Peak Discharge

Runoff
Runoff starts when the rainfall rate exceeds the rate of infiltration. For lumped models rainfall
volume can be obtained by integrating the rainfall excess:
t
t
Q (i f )t
Where Q is the runoff volume, i is the rainfall rate, and f is the infiltration rate. Various methods
have been developed to determine flow volumes, peak flow rates, and runoff hydrographs.
These methods work reasonably well for hydrologic models, but are less effective for water
quality models, since sediment or chemical concentrations are dependent on flow path.
Estimating Runoff Volume

SCS (NRCS) Curve Number Method
In this method, the total rainfall is separated into three components as shown below,
i
Q
Ia
P-Q
t
Ia is the initial abstraction before ponding (in),

P is the cumulative rainfall (in)
Q is the runoff (in)
Q is estimated from the following relationships:
( P - I a )2
Q=
(P - I a + S)
Where S = maximum soil water storage potential (in) and is given by
1000
S
10
CN
Values of CN, the Curve Number, have been established for various situations.
Average coefficients are calculated for composite areas:
CN
CN i Ai
Ai
where Ci is the coefficient applicable to the area Ai.
Curve Numbers from TR-55 (Urban Hydrology)

Land Use
Description on
Input Screen
Curve Number
for Hydrologic
Soil Group
Cover Description
Cover Type and Hydrologic Condition
%
Impervious A
Areas
Agricultural
Row Crops - Staight Rows + Crop Residue CoverGood Condition (1)
Commercial
Urban Districts: Commerical and Business
Forest
Woods(2) - Good Condition
30 55 70 77
Grass/Pasture
Pasture, Grassland, or Range(3) - Good

Condition
39 61 74 80
High Density
Residential
Residential districts by average lot size: 1/8 acre

or less
65
77 85 90 92
Industrial
Urban district: Industrial
72
81 88 91 93
Low Density
Residential

lot
25
54 70 80 85
Open Spaces
Open Space (lawns, parks, golf courses,

cemeteries, etc.)(4) Fair Condition (grass cover
50% to 70%)
Parking and
Paved Spaces
Impervious areas: Paved parking lots, roofs,

drivesways, etc. (excluding right-of-way)
100
98 98 98 98
Residential 1/8
acre

or less
65
77 85 90 92
Residential 1/4
acre
38
61 75 83 87
Residential 1/3
acre
30
57 72 81 86
Residential 1/2
acre
25
54 70 80 85
Residential 1 acre Residential districts by average lot size: 1 acre
20
51 68 79 84
Residential 2
acres
12
46 65 77 82
Water/ Wetlands
Residential districts by average lot size: 2 acre
64 75 82 85
85
89 92 94 95
49 69 79 84
Runoff curve numbers for hydrologic soil cover
Hydrologic Soil
Group
Land Use
Treatment or
Practice
Hydrologic
Condition
Fallow
Straight Row
---
77
86
91
94
Straight Row
Poor
72
81
88
91
Good
67
78
85
89
Poor
70
79
84
88
Good
65
75
82
86
Poor
66
74
80
82
Good
62
71
78
81
Poor
65
76
84
88
Good
63
75
83
87
Poor
63
74
82
85
Good
61
73
81
84
Poor
61
72
79
82
Good
59
70
78
81
Poor
66
77
85
89
Good
58
72
81
85
Poor
64
75
83
85
Good
55
69
78
83
Poor
63
73
80
83
Good
51
67
76
80
Poor
68
79
86
89
Fair
49
69
79
84
Good
39
61
74
80
Poor
47
67
81
88
Fair
25
59
75
83
Good
35
70
79
Natural
Good
30
58
71
78
Natural
Poor
45
66
77
83
Fair
36
60
73
79
Good
25
55
70
77
---
---
59
74
82
86
(dirt)
---
72
82
87
89
(hard surface)
---
74
84
90
92
Row Crops
Contoured
Terraced
Straight Row
Small Grain
Contoured
Terraced
Straight Row
Close-seeded Legumes or Rotation

Meadow
Contoured
Terraced
Natural
Pasture or Range
Meadow
Contoured
Woods
Farmsteads
Roads
Definition of SCS Hydrologic Soil Groups:

3.4 Definition of SCS Hydrologic Soil Groups:
The SCS has classified more than 4000 soils into four hydrologic soil groups (HSG) according
to their minimum infiltration rate obtained for bare soil after prolonged wetting.
Soil Group
Description
Final Infiltration
Rate (mm/h)
Soil
Texture
Lowest runoff potential. Includes deep

sands with very little silt and clay, also
deep, rapidly permeable loess.
8-12
sand,
loamy sand,
sandy loam
Moderately low runoff potential. Mostly

sandy soils less deep than A, and loess less
deep or less aggregated than A, but the group
as a whole has above-average infiltration
after thorough wetting
4-8
silt loam,
loam
Moderately high runoff potential. Comprises

shallow soils and soils containing considerable
clay and colloids, though less than those of group
D. The group has below-average infiltration after
presaturation.
1-4
sandy clay
loam
Highest runoff potential. Includes mostly clays of 0-1

high swelling percent, but the group also includes
some shallow soils with nearly impermeable
subhorizons near the surface.
clay loam,
silty clay
loam,
sandy clay,
silty clay,
clay
Rainfall (inches)
Direct Runoff (inches)
Estimating Peak Discharge

When water entering an area is more than what can be transmitted or routed by established
watercourses, flooding occurs. Generating hydrographs from big storms becomes the job of
flood prediction. We use the word prediction because we still deal with probabilities of events.
Some of the reasons we study runoff peaks and volumes are:
To quantify the volume and rate of water to be handled by water management facilities
To predict soil erosion and transport of surface pollutants
To identify critical non-point source pollution areas
Peak Discharge The maximum volume flow rate passing a particular location during a storm
event. Peak discharge has units of volume/time (e.g. ft3/sec, m3/sec, acre-feet/hour).
The peak discharge is a primary design variable for the design of stormwater runoff facilities
such as pipe systems, storm inlets and culverts, and small open channels. It is also used for some
hydrologic planning such as small detention facilities in urban areas.
There have been many different approaches for determining the peak runoff from an area. As a
result many different models (equations) for peak discharge estimation have been developed.
Ideally, we would like to have a 30-year flood record available at every site where a peak
discharge estimate is needed for design work. If such data were always available, then a
frequency analysis of the flood record could be used to characterize the flood potential at the site
of the design work.
More often than not, flood records are rarely available where peak discharge estimates are
needed for design work. Therefore, it is necessary to use either a prediction method that was
developed from flood frequency analyses of gaged data in the region or an uncalibrated
prediction equation that was designed for use at ungaged sites.
.
Rational Method
The most widely used uncalibrated equation is the Rational Method. Mathematically, the
rational method relates the peak discharge (q, m3/sec) to the drainage area (A, ha), the rainfall
intensity (i, mm/hr), and the runoff coefficient (C).
q = 0.0028CiA
SI Units
Where q = design peak runoff rate in m3/s

C = the runoff coefficient
i = rainfall intensity in mm/h for the design return period and for a
duration equal to the time of concentration of the watershed.
q = CiA
English Units
Where q ft3/sec
i = rainfall intensity (in/hr)
A = watershed area in acres
C = runoff coefficient, ratio of the peak runoff rate to the
rainfall intensity, dimensionless
To use the rational method there are a few assumptions.
Rainfall intensity and duration is uniform over the area of study

Storm duration must be equal to or greater than the time of concentration of the
watershed.
Time of Concentration (Tc)

Definition The time required for water to flow from the most remote (in time of flow) point of
the area to the outlet once the soil has become saturated and minor depressions filled. It is
assumed that when the duration of the storm equals the time of concentration, all parts of the
watershed are contributing simultaneously to the discharge at the outlet. There are several
methods for computing time of concentration. Two of the most popular methods are the Kirpich
equation and the SCS lag formula.
Kirpich Formula
Tc = 0.0078 L0.77S-0.385
where Tc = time of concentration in minutes.
L = maximum length of flow (ft)

S = the watershed gradient (ft/ft )or the difference in elevation between the
outlet and the most remote point divided by the length L.
SCS Lag Formula
Tc = 0.00526 L0.8(1000/CN 9)0.7 S-0.5

where L = watershed length (ft)
S = watershed slope (ft/ft)
CN = curve number
Rational Method Runoff Coefficients

The rational method uses runoff coefficients in the same fashion as the SCS curve number
method for estimating runoff volume. Below are several tables for different land conditions.
Runoff Coefficient C for Agricultural Watersheds [Soil Group B] (Schwab et al., 1993).
Crop and Hydrologic
Condition
Row crop, poor practice
Row crop, good practice
Small grain, poor practice
Small grain, good practice
Meadow, rotation, good
Pasture, permanent, good
Woodland, mature, good
Coefficient C for Rainfall Rates of

25 mm/h
100 mm/h
0.63
0.47
0.38
0.18
0.29
0.02
0.02
0.65
0.56
0.38
0.21
0.36
0.17
0.10
200 mm/h
0.66
0.62
0.38
0.22
0.39
0.23
0.15
C Factor Conversion Factors for Hydrologic Soil Groups A, C, and D.

