DC Fans-Specials 2014 11 en

Information
DC axial fans
DC fans - specials
161
Representatives
Accessories
AC centrifugal fans
AC axial fans
ACmaxx / GreenTech
EC-Compact fans
DC fans - specials
DC centrifugal fans
164
168
173
177
2014-11
Speed signal
Alarm signal
Vario-Pro / Speed setting / Control input
Protection against ambient influences, Protection class IP 54 / IP 68
DC fans - specials
Technical information
Cooling capacity and efficiency

Greater power density, increasing miniaturisation and extreme electronic
component density are posing increased demands on the cooling capacity
and efficiency of fans. The intelligent and space-saving integration of the
fan in the device configuration is therefore of major importance:
Tailor-made cooling adapted to the situation as and when required.
Programmable cooling by defining speed profiles.
Transparency of function thanks to complete, interactive monitoring in
all operating conditions.
Standard fans in electronics cooling have proven themselves millions of

times.
With a constant speed and a correspondingly high noise level, they continuously provide the air flow needed for extreme cases. These extreme
situations, however, occur extremely rarely, if at all, during the operating
period. An intelligent fan is needed, which adapts automatically to the
currently required level of cooling.
2014-11
ebm-papst provides intelligent cooling concepts which are optimally

adapted to requirements. For example:
162
1. Speed adjustment via temperature sensor

ebm-papst answers with a complete range of DC fans with temperaturecontrolled speed adjustment via a temperature sensor, available in a
variety of standard dimensions.
Installation is very simple. The control electronics receive thermal
information for the speed adjustment continuously and without losses,
either externally via a freely designed and positionable strand, or
internally directly in the fan hub in the air flow. A range of temperature
sensors can be found on page 174.
2. DC fans with separate control input

Open or closed-loop speed control is also possible with DC fans that have
a separate control input. A variation in speed can thus be implemented via
a control voltage or a pulse-width modulated signal. These possibilities
are used primarily in devices that have appropriate standard interfaces
and thus require a load-dependent variation of the fans.
Information
DC centrifugal fans
DC axial fans
DC fans - specials
ACmaxx / GreenTech
EC-Compact fans
AC axial fans
AC centrifugal fans
7. Protection against environmental influences

Some applications place particular demands on the fans resistance to
ambient influences, such as dust, moisture, water and salt. ebm-papst
offer solutions for adapting fans to these ambient conditions.
Accessories
5. Turbo drives
Fans with three-phase EC drives and microprocessor-controlled motor
electronics. These three-phase motors whose torque is virtually nonreliant on the rotor position are used for extremely high running smoothness. The speed of these fans can be controlled over a very wide range
with PWM, analogue voltage or temperature. Optionally, the fans can be
supplied with reversible direction of rotation and active brake operation.
The successful concept of Vario-Pro is: Tailor-made software instead of

