Addpac GSM CLI Manual Guide - Eng

VoiceFinder GSM Gateway
[CLI Command Manual]

Oct, 2010

AddPac Technology
www.addpac.com
VoiceFinder GSM Gateway CLI Manual V1.01

AddPa AddPac Technology Proprietary & Documentation 56 - 2

AddPac GS3000 GSM Gateway

Note.
Product information can be changed at any time without notice. The information in this guide is provided as it is. It
does not assure any kind of guarantee implicitly and explicitly under all circumstances. Regard of this solution guide,
AddPac Technology and AddPac Technology solution supplier never guarantees the marketability and suitability of
particular use, not invasive including; trade, usage, implicitly and explicitly. Yet, the feature on technological standard,
and the information for the product guarantee and supply needs further consultation.


[ Contents ]

Chapter 1. Interface Connection ............. 6
Async Serial Interface Connection ................................................................................ 6
Ethernet Interface Connection ....................................................................................... 7
Chapter 2. Proper Operation check ......... 8
Booting Process and Operation Principle ...................................................................... 8
Use Console Terminal by Using HyperTerminal ........................................................... 14
APOS Command Usage ................................................................................................ 18
Administrator Mode Command ................................................................................... 19
Basic Setup..................................................................................................................... 20
APOS Upgrade ............................................................................................................... 21
Chapter 3. Console Command ............. 23
Basic Command for Network Setup ............................................................................. 23
Command for VoIP Protocol [H.323] ............................................................................ 25
Command for VoIP Protocol [SIP] ................................................................................. 31
Command for VoIP Protocol [Monitoring] ................................................................... 35
GSM Command [Call] ................................................................................................... 37
GSM Command [Black / White List] ............................................................................. 41
GSM Command [Callback Service] ............................................................................ 43
GSM Command [LCR(Least Cost Routing)] ................................................................. 46
GSM Command [Rest] ................................................................................................ 48
Command for GSM [Monitoring] .................................................................................. 51
Chapter 4. Appendix .......................... 53
Console Port Signal and Pin Out ................................................................................... 53


[ Chart ]

<Chart 2-1> Administrator Mode Command ......................................................................... 19
<Chart 4-1> Console Port Pin Out ............................................................................................. 53
<Chart 4-2> Series Ethernet Cable Signal and Pin Out .......................................................... 54


[ Picture Contents ]

<Picture 1-1> GS3000 Async Serial Interface Connection ...................................................... 6
<Picture 1-2> GS3000 LAN0/LAN1 Interface connection ........................................................ 7
<Picture 2-1> MS-Windows Terminal Emulator HyperTerminal .............................................. 14
<Picture 2-2> Enter Connecting Name in HyperTerminal ..................................................... 15
<Picture 2-3> Setup Value when connecting console cable to serial port ....................... 16
<Picture 2-4> COM1 Port Setup Example ................................................................................ 17
<Picture 2-5> APOS Image File Upgrade by Using FTP .......................................................... 21
<Picture 4-1> 100Base-TX RJ-45 Connector ............................................................................. 54
<Picture 4-2> Digital E1/T1 RJ45 Pin Out................................................................................... 55



Chapter 1. Interface Connection

Async Serial Interface Connection
Connect RS-232C Serial Console cable RJ-45 standard connector to console port. Connect
serial port such as GS3000 control PC to opposite side serial connector.

<Picture 1-1> GS3000 Async Serial Interface Connection



Ethernet Interface Connection
For internet connection WAN interface, connect with WAN device (router or ADSL/cable
modem) LAN interface and RJ45 standard UTP cable. Cross over may be used when
connecting to the router or modem directly. Use direct-through cable when connecting to
HUB.
Connect LAN0/LAN1 fast Ethernet interface by using RJ-45 connector.

User PC
RJ45 to RJ45
UTP Cable
WAN
(IP Network)

<Picture 1-2> GS3000 LAN0/LAN1 Interface connection



Chapter 2. Proper Operation check

Booting Process and Operation Principle
Following step shows booting process of GS3000.

Gateway checks the CPU, memory, and interface.

Boot Loader will be executed and find appropriate gateway s/w image file. Gateway is
designed to upload s/w in default configuration.

If s/w image file cannot be found in flash memory, boot loader will wait in boot mode
until it downloads the proper gateway s/w. (Use TFTP or FTP protocol to download proper
Next700 s/w)

After gateway loading, gateway will be operated in accordance with saved information.
Gateway will run with initial value if there is no saved setup information. For normal
network operation, administrator must setup pertinent details.

After GS3000 installation and interface connection, power must be supplied. Make sure to
connect power cable with GS3000. Do not connect GS3000 after providing power cable. Also,
use 110V power cable if the power supply is 110V. GS3000 automatically recognizes both 110V
and 220V so using proper power cable and additional operation is not necessary.


