Kawa Ninja 650-Charging System
Kawa Ninja 650-Charging System
Kawa Ninja 650-Charging System
By: Kiwi
A number of owners have reported that their Regulator/Rectifier (R/R) have
failed, often this was preceded by a headlight failure and a flat battery leading to
starting issues. Troubleshooting found that not only had the R/R failed but in
some cases the R/R electrical connector had melted with some pins showing signs
of corrosion. The headlight issue was later traced to the headlight relay.
Troubleshooting Index
1. System Overview
2. Components and Locations
3. Circuit Diagram
4. Common Problems and Remedies
5. Battery Checks
6. Rotor/Stator Checks
7. Regulator/Rectifier Checks
8. Regulator/Rectifier Connector
9. Headlight Relay
Tools Required
Digital Multimeter and test leads with a male & female spade fittings
Tools required for access (spanners, allen keys, sockets and screwdrivers)
Charging System Overview
In simplified terms the Ninja 650R (ER-6F) and ER-6N uses a stationary Stator
Coil mounted to the left hand crankcase cover, it sits inside the flywheel Rotor.
The Rotor has magnets so that when the engine is running these rotate around
the Stator producing alternating current (AC). The Stator is wired in such a way
that there are actually 3 circuits which produce a 3 phase AC output voltage.
This Alternator (Rotor/Stator) setup is connected to a Regulator/Rectifier (R/R) by
3 wires. The R/R rectifies the AC current by using 6 diodes (2 per phase) and
converting it to a useable direct current (DC). The more complex part of the R/R
is the regulator section, it regulates the higher DC current down to provide a
steady 12-14 volts DC. The process in simplest terms monitors the output
voltage and "shunts" (partially diverts) the excess portion to ground through a
load.
The R/R has a lot of current constantly flowing through it and the excess voltage
is being diverted to ground through the load so the R/R gets very hot in the
process. The construction of the R/R is all about dissipating this heat through the
heat fins on its exterior.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Components and Locations
Stator removed
Stator mounted in left hand crankcase cover
Rotor left hand crankcase cover removed
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Regulator/Rectifier below seat left hand side
Relay Box under fuel tank
Relay Box
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Battery underseat (black terminal ve) (red terminal +ve)
Circuit Diagrams
1. Ignition Switch
2. Alternator
3. Rectifier / Regulator
4. Water-proof Joint
5. Main Fuse 30 A
6. Battery 12 V 10 Ah
7. Load
Wiring Colour Code
BK Black BR Brown GY Gray
BL Blue G Green LB Light Blue
LG Light Green O Orange P Pink
PU Purple R Red W White
Y Yellow
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Worth noting is that all the wiring diagrams available for all models of the Ninja
650R, ER-6F and ER-6N refer to the three AC wires coming out of the Stator to
the R/R as black when in fact they are white.
Common Problems and Remedies
Failure of the Regulator/Rectifier (R/R) is often first evidenced by a flat battery
and starting issues. Troubleshooting should always start with the battery.
Make sure you have a good battery. A bad, old or dead battery will load down
the charging circuit until it overheats and dies. You know when you put a dead
battery on charge and it pegs the battery charger ammeter? Well that is what a
bad battery is doing to charging components on your bike.
Having said that. Numerous posts on internet forums with this fault have
indicated that more often than not a failed R/R is the culprit. This is often found
in association with corroded or damaged pins on R/R electrical connector or loom
plug pins. It may be that these are just the weakest link in the chain.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Damaged Regulator/Rectifier Loom Plug
Damaged Regulator/Rectifier connector pins
Those who have experienced headlight issues also find that the headlight relay is
at fault. The headlight relay is part of the Relay Box and also contains 3 diodes.
Posts to date do not indicate whether it is the diodes or the actual headlight relay
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
at fault. Unfortunately the individual relays and diodes cannot be replaced and
the relay box is sold as a complete unit.
The Service Manual has a complete series of tests for both the headlight relay and
diodes, as the Relay Box is not a cheap item it would be advisable to confirm
serviceability before making an expensive purchase.
The Battery
The following is taken from the Ninja 650R (ER-6F) & ER-6N Battery FAQ.
Is it the battery, or the charging system, or something in-between? The best way
to know for sure is to use a Multimeter selected to DC Volts (20 volt range)
attached directly to the battery positive and negative terminals, and observe the
following:
1. With the engine and all electrical accessories switched off, the battery should
read a minimum of 12.7 volts DC. If not, the battery is either not fully charged,
or it is bad (it is incapable of holding a full charge).
Charge the battery fully with a battery charger and check again. Remember
however that you must wait at least one hour after charging the battery to
conduct this test. Then if the reading is less than 12.7 volts DC, the battery is
bad and should be replaced.
