T-1 ETS-2288 FWT Data Service User Manual

HUAWEI
HUAWEI T-1 ETS-2288 Fixed

Wireless Terminal Data Service
User Manual
V200R002
Wireless Terminal Data Service
User Manual
Manual Version T2-030177-20050112-C-2.20

Product Version V200R002
BOM 31015077
Huawei Technologies Co., Ltd. provides customers with

comprehensive technical support and service. Please feel free to
contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co., Ltd.,
Bantian, Longgang District, Shenzhen, P. R. China
Postal Code: 518129
Website: http://www.huawei.com
Email: [email protected]
Copyright © 2005 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Huawei Technologies
Co., Ltd.
Trademarks
, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess,

ETS, DMC, TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium,
M900/M1800, TELESIGHT, Quidview, Musa, Airbridge, Tellwin,
Inmedia, VRP, DOPRA, iTELLIN, HUAWEI OptiX, C&C08 iNET,
NETENGINE, OptiX, iSite, U-SYS, iMUSE, OpenEye, Lansway,
SmartAX, infoX, TopEng are trademarks of Huawei Technologies Co.,
Ltd.
All other trademarks mentioned in this manual are the property of their
respective holders.
Notice
The information in this manual is subject to change without notice.

Every effort has been made in the preparation of this manual to ensure
accuracy of the contents, but all statements, information, and
recommendations in this manual do not constitute the warranty of any
kind, express or implied.
About This Manual
Release Notes
The product version that corresponds to the manual is HUAWEI T-1

ETS-2288 Fixed Wireless Terminal V200R002.
Related Manuals
The following manuals provide more information about the HUAWEI

T-1 ETS-2288 Fixed Wireless Terminal V200R002.
Manual Content
HUAWEI T-1 ETS-2288 It provides information for the terminal installation,
Fixed Wireless Terminal operation, usage and maintenance of HUAWEI T-1
User Manual ETS-2288 FWT.
HUAWEI T-1 ETS-2288
It is used for assisting the users in performing data
Fixed Wireless Terminal
services of HUAWEI T-1 ETS-2288 Fixed Wireless
Data Service User
Terminal. (Delivered with a CD-ROM)
Manual
Organization
HUAWEI T-1 ETS-2288 Fixed Wireless Terminal Data Service User

Manual introduces how to perform the data service of HUAWEI T-1
ETS-2288 Fixed Wireless Terminal (hereinafter referred to as FWT).
Chapter 1 Modem describes the modem integrated with FWT.

Chapter 2 Configuration Requirements lists the minimum system
requirements of the PC for conducting data service.
Chapter 3 Wireless Data Service elaborates the operation of data

service in Windows 98, Windows 2000 and Windows XP respectively,
including driver installation, dial-up and PC fax service, etc.
Chapter 4 Precautions describes the precautions of data service

conduct.
Chapter 5 Troubleshooting introduces common faults and handling

methods.
Intended Audience
The manual is intended for the user who owns the FWT Data Kit.
Conventions
The manual uses the following conventions:
I. General conventions
Convention Description
Arial Normal paragraphs are in Arial.
Warnings, Cautions, Notes and Tips are in Arial
Arial Narrow
Narrow.
Boldface Headings are in Boldface.
Courier New Terminal Display is in Courier New.
II. GUI conventions
Convention Description
Button names are inside angle brackets. For example,

<>
click the <OK> button.
Window names, menu items, data table and field
[] names are inside square brackets. For example, pop
up the [New User] window.
Multi-level menus are separated by forward slashes.
/
For example, [File/Create/Folder].
III. Keyboard operation
Format Description
Press the key with the key name inside angle
<Key> brackets. For example, <Enter>, <Tab>,
<Backspace>, or <A>.
Press the keys concurrently. For example,
<Key1+Key2> <Ctrl+Alt+A> means the three keys should be
pressed concurrently.
Press the keys in turn. For example, <Alt, A> means
<Key1, Key2>
the two keys should be pressed in turn.
IV. Mouse operation
Action Description
Press the left button or right button quickly (left button
Click
by default).
Double Click Press the left button twice continuously and quickly.
Action Description
Press and hold the left button and drag it to a certain
Drag
position.
V. Symbols
Eye-catching symbols are also used in this manual to highlight the