Following message shows after normal booting.

(Example) AP-GS3000 Booting Process
System Bootstrap, Version 1.2
Decompressing the image:
###################################[OK]

System Boot Loader, Version 5.2.9
Copyright (c) by AddPac Technology Co., Ltd. Since 1999.

[DUAL-BOOT] Start application (0xf1000100)...

System Bootstrap, Version 1.2
Decompressing the image:
###############################################################
###############################################################
###############################################################
#########[OK]

VoiceFinder Router Series (GS3000_G2)
Serial Number: GS3000_G2-fffe30
32BIT RISC Processor With 333MHz Clock
128 Mbytes System Memory
512 Kbytes System Boot Flash Memory
16 Mbytes System Flash Memory

1 RS232 Serial Console Interface

System main board ID is 0x0

GS3000_G2 System software Revision 8.41.03T
Released at Fri Jul 23 10:11:57 2010
Program is 3497304 bytes, checksum is 0x1bdc47c6

Local Time : Wed Jul 28 11:48:19 2010
Copyright (c) by AddPac Technology Co., Ltd. Since 1999.


SLOT[0] DETECT, ID(0x4)
Allocating system mbuffer counter: 6144
Kernel callwheelmask 0x3ff callwheelsize 1024
Loading file system(ver2.2), flash-base: 0xffff0000 ram-base: 0x038499bc
System utilization reference (28/28/28/28)
Start Target Debug Server
Attach FastEthernet Interface at Slot 0, Port 0-1, <0-0>/<0-1>
FastEthernet0/0: link is up 100 Mbps (full duplex)
Interface FastEthernet0/0, changed state to UP
Interface FastEthernet0/1, changed state to DOWN
Hardware Revision ID = 0
Line Card equip status = 0xe00
Slot (0) cardId=0 subId=4
Slot (0) AP-N1-GSM4 : VoIP module 4 GSM (New 1)


Slot (0) Module type : GSM

RTA_Daemon start
GsSim Start
Start File Transfer Protocol Server (listen tcp/21)
Wait init0........................................Wait
init0..............................................................................................................................................................
........................................................................................................................................

VOIP_INTERFACE_DOWN
Not Available: status(1) interface(0)
VOIP_INTERFACE_UP : (172.17.114.130)
Not Available: status(1) interface(0)
The port is not available
GsSim Ready

Press RETURN to get started.

RTA Module Ready
DSP S/W download (0): .... OK

QS (0) install ... OK

Gatekeeper shutdowned.

VoIP in service.
GSM-0/0: MODULE ID = MULTIBAND 900E 1800
GSM-2/3: MODULE ID = MULTIBAND G850 1900

GSM-0/0: SIM READY
GSM-0/1: SIM READY
GSM-0/2: SIM READY
GSM-0/3: SIM READY
Interface GSM-0/0, changed state to UP

Welcome, APOS(tm) Kernel Version 8.41.03T.
Copyright (c) 1999-2010 AddPac Technology Co., Ltd.

Login:
Password:

When log-in message shows at the end, enter basic log-in value root and basic password
value router then log-in is completed. After log-in procedure, prompt Router> is displayed
in console terminal.

Prompt which displays on VoiceFInder GSM Gateway includes: router> and router#. If
prompt is displayed as >, logged-in user has other authority other than admin. A user
cannot use command which changes gateway setup and a user only has minimum
authority. If the prompt is displayed as #, current logged-in user has admin authority and
uses all gateway functions.

If you log in as Admin, Admin cannot change all gateway setup. So, we recommend to
change admin account password basic value for security.


Use Console Terminal by Using HyperTerminal
Terminal Emulator Application must be setup if PC is being used as console terminal. It uses
Hyper Terminal Application when using MS-Windows.

<Picture 2-1> MS-Windows Terminal Emulator HyperTerminal


Setup a new connection name after running HyperTerminal. Setup name can be decided
as you like. We will decide as AddPac.

<Picture 2-2> Enter Connecting Name in HyperTerminal



Now, we setup interface which is connected to console cable.
Console Cable is usually connected to PC RS-232C 9Pin Serial Port. Choose a right port in
accordance with user environment. We will connect to COM1.

<Picture 2-3> Setup Value when connecting console cable to serial port



We setup each setup values in interface registration information. We make COM1 as
standard.

Bits Per Second Data bits Parity Stop bits Flow Control
9600 8 None 1 None

<Picture 2-4> COM1 Port Setup Example
Booting message shows on Hyper Terminal after setup.


APOS Command Usage

NOTE AddPac technology devices are all equipped with APOS (AddPac Operating
System). So basic CLI (Command Line Interface) environments are all identical.

All command in gateway can be connected to console or telnet terminal (VT-100 terminal).
Command provides to view system restriction items, user mode to provide access function,
look at the system status. Administrator mode to use system debuggin function and change
the setup environment or setup a new environment.