State of Charge Digital Voltmeter
100% 12.7 volts DC
75% 12.4 volts DC
50% 12.1 volts DC
25% 11.9 volts DC
0% 11.8 volts DC
2. If the first test above passes, leave the Multimeter hooked up to the battery
terminals, and press the starter button. While the starter is engaged (but before
the bike starts) the battery voltage should be 9.5 volts DC or greater. If not,
then this signals either a bad battery, very dirty or weak electrical connections, or
it could be a problematic starter motor (not likely it's probably the battery).
3. The charging system output voltage should be checked, again with the
multimeter at the battery terminals and this time with the engine is running.
Start the engine and operate at various RPM with the headlight on and off (to
turn off the headlight, disconnect the headlight connector).
The readings may show nearly battery voltage when the engine speed is low,
and, as the engine speed rises, the readings should also rise. But they must be
kept under the specified voltage.
According to the Kawasaki Service Manual the measured voltage should be 14.2 -
15.2 volts DC at about 2000-3000 rpm. In reality it is more likely to be in the
range of 13.5 15.0 volts DC.
NOTE: If the alternator is outputting more than 15.2 volts DC to the battery, the
Regulator/Rectifier (R/R) unit is bad and should be replaced. Over-charging a
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
battery will quickly ruin it and may cause severe damage or failure of other
electrical components such as the ECU.
If the charging voltages are too low and do not rise as engine speed increases,
suspect the alternator or R/R.
If the charging voltages are too high, suspect the R/R unit firstly, then perhaps
dirty or corroded electrical terminals. The procedure for checking all of these is
too detailed to describe here so consult the Service Manual for additional details.
4. Although is not related to charging system, another issue such as wiring or an
accessory may be causing battery discharge. To check this carry out a current
leakage check as follows:
Ensure the battery is fully charged and check that the battery voltage measures
above 12.7 volts DC (test 1 above). Disconnect the negative (black ve) lead
from the battery terminal (stud). Measure the Leakage Current of the bike by
setting the multimeter to DC Amps, connect one multimeter probe to the battery
negative terminal and connect the other multimeter probe to the negative lead.
The current should be no higher than about 5.0 mA (milliamps) with the ignition
switched OFF. In reality you should expect to see around 1.0 to 2.0 mA.
If Current Leakage exceeds 5.0 mA, there is a fault with wiring harness an
accessory such as an alarm or the R/R draining the battery. Try pulling fuses or
disconnect the R/R to locate the problem.
The Rotor/Stator
To check the integrity of the stator there are a number of tests that can be
carried out. The integrity of the Rotor is more difficult to test and in reality can
only be confirmed serviceable by swapping with a known good part. As the only
thing likely to go wrong with a Rotor is a loss of magnetism (and that is very
unlikely) then this should only be considered when there is no alternator output
voltage and all the other tests have checked out OK.
1. To carry out a resistance check of the Stator windings use a Multimeter
selected to Ohms ( range). Connect the multimeter leads and measure the
resistance between each pair of windings. Black wire to black wire pins, 1-2, 2-
3 & 1-3.
There are two points where this can be done easily, the connector at the
Regulator/Rectifier R/R) or you can follow the 3 wires out of the left hand
crankcase cover up to an Alternator Lead connector.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Alternator Lead connector
The resistance between each pair of wires should be in the 0.18 - 0.27 ohms
range.
A very low winding resistance could be a shorted winding although that is not that
common, what normally happens is they burn through and go open circuit with
infinite resistance (multimeter displays dashed lines or the abbreviation "OL"
which stands for "open loop"). In either case the Stator will require replacement.
A cooked Stator is usually obviously when removed with a burnt look to the
windings and insulation.
2. The next test is a check of the stator windings to ensure that there is not a
short circuit to earth (the engine casing). For this test again use the multimeter
selected to Ohms ( range), connect one of the multimeter leads to the engine
casing and the other lead to each of the black wires pins 1, 2 & 3 separately.
There should be an open circuit with infinite resistance (multimeter displays
dashed lines or the abbreviation "OL" which stands for "open loop").
If the multimeter displays a low resistance then it is likely that the windings
insulation has burnt through and is shorting to earth through the Stator
mountings. In this case the Stator will require replacement.
3. The final check is the Alternator output. Again either unplug the connector to
the R/R or the Alternator Lead connector from the Stator windings LHS. Run the
engine and with the multimeter selected to AC Volts (250 volt range) measure
the AC voltage across each 3 pairs of Stator wires. Black wire to black wire pins,
1-2, 2-3 & 1-3.
Caution All the Alternator wires are live, use test leads with appropriate male or
female spade connectors to avoid an electrical short circuit and damage.