points worthy of special attention during the operation. They are
defined as follows:
Caution, Warning, Danger: Means reader be extremely careful

during the operation.
Note, Comment, Tip, Knowhow, Thought: Means a

complementary description.
Environmental Protection
This product has been designed to comply with the requirements on

environmental protection. For the proper storage, use and disposal of
this product, national laws and regulations must be observed.
User Manual
Wireless Terminal Data Service Table of Contents
Table of Contents
Chapter 1 Modem...........................................................................1-1
Chapter 2 Configuration Requirements ......................................2-1
Chapter 3 Wireless Data Service..................................................3-1

3.1 Install HUAWEI WIRELESS MODEM Driver .....................3-1
3.1.1 Install Windows 98 system Driver ...........................3-1
3.1.2 Install Windows 2000 system Driver .......................3-7
3.1.3 Install Windows XP system Driver.........................3-15
3.2 Data Service Reference ...................................................3-26
3.2.1 High-speed Packet Data Access...........................3-27
3.2.2 Low-speed Data Service Access...........................3-48
3.2.3 PC Fax Service......................................................3-48
Chapter 4 Precautions...................................................................4-1
Chapter 5 Troubleshooting...........................................................5-1
i
User Manual
Wireless Terminal Data Service Chapter 1 Modem
Chapter 1 Modem
Since a Modem has been built in T-1 ETS-2288 Fixed Wireless

Terminal (FWT) before delivery, you can enjoy such data services as
Web browse and data downloading by connecting the FWT to your
computer via a USB serial data cable. The USB serial data cable has
been supplied in the data kit, so you can purchase it from the local
carrier as required. Like the standard Modem used in common
computers, the Modem is easy to operate.
The procedure is as follows: 1) Connect the terminal to your

computer (for specific operations, refer to HUAWEI T-1 ETS-2288
Fixed Wireless Terminal User Manual). 2) Install the driver for your
operating system from the CD in the data kit.
1-1
User Manual
HUAWEI T-1 ETS-2288 Fixed Chapter 2 Configuration
Wireless Terminal Data Service Requirements
Chapter 2 Configuration Requirements
Minimum system requirements:

1) CPU: Pentium 100 or above.
2) Operating system: Windows 98, Windows 2000 or
Windows XP.
3) Support USB1.1 or higher interface standards.
4) Install IE browser and FTP client.
Caution:
Be sure not to install other USB-to-serial port devices on the same PC.
2-1
User Manual
Wireless Terminal Data Service Chapter 3 Wireless Data Service
Chapter 3 Wireless Data Service
3.1 Install HUAWEI WIRELESS MODEM Driver
3.1.1 Install Windows 98 system Driver

1) Insert the CD in the data kit into the CD-ROM. The default
driver directory is: E:\Setup. Double click the icon
“Setup.exe” to run Wireless Modem driver.
Note:
The CD-ROM drive E mentioned in the manual may be different from your actual
computer setting. You should find the driver directory in your own computer.
2) Then the system pops up the interface [Choose Setup

Language] shown in Figure 3-1, prompting you to select
the language for this installation. Either Chinese or English
can be selected depending on your operating system.
3-1
User Manual
Figure 3-1 Choose Setup Language
3) Click <OK> to enter the interface [Setup Prepare] shown in

Figure 3-2. It is strongly recommended that you exit all
Windows programs before running this Setup program.
Figure 3-2 Setup Prepare
3-2
User Manual
4) Click <Next> to enter the interface [Select Install Path]

shown in Figure 3-3. The default driver installation
directory is: C:\HUAWEI\MODEM. If required, you can click
<Browse> and change the destination installation path.
Figure 3-3 Select Installation Path
5) Click <Next>, and the system will detect whether USB

driver has been installed. If you use the terminal for the first
time, and previously have not installed UMP 3410 Unitary
Driver and UMP3410 Serial Port drivers, the system will
pop up the interface shown in Figure 3-4, and prompt you
to install USB driver following the three steps below.
Otherwise, the system will find the device via the
corresponding COM port (e.g., COM3) and prepare to
install HUAWEI WIRELESS MODEM.
3-3
User Manual
Figure 3-4 Install Guide
For the first case, specific procedure is described as follows:
Step 1: Connect one end (USB connector) of USB serial data

