Designation: D721 06 (Reapproved 2011)

Designation: 158/69(85)

Standard Test Method for

Oil Content of Petroleum Waxes1

This standard is issued under the fixed designation D721; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon () indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.

NOTE 1With some types of waxes, of oil contents greater than 5 %,

there may be an incompatibility with MEK resulting in the formation of
two liquid phases. If this occurs, the test method is not applicable to the
material under test.

1.2 The values stated in inch-pound units are to be regarded

as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
and are not considered standard.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:3
D938 Test Method for Congealing Point of Petroleum
Waxes, Including Petrolatum
E1 Specification for ASTM Liquid-in-Glass Thermometers

This test method is under the jurisdiction of ASTM Committee D02 on

Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
D02.10.0A on Physical/Chemical Properties.
Current edition approved Oct. 1, 2011. Published October 2011. Originally
approved in 1943. Last previous edition approved in 2006 as D721-06. DOI:
10.1520/D0721-06R11.
In the IP, this test method is under the jurisdiction of the Standardization
Committee. This test method was issued as a joint ASTM-IP tentative in 1964.
This test method was prepared jointly by the Technical Association of Pulp and
Paper Industry and ASTM International.
This test method has been adopted for use by government agencies to replace
Method 5431 of Federal Test Method Standard No. 79lb.
2
This test method is being used by some laboratories for products of higher oil
content.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
Standards volume information, refer to the standards Document Summary page on
the ASTM website.

E128 Test Method for Maximum Pore Diameter and Permeability of Rigid Porous Filters for Laboratory Use
2.2 Energy Institute Standards:
Specification for IP Standard Thermometers4
3. Summary of Test Method
3.1 The sample is dissolved in methyl ethyl ketone, the
solution cooled to 32C (25F) to precipitate the wax, and
filtered. The oil content of the filtrate is determined by
evaporating the methyl ethyl ketone and weighing the residue.
4. Significance and Use
4.1 The oil content of a wax may have significant effects on
several of its properties, such as strength, hardness, flexibility,
scuff resistance, coefficient of friction, coefficient of expansion,
melting point, and oil straining. The importance of these effects
may be dependent upon the ultimate use of the wax.
5. Apparatus
5.1 Filter Stick and Assembly, consisting of a 10-mm
diameter sintered glass filter stick of 10 to 15 m maximum
pore diameter as determined by the method in Appendix X1,
provided with an air pressure inlet tube and delivery nozzle. It
is provided with a ground-glass joint to fit a 25 by 170-mm test
tube. The dimensions for a suitable filtration assembly are
shown in Fig. 1.
NOTE 2A metallic filter stick may be employed if desired. A filter
stick made of stainless steel and having a 12.7mm (12-in.) disk of 10 to
15-m maximum pore diameter, as determined by Test Method E128, has
been found to be satisfactory.5 The metallic apparatus is inserted into a 25
by 150mm test tube and held in place by means of a cork.

4
Available from Energy Institute, 61 New Cavendish St., London, WIG 7AR,
U.K.
5
The sole source of supply of a suitable metal filter stick with designated
porosity G known to the committee at this time is the Pall Corporation, 2200
Northern Boulevard East Hills, NY 11548. A list of United Kingdom suppliers can
be obtained from Energy Institute, 61 New Cavendish St., London, W1G 7AR,
United Kingdom. If you are aware of alternative suppliers, please provide this
information to ASTM International Headquarters. Your comments will receive
careful consideration at a meeting of the responsible technical committee,1 which
you may attend.

Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.

Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

1Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

1. Scope
1.1 This test method covers the determination of oil in
petroleum waxes having a congealing point of 30C (86F) or
higher as determined in accordance with Test Method D938,
and containing not more than 15 % of oil.2

D721 06 (2011)

