RMPrepUSB

Please visit the home website for the latest version and lots of tutorials:

http://sites.google.com/site/rmprepusb
v2.1.625 and later

Introduction
RMPrepUSB is a Windows utility that can be used to format any USB storage device,
e.g. USB Flash drive (UFD) or USB hard disk, as a bootable device (but cannot be
used on USB Floppy drives). It can be used to partition, format, write a Master Boot
Record, partition table and/or Volume Boot Record (sometimes called a Partition
Boot Record) and operating system boot code to a storage device (e.g. USB flash
memory drive or USB hard disk). It can also be used on non-USB drives.
If you installed RMPrepUSB using the Installer, you can easily uninstall it using the
uninstall RMPrepUSB entry in the Start Menu. However, you do not need to install
RMPrepUSB (it is portable and will even run under BartPE or WinPE v1/v2/v3), just
ensure that all the files are copied to a folder on your hard drive or storage drive.
Note: if running Win PE you may need to copy the MSVBSM60.DLL from the
WINPE_EXTRA folder to the same folder that RMPrepUSB.exe is in. Also, if you
are running under Win PE v1/BartPE you may need to copy showdrive.exe file from
the WINPE_EXTRA folder (do not copy this file if running Windows XP+ though as
it can cause problems!).
To start - select the Language that you want to use in the top-right hand box.
RMPrepUSB will list all *.INI files found in the .\LANG folder. Note that the
translated files may be slightly out of date, but if you select English you will always
get the latest version of help text. If you have XP, you may need to install Asian
language support (see FAQ Q32)
Please read the all the FAQs at the end of this document!
LICENCE SMALL PRINT
RMPrepUSB and RMPartUSB are free (Freeware) for private use only; however they are not Open Source programs. For
commercial use and licensing please contact [email protected]. Distribution, sale, or use in a commercial solution is forbidden
without permission from RM Education plc (see FAQs below for more information).
The RMPrepUSB download includes some executables which are not the intellectual property of the author or RM Education.
The licensing terms and conditions for these programs are:
Grubinst.exe, grldr and touchdrv.exe Author: bean123 homepage GPL (see GPL.txt)
Mkefs.exe Author: MattWu [email protected] homepage GPL (see GPL.txt)
Syslinux.exe Author: H. Peter Anvin see homepage
QEMU - QEMU was written by Fabrice Bellard and is free open-source software.
Various parts are released under different GNU General Public License version 2-compatible licenses.
These include the GNU Lesser General Public License (GNU LGPL) or permissive licenses such as the BSD license

RMPrepUSB is intended for use on USB Flash memory drive, USB hard disk drives
or other USB storage devices such as card readers. It can also be used on any nonUSB disk if the special command line parameter ALLDRIVES is used or if Alt+F5 is
pressed.

RMPrepUSB can:
Partition, format and make bootable a USB drive (follow the steps numbered
1-6 in blue text)
Clean (erase/wipe) a USB drive (best to unplug and re-plug afterwards)
Backup a USB drive (or parts of a USB drive) to an image file
Restore an image file (or part of an image file) to a USB drive
Install the grub4dos or syslinux bootloader onto a USB drive
Test a USB drive (useful for testing fake USB flash memory drives)
Test raw read/write speed of a USB drive
Eject a USB drive (for safe removal)
Display the partition structure of a USB drive (or image file)
Be used after PEBuilder to install your XP PE files to a bootable USB drive.
Work on hard disk drives as well as USB drives (by using the Alt+F5
ALLDRIVES toggle key)
Create an ext2 read/write filesystem (as a mountable file e.g. casper-rw)
Emulate booting from the selected USB drive (QEMU = F11)

Note: Red or blue coloured buttons will write to your USB drive in some way. All
red/blue buttons will erase, alter or overwrite your drive contents. If you have any
important files on the drive, copy them to a safe place first!
Important: always run these utilities with Administrator privileges or the drive
may not be accessible or you may get a write error reported!

When you click on one of the Prepare Drive, Quick Size Test, Test Speed, Clean,
Image Tool or Info buttons, RMPrepUSB will call the Windows command line utility
RMPartUSB - the exact command line will be shown to the user beforehand. If you
prefer, you can use RMPartUSB in your scripts or batch files rather than use
RMPrepUSB. Type RMPartUSB in a Windows command shell to see full
instructions on how to use the utility or read the rmpartusb.txt readme file.
Note: The button 6 Prepare Drive uses the settings numbered 1-5. The two imaging
operation buttons (FiletoUSB and USBtoFile) are totally independent of any other
settings within RMPrepUSB (i.e. the NTLDR, FAT32 and all other options have no
affect when imaging a binary image is simply copied to or read from the UFD and is
similar to the dd.exe utility, no additional tweaking is done by RMPrepUSB or
RMPartUSB and no extra files are copied afterwards). The Install grub4dos
function installs grub4dos to any drive and does not call RMPartUSB.

RMPrepUSB Help form (press F1 or Help button)

RMPrepUSB videos on YouTube

See my YouTube videos at: http://sites.google.com/site/rmprepusb/tutorials/video-tutorials

Six steps (1-6) to make your USB drive bootable

1. Select the USB drive in the listbox if more than one is present and either
leave the 1 Partition Size as MAX or change it (e.g. type 512 for a partition
size of 512MiB).
2. Change the 2 Volume label text if you want to.
3. Set the 3 Bootloader Options that you want installed onto the new partition
after it has been formatted.
4. Change the 4 Filesystem and Overrides. You may need to experiment with
these before you can find a combination that works. If in doubt use FAT32
and Boot as HDD.
5. If you want to, you can copy the contents of a folder to the new empty
partition on the USB drive after it has been formatted by RMPrepUSB. Tick
the 5 COPY OS FILES box if you want to do this. Note: RMPrepUSB will
not place any boot files on the USB drive and it will not be bootable unless
you copy some boot files onto it.
6. Click on the blue 6 Prepare Drive button.
WARNING: After a format operation or if Refresh is clicked, RMPrepUSB
may select a different drive in the drop-down list. ALWAYS check that the
correct USB drive is selected before clicking the Prepare button!
Note: When finished and before you unplug the USB drive, click on the Eject
button to prevent file corruption.
If you are experiencing difficulties using RMPartUSB or RMPrepUSB when
formatting drives as a floppy device try disabling your antivirus software. Some
antivirus software (e.g. Symantec) can interfere with direct access to the drive once it
has been formatted as a floppy drive!
Special shortcut keys:
F1 Help
F2 Explorer: USB drive
F3 Explorer: RMPrepUSB application home folder
F4 Open menu.lst from root folder on currently selected USB drive with notepad
F5 Refresh (Alt+F5 will also change the ALLDRIVES mode)
F6 Open USBSpeedDP.csv using the spreadsheet app. associated with .csv files
F7 Open USBSpeed.csv using the spreadsheet app. associated with .csv files
F8 Open USBSpeedDP.csv in notepad
F9 Open RMPrepUSB.ini file in notepad
F10 Save current configuration settings to RMPrepUSB.ini
F11 Run QEMU and emulate booting from USB drive
F12 Load user pre-set menu again (if RMPrepUSB.ini file present)
Tip: Press F1 to see this hotkey list and then press ESC to close the help form.

About the COPY OS FILES option

RMPrepUSB prepares a USB drive by calling RMPartUSB which partitions it,
formats it and places boot code in the Master Boot Record (MBR) and Volume Boot
Record (VBR, sometimes called the Partition Boot Record or PBR). However, the

USB drive will not boot unless you also copy the required Operating System boot
files onto the drive. You can automatically copy files to the USB drive after it has
been formatted by ticking the COPY OS FILES option. If you do not tick this option
then you must manually copy any boot files onto the USB drive after the drive has
been formatted - just make sure you copy the system and hidden files too!
If you are installing linux (e.g. Ubuntu or YLMF) and want an ext2 filesystem (e.g. a
casper-rw volume), you should create a file of the same name using the Create Ext2
FS button.

Saving your favourite configurations

If you regularly make bootable USB drives or you want to distribute RMPrepUSB to
other users inside your company or to friends, together with a source folder containing
your OS files, you can save the RMPrepUSB settings to RMPrepUSB.ini
automatically by pressing F10. Here is how to do it:
A. Place your source OS files in folders on the C: drive of your hard disk, e.g.
C:\ACME\RMPrepUSB\SourceFiles\OS2.4
C:\ACME\RMPrepUSB\SourceFiles\OS2.7
Now for each USB configuration:
B. Run RMPrepUSB (you must click cancel if you already have an RMPrepUSB.ini
file present and are prompted to choose a previous configuration) and actually make
your bootable USB drive as you would normally (you do not have to do this, unless
you use syslinux or grub4dos, but it helps to get it right - if you don't actually make a
USB drive then check the contents of the RMPrepUSB.ini file after making it). If you
need to use the install syslinux or grub4dos options, you must run through a complete
format operation to set the correct Raid/Syslinux or grub4dos options so they are
saved to the ini file correctly when you later press F10.
C. (optional) After 'Prepare Drive' has finished and the file copy has completed,
untick the No user prompts box and then click on Install grub4dos and choose the
grub4dos options as you require (this sets the grub4dos option to either MBR or PBR
depending on which one you choose). If you don't need to run grub4dos, then skip this
bit as it is not necessary. If you also want to create an ext2 filesystem, you should
use the Create ext2 FS button to set those options (though you can cancel after
entering the volume name and size parameters). Now you can tick the No user
prompts box again if you dont want the end user to have lots of prompts.
D. Now press F10 - you should be asked if you want to append the settings to the
configuration file RMPrepUSB.ini. F10 records all the current settings including the
MBR or PBR selection used when grub4dos was run, syslinux options and also the
ext2 filename/size and appends them to the end of the RMPrepUSB.ini file.

