Applications Functions
• Installing, commissioning and main- • E1 and n x 64k BERT with Autocon-
taining E1 circuits and multiplexers figure and G.821, G.826 and M.2100
• Commissioning and maintainng data- testing
com and V.24 modem circuits • Clear OK/Status Page
• Commissioning Frame Relay services • Multi-interface capability: V.24/RS232,
• Installing and maintaining GSM V.11/X.24, V.35, V.36/RS449, G.703
circuits (2048/704kbit/s), G.703 co-directional
• Frame Relay commissioning tools,
This powerful tester includes a full set of turn-up, PING and Fox
measurements to install, commission and • Multiplexer tests include MUX/
troubleshoot E1 and data circuits, along with DEMUX and A-D/D-A measurements
the services that run over them. • Special sub-rates (HCM, X.50, V.110)
Installation tests require basic out-of-service
Bit Error Rate (BER) testing to assess cabling Features such as Autoconfigure and the 'Big
integrity. OK' result screen make it easy to use with a
minimum of training.
Full commissioning requires extended BER
testing to international standards, as well as
stress testing and complete assessment of link Quality of Service can be measured with
performance with respect to error and alarm G.821, G.826 or M.2100. E1 signal quality
reporting. measurements include jitter, level and pulse
shape. Datacom interface control signals can
For successful maintenance, rapid identifica- be monitored and set.
tion of the current line status is critical to the
speedy resolution of problems.
V.24 modem tests include dial-up, auto-
answer, distortion measurement and BER.
Specific services (such as Frame Relay and
Other important features include round trip
GSM) have their own testing requirements,
delay measurements on E1 and datacom
and require a tailored solution to ensure satis-
circuits and E1 drop and insert.
factory operation.

Comprehensive service testing is possible

using dedicated options.
Easy to Use Software Option Download
The EDT-135 has been designed with the user in mind. As well The testing capability of the EDT-135 can be greatly extended
as being lightweight and comfortable to hold and carry, all by downloading a range of software options. Applicable options
testers feature large LCD screens with integral backlight for the include Signal Level Measurement, Pulse Shape Analysis, Jitter,
most demanding testing environments. If you wish to self-sup- Large Frequency Offset of Transmit Clock, Frame Relay, HCM,
port the tester, the integral two-position backstand/carry handle GSM, Enhanced Datacom Tests and Voice Channel Noise
can easily be folded out, and can also be configured to suspend Measurement.
the instrument for hands-free viewing.
Test results are displayed in a concise, graphical format with our
recognised 'Big OK' when no errors are present. Multiple Instrument Applications
language support is standard and comprehensive alarm and E1 Service Turn-up
error status LEDs give clear indication of problems, even from a
Availability and performance of an E1 link can be established
distance. And, as you'd expect, all results data can be stored for
using either an intrusive or a non-intrusive test. The EDT-135
later analysis or printed to an external printer with a single
can be connected via 75W/120W connectors using Hi-Z termi-
keypress.
nation or at a protected monitor point. A typical simple E1 test
will take no longer than 30 seconds, the OK screen quickly indi-
Autoconfigure cates when an E1 service is present and error-free.
G.826/M.2100 test sequences can then be run, and the results
The Autoconfigure feature greatly simplifies instrument set-up. displayed, stored and printed.
A test can be started on framed or unframed traffic using just 2
key-presses. For a framed signal, the instrument can determine
the framing type, timeslot allocation and test pattern type.

Gelbrich Synchronization
The patented Gelbrich Synchronization method enables
synchronization on a test pattern to be maintained and accurate
BER measurement to be made even in the presence of rapid
bursts of errors. It also enables differentiation to be made
between bit slips and bit errors.

Result Storage and Printing

The EDT-135 has 8 test memories for the storage of text and
histogram results, for viewing or printing at a later time.
Printing of results is supported through the serial port. A set- n x 64kbit/s Timeslot Analysis
up screen enables the instrument to be set up for a range of
printers. 64kbit/s timeslots are grouped within the E1 frame to give end-
customers intermediate data speeds such as 128 or 256kbit/s.
The EDT-135 can perform BER analysis on bundles of
Programmable Timers n x 64kbit/s slots, and drop and insertn x 64 kbit/s to an exter-
nal protocol analyser via V.11.
The instrument can be programmed to start a test at a specified
date and time for a selectable duration.

