LG R510 - SVC - Eng - 110725

1
Service Manual
Model : R510, RB510, RV510, RD510 Series
P/N :MFL57483402
REV.10
2011. 07. 25
Copy Right2011 LG Electronic inc, DigitalMate Co,.Ltd.
(LGE Internal use only)
2
Ch 1. Service information
Ch 2. Locations
Ch 3. System information
Specification
Model configuration
System Block Diagram
Fn key combinations
Status indicators
BIOS Flash
BIOS Setup
Ch 4. Symptom-to-part index
Power system checkout
Numeric error codes
Error messages
LCD-related symptoms
Indeterminate problems
Ch 5. Removing and replacing a part (FRU)
Ch 6. Part list
Part list
Exploded view
Contents
3
Chapter 1. Service information
1-1. Important service information
Strategy for replacing parts (FRU-Field Replaceable Units)
Before replacing parts
Make sure that latest BIOS and drivers are installed before replacing any parts (FRUs) listed in this
Caution
The BIOS configuration on the computer you are servicing may have been customized.
Running Automatic Configuration my alter the settings. Note the current configuration settings;
then, when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard-disk drive
You have to get a Users approval before formatting or replacing a hard-disk drive. You must let the User
know that the user is responsible for the loss data
Caution
The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an
incorrect drive, data or programs can be overwritten.
Use the following strategy to prevent unnecessary expense for replacing and servicing parts
1. If you are instructed to replacing a part but the replacement does not correct the problem, reinstall the
original part before you continue.
2. Some computers have both a processor board and system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
3. If an adapter or device consists of more than one part, anyof the parts (FRUs) may be the cause of the
error. Before replacing the adapter or device, remove the parts (FRUs), one by one, to see if the
symptoms change. Replace only the part that changed the symptoms.
Ch1. Service information
4
1-2. Safety notices
Warning
Before the computer is powered-on after part (FRU) replacement, make sure all screws, springs,
and other small parts are in place and are not left loose inside the computer. Verify this by
shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause
electrical shorts.
Warning
some standby batteries contain a small amount of nickel and cadmium. Do not disassemble
a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery
as required by local ordinances or regulations. Use only the battery in the appropriate parts
listing. Use of an incorrect battery can result in ignition or explosion of the battery
Warning
The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or
water, or short-circuit it. Dispose of the battery pack as required by local ordinances or
regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Use of an incorrect battery can result in ignition or explosion of the battery.
Warning
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands,
immediately was the affected areas with water for at least 15 minutes. Seek medical care if any
symptoms from the fluid are present after washing.
Warning
To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.
Warning
Though the main batteries have low voltage, a shorted or grounded battery can produce enough
current to burn personnel or combustible materials.
Warning
Before removing any part (FRU), turn off the computer, unplug all power cords from electrical
outlets, remove the battery pack, and then disconnect any interconnecting cables.
5
1-3. Safety information
General safety
Follow these rules to ensure general safety
Observe good housekeeping in the area of the machines during and after maintenance.
When lifting any heavy object
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles
(This action removes the strain from the muscles in your back.)
Do not attempt to lift any object weights more then 16kg(35lb) or object that you think are too heavy for you.
Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
Before you start the machine, ensure that other service representatives and the customers personnel are
not in a hazardous position.
Place removed covers and other parts in a safe place, away fromall personnel, while you are servicing the
machine.
Keep your tool box away from walk areas so that other people will not trip over it.
Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, approximately
8 centimeters(3 inches) from the end.
Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for you clothing.
Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that
is worn or defective.
Reinstall all covers correctly before returning the machine to the customer.
Caution
Metal objects are good electrical conductors.
6
Electrical safety
Observe the following rules when working on electrical equipment.
Important
Use only approved tools and test equipment. Some hand tools have handles covered with a soft
material that does not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive
fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from
electrical shock.
Find the room emergency power-off switch, disconnecting switch, or electrical outlet. If an electrical outlet.
If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly.
Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
Disconnect all power before
1. Performing a mechanical inspection
2. Working near power supplies
3. Removing or installing main units
Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine and to lock the wall box in the off position.
If you need to work on a machine that has exposed electrical circuits, observe the following precautions :
Ensure that another person, familiar with the power-off controls, is near you.
Caution
Another person must be there to switch off the power, if necessary.
Use only one hand when working with powered-on electrical equipment. Keep the other hand in your
pocket or behind your back
Caution
An electrical shock can occur only when there is a complete circuit. By observing the above rule,
you may prevent a current from through your body.
When using testers, set the controls correctly and use the approved probe leads and accessories for that
tester
7
Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal
floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages. These instructions are in
the safety sections of maintenance information. Use extreme care when measuring high voltages.
Regularly inspect and maintain your electrical hand tools for safe operational condition.
Do not use worn or broken tools and testers.
Never assume that power has been disconnected from a circuit. First check that it has been powered off.
Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
non-grounded power extension cables, power surges, and missing safety grounds.
Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive such touching can cause personal injury and machine damage.
