Cicol Etslurry

Cicol ET Slurry*
Heavy duty, lightweight, anti-skid surface

dressing
Uses
Design criteria
Cicol ET Slurry provides a lightweight, yet extremely hard

wearing anti-skid surface to a variety of substrates including
steel, concrete, asphalt and timber.
The thickness of the Cicol ET Slurry is varied to suit traffic

conditions as shown in the table below.
Ideally suited for foot and road bridges, RO/RO linkspans,

helicopter decks, work platforms, ships decks, car parks,
walkways, wet work industrial areas and cargo handling areas,
etc.
Advantages
n Lightweight
n Hard wearing
n Flexible
n Excellent adhesion to steel and concrete substrates
n Non-slip, excellent grip even when wet
Traffic
density
Medium
Heavy
:
:
Cicol ET Slurry
thickness
Aggregate
type
Nominal
thickness
3.0mm
3.0mm
20 mesh
1 to 3mm
3.5mm
5.5mm
The final thickness of the finished surface dressing will be

between 3.5 -5.5mm depending upon the exact system
chosen to meet the expected end use.
For Specialised uses other than the aforesaid uses, a
4.5 mm thick coating of Cicol ET Slurry with 3 - 5mm aggregate
can be used to give a nominal thickness of 8mm.
Cicol ET Slurry HB* is recommended on ramps with a slope
greater than 5C.
n Chemically resistant
n Waterproof
Properties
n Zero spread of flame
Pot life at 20C
30 mins
Standards compliance
Specific gravity
Curing time at 20C
:
:
1.74
Foot traffic after 24 hours,
vehicular traffic after 48 hours
Resistance to flame spread (BS 476, Pt 7 clause 2:1971). In

independent tests Cicol ET Slurry was awarded a class 1
grading.
Description
Cicol ET Slurry is a three component system based upon

solvent free, coal tar modified epoxy resins, amine curing
agents and chemically inert, graded silica fillers which when
mixed forms a fluid, homogeneous slurry.
Cicol ET Slurry
Specially selected Dynagrip aggregates are broadcast onto

this slurry whilst it is still wet to provide a lightweight, flexible,
durable, anti-skid dressing which can be used on a variety of
substrates including steel, concrete, timber and aluminium.
Fully cured Cicol ET Slurry has been shown to be resistant to

the following chemicals after continuous immersion for 12
months at 20C:
Chemical resistance
Petrol
Kerosene
Hydraulic fluids,
Dilute mineral acids and alkalis
10% Urea in water
De-icing salts
Diesel
Aircraft fuel
Instructions for use
Mixing
Preparation
Mix the base and hardener thoroughly using a slow speed

drill and Fosroc Mixing Paddle (MR3), or forced action mixers
such as creteangle or zyklos. Add the mineral fillers and mix
until a homogeneous slurry consistency is formed. The total
mixing operation should take about 5-7 minutes. The
Cicol ET Slurry is now ready for use. Do not add thinners or
solvent.
Cicol ET Slurry can be applied to a variety of substrates. As

with all flooring materials or protective coatings, correct
surface preparation is essential.
Steel substrates
Cicol ET Slurry is specially formulated to exhibit excellent
adhesion to un-primed steel. However, all steel substrates
should be blast cleaned to a minimum Sa21/2 standard of
cleanliness. An angular profile amplitude of at least 75 microns
is recommended.
The slurry should be applied as quickly as possible to the
blasted steel surface. If the standard of the surface falls below
Sa21/2 then the steel must be reblasted.
Concrete substrates
Cicol ET Slurry is applied to clean, sound, dry concrete
substrates which are free of any laitance or loose particles.
Mechanical scarifying or blasting methods are strongly
recommended.
Prepared concrete substrates should be primed with
Nitoprime 25 which is applied by lambswool roller to provide
a thin even coverage. Avoid over application and puddles.
Cicol ET Slurry is applied onto the Nitoprime 25 as soon as it
is free from surface tack.
Asphalt substrates
Application
Once mixed the Cicol ET Slurry must be used within the
specified pot life.
Pour the slurry onto the prepared surface. Work in lanes of
2-3 m wide masking off edges with tape. Spread the slurry
using a steel trowel or squeegee taking particular care when
joining up to the previous day's work.
Use of a wet film gauge is recommended to ensure the correct
thickness and material usage. The Dynagrip surface dressing
aggregate must be applied immediately after laying the
Cicol ET Slurry.
The slurry coating is blinded to saturation by allowing the
aggregate to fall vertically until no slurry is visible. Do not
throw aggregate across the slurry as this may cause ridges.
Masking tape must be removed before the coating has cured.
The Cicol ET Slurry must be allowed to cure for 24 hours at
20C before being subject to foot traffic. At lower temperatures
this period will be increased.
Cicol ET Slurry can be applied onto asphalt substrates