Remote Operation
The instrument is compatible with the DTM-32 remote opera-
tion solution.

Battery/Mains Operation
8-10 hour battery life using rechargeable and exchangeable bat-
teries. Long duration testing can be achieved with a.c. mains
power.
G.826 and M.2100 Analysis
G.826 is the ITU-T recommendation for error performance of
international digital paths at or above the Primary Rate. The
complementary M.21xx series permits rigorous testing of PDH
links but in shorter time periods. Both methods are included as
standard software modules in the EDT-135 tester. The follow-
ing screens illustrate the summary results from G.826 and
M.2100 tests.

Results Monitor

Error histograms can be indicated as a histogram on a scale of

up to 60 days.

A graphical display of past and present alarm occurrences and

error ratios for both near and far directions at the same time.

Histograms
Faults in an E1 line can be caused by low signal, pulse distortion
or jitter.

If loss of signal (LOS) or similar alarms are indicated by a net-

work element, level measurement and pulse shape tests can eas-
ily be made to determine where the fault exists in a link, by
examining the signal condition.

A low or distorted signal received by a network element would

indicate a problem with the preceding element or the intercon-
necting cables.

A set of histogram screens may be displayed, based on the

recorded history of alarms, errors and G.826/M.2100 events. Excessive jitter can result in bit errors, loss of frame synchro-
There are histograms for each valid alarm, error and nization or similar faults. Where these faults exist, jitter meas-
G.826/M.2100 result type (up to 12) at each resolution (days, urements can be performed to determine if jitter is the cause,
hours, minutes and seconds). and also to discover at which point in the system the jitter reach-
es unacceptable levels.

E1 Service Troubleshooting
An extended bit error test will determine whether a periodic
fault is causing problems. Electrical equipment such as air-
conditioning may cause problems at regular times in the day.
Error histograms make it possible to identify external events
which can be isolated as causes of the problem.
 Service Turn-up
HCM* Testing (HCM Option)
High Capacity Multiplexing (HCM) is a Newbridge proprietary
rate-adaption and sub-rate multiplexing scheme that provides a
If high jitter levels are isolated to the outputs of particular net- bandwidth granularity of 800bit/s throughout a network. HCM
work elements, these elements can be taken out of service and multiplexes multiple V.24 lines into a single G.703 timeslot with
further tested by injecting jitter at a known level and testing the very good bandwidth efficiency. The HCM option for the
jitter on the output (jitter transfer). EDT-135 enables users to verify correct configuration, the abil-
ity of the link to maintain synchronisation to communicate data
without errors.
Jitter testing, Level Measurement and Pulse Shape Analysis
options can be ordered for the EDT-135.
Various errors can be injected to simulate problems and test the
network response. These include bit errors, HCM FAS and
Primary Multiplexer Testing Signalling FAS errors, and HCM Frame and Signalling AIS
The 2Mbit/s Framed capability of the EDT-135, and its wide errors.
range of interfaces enable in-service and out-of-service testing
of a multiplexer to be carried out using a single instrument.
Testing is possible in the mux and demux directions. For *HCM is proprietary to Newbridge networks corporation.
example, testing of the customer-network (mux) direction is Used with permission.
performed by transmitting a test pattern into the multiplexer
customer-side at n x 64kbit/s via V.24, V.11, V.35, V.36, RS449 or
G.703 co-directional. The 2Mbit/s frame generated by the mul-
Frame Relay Testing (Frame Relay Option)
tiplexer is then monitored and the BER of the pattern in the Loaded into the EDT-135, the Frame Relay option provides
appropriate timeslot(s) is evaluated. three test modes suitable for installation and maintenance of
Frame Relay services:·
• Frame Relay service Turn-Up for verification of user-to-
network connectivity and configuration
• 'Fox' test for stress testing and Committed Information
Rate confirmation
• TCP/IP PING Request Testing, providing additional tests
to verify the connectivity of far-end terminals.
 Weight/Dimensions
Weight:
1.55kg approx
Dimensions (in mm):

Accessories
V.11 Cable Test Adapter
This accessory detects a number of common faults on V.11
cables, which due to the nature of balanced line interfaces would
otherwise go unnoticed.