Do not service the following parts with the power on when they are removed from their normal operating
places in a machine.
1. Power supply units
2. Pumps
3. Blowers and fans
4. Motorgenerators
and similar units. (This practice ensure correct groundingof the units.)
If an electrical accident occurs
1. Use caution ; do not become a victim of yourself.
2. Switch off power.
3. Send another person to get medical aid.
8
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions.
As each machine was designed and built, required safety items were installed to protect users and service
personnel from injury. This guide addresses only those items. You should use good judgment to identify
potential safety hazards due to attachment of non-LG features or options not covered by this inspection
guide.
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.
Consider these conditions and the safety hazards they present
1. Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
2. Mechanical hazards, such as loose or missing hardware
Refer to the following checklist and begin the checks with the power off, and the power cord disconnected.
Checklist
1. Check exterior covers for damage (loose, broken, or sharp edges)
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for :
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity
for 0.1 or less between the external ground pin and frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-LG alterations. Use good judgment as to the safety of any non-LG
alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screw or rivets) have not been removed or tampered with.
9
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between
objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Note
Use product-specific ESD procedures when they exceed the requirements noted here.
Make sure that the ESD protective devices you use have been certified (ISO9000) as fully effective.
When handling ESD-sensitive parts :
1. Keep the parts in protective packages until they are inserted into the product.
2. Wear a grounded wrist strap against your skin to eliminate static on your body.
3. Prevent the part from touching your clothing. Most clothing retains a charge even when you are wearing
a wrist strap.
4. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
5. Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.
Note
The use of a grounding system is desirable but not required to protect against ESD damage.
a. Attach the ESD ground clip too any frame ground, ground braid, or green-wire ground.
b. Use an ESD ground or reference point when working on a double-insulated or battery-operated
system. You can use coax or connector-outside shells on these systems.
c. Use the round ground-prong of the AC plug on AC-operated computers.
Grounding requirements
Electrical grounding of the computers is required for operator safety and correct system function.
Proper grounding of the electrical outlet can be verified by a certified electrician.
10
When a CD-ROM drive, DVD drive or the other laser product is installed, note the following :
Caution
Use of controls or adjustments or performance of procedures other than those specified here in
might result in hazardous radiation exposure.
1-4. Laser compliance statement
Opening the CD-ROM drive, DVD-ROM drive or the other optical storage device could result in exposure
to hazardous laser radiation.
There are no serviceable parts inside those drives. Do not open
Danger
Emits visible and invisible laser radiation when open. Do not stare into the beam , do not view
directly with optical instruments, and avoid direct exposure to the bean.
1-5. Backup (Standby) RTC battery safety information
When replacing or disposing of the backup (standby) RTC battery, note the following :
11
1-6. Read this first
Before you go to the checkout guide, be sure to read this section.
Important Notes
Only trained personnel certified by LG should service the computer.
Read the entire FRU removal and replacement page before replacing any FRU.
Use new nylon-coated screws when you replace FRUs.
Be extremely careful during such write operations as copying, saving, formatting.
Drives in the computer that you are servicing sequence might have been altered. If you selected an
incorrect drive, data or programs might be overwritten.
Replace FRUs only for the correct mode.
When you replace a FRU, make sure the model of the machine and the FRU part number are correct by
referring to the FRU parts list.
A FRU should not be replaced because of a single, irreproducible failure. Single failures can occur for a
variety of reasons that have nothing to do with a hard ware defect, such as cosmic radiation,
electrostatic discharge, or software errors.
Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective, clear the
error log and run the test again. If the error does not recur, do not replace the FRU.
Be careful not to replace a non-defective FRU.
What to do first
You must fill out the record form first.
During the warranty period, the customer may be responsible for repair costs if the computer damage was
caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. The following list provides some common items that are not covered under
warranty and some symptoms that might indicate that the systemwas subjected to stress beyond normal
use. Before checking problems with computer, determine whether the damage is covered under the
warranty by referring to the following :
12
The followings are not covered under warranty :
CD panel cracked from the application of excessive force or frombeing dropped
Scratched (cosmetic) parts
Distortion, deformation, or discoloration of the cosmetic parts
Cracked or broken plastic parts, broken latches, broken pins, or broken connectors caused by excessive
force
Damage caused by liquid spilled into system
Damage caused by improper insertion of a PC Card or the installation of an incompatible card
Damage caused foreign material in the diskette drive
Diskette drive damage caused by pressure on the diskette drive cover or by the insertion of a diskette
with multiple labels
Damaged or bent diskette eject button
Fusses blown by attachment of a non-supported device
Forgotten computer password (making the computer unusable)
Sticky keys caused by spilling a liquid onto the keyboard
The following symptoms might indicate damage caused by non-warranted activities :
Missing parts might be a symptom of unauthorized service or modification.
If the spindle of a hard-disk drive becomes noisy, it may have been subjected to excessive force, or
dropped.
13
1. VGA Port
2. Fan louvers
3. LAN Port
4. Modem Port (May vary depending on model.)
5. HDMI Port
6. e-SATA Port (USB-combo)
7. Express Card Slot
8. 6-in-1 Card Slot
(xD/SD/MMC/MMCplus/MS/MS Pro)
9. Microphone Port
10. Headphone Port
11. USB Port
12. USB Port
13. Optical Disk Drive
14. Power Port
15. Kensington lock
Chapter 2. Locations
Ch2. Locations
Left View
Right View
14
Ch2. Locations
16. Fan louvers