Following characteristics are gateway related command input.

It automatically recognizes without typing all command. For example, to run show
command, type sh or sho. It will automatically recognizes as show

It provides on-line help function so that when user enters incorrect system command,
possible items and commands will be shown.

More function provides to display unable information on screen.

It provides Help and ? function to display all possible command and explanation.

It provides History function. User may use Prompt number without retyping command.

System command structures are divided into 3 modes. Each mode has different
command. Command for each mode is as below.



Administrator Mode Command
Administrator mode command can only be used for logged-in administrator. To access
system setup mode under looged-in administrator mode. In this mode, it shows more
information in accordance with options.
You may use all command in administrator mode.

Administrator mode prompt is displayed as GS3000#.

<Chart 2-1> Administrator Mode Command
Command Explanation
clear Command to initialize interface counter, statistics
configure Enter as setup mode
copy Copy running config as startup config
debug Overall system debug Command
disconnect Command to close VTY connection
end Enter as administrator mode
erase Delete config file
exit Move to previous step
ftp Access ftp client
help View APOS Help
no Command to delete current setup
ping Network connection confirmation tool
reboot System rebooting command
show
Command to view the system operation status and setup
status
telnet telnet access command
tftp Command to send file to tftp server
traceroute Command to check IPv4 routing route
who Command display accessed user with vty
write Command to save operating configuration
undebug Command to deactivate the activated debug
user Command to add/modify/delete system user



Basic Setup

Host Name Setup
You may change prompt name in CLI environment when you access into console or telnet.
Host name considers as very important when you manage several devices with telnet
access.

Router# configure terminal
Router(config)#
Router(config)# hostname {name}
Router(config)#

Clock Setup
Setup system time. You should set it correctly because this time will be displayed on system
operation time, debug and log.

Router(config)#
Router(config)# clock {Year} {Month} {Day} {Hour} {Minute} {Second}
Router(config)#

User Management
User management can be used when accessing telnet, FTP, and SAMBA. You may have to
use user password/ID which is known to administrator and if it is exposed to others, device
would not operate as it is.

Router(config)#
Router(config)# username {add} <login-name> <password> {admin|high|normal|low}
Router(config)#



APOS Upgrade
AddPac Gateway products allow FTP method approach for APOS image file transmit. Also,
a relevant protocol can independently on/off the service.

AddPac GSM Gateway upload/download network configuration is as below.

<Picture 2-5> APOS Image File Upgrade by Using FTP

FTP Service Activation
Activate FTP service first to execute the APOS upload/download.

Router(config)#
Router(config)# ftp server
Router(config)#



APOS Upload
Upload gateway APOS in PC with ftp.

D:\ >dir
2007-11-15 05:21p <DIR> .
2007-11-15 05:21p <DIR> ..
2007-11-15 05:21p 3,098,820 GS3000_v8_51_001.bin

D:\>
D:\> ftp 172.17.201.115
Connected to 172.17.201.115.
220 GS3000 FTP server (Version 8.51) ready.
User (172.17.201.115:(none)): root
331 Password required for root.
Password:
230 User root logged in.
ftp> binary
200 Type set to I.
ftp>
ftp> put GS3000_g2_v8_51_001.bin
200 PORT command successful.
150 Opening BINARY mode data connection for ' GS3000_g2_v8_51_001.bin '.
226 Transfer complete.
ftp: 3098820 bytes sent in 2.47Seconds 1039.51Kbytes/sec.
ftp> quit
221 Goodbye.
D:\>



Chapter 3. Console Command

Basic Command for Network Setup

Command to confirm after IP, default route setup
Following configuration shows network setup for basic communication which identifies the
proper network connectivity with default gateway ping test.

Router(config)# interface FastEthernet 0/0
Router(config-if)# ip address 172.17.201.115 255.255.0.0
Router(config-if)# exit
Router(config)# ip route 0.0.0.0 0.0.0.0 172.17.1.1
Router(config)# end
Router#
Router#
Router# write
Do you want to WRITE configuration ? [y|n] y
Writing configuration....done
Router#
Router# ping 172.17.1.1
PING 172.17.1.1 (172.17.1.1): 56 data bytes
64 bytes from 172.17.1.1: icmp_seq=1 ttl=255 time=2 ms

--- 172.17.1.1 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 1.73/2.027/2.75 ms
Router#


PPPoE Configuration
Step Command Explanation
1
# configure terminal
(config)#
Change to APOS command input mode.
2
(config)# interface fastethernet 0/0
(config-if)#
Start fast Ethernet 0/0 setup.
3 (config-if)# no ip address No IP address setup.
4 (config-if)# pppoe enable Activate network protocol PPPoEdmf.
5 (config-if)# encapsulation ppp Assign network protocol as PPP.
6 (config-if)# ppp authentication pap callin Setup PPP certification method as PAP.
7 (config-if)# ppp ipcp default-router
Setup to receive default router IP address from PPP
server.
8 (config-if)# ppp ipcp dns request Setup to receive DNS IP address from PPP server.
9
(config-if)# ppp pap sent-username addpac
password 1234
Setup PAP user ID as addpac, password as1234.