All dimensions are in millimetres

FIG. 1 Filter Stick

5.2 Cooling Bath, consisting of an insulated box with 30 6

5-mm (1.2 6 0.2-in.) holes in the center to accommodate any
desired number of test tubes. The bath may be filled with a
suitable medium such as kerosine, and may be cooled by
circulating a refrigerant through coils, or by using solid carbon
dioxide. A suitable cooling bath to accommodate three test
tubes is shown in Fig. 2.
5.3 Pipet, or equivalent dispensing device capable of delivering 1 6 0.05 g of molten wax.
5.4 Transfer Pipet, or equivalent volume dispensing device,
capable of delivering 15 6 0.06 mL.
5.5 Air Pressure Regulator, designed to supply air to the
filtration assembly (8.5) at the volume and pressure required to
give an even flow of filtrate. Either the conventional pressurereducing valve or a mercury bubbler-type regulator has been
found satisfactory. The latter type, illustrated in Fig. 3, consists
of a 250-mL glass cylinder and a T-tube held in the cylinder by
means of a rubber stopper grooved at the sides to permit the
escape of excess air. The volume and pressure of the air
supplied to the filtration assembly is regulated by the depth to
which the T-tube is immersed in mercury at the bottom of the
cylinder. Absorbent cotton placed in the space above the
mercury prevents the loss of mercury by spattering. The air
pressure regulatory is connected to the filter stick and assembly
by means of rubber tubing.
5.6 Temperature Measuring Device:
5.6.1 Thermometer, having a range as shown below and
conforming to the requirements as prescribed in Specification
E1, or in the Specification for IP Standard Thermometers.
Copyright ASTM International
Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

Thermometer Number
ASTM
IP
71C
72C
71F
72F

5.6.2 Temperature measuring devices other than those described in 5.6.1 are satisfactory for this test method, provided
that they exhibit the same temperature response as the equivalent mercury-in-glass thermometers.
5.7 Weighing Bottles, glass-stoppered, having a typical capacity of 15 to 25 mL.
5.8 Evaporation Assembly, consisting of an evaporating
cabinet and connections, essentially as illustrated in Fig. 4, and
capable of maintaining a temperature of 35 6 1C (95 6 2F)
around the evaporation flask. Construct the jets with an inside
diameter of 4 6 0.2 mm for delivering a stream of clean, dry
air vertically downward into the weighing bottle. Support each
jet so that the tip is 15 6 5 mm above the surface of the liquid
at the start of the evaporation. Supply purified air at the rate of
2 to 3 L/min per jet. One way to purify the air is by passage
through a tube of approximately 10-mm bore packed loosely to
a height of approximately 200 mm with absorbent cotton.
Periodically check the cleanliness of the air by evaporating 4
mL of methyl ethyl ketone by the procedure specified in 8.5.
When the residue does not exceed 0.1 mg, the evaporation
equipment is operating satisfactorily.
5.9 Analytical Balance, capable of reproducing weights to
0.1 mg.
5.10 Wire StirrerA piece of stiff wire, made of iron,
stainless steel, or Nichrome wire of about No. 20 B & S (0.9
mm in diameter) or 16 swg gage, 250 mm long. A 10-mm
diameter loop is formed at each end, and the loop at the bottom
end is bent so that the plane of the loop is perpendicular to the
wire.
6. Reagents
6.1 Methyl Ethyl Ketone, conforming to the specifications of
the Committee on Analytical Reagents of the American Chemical Society.6
6.2 Store the solvent over anhydrous calcium sulfate (5
weight % of the solvent). Filter prior to use.
6.3 Air Supply, clean and filtered.
NOTE 3As an alternative, it is permissible to replace all references to
air used in the solvent evaporation process with nitrogen, provided the
nitrogen is clean and filtered. It should be noted, however, that the
precision statements for the test method were determined using air only
and that the precision associated with using nitrogen has not been
determined.

7. Sample
7.1 If the sample of wax is 1 kg (2 lb) or less, obtain a
representative portion by melting the entire sample and stirring
thoroughly. For samples over 1 kg (2 lb), exercise special care
to ensure obtaining a truly representative portion, bearing in
6
Reagent Chemicals, American Chemical Society Specifications, American
Chemical Society, Washington, DC. For Suggestions on the testing of reagents not
listed by the American Chemical Society, see Annual Standards for Laboratory
Chemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeia
and National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,
MD.

2Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

Temperature Range
37 to +21C
35 to +70F

D721 06 (2011)

All dimensions are in millimetres (inches)

FIG. 2 Cooling Bath

mind that the oil may not be distributed uniformly throughout

the sample, and that mechanical operations may express some
of the oil.
8. Procedure
8.1 Melt a representative portion of the sample, using a
water bath or oven maintained at 70 to 100C (158 to 212F).
As soon as the wax is completely melted, thoroughly mix.
Preheat the pipet or equivalent measuring device in order to
prevent the solidification of wax in the tip, and withdraw a
portion of the sample as soon as possible after the wax has
melted. The mass of wax transferred to the test tube must be
1.00 6 0.05 g. Allow the test tube to cool, and weigh to at least
the nearest 1 mg.
NOTE 4The weight of a test tube which is cleaned by means of
solvents will not vary to a significant extent. Therefore, a tare weight may
be obtained and used repeatedly.