Rear View
17. Built-in Microphone
(May vary depending on
model.)
18. LG Smart Cam
(May vary depending on
model.)
19. Power Button
20. Keyboard
21. Touchpad
22. Stereo speaker
Front View
15
Chapter 3. System information
Specification
Ch3. System information
- Processors
Intel Core2 Duo/Solo/Mobile Intel Celeron Processor(L2 Cache Size: 1MB/2MB/4MB/6MB/8MB,
FSB:533/800MHZ are supported.)
The user must not replace or expand the CPU capacity arbitrarily. The CPU capacity differs depends on
model type.
- Main Memory
Maximum Capacity: Each slot is 2048MB and can be expanded to 4096MB.
SO DIMM Type for Memory Expansion: DDR2/DDR3 SDRAM SO-DIMM(256MB, 512MB, 1024MB,
2048MB)
Memory types and specifications may differ by model type.
To use two 2GB memory cards, the machine must run on 64bit OS. 32bit Vista/XP OS does not support
4GB memory.
- Secondary Storage
2.5" Hard Disk Drive (S-ATA)
The hard disk capacity and the type depend on the notebook PC model.
Optical Disk Drive
The specifications may differ by model type.
- LCD
15.4" WXGA (1280 x 800) TFT Color LCD
15.4" WXGA LED (1280 x 800) TFT Color LCD
15.4" WXGA+LED (1440 x 900) TFT Color LCD
Some models are equipped with Glare Type LCD. This model is enhanced the sharpness compare to the
other types of LCD. So, it may appears glaring a lot but this is the normal status.
The size and the resolution rate of the LCD depend on the notebook PC model.
- Authentication for Anticopy Technology
U.S Patent Nos.4,631,603;4,577,216;4,819,908;4,907,093;5,315,448;and 6,516,132. Patent number of
Macrovision.
This product includes the technologies that are possessed by Macrovision and corresponding companies
and protected by the US Patent Law and other related laws. Use of all technologies subject to the copyrig
ts must be approved by Macrovision in advance. Otherwise, the technologies may only be used for intern
al display. Do not disassemble or remodel the product.
- Bluetooth
Qcom, QBTM300 / LGIT RBDS-C001X
Ver2.0 Bluetooth Module
Bluetooth is optional, and so it may not be installed in some models.
- Web Camera
1.3 Mega pixels USB camera module
UVC(USB Video Class) driver support
Web Camera is optional, and so it may not be installed in some models
16
Specification
- External I/O Interface
Microphone Input Port (Mic in): 1
Headphone Port: 1
HDMI Port: 1
e-SATA (USB Combo) Port: 1
USB 2.0 Ports: 2
Multi-card Slot: 1
Express Card Slot: 1
RJ 11 (Modem) Port: 1
USB 2.0 Ports: 4
The support availability may differ by model type.
RJ 45 (LAN) Port: 1
- Video
Mobile Intel Graphic Media Accelerator 4500MHD (Dynamic Video Memory Technology)
The DVMT actively utilizes part of the system memory when processing large graphic data like 3D graphics.
Therefore, the size of the graphic memory is displayed as the sum of the actual graphic memory size and
the utilized amount of memory, which is decided by the size of system memory.
NVIDIA Geforce 9600M GT (W/GDDR3 256M ) with TurboCache 320MB~1535MB
NVIDIA Geforce 9600M GT (W/GDDR3 512M) with TurboCache 576MB~1791MB
NVIDIA Geforce 9300M GS (W/GDDR3 256M) with TurboCache 320MB~1535MB
TurboCache - This technology actively utilizes part of the System Memory when processing large graphic
data like 3D graphics. The size of the utilized memory is determined by the Video Memory size and System
Memory Size.
If TurboCache technology is applied to the Graphics Memory, the System Memory can allot up to 320MB
out of 512MB and up to 1791MB out of 4096MB for large graphic data.
Specifications may differ by model type.
- Sound
Realtek High Definition Audio Codec (ALC262) HDMI is supported
Built-in Stereo Speakers
- MODEM
AGERE Delphi D40
RJ 11 J ack
The support availability may differ by model type.
- LAN
Intel 82657LM/LF PCI Express Fast Ethernet Controller
RJ 45 J ack
Specifications may differ by model type.
- Wireless LAN
Intel 512AG_MMW / 512AN_MMW / 533AN_MMW
Ralink RT2700E
Wireless LAN specifications may differ by model type and cannot be arbitrarily changed by the user.
- Weight
Full Installation: About 2.7kg (2.5kg when using Weight Saver)
Battery: About 320g
Weight descriptions may differ by model type.
17
System Block Diagram
11
22
33
44
55
66
77
88
A
A
B
B
C
C
D
D
v
e
R
r
e
b
m
u
N

