Triaxial Test Procedure

DETERMINATION OF TRIAXIAL SHEAR
PARAMETERS USING SIMPLE TRIAXIAL TEST

1
SCOPE
This method describes the determination of triaxial shear parameters (cohesion and
internal angle of friction) of Bitumen Stabilised Materials by measuring the resistance to
failure (monotonic) of a cylindrical 150 mm diameter and 300 2 mm height specimen
prepared according to Vibratory Hammer Compaction Procedure (Appendix L of the
Technical Memorandum on Updating Bituminous Stabilised Materials Guidelines Mix
Design Report Phase II).
2
2.1
APPARATUS
Triaxial Cell
Comprising:
Galvanised steel casing 5 mm thick comprising a ring handle and simple mechanical
clamps top and bottom
A base with bottom platen for sitting specimen
Top disk; and
Latex tube at least 320 mm height.
2.2
Testing System
Material Testing System (MTS) or its equivalent system must at least comprise of an
actuator, reaction frame, control panel and data acquisition system. The system must
be capable of providing ramp loads with minimum loading capacity of 100 kN and a
minimum stroke of 40 mm.
It is preferable that the actuator be operated by a servo-controlled hydraulic pressure
system with a closed loop feedback system that is capable of both displacement and
load
controlled testing if required.
2.3
Measuring Devices
Measuring devices should include but not limited to:
Load cell (100 kN Capacity) for measuring load
Actuator displacement transducer (> 40 mm stroke) for measuring displacement
(deformation)
Pressure regulator, gauges, and valves for lateral pressure
2.4
Others
Air compressor
Loading ram
Silicon oil or grease
SPECIMEN PREPARATION
Specimen must be prepared according to Vibratory Hammer Compaction Procedure
(Appendix L) and cured according to curing protocol suggested in Appendix G and H of
the Technical Memorandum on Updating Bituminous Stabilised Materials Guidelines

Mix Design Report Phase II Report.
4
4.1
PROCEDURE
Assembly of specimen in a triaxial cell
The triaxial testing of the specimens must be planned to take place within 48 72
hours after completion of the curing procedure. This delay must be kept as constant as
possible.
The following steps describe the procedure taken to assemble specimen in the simple
triaxial cell and the cell in the loading frame:
(i)
Place the specimens, casing with

tube, top disk and base plate in a
climate chamber and condition them
overnight at 25C.
(ii)
Lightly grease the sides of the top

disk and base plate to reduce friction
as much as possible.
(iii)
Place the specimen in the middle of

the base plate.
(iv)
Carefully introduce the casing,

comprising the tube, around the
specimen. Take care not to damage
the edges of the specimen during
this procedure.
(v)
Clamp the casing in position on to

the base plate using simple
mechanical clamps on the casing.
(vi)
Put the top disk on top of the

specimen.
(vii) Place the cell in the hydraulic

loading frame; adjust actuator
position until visual contact is made
with the loading ram.
(viii) Connect the air supply to the cell;
open the regulator and valve on the
cell pressure port until the cell
pressure is stable at the desired
level.
(ix)
Set monotonic test parameters on

the MTS controller including
displacement rate of strain (2.1%),
full-scale for the loading (10.0V =
98.1 kN) and half-scale for the
displacement (10.0V = 40mm)
(x)
Run the test.
4.2
Monotonic Triaxial Test

Select four specimens of comparable density, moisture content and conditioned at
25oC. Assemble the specimen in the triaxial cell according to 4.1. Ensure the tube is air
tight by observing step (iv) in 4.1 above.
Operate the testing system in displacement control mode. Ensure that there is
sufficient space between the actuator and the reaction frame to accommodate the
triaxial cell. Place the triaxial cell in the hydraulic loading frame as shown in step (vii) in
4.1 above.
Adjust the actuator position until visual contact is made with the loading ram. Monitor
the load cell reading to prevent loading of the specimen during this process.
Connect the air supply to the cell pressure port. Open the valve on the cell pressure
port and open the regulator until the cell pressure is stable at the desired level. The
cell pressures for a series of monotonic tests are 0 kPa, 50kPa, 100 kPa and 200 kPa.
Test the first specimen without confinement pressure (0 kPa). Begin the test by
compressing the specimen at a constant rate of displacement of 2.1%. Record the load
versus displacement during the test with a minimum sampling rate of 10 Hz, as well as
the cell pressure, temperature and specimen identifier.
Stop the test and the recording when the total displacement exceeds 18 mm (6%
strain) or when the specimen bulges excessively before the end displacement is
reached.
Repeat this procedure for other three specimens until all specimens have been tested
at the four levels of confinement pressures.
Remove the specimen according to 4.3.
4.3
Removal of specimen after completion of test