8.2 Pipet 15 mL of methyl ethyl ketone into the test tube and
place the latter just up to the level of its contents in a hot water

or steam bath. Heat the solvent wax mixture, stirring up and

down with the wire stirrer, until a homogeneous solution is
obtained. Exercise care to avoid loss of solvent by prolonged
boiling.
NOTE 5Very high-melting wax samples may not form clear solutions.
Stir until the undissolved material is well dispersed as a fine cloud.

8.2.1 Plunge the test tube into an 800-mL beaker of ice

water and continue to stir until the contents are cold. Remove
the stirrer. Remove the test tube from the ice bath, wipe dry on
the outside with a cloth, and weigh to at least the nearest 0.1 g.
NOTE 6During this operation the loss of solvent through vaporizations should be less than 1%. The weight of the solvent is therefore
practically a constant, and after a few samples are weighed, this weight,
approximately 11.9 g, can be used as a constant factor.

8.3 Insert the temperature measuring device into the test

tube and place the test tube containing the wax-solvent slurry
in the cooling bath, which is maintained at 34.5 6 1.0C
(30.0 6 2.0F). During this chilling operation it is important

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

3Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT

D721 06 (2011)
2F), with the air jet centered inside the neck, and the tip 15 6
5 mm above the surface of the liquid. After the solvent has
evaporated, which usually takes less than 30 min, remove the
bottle and stopper, and place them near the balance. Allow to
stand for 10 min and weigh to the nearest 0.1 mg. Repeat the
evaporation procedure, using a 5-min evaporation period
instead of 30 min, until the loss between successive weighings
is not over 0.2 mg.
9. Calculation
9.1 Calculate the amount of oil in the wax as follows:
Oil in wax, weight % 5 ~100 AC/~BD!! 0.15

that stirring by means of the temperature measuring device be

almost continuous, in order to maintain a slurry of uniform
consistency as the wax precipitates. Do not allow the wax to set
up of the walls of cooling vessel nor permit any lumps of wax
crystals to form. Continue stirring until the temperature reaches
31.7 6 0.3C (25.0 6 0.5F).
8.4 Remove the temperature measuring device from the
tube and allow it to drain momentarily into the tube; then
immediately immerse in the mixture the clean dry filter stick
which has previously been cooled by placing it in a test tube
and holding at 34.5 6 1.0C (30.0 6 2.0F) in the cooling
bath for a minimum of 10 min. Seat the ground-glass joint of
the filter so as to make an airtight seal. Place an unstoppered
weighing bottle, previously weighed together with the glass
stopper to the nearest 0.1 mg, under the delivery nozzle of the
filtration assembly.
NOTE 7Take every precaution to ensure the accuracy of the weight of
the stoppered weighing bottle. Prior to determining this weight, rinse the
clean, dry weighing bottle and stopper with methyl ethyl ketone, wipe dry
on the outside with a cloth, and place in the evaporation assembly to dry
for about 5 min. Then remove the weighing bottle and stopper, place near
the balance, and allow to stand for 10 min prior to weighing. Stopper the
bottle during this cooling period. Once the weighing bottle and stopper
have been dried in the evaporation assembly, lift only with forceps. Take
care to remove and replace the glass stopper with a light touch.

8.5 Apply air pressure to the filtration assembly, and immediately collect about 4 mL of filtrate in the weighing bottle.
Release the air pressure to permit the liquid to drain back
slowly from the delivery nozzle. Remove the weighing bottle
immediately, and stopper and weigh to at least the nearest
10 mg without waiting for it to come to room temperature.
Unstopper the weighing bottle and place it under one of the jets
in the evaporation assembly maintained at 35 6 1C (95 6

Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

where:
A
= weight of oil residue, g,
B
= weight of wax sample, g,
C
= weight of solvent, g, obtained by subtracting weight
of test tube plus wax sample (8.1) from weight of
test tube and contents (8.2),
D
= weight of solvent evaporated, g, obtained by subtracting weight of weighing bottle plus oil residue
from weight of weighing bottle plus filtrate (8.5),
and
0.15 = average factor correcting for the solubility of wax in
the solvent at 32C (25F).
10. Report
10.1 Report the result as oil content, Test Method D721. If
the result is negative, report as zero.
11. Precision and Bias
11.1 PrecisionThe precision of this test method as determined by statistical examination of interlaboratory results is as
follows:
11.1.1 RepeatabilityThe difference between two test results, obtained by the same operator with the same apparatus
under constant operating conditions on identical test material,
would in the long run, in the normal and correct operation of
the test method, exceed the following values only in one case
in twenty:
0.06 1 8% of the mean