The output voltage should be about 42 volts AC or more at 4000 RPM. A faulty
winding will show as a much lower reading than a good one and the Stator will
require replacement.
Should you require a replacement, then the Stator fitted to the Ninja 650R (ER-
6F) and ER-6N is a Kawasaki Part Number: 21003-0041 however Kawasaki advise
that from 2007 this was superseded by Part Number: 21003-0042. There is no
information regarding the reasons for this change.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
The Stator fitted is unique to the Ninja 650R (ER-6F), ER-6N and Versys models.
From the Kawasaki website P/N 21003-0041 & -0042 are fitted to the following
Kawasaki models:
Ninja 650R /ER-6F (EX650) 2006-2010
ER-6N (ER650) 2006-2010
Versys (KLE650) 2007-2010
Aftermarket Stators are manufactured and supplied by very few vendors, links to
these are located on the website in the Electrical links section.
Another option is to rewind your existing stator, this has been accomplished by a
number of owners using this article from The GS Resources website:
http://www.thegsresources.com/garage/gs_statorrewind.htm
It appears to be a reprint of the original article from the Suzuki Cavalcade website
here:
http://www.suzukicavalcade.com/Maintenance/stator.htm
The Regulator/Rectifier
As mentioned previously the Regulator/Rectifier (R/R) performs two functions,
firstly the Rectifier section uses diodes to rectify AC voltage from the Alternator
converting it to a useable DC voltage. Then the Regulator section regulates the
high DC voltage down to provide a steady 12-14 volts DC for system services and
charging the battery.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
1. To check the diodes in the R/R use the multimeter selected to Ohms ( range)
and measure the resistance of pins W/BL to BK1 then swap the leads of the
multimeter over and repeat the test. If the R/R is OK then there will be a low
resistance in one direction and high resistance in the other.
Repeat the test for pins W/BL to BK2 & BK3 and then for pins BK/Y to BK1, BK2 &
BK3. Again if the R/R is OK then there will be a low resistance in one direction
and high resistance in the other.
Regulator/Rectifier electrical connector
Rectifier Circuit Diagram
The resistance should be low in one direction and more than ten times as much in
the other direction. If any two leads are low or high in both directions, the diode
is defective and the R/R should be replaced.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Regulator/Rectifier
Regulator/Rectifier
Other information that may assist:
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
2. The Service Manual also details another series of tests that can be carried out
on the R/R to confirm serviceability. These tests confirm the serviceability of the
Regulator section using three 12 volt batteries and a test lamp. Due to the
complexity of these tests and the equipment requirements it is often quicker and
easier to swap with a known serviceable R/R if the Regulator section is suspect.
The Service Manual procedure is repeated below for completeness.
To test the regulator out of circuit, use three 12 Volt batteries and a test light (12
Volt, 3~6 Watt bulb in a socket with leads).
CAUTION - The test light works as an indicator and also a current limiter
to protect the regulator/rectifier from excessive current. Do not use an
ammeter instead of a test light.
Check to be sure the rectifier circuit is normal before continuing. See test (1.),
above.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Do the 1
st
step regulator circuit test.
Connect the test light and the 12 Volt battery to the R/R as shown.
Check the BK1, BK2 and BK3 terminal respectively.
If the test light turns on, the R/R is defective. Replace it. If the test light does
not turn on, continue the test.
Do the 2
nd
step regulator circuit test.
Connect the test light and the 12 Volt battery in the same manner as specified in
the Regulator Circuit Test-1
st
Step.
Apply 12 Volt to the voltage BR terminal. Check the BK1, BK2 and BK3 terminal
respectively.
If the test light turns on, the R/R is defective. Replace it. If the test light does
not turn on, continue the test.
Do the 3rd step regulator circuit test.
Connect the test light and the 12 Volt battery in the same manner as specified in
the Regulator Circuit Test-1
st
Step.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
Momentarily apply 24 Volt to the voltage BR terminal by adding a 12 Volt battery.
Check the BK1, BK2 and BK3 terminals respectively.
CAUTION - Do not apply more than 24 Volts. If more than 24 Volts is applied,
the Regulator/Rectifier may be damaged. Do not apply 24 Volts more than a few
seconds. If 24 Volts is applied for more than a few seconds, the
Regulator/Rectifier may be damaged.
If the test light did not light when the 24 Volt was applied momentarily to the
voltage monitoring terminal, the R/R is defective. Replace it.
If the R/R passes all of the tests described, it may still be defective. If the
charging system still does not work properly after checking all of the components
and the battery, test the R/R by replacing it with a known good unit.