DHCP Configuration
1
Enter configuration commands, one per line. End
with CNTL/Z
(config)#
2
(config-if)#
Start setting up fast Ethernet interface 0/0.
3
(config-if)# ip address dhcp
(config-if)#
Setup to assign IP address through DHCP client setup.



Static IP Configuration

1
Enter configuration commands, one per line. End with CNTL/Z
(config)#
2
(config-if)#
Start setting up fast Ethernet interface 0/0.
3 (config-if)# ip address 192.168.1.2 255.255.255.0 Setup IP address.
4 (config-if)# ip route 0.0.0.0 0.0.0.0 192.168.1.1 Setup default router.

Command for VoIP Protocol [H.323]

H.323 Peer to Peer


A necessary gateway setup parameter is as follow.
Gateway IP Address / Dial-peer Voip / Dial-peer Pots / VoIP Interface

1
HQ(config)# dial-peer voice 0 pots
HQ(config-dialpeer-pots-0)#
Assign serial number 0 to physical voice interface to
set one phone line. (Serial number can be assigned
from 0 to 65,535, normally assign from 0 when
setting voice interface)
2
HQ(config-dialpeer-pots-0)# destination-
pattern 8425683848
Grant phone number to assigned serial number 0.
3 HQ(config-dialpeer-pots-0)# port 0/0
Setup VoIP physical voice port which responds to
assigned serial number 0. (voice port types are may
vary depending on devices)
4
HQ(config-dialpeer-pots-0)# dial-peer voice
1000 voip
HO(config-dialpeer-voip-1000)#
To setup one VoIP call, setup serial number 1000 to
VoIP interface serial number. (Serial number can be
assigned from 0 to 65535. Assign from 1000 when
setting VoIP interface.)
5
HQ(config-dialpeer-voip-1000)# destination-
pattern 8325683848
Grant phone number 8325683848 to assigned serial
number 1000.
6
HQ(config-dialpeer-voip-1000)# session target
ip 193.168.1.2
Send VoIP call setup to assigned serial number 1000
with gatekeeper.
7
HQ(config-dialpeer-voip-1000)# dtmf-relay
h245-alphanumeric
Setups DTMF transmit method as H.245
Alphanumeric to assigned serial number 1000.

8
HQ(config-dialpeer-voip-1000)# dial-peer voice
1001 voip
To setup other VoIP call, assign serial number 1001 to
VoIP interface.
9
pattern 82T
Setup if the phone number starts with 82 to assigned
serial number 1001.
10
HQ(config-dialpeer-voip-1001)# session target ip
192.168.1.2
Send VoIP call setup with 192.168.1.2 to assigned
serial number 1001.
11
h245-alphanumeric
Alphanumeric to assigned serial number 1001
(default).
12 HQ(config)# voip-interface ip fastethernet 0/0 Setup VoIP interface as fast Ethernet port. (Default).
13
HQ(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.1
HQ#
Setup default router as 192.168.1.1.
14
HQ(config)# exit
HQ#
Exit from APOS command input mode.



H.323 Gatekeeper



1 HQ(config)# dial-peer voice 0 pots
Assign serial number 0 to physical voice interface
for setting up one phone line. (serial number can be
assigned from 0 to 65,535. For voice interface
setup, it usually starts from 0)
2
HQ(config-dialpeer-pots-0)# destination-
pattern 8225683848
Grant phone number to assigned serial number 0.
3 HQ(config-dialpeer-pots-0)# port 0/0
Set VoIP device physical voice port which responds
to assigned serial number 0. (Voice port
types/numbers are may vary.)
4
1000 voip
Set serial number 1000 to VoIP interface for VoIP
call setup. (serial number can be assigned from 0 to
65535. Assign from 1000 for VoIP interface setup.)
5
pattern 8325683848
Grant phone number 8325683848 to assigned serial
number 1000.
6
ras
Send VoIP call setup to assigned serial number
1000 with gatekeeper.
7
h245-alphanumeric

8
HQ(config-dialpeer-voip-1000)# dial-peer voice
1001 voip
Assign serial number 1001 to VoIP interface for VoIP
call setup.
9
pattern 82T
Setup it the phone number starts with 82 to
assigned serial number 1001.
10
ras
Send VoIP call setup to assigned serial number
1001 with gatekeeper.
11
h245-alphanumeric
Setup DTMF transmission method as H.245
12 HQ(config-dialpeer-voip-1001)# gateway Change to external gatekeeper setup mode.
13 HQ(config-gateway)# h323-id addpac-BB Setup H.323 ID.
14 HQ(config-gateway)# gkip 199.168.1.1 1719 128 Setup external gatekeeper IP address.
15 HQ(config-gateway)# register Register in external gatekeeper.
16
HQ(config-gateway)# voip-interface ip
fastethernet 0/0
Set VoIP interface as Ethernet 0.0 port.
17
HQ(config)# exit
HQ#
Exit from APOS command input mode.