E. You will be asked to input a title (which will eventually appear in the users menu
see section F below) and then add the users instructions:

If you don't already have an RMPrepUSB.ini file then it will be created for you. You
can press F9 if you want to see the ini file or edit it.
Repeat this (B-E) for all your different types of bootable OS's.
F. Exit from RMPrepUSB and then restart RMPrepUSB - because an INI file is now
present in the same folder as RMPrepUSB.exe, the user will now see a menu list

when RMPrepUSB first runs and can pick one of the preset configurations, as shown
below:

Clicking Cancel will not set any options, but choosing a configuration and clicking
OK will pre-set the options. The user will now be prompted with the instructions that
you previously entered into the configuration file, e.g.:

G. When the user clicks on the 6 Prepare Drive button, they will be prompted to
accept or refuse the SIZE and VOLUME LABEL that was set in the configuration
file:

If the user chooses No then the current volume label and partition size settings in
RMPrepUSB will be used; Cancel will abort the operation. If you used Install

grub4dos and/or the Create ext2 FS button, it will automatically run with the
correct options that you recorded in the RMPrepUSB.ini file.
You can edit the INI file using Notepad to make changes or delete any section just
press F9. Note that you can hide some buttons and checkboxes if you wish. Here is an
example RMPrepUSB.ini file with only one menu item:
TITLE=Ylmf Live USB
SIZE=MAX
LABEL=Ylmf 3.0
OS=MSDOS
FILESYSTEM=FAT32
BOOT_AS=HDD
USE64HD_32SEC=FALSE
FORCE_LBA=FALSE
COPYFILES=TRUE
COPYFOLDER=.\Ylmf
BARTPE=FALSE
SUPPRESSPROMPTS=FALSE
BOOTABLE=TRUE
GRUB4DOS=MBR
USERPROMPT=Click 6 Prepare Drive to format your USB drive, install grub4dos and create
an Ext2filesystem named casper-rw for Ylmf
SYSLINUX_OPT=
EXT2FNAME=casper-rw
EXT2FSIZE=1000
GRUBVISIBLE=FALSE
EXT2VISIBLE=FALSE
SYSLINUXVISIBLE=FALSE
INACTIVEVISIBLE=FALSE
BARTPEVISIBLE=FALSE
IMAGETOOLSVISIBLE=TRUE
SPEEDTESTVISIBLE=FALSE
SIZETESTVISIBLE=FALSE
CLEANVISIBLE=TRUE
QEMUVISIBLE=TRUE

You can now ZIP up all source files and RMPrepUSB files and create a selfextracting EXE which will extract the source files to the correct location on the hard
disk (i.e. C:\ACME\RMPrepUSB in this case). This is especially useful if you have
the same source files but have different systems which need different RMPrepUSB
options set (i.e. some systems boot with Force LBA set and some do not - so you can
have two configurations but only one set of source files). Alternatively, you can
create a self-installing distribution file using NSI see the tutorial on the website for
more details.
Note: if your partition is small (e.g. DOS), rather than use preset configurations, you
can also distribute an image instead, using the 'USB->File' function (make sure the
USB partition size is as small as possible - just big enough to hold the OS files to keep
the image size small) and use the PALL option.

How to boot to an Operating System

RMPartUSB only partitions and formats the drive. You must copy over the boot files
to make a bootable disk. RMPrepUSB can copy these boot files to the USB drive if
you use the Choose Copy Folder button and tick the Copy OS Files check box.
Hint: if the boot files are present but your PC is not booting correctly - check your
BIOS setup menu options! Some BIOSes have an option to boot a USB drive as a
Fixed Disk or a Removable Disk. Try different BIOS settings if you are having
difficulty getting your USB drive to boot!
Here are some quick tips on what boot files you may need to boot different Operating
Systems:

Required extra boot files

MS-DOS requires IO.SYS (or MSDOS.SYS depending on the version used) and
COMMAND.COM in order to boot. You must obtain these files from somewhere
(e.g. a DOS floppy boot diskette?). Simply copy these files onto the USB drive
after you have formatted it using the MS-DOS option, by using the COPY FILES
option to point to where you keep these MS-DOS boot files and tick the Copy
checkbox.
FreeDOS requires the files KERNEL.SYS and COMMAND.COM in order to boot.
The latest version of RMPrepUSB includes the few essential boot files in a
FreeDos folder, so simply use the COPY FILES option and select the FreeDOS
option in RMPrepUSB.
WinPE v1 and XP require many files to boot, but the first file is NTLDR. If you
want to boot to BartPE, see Q24 below.
WinPE v2 and v3 and Vista and Windows 7 require many files to boot, but the first
file is BOOTMGR. For instance, just copy all files from a Vista or Windows 7
bootable DVD to the USB drive after setting the WinPEv2 (bootmgr) option in
RMPrepUSB.
SysLinux when booting will first look for the files LDLINUX.SYS and a
SYSLINUX.CFG file. Many other files will also be required. If you are using
isolinux, use the Install SysLinux RMPrepUSB option and then after the files
have been copied over, rename isolinux.cfg to syslinux.cfg
Grub4dos when booting will first look for the file GRLDR. RMPrepUSB will ask
you if you want it to copy this file after it has installed the boot code. After that it
will look for a \menu.lst file. Note that the version of grubinst.exe is not the
normal v1.1 version, it is a homebrew version (I have called in v1.2) which has
been specially modified to work on more systems/BIOSes than the old 1.1
version. The grldr file is recent chenall/tinybit version but you can change it for
any version you like by overwriting the file.
If you want to use a different version of syslinux or grub4dos, place your own
versions of syslinux.exe, (grubinst.exe) and grldr into the same folder as RMPrepUSB
and overwrite the ones provided. Some older versions are contained within the
RMPrepUSB folder after installation, for your convenience.

Explanation of the Override options

The most complex part of RMPrepUSB is in selecting which overrides (if any) to use.
The reason that there are so many choices is that different BIOSes behave in different
ways. A USB Flash Drive (UFD) that is formatted using the Boot as HDD (2PTNS)
option and containing MS-DOS boot file may boot as an A: drive on one system, but
boot as a C: drive on another system. If you change the BIOS Setup menu options on
the same system, it might then boot as an A: drive. On yet a third system, the same
USB flash drive might not boot at all!
In addition, some BIOSes will not boot from a UFD at all if the physical drive size is
greater than 512MB or some BIOSes may not boot from a UFD if the volume size
is over (say) 1.3GB. DOS will not boot if the drive is over 137GB.
If you wish to boot from a UFD or USB hard drive, you may need to experiment with
the settings below. You may find that one group of settings will work for one system
and a different group of settings will work for another system. If using UFDs, always
try a 512MB USB flash drive first before you move on to larger UFDs some older
BIOSes will only work with small UFDs.
Boot as FDD (A: no MBR)
This option will format the drive with the chosen filesystem format option
(FAT16\FAT32 or NTFS FAT12 as used on floppy disks is NOT supported) - the
USB drive will have no partition table just like a floppy disk. The first sector of the
USB drive will typically contain the operating system boot code. This option is
usually used for an MS-DOS or FreeDOS drive that you wish to boot as a large floppy
drive (i.e. they will boot to the A: prompt). Normally FAT16 is used for this.
You can also select the 64hd/32sec option (recommended). If you de-select this
option then the volume boot record will use 255 heads and 63 sectors per track.
Note: If you need to always boot as drive A:, grub4dos can be used to map the UFD
as drive A: even if the BIOS tries to boot it as a hard disk. See FAQ 35.
Boot as ZIP (A: with MBR)
This option creates a Master Boot Record and partition table in the first sector of the
drive. The Volume Boot Record code that is written to the drive will be suitable for
booting MS-DOS or FreeDOS as a floppy drive. In addition, a drive geometry of
64hd\32sectors will be used (if possible). If you wish to boot the USB drive as a hard
drive then untick this option or tick the 64hd\32sec option.
Force use of LBA calls can be used with this override, but ticking the 64hd/32sec
override will de-select the ZIP option, as the ZIP option will add the 64hd\32sec
override.
Note: Some ZIP drive specifications define the first three entries in the partition table
as unused and the fourth partition table entry is used, however this partition
arrangement is not recognised by Windows and such a partition cannot be accessed by
Windows Explorer. Only the first partition of a removable drive can be accessed by
Windows OSs (unless a special driver is installed).