fixed hardware, because programmed software modules for motor control
and application intelligence are responsible for the work that analogue
components were responsible for in the past. This central control unit of
the Vario-Pro comprises a microcontroller and an EEPROM, on which all
characteristics are stored.
163
Representatives
4. Alarm signal
For applications which require monitored fan operation with alarm
signal, ebm-papst has numerous alarm signal versions, either a static,
pre-processed or interface-compatible high or low continuous signal
depending on the type of fan.
6. Vario-Pro fans
This high-end fan concept by ebmpapst with programmed intelligence
and customer-specific integrated functions makes your electronics
cooling even more versatile and competitive. Vario-Pro ensures a fresh
economic breeze for all demanding cooling tasks e.g. where greater
reliability, more flexibility and intelligent function features such as alarm
function, speed control etc. are required.
2014-11
3. Speed signal
DC fans with speed signal.
The integrated electronic tachometer continuously provides an actual
speed signal for external evaluation. The user is informed at all times of
the current fan speed via an extremely simple signal evaluation on the
customer side. The speed signal is via a separate lead.
DC fans - specials
Technical information
Speed signal /2
mA
VDC
mA VDC
mA
0,4
30
30
31
400 F
0,4
30
30
32
400
0,4
30
30
33
420 J
0,4
15
15
34
500 F
0,4
30
30
35
600 F
0,4
30
30
36
620
0,4
30
30
37
630 U
0,4
30
30
38
600 N
0,4
28
28
39
600 J
0,4
30
30
41
700 F
0,4
30
30
42
8450
0,4
28
28
43
8400 N
0,4
28
28
44
8400 N VARIOFAN
0,4
30
30
45
8300
0,4
30
30
46
8200 J
0,4
30
30
47
3400 N
0,4
28
28
48
3400 N VARIOFAN
0,4
30
30
49
3300
0,4
30
30
50
3300 N
0,4
30
30
51
3212 J / 3214 J
0,4
30
30
52
Alle TD Lfter. Bsp.: 6400 TD
2014-11
Page
3218 J
0,4
60
60
52
3250 J
0,4
60
60
53
4412 F / 4414 F
0,4
30
30
54
4418 F
0,4
60
60
54
4400 FN
0,4
30
30
55
4312 / 4314
0,4
30
30
56
4318
0,4
60
60
56
4312 / 4314 VARIOFAN 0,4
30
30
57
4318 VARIOFAN
0,4
60
60
57
4400
0,4
30
30
2 58/59
4100 N
0,4
30
30
60
4100 NHH...NH6
0,4
60
60
10
61
4100 NH7...NH8
0,4
60
60
20
62
DV 4100
0,4
30
30
63
Subject to alternations
164
Fan description
Basic type
Condition: Isource
All voltages measured to ground.

External load resistor Ra / US / UBS required.
Pulses per revolution
Speed signal
US High
VDC
Signal data
Sensor operating
voltage UBS max.
Condition: Isink
Type
250
Electrical connection
Ra
Perm. sink current

Isink max.
Speed-proportional rectangular pulse for external speed monitoring of fan motor

2, 3 or 6 pulses per revolution
Open collector signal output
Extremely wide operating voltage range
Easy adaptation to user interface
Connection via separate lead
The sensor signal also serves as a major comparison variable for setting and
maintaining the setpoint speed for interactive or controlled cooling with one or
several interconnected fans.
Speed signal
US Low
Information
Condition: Isource
Sensor operating
voltage UBS max.
Perm. sink current

Isink max.
mA
VDC
mA
VDC
mA
0,4
30
30
64
DV 5200
0,4
30
30
65
5112 N
0,4
15
20
66
5114 N / 5118 N
0,4
60
60
20
66
5300
0,4
72
72
67
5300 TD
0,4
72
72
20
68
7112 N / 7118 N
0,4
60
60
20
69
7114 N
0,4
30
30
20
69
7200 N
0,4
15
15
20
70
6300
0,4
72
72
20
72
6300 TD
0,4
72
72
20
73/74
6300 N
0,4
72
72
20
74 a
DV 6300
0,4
72
72
20
75
6400
0,4
60
60
20
76
2200 FTD
0,4
72
72
20
80
RL 48
0,4
30
30
95
RL 65
0,4
30
30
96
RL 90 N
0,4
30
30
97
RLF 100
0,4
30
30
98
RG 90 N
0,4
30
30
99
RG 125 N
0,4
30
30
100
RG 160 N
0,4
30
30
20
101
RG 160 NTD
0,4
60
60
20
102
RG 190 TD
0,4
72
72
20
103
RG 220 TD
0,4
72
72
20
104
RG 225 TD
0,4
72
72
20
105
RET 97 TD
0,4
72
72
20
106
REF 100
0,4
30
30
107
RER 120 TD
0,4
72
72
20
109
RER 133 TD
0,4
72
72
20
113
RER 160 NTD
0,4
60
60
20
115
REF 175 TD
0,4
72
72
20
116
RER 175 TD
0,4
72
72
20
117
RER 190 TD
0,4
72
72
20
118
RER 220 TD
0,4
72
72
20
124
RER 225 TD
0,4
72
72
20
125
Accessories
AC centrifugal fans
AC axial fans
ACmaxx / GreenTech
EC-Compact fans
DC fans - specials
Page
Note:
With these fan options, deviations in regard to temperature range, voltage
range and power consumption are possible compared with standard fan
data.
165
2014-11
DC centrifugal fans
Speed signal
US High
VDC
Representatives
Condition: Isink
Type
5200 N
Signal data
Fan description
Basic type
Speed signal
US Low
Pulses per revolution
DC axial fans
Available on request:
Electrically isolated sensor and signal circuit
Varying voltage potentials for power and logic circuit
Speed signal /12
Speed-proportional rectangular pulse for external speed monitoring of fan motor