ELM-2 Equalizer and Level Meter

The ELM-2 accessory allows the instrument to be connected to
2Mbit/s lines carrying hazardous voltages and Ö¦ distortion. It
removes the DC voltage, equalizes the signal and also measures
and displays the signal level.

PenBERT 2Mbit/s Monitor

The PenBERT PCM monitor can be used with the EDT-135 to
perform simple end-to-end tests on a 2Mbit/s line. Errors and
alarms are indicated by LEDs.

V Interface Troubleshooting (V Status Option)

The V Status option shows the status of input and output
circuits when testing V.24, V.35 and V.11 interfaces. It also offers
ON/OFF softkey control for a selection of the output circuits.

Equipment Cases
A range of equipment cases and shoulder-bags is available to
allow convenient transport and storage of the EDT-135 and
accessories.

DTM-32 Features
The DTM-32 product offers Remote Operation using an on-
screen faceplate, via an easy to use WindowsTM interface.
Technical Specifications
Generator/ Receiver Level and Frequency Stores/Memory
Interfaces: Digital generation/measurement of 8 test result memories and 8
G.703 sinusoidal signals in a timeslot. (A-law configuration stores
Outputs: coding to ITU-T Rec. G.711)
Balanced 3 pin CF connector Self Check
Unbalanced BNC connector X.50 Test Modes Comprehensive self check at power on
Interfaces:
G.703 Test Modes: V.11, V.35, V.36, RS449 and G.703 Languages
RX co-directional English, German, French, Spanish,
Framing: Italian, Turkish and Portuguese
PCM30, PCM30CRC, PCM31, Test Patterns
PCM31CRC, or Unframed PRBS: Power Supply
G.703 line code: 26-1, 29-1, 211-1, 215-1, External supply:
HDB3, AMI, co-directional Alternating 1 and 0s, All 1s, All 0s, External mains charger
V.11 drop: 8 and 16 bit programmable word Rechargeable batteries:
1 x 64kbit/s, n x 64kbit/s 8 to 10 hours operating time
Error Injection Battery low:
RX/TX Bit, Code, FAS, CRC errors: warning before auto switch off
As RX plus: Single, ratio or frequency
BER Test pattern generation:
Single timeslot Clocking
n x 64kbit/s timeslots G.703 transmit clock source
V.11 Drop/Insert: 2048kbit/s and co-dir:
Drop and/or Insert n x 64kbit/s Internal, External, From RX
timeslots
Drop and Insert 1 timeslot Error and Alarm Indication
Programmable Si, Sa, A and E bits and LEDs:
NMFAS 2 summary, 14 alarm/error, option,
low battery
Through Mode
As RX/TX plus Drop and/or Insert Printer and Remote Operation
via V.11 Interface:
V.24, DTE, Async
Round Trip Delay Baud rates:
Framed and Unframed 2Mbit/s 300, 600, 1200, 2400, 9600, 19200,
38400
MUX and DEMUX Testing
Receiver and transmitter as for RX/TX Front Panel
modeUnframed TX and RX on V inter- Display:
faces or G.703 co-directional 42 character x 16 line LCD, LED
back-light
Framed Monitor Keyboard:
Monitor and display of: Numerical keypad, 4 Cursor,
FAS, NFAS, MFAS, NMFAS, and 2 Contrast, Main Menu, 6 Softkeys,
CRC MFAS words 8-bit digital code Alt, On and Off
word in any selected timeslot, CAS
status of all 30 channels with
idle/busy indication
Ordering Information
EDT Platinum BN 4562/31
(M.2100, G.826, Extended PRBS,
Level Measurement Options)
EDT X.50 Sub-Rate BN 4562/32
(M.2100, G.826, Extended PRBS, X.50,
HCM, V.110 Options)
EDT Diamond BN 4562/33
(M.2100, G.826, Extended PRBS, Pulse Shape,
Level Measurement, Jitter Options)
EDT Frame Relay BN 4562/36
(M.2100, G.826, Extended PRBS,
Frame Relay, All 1s All 0s Options)
EDT Datacom BN 4562/37
(Includes all software options to
comprehensively address datacomms testing)
EDT Complete BN 4562/38
(Includes all software options)