Command for VoIP Protocol [SIP]

SIP Peer to Peer

View SIP Related Command
1
# config
(config)#
Enter as APOS command setup mode.
2
(config)# sip-ua
(config-sip-ua)# ?
Enter as SIP user agent command setup mode
and confirm command with ?

no set to default configuration
Delete command which is already setup in SIP
user agent.

register try registration to sip registrar Try to register in SIP-Server.


signaling-port set SIP signaling port (default 5060) Change SIP signaling port. (Default: 5060)

sip-server Configure a SIP Server Interface Enter SIP Server IP address or DNS server.

sip-username Set Username of SIP User Agent Register SIP user name.

sip-password Set Password of SIP User Agent Register SIP password.

timeout Set timeout value Setup register retry timeout value.

end Go to Top menu Return to administrator mode.

exit Exit from the EXEC Return to APOS command setup mode.

1
1000 voip
Assign serial number 1000 to VOIP interface
for VoIP call setup. (serial number can be
assigned from 0 to 65535. Assign from 1000
for VoIP interface setup.)
2 HQ(config-dialpeer-voip-1000)# destination-pattern T

3
HQ(config-dialpeer-voip-1000)# session target ip
192.168.1.2
Setup VoIP destination address as 192.168.1.2
which responds to destination pattern.
4
HQ(config-dialpeer-voip-1000)# session
protocol sip
Setup VoIP protocol as SIP which is relevant
to destination pattern. If you setup as no
protocol sip, it will send to h.323 message.
5
rtp-2833
Send DTMF transmission method with
RFC2833 RTP payload to assigned serial
number 1000. (currently, SIP mode only offers
2833 for dtmf signal).



SIP SIP Server

SIP Proxy Server Configuration
1 HQ(config)# dnshost nameserver 199.168.1.2 Register DNS server IP.
2 HQ(config-dialpeer-pots-0)# dial-peer voice 1000 voip
Assign serial number 1000 to VoIP interface for
VOIP call setup. (serial number can be assigned

from 0 to 65535. Assign from 1000 for VoIP
interface setup.)
3 HQ(config-dialpeer-voip-1000)# destination-pattern T

4 HQ(config-dialpeer-voip-1000)# session target sip-server
Setup VoIP destination address as SIP server
5 HQ(config-dialpeer-voip-1000)# session protocol sip
Setup VoIP protocol as SIP which is relevant to
destination pattern. If you setup no protocol
sip, it will send to h.323 message.
6 HQ(config-dialpeer-voip-1000)# dtmf-relay rtp-2833
Send DTMF transmission method with RFC 2833
RTP payload to assigned serial number 1000
(Currently, 2833 only provides dtmf signal in
SIP mode).
7 HQ(config-dialpeer-voip-1000)# sip-ua Enter as SIP UA setup mode
8 HQ(config-sip-ua)# sip-username 8425683848 Register SIP user name
9 HQ(config-sip-ua)# sip-password AddPac-HQ Register password
10 HQ(config-sip-ua)# sip-server 192.168.1.1
Setup SIP server IP (DNS server must be setup if
you set up as domain name)
11 HQ(config-sip-ua)# register e164 Register to SIP server as E.164.


Command for VoIP Protocol [Monitoring]

VoIP - Monitoring command
1 Router# show voice port <slot> <port> / all / summary Check voice port information
2 ROUTER# show run Check all setup information
3 ROUTER# show sip Check SIP register status and gateway value
4 ROUTER# show gateway Check H.323 register status and gateway value
5 ROUTER# show version Check gateway version
6 ROUTER# show clock Check gateway current time/running time
7 ROUTER# show interface Check gateway interface status
8 ROUTER# show dial-peer voice run / summary Check Dial-peer setup information
9 ROUTER# show username Check gateway account ID / PW



VoIP - Debugging command
1 ROUTER# debug voip call Debug On for VoIP call
2 ROUTER# debug rta ipc Debug On for port
3 ROUTER# debug voip sip Debug On for SIP
4 ROUTER# debug voip h225-asn1 Debug On for H.225
5 ROUTER# debug voip h245-asn1 Debug On for H.245
5 ROUTER# terminal monitor Activate monitoring for Debug Commands
5 ROUTER# no debug all Debug Off