11.1.2 ReproducibilityThe difference between two single

and independent results obtained by different operators working in different laboratories on identical test material would, in
the long run, in the normal and correct operation of the test
method, exceed the following values only in one case in
twenty:
0.2 1 11% of the mean

11.2 BiasThe procedure in this test method has no bias

because the value of oil content can be defined only in terms of
a test method.
12. Keywords
12.1 oil content; petroleum wax; wax

4Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

All dimensions are in millimetres

FIG. 3 Air Pressure Regulator

(1)

D721 06 (2011)

All dimensions are in millimetres (inches)

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

FIG. 4 Evaporation Assembly

Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

5Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT

D721 06 (2011)
APPENDIX
(Nonmandatory Information)
X1. TEST METHOD FOR MEASUREMENT OF MAXIMUM PORE DIAMETER OF RIGID POROUS FILTERS

X1.1 Scope
X1.1.1 This test method covers the determination of the
acceptability of porous filter sticks used for filtration in Test
Method D721. This test method establishes the maximum pore
diameter and also provides a means of detecting and measuring
changes which occur form continued use.
X1.2 Definition
X1.2.1 maximum pore diameterthe diameter in micrometers of the largest opening in the filter.

X1.3 Summary of Test Method

X1.3.1 The filter is cleaned and wetted with water. It is then
immersed in water and air pressure is applied against its upper
surface until the first bubble of air passes through the filter. The
maximum pore diameter is calculated from the surface tension
of water and the applied pressure.
X1.4 Apparatus
X1.4.1 Pressure Measuring Device, mercury-filled manometer or equivalent, capable of measuring pressures in increments of 0.5 mm of Hg.
X1.4.2 Air Supply, clean and filtered.
X1.4.3 Air Pressure Regulator, needle-valve type.
X1.4.4 Drying Oven.
X1.5 Procedure
X1.5.1 Clean the filter sticks by soaking in concentrated
hydrochloric acid, and then wash them with distilled water.
Rinse with acetone, air dry, and place in drying oven at 220F
(105C) for 30 min.
X1.5.2 Thoroughly wet the clean filter to be tested by
soaking it in distilled water.
X1.5.3 Assemble the apparatus as shown in Fig. X1.1.
Apply pressure slowly from a source of clean air.

Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

FIG. X1.1 Assembly of Apparatus for Checking Pore Diameter or

Filter Sticks

X1.5.4 Immerse the filter just below the surface of the

water.
NOTE X1.2If a head of liquid exists above the surface of the filter, the
back pressure produced must be deducted from the observed pressure.

X1.5.5 Increase the air pressure to about 10 mm Hg (or

equivalent pressure value if using different units) below the
acceptable pressure limit and then at a slow uniform rate
equivalent to about 3 mm Hg/min until the first bubble passes
through the filter. This can be conveniently observed by
placing the beaker or test tube over a mirror. Read the pressure
measuring device when the first bubble passes off the underside
of the filter.
X1.6 Calculation
X1.6.1 Calculate the pore diameter as follows:
D 5 2180/p

where:
D = pore diameter, m, and
p = pressure reading, mm Hg.
NOTE X1.3From this equation, pressure corresponding to the upper
and lower limits of the specified pore diameters can be calculated. These
pressures may be used for acceptance testing.

6Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

NOTE X1.1It is recognized that the maximum pore diameter as

defined herein does not necessarily indicate the physical dimensions of the
largest pore in the filter. It is further recognized that the pores are highly
irregular in shape. Because of the irregularity in shape and other
phenomena characteristic of filtration, a filter may be expected to retain all
particles larger than the maximum pore diameter as defined and determined herein, and will generally retain particles which are much smaller
than the determined diameter.

D721 06 (2011)
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.

--```,,`,``,,,,,,,,```````,`,,``-`-`,,`,,`,`,,`---

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).

Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS

7Licensee=Occidental Oil & Gas/5910419104

Not for Resale, 07/04/2013 12:33:34 MDT