providing they are clean, sound and dry. It is also
recommended that the asphalt should be at least 12 months
old.
Cleaning
Asphalt should be lightly grit blasted to remove any weakly

bonded or contaminated material to provide the desired
surface. No primer is required on asphalt.
Limitations
All tools can be cleaned immediately after use with Fosroc

Solvent 102.
Cicol ET Slurry should not be applied when the relative

humidity is greater than 80% or the ambient temperature
is expected to fall below 5C.
Cicol ET Slurry should not be applied on ramps with a slope

greater than 5%.
Wooden substrates
Cicol ET Slurry can be applied directly onto clean, dry timber
substrates.
Aluminium substrates
Technical support
Must be sweep blasted and degreased if necessary using

Fosroc Solvent 102* to provide a sound mechanical key.
Cicol ET Slurry can be applied directly to the prepared
substrate.
Fosroc offers a comprehensive range of high performance,

high quality flooring, jointing and repair products for both new
and existing floor surfaces. In addition, Fosroc offers a
technical support package to specifiers, end users and
contractors, as well as on-site technical assistance in locations
all over the world.
Cicol ET Slurry - Page 2 of 4
Estimating
Precautions
Supply
Health and safety
Cicol ET Slurry
Nitoprime 25
:
:
20 litre packs
1 & 4 litre packs
3.0 litre/m2 @ 3mm thick
Cicol ET Slurry, Nitoprime 25 and Solvent 102 should not come

into contact with the skin or eyes, or be swallowed. Ensure
adequate ventilation and avoid inhalation of vapours.
Coverage
Cicol ET Slurry
Dynagrip
Aggregate
20 mesh
1.0 to 3.0
Nitoprime 25
Notes :
Gross (kg/m2)
Net (kg/m2)
5.5
3.7
7.0
5.2
: 4.0 - 5.0 m2/litre
Coverage figures given are theoretical - due to

wastage factors and the variety and nature of
possible substrates, practical coverage figures will
be reduced - site trials are recommended.
For specialised uses, please contact the local
Fosroc office for coverage figures.
Some people are sensitive to resins, hardeners and solvents.

Wear suitable protective clothing, gloves and eye protection.
If working in confined areas, suitable respiratory protective
equipment must be used.
The use of barrier creams provide additional skin protection.
In case of contact with skin, rinse with plenty of clean water,
then cleanse with soap and water. Do not use solvent.
In case of contact with eyes, rinse immediately with plenty of
clean water and seek medical advise. If swallowed, seek
medical attention immediately - do not induce vomiting.
Fire
Fosroc Solvent 102 is flammable. Ensure adequate ventilation.
Do not use near naked flame. Do not smoke.
Storage
Shelf life
All products have a shelf life of 12 months if kept in a dry
store in the original, unopened packs.
Storage conditions
Store in dry conditions between 5C and 30C away from
sources of heat and naked flames, in the original, unopened
packs. If stored at high temperatures the shelf life will be
reduced.
Flash points (Abel closed cup)
Fosroc Solvent 102
Nitoprime 25
:
:
33oC
39C
Cicol ET Slurry - Page 3 of 4
Additional Information
Fosroc manufactures a wide range of complementary products