GSM Command [Call]
SIP
H.323
IP Network
(WAN)
Concurrent Triple VoIP Stack
Voice
GSM
Network

GSM - FXS to GSM Call
Outbound Call (1 Stage)
: Making call to mobile phone from analog phone connected to FXS directly.
Outbound Call (2 Stage)
: Making call to mobile phone from analog phone connected to FXS after hearing of 2
nd
dial
tone from AP-GS1002



1
AP-GS1004(config)# dial-peer voice 1 pots
AP-GS1004(config-dialpeer-pots-1)#
Assign serial number 1 to physical voice
interface for phone line setup (serial number
can be assigned from 0 to 65,535. Assign from 0
for voice interface setup.)
2 AP-GS1004(config-dialpeer-pots-1)# destination-pattern T
Grant phone number to assigned serial
number1.
3 AP-GS1004(config-dialpeer-pots-1)#Port 1/0
Set physical GSM port which responds to
assigned serial number 1. (Voice port
types/numbers may vary)
4
AP-GS1004(config)# exit
AP-GS1004#
Exit from input mode.



GSM - VoIP to GSM Call

1
AP-GS1004(config)# dial-peer voice 0 pots
AP-GS1004(config-dialpeer-pots-0)#
Assign serial number 0 to physical voice interface
for phone line setup. (serial number can be
assigned from 0 to 65,535. Assign from 0 for
voice interface setup.)
2 AP-GS1004(config-dialpeer-pots-0)# destination-pattern T Grant phone number to assigned serial number 0.
3 AP-GS1004(config-dialpeer-pots-0)# port 1/0
Set physical GSM port to assigned serial number 0.
(Voice port types/numbers are may vary)
5
AP-GS1004(config)# dial-peer voice 1000 voip
AP-GS1004(config-dialpeer-voip-1000)#
Assign serial number 1000 to VoIP interface for
VOIP call setup. (serial number can be assigned
from 0 to 65535. Assign from 1000 for VOIP
interface setup.
6
AP-GS1004(config-dialpeer-voip-1000)#destination-pattern
T
It means all input numbers.
7
AP-GS1004(config-dialpeer-voip-1000)#session target ip
194.168.1.3
Setup VoIP destination address as 192.168.1.2
8 AP-GS1004(config)# session protocol sip
Setup VoIP protocol as SIP which responds to
destination pattern. If you setup as no protocol
sip, it will send to h.323 message.
9 AP-GS1004(config)# dtmf rtp-2833 Send DTMF transmission method as RFC 2833

RTP payload to assigned serial number 1000
(Currently, 2833 only provides dtmf signal in SIP
mode).
10
AP-GS1004#
Exit from input mode



GSM Command [Black / White List]

GSM - Black / White List

1
AP-GS1004(config)# dialpattern-group 0
AP-GS1004(config-dialpattern-group#0)#
Create Black List Group.
2 AP-GS1004(config-dialpattern-group#0)# pattern 0 1000 Enter pattern number which is relevant to Black List.
3 AP-GS1004(config-dialpattern-group#0)# exit Return to configuration mode.
4 AP-GS1004(config)# voice-port 1/0 Enter to applicable port.
5
AP-GS1004(config-voice-port-1/0)# gsm inbound black
list-group 0
Apply regarding inbound call.
6
AP-GS1004(config-voice-port-1/0)# gsm outbound black
list-group 0
Apply regarding outbound call.
7
Create White List Group.
8 AP-GS1004(config-dialpattern-group#0)# pattern 0 2000 Enter patter number which is relevant to White List.
9 AP-GS1004(config)# voice-port 1/0 Enter to applicable port.
10 AP-GS1004(config-voice-port-1/0)# gsm inbound white Apply regarding inbound call.

list-group 1
11
AP-GS1004(config-voice-port-1/0)# gsm outbound white
list-group 1
Apply regarding outbound call.
12
AP-GS1004(config-voice-port-1/0)# exit
AP-GS1004(config)#



GSM Command [Callback Service]

GSM - WEB Callback
WEB Callback Sample Configuration
!
hostname AP-GS1004
!
interface fastethernet 0/0
ip address 194.168.1.2 255.255.255.0
!
ip route 0.0.0.0 0.0.0.0 194.168.1.1
! Gateway configuration
!
gateway
gsm-call-service-white-list-group 2
!
!
! Dial Pattern Group configuration.
!
dialpattern-group 2
pattern 0 1000
!