Complete with :
a.c. adapter/charger. Select appropriate plug :
US, European, UK or Australian
Operating Manual
M.2100 Option BN 4562/00.13
G.826 Option BN 4562/00.34
Extended PRBS Option BN 4562/00.36

Accessories (available at extra cost):

External clock adapter K 1513
V.24 Download cable K 1515
Printer cable 25 way (M/F) K 1500
V.11 DCE adapter cable K 150
V.36/RS449 DTE adapter cable K 1506
V.36/RS449 DCE adapter cable K 1507
V.24/RS232 DCE adapter cable K 1512

V.35 adapter cables (jackscrew fixing)

V.35 DTE (AMP) 1.6 mm dia. pin male K 1508
V.35 DCE (AMP) 1.6 mm dia. pin female K 1509
V.35 DTE (Positronic) 1.6 mm dia. pin male K 1525
V.35 DCE (Positronic) 1.6 mm dia. pin female K 1526
V.35 adapter cables (clip fixing)
V.35 DTE (Positronic) 1.0 mm dia. pin male K 1510
V.35 DCE (Positronic) 1.0 mm dia. pin female K 1511

DTM-32 Remote Operation Software DTM32

Equipment case (small) BN 4562/00.50
Equipment case (large) BN 4562/00.51
Soft carrying case BN 4518/00.08
Soft shoulder bag BN 4562/00.01
Neck Strap BN 4562/00.53
V.11 cable Test Adapter BN 4534/00.37
ELM-2 Equalizer Level Meter BN 4546/01
PenBERT 2Mbit/s Monitor BN 4555/10
 Global Headquarters
20400 Observation Drive
Germantown, Maryland 20876-4023 USA
Options (available at extra cost): Toll Free 1-800-638-2049
Tel +1-301-353-1550
French S/C bits BN 4562/00.11 Fax +1-301-444-8468
GSM BN 4562/00.15 www.acterna.com
Large Frequency Offset BN 4562/00.19
All Ones/All Zeros Histogram BN 4562/00.20
Noise Measurement BN 4562/00.23
V Interface Status Monitor BN 4562/00.28 Regional Sales
V.110 BN 4562/00.32 Headquarters
HCM BN 4562/00.38
Frame Relay (Enhanced) BN 4562/00.41 North America
Jitter BN 4562/00.42 20400 Observation Drive
Germantown, Maryland 20876-4023
Datacom BN 4562/00.44 USA
V Delay BN 4562/00.48 Toll Free 1-800-638-2049
Level Measurement BN 4562/00.52 Tel +1-301-353-1550
Pulse Shape Analysis BN 4562/00.56 Fax +1-301-444-8468

Latin America
Av. Eng. Luis Carlos Berrini
936 8/9. Andar
04571-000 Sao Paulo, SP
Brazil
Tel +55 11 5503 3800
Fax +55 11 5505 1598

Asia/Pacific
42 Clarendon Street
PO Box 141
South Melbourne, Victoria 3205
Australia
Tel +61 3 9690 6700
Fax +61 3 9690 6750

Western Europe
Arbachtalstrasse 6
72800 Eningen u.A.

LL/PL/0061/0201/AE
Germany
Tel +49 7121 86 2222
Fax +49 7121 86 1222

Eastern Europe, Middle East & Africa

Elisabethstrasse 36
PO Box 13
2500 Baden
Austria
Tel +43 2252 85 521 0
Fax +43 2252 80 727

1st Neopalimovskiy Per. 15/7 (4th floor)

119121 Moscow
Russia
Tel +7 095 248 2508
Fax +7 095 248 4189

Acterna is present in more than

80 countries. To find your local sales
office, go to www.acterna.com

Note: Specifications, terms, and conditions are subject to change without notice.
© Copyright 2001 Acterna, LLC. All rights reserved. Acterna, The Keepers of Communications, and its logo are trademarks of
Acterna, LLC. All other trademarks and registered trademarks are the property of their respective owners.

TTC AND WWG ARE NOW ACTERNA. TO LEARN MORE, VISIT WWW.ACTERNA.COM