t
n
e
m
u
c
o
D
e
zi
S
t
e
e
h
S
:
e
t
a
D
o
f
Q
u
a
n
t
a

C
o
m
p
u
t
e
r

I
n
c
.
P
R
O
J
E
C
T

:

Q
L
8
N
B
5
B
l
o
c
k

D
i
a
g
r
a
m
3
A
C
u
s
t
o
m
1
4
1
M
o
n
d
a
y
,

M
a
y

1
2
,

2
0
0
8
v
e
R
r
e
b
m
u
N

t
n
e
m
u
c
o
D
e
zi
S
t
e
e
h
S
:
e
t
a
D
o
f
Q
u
a
n
t
a

C
o
m
p
u
t
e
r

I
n
c
.
P
R
O
J
E
C
T

:

Q
L
8
N
B
5
B
l
o
c
k

D
i
a
g
r
a
m
3
A
C
u
s
t
o
m
1
4
1
M
o
n
d
a
y
,

M
a
y

1
2
,

2
0
0
8
v
e
R
r
e
b
m
u
N

t
n
e
m
u
c
o
D
e
zi
S
t
e
e
h
S
:
e
t
a
D
o
f
Q
u
a
n
t
a

C
o
m
p
u
t
e
r

I
n
c
.
P
R
O
J
E
C
T

:

Q
L
8
N
B
5
B
l
o
c
k

D
i
a
g
r
a
m
3
A
C
u
s
t
o
m
1
4
1
M
o
n
d
a
y
,

M
a
y

1
2
,

2
0
0
8
Q
L
8
/
T
W
8
(
1
5
.
4
W
)

B
L
O
C
K

D
I
A
G
R
A
M
P
C
B

S
T
A
C
K

U
P
0
1
P
A
G
E

4
0
M
i
n
i

P
C
I
-
E
C
a
r
d
1
,
2
9
8
R
T
L
8
1
0
2
E
/
8
1
1
1
C
E
x
p
r
e
s
s
C
a
r
d
(
N
E
W

C
A
R
D
)
K
e
y
b
o
a
r
d
L
C
D

C
O
N
N
E
-
S
A
T
A
B
l
u
e
T
o
o
t
h
U
S
B
2
.
0

P
o
r
t
s
T
o
u
c
h

P
a
d
A
U
D
I
O
A
m
p
l
i
f
i
e
r
T
P
A
6
0
1
7
A
2
A
n
a
l
o
g
L
P
C
E
N
E

K
B
C
P
A
G
E

3
4
P
A
G
E

3
4
S
A
T
A

-

C
D
-
R
O
M
F
A
N
A
z
a
l
i
a
R
e
a
l
t
e
k
P
C
I
E
-
L
A
N
L
A
N
X
2
W
e
b
c
a
m
H
D
M
I

C
O
N
D
o
c
k
i
n
g
C
R
T
L
A
N
/
R
J
-
4
5
U
S
B

P
o
r
t
S
A
T
A
5

1
5
0
M
B
P
A
G
E

3
9
V
C
C
P

+
1
.
5
V

A
N
D

G
M
C
H
1
.
0
5
V
(
R
T
8
2
0
4
)
P
A
G
E

2
5
P
A
G
E

3
6
P
A
G
E

3
8
P
A
G
E

3
5
C
P
U
P
e
n
r
y
n
4
7
8
P

(
u
P
G
A
)
/
3
5
W
N
O
R
T
H

B
R
I
D
G
E
C
a
n
t
i
g
a
I
C
H
9
-
M
S
O
U
T
H

B
R
I
D
G
E
P
C
I
-
E
(
1
0
/
1
0
0
/
G
a
g
a
L
A
N
)
A
L
P
R
S
3
5
5
B

M
L
F
6
4
P
I
N
P
A
G
E

2
6
P
A
G
E

1
9
S
Y
S
T
E
M

P
O
W
E
R

I
S
L
6
2
3
7
I
R
Z
-
T
V
G
A
C
O
R
E
(
1
.
0
2
5
V
)
O
z
8
1
1
8
C
P
U

C
O
R
E

I
S
L
6
2
6
6
A
S
Y
S
T
E
M

C
H
A
R
G
E
R
(
I
S
L
6
2
5
1
A
H
A
Z
-
T
)
P
A
G
E

3
2
S
P
I
P
A
G
E

3
2
A
z
a
l
i
a

A
L
C
2
6
8
X
2
X
1
X
1
J
a
c
k

t
o
S
p
e
a
k
e
r
P
A
G
E

2
7
P
A
G
E

2
7
M
D
C

C
O
N
N
P
C
I
-
E
x
p
r
e
s
s
3
2
.
7
6
8
K
H
z
R
J
4
5
P
A
G
E

2
8
2
5
M
H
z
3
2
.
7
6
8
K
H
z
D
D
R

I
I

S
M
D
D
R
_
V
T
E
R
M
1
.
8
V
/
1
.
8
V
S
U
S
(
T
P
S
5
1
1
1
6
R
E
G
R
)
R
T
S
5
1
5
8
E
6
P
A
G
E

1
9
1
4
.
3
1
8
M
H
z
C
L
O
C
K

G
E
N
C
P
U

T
H
E
R
M
A
L
S
E
N
S
O
R
D
D
R
I
I
-
S
O
D
I
M
M
2
D
D
R
I
I
-
S
O
D
I
M
M
1
D
D
R
I
I

6
6
7
/
8
0
0

M
H
z
D
D
R
I
I

6
6
7
/
8
0
0

M
H
z
C
L
K
_
C
P
U
_
B
C
L
K
,
C
L
K
_
C
P
U
_
B
C
L
K
#
C
L
K
_
M
C
H
_
B
C
L
K
,
C
L
K
_
M
C
H
_
B
C
L
K
#
D
R
E
F
C
L
K
,
D
R
E
F
C
L
K
#
D
R
E
F
S
S
C
L
K
,
D
R
E
F
S
S
C
L
K
#
N
B
S
R
C
C
L
K
,