1
Create WEB Callback Group.
2 AP-GS1004(config-dialpattern-group#0)# pattern 0 1000 Enter the number for WEB Callback
4 AP-GS1004(config)# gateway Enter to gateway setup.
5
AP-GS1004(config-gateway)# gsm-call-service-white-list-
group 2
Apply WEB Callback Group

6
AP-GS1004(config)# gateway
AP-GS1004(config-gateway)# gsm-call-service 1000 2000
Execute WEB Callback.

GSM - GSM Callback
GSM Callback Sample Configuration
!
hostname AP-GS1004
!
ip address 194.168.1.2 255.255.255.0
!
ip route 0.0.0.0 0.0.0.0 194.168.1.1
! Voice port configuration
!
! GSM
Voice-port 1/0
gsm-call-back-white-list-group 3
!
! Dial Pattern Group configuration.
!
Dialpattern-group 3
pattern 0 2000
!

1
Create GSM Callback Group.
2
AP-GS1004(config-dialpattern-group#3)# pattern 0
2000
Enter GSM callback number.
4 AP-GS1004(config)# voice-port 1/0 Enter to Callback applicable port.
5 AP-GS1004(config-voice-port-1/0)# gsm-call-back- Apply callback.

white-list-group 3
6
AP-GS1004(config-voice-port-1/0)# exit
AP-GS1004(config)#
Exit.
7
AP-GS1004#



GSM Command [LCR(Least Cost Routing)]

GSM - LCR(Least Cost Routing)
LCR Sample Configuration
!
hostname AP-GS3000
!
ip address 194.168.1.2 255.255.255.0
!
ip route 0.0.0.0 0.0.0.0 194.168.1.1
! Time interval Group configuration.
!
time-interval-group 0
weekdays from 09:00 to 12:00
!
!
! LCR Tariff Group configuration.
!
lcr-tariff-group 0
time-interval-group 0
restore-limit daily
accounting-period first 5 other 10
free-quota voice 300
free-quota sms 100

1
AP-GS3000(config)# time-interval-group 0
AP-GS3000(config-tinterval-group#0)#
Create Time Interval Group.
2
AP-GS3000(config-tinterval-group#0)# weekdays from
09:00 to 12:00
Setup a date and time for LCR.
3 AP-GS3000(config-tinterval-group#0)# exit Exit.

4
AP-GS3000(config)# lcr-tariff-group 0
AP-GS3000(config-lcr-group#0)#
Create LCR Tariff Group.
5
AP-GS3000(config-lcr-group#0)# time-interval-
group 0
Apply previously setup Time Interval Group.
6 AP-GS3000(config-lcr-group#0)# restore daily Setup Restore. (everyday, every month )
7
AP-GS3000(config-lcr-group#0)# accounting-
period first 5 other 10
Create accounting regard of Voice Call.
8 AP-GS3000(config-lcr-group#0)# free-quota voice 300 Setup free phone call time
9 AP-GS3000(config-lcr-group#0)# free-quota sms 100 Setup free SMS number.
10
AP-GS3000(config-lcr-group#0)# exit
AP-GS3000(config)#
Exit.



GSM Command [Rest]

GSM - GSM Port Functions
Sample Configuration for GSM Band Selection
!
GSM 1/0
sim pin 1234
band-select gsm900
bts bcch 338
sms-language ascii
!
End

1
AP-GS3000(config)# gsm 1/0
AP-GS3000(config-gsm1/0)#
Enter to GSM Port.
2 AP-GS3000(config-gsm1/0)# sim pin 1234 Setup PIN Code. (When necessary)
3 AP-GS3000(config-gsm1/0)# band-select gsm900
Setup GSM Bandwidth.
(900 , 850, 1800, 1900)
4 AP-GS3000(config-gsm1/0)# bts bcch 338 Setup cell: Auto / Manual.
5 AP-GS3000(config-gsm1/0)# sms-language utf8 Setup SMS language.
6 AP-GS3000(config)# exit Exit.



GSM - SMS
1
AP-GS3000# gsm 1 0 sms message send <phone number>
<message>
Send SMS from GSM Port.
2 AP-GS3000# gsm 1 0 message list all Check SMS Message. (All / Unread / Read / Fail)
3 AP-GS3000# gsm 1 0 sms message delete all Delete SMS Message. (All / Partially)

GSM - USSD (Balance check of SIM Card)
1 AP-GS3000# gsm 1 0 ussd send *123# Check SIM Card Balance.

GSM - Radius
Sample Configuration for Radius
!
radius-server host 192.168.100.254 1813 1812
radius-server key addpac
radius-server retransmit 3
radius-server timeout 5
radius-server authentication voip-inbound
radius-server authentication username 1234 password 1234
radius-server accounting voip start-stop
! !
End

1
AP-GS3000(config)# radius-server host <ip address>
<accounting port> <authentication port>
Setup Radius Server IP address, Auth port,
Accounting port