Crop and Hydrologic
Condition
Row crop, poor practice
Row crop, good practice
Small grain, poor practice
Small grain, good practice
Meadow, rotation, good
Pasture, permanent, good
Woodland, mature, good
Factors for Converting C from Group B Soils to

Group A
Group C
0.89
0.86
0.86
0.84
0.81
0.64
0.45
1.09
1.09
1.11
1.11
1.13
1.21
1.27
Group D
1.12
1.14
1.16
1.16
1.18
1.31
1.40
Average coefficients are calculated for composite areas:
Ci Ai
Ai
where Ci is the coefficient applicable to the area Ai.
SCS Triangular Hydrograph Method

In this method, peak runoff is determined using the curve number approach. The assumption of
uniform rainfall still applies. The hydrograph takes on a triangular shape with equal peak and
flow volume as in the rational method. This can be seen below.
Peak runoff rate is calculated by
q = 0.0021QA/Tp
where Q = runoff volume in mm depth (from the curve number)
q = runoff rate in m3/s

A = watershed area in ha.
Tp = time of peak in hours
In this method, the time to peak does not equal the time of concentration as in the rational
method, in this method time to peak Tp equals
Tp = D/2 + TL = D/2 + 0.6Tc

Where Tp = time to peak (hours)
D = duration of excess rainfall
TL = time of lag
Tc = time of concentration
It is assumed that the total time of flow is 2.67 Tp and the recession time of the hydrograph is
1.67 Tp.
Time of concentration is calculated using the SCS Lag formula discussed earlier

Peak Discharge

Uploaded by

Copyright:

Available Formats

Peak Discharge

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Peak Discharge

Uploaded by

Copyright:

Available Formats

Runoff

Estimating Runoff Volume

Ia is the initial abstraction before ponding (in),

where Ci is the coefficient applicable to the area Ai.

Curve Numbers from TR-55 (Urban Hydrology)

Cover Type and Hydrologic Condition

Row Crops - Staight Rows + Crop Residue CoverGood Condition (1)

Urban Districts: Commerical and Business

Woods(2) - Good Condition

Pasture, Grassland, or Range(3) - Good

Residential districts by average lot size: 1/8 acre

Urban district: Industrial

Residential districts by average lot size: 1/2 acre

Open Space (lawns, parks, golf courses,

Impervious areas: Paved parking lots, roofs,

Residential districts by average lot size: 1/8 acre

Residential districts by average lot size: 1/4 acre

Residential districts by average lot size: 1/3 acre

Residential districts by average lot size: 1/2 acre

Residential 1 acre Residential districts by average lot size: 1 acre

Residential districts by average lot size: 2 acre

Runoff curve numbers for hydrologic soil cover

Close-seeded Legumes or Rotation

Definition of SCS Hydrologic Soil Groups:

Lowest runoff potential. Includes deep

Moderately low runoff potential. Mostly

Moderately high runoff potential. Comprises

Highest runoff potential. Includes mostly clays of 0-1

Direct Runoff (inches)

Estimating Peak Discharge

Where q = design peak runoff rate in m3/s

Rainfall intensity and duration is uniform over the area of study

Time of Concentration (Tc)

L = maximum length of flow (ft)

SCS Lag Formula

Tc = 0.00526 L0.8(1000/CN 9)0.7 S-0.5

Rational Method Runoff Coefficients

Coefficient C for Rainfall Rates of

C Factor Conversion Factors for Hydrologic Soil Groups A, C, and D.

Factors for Converting C from Group B Soils to

Average coefficients are calculated for composite areas:

where Ci is the coefficient applicable to the area Ai.

SCS Triangular Hydrograph Method

Peak runoff rate is calculated by

q = runoff rate in m3/s

Tp = D/2 + TL = D/2 + 0.6Tc

You might also like