N
B
S
R
C
C
L
K
#
P
S
8
1
0
1
P
A
G
E

2
0
D
M
I

L
I
N
K
A
u
d
i
o

J
a
c
k
s

m
i
c
r
o
p
h
o
n
e
(
P
h
o
n
e
/

M
I
C
)
P
A
G
E

3
,
4
P
A
G
E

5
P
A
G
E

5
~
9
P
A
G
E

1
0
P
A
G
E

1
0
P
A
G
E

2
P
A
G
E

1
2
~
1
8
P
A
G
E

2
0
P
A
G
E

1
9
P
A
G
E

2
1
,
2
2
,
2
3
,
2
4
P
A
G
E

2
6
P
A
G
E

2
7
P
A
G
E

3
0
P
A
G
E

3
1
P
A
G
E

2
6
P
A
G
E

3
3
P
A
G
E

2
8
,
2
9
P
A
G
E

3
0
P
A
G
E

2
0
C
R
T
P
A
G
E

2
6
P
A
G
E

3
0P
A
G
E

3
2 S
A
T
A
0

1
5
0
M
B
9
6
9
p
P
A
G
E

3
7
N
V
I
D
I
A

N
B
9
M
-
G
S
6
4
b
i
t

o
r
N
B
9
P
-
G
E
2

1
2
8
b
i
t
2
7
M
H
z
1
2
M
H
z
D
u
a
l

L
i
n
k
S
A
T
A

-

H
D
D
S
A
T
A
1

1
5
0
M
B
U
S
B
2
.
0
H
e
a
d
p
h
o
n
e

J
a
c
k
F
S
B

6
6
7
/
8
0
0
/
1
0
6
6
K
B
3
9
2
6

C
0
G
9
9
5
P
A
G
E

2
2
S
P
I
8
L
L
A
Y
E
R

2

:

S
G
N
D
L
A
Y
E
R

5

:

S
V
C
C
L
A
Y
E
R

1

:

T
O
P
L
A
Y
E
R

8

:

B
O
T
L
A
Y
E
R

3

:

I
N
1
L
A
Y
E
R

6

:

I
N
2
1
6
X
(
W
i
r
e
l
e
s
s
L
A
N
/
W
W
A
N
)
7
E
-
S
A
T
A

x
1
0
D
o
c
k
i
n
g

x
1
E
x
p
r
e
s
s

C
a
r
d

x
1
M
i
n
i

P
C
I
-
E
(
W
W
A
N
)
1
1
4
L
A
Y
E
R

7

:

S
G
N
D
2
L
A
Y
E
R

4

:

S
G
N
D
1
M
i
n
i

P
C
I
-
E
(
W
L
A
N
)
1
0
F
O
R

T
W
8
18
Fn key combinations
The following table shows the function of each combination of Fnwith a function key.
Function of Fn keys has nothing to do with Operating System.
Fan Control feature. Switches the cooling fan mode between Normal and Silent for each pressing. Fn + F11
Hibernates (When OSD is installed) Fn + F12
System Information. Displays summarized system information. Fn + F10
Turns the numeric keypad on and off.
Deletekey types when Num Lock is enabled, and work as a "Delete" key when Num Lock is
disabled.
Fn + NumLk
Increases LCD brightness within a nine-grade range. Fn +
Decreases LCD brightness within a nine-grade range. Fn +
Turns down the volume. Fn +
Turns up the volume. Fn +
Mute (Sound ON / Sound OFF) Fn + F9
Switches between SRS WOW HD, SRS TruSurround XT, and SRS Off for each pressing. Fn + F8
Monitor toggle. If you have an external monitor connected to the computer, press Fn + F7 keys to
rotate the display mode between LCD only, Monitor only, and LCD + Monitor both in order.
Fn + F7
Turns the wireless devices (incl. Wireless LAN and Bluetooth) on and off (Bluetooth is optional, and
so it may not be installed in some models.)
Through hot key settings in the OSD Tray menu, the user can customize [Fn]+[F6] features. Default
setting is, for all wireless devices (incl. Wireless LAN and Bluetooth), ON/Off.
Fn + F6
When the user presses Fn +F5 keys, the touchpad mode alternates between Touchpad Disable,
Touchpad Auto-Disable (upon connection of external USB mouse), and Touchpad Enable in order.
(Initialization takes 1 ~2 seconds. It is recommended to use after the initialization.)
Fn + F5
Executes the mode defined in the Windows Power Save Mode. (Example: Standby, Hibernate) Fn + F4
Magnifying hot keys. Fn + F3
Customizable hot keys. (Configurable through OSD settings) Fn + F2
Customizable hot keys. (Configurable through OSD settings) Fn + F1
19
The system status indicators show the status of the computer
1 . Power Lamp:
Blinking: System Standby
On: The system is running on the AC power or battery.
Off: The system is turned off or in Hibernates.
2. AC Power and Battery Status Lamp
Orange: The battery is being charged.
Orange/Green Blinking: Charged more than 90%
Off: The AC adapter is not connected and the battery is being discharged.
Green: The AC adapter is connected and the battery is not in charging stage, or the battery is fully
charged.
Green Blinking: The battery is charged less than 10%
Red Blinking: In faulty state
If you try to turn on the system that has entered the Hibernates mode or been turned off after a low-battery
alarm, the system will not be turned on but the lamp will blink three times.
3. Hard Disk Drive Lamp
The lamp is turned on when the HDD is running.
Do not turn off the power forcibly while the hard disk drive lamp is on. Otherwise, the data may get
impaired.
4. Num Lock lamp
You can activate Num Lock feature by pressing the Num Lk key. Then, the NumLock lamp will be turned
on and you can input numbers (0 ~9) using the numeric keypad. Press the Num Lk key again to turn off
the feature and use the keys as the lowercase signs including arrows indicate.
5. Caps Lock lamp
Caps Lock lamp is on when the it is active. When this lamp is on, you can type uppercase letters without
holding Shift key.
Status indicators
20
6 . Wireless LAN/Bluetooth lamp
Off: Wireless LAN/Bluetooth is not in use.
Blinking (short interval): Wireless LAN/Bluetooth is connected and data are being transmitted.
Blinking (every 2 ~3 seconds): Wireless LAN/Bluetooth is not connected but Wireless Radio is on.
Blinking (every 3 ~4 seconds): An access Point is being searched for to connect Wireless LAN/Bluetooth.
On: An access point is being searched for or Wireless LAN/Bluetooth is connected.
The Wireless LAN/Bluetooth lamp may operate differently depending on model type.
The Wireless LAN card and the Bluetooth device are optional, and so it may not be supported in some
models.
21
BIOS Flash
You Can update BIOS using USB Device (FDD/USB Memory)
Because this system is not equipped with any USB Device, you have to use an external USB Device
for a BIOS update.
In order to boot up with an USB Device, please set Removable Device as the
first boot up drive in the boot menu of BIOS Setup.
How to update flash Rom in Dos
1. Create boot up flash update USB Device (FDD/USB Memory).
2. Copy BIOS Flash software to the flash update USB Device (FDD/USB Memory).
3. Connect the USB Device for USB Port.
4. Press F12 Key while the "LG LOGO" appears.
5. A while later, the system setup home screen appears.
6. Type in go.bat . (x_xxx is Model Name & BIOS version)
7. You can see the BIOS flash process as below.
8. After flashing is completed, The computer turn off with automatic movement. .
22
10. Press [F2] Key, then you can see the BIOS SETUP UTILITY screen as below.
11. It selects the :Load Optimal Dafaultand it summons a BIOS settings at initial value.
23
12. It selects the Exit & Saving Changeand it stores system a settings and the reboot
24
BIOS Release Process and Making Bootable CD
1. LGE(Korea) will upload BIOS Image(*.iso) to GCSC(Global Cyber Service Center:http://biz.lgservice.com)
when BIOS should be updated.
2. BIOS will include both System BIOS and EC(EmbeddedController) BIOS.
3. Service center can download BIOS file from GCSC and update BIOS according to below procedure.
4. Service center will make Bootable Image CD with Image file(*.iso) as below
a. Insert empty disc to CD-RW Drive and start Nero StartSmart.
b. Select Nero Express.
25
c. Select Disc Image or Saved Project
d. Select File Format as "Image Files(*.iso)".
26
e. Open Image File(*.iso) which is sent from LGE
f. Tab Burn then burning will be started
27
g. Burn process completed as below, and tab OK
28
BIOS/EC Flash Process
1. Insert Bootable CD in PC, and Turn it on, then PC will boot by DOS mode as below
(If the EC is not correct or old version, then automatically update EC first and reboot again)
2. Select Boot mode, then press EnterKey.
3. Type in LOGO SETTING at the WIP ID :then press Enter key (You must use Capital Letter)
29
4. Type in Mode Name at the WIP ID :then press Enter key (You must use Capital Letter)
(You can see the Model Name in ID Label at the bottom Case of PC: M/N: LMXX-XXXX)
5. Type in Serial No at the WIP ID :then press Enter key (You must use Capital Letter)
(You can see the Serial No in ID Label at the bottom Case of PC: S/N: 412KIXXXXXXXX(13digits))
6. You can see the BIOS flash process as below
30
5. After flashing is completed, you can see the PASSon your screen, and reboot your PC
31
BIOS Setup
BIOS (Basic Input and Output System) Setup saves the system configuration in CMOS RAM, and
check the configurations during startup. Use the BIOS Setup Utility to change and save the system
environment, hardware configurations, power saving mode, etc.
Open the BIOS Setup Utility in the following situations :
1. to change the BIOS setup
2. to replace the backup battery
3. system configuration error occurs
4. to change the boot order
5. to set/change a password
Press the power button.
When the LG logo appears on the screen, press and enter the BIOS Setup Utility.
32
Using the keys
The keys used in the BIOS Setup Utility and their functions are described at the bottom.