Should you require a replacement, then the R/R fitted to all years of the Ninja
650R (ER-6F) and ER-6N is a Kawasaki Part Number: 21066-1127 but other part
numbers (SH678A-12) on the R/R identify it as being manufactured by the
Shindengen Electric Mfg Co.
From the Kawasaki website: P/N 21066-1127 is fitted to the following Kawasaki
models:
Ninja 650R /ER-6F (EX650) 2006-2010
ER-6N (ER650) 2006-2010
Versys (KLE650) 2007-2010
Z750 (ZR750) 2005-2010
Z1000 (ZR1000) 2003-2010
Vulcan 900 (VN900) 2006-2010
Brute Force 750 4x4 (KVF750) 2005-2007
Brute Force 650 4x4 (KVF650) 2007-2008
Mule 4x4 (KAF620) All years
Searches on the Internet indicate that the Shindengen P/N SH678A-12 is fitted to
a variety of makes including the Suzuki V-Strom and some Yamaha models. A
search on Google with this P/N reveals the full extent of its use.
Aftermarket R/Rs are manufactured and supplied by a number of vendors, links
to these are located on the website in the Electrical links section.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
The Regulator/Rectifier Connector
A number of posts on internet forums suggest that the fault with this connector is
due to water ingress. Certainly its location is not ideal due to its proximity to the
rear wheel. Supposedly Kawasaki made improvements from 2007 and later
models as the harness was re-routed to prevent water pooling in the connector.
Given that a number of owners with post 07 models who have suffered the same
fault I wouldnt bet on this being the complete solution.
Regulator/Rectifier Connector
Regulator/Rectifier Connector
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
The electrical connector website Eastern Beaver has advised that the logo on the
Regulator/Rectifier connector is a Japanese company called Furukawa Electric Co.
Eastern Beaver stock a range of Furukawa connectors and should be able to
supply a complete replacement connector or an individual pin.
http://www.easternbeaver.com/Main/Elec__Products/Connectors/Sealed/FKWH/fk
wh.html
Replacement parts - Furukawa Electric Co.
The Headlight Relay
As previously mentioned many owners who have experienced charging system
issues have also experienced headlight issues. After replacing the headlight
bulbs, the fault still exists. Further trouble-shooting identifies that the headlight
relay is at fault. The headlight relay is part of the Relay Box and it also contains
3 diodes. Unfortunately the headlight relay and diodes cannot be replaced
individually and the relay box is sold as a complete unit.
The diode arrangement is used as an electrical latch to operate the daylight
headlight system. This system is where the headlight does not operate when the
ignition switch is turned on, but operates when the engine is started and the
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
starter button is released. The headlight remains on (latched) until the ignition is
switch is turned off.
You can test the circuit of the headlight relay and the diodes which in my opinion
is the most likely cause of any headlight relay malfunction.
1. Remove the relay box from the bike.
2. Check the headlight relay circuit portion of the relay box by connecting a
multimeter (set to range) between terminals 1 and 3 (see the diagram above).
The multimeter should read open circuit (There should be an open circuit with
infinite resistance (multimeter displays dashed lines or the abbreviation "OL"
which stands for "open loop" or infinity - !). If the multimeter does not read as
specified, replace the relay box.
3. Check the headlight diode portion of the relay box by connecting a multimeter
(set to range) between terminals 1 and 11, then swap the multimeter leads
over. Repeat for terminals 2 and 11 (see the diagram above). The resistance
should be low in one direction and more than ten times as much in the other
direction. If any diode shows low or high in both directions, the diode is defective
and the relay box must be replaced.
Should you require a replacement, then the Relay Box initially fitted to the Ninja
650R (ER-6F) and ER-6N was a Kawasaki Part Number: 27002-0001 however
Kawasaki advise that this part has been superseded by Part Number: 27002-
0007. Again there is no information regarding the reasons for this change.
From the Kawasaki website: P/N 27002-0007 is fitted to the following Kawasaki
models:
Ninja 650R /ER-6F (EX650) 2006-2010
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource
ER-6N (ER650) 2006-2010
Versys (KLE650) 2007-2010
Vulcan 900 (VN900) 2006-2010
Vulcan 1700 (VN1700) 2009-2010
Vulcan 2000 (VN2000) 2006-2010
Concours 1400 (ZG1400) 2008-2010
Z750 (ZR750) 2007-2010
Z1000 (ZR1000) 2007-2010
Ninja ZX-6R (ZX600) 2006-2010
Ninja ZX-6R (ZX636) 2006
Ninja ZX-10R (ZX1000) 2006-2010
Ninja ZX-14 (ZX1400) 2006-2010
Disclaimer: This information is presented with no liability or guarantees
expressed or implied, work at your own risk.
Kawasaki Ninja 650R (ER-6F) & ER-6N Resource