Boot as HDD (C: 2PTNS)

This option simply adds a second, small hidden partition entry to the partition table.
Some BIOSes will treat a USB drive as a hard disk if it sees more than one partition
table, because the specification of a ZIP drive (super-floppy) is that it must only
have one partition (thanks to online of www.boot-land.net for this discovery). If you
want to boot a system from a USB drive as a hard disk, set this option and untick the
ZIP option. You can try either the Force LBA override or the 64hd\32sec override
with this option.
Note: If you want to boot a USB drive as a hard disk and this option does not appear
to work, try re-partitioning again but leave all the USB-FDD, USB-ZIP and USBHDD options unticked.
Forcing the use of LBA calls (only use if boot problems)
This option sets the end Cylinder/Head/Sector values in the partition table to their
maximum value of 1023 (3FEh) cylinders, 255 heads (FEh) and 63 sectors even if
the partition size is under 8GB. If BIOSes read a drive partition table and see that the
CHS value is the maximum, then the BIOS may use a sector translation of 255 heads
and 63 sectors per track. In addition, partition and volume boot record boot code will
use LBA Extended Int 13h BIOS calls if it determines that the CHS values are set to
the maximum. This also may help to successfully boot an operating system from a
USB drive.
This option cannot be used with the 64hd\32sec option as they are mutually exclusive.
Use 64hd/32sec if possible
Instead of creating a partition table using the default drive geometry of 255 heads and
63 sectors per track, this option will use 64 heads and 32 sectors per track which is the
most compatible setting for USB-ZIP (large-floppy) booting. If the partition is too
large to use 64\32 geometry, then 128\32 will be used instead and then 255/32 and
then 255/63. This option is recommended for ZIP (large floppy) booting and FAT16.

BartPE to USB
This tick box should be used if you want to boot an XP/WinPE v1 based OS such as
BartPE from a USB drive. It can be used to prepare PeBuilder BartPE files or other
XP-based boot CD files such as those used on Asus EeePC XP Recovery DVDs. You
can only tick this box if you have selected the XP booot option and have also ticked
the COPY OS FILES tick box.
Function: After RMPrepUSB has partioned and formatted the USB drive, it will copy
over the files in the COPY OS FILES folder and then run the RMPrepUSBXP.cmd
script file (or the rmprepusbxp_german.cmd file if the german language is selected).
This script performs a similar task to petousb.cmd, on the USB drive only it...
1. Copies \i386\setupldr.bin to \NTLDR
2. Copies \i386\NTDETECT.COM to \NTDETECT.COM
3. Renames the \i386 folder on the USB drive to \MININT
4. Copies all files and folders in the RMPrepUSB folder PEtoUSB from your hard
disk to the root of the USB drive (this folder is normally empty unless you copy extra
files to it first).

A typical usage would be to use PeBuilder and set the Builder source to your XP SP2
or SP3 install CD and the Builder output to BartPE and the Media Output to None
and then press the Build button. After the build has finished, copy any extra files you
want to add to the USB drive (e.g. portable apps) to the PEtoUSB folder which is in
the RMPrepUSB folder on your hard disk (optional) and then use RMPrepUSB and
set the COPY OS FILES folder to the BartPEISO folder path (e.g.
C:\pebuilder3110a\BartPE) and tick the XP, NTFS and BartPE options. This should
make a BartPE bootable USB drive.
For a tutorial on how to create an Asus EeePC bootable flash memory drive see
http://www.youtube.com/watch?v=4qMsMXOterc

Using RMPrepUSB on a non-USB disk

You must run RMPrepUSB using the command line RMPrepUSB ALLDRIVES
which must run with Administrator privileges. Alternatively, you can type Alt+F5 to
toggle between ALLDRIVES mode and USB only. In ALLDRIVES mode,
RMPrepUSB will then list all drives rather than just the USB drives. You could save
your hard disk MBR using USB->File in this way or install grub4dos or the Syslinux
bootloader.
WARNING: Do not accidentally wipe the wrong hard disk!
This may be useful if you want to prepare a 2nd hard disk as a bootable drive (e.g.
160GB FAT32 + grub4dos). In this case you should use CLEAN to remove all
partitions first so that Windows does not lock it.

Recommended settings
FreeDOS and MS-DOS boot as A:
Size=500 Boot.as.FDD 64hd\32sec FAT16
Size=500 Boot.as.ZIP 64hd\32sec FAT16
If either of these work, then try using MAX size and/or FAT32
Ensure the BIOS boot option for USB is set to Removable Drive and not Fixed
Disk
BartPE, WinPEv2\v3, FreeDOS and MSDOS boot as C:
Size=500 Boot.as.HDD.
FAT16
Size=MAX Boot.as.HDD.(2PTNS) FAT32
Ensure the BIOS boot option for USB is set to Fixed Disk and not Removable
Drive. Try also various combinations of these options. Note that one setting may
work for one computer but not for a different computer! Try adding the ForceLBA
option if you have difficulty booting.
Testing your BIOS (experts only not in the Lite version)
Some special MBR files are provided in the TESTMBR folder. These allow you to
test how your BIOS sees a USB drive when you change various options in

RMPrepUSB. Please read the ReadMe.txt file in the TESTMBR folder for more
details.

Tip for UFD booting as a hard drive:

If you have a Lexar or Netac USB Flash drive, obtain the utility BootIt.exe (try a
Google search). This utility has a Flip Removable Bit button click on this and then
unplug the UFD, then plug it in again if it has worked, your UFD will be classified
as a Fixed Disk rather than Removable Media. The utility only works with certain
types of UFD controller chips. Many BIOSes will always boot a drive as C: (hard
disk) if the device identifies itself as a Fixed Disk rather than Removable Media.
You can also create and access multiple partitions on the USB drive under Windows
when it is seen as a Fixed Disk type.

Booting linux
To boot a linux system, use the SYSLINUX option in RMPrepUSB. This will format
the UFD as a FAT16 or FAT32 MSDOS volume and then (after copying files if you
tick the file copy option) will run syslinux.exe on the new UFD volume. The
Windows version of syslinux.exe must be in the same folder as RMPrepUSB.exe.
Syslinux.exe will install syslinux boot code into the volume specified and place the
file ldlinux.sys on the UFD. Do not delete, overwrite or move this file once syslinux
has placed it on the UFD or the UFD may not boot it must remain at the same sector
position on the UFD. If you already use syslinux.exe, replace the version in the
RMPrepUSB folder with your version to avoid compatibility issues.
When the UFD boots, it will load ldlinux.sys and look for a syslinux.cfg file, which
can contain a menu and details of which kernel to load. If you have an isolinux.cfg
file, you need to rename this to syslinux.cfg. More information can be found on the
internet about syslinux.
If the UFD fails to boot after a while, either re-format the UFD using RMPrepUSB
again or run syslinux.exe from the Windows command line (cmd) e.g.
syslinux fma F: (where F: is the volume letter of the UFD)
WARNING: take care not to specify your hard disk drive letter or your hard disk will
not boot to Windows!
If you install a version of linux that supports a persistent mode onto your USB drive,
you can use the Create ext2 FS button to create an ext2 filesystem as a file on the
USB drive. Typically, for Ubuntu based versions it will be named casper-rw, and be
in the root and have a size of at least 1GB.

Installing the Grub bootloader

The Install grub4dos button will run grubinst on the selected USB drive and then
ask the user if they wish to also copy the grldr file. The USB drive should be already
partitioned and formatted before you click this button. If the grub MBR does not seem
to be written to the USB drive (because it does not seem to load grub but boots to
DOS) then try the Eject button before you click on the Install grub4dos button (but

you will have to copy over the grldr file manually after re-inserting the USB drive).
You will be given the choice of installing grub4dos as an MBR or a PBR. MBR will
usually work for most systems, but if you have problems (e.g. flashing cursor) try
PBR instead.
A guide on how to use grub4dos is here or there is also a tutorial here.
To test the USB drive and your grub4dos menu, press F11 to run the QEMU
emulator.

Explanation of how BIOSes boot from a USB device

Most BIOSes require the user to enable USB booting and set the boot order so that a
USB device will boot before the internal hard disk (although some BIOSes have an
F10, [ESC] or F12 key function which will allow you to choose a boot device from a
BBS menu). In addition you can often set the USB speed to USB 1.1 speeds (Hi
speed) or USB 2.0 speeds (Full speed). If you are having difficulty booting from a
USB drive, it is recommended to use a rear USB port, set the BIOS to USB 1.1 speeds
and change the boot order so that the USB drive is first in the boot menu.
Before you enter the BIOS menu, switch off the system, insert the USB drive and
then switch on the system then press the F1 or F2 or Esc or DEL key (depending on
your particular system) to enter the BIOS Setup menu. Note: it is highly
recommended that you always switch on the system with the UFD already
connected; some BIOSes do not list the UFD or provide menu options unless the
UFD is already inserted. In addition, some BIOSes only determine the type of UFD
that is connected on the first cold boot, so if you re-format the UFD using a different
RMPrepUSB option and then re-connect it to the target system, it will not treat the
UFD as a different device type (e.g. USB-ZIP instead of USB-HDD) unless you first
switch off the target system and then switch it on again.
All BIOSes behave differently, however disk storage devices are always accessed via
Interrupt 13h calls to the BIOS. There are two types of ways to access a disk device
via the BIOS floppy or hard disk read or writes. The BIOS must determine
whether to allow access to the USB drive that it detects as either a floppy (which is
accessed with Int 13h DL=00h, or 01h for the 2nd floppy drive, etc.) or a hard disk
(which is accessed with Int 13h DL=80h, or 81h for the 2nd drive, etc.). The BIOS has
to determine which of these two access methods (DL=0 or DL=80h) to map the
USB drive to.
Once a BIOS determines how to map the USB device (either as a floppy device or a
hard disk device), it will read the first sector from the USB device (512 bytes) into
memory at address 07C0:0000h and then jump to that code. The last two bytes of the
sector must end in the two bytes 55h and AAh or it is not considered to be valid
boot code. When the CPU starts to execute the code that has just been copied into
memory at 07C0:0000h, the BIOS has also pre-set the DL CPU register to the correct
device number (usually either 00h or 80h). The boot code can use this value in DL to
load more sectors into memory from the same USB device.

