Quick Start Guide

CX-One campaign Quick Start guide
Procedure to setup PLC and HMI using CX-One

This procedure describes how to download settings to the PLC using CX-Integrator.
It also explains how to download a NS HMI project trough the PLC to the NS terminal.
For this we use Ethernet connection from computer to PLC.
In the CX-Integrator project files we configured an IP address 10.0.0.4 for the PLC.
Please take necessary steps to allow you computer to be able to connect to the PLC using this IP address or
change the IP address in the project files.
In this procedure we download settings with a serial cable to the PLC, but of course it is also possible to
use only an Ethernet cable to start setting up the PLC. For this you can use the default factory IP address in
the Ethernet unit: 192.168.250.x, where x is the node number set by the rotary switches on the Ethernet
unit.
Notice that the node number is set in hexadecimal number.
Connect cables
After unpacking your products perform the following steps:
1.
2.
3.
4.
5.
6.
Connect 24V power supply to PLC and to HMI.

Connect serial programming cable (XW2Z-S002) to PLC and your computer.
Later connect serial HMI cable (XW2Z-200T) to Port A on NS and to the PLC serial port.
Connect Ethernet cross-cable to PLC and your computer.
Set node address on Ethernet unit other than 0.
Set dip-switch 5 to On to use default communication settings for the compter to connect to CPU.
Download project files

After you installed the software you can follow the steps below to download all project files.
1.
2.
Unzip CX-One files.zip file to you hard disk.

Open CJ1M-ETN_NS5M.cin using CX-Integrator.
Click in the menu on Network Auto Online and this window will appear:
3.
Change Comm. Port if you use a different port than COM1 and click OK to go online.
CX-Integrator should look similar to this picture:
1/8
4.
In the Online Information window right-click Target PLC [CJ1M-CPU11] and choose Mode
Setting from the popup menu.
In the window that will appear choose Program and click on the Set button. Then click Close.
2/8
5.

In the Project Workspace right-click Serial_Network(NTLink) and choose Connect from the popup
menu. In the popup window select CPU Port(252) : Serial Port and click on Ok.
CX-Integrator should look similar to this picture:
6.
Click in the menu on Network Transfer [PC to network] to download all settings to the CPU.
Click Yes and Ok on the next two message boxes. For the NS there are no parameters so you will
see a warning that you can ignore.
3/8
7.

In the Online Information window right-click Target PLC [CJ1M-CPU11] and choose Start
Routing Table from the popup menu.
In the routing table window open the file Routing Table.rtg. The window should now display the
following after opening the file:
In the Options menu choose Transfer to PLC to download the routing table to the PLC.
After downloading click Yes and Ok and close the window. You dont need to save the file.
8.
In the Project Workspace double-click Network1(Ethernet) to open the Ethernet unit. Right-click
the Unit icon CJ1M-CPU11 and select Change connection to this PLC. CX-Integrator should look
similar to this picture:
4/8
9.
Click in the menu on Network Transfer [PC to network] to download all settings to the Ethernet
unit. Click Yes and Ok on the next two message boxes.
The Ethernet IP address is 10.0.0.4. Right-Click the unit and select Parameters Edit to change
the IP address and Subnet mask.
10. Set the dip-switch 5 to Off to use the settings just downloaded and switch cable to connect the
serial HMI cable (XW2Z-200T) to Port A on NS and to the PLC serial port.
11. In the Serial_Network window right-click NS5 icon and choose Start Special Application and then
Start Only from the popup menu. The NS-Designer software will now start.
5/8

12. In the NS-Designer File menu choose Open Project and select the file named:
CX_One_NS5M.IPP and click Ok.
It will show the screen list now. Click Ok and then choose Transfer data from the File menu.
The following window appears:
13. Click the Comms. Method button.

14. In the Comms. Method window configure the following settings:
Select the Auto-reset after the transmission option.

Select the Pass through PLC option.
6/8

-
Select Ethernet for the first Comms. Method.

Select NT Link for the second Comms. Method.
Click the Set button on the right side of the Ethernet selection for the first Comms. Method.
Configure the following settings:
For the Driver tab configure these settings and after click OK to close the window:
Click the Set button on the right side of the NT Link selection for the second Comms. Method.
Configure the following settings:
Click OK.
Click OK again to close the Comms. Method window.
15. The Comms. Setting in the right upper corner of the Screen Data Transfer window should display
the following:
7/8
16. If the settings are all ok we can now download the NS HMI project to the NS HMI terminal
through the PLC over Ethernet. To do this, click the Connect button to make a connection to NS.
17. When you succeeded in making a connection to the NS the Screen Data Transfer window will be
similar to this picture:
Also the NS will show a screen Connection Complete. If you still see a message box, please press
OK.
18. Click the D button to download the project to the NS HMI terminal. When the download is
finished the NS will reboot and when finished will display the first screen.
Press the screen to continue in the project and it should be possible to read data from the PLC.
8/8

Quick Start Guide

Uploaded by

Copyright:

Available Formats

Quick Start Guide

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quick Start Guide

Uploaded by

Copyright:

Available Formats

CX-One campaign Quick Start guide

Procedure to setup PLC and HMI using CX-One

Connect 24V power supply to PLC and to HMI.

Download project files

Unzip CX-One files.zip file to you hard disk.

CX-One campaign Quick Start guide

CX-One campaign Quick Start guide

CX-Integrator should look similar to this picture:

CX-One campaign Quick Start guide

CX-One campaign Quick Start guide

CX-One campaign Quick Start guide

13. Click the Comms. Method button.

Select the Auto-reset after the transmission option.

CX-One campaign Quick Start guide

Select Ethernet for the first Comms. Method.

CX-One campaign Quick Start guide

You might also like