cable to the USB port on your computer, and the other end (DB9) to
the serial port on the terminal. The system will automatically find the
new device “UMP 3410 Unitary Driver” and install its driver.
Step 2: After “UMP 3410 Unitary Driver” driver installation, the

system will automatically find another new device “UMP3410 Serial
Port” and install its driver.
Step 3: In Figure 3-4, click <Next> to start to install HUAWEI

WIRELESS MODEM.
3-4
User Manual
6) The system prompts that Setup Program has installed

HUAWEI WIRELESS MODEM on your computer
successfully. Click <Finish> to complete the installation.
Figure 3-5 Setup Complete
7) After the driver installation, the system will add “HUAWEI

WIRELESS MODEM” in [Control Panel/Modems], as
shown in Figure 3-6.
3-5
User Manual
Figure 3-6 Modems Properties
8) The system will add “UMP 3410 Unitary Driver” in [Control

Panel/System/Device Manager/UMP], and “UMP 3410
Serial Port” in [Control Panel/System/Device
Manager/Ports (COM & LPT)], as shown in Figure 3-7.
3-6
User Manual
Figure 3-7 System Properties
3.1.2 Install Windows 2000 system Driver

“Setup.exe” to run Wireless Modem driver
Note:
3-7
User Manual


3-8
User Manual

3-9
User Manual
Figure 3-10 Select Install Path

driver has been installed. If you use the FWT for the first
time, and previously have not installed TIUSB3410 and
TIUMP SERIAL PORT drivers, the system will pop up the
interface shown in Figure 3-11, and prompt you to install
USB driver following the three steps below. Otherwise, the
system will find the device via the corresponding COM port
(e.g., COM7) and prepare to install HUAWEI WIRELESS
MODEM.
3-10
User Manual

the serial port on the FWT. The system will automatically find the new
device “TIUSB3410” and install its driver.
Step 2: After “TIUSB3410” driver installation, the system will

automatically find another new device “TIUMP USB Serial Port” and
install its driver.
After the two drivers installation, the system will automatically

add “TIUSB3410” in [Control Panel/System/Hardware/Device
Manager/ TI UMP Devices], and “TIUMP USB Serial Port” in [Control
3-11
User Manual
Panel/ System/Hardware/Device Manager/Ports (COM & LPT)], as


WIRELESS MODEM.
Figure 3-12 Device Manager
6) The system will find the device via the corresponding COM
port (e.g., COM7) and install its driver, as shown in Figure
3-13.
3-12
User Manual
Figure 3-13 Found Port Device
7) As shown in Figure 3-14, click <Yes> to continue the

installation.
Figure 3-14 Digital Signature Not Found
8) As shown in Figure 3-15, HUAWEI MODEM has been

installed successfully. Click <Finish> to complete the
installation.
3-13
User Manual
9) After the Modem driver installation, the system will add

“HUAWEI WIRELESS MODEM” in [Control
Panel/System/Hardware/Device Manager/Modems], as
3-14
User Manual
3.1.3 Install Windows XP system Driver

“Setup.exe” to run Wireless Modem driver.
3-15
User Manual
Note:


3-16
User Manual

3-17
User Manual
Figure 3-19 Select Install Path

driver has been installed. If you use the FWT for the first
time, and previously have not installed TIUSB3410 and
TIUMP SERIAL PORT drivers, the system will pop up the
interface shown in Figure 3-20, and prompt you to install
USB driver following the three steps below. Otherwise, the
system will find the device via the corresponding COM port
(e.g., COM4) and prepare to install HUAWEI WIRELESS
MODEM.
3-18
User Manual

the serial port on the FWT. The system will automatically find the new
device “TIUSB3410”, as shown in Figure 3-21. Select the radio
button followed by [Install the software automatically
(Recommended)], then click <Next>. The system will automatically
install its driver, as shown in Figure 3-22. Click <Finish> to close the
wizard.
3-19
User Manual
Figure 3-21 Found TIUSB3410
3-20
User Manual
Step 2: After “TIUSB3410” driver installation, the system will