There are two types of USB drives Fixed or Removable. The type is reported by the
USB controller when interogated by the BIOS.
There are three types of USB drive formats and the BIOS must try to determine
which of the three different ways to access the USB drive:
1. USB-FDD (floppy disk device)
The BIOS maps the device to floppy Int 13h DL=0. A USB device may be
detected as a USB-FDD device if it has a device name similar to TEAC floppy
drive and a capacity of 1.44MB, or possibly if it has no valid partition table. The
device does not need to be formatted as 1.44MB, you can have a 1GB FAT16
UFD with no MBR.
2. USB-HDD (hard disk device)
A BIOS maps the device to hard disk Int 13h DL=80h. A USB device may be
treated as a USB-HDD device by the BIOS if it has a partition table and has more
than one partition entry in that partition table. If only one entry exists the BIOS
could treat the device as a USB-ZIP drive or a USB-HDD drive. Sometimes a
BIOS menu setting can be changed to alter this behaviour. If the USB hardware
device type is reported as a Fixed Disk type by the USB device controller chip,
then most BIOSes will always treat that USB device as a hard disk and use
DL=80h.
3. USB-ZIP (pseudo-super-floppy)
A BIOS maps the device to floppy Int 13h DL=0. A USB device may be
detected as a USB-ZIP device if the drive has a partition table containing only one
entry. The BIOS may also require the device to be under a certain size (e.g.
512MB or less) or have values in the partition table of 64hds\32secs.
In addition, when a BIOS boots from a device as a USB-ZIP device it does NOT
load the first sector MBR code (LBA 0) into memory instead the BIOS loads the
Volume Boot Record code directly into memory and jumps to it by reading the
single entry in the partition table to find the start position of the partition (a USBZIP drive can thus only contain one partition entry). The BIOS then maps the
USB drive to the Int 13h DL=0 call BUT it will always adds the partition start
address to any access. Thus a BIOS Int 13h DL=0 call to read cylinder 0, head 0
sector 1 (LBA 0) will actually read the first sector of the partition. The real sector
1 (LBA address 0) cannot be accessed at all. For instance, say the USB-ZIP drive
has a partition table with a single entry. The partition table entry indicates that the
partition starts at sector 32, then the BIOS would load sector 32 into memory and
start to execute the code there. Any attempt to read a sector at CHS 0\0\1 (LBA 0)
via a floppy Int 13h DL=0 call (or Extended Int 13h call) from that point onwards,
will actually read sector 32. If the boot code attempts to read CHS 0\1\1 (LBA 32)
it will actually read the sector located at CHS 0\2\1 (LBA 64) as the BIOS will
always add the partition start address on to any access. In this way, the boot code
located at the start of the partition is identical to that found on a floppy disk which
has no MBR or partition table.
Some BIOSes do not support this type of booting and may always boot a USBZIP device as a hard disk (i.e. map the USB device to respond to Int 13h DL=80h
calls) if they see a valid partition table and MBR. The difference between a USBZIP device and a USB-HDD device is very small, both have a master boot record
and a valid partition table, however a USB-ZIP device should contain partition

boot code that expects to be booting from a floppy drive (DL=0) whereas a
USB-HDD device should contain partition boot code that expects to be booting
from a hard disk drive (DL=80h). Many modern BIOSes contain a special menu
option to change this behavior.

About Fake USB Flash memory pen drives

There is a large worldwide problem with fake or counterfeit USB flash memory
drives being sold via web auction sites and markets, etc. These USB drives often
contain faulty memory chips and appear to be larger than they really are. For instance,
a fake USB drive may be sold as being 16GB and the size reported by Windows
may indeed be approx. 16GB, however it may be made with only 2GB of flash
memory and the memory chips themselves may be faulty. As you use it, you may not
see a problem until you fill it with more than 2GB of files. Then you may lose all of
you previous files and the drive may become unformatted and totally corrupt.
If you suspect you have one of these USB drives (or even if you dont!) run the Quick
Test function in RMPrepUSB or use the program H2TESTW.exe (English and
German languages are available in H2TESTW). Here is a quick summary of these two
utilities:

RMPrepUSB QuickTest Very quick but destroys all data on the USB drive.
It is not a thorough test and will not detect the odd bad block or corrupt
memory cell. Recommended for checking if you have a fake undersized
UFD and is very quick.
H2TESTW Non-destructive (fills the USB pen with large files which can be
deleted by you afterwards). Very slow!!!! Tests every byte except for areas
that are filled with the files that are already on it (so best to format it before
testing so it is empty).

There are also other utilities available such as the Russian Check Flash (chkflsh).
Download and run the file English.bat for the English version of this very useful
program.

Frequently Asked Questions

Q1 What happens if I dont tick any of the Override options?
A1 A partition table will be created using a drive geometry of 255 heads and 63
sectors per track. Only one partition table entry will be made. The volume boot record
will be created with hard disk compatible parameters.
Q2 What code is used for the Master Boot Record (MBR) ?
A2 The code used is identical to that used by Vista. It includes BitLocker support so
that if you install Vista or Windows 7 onto a USB hard disk and then enable
BitLocker, it should (!!!) work. The MBR will boot both floppy USB drives and
hard disk USB drives.
Q3 What boot code is used for the Volume Boot Record?
A3 The VBR code will vary depending on what filesystem and format options you
have selected, as follows:

FAT16 + MSDOS MSDOS5.0 identifier, looks for IO.SYS, MSDOS.SYS (or

WINBOOT.SYS). Possible Error Messages: Error!
FAT16 + MSDOS + ZIP MSWIN4.1 identifier, with floppy disk paramters, looks
for IO.SYS, MSDOS.SYS (or WINBOOT.SYS). Possible Error Messages: Invalid
system disk, Disk I/O error, Replace the disk, and then press any key.
FAT16 + FreeDOS FRDOS4.1 which boots KERNEL.SYS (if ZIP option used
then floppy disk parameters are used) Possible Error Messages: Error
FAT16 + BOOTMGR uses MSDOS5.0 identifier and modified boot code and hard
disk parameters. Possible Error Messages: Remove disks or other media, Disk error,
Press any key to restart.
FAT16 + NTLDR uses MSDOS5.0 identifier and modified boot code with hard
disk parameters. Possible Error Messages: NTLDR is missing, Disk error, Press any
key to restart.
FAT32 + MSDOS MSWIN4.1 identifier and boot code which looks for IO.SYS
and MSDOS.SYS (or WINBOOT.SYS). If ZIP option is used then uses floppy disk
parameters. Possible Error Messages: Invalid system disk, Disk I/O error, Replace the
disk and then press any key
FAT32 + FreeDOS FREEDOS which boots KERNEL.SYS. If ZIP option is used
then uses floppy disk parameters. Possible Error Messages: Loading FreeDOS, No
KERNEL.SYS
FAT32 + NTLDR uses MSDOS5.0 identifier and boot code and hard disk
parameters. Includes 4 byte PATCH at E6-E9 changed to 90h (NOP). Possible Error
Messages: Remove disks or other media, Disk error, Press any key to restart.
FAT32 + BOOTMGR MSDOS5.0 identifier. Possible Error Messages:
BOOTMGR is missing, Disk error, Press any key to restart
NTFS + BOOTMGR Vista NTFS boot code. Possible Error Messages: A disk read
error occurred, BOOTMGR is missing, BOOTMGR is compressed, Press
Ctrl+Alt+Del to restart
NTFS + NTLDR XP boot code with 4 byte PATCH at D9-DCh changed to 90h
(NOP). Possible Error Messages: A disk read error occurred, NTLDR is missing,
NTLDR is compressed, Press Ctrl+Alt+Del to restart.
Q4 How do I copy a Vista or Win7 OS install DVD onto a UFD and make it
bootable?
A4 Select the BOOTMGR option + HDD (2PTNs). Browse to the OS DVD and set
the DVD drive letter as the file copy path. Tick the Copy checkbox. Click Prepare
Drive.
See http://www.youtube.com/watch?v=3bh7aeAyTYk for a tutorial.
Q5 How do I copy an XP OS install CD onto a UFD and make it bootable?
A5 There is no simple way to do this and make it bootable. Please visit www.bootland.net for more information. If you wish to install XP onto the hard disk of a PC by
booting from a UFD, you can use WinSetupFromUSB (which has a version of
RMPrepUSB built in).
If instead, you want to boot directly from a UFD try BartPE. Use PE-Builder to
create a BartPE folder (by taking files from an XP installation CD) and then select the
BartPE output folder in RMPrepUSB and tick the COPY FILES box and the PE to
USB box. Also checkout my UBCD4Win tutorial!