2 AP-GS3000(config)# radius-server key addpac Setup Radius Server Password
3
AP-GS3000(config)# radius-server authentication voip-
inbound / voip-outbound / voip-bidirectional
Setup VoIP call direction for Radius
Authentication. Inbound / Outbound / Both
4
AP-GS3000(config)# radius-server authentication
username 1234 password 1234
Setup Authentication Username and password.
5
AP-GS3000(config)# radius-server accounting voip start-
stop / stop-only
Setup Accounting Type
Start-Stop / Stop-only
6 AP-GS3000(config)# radius-server retransmit 3 Number of retransmit time
7 AP-GS3000(config)# radius-server timeout 5 Setup Timeout (sec)



Command for GSM [Monitoring]

GSM - Monitoring command
1 AP-GS3000# show gsm sim-card Check sim card status of GSM Gateway
2 AP-GS3000# show gsm module status Check GSM module information and status
3 AP-GS3000# show gsm <slot> <port> cell-monitor Display cell information to slot/port
4 AP-GS3000# show gsm <slot> <port> check-dev Check device status to slot/port
5 AP-GS3000# show gsm <slot> <port> dev-info Check device information to relevant slot/port
(only be seen after debugging)
6 AP-GS3000# show gsm <slot> <port> imei Check IMEI to relevant slot/port
7 AP-GS3000# show gsm <slot> <port> imsi Check IMSI to relevant slot/port
8 AP-GS3000# show gsm <slot> <port> net-oper-id Check GSM Network Operator ID to relevant
slot/port
9 AP-GS3000# show gsm <slot> <port> phone-number Check sim number to relevant slot/port
10 AP-GS3000# show gsm <slot> <port> reg-status Check GSM registration status to relevant
slot/port
11 AP-GS3000# show gsm <slot> <port> rssi Check cell RSSI to relevant slot/port
12 AP-GS3000# show gsm <slot> <port> serv-cell-info Display cell information to relevant slot/port
13 AP-GS3000# show gsm <slot> <port> state Display operation status to relevant slot/port



GSM - Debugging command
1 AP-GS3000# debug gsm <slot><port> all Debug on regard of all GSM
2 AP-GS3000# debug gsm <slot><port> call Debug on regarding GSM call
3 AP-GS3000# debug gsm <slot><port> cmd Debug on regarding GSM command
4 AP-GS3000# debug gsm <slot><port> event Debug on regarding GSM event
5 AP-GS3000# debug gsm <slot><port> error Debug on regarding GSM error
6 AP-GS3000# debug gsm <slot><port> sms Debug on regarding GSM SMS


Chapter 4. Appendix

Console Port Signal and Pin Out

In this appendix, it explains the cable pin specification of GS3000.

Console port signal and pin out (RJ-45 to DB9)
UTP cable (RJ-45 to RJ-45) pin out
E1/T1 cable (RJ-45 to PBX) pin out

[ Console Port Signal and Pin Out ]

Use built-in RJ-45 to DB9 (Female DTE connector) to connect router console port
and PC which terminal emulator software runs.

<Chart 4-1> Console Port Pin Out
Console Port
(DTE)
RJ-45 DB-9
Console Device
(PC)
Signal RJ-45 Pin DB-9 Pin Signal
RTS 1 8 CTS
DTR 2 6 DSR
TxD 3 2 RxD
GND 4 5 GND
GND 5 5 GND
RxD 6 3 TxD
DSR 7 4 DTR
CTS 8 7 RTS



[UTP cable (RJ-45 to RJ-45) Pin Out]

Use RJ-45 to RJ-45 Ethernet cable to connect router and other devices (HUB). RJ-45 connector
pin order is shown in Picture 4-1.

<Picture 4-1> 100Base-TX RJ-45 Connector

<Chart 4-2> Series Ethernet Cable Signal and Pin Out
RJ-45 Signal Direction RJ-45 Pin
1 Tx + 1
2 Tx - 2
3 Rx + 3
4 - - 4
5 - - 5
6 Rx - 6
7 - - 7
8 - - 8

1. This specification is cable specification for series cable in between router and hub.
2. Use cross cable to directly connect router to PC or router to router.



[E1/T1 Cable (RJ-45 to PBX) Pin Out]

Addpac E1/T1 module can be connected with RJ45 cable. RJ45 pin
arrangement is as below. Connect PBX RX with RJ45 1,2 and TX with 3,4.

<Picture 4-2> Digital E1/T1 RJ45 Pin Out



AddPac Technology
2F, Kyeong-An Bldg., 769-12 Yeoksam-
Dong. Kangnam-gu, Seoul. 135-080
Phone (02) 568-3848
Fax (02) 568-3847
Email: [email protected]
Homepage: www.addpac.com

Addpac GSM CLI Manual Guide - Eng

Uploaded by

Copyright:

Available Formats

Addpac GSM CLI Manual Guide - Eng

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Addpac GSM CLI Manual Guide - Eng

Uploaded by

Copyright:

Available Formats

What are the main components of the GSM Gateway?

What are the different connection types described in the manual?

VoiceFinder GSM Gateway

[CLI Command Manual]

You might also like