automatically find another new device “TIUMP USB Serial Port” and
install its driver, as shown in Figure 3-23. Select the radio button
followed by [Install the software automatically (Recommended)],
then click <Next>. The system will automatically finish “TIUMP USB
Serial Port” driver installation and switch to Figure 3-24. Click
<Continue Anyway> to install its driver, as shown in Figure 3-25.
Click <Finish> to close the wizard.
Figure 3-23 Found TIUMP USB Serial Port
3-21
User Manual
Figure 3-24 Windows Logo Testing
Figure 3-25 Finish Installation
3-22
User Manual
After the two drivers installation, the system will automatically

add “TIUSB3410” in [Control Panel/System/Hardware/Device
Manager/ TI UMP Devices], and “TIUMP USB Serial Port” in [Control
Panel/ System/Hardware/Device Manager/Ports (COM & LPT)], as

WIRELESS MODEM.
3-23
User Manual
6) The system will find the device via the corresponding COM
port (e.g., COM4) and install its driver, as shown in Figure
3-27.
Figure 3-27 Found Port Device
7) As shown in Figure 3-28, click <Continue Anyway> to

install Modem driver.
Figure 3-28 Windows Logo Testing
3-24
User Manual
8) As shown in Figure 3-29, HUAWEI MODEM has been

installed successfully. Click <Finish> to complete the
installation.
9) After the Modem driver installation, the system will add

“HUAWEI WIRELESS MODEM” in [Control
Panel/System/Hardware/Device Manager/Modems], as
3-25
User Manual
3.2 Data Service Reference

You can perform data services such as high-speed packet data
access, low-speed data service access, and PC fax. For specific
operations of data services, consult your operator.
3-26
User Manual
3.2.1 High-speed Packet Data Access
I. Dial Up to the Internet on Windows 98
1) Click
[Start/Programs/Accessories/Communications/Dial-Up
Networking], and the Dial-Up Networking dialog box will
pop up. Double click [Make New Connection] to enter the
interface shown in Figure 3-31, and then type your custom
name for the computer that you are dialing (such as
“HUAWEI WIRELESS MODEM”). Select “HUAWEI
WIRELESS MODEM (153.6K)” in the drop-down list box,
and then click <Next>.
Figure 3-31 Select Modem
2) As shown in Figure 3-32, type the telephone number (such

as “#777”) as required in the text box and select the
3-27
User Manual
country or region code {e.g., United States of America (1)}

in the drop-down list box.
Figure 3-32 Type Dialing Number
3) Click <Next> to enter the interface shown in Figure 3-33,

then click <Finish> to complete the establishment of
Dial-Up Networking.
3-28
User Manual
Figure 3-33 Finish Dial-Up Networking Establishment
4) In the [Dial-Up Networking] dialog box shown in Figure

3-34, right click the icon “HUAWEI WIRELESS MODEM” to
pop up a shortcut menu, and then click [property] to
activate properties dialog box, and uncheck the check box
followed by [Use area code and Dialing Properties], as
3-29
User Manual
Figure 3-34 HUAWEI WIRELESS MODEM
3-30
User Manual
Figure 3-35 Dialing Properties
5) In the [Dial-Up Networking] dialog box shown in Figure

3-34, double click the icon “HUAWEI WIRELESS MODEM”
to pop up the [Connect To] dialog box, as shown in Figure
3-36. Then enter User name, Password and Phone
number in the corresponding text boxes. Click <Connect>
to enter the dialing state. If the user name and password
pass the authentication from the server, you can conduct
the data services.
3-31
User Manual
Figure 3-36 Dialing Setting
Caution:
You need to enter a high-speed packet access phone number in establishing a

dialup connection. The login user name and password may be different in different
networks. For more details, consult the local carrier while applying for the data
services.
II. Dial Up to the Internet on Windows 2000
1) Click
[Start/Programs/Accessories/Communications/Network
3-32
User Manual
and Dial-up Connections], and the [Network and Dial-up