2, 3 or 6 pulses per revolution
TTL-compatible
Integrated pull-up resistor
Connection via separate lead
The sensor signal also serves as a major comparison variable for setting and maintaining
the setpoint speed for interactive or controlled cooling with one or more interconnected
fans.
Perm. sink current

Isink max.
Fan description
Basic type
mA
Page
2,55,5
39
2,55,5
39
0,4
2,55,5
44
4412 F/12 GM
0,4
2,55,5
54
4418 F/12
0,4
2,55,5
54
4312 /12 M
0,4
2,55,5
56
4314 /12
0,4
2,55,5
56
4182 N/12 X
0,4
2,55,5
60
Type
VDC
mA
614 N/12 GM
0,4
618 N/12 N
0,4
8412 N/12 H
Speed signal
US High
mA
Condition: Isink
VDC
Signal data
Speed signal
US Low
Condition: Isource
Note:
With these fan options, deviations in regard to temperature range, voltage range
and power consumption are possible compared with standard fan data.
2014-11
Alle TD Lfter. Bsp.: 6400 TD
166
Information
1
20
70
0,4
2,55,5
20
76
DV 6424/12
0,4
4,55,25
12
78
DV 6448/12
0,4
4,55,25
12
78
RG 125-19/12 N/12
0,4
2,55,5
100
RG 160-28/12 N/12
0,4
2,55,5
101
RG 160-28/18 N/12
0,4
2,55,5
20
101
RER 125-19/12 N/12 0,4
2,55,5
112
RER 160-28/12 N/12 0,4
2,55,5
114
RER 160-28/18 N/12 0,4
2,55,5
20
114
Speed signal
US Low
0,4
6424/12 H
DC centrifugal fans
2,55,5
7214 N/12
DC fans - specials
mA
ACmaxx / GreenTech
EC-Compact fans
Page
VDC
AC axial fans
Fan description
Basic type
mA
Type
167
2014-11
Accessories
AC centrifugal fans
Note:
With these fan options, deviations in regard to temperature range, voltage
range and power consumption are possible compared with standard fan data.
Representatives
Perm. sink current

Isink max.
mA
Signal data
Speed signal
US High
VDC
Condition: Isink
Condition: Isource
DC axial fans
Electrically isolated sensor and signal circuit
Varying voltage potentials for power and logic circuit
Alarm signal /17
60
20
15
1500 100
46
60
n > nG
60
20
15
1500 100
46
60
n > nG
60
20
15
1500 100
50
n < nG
60
n > nG
60
20
15
850 100
56
n < nG
60
n > nG
60
20
15
1500 100
60
0,4
n < nG
3314 /17
0,4
n < nG
4318 /17
0,4
4184 N /17 X
0,4
0,4
8318 /17 H
Condition:
60
Alarm output
voltage UA Low
8318 /17
Note:
With these fan specials, deviations as regards temperature range,
voltage range and power consumption are possible compared with standard fans.
Ra
2014-11