Q6 Why does my bootable BartPE\WinPE v2 (Vista) UFD boot on one system

but not on another?
A6 These operating systems expect to be present on a hard disk type of device
which is accessed via Int 13h DL=80h. If a BIOS does not boot successfully, then it is
probably treating the UFD as a USB-FDD or USB-ZIP device and thus mapping the
UFD to Int13h DL=00h and treating the device as a floppy device. It may be possible
to change a setting in the BIOS setup menu (e.g. Emulate USB device as Fixed
Disk) so that the UFD is treated as a hard disk. You should also try setting the HDD
(2PTNs) option and (optionally) also try the ForceLBA option. Also try changing the
filesystem (e.g. use NTFS instead of FAT16). Some BIOSes will treat UFDs below a
certain physical size (not partition size) as a USB-ZIP device, so try a 4GB or larger
UFD. Also, try copying the boot files to the drive before the rest of the files. The best
way to do this is to create a separate folder containing just the boot files (e.g. ntldr,
ntdetect.com, boot.ini for XP, or IO.SYS, MSDOS.SYS and COMMAND.COM for
MS-DOS or KERNEL.SYS for FreeDOS). Try with and without the 2PTNS option as
some BIOSes work well with this option but others will not boot at all!
If you are using MS-DOS or FreeDOS, you can install grub4dos and construct a
menu.lst file that maps (hd0) to (fd0) or vice versa. This allows you to boot to DOS as
A: or C: by mapping one device to another. However this trick does not work for
protected mode operating systems that load their own disk drivers.
IMPORTANT! After re-formatting a UFD, always switch off the target system, insert
the UFD and then switch on the target system. Do NOT just use Ctrl-Alt-Del on the
target system as some systems do not re-detect the type of UFD on a warm reset.
Q7 Why does my MS-DOS bootable UFD boot as drive C: on some systems?
A7 This will be due to the BIOS mapping the UFD as a hard drive (accessible via
Int 13h DL=80h) rather than as a floppy device. Try the Boot as FDD and Boot as ZIP
override options.
Q8 My PC seems to treat UFDs as a floppy device, how can I boot to WinPE
v2?
A8 There are ways to work around this. First try a larger UFD and use the Boot as
HDD option. Please visit www.boot-land.net for other solutions. A typical way is to
use Grub or Grub4DOS as a 2nd stage boot loader which in turn will load the
operating system. For instance, you can boot to a WinPE v2 iso file using Grub4DOS
if your BIOS does not support USB-HDD booting.
Q9 Where can I ask a question about RMPrepUSB or ask for help?
A9 www.boot-land.net (now http://reboot.pro) post specific questions about
RMPrepUSB in the Project Forge USB formatting utilities RMPrepUSB topic, for
other questions choose the most appropriate forum and start a new topic.
Q10 Can I re-distribute RMPrepUSB or use it as part of a commercial
soultion?
A10 You can, but only with the permission of the author or RM Education plc
(UK). This is because although RMPrepUSB and RMPartUSB are Freeware and are
made freely available for private use, it must not be used for commercial purposes or
sold without permission. Any re-distribution must make this clear and contain some
sort of ReadMe file or other notice containing this information as well as this pdf file.
Commercial enquiries should be directed to [email protected], all other enquiries to

the RMPrepUSB topic at www.boot-land.net. RMPrepUSB and RMPartUSB are the

intellectual property of RM Education plc (www.rm.com). RM may ask you to
remove the software or take legal action against you, if these utilities are used for
commercial purposes (i.e. if you are selling it) or you are distributing it without
permission having first been obtained (and after all, its only polite ).
Q11 Does RMPrepUSB/RMPartUSB work under WinPE v2/v3?
A11 Yes as long as MSVBVM60.DLL is present in the same folder! If no USB
drives are listed then copy this file from the WINPE_EXTRA folder to the same
folder that RMPrepUSB.exe is located in.
Most functions will work except perhaps the folder browse button in RMPrepUSB
you may need to type the folder path in manually.
Q12 How can I use RMPrepUSB in my script/batch files?
A12 You cannot, but you can use RMPartUSB. Type RMPartUSB in a Windows
command console window for help. RMPartUSB uses a command line and returns an
errorlevel after completion. You can also use the LIST, GETDRV and FIND
commands
to
find
the
drive
number
of
a
USB
device.
Tip: RMPrepUSB shows the exact command line that it uses to run RMPartUSB. For
instance, you can use RMPartUSB in a cmd script to detect the presence of UFDs,
their drive letters and partition and then format them.
Q13 Sometimes after running RMPartUSB, it returns a large negative error
number why?
A13 This has been observed to occur when using Windows 2000 or when
terminating the RMPartUSB command console window before RMPartUSB has itself
terminated. For instance, if you click the USBInfo button in RMPrepUSB and then
terminate the shell windows that is displayed by RMPartUSB, RMPrepUSB may
report this error message. The reason is unknown.
Q14 I used RMPrepUSB to format my UFD and make it bootable but there are
no files on it and it wont boot?
A14 RMPrepUSB Prepare does not contain or copy any OS boot files unless you
provide them. Microsoft boot files are part of the operating system and cannot be
distributed. You can obtain them if you are licensed to do so from CDs or DVDs or
other sources, or use Freeware like FreeDOS.
Q15 I have set the USB partition size text box to 500 MB, how do I set it back
to the maximum size?
A15 Type MAX in the Size text box or click on the Refresh button or press F5.
Q16 RMPrepUSB reports an error when it runs but I know the UFD is good
why?
A16 Under Vista or Windows 7 you must right-click on RMPrepUSB.exe and
choose Run as Administrator. Later versions contain manifest files so this should
not be necessary and you should be prompted for permission to let RMPrepUSB run
with Administrator privileges. Also, check that Windows has assigned the drive a
drive letter check in the Windows Disk Management console and assign one if
required. You cannot format as NTFS unless Windows assigns the drive a drive letter.

Q17 The Prepare Drive button does not seem to work under Vista nothing
happens?
A17 Try creating a folder at C:\RMPrepUSB do not use a folder in special
locations like the Desktop or My Documents as these may have special limited access
rights under Vista/Win7. Check RMPrepUSB is running with Administrator
privileges.
Q18 I used RMPrepUSB/RMPartUSB and now something is wrong with my
USB pen and I cant seem to access it.
A18 Try the CLEAN and QUICKTEST option. If it tests OK, try to re-format it to a
smaller size (e.g. 512MB). If that looks OK try a larger or maximum size. Use FAT16
or FAT32 (but not NTFS). Partition the USB pen to maximum size and then use
H2TESTW to check the USB drive has no errors. Ensure Windows assigns it a drive
letter. If all else fails, try a different USB format utility.
Q19 What does the QUICK SIZE TEST function do?
A19 Quicktest will check a UFD for duplicate or bad pages. It writes to some
sectors on the UFD and then reads them back to see if the information is correct. For
example, it would write 0 to Sector 0 (first 8 bytes), then 2048 to the first 8 bytes at
the 1Mb point (sector 2048), then 4096 to the first 8 bytes at sector 4096 (2Mb point),
etc. and then reads back the marker values in each of the sectors. This is useful as
a quick test of a UFD. If it passes this test then you should use H2TESTW to run a
thorough test of all bytes. QuickTest is designed to quickly check a UFD to see if it
contains the correct amount of memory chips. If a UFD fails QuickTest then there is
no need to wait hours for it to be tested using H2TESTW or ChkFlsh as you know it
will fail. QuickTest will also report the maximum usable size of memory in the UFD
so you can reformat it to the correct size.
Q20 I ran QUICKTEST and it failed what can I do to fix my UFD?
A20 First you should realize that even if you manage to fix the UFD it will be
very unreliable and may fail (or corrupt the file contents on it) at any time. For
instance, you could copy the latest draft of your new blockbuster novel to it, then
copy it over the top of your master file on your hard disk. Then later you may find out
that you have a corrupted file on your USB drive and have overwritten the original on
your hard drive with the bad version  you have been warned!
One way to fix it is to partition the UFD to a lower volume size. RMPrepUSB or
H2TESTW will usually give you a clue as to what the maximum usable size might be.
When you have decided on a size, proceed as follows (e.g. you have a 4GB pen but
think only 1GB is usable).
1. Use RMPrepUSB to partition and format the UFD use FAT32 or FAT16
rather than NTFS as accessing an NTFS filesystem that has errors or bad
blocks can upset Windows and lead to hangs/crashes. Set the size of the
partition as required. Start low e.g. 800MiB.
2. Run H2TESTW to test the new volume.
3. If the test passes, increase the size in step 1 e.g. 900MiB and repeat steps
1 and 2 until H2TESTW fails.

