Tech Bulletin 0112 - Creaking Clicking of Frame

TECHNICAL BULLETIN
Bulletin No:
CDS. ref:
Issue:
Date:
MODEL/DERIVATIVE:
Freelander (LN)
0112
L8776bu
2
15.05.03
AFFECTED RANGE:
All derivatives
RE - ISSUE INFORMATION:
ACTION, PARTS INFORMATION and WARRANTY INFORMATION amended.
Please destroy your existing copy and replace with this Issue 2.
PROBLEM:
CLICKING / CREAKING NOISE FROM THE REAR UNDERSIDE OF THE VEHICLE
Apparent at slow speed when moving off in either 'forward' or 'reverse', and most
noticeable when using maximum steering lock.
CAUSE:
There are two possible causes for the above problem:
1. Movement between the tubular cross member and the jacking bracket on the
rear sub-frame.
NOTE: The new specification rear sub-frame has been fitted to vehicles from VIN
number 3A 243741.
2. The RH rear longitudinal may be cracked / fractured, and is most likely to occur
on vehicles that are subjected to a high number of stop / start journeys, engine
over-runs and hard acceleration in the following categories:
Fleet operators
Local authorities
Police
NOTE: The new specification RH rear longitudinal has been fitted to vehicles from
VIN number 2A 219766.
ACTION:
Where a complaint of the above is confirmed, follow procedure 1 to weld the tubular
cross member to the jacking bracket. If the clicking / creaking noise is still apparent
after carrying out procedure 1, then refer to procedure 2.
Procedure 1 - weld the rear sub-frame
1. Slowly drive the vehicle forward or reverse on full lock and listen for a clicking /
creaking noise coming from the rear underside of the vehicle. If a clicking /
creaking noise is evident, refer to the following steps.
TECHNICAL BULLETIN NO: 0112 ISSUE: 2
PAGE: 1 OF 8
ENGLISH
2. Raise the vehicle.

3. Clean off existing paint to expose bare
metal in preparation for welding (see
illustration 1).
4. Puddle weld both holes (inset in
illustration 1) to fix the tubular cross
member to the jacking bracket.
WARNING: Prepare for welding.
Protect the surrounding area such
as fuel lines and the petrol tank to
prevent the possible risk of fire or
explosion.
Health and Safety guidelines in
accordance with local market
requirements MUST be followed.
5. Etch prime bare metal, repair paint finish as required.

6. Slowly drive the vehicle forward or reverse on full lock and listen for a clicking /
creaking noise coming from the rear underside of the vehicle. If the clicking /
creaking noise is still evident, follow procedure 2 to check the longitudinals.
Procedure 2 - Check the RH rear longitudinal for cracks / fractures
1. Raise the vehicle on a lift.
2. Chock the front wheels.
3. Raise the rear of the vehicle and support on axle stands.
4. Using a transmission jack support the rear sub-frame.
5. Remove one rear sub-frame fixing bolt, re-fit and tighten bolt approximately 5
turns to secure the rear sub-frame.
6. Repeat step 5. for the remaining rear sub-frame fixing bolts.
7. Lower the rear sub-frame until it is supported on the fixing bolts.
8. Ensure that the mating surfaces of the rear sub-frame and the body
longitudinals are clean.
9. Inspect the rear longitudinals for cracks / fractures around the sub-frame
mounting points, if found follow rectification procedure 3.
NOTE: It has been established that only the RH rear longitudinal cracks / fractures.
This is due to the positioning of the differential in the sub-frame, where more load
is placed on the RH rear longitudinal.
10. Raise the rear sub-frame assembly.
11. Tighten the rear sub-frame bolts to 190 Nm (140 lbf.ft).
NOTE: If any of the rear sub-frame bolts are damaged or no resistance is felt when
tightening the bolts, then the bolts must be replaced.
12. Lower and remove the transmission jack.
13. Lower the vehicle and remove chocks from the wheels.
PAGE: 2 OF 8
ENGLISH
Procedure 3 - Replace the RH rear longitudinal