External load resistor Ra from UA to UBA required.
168
t 2 = Alarm signal suppression during start-up

* n < speed limit nG by braking or locking.
Fan description
Basic type
Alarm delay
time t2
n > nG
n < nG
VDC
Speed limit nG
Max. permissible
Sink current
VDC
Type
Condition:
Alarm operatingvoltage UBA max.
mA
mA
Alarm
signal data
Condition:
VDC
Alarm outputvoltage UA High
mA
Condition:
Isink =
Condition:
Isource
Alarm signal for speed monitoring

Signal output via open collector
The fan emits a high continuous signal during trouble-free operation within the permissible
voltage range.
Low signal when speed limit is not reached
After elimination of fault, the fan returns to its setpoint speed;
the alarm signal reverts to high.
RPM
Page
Information
1500 100
57
60
n > nG
60
20
15
1500 100
57
60
n > nG
60
20
15
1150 100
57
n < nG
60
n > nG
60
20
15
850 100
57
n < nG
60
n > nG
60
15
15
1330 60
70
0,4
n < nG
4318/17 T
VARIOFAN
0,4
7214 N/17
0,4
* After switching on UB
AC axial fans
4314/17 T
VARIOFAN
169
2014-11
Accessories
AC centrifugal fans
Note:
Representatives
Condition:
n < nG
Alarm output
voltage UA Low
0,4
4312/17 T
VARIOFAN
DC centrifugal fans
15
Page
DC fans - specials
20
RPM
ACmaxx / GreenTech
EC-Compact fans
Alarm delay
time t2
60
60
0,4
Fan description
Basic type
Max. permissible
Sink current
4312/17 MT
VARIOFAN
Speed limit nG
n > nG
n < nG
VDC
Condition:
Condition:
Isource
VDC
Type
Condition:
mA
VDC
Condition:
Isink =
mA
mA
Alarm
signal data
DC axial fans
With integrated signal latching for subsequent recognition of short-time faults
Alarm circuit open collector or TTL
Electrically isolated for maximum device safety
Defects in the power circuit do not affect the alarm circuit.
Alarm signal /19
60
20
15
1500 100
46
n < nG
60
20
15
1500 100
56
60
n < nG
60
10
10 4
1800 20
70
28
n < nG
28
10
10 4
1900 100
98
28
n < nG
28
10
10 4
1900 100
108
n < nG
0,4
n > nG
60
7214 N/19
0,4
n > nG
RLF 100-11/14/19
0,4
n > nG
RER 101-36/18N/19 HH
0,4
n > nG
0,4
4312/19
Condition:
60
8314/19 H
Condition:
Alarm output
voltage UA Low
n > nG
VDC
Note:
With integrated signal latching for subsequent recognition of short-term faults.
Alarm circuit open collector or TTL.
Electrically isolated for max. device safety; defects in power circuit have no effect on the alarm circuit.
Ra

2014-11
RPM
Page
170
Fan description
Basic type
Alarm delay
time t2
VDC
Type
Speed limit nG
Max. permissible
Sink current
mA
mA
Alarm
signal data
Condition:
VDC
mA
Condition:
Isink =
Condition:
Isource

The fan emits a low continuous signal during trouble-free operation within the permissible
voltage range.
High signal when speed limit is not reached
After elimination of fault, the fan returns to its setpoint speed; the alarm signal
reverts to low.
t 2 = Alarm signal suppression during start-up.