Connections] dialog box will pop up. Click [File/Make New
Connection] to pop up the interface [Network Connection
Wizard], as shown in Figure 3-37. Then click <Next> to
continue.
Figure 3-37 Network Connection Wizard
2) As shown in Figure 3-38, select the radio button followed

by [Dial-up to private network], then click <Next>.
3-33
User Manual
Figure 3-38 Select Network Connection Type
3) As shown in Figure 3-39, if only HUAWEI WIRELESS

MODEM is installed in your operating system, you will not
see the following window. Otherwise, select “HUAWEI
WIRELESS MODEM”, and then click <Next>.
3-34
User Manual
Figure 3-39 Select the Modem
4) As shown in Figure 3-40, enter the phone number (e.g.,

“#777”) as required, and then click <Next>.
3-35
User Manual
Figure 3-40 Enter Phone Number

by [For all users], and then click <Next>.
Figure 3-41 Connection Availability
3-36
User Manual
6) As shown in Figure 3-42, type the name (e.g., “HUAWEI

WIRELESS MODEM") you want to use for this connection,
then click <Finish> to complete the establishment of dialing
connection.
Figure 3-42 Finish Network Connection
7) In the [Network and Dial-up Connections] window, double

click the new connection “HUAWEI WIRELESS MODEM"
to enter the interface shown in Figure 3-43, then click
<Dial> to enter the dialing state. If the user name and
password pass the authentication from the server, you can
conduct the data services.
3-37
User Manual
Figure 3-43 Dial-up to the Internet
Caution:

services.
3-38
User Manual
III. Dial Up to the Internet on Windows XP
1) Click [Start/Programs/Accessories/Communications/
Network Connections], and the [Network Connections]
dialog box will pop up. Click the menu item [Create a new
connection] to pop up the interface [New Connection
Wizard], as shown in Figure 3-44, and then click <Next>.
Figure 3-44 New Connection Wizard

by [Connect to the Internet], then click <Next>.
3-39
User Manual
Figure 3-45 Select Network Connection Type

by [Set up my connection manually] then click <Next>.
3-40
User Manual
Figure 3-46 Select Connection Mode

by [Connect using a dial-up modem], then click <Next>.
3-41
User Manual
Figure 3-47 Select a dial-up Modem
5) As shown in Figure 3-48, if only HUAWEI WIRELESS

MODEM is installed in your operating system, you will not
see the following window. Otherwise, select “HUAWEI
WIRELESS MODEM”, and then click <Next>.
3-42
User Manual
Figure 3-48 Select Modem
6) As shown in Figure 3-49, enter the ISP Name (e.g.,

“HUAWEI”) as required, and then click <Next>.
Figure 3-49 Enter ISP Name
3-43
User Manual
7) As shown in Figure 3-50, enter the Phone number (e.g.,

“#777”) as required, and then click <Next>.
Figure 3-50 Enter Phone Number
8) As shown in Figure 3-51, enter the User name and

Password as required, and then click <Next>.
3-44
User Manual
Figure 3-51 Enter Internet Account Information
9) As shown in Figure 3-52, click <Finish> to create the

connection and close this wizard.
3-45
User Manual
Figure 3-52 Finish Creating a Connection
10) In the [Network Connections] window, double click the new

connection “HUAWEI" to enter the interface shown in
Figure 3-53, then click <Dial> to enter the dialing state. If
the user name and password pass the authentication from
the server, you can conduct the data services.
3-46
User Manual
Figure 3-53 Dial up to the Internet
Caution:

services.
3-47
User Manual
3.2.2 Low-speed Data Service Access
Compared with high-speed packet data service access,

low-speed data service access provides a lower transfer rate. The
differences between them are that you need to type a corresponding
access telephone number, user name and password based on the
access information provided by your ISP.
Caution:
It is likely that the connection rate displayed by the system is the one on a serial port.
For a specific transfer rate, consult your operator.
3.2.3 PC Fax Service
You can use the PC fax service function to send/receive a fax. In

addition, you can choose PC fax software as required.
Note:
For specific operations of PC fax software, refer to the instruction of the relevant
software. This section only describes the relative operation of the FWT in
implementing a PC fax service.
3-48
User Manual
I. Preparations
1) Install HUAWEI WIRELESS MODEM driver on your PC.