Q21 I started to use QUICKTEST and H2TESTW and at first I just got a few
errors reported from my 4GiB UFD, but now I get write errors and the system
seems to hang for ages during testing.
A21 This is a typical symptom of cheap or fake UFDs that have been constructed
from faulty memory. The memory may be multiply mapped (e.g. 1GB mapped 4
times so it appears as 4GB) and the controller bad block management probably has
not been set up properly. Error correction may not even be working correctly and the
memory has probably not even been tested thoroughly by the UFD manufacturer.
Everything may appear to be OK as long as you dont use more than 1GB of the UFD,
after that files will begin to get corrupted. In addition, more memory pages may fail
due to the stress of testing (or normal use) over time. If a UFD sector write fails, the
PC can hang/freeze for many minutes on each sector write operation be patient or
pull out the UFD to make it fail quickly.
A UFD from a reliable make and source (Netac, Kingston, Lexar, etc.) can be tested
many times without any problem.
Q22 I have tested my UFD with RMPrepUSB and H2TESTW and it is fine, but
after a week or so I get corrupt files or Windows wants me to reformat it and
thinks it is faulty. If I re-format it then all is well until a few days later is the
UFD faulty?
A22 Are you always using the Windows SystemTray Safely Remove Hardware
icon and ejecting the UFD before pulling it out of the USB port? When Windows
sees a FAT filesystem, it loads the FAT tables into system memory. Any changes
made to the files on the UFD will also cause the FAT tables in Windows memory to
be updated BUT NOT ALWAYS THE FAT TABLES ON THE UFD ITSELF! So
if you simply pull out the UFD, the FAT tables on it will not have been updated. By
using the Safely Remove Hardware feature, you cause Windows to write all the new
FAT table changes to the UFD. This is particularly important if your UFD appears as
a Fixed Disk to Windows and not as a Removable Disk. You can check to see if
caching is used by right-clicking on the UFD drive in Windows Explorer and
choosing Properties Hardware Properties Policies. Even if it is set to Quick
Removal on your PC, you should always use the Safely Remove Hardware icon on
other PCs - so get into the habit and always do it!
If your UFD is formatted with NTFS, again always use the Safely Remove
Hardware icon before pulling out the UFD. The danger is that Windows can write or
read to the UFD at any time, and pulling out the UFD at exactly the same time can
lead to data corruption.
If you are still having problems, try the UFDs which have Ultra Stable Technology
(e.g. Netac) or similar. These UFDs employ a buffering scheme which prevents
corruption due to power loss when a UFD is pulled out during write operations.

Q23 I am having trouble getting some systems to boot. A USB flash memory
pen works on one system but not on another. Some pens work on one system, but
a different pen with an identical image does not work on the same system! What
is going on?
A23 This is a typical problem and it all comes down to the BIOS. Read the
explanation above about how BIOSes boot USB devices. Here are some issues that
have been observed with some BIOSes:

1. The BIOS will not attempt to boot any USB device over 512MB the USB
pen LED will not even flash during system POST as no read request is ever
made!
2. The BIOS will not attempt to boot any USB device over 1GB.
3. The BIOS will treat any USB device under xxx MB as a USB-ZIP device, and
any device over xxx MB as a USB-HDD
4. The BIOS will treat any USB device as a USB-ZIP and always boot it as a
floppy device
5. The BIOS will treat any USB device as a USB-HDD and always boot it as a
hard disk device
6. The BIOS will boot a USB-FDD formatted device that has no MBR or
partition table, but will not boot a USB-ZIP or USB-HDD device
7. The BIOS will boot any device with only a single partition table entry in the
MBR as a floppy device, but will boot a device that has two partition table
entries as a USB-HDD device
8. The BIOS setup menu can be use to make the BIOS always treat a USB device
as a Removable device (USB-ZIP) or a Fixed Disk device (USB-HDD)
depending on user choice.
9. The BIOS looks at the Volume Boot record to determine type of device (e.g. if
it sees MSWIN4.1 then it treats the device as a USB-ZIP device).
10. Partition parameters if the partition has 32hds and 16 sectors per track then
treat it as a USB-ZIP, if 63 sectors then treat it as a hard disk.
11. If the end cylinder is 1023 (max) then treat it as a hard disk.
12. You format the same USB pen using RMPrepUSB and used the same files
(you even make an image and re-used that so you KNOW the USB pen
contents are identical), but it seems to sometimes work and sometimes not on
the same PC it is as if it has good and bad days!
A BIOS may list a USB device in different ways e.g. USB-FDD, USB-KEY,
USB-ZIP, USB-HDD try each option in turn and try different ways of
formatting with RMPrepUSB. Always switch off the test system between each test
NEVER use CTRL-ALT-DEL to warm reboot from a USB drive (some systems
only detect the type of USB drive on a cold boot, so reformatting it and warm
rebooting will not fix the problem unless you cold boot again!).
Be methodical in your testing ALWAYS switch off the system under test before
each test! There are 5 variables to consider FOR EACH TYPE OF PC as below:
1. BIOS MENU settings
2. Physical size of USB device
3. MBR on USB device (there is no MBR on a USB-FDD device or there is
an MBR and partition table on USB-ZIP and USB-HDD devices)
4. Filesystem the volume is formatted with (NTFS, FAT32 or FAT16)
5. Code in VBR (i.e. if the code expects to access a floppy drive or a hard
disk)
The last three (3-5) are determined by settings in RMPrepUSB, the first two must be
changed by the user. I suggest using a 512MB USB pen and a 2GB USB pen for all
testing and make sure they have activity LEDs so you can see if the BIOS is reading
them. Also use FreeDos for all initial testing because FreeDos can usually boot to
either a floppy device or a hard disk device without error (unlike some versions of
MSDOS). Try different BIOS and RMPrepUSB options and write down all results (all

error messages see Q3 above, and if boots as A: or C:).

PC Model and BIOS version (use latest version if possible!)
USB pen make, model, size
RMPrepUSB options used
BIOS settings used
Files added
Result (did the LED flash, any BIOS messages, any boot messages, A: or C:, etc.)
WARNING: In between each test, always switch off the system under test each
time, then switch it on, then go into the BIOS and check the settings and that the USB
pen is listed correctly. If you do not cold boot or reset, the BIOS may remember the
type of USB drive that was fitted previously even though you have just re-partitioned
the USB drive and changed its format and boot type using another computer! Many
computers do not need to be switched off and on again, but some do if your
computer is one that does require to be switched off and on again and you do not do
this, you can spend many frustrating hours trying to work out what is going on!
WARNING: A lot of BIOSes will remove your (previously added) USB drive from
the BIOS drive boot order menu list if you remove the USB pen before you switch it
on again. So always check BIOS boot order every time! Remember, just because one
type of system works with one particular USB pen drive, it does not mean that other
systems will! Have fun and dont pull all your hair out!
Q24 - How can I make a bootable USB pen drive with BartPE on it?
A24 - Simples!
1.
2.
3.
4.
5.
6.
7.
8.

Obtain an XP installation CD
Download PE-Builder (e.g. v3110a)
Copy the contents of the XP CD to say C:\XPCD
Run PE-Builder.exe and select the source folder C:\XPCD
Check the Output folder is set to BartPE and Media Output set to None
Click Build
When finished run RMPrepUSB
Set the options as shown below (use FAT16, FAT32 or NTFS XP, Boot as
USB set.
HDD). Check that setting 5 has both Copy Files and BartPE
9. Click 6 Prepare Drive
10. When finished, click Eject Drive
11. Job done!

See also my website for an UBCD4Win tutorial.

Q25 - I want to copy my own extra files to my BartPE USB drive. Can I do this
automatically?
A25 - Yes. When you tick the BartPE to USB box, after the File Copy, RMPrepUSB
calls the batch file RMPrepUSBXP.cmd. This batch file tweaks the files on the USB
drive to make them bootable and also copies all files in the PEtoUSB folder over to
the USB drive. So simply add your files to the PEtoUSB folder which is located in the
same folder as RMPrepUSB. Alternatively, edit the batch file RMPrepUSBXP.cmd
which is in the same folder as RMPrepUSB, to copy your own folder over. E.g.
xcopy /herky C:\myPEextras\*.* %pen%\*.*
Q26 I want to boot XP/WinPE v1 (not BartPE) the BartPE to USB function
doesnt seem to work with my version?
A26 - You must look on the internet (Boot-Land) to find out how to prepare the
source files correctly and how to convert the files so they will boot from a USB drive.
Once you know how to alter the boot files, you can automate this by using Notepad to
edit the file RMPrepUSBXP.cmd. This file is automatically run when you tick the
BartPE to USB checkbox. If it is just a case of adding extra files to the USB key, you
can simply drop these extra files into the PEtoUSB folder which is located in the same
folder as RMPrepUSB. During the running of RMPrepUSBXP.cmd, any files and
folders that are in the PEtoUSB folder will be copied across (and overwrite) any files
on the USB drive.
Q27 - I want to install BartPE on a USB drive but using Grub4DOS rather than
NTLDR, but I cannot tick the PE to USB checkbox when I select the MS-DOS
option.
A27 - This has been done to prevent mis-use, however there is a deliberate loophole.
First select XP/WinPE and tick the COPY FILES and PE to USB checkboxes. Then
change the radio button option from XP/WinPE to either MS-DOS or FreeDOS. After
RMPrepUSB has run, you can add your DOS boot files and Grub menu files.