* n < Speed limit nG by braking or locking.
Information
Alarm signal /37

Go / No-go alarm
DC axial fans
DC centrifugal fans
n > nG
28
10
<1
45
n > nG
28
10
<1
49
RPM
DC fans - specials
28
Fan description
Basic type
mA
Speed limit nG
n nG
VDC
Condition:
28
mA
Alarm delay
time t2
Max. permissible
Sink current
Page
ACmaxx / GreenTech
EC-Compact fans
0,4
n nG
3412 N/37 GV
VDC
Condition:
Isource
0,4
mA
Condition:
8412 N/37 GMLV
VDC
Condition:
Isink =
Type
Condition:
Alarm
signal data
Alarm output
voltage UA Low

The fan emits a high continuous signal during trouble-free operation within the
permissible voltage range.
Low signal when speed limit is not reached
After elimination of fault, the fan returns to its setpoint speed; the alarm signal
reverts to high.
AC axial fans
Note:
Alarm circuit TTL compatible.
AC centrifugal fans
Accessories
Ra
171
Representatives
t 2 = Alarm signal suppression during start-up.

* n < Speed limit nG by braking or locking.
2014-11

Alarm signal /39

Go / No-go alarm
28
10
<1
33
n = nG
28
10
<1
36
28
n = nG
28
10
<1
39
28
n = nG
28
10
<1
*
*
*
39
28
n = nG
28
10
<1
48
28
n = nG
28
10
<1
48
n > nG
28
n = nG
28
10
<1
54
n > nG
28
n = nG
28
10
<1
54
0,5
n > nG
28
n = nG
28
10
<1
54
0,4
n > nG
30
n = nG
30
<1
*
*
*
*
*
*
55
0,5
n > nG
28
614 N/39 M
0,5
n > nG
618 N/39 N
0,5
n > nG
3412 N/39 H
0,5
n > nG
3414 N/39 HH
0,5
n > nG
4412 F/39 GL
0,5
4412 F/39 M
0,5
4414 F/39
4414 FN/39 H
612 F/39 H
Condition:
n = nG
0,5
Condition:
28
Alarm output
voltage UA Low
412/39
Note:
Ra
All voltages measured to ground

2014-11
RPM
Page
172
Fan description
Basic type
n > nG
VDC
Speed limit nG
VDC
Type
Condition:
Max. permissible
Sink current
mA
mA
Alarm
signal data
Alarm delay
time t2
VDC
mA
Condition:
Isink =
Condition:
Isource

The fan emits a low continuous signal during trouble-free operation within the permissible
voltage range.
High signal when speed limit is not reached
After elimination of fault, the fan returns to its setpoint speed;
the alarm signal reverts to low.
t 2 = Alarm signal suppression during start-up

* n < Speed limit nG by braking or locking
Information
Vario-Pro
DC centrifugal fans
DC axial fans
Software instead of hardware aptly describes the unique fan concept,

equipped at the plant with tailor-made intelligence for cooling electronics.
Flexible configuration using software, allows quicker availability, sampling from
the factory and the ability to supply customer-specific solutions in any quantity.
Alarm and tachometer functions

Optional alarm and/or tachometer function
Selectable alarm speed limit (with
hysteresis) and alarm delay time
Latching of alarm signal
Delay only when starting or permanently
active
High or Low output signal in case of
alarm
Optional alarm if temperature sensor fails
Optional alarm in case of excess
temperature
Motor management
High control accuracy due to digital
motor management
Higher operating efficiency due to
optimum adaptation of motor hardware
and software
Fan series
Page
Fan series
Page
Fan series
620
37
4100 NH...NH6
61
DV 6300
75
8400 N
44
4100 NH 7-8
62
6400
76
8300
46
DV 4100
63
DV 6400
78
8200 J
47
5200 N
64
RL 90 N
97
3400 N
48
DV 5200
65
RLF 100
98
3300
50
5100 N
66
RG 90 N
99
3300 N
51
5300
67
RG 125 N
100
3200 J
52
7100 N
69
RG 160 N
101
3250 J
53
7200 N
70
REF 100
107
4400 FN
55
6100 N
71
RER 101
108
4300
56
6300
72
RER 125 N
112
4100 N
60
6300 N
74 a
RER 160 N
114
ACmaxx / GreenTech
EC-Compact fans
External Speed setting