2) Install the fax software on your PC.
II. Configuration Procedure
1) Connect one end of a USB cable to your PC, and the other
end to the FWT.
2) Open the switch on the FWT, and set the baud rate
between the FWT and your PC to 19200 bps through
operation menus. The operation procedures are as follows:
Step Operation
1 Press <MENU>, find [Settings], and then press <OK> to enter it.
2 Find [Common], and then press <OK> to enter it.

3 Find [Data Service], and then press <OK> to enter it.
Select [Data Rate], and press <OK> to enter it. The display screen shows
4 the current serial baud rate. Press or to set the serial baud
rate as 19200 bps.
5 Press <OK> to save the configuration.
Note:
If you unplug the data cable connecting the FWT and re-plug it, the baud rate of the
serial port on the FWT will restore to the default value (230400bps). To change the
rate, you need to reset the parameter.
3-49
User Manual
Caution:
After configuring the serial baud rate on the FWT, you need configure the same rate
for the PC fax software. For details, refer to the directions shipped with that
software.
III. PC fax sending and receiving
Before receiving fax data through PC, first you need to set the
FWT status as PC fax auto-receiving. The operation procedures are
as follows:
Step Operation
1 Press <MENU>, find [Settings], and then press <OK> to enter it.
2 Find [Common], and then press <OK> to enter it.
3 Find [Data Service], and then press <OK> to enter it.

Select [FAX Mode], and press <OK> to enter it. The display screen shows
the current fax auto-receiving status. “On” indicates to enable the PC fax
4
auto-receiving, while “Off” indicates to disable the PC fax auto-receiving.
Press or to set the fax auto-receiving status as “On”.
5 Press <OK> to save the configuration.
3-50
User Manual
Note:
To disable the PC fax auto-receiving, just set the fax auto-receiving status as “Off”.
Alternatively, you can reset the FWT to change the status as voice answering mode.
Caution:
To terminate PC fax data sending/receiving, you need to press <END>.
3-51
User Manual
Wireless Terminal Data Service Chapter 4 Precautions
Chapter 4 Precautions
1) To enable the FWT to connect to the Internet, make sure

that you have applied for the data services for the FWT
after purchasing the data suite from the carrier.
2) The login user name and password may be different in
different networks. For more details, consult the local
carrier while applying for the data services.
3) If you are using the PC fax, low-speed data service access
and high-speed data service access, related prompt will be
shown on the screen. In such case, the telephone is out of
service. To use the telephone service, please end the data
service applications on the PC first. If the FWT still shows
related information, please press <END>. Do not press this
key while the data service is still in use.
4) During the installation of data service driver, please strictly
follow the installation procedure described in this manual,
and decide when to insert the USB cable.
5) After the installation of data service driver, please make
sure the serial port of the Modem is consistent with the
USB port.
6) After the installation of data service driver, please check if
the Modem icon appears in the device explorer. If not,
refresh the current display and find it.
4-1
User Manual
Wireless Terminal Data Service Chapter 5 Troubleshooting
Chapter 5 Troubleshooting
I. The system prompts that the Modem has no response at

dial-up
1) Check whether you have switched on the FWT and

connected the USB serial data cable properly.
2) Check whether the wireless Modem driver has been
installed properly.
3) Check whether the baud rate on the serial interface of the
Modem is 230400bps (by default). If it is not, you need to
reset it to the default value and restart the FWT.
II. The system prompts that a dial-up networking

connection can not be created or that the dial-up network is not
connected to the server at dial-up
Check whether the user name and password typed are correct.
If the fault still exists, contact the operator.
III. The system prompts that the remote server has no

response at dial-up
1) Check whether the telephone number typed is correct. For

example, the telephone number is “#777” when you dial up
through the high-speed packet data service. For a specific
number, consult the operator.
2) It is possibly that the remote server is busy. Retry later.
5-1
User Manual
Wireless Terminal Data Service Chapter 5 Troubleshooting
3) Make sure that you have applied for the data services.
IV. The serial port number of the Modem is not consistent

with that of the USB in Win98/WinXP/Win2000 system
In Win98 system, you need to modify the serial port number of