which include :
n waterproofing membranes & waterstops
n joint sealants & filler boards
n cementitious & epoxy grouts
n specialised flooring materials
Fosroc additionally offers a comprehensive package of
products specifically designed for the repair and refurbishment
of damaged concrete. Fosrocs Systematic Approach to
concrete repair features the following :
n hand-placed repair mortars
n spray grade repair mortars
n fluid micro-concretes
n chemically resistant epoxy mortars
n anti-carbonation/anti-chloride protective coatings
n chemical and abrasion resistant coatings
For further information on any of the above, please consult
your local Fosroc office - as below.
* Denotes the trademark of Fosroc International Limited
REGIONAL SALES OFFICES IN :
Al Gurg Fosroc LLC

P. O. Box 657
Dubai
United Arab Emirates
TEL : (04) 285 8606
FAX : (04) 285 9649
DUBAI
ABU DHABI
BAHRAIN
KUWAIT
OMAN
QATAR
Al Gurg Fosroc
Al Gurg Fosroc
YBA Kanoo
Boodai
GETCO
Tadmur
TEL : 285 8787
TEL : 673 1779
TEL : 738200
TEL : 481 7618
TEL : 771 5080
TEL : 441 3628
FAX : 285 2023
FAX : 673 1449
FAX : 732828
FAX : 483 2124
FAX : 771 7554
FAX : 444 0812
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of
which may be obtained on request. Whilst Fosroc endeavours to ensure that the technical information on this data sheet is correct at the time of printing,
it is the customers responsibility to satisfy himself, by checking with the company that this information is still current at the time of use, that the product is
suitable for the intended application, and that the actual conditions of use are in accordance with those recommended. Because Fosroc has no control over
the conditions of use of its products, all recommendations or suggestions regarding the use of these products are made without guarantee.
www.fosrocgulf.com
UAE/0302/01/B

Cicol Etslurry

Uploaded by

Copyright:

Available Formats

Cicol Etslurry

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cicol Etslurry

Uploaded by

Copyright:

Available Formats

Cicol ET Slurry*

Heavy duty, lightweight, anti-skid surface

Cicol ET Slurry provides a lightweight, yet extremely hard

The thickness of the Cicol ET Slurry is varied to suit traffic

Ideally suited for foot and road bridges, RO/RO linkspans,

The final thickness of the finished surface dressing will be

n Zero spread of flame

Pot life at 20C

Resistance to flame spread (BS 476, Pt 7 clause 2:1971). In

Cicol ET Slurry is a three component system based upon

Specially selected Dynagrip aggregates are broadcast onto

Fully cured Cicol ET Slurry has been shown to be resistant to

Instructions for use

Mix the base and hardener thoroughly using a slow speed

Cicol ET Slurry can be applied to a variety of substrates. As

Cicol ET Slurry can be applied onto asphalt substrates

Asphalt should be lightly grit blasted to remove any weakly

All tools can be cleaned immediately after use with Fosroc

Cicol ET Slurry should not be applied when the relative

Cicol ET Slurry should not be applied on ramps with a slope

Must be sweep blasted and degreased if necessary using

Fosroc offers a comprehensive range of high performance,

Cicol ET Slurry - Page 2 of 4

Health and safety

3.0 litre/m2 @ 3mm thick

Cicol ET Slurry, Nitoprime 25 and Solvent 102 should not come

Coverage figures given are theoretical - due to

Some people are sensitive to resins, hardeners and solvents.

Cicol ET Slurry - Page 3 of 4

Fosroc manufactures a wide range of complementary products

* Denotes the trademark of Fosroc International Limited

REGIONAL SALES OFFICES IN :

Al Gurg Fosroc LLC

TEL : 285 8787

TEL : 673 1779

TEL : 481 7618

TEL : 771 5080

TEL : 441 3628

FAX : 285 2023

FAX : 673 1449

FAX : 483 2124

FAX : 771 7554

FAX : 444 0812

You might also like