Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    GE 175d2750g313

    Uploaded by

    Emmanuel Vieira Villasana
    The document provides step-by-step instructions for servicing various components of a washing machine, including removing the control panel, switches, timer, cover/lid assembly, tub/motor assembly, transmission, motor/clutch, and spin basket. Safety warnings are also provided to disconnect power before servicing and properly ground all electrical components.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    GE 175d2750g313

    Uploaded by

    Emmanuel Vieira Villasana
    2K views2 pages
    The document provides step-by-step instructions for servicing various components of a washing machine, including removing the control panel, switches, timer, cover/lid assembly, tub/motor assembly, transmission, motor/clutch, and spin basket. Safety warnings are also provided to disconnect power before servicing and properly ground all electrical components.

    Original Description:

    Manual de Lavadora GE

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides step-by-step instructions for servicing various components of a washing machine, including removing the control panel, switches, timer, cover/lid assembly, tub/motor assembly, transmission, motor/clutch, and spin basket. Safety warnings are also provided to disconnect power before servicing and properly ground all electrical components.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    2K views2 pages

    GE 175d2750g313

    Uploaded by

    Emmanuel Vieira Villasana
    The document provides step-by-step instructions for servicing various components of a washing machine, including removing the control panel, switches, timer, cover/lid assembly, tub/motor assembly, transmission, motor/clutch, and spin basket. Safety warnings are also provided to disconnect power before servicing and properly ground all electrical components.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    N.D.