the Modem so that the serial port number of the Modem is the same
as that of the USB. The process is shown as the follows:
1) Double click Modems at the control panel.
2) Select “HUAWEI WIRELESS MODEM (153.6K)”.
3) Click <Properties>.
4) Select “Communications Port”.
5) Click <Ok>.
In WinXP/Win2000 system, if the serial port number of the USB
is changed which is not consist with that of the Modem, you can not
modify the port number of the Modem. You must to reinstall the
Modem follow the following steps.
1) Double click “Phone and Modem Options” at the control
panel.
2) Select “Modems” tab.
3) Click <Add>.
4) Select “Don’t detect my modem; I will select it from a list”
5) Click <Have Disk…>.
6) Put the CD of the data service which is came with the
terminal to the CD-ROM and look for the following path:
Driver Files\WinXP(Win2000).
7) Select the serial port number which is the same as that of
the USB.
5-2

T-1 ETS-2288 FWT Data Service User Manual

Uploaded by

Copyright:

Available Formats

T-1 ETS-2288 FWT Data Service User Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

T-1 ETS-2288 FWT Data Service User Manual

Uploaded by

Copyright:

Available Formats

HUAWEI

HUAWEI T-1 ETS-2288 Fixed

Manual Version T2-030177-20050112-C-2.20

Huawei Technologies Co., Ltd. provides customers with

Huawei Technologies Co., Ltd.

Address: Administration Building, Huawei Technologies Co., Ltd.,

Bantian, Longgang District, Shenzhen, P. R. China

Postal Code: 518129

All Rights Reserved

No part of this manual may be reproduced or transmitted in any form

, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess,

The information in this manual is subject to change without notice.

The product version that corresponds to the manual is HUAWEI T-1

The following manuals provide more information about the HUAWEI

HUAWEI T-1 ETS-2288 Fixed Wireless Terminal Data Service User

Chapter 1 Modem describes the modem integrated with FWT.

Chapter 3 Wireless Data Service elaborates the operation of data

Chapter 4 Precautions describes the precautions of data service

Chapter 5 Troubleshooting introduces common faults and handling

The manual uses the following conventions:

Button names are inside angle brackets. For example,

III. Keyboard operation

IV. Mouse operation

Eye-catching symbols are also used in this manual to highlight the

Caution, Warning, Danger: Means reader be extremely careful

Note, Comment, Tip, Knowhow, Thought: Means a

This product has been designed to comply with the requirements on

Chapter 2 Configuration Requirements ......................................2-1

Chapter 3 Wireless Data Service..................................................3-1

Since a Modem has been built in T-1 ETS-2288 Fixed Wireless

The procedure is as follows: 1) Connect the terminal to your

Chapter 2 Configuration Requirements

Minimum system requirements:

Chapter 3 Wireless Data Service

3.1 Install HUAWEI WIRELESS MODEM Driver

3.1.1 Install Windows 98 system Driver

2) Then the system pops up the interface [Choose Setup

Figure 3-1 Choose Setup Language

3) Click <OK> to enter the interface [Setup Prepare] shown in

Figure 3-2 Setup Prepare

4) Click <Next> to enter the interface [Select Install Path]

Figure 3-3 Select Installation Path

5) Click <Next>, and the system will detect whether USB

Figure 3-4 Install Guide

For the first case, specific procedure is described as follows:

Step 1: Connect one end (USB connector) of USB serial data

Step 2: After “UMP 3410 Unitary Driver” driver installation, the

Step 3: In Figure 3-4, click <Next> to start to install HUAWEI

6) The system prompts that Setup Program has installed

Figure 3-5 Setup Complete

7) After the driver installation, the system will add “HUAWEI

Figure 3-6 Modems Properties

8) The system will add “UMP 3410 Unitary Driver” in [Control

Figure 3-7 System Properties

3.1.2 Install Windows 2000 system Driver

2) Then the system pops up the interface [Choose Setup

Figure 3-8 Choose Setup Language

3) Click <OK> to enter the interface [Setup Prepare] shown in

Figure 3-9 Setup Prepare

4) Click <Next> to enter the interface [Select Install Path]