Speed setting via temperature, PWM or
analogue control voltage
See page 174 (Speed setting)
Description of speed curve with up to
14 selectable interpolation points
Linear interpolation between the points
Zero speed possible
Recognition of sensor failure: In case of
loss of sensor, the fan operates at
programmable (fail-safe) speed.
DC fans - specials
Vario-Pro-Features
Representatives
173
2014-11
Accessories
AC centrifugal fans
AC axial fans
Page
Speed setting via

temperature sensor
The control variable is a temperature sensor which is either integrated into the fan or
connected to an additional control wire.
External temperature sensor Type T
Internal temperature sensor Type I
Ext. NTC type LZ370 (p. 253) is required

(to be ordered seperatly)
NTC integrated into the fan hub
Standard speed-temperature curve

for type T and type I
Optionally available with customer specific

temperature-speed control curve
n max
n max
n min
n min
30C
2014-11
nmin 1/2 nmax

Tmin 30 C; Tmax = 50 C
174
50C
T min
T max
nmin 800 1/min nmax model-dependent

Tmin 5 C
Tmax 85 C, model-dependent
Information
Speed setting with

control voltage or PWM
Speed setting via PWM Type P
Standard control range 0 ... 10 V
Standard PWM signal in two versions

a) PWM frequency, mainly 1 10 kHz (0100%),
Open collector input
b) Four-wire interface in accordance with Intel specifications
for 12 VDC fans, PWM frequency 25 kHz, incl. speed signal /2
DC fans - specials
Speed setting via control voltage Type A
DC centrifugal fans
DC axial fans
The control variable is a PWM signal or analogue control voltage.
ACmaxx / GreenTech
EC-Compact fans
R1
R2
Typical input resistance >10 k
AC axial fans
Optional with potentiometer
R1
AC centrifugal fans
R2
Internal reference = +5V

R1 typical 4.7...10 k
R2 typical 100 k
175
Representatives
Accessories
Optionally available with customer specific

P / A speed control curve
2014-11
Standard curve P / A
Speed setting via

multi-option control input
Customer can operate input either with PWM signal, analogue voltage, external temperature
control module or resistor.
The control signal-speed characteristics of the fan differ from the standard curve of the
A and P inputs (see p. 175).
To set up maximum speed, the control wire must be connected to UB.
The control input is usually combined with an open collector tachometer
(Type /2, see page 164).
Speed setting via multi-option control input

Notes on various control possibilities and their applications
Maximum ripple
3.5%
red
33 K
4,7 K
Lin/PWM control input

0-10 VDC / PWM
violet
Counter
Controller
U
PWM
Tach output
pulses per revolution
Isink max. 10 mA
white
10 K
Alarm
12 V
Temperature
control module
Speed setting
Speed setting
with
potentiometer
PWM 1 - 10 kHz
50002-1-0174
50003-1-0174
Speed display
12 V
Full speed
GND
blue
Speed setting
1 V - 10 V
100% PWM -> n=max

approx. 10% PWM -> n= min
< 10% PWM -> n=0
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
start up at > 14 %
start up at > 1.4 V
Customer circuit
Connection
GND
Tacho
0-10 V
PWM
Line 1
red
blue
white
violet
Line
Connection Colour Assignment / function
Line
Connection Colour Assignment / function
red
Maximum ripple 3.5 %
Tach
GND
blue
GND
white
2014-11
0-10 V / PWM violet
176
Tach output:
3 pulses / revolution
Control input (Impedance 100 k)
Fan
Information
Protected fans
against environmental influences
DC centrifugal fans
DC axial fans
Capable to fulfil special requirements for a broad range of applications

Resistant to environmental influences, such as dust, splash water, humidity, spray water and
salt fog
Highly competent solutions for adapting fans to environmental conditions
DC fans - specials
Stainless steel bearings