1. Disconnect the battery earth lead.
2. Disconnect the alternator multiplug.
3. Remove the exhaust system. Refer to Workshop Manual, part number LRL0350
(6th edition), Manifolds and exhausts, Exhaust pipe - rear, repair number
30.10.22.
4. Remove the rear bumper valance. Refer to Workshop Manual, part number
LRL0350 (6th edition), Exterior Fittings, Bumper Valance - rear, repair number
76.22.74.
5. Remove four nuts securing the bumper armature to the body and remove the
armature.
6. Remove the tail door. Refer to Workshop Manual, part number LRL0350 (6th
edition), Doors, Door - tail assembly - remove for access and refit, repair number
76.28.19/99.
7. Release the tail door aperture seal from lower part of the vehicle.
8. Remove both rear quarter lower trim casings. Refer to Workshop Manual, part
number LRL0350 (6th edition), Interior trim components, Trim Casing - rear
quarter - lower, repair number 76.13.12.
9. Remove the luggage compartment carpet. Refer to Workshop Manual, part
number LRL0350 (6th edition), Interior trim components, Carpet - luggage
compartment, repair number 76.49.04.
10. Remove the rear sub-frame for access. Refer to Workshop Manual, part number
th
LRL0350 (6 edition), Rear Suspension, Sub frame, repair number 64.35.78.
11. Remove the fuel tank. Refer to Workshop Manual, part number LRL0350 (6th
edition), Fuel system, Tank, repair number 19.55.01.
12. Remove 6 bolts securing the towing eye to the RH rear longitudinal and remove
the towing eye.
13. Release the wiring harness from the luggage compartment floor and position
aside.
14. Remove the RH rear damper assembly for access. Refer to Workshop Manual,
part number LRL0350 (6th edition), Rear suspension, Damper, repair number
64.30.02.
15. Remove 3 nuts securing the charcoal canister assembly to the body. Disconnect
3 multiplugs and 3 pipe connections, remove the charcoal canister from the
vehicle.
CAUTION: Before disconnecting or removing components, ensure the immediate
area around joint faces and connections are clean. Plug open connections to
prevent contamination.
16. Locate and drill out 18 spot welds on the new RH rear longitudinal (see
attachment 1, inset '1' illustration 1). Separate the front part of the RH
longitudinal ('A' in illustration 1) from the rear part of the RH rear longitudinal ('B'
in illustration 1) and discard the front part of the RH rear longitudinal ('A' in
illustration 1).
WARNING: Protect the surrounding area such as fuel lines and the petrol
tank to prevent the possible risk of fire or explosion.
Health and Safety guidelines in accordance with local market requirements
MUST be followed.
PAGE: 3 OF 8
ENGLISH
17. Straighten the flange faces as required on the new rear longitudinal.
18. Position bracket assembly, ALR7720 ('C' in illustration 1), inside the rear
longitudinal and mark its fitted position. Remove the bracket assembly from the
rear longitudinal.
19. Using an abrasive disk, remove the primer to expose bare metal on relevant
mating faces of the bracket assembly and the rear longitudinal.
20. Apply weld through primer to the bracket assembly and the longitudinal.
21. Position bracket assembly inside the rear longitudinal and weld into position
(see inset '2' in illustration 1).
NOTE: Align the fixing hole in the bracket with the fixing hole in the longitudinal
prior to welding.
22. Locate and drill out all spot welds securing the RH rear longitudinal to the floor
and the rear crossmember (see attachment 2, illustration 2).
23. Locate and remove with an abrasive disk, 10 MIG welds securing the rear
longitudinal to the inner and outer quarter reinforcement panels.
24. Carefully remove the rear longitudinal, avoid damaging the quarter inner
assembly when releasing the damaged longitudinal.
NOTE: Part of the RH rear longitudinal is secured using metal to metal adhesive.
25. Using an abrasive disk, clean the spot weld sites and remove primer.
26. Mark the weld positions on the replacement panel. Punch or drill 8 mm diameter
spot holes at the weld sites.
27. Apply weld through primer and metal to metal adhesive to relevant surfaces.
28. Align and support the rear longitudinal in its fitted position to the body.
WARNING: Prepare for welding. Protect the surrounding area such as fuel
lines and the petrol tank to prevent the possible risk of fire or explosion.
Health and Safety guidelines in accordance with local market requirements
MUST be followed.
29. Weld the replacement RH rear longitudinal to the body, stagger welds to keep
distortion to a minimum.
30. MIG weld the inner and outer quarter reinforcement panels to the rear
longitudinal in 10 places 20 mm long.
31. Clean the weld site, remove all traces of weld spatter.
32. Etch prime bare metal, repair paint finish as required.
33. Prepare the panel and seal against corrosion.
34. Inject cavity wax into the RH rear longitudinal to prevent corrosion.
th
35. Fit the fuel tank. Refer to Workshop Manual, part number LRL0350 (6 edition),
Fuel system, Tank, repair number 19.55.01.
36. Fit the rear sub-frame. Refer to Workshop Manual, part number LRL0350 (6th
edition), Rear Suspension, Sub frame, repair number 64.35.78.
NOTE: Do not refit wheel arch liner at this stage.
37. Fit the charcoal canister assembly and secure with nuts.
38. Connect multiplugs and pipes to the charcoal canister assembly.
39. Fit the RH rear damper assembly. Refer to Workshop Manual, part number
LRL0350 (6th edition), Rear suspension, Damper, repair number 64.30.02.
PAGE: 4 OF 8
ENGLISH
40. Fit the RH rear wheel arch liner. Refer to Workshop Manual, part number
th
LRL0350 (6 edition), Exterior fittings, Liner - rear wheel arch, repair number
76.10.49.
th
41. Fit the exhaust system. Refer to Workshop Manual, part number LRL0350 (6
edition), Manifolds and exhausts, Exhaust pipe - rear, repair number 30.10.22
42. Fit the towing eye to the RH rear longitudinal fit bolts and tighten to 45 Nm (33
lbf.ft).
43. Etch prime bare metal, repair paint finish on the luggage compartment floor as
required.
44. Position the wiring harness to the luggage floor.
45. Fit the luggage compartment carpet. Refer to Workshop Manual, part number
LRL0350 (6th edition), Interior trim components, Carpet - luggage compartment,
repair number 76.49.04.
46. Fit the rear quarter lower trim casings. Refer to Workshop Manual, part number
LRL0350 (6th edition), Interior trim components, Trim Casing - rear quarter lower, repair number 76.13.12.
47. Fit the tail door aperture seal.
48. Fit the tail door. Refer to Workshop Manual, part number LRL0350 (6th edition),
Doors, Door - tail assembly - remove for access and refit, repair number
76.28.19/99.
49. Position bumper armature to body, fit nuts and tighten to 30 Nm (22 lbf.ft).
50. Fit the rear bumper valance. Refer to Workshop Manual, part number LRL0350
(6th edition), Exterior Fittings, Bumper Valance - rear, repair number 76.22.74.
51. Connect the alternator multiplug.
52. Connect the battery earth lead.
PARTS INFORMATION:
AFE490500 - RH rear longitudinal
ANR5335 - Sub-frame fixing bolts (as required) - 4 off
ALR7720 - Bracket assembly - rear sub-frame - mounting rear - RH
WARRANTY CLAIMS:
Procedure 1
Use Complaint Code: 5A0K
Use S.R.O.: 51.25.89/27 - weld rear sub-frame
Time allowance: 0.40 Hrs
Procedure 2
Use Complaint Code: 9K1K
Use S.R.O.: 64.35.89/33 - Check chassis longitudinal for cracks
PAGE: 5 OF 8
ENGLISH
Procedure 3
Use Complaint Code: 9K1E
Use S.R.O.: 77.70.89/26 - replace RH chassis longitudinal
PAGE: 6 OF 8
ENGLISH
Attachment 1
Illustration shows:
Supplied condition of the RH rear longitudinal