Q28 - Will the Speed Test function harm the data on my USB drive?
A28 - The non-destructive Speed Test reads a large amount of data from your USB
drive into memory and then writes back the same data to the USB drive. It should not
corrupt or destroy any of the data on your USB drive HOWEVER... (get out clause
now follows...) if your computer has faulty RAM or the USB flash memory in your
USB drive is unreliable or something else goes wrong, this function may possibly
destroy all the data on your USB drive. For this reason the button has a pink colour to
show that writes to the USB drive will occur and the function could be slightly risky if
using unreliable hardware. Data is written from the start of the drive (in case you
dont have as large a USB drive as you think you have!), so the boot and directory
areas of the drive will be read and written to and thus ***could*** be corrupted (but
it is very unlikely and has not happened to me yet!).
Q29 - How can I test the speed of my USB drives and log the results?
A29 - The Speed Test button performs a read/write speed test and the results are
automatically added to the file USBSpeed.csv in the same folder that you placed
RMPrepUSB.exe in. Just double-click on the .csv file to load it into Excel or a similar
spreadsheet application. There should be two lines for each run (one row for read
speed and one row for write speed). In addition to USBSpeed.csv, a second file
USBSpeedDP.csv is written this file always uses a decimal point for numbers and
commas for separators whereas USBSpeed.csv will use your locale settings (e.g. if
your locale is Holland, it will use ; for separators and , for decimal points and so
Excel will load this correctly as Excel uses locale settings).
USB MODEL

Kingston DataTraveler G2
USB Device

Kingston DataTraveler G2
USB Device

HP v135w USB Device

HP v135w USB Device

Verbatim STORE N GO USB

Device

Verbatim STORE N GO USB

Device

TakeMS MEM-Drive Smart

USB Device

SIZE
(MiB)

Operating System

Platform

Seq. Rd/Wr

SPEED
(MiB/s)

SPEED (MB/s)

3827

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

READ

21.7

23.3

3827

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

WRITE

7.7

8.2

15423

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

READ

31.3

33.6

15423

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

WRITE

11.3

12.2

7639

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

READ

29

31.2

7639

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

WRITE

9.4

10.1

7711

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

READ

33

35.5

TakeMS MEM-Drive Smart

USB Device

7711

Microsoft Windows 7
Professional
(6.1.7600) SP0 64-bit

Intel Corporation (RM plc

AZCB835000CB DQ45CB )

WRITE

6.5

Note that some modern USB drives contain multiple controllers which can greatly
increase the write speed. These types of controllers tend to give better read/write
performance results when using the operating system. For this reason, highperformance USB drives may not give such good results as expected using this test.
For these USB drives, try a benchmark test which uses multiple threads rather than
sequential benchmarking.
Q30 I can boot from a FAT16 2GB UFD formatted as FAT16 but not from a
3GB or bigger UFD why not?
A30 MS-DOS cannot access FAT16 partitions over 2GB (Size=2000MB in
RMPrepUSB/RMPartUSB). Set the partition size to 2000 or use FAT32.
Q31 - What is the difference between using the Syslinux radio button in the Boot
Options section and the Install Syslinux button after formatting?
A31 - Not a lot! The Boot Option radio button will disable NTFS as a choice and use
MSDOS as the OS boot type, then after formatting it will run the syslinux.exe utility
to add the syslinux boot code and replace the DOS boot code. The Install Syslinux
button just lets you run syslinux on any drive at any time without having to format it
first, so if you want to try out a syslinux menu after having made a grub4dos drive,
you can just overwrite the old grub4dos boot code with new syslinux boot code.
Q32 I want to make a language file for RMPrepUSB, how do I do this?
A32 The first step is to convert the English.ini file to your own language using a
text editor that supports UniCode (such as Notepad). Note that the font name, Locale
(LCID) and font sizes are very critical. The file Fonts, CharSets and LCIDs.rtf in
the \LANG folder contains information on which settings to use. Under Windows XP,
to see some Asian languages, it may be necessary to install the Asian Language pack
from the XP CD (using Control Panel Regional and Languages Languages
Install Files for East Asian languages). You should always choose the font and LCID
suggested in the rtf file even if other fonts appear to work, this is because your PC
may be localised for your Region but English versions may not use the correct fonts
for instance for Simplified Chinese use SimSun font even though Tahoma may appear
to work correctly on your computer, it will not work correctly on European PCs.
If you also wish to translate the RMPrepUSB.pdf file, the original Word .doc source
file can be downloaded from the RMPrepUSB website.
Once you have made a new .ini file (and pdf file) simply place them in the .\LANG
folder. Every time you click on the language drop-down box, your new language file
will be re-loaded.
Q33 How do I get the latest version of RMPrepUSB?
A33 Version 2.0.809 and later have a Get Latest Version button on the Help form.
When you click on this button it will attempt to download a version.txt file from the
RMPrepUSB home website. This file contains the version number of the latest fully
released and stable version of RMPrepUSB and will download the ZIP file of the
latest version to the same folder as RMPrepUSB.exe. You will then need to Exit from

RMPrepUSB.exe and unzip the files from the new version and overwrite your current
version (or make a new folder if you prefer). The latest Betas can be found at
http://sites.google.com/site/rmprepusb. Although Betas, they will normally contain
improvements and bugfixes.
Q34 The results from the Speed Test seem very high are they correct?
A34 Yes Chkflsh.exe also gives similar results to RMPrepUSB. The thing to bear
in mind is that the figures shown are for a single 63MiB sequential direct access read
and write. In the real world, this type of access would not be used, so the read/write
figures obtained are usually best case figures for that OS and driver and chipset.
This allows you to compare UFDs without needing to worry about how they are
formatted (FAT16/FAT32/NTFS) or how the operating system is accessing them. In
other words, it is a measure of the USB drive speed and PC hardware but does not test
which filesystem is fastest. So provided you use the same PC and OS, you can
compare different USB drives fairly even if they are formatted differently. It also
means the test is quick! However, note that (for the same UFD) results will vary
depending on the Operating System used, the USB driver used and the mainboard,
BIOS and chipset used to test it with.
Q35 I want to boot to DOS as drive A: when using the Boot as FDD setting, but
my PC always tries to boot it as C: (and I get a command.com not found error),
how can I fix this?
A35 Prepare your UFD for MS-DOS or FreeDOS drive using RMPrepUSB and the
Boot as HDD setting, then use the install grub4dos button to install grub4dos.
Then create a menu.lst file as below (the lines beginning with # are comments and can
be omitted):
title MS-DOS (AS FLOPPY) AND HDD as HDD0
map (hd0,0)+1 (fd0)
# map the first partition of the hard disk as a floppy disk
map (hd0) (hd32)
# map the UFD as a virtual cd
map (hd1) (hd0)
# map the real hard disk as hard disk 0
map --hook
# hook Int13 interrupts so all map changes take affect
chainloader (fd0)/io.sys
# load the io.sys code into memory from the floppy disk (now ufd is fd0)
rootnoverify (fd0)
# set the file root as the floppy disk
map --floppies=1
map --harddrives=1
# Tweak BIOS device numbers so DOS sees 1 floppy and 1 hd
(if using FreeDOS replace io.sys with kernel.sys in the above menu). The above
menu re-maps the UFD partition which appears as a hard disk in the BIOS after
booting, to appear as a floppy disk drive.

Q36 When I boot from a USB device and run ImageX (or another imaging
utility) to capture an image, it does not work and refuses to save the image
why?
A36 You cannot save files larger than 4GB on a FAT32 volume. Try formatting the
USB device with the NTFS filesystem.
Q37 How can I make an image of my Windows hard disk and copy it to
another hard disk on another system (or lots of systems)?
A37 I would recommend booting to WinPE (VistaPE or Win7PE) from a USB flash
drive (of course!) and then using the Microsoft tool ImageX.exe after using
sysprep.exe. For a getting started guide, see my tutorial on the RMPrepUSB site here.
Q38 Where has H2TESTW gone?
Q38 The author has requested that I dont include a copy in my download and that
you download the latest version from his website. Use the Help button on
RMPrepUSB and then click on the H2TESTW link.
Q39 When using grub4dos and loading an ISO file I get a Error 60: File for
drive emulation must be in one contiguous disk area error but it used to work
before?
A39 - Typically, you will get the non-contiguous error when you have edited or
deleted files on the USB drive and then copied over an iso file or simply overwritten
the old iso file with the new iso file. If you get this error when trying to boot an ISO
file using grub4dos from a USB Flash Drive, you can run WinContig to fix the ISO
file, but it is very slow when run on a USB flash drive. A much quicker way to fix the
problem is to copy all the files over to your hard disk, run RMPrepUSB again on the
UFD to reformat it and then run grub4dos and then copy all the files back again. If
this is not possible, then always copy the iso file to the USB drive first, before you
edit any files on the USB drive.
Q40 My USB drive is not listed by RMPrepUSB why not?
A40 RMPrepUSB should list all USB drives that are over 0 bytes in capacity. U3
USB flash drives may not be listed unless they have been enabled by the U3 Launcher
application. If you are running BartPE or Windows PE or WINE under linux with
WINE, it is possible that you need the MSVBVM60.DLL (which is normally present
in Windows XP and later Windows versions). Copy the file from the
\WINPE_EXTRA folder in the full download to the same folder that
RMPrepUSB.exe is located in. This file is also required for RMPartUSB.exe.
Q41 When booting grub4dos on some PCs I just get a flashing cursor (or
missing mbr Helper message) and no grub4dos menu, but other PCs boot fine
why?
A41 This is caused by the BIOS code, but can often be fixed by installing grub4dos
to the Partition Boot Record (PBR or sometimes called VBR) instead of the Master
Boot Record (MBR). When you click on the RMPrepUSB Install grub4dos button,
choose the PBR option. Also try changing the Boot to HDD option (some BIOSes
dont like this option, some only boot with it!). This issue should be fixed in v2.1.607
and later and you should be able to install grub4dos to either PBR or MBR.