Special bearings made of stainless steel provide additional protection.
ACmaxx / GreenTech
EC-Compact fans
Type of protection: IP 54 / IP 68
In the type of protection IP 54, the motor and circuit boards are coated
and therefore protected against spray water and moisture.
The type of protection IP 68 is important for ebm-papst products, as it
ensures a high degree of protection for the encapsulated motor and
electronic against foreign bodies and water, whilst protecting the user
against potential hazards upon contact. Types of protection higher than
IP 68 are possible upon request.
Salt fog protection

Salt fog is extremely demanding on the resistance of the product.
ebm-papst makes use of technologies that protect fans and blowers
from salt fog reliably and durably.
Type of protection IP code

Protection against foreign bodies and accidental contact (first digit)
AC axial fans
The available solutions could be different depending on the fan size. We would be glad to
develop solutions tailored to the demands of your application.
1 Protection against foreign bodies > 50 mm (back of the hand)
Protection against dripping water or condensation
2 Protection against foreign bodies > 12 mm (finger)
Protection against dripping water, fans tilted 15 from vertical
3 Protection against foreign bodies > 2,5 mm (tool)
Protection against water spray up to 60 from vertical
4 Protection against foreign bodies > 1 mm (wire)
Protection against water spray from all sides
5 Protection against dust in harmful quantities
Protection against low-pressure water jets
6 Dust-proof
Protection against high-pressure water jets
Protection against temporary submersion (15 cm - 1 m)
Protection against continuous submersion
Accessories
No protection
177
2014-11
AC centrifugal fans
Water protection (second digit)
X No protection
Representatives
Moisture protection
Coated motor and printed circuit board protects against humidity and
condensation.
2014-11
178

DC Fans-Specials 2014 11 en

Uploaded by

Copyright:

Available Formats

DC Fans-Specials 2014 11 en

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DC Fans-Specials 2014 11 en

Uploaded by

Copyright:

Available Formats

Information

Cooling capacity and efficiency

Standard fans in electronics cooling have proven themselves millions of

ebm-papst provides intelligent cooling concepts which are optimally

1. Speed adjustment via temperature sensor

2. DC fans with separate control input

7. Protection against environmental influences

The successful concept of Vario-Pro is: Tailor-made software instead of

Alle TD Lfter. Bsp.: 6400 TD

4312 / 4314 VARIOFAN 0,4

All voltages measured to ground.

Pulses per revolution

Perm. sink current

Speed-proportional rectangular pulse for external speed monitoring of fan motor

Perm. sink current

RER 160 NTD

Pulses per revolution

Speed signal /12

Speed-proportional rectangular pulse for external speed monitoring of fan motor

Perm. sink current

All voltages measured to ground.

Alle TD Lfter. Bsp.: 6400 TD

RER 125-19/12 N/12 0,4

RER 160-28/12 N/12 0,4

RER 160-28/18 N/12 0,4

Perm. sink current

Alarm signal /17

All voltages measured to ground.

t 2 = Alarm signal suppression during start-up

Alarm operatingvoltage UBA max.

Alarm outputvoltage UA High

Alarm signal for speed monitoring

Alarm operatingvoltage UBA max.

Alarm outputvoltage UA High

Alarm signal /19

All voltages measured to ground.

Alarm operatingvoltage UBA max.

Alarm outputvoltage UA High

Alarm signal for speed monitoring

t 2 = Alarm signal suppression during start-up.

Alarm signal /37

Alarm operatingvoltage UBA max.

8412 N/37 GMLV

Alarm outputvoltage UA High

Alarm signal for speed monitoring

t 2 = Alarm signal suppression during start-up.

All voltages measured to ground.

Alarm signal /39

All voltages measured to ground

Alarm operatingvoltage UBA max.

Alarm outputvoltage UA High

Alarm signal for speed monitoring

t 2 = Alarm signal suppression during start-up

Software instead of hardware aptly describes the unique fan concept,

Alarm and tachometer functions

External Speed setting

Speed setting via

External temperature sensor Type T

Internal temperature sensor Type I