After completion of a test, hold the actuator to its current position, close the valve on
the cell pressure port and release the cell pressure by disconnecting the pressure
supply tube to the cell (if possible speed up the pressure release by applying suction).
Return the actuator to a position whereby the cell can easily be removed from the
loading frame.
Remove the top disk. Clean the top disk and wipe it of any grease.
Unclamp the casing and lift the casing with tube from the cell base. Clean the tube
from possible remains of the deformed specimen (it is not necessary to remove the
tube from the casing).
Remove the tested specimen from the base plate. Place it in the plastic bag and seal.
Clean the base plate and wipe it of any grease.
Once all the specimens have been tested, remove the tested specimens one by one
from the plastic bags. Break the tested specimens up and sample between 500 and
1000 gr. of material from the middle of the specimen.
Use this sample to determine the moisture content during testing according to the
procedure given in TMH1 Method A7.
CALCULATIONS
(i)
Determine the applied failure load Pa,f for each specimen tested. The applied
failure load is defined as the maximum applied load during the test. Calculate
the applied failure stress a,f :
a, f =
Pa , f
A
10 3
Where
a,f = applied failure stress [kPa]

Pa,f = applied failure load [N]
A = end area of a cylindrical specimen at beginning of test [m2]
(ii)
Calculate the major principle stress at failure 1,f for each tested specimen:
1, f = a , f + dw
Where
1,f = major principle stress at failure [kPa]
a,f = applied failure stress [kPa]
d,w = pressure resulting from dead weight of top disk and loading ram [kPa]
(iii)
According to Jenkins et al (2007), the relationship between 1,f and

confinement stress (3)is described by:
1, f = A 3+ B
Where
A=
1 + sin
1 sin
And
B=
2 C cos
1 sin
Values of A and B can be determined by performing a linear regression analysis

on the four combinations of 1,f and 3 per mix.
(iv)
Values of [o] and C [kPa] can be calculated as follows:
A 1
A +1
= sin 1
C=
B(1 sin )
2 cos
REPORT
Report
the following in the table format as illustrated in Table 1 below:

Specimen number or identifier;
Confinement pressure (3);
Applied stress at failure (a,f);
Major principal stress at failure (1,f);
Cohesion, C [kPa];
Angle of internal friction, [o]; and
Coefficient of variance, R2
Plot the Mohr Circles and the Mohr-Coulomb failure envelope as shown in Figure 1.
Note from Figure 1 that:
The centre of Mohr circle must be on the abscissa and is given by (1,f + 3)/2;
The radius of such circle is (1,f - 3)/2;
Angle of internal friction is the angle of the Mohr-Coulomb failure envelope
(failure line); and
The failure line intersects with ordinate at the cohesion value
Table 1: Table Format Report for Simple Triaxial Test
Specimen
No.
Confining
Pressure,
3
[kPa]
Applied
Stress
at
Failure
a,f
[kPa]
Principle
stress at
Failure
1,f
[kPa]
Cohesion
[kPa]
Internal
Friction
Angle
[o ]
Correlation
Coefficient
[R2]
Figure 1 Example of Mohr Circle Plot
REFERENCE PROTOCOLS AND STANDARDS
(i) Jenkins, K. J. and Ebels, L. J., 2007. Determination of Shear Parameters, Resilient
Modulus and Permanent Deformation Behaviour of Unbound and Bound
Granular Materials Using Triaxial Testing on 150 mm by 300 mm high
Specimens, Technical Memorandum First Draft May 2007.
Stellenbosch, South
Africa, 2007.
(ii) Texas Department of Transport, 2002. Triaxial Compression for disturbed soils and
base materials, TxDOT Designation: Tex-117-E, August 2002.

Triaxial Test Procedure

Uploaded by

Copyright:

Available Formats

Triaxial Test Procedure

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Triaxial Test Procedure

Uploaded by

Copyright:

Available Formats

DETERMINATION OF TRIAXIAL SHEAR

PARAMETERS USING SIMPLE TRIAXIAL TEST

the Technical Memorandum on Updating Bituminous Stabilised Materials Guidelines

Place the specimens, casing with

Lightly grease the sides of the top

Place the specimen in the middle of

Carefully introduce the casing,

Clamp the casing in position on to

Put the top disk on top of the

(vii) Place the cell in the hydraulic

Set monotonic test parameters on

Run the test.

Monotonic Triaxial Test

Removal of specimen after completion of test

a,f = applied failure stress [kPa]

According to Jenkins et al (2007), the relationship between 1,f and

Values of A and B can be determined by performing a linear regression analysis

Values of [o] and C [kPa] can be calculated as follows:

the following in the table format as illustrated in Table 1 below:

Table 1: Table Format Report for Simple Triaxial Test

Figure 1 Example of Mohr Circle Plot

REFERENCE PROTOCOLS AND STANDARDS

You might also like