Position of spot welds to be removed
Final panel condition
Position of the rear mounting bracket assembly (supplied
separately)
PAGE: 7 OF 8
ENGLISH
Attachment 2
Illustration shows the position of welds securing the RH rear longitudinal
PAGE: 8 OF 8
ENGLISH

Tech Bulletin 0112 - Creaking Clicking of Frame

Uploaded by

Copyright:

Available Formats

Tech Bulletin 0112 - Creaking Clicking of Frame

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tech Bulletin 0112 - Creaking Clicking of Frame

Uploaded by

Copyright:

Available Formats

What are the possible causes of clicking/creaking noise from the rear underside of the vehicle?

What are the two procedures to diagnose and fix the issue?

TECHNICAL BULLETIN

2. Raise the vehicle.

5. Etch prime bare metal, repair paint finish as required.

TECHNICAL BULLETIN NO: 0112 ISSUE: 2

Procedure 3 - Replace the RH rear longitudinal

TECHNICAL BULLETIN NO: 0112 ISSUE: 2

TECHNICAL BULLETIN NO: 0112 ISSUE: 2

TECHNICAL BULLETIN NO: 0112 ISSUE: 2

Supplied condition of the RH rear longitudinal

TECHNICAL BULLETIN NO: 0112 ISSUE: 2

Illustration shows the position of welds securing the RH rear longitudinal

TECHNICAL BULLETIN NO: 0112 ISSUE: 2

You might also like