Q42 When I load the USBSpeed.csv file in OpenOffice (or Excel), I do not get
the proper columns why?
A42 This is because Excel takes account of your regional settings (locale) but
OpenOffice does not. If USBSpeed.csv does not load properly, try USBSpeedDP.csv
which always contains decimal points for numbers and commas for field separators.
In versions before 2.1.503, the format of the CSV file was that each field was
separated by a comma, but the number format would be written in your own locales
format. This meant that for non-US/UK countries (e.g. Germany), you could get a
CSV file such as:
aaa,bbb,ccc,ddd,5,6,6,2
instead of
aaa,bbb,ccc,ddd,5.6,6.2
To further complicate the problem, the correct CSV format expected by Excel in nonUS/UK countries is to use a semi-colon as a separator and a comma as a decimal
point. E.g.
aaa;bbb;ccc;ddd;5,6;6,2
Version 2.1.503 and later of RMPartUSB, now writes two CSV files:
USBSpeed.csv which writes according to the locale on your computer (e.g. in
Germany it writes aaa;bbb;ccc;ddd;5,6;6,2) and USBSpeedDP.csv which always
writes a CSV file with commas as separators and dots as decimal points
(aaa,bbb,ccc,ddd,5.6,6.2). So use USBSpeed.csv if using Excel, or USBSpeedDP.csv
if you application always expects commas and decimal points.

Q43 - How can I copy an image onto a USB drive of a different size?
A43 - You cannot re-size an image using RMPrepUSB. So you need to follow these
steps:
1. Determine the minimum partition size required to hold all the files in the
image (e.g. say it is 2.7GiB)
2. Set the size in RMPrepUSB to just larger (say 2.9GiB) and reformat the
USB drive to that size
3. Prepare and test the USB drive to make sure it works on all systems
4. Make a USB-->File image using the PALL setting
5. Now use the File-->USB button to copy the image to all your other USB
drives (which must be at least 2.9GiB in size)
6. If you want to expand the partition and it is a single NTFS partition (do not
use HDD 2PTNS option), then use Windows Diskpart command as follows:
DISKPART
LIST VOL
SEL VOL J: (assuming J: is the volume letter given to your USB drive that
you want to expand)
EXTEND
If you have a single FAT16 or FAT32 partition or want to use a GUI, try the free
program EASEus Partition Master for 32-bit Windows which can be download here.
Q44 - I am booting to BartPE/UBCD4Win and get the XP error PreLogon File
not found. This does not happen when booting from CD. How do I fix this?

A44 - You probably prepared the OS files on a Vista or Win 7 system. Create a folder
on your USB drive under \MININT called \Registration. Copy the file from your
Windows Vista/7 hard disk folder C:\Windows\Registration\R000000000001.clb to
make the file \MININT\Registration\R000000000001.clb on your USB drive.
Q45 - I get a BSOD when booting BartPe from USB - why?
A45 - Try replacing the ntdetect.com file with the one from W2K3 SP2. Some Dell
systems for instance, require this.
Q46 - My (Dell) system does not boot to grub4dos menu after using HDD+Force
LBA options why?
A46 - Some BIOSes do not 'like' the Force LBA option - only try this option if the
USB pen will not boot without it.
Q47 - My USB device does not appear in the drive list why?
A47 - To appear in the device list, the USB drive must appear as a \\physicaldrivex
device in Device Manager, must have a size of greater than 0 bytes and must be
classed as a USB device. RMPrepUSB v2.1.2 and later have improved USB detection.
Note that password protected U3 devices will not appear in the menu unless you have
enabled the USB storage device using the U3 Launcher software.
Q48 - My USB Flash drive seems to be faulty, it takes a LONGGGGGGG time to
access it even under RMPrepUSB and my system just stops responding. Should I
throw it away?
A48 - No! It probably has corrupt data on it and Windows cannot understand it, the
USB drive itself is probably fine. You need to wipe the data from the drive but as
Windows cannot access the drive, you have to find another way to clean it see here
for details.
Q49 - What is a GiB or MiB or KiB?
A49 - Drive manufacturers use KB to mean 1 thousand bytes (i.e. 1000), but
computers (operating systems and applications) often regard 1024 bytes as being
equal to '1KB'. To avoid this confusion the new abbreviation KiB was invented. So
1KiB=1024
bytes,
1MiB=1024x1024
bytes
or
1048576
bytes,
1GiB=1024x1024x1024 bytes or 1073741824 bytes. This means that a 160GB hard
drive may actually appear as 149GiB in Windows (which it still calls 'GB' not GiB)
which is the same as 160GB. RMPrepUSB uses GiB, so a 32GB USB flash drive may
appear as 29.8GiB in RMPrepUSB or 29.8GB Windows. Still confused you would
think a computer could display a size correctly wouldnt you?
Q50 - How do I use RMPrepUSB on a (non-USB) SATA or IDE hard drive?
A50 Use the Alt+F5 key combination. Alternatively, you can open a command
prompt (shell) window as an Administrator (right-click and Run as Administrator on
Start Menu - Program Files - Accessories - Command Prompt) and then type
RMPREPUSB ALLDRIVES. You should then have access to all physical storage
drives except floppy drives and CD/DVDs. Take care not to format or install
grub4dos to the wrong drive!
Q51 - I used the syslinux option but I cannot get the syslinux.cfg menu to display
- I just get a black screen instead and it seems to hang?

A51 - This is probably due to the version of syslinux.exe not matching the version of
vesamenu.c32 in your OS files on the USB drive.
When you use the Syslinux options in RMPrepUSB, it uses the syslinux.exe version
that is in the same folder as RMPrepUSB.exe. Currently this is a version 4.0x.
Edit the syslinux.cfg menu file to use menu.c32. If that works then it is a
vesamenu.c32
issue
(probably
wrong
version
of
vesamenu.c32).
Either find another version of the vesamenu.c32 file or try replacing the syslinux.exe
file in the RMPrepUSB menu with different version of syslinux.exe and re-running
RMPrepUSB so that syslinux is re-applied to the USB drive. COM32R versions of
vesamenu.32 that are dated 2010 will probably require syslinux v4.03 or later.
Syslinux v4+ needs a vesamenu.c32 file in COM32R format. The version of syslinux
included with RMPrepUSB versions before 2.1.604 used an older version which
requires COM32 format files (v3). RMPrepUSB version 2.1.604 and later use
syslinux 4.03 (or later) which requires COM32R .c32 files.
Different versions of syslinux.exe and their .c32 files are included with later versions
of RMPrepUSB in the syslinux sub-folder. If you have version incompatibility
problems, use the v4 .c32 files in your USBs syslinux.cfg menu.
If you are unsure which version of syslinux to use, check the vesamenu.c32 and
menu.c32 files in your linux ISO and compare them against the ones in the
RMPrepUSB syslinux folders then copy the correct version of syslinux.exe from the
subfolder to the same folder that contains RMPrepUSB.exe.
Q52 When I run Quick Size Test capacity test, sometimes it reports an error
(e.g. last sector bad) and sometimes it does not. Also, sometimes RMPartUSB
seems to pause for 2 minutes before completing how can I fix this?
A52 First try disabling your antivirus software. In particular if you have a USB
drive which has been formatted as FDD or USB-FDD, then the antivirus software
may start scanning it which will interfere with the actions of RMPartUSB. Secondly,
reboot Windows to try to clear the error.
Q53 I am having problems running QEMU F11 function (v2.1.618 and later)?
A53 To emulate booting from the USB drive selected in the RMPrepUSB dropdown
selection box, just press F11. When choosing the amount of virtual RAM memory to
use, RMPrepUSB suggest a memory size of approx. 50% of Windows available
memory. If QEMU does not seem to launch, try reducing the virtual memory size
until it will run.
Check you have the two files StartFromUSB.cmd and CreateImg.cmd. These are the
two files that are called by RMPrepUSB to run QEMU. If the two .cmd files do not
appear to work, you can debug them by editing them in notepad and placing the word
pause at the end of the file. As the command shell is minimized by Windows during
running, you will need to find the minimized command shell task and maximise it to
see what error messages you get and then press Enter to continue.
The F11 feature allows you to create an empty virtual hard disk or use the existing
one on your computers hard drive as a file. It is always named harddisk.img and
will be located in the QEMU folder below the RMPrepUSB application folder. If you
want to use your own hard disk image then replace it with your own file. By using a
virtual hard disk, you can test OS install USB drives (e.g. install XP or DOS onto the
virtual hard disk). If you include a grub4dos menu.lst entry to boot from the hard
drive, you can then boot from the virtual hard disk that you have just installed the OS

onto. For instance you can create a USB drive which will install XP onto a hard drive
and then boot to XP from the virtual hard drive.
Results with QEMU however are variable it may or may not work! It also runs a lot
slower than a real system. It will not harm the PC that you run it on however and so it
is quite safe to try it.
Q54 Can I copy a bootable virtual disk to a drive using the File->USB feature?
A54 Yes, in version 2.1.625 and later, .vdi, .vmdk, .qcow, .qcow2, .cloop,.vhd,
.dmg, .vpc, .vvfat and .nbd files are supported. These files are first converted to a
raw format using the qemu-ime.exe utility. If conversion is successful, then
RMPrepUSB will use the raw file as the source file. The raw file is created in the
RMPrepUSB\QEMU folder and may be quite large. You will be asked if you want to
delete it after it has been used.
If the conversion fails, you can look in the QEMU folder for the file info.txt to see
what the problem was.
--- o O o ---