    06L-2080
    1. Follow steps 4 & 5 .
    2. Remove ve hex screws from control panel
    bracket. Tilt bracket up and out of the way.
    (Water valve is mounted to bracket.)
    3. Disconnect four dampening straps from tub
    attached by 5/16" hex screws.
    4. To remove tub cover, lift out eight molded
    tabs and pull cover off.
    5. Remove agitator by grasping bottom and
    sharply pulling up.
    6. Remove 7/16" hex bolt attaching air bell
    coupling to transmission spline shaft.
    TIP: To align agitator to replace, match
    grooves in air bell to grooves inside agitator.
    Fin is aligned with groove.
    123C8381P001
    The power must be disconnected before servicing by unplugging the machine or
    disconnecting the circuit breaker.
    The machine must be electrically grounded through the grounding lead in the three-prong
    power cord. The cord must be plugged into a properly installed and grounded appliance
    outlet. If local codes require an additional ground connection, use a 16-gauge or larger wire
    to connect the washer cabinet to an established ground. In all cases the grounding method
    must comply with all local codes and ordinances.
    1. Follow step 1 .
    2. Pull knob off switch to be serviced.
    3. Using screwdriver, gently lift up tab.
    2 To Remove Switches in
    Control Panel:
    1 To Remove Control Panel:
    4 To Remove Front Panel:
    1. Locate two spring clips between cover and
    front panel by aligning putty knife with
    groove on either side of lid and cover. (See
    illustration below.)
    2. Insert putty knife and push forward to release
    clips.
    TO REDUCE THE RISK OF ELECTRICAL SHOCK:
    4. The motor and tub assembly will now lean
    forward after both front rod and spring
    assemblies are unhooked at the platform.
    5. Disconnect motor harness connector,
    grounding wire to frame and pressure switch
    hose at take off.
    6. Disconnect drain hose inlet (black hose) at
    tub.
    7. Lift and push bottom of tub/motor assembly
    towards the rear of the cabinet, and roll tub
    out under top lip of cabinet.
    8. Pull tub out of cabinet by lifting it over on its
    top as shown below.
    9. Reverse procedure to reassemble.
    9 To Service Transmission:
    1. Repeat steps 4 , 5 , 6 , 7 .
    2. Remove transmission drive pulley by holding
    belt as shown, and removing 3/4" pulley nut.
    3 To Remove Timer:
    1. Follow step 1 .
    2. Remove Timer Knob assemblies.
    3. Remove timer harness connector.
    4. Remove 1/4" hex screw mounting timer to
    bracket (if applicable).
    5. Lift tab and pull timer out to the left.
    6. Reverse procedure to reassemble.
    1. Remove front panel using step 4 .
    2. Remove two 1/4" hex screws on front of
    cabinet.
    3. Remove tape from lid switch connector and
    disconnect.
    4. Remove cover/lid assembly.
    5. Reverse procedure to reassemble.
    NOTE: Tape must be replaced on lid switch
    connector.
    5 To Remove Cover/Lid
    Assembly:
    3. Rotate front
    panel forward
    and lift off
    cabinet base
    locator tabs.
    4. Reverse
    procedure to
    reassemble.
    7. Remove left-
    handed 1-11/16"
    transmission
    hub nut.
    This nut is
    aluminum,
    take care not
    to round
    the edges
    when removing
    or replacing.
    TIP: The word LOOSEN with an arrow
    APPEARS ON THE NUT.
    8. Lift spin basket out and set aside.
    9. Reverse procedure to replace basket.
    1. Repeat steps
    4 , 5 , 6 .
    2. Remove split
    ring and
    washer from
    transmission.
    7 To Service Tub/Motor
    Assembly:
    8 To Service Motor/Clutch:
    1. Repeat
    step 4 .
    2. Loosen four
    3/8" nuts on
    bottom of
    motor. (Use
    a ratchet
    to speed
    operation.)
    3. Move motor
    towards the
    center to remove belt.
    4. Rotate transmission to give motor clearance.
    Rotate motor to the back and pull out.
    5. Proper belt tension is 1/2" deection.
    6. Reverse procedure to reassemble.
    WATER LEVEL SWITCH
    BEFORE DISCONNECTING HOSE FROM WATER
    LEVEL SWITCH, BE SURE WATER LEVEL IN
    MACHINE IS BELOWBOTTOMOF WASHBASKET.
    AFTER RECONNECTING HOSE, PUT MACHINE
    IN SPIN FOR AT LEAST ONE MINUTE BEFORE
    CHECKING OPERATION OF SWITCH.
    6 To Remove Spin Basket:
    IMPORTANT - RECONNECT ALL
    GROUNDED DEVICES
    IFGROUNDINGWIRES, SCREWS, STRAPS, CLIPS,
    NUTS ORWASHERS USEDTOCOMPLETE APATH
    TOGROUND AREREMOVEDFORSERVICE, THEY
    MUST BE RETURNEDTOTHEIR ORIGINAL POSI-
    TION AND PROPERLY FASTENED.
    IMPORTANT SAFETY NOTICE
    THIS INFORMATION IS INTENDED FOR USE BY
    INDIVIDUALS POSSESSING ADEQUATE BACK-
    GROUNDS OF ELECTRICAL, ELECTRONIC AND
    MECHANICAL EXPERIENCE. ANY ATTEMPT TO
    REPAIR A MAJOR APPLIANCE MAY RESULT IN
    PERSONAL INJURY AND PROPERTY DAMAGE.
    THE MANUFACTURER OR SELLER CANNOT BE
    RESPONSIBLE FOR THE INTERPRETATION OF
    THIS INFORMATION, NOR CAN IT ASSUME ANY
    LIABILITY IN CONNECTION WITH ITS USE.
    4. Pull to remove harness connector, and turn
    switch counterclockwise to remove from
    keyhole. Reverse procedure to reinstall.
    106-02B
    Remove Harness
    Lift Tab
    106-02E
    3 Locking Tabs
    4
    Lid Switch
    106-02F
    1
    2 4
    5
    3
    106-02H
    3. Remove front rod and spring assembly
    (one at a time) by lifting motor tub assembly
    up to take weight off suspension spring at
    lower portion of rod. Pull the spring assembly
    out of the leg and platform assembly, and
    repeat for rear rod and spring assemblies.
    Allow them to hang freely. The front and rear
    rod and spring assemblies have different
    color spring
    housings
    and should
    not be
    switched.
    106-02I
    106-02J Remove 4 Motor Nuts
    106-02P
    106-02N
    Remove
    Pulley
    Nut
    Squeeze
    Belt
    3. After pulley is removed, remove four 3/8"
    bolts mounting the transmission to leg and
    platform assembly.
    5. Remove platform.
    6. Lift transmission up and out. Transmission
    and brake are one assembly and are
    replaced as a component.
    4. Remove four 1/2" hex bolts mounting
    platform to tub.
    7. Reverse procedure to reinstall.
    TIP: Take care to align the four locating
    holes from transmission to platform before
    reinstalling transmission.
    106-02A
    106-02G
    Air Bell
    Coupler
    7/16" Bolt
    17502348G O
    106-02O
    Spin
    Basket
    106-02Q
    Split Ring
    Left
    Handed
    Thread
    Nut
    Washer
    13
    Remove 4 Screws
    106-02L
    106-02R
    Bottom of
    Basket
    Remove
    Nut
    Use Screwdriver
    To Lift Up Tab
    106-02K
    106-02S
    Align Putty Knife
    To Groove In Lid
    106-02D
    Bottom
    Slots
    Locator Tabs
    164art13.eps
    164art14.eps

    You might also like