, + : General Help
Display the descriptions of the keys used in the setup utility.
, : Select Item
Navigate and select items in the setup utility. The selected item becomes highlighted.
, : Select Menu
Move to another menu.
/ , : Change Values
Change the value of a selected item.
: Load Default Configuration
Display Setup Confirmation window. Press Enter to load default configuration.
: Select Sub-Menu
Some items have sub-menus. Display the sub-menu for a selected item.
: Save and Exit
Display Setup Confirmation window. Press Enter to save and exit.
: Exit
In a sub-menu, press Esc to move to the previous window. In Main menu, click Esc to move to Exit menu.
33
System Time
Current time. To change the value, press <+>or <>key.
System Date
Current date. To change the value, press <+>or <>key.
SATA Hard Dri ve
This shows the description of the drive connected to the SATA port.
To change the settings of the connected drive, click <Enter> after selecting this option.
CD-ROM/DVD-ROM
This shows the description of the drive connected to the ODD drive port.
To change the settings of the connected drive, click <Enter> after selecting this option.
Main menu
34
Advanced menu
USB BIOS Legacy Support
This enables to use the USB devices in the MS-DOS environment.
HDC Configure as
This configures the compatibility settings for the SATA controller.
VT Support
Set whether or not to support the Intel virtualization technology.
AC Mode Fan always on
Select any of Normal, Silent, and Cool for the operating speed of CPU cooling fan (for AC power).
DC Mode Fan always on
Select any of Normal, Silent, and Cool for the operating speed of CPU cooling fan (for DC power).
Mute button option
Set whether or not to support the Mute function (Fn +F9) during the system startup.
Internal Devices Configurations
Set whether or not to use the devices such as Auiod, LAN, Wireless, Card reader, Express carder, and
such.
35
Security menu
Supervisor Password
The password setting prevents not allowed users from using the notebook computer. The password is not
set when starting the system for the first time. When the systemis turned on, any other user cannot
change the BIOS settings without entering the specified password.
User Password
Set User Password is for setting the password lower than the one set in Set Supervisor Password. Set
User Password is active only when the supervisor password is set.
Set Supervisor Password
Set Supervisor Password.
Set User Password
Set User Password.
Set All Hdd Password
Set the HDD password.
36
Boot menu
Quick Boot
Set whether or not to use Quiet Boot.
PXE Boot to LAN
Set whether or not to use the HDD password.
Boot Device Priority
Select the desired device drive by using the arrow buttons and change its booting sequence by using the
[+] or [-] key.
37
Info menu
BIOS Version
This shows the Version of BIOS.
KBC Version
This shows the Version of KBD firm ware.
Serial Number
This shows the serial number of the product.
CPU Type
This shows the type of the CPU installed in the system.
L2 Cache RAM
This shows the size of L2 Cache RAM for the CPU.
Total Memory
This is for display only. This shows size of system memory.
Slot 13 Memory
This shows the size of the memory installed in the memory slot.
38
Exit menu
Exit & Save Change
Save the changes you have made and exit the utility.
Exit & Discard Changes
Exit the utility without saving the changes you have made.
Load Optimal Defaults
This changes the parameters in the Setup menu to the factory default settings. When it is selected or [F9]
key is pressed, the confirmation message appears. Click [Yes] to change the settings.
Load Custom Defaults
This returns the user-defined settings for the parameters in the Setup menu.
Save Custom Defaults
This saves the desired values for each parameter in the Setup menu.
Discard Changes
This returns to the factory default settings for each parameter in the Setup menu.
39
Backup and Restore Security Platform Data
Security Platform Backup includes all data required in case of emergency. After a hardware or storage
media failure or a Trusted Platform Module failure, Security Platform Restoration reestablishes access to
Security Platform Features for all users.
In addition you can backup and restore your Personal Secure Drive data. Data from other applications
using the Security Platform Solution (e.g. Secure e-mail) is not included in Security Platform backup.
Backup scope
Security Platform backup comprises the following data:
Emergency Recovery data is included in automatically written
Backup Archives.
Emergency Recovery Token (e.g.
SPEmRecToken. xml
): Created by
Security Platform Administrator. Protected with a dedicated password.
Is required for a restoration of Emergency Recovery data.
Archives
Re-encryption of all Basic User Keys after a Trusted Platform Module failure.
In this case a new Security Platform has to be set up and a new owner
key is created. Emergency Recovery allows the re-encryption of Basic
User Keys from the old owner key to the new one.
Otherwise users could not access Security Platform Features anymore
and user data would be lost.
Purpose
All Security Platform Basic User Keys, encrypted specifically for Emergency
Recovery.
Backup Contents
Emergency Recovery
Automatically written Backup Archive ("System Backup Archive",
e.g. file
SPSyst emBackup. xml
and folder
SPSyst emBackup
): Set up by
Security Platform Administrator. Contains credentials and settings of all
Security Platform Users (for one or multiple Security Platform
computers). Also contains computer identification and user
identification, which are used to match computers and users during the
restoration process.
Manually written Backup Archive (e.g.
SPBackupAr chi ve. xml
):
Created by Security Platform User. Contains credentials and settings of
one Security Platform User (for one Security Platform computer). Also
contains computer identification and user identification, which are used
to match computer and user during the restoration process.
Archives
Restoration of user-specific credentials and settings after a hardware or
storage media failure.
Otherwise users could not access Security Platform Features anymore
and user data would be lost.
Purpose
A copy of the user-specific credentials and settings which are stored on the
Security Platform.
Backup Contents
Security Platform Credentials and Settings
40
PSD configuration settings are included in both automatically
written Backup Archives and manually written Backup Archives.
PSD backup file (e.g.
SpPSDBackup. f sb
): A backup copy of the PSD
image file may be created during a Security Platform User's manual
backup.
Archives
Restoration of PSD encrypted data and configuration settings after a
hardware or storage media failure.
Otherwise users could not decrypt their PSD data anymore.
Notes:
In contrast to the PSD Backup, standard hard disk backup tools
produce unencrypted backups.
Lost PSD credentials can only be restored via Personal Secure Drive
Recovery.
Purpose
A copy of the PSD encrypted data and configuration settings. Backup Contents
Personal Secure Drive
Restoration Cases
Depending on the type of emergency there are different restoration cases
Emergency Recovery, Security Platform Credentials
and Settings, Personal Secure Drive
New Security Platform to be initialized
Emergency Recovery New Trusted Platform Module
Security Platform Credentials and Settings, Personal
Secure Drive
Broken hard disk or lost data
Affected Restoration Scope Restoration Case
41
How to Backup and Restore
Settings Tool - Backup - Restore... Administrative Task: Prepare restoration for
certain users.
User Task: Run restoration manually for
current user. If restoration has been
prepared for current user, then complete the
restoration.
If a manually written Backup Archive is
available and no Emergency Recovery data
needs to be restored, then a user can
perform restoration without preparation by
an administrator.
Software Component to use How to restore
Settings Tool - Backup - Backup... User Task: Run backup manually for the
current user.
Software Component to use How to backup ("Manual Backup")
If Security Platform is not yet initialized:
Initialization Wizard
If Security Platform is already initialized: Settings
Tool - Backup - Configure...
Administrative Task: Configure automatic
backups for all users (including Security
Platform Credentials and Settings,
Emergency Recovery and PSD configuration
settings).
Software Component to use How to configure automatic backups
("System Backup")
Backup
With this page you can configure automatic Security Platform backups.
The following table gives hints on how to use this wizard page.
A scheduled backup will be created.
Click here to view and modify the backup scheduling.
Please note that automatic backups are only executed if your PC is not
shut down at the scheduled time.
Please note that the user account chosen for the scheduled backup must
be member of the group "Administrators" or "Backup Operators".
Schedule...
Security Platform credentials and settings will be regularly saved to a
Backup Archive.
Type in path and file name or browse for it. An automatically written
Backup Archive consisting of an XML file and a folder with the same name
will be created, e.g. file
SPSyst emBackup. xml
and folder
SPSyst emBackup
.
Please use the extension *.xml.
Backup location:
Browse...
Explanation Wizard Page Element
42
Infineon Platform Security Backup
With this page you can backup and restore Security Platform credentials, Security Platform settings and
Personal Secure Drives.
If Enhanced Authentication is enabled, you can also create backups of your authentication device.
Availability of page: This page is only available on an initialized Security Platform, if one of
the following conditions is fulfilled:
The current user has administrative rights.
The current user is an initialized Security Platform User, and the policy Allow User Enrollment
is enabled.
Buttons:
Buttons for administrative tasks are disabled for users without administrative rights.
Buttons are disabled, if corresponding functions are not available in a certain Security Platform
state.
The following table describes all backup and restore functions.
Click here to create a backup authentication device.
This feature is only available, if Enhanced Authentication is enabled.
Click here to start a manual restore of archived Security Platform Settings and credentials. If you
have a backup of your Personal Secure Drive (PSD), you can restore your PSD too.
The restore part of the Infineon Security Platform Backup Wizard will be started.
This button is disabled, if the Infineon Security Platform is disabled or not yet set up.
Click here to start a manual backup of your Security Platform Settings and credentials. If you have
configured Personal Secure Drive (PSD), you can backup your PSD too.
The Infineon Security Platform Backup Wizard will be started.
This button is disabled, if the Infineon Security Platform is disabled, not yet set up or the user is not
set up.
Click here to set up automatic Security Platform backups.
Infineon Security Platform Initialization Wizard will be started.
This feature is only available, if the current user account has administrative rights.
Explanation
43
Note
If replacing a part (FRU) does not solve the problem, put the original part back in the computer.
Do not replace a non-defective FRU.
The symptom-to-part index in this section lists symptoms and errors and their possible causes.
The most likely cause is listed first.
Power system checkout
To verify a symptom, do the following :
1. Power off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Check that power is supplied when you power on the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you power on the computer.
If you suspect a power problem, see the appropriate one of the following power supply checkouts :
1. Checking the AC adapter
2. Checking the operational charging
3. Checking the battery pack
4. Checking the backup battery
Checking the AC adapter
If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity
and installation.
If the computer does not charge during operation, go to Checking operational charging.
Chapter 4. Symptom-to-part index
Ch4. Symptom-to-part index
44
To check the AC adapter, do the following :
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the
AC adapter cable. See the following figure :
3. If the voltage is not correct, remove the power code
form AC adapter.
4. 10 seconds later, connect the power code, then measure the output voltage.
5. If the voltage is not correct, change the AC adapter.
2
1
Ground 2
+18.05 ~+19.95 1
Voltage (V dc) Pin
45
If the voltage is not correct, replace the AC adapter.
If the voltage is acceptable, do the following :
1. Replace the system board.
2. If the problem persists, check the AC adapter whether it is correct product or not.
Checking operational charging
1. To check whether the battery charges properly during operation, use a discharged battery pack or a
battery pack that has less than 50% of the total power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
does not turn on, replace the battery pack.
2. If the charge indicator still does not turn on, replace the system board.
Then reinstall the battery pack.
Note
Noise from the AC adapter does not always indicate a defect.
Note
Do not charge battery pack, when its temperature is below 0 or above 75 .
Checking the battery pack
1. Open the Power Meter window by clicking Start Control Panel Power Options and then;
check the total power remains. Battery charging does not start until the power Meter shows that less
than 95% of the total power remains; under this condition the battery pack can charge to 100% of its
capacity. This protects the battery pack from being overcharged or from having a shortened life.
2. To check the status of your batter, move your cursor to the Power Meter icon in the icon tray of the
Windows taskbar and wait for a moment (but do not click), and the percentage of battery power
remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon.
Note
If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and
Leave it at room temperature for a while. After it cools down, reinstall and recharge it.
46
The Characteristics of the battery pack
1. Self-discharge
The battery gradually loses its power over time without ever being used.
2. Periodic full discharge / charge
Frequent recharge of the battery pack can reduce the capacity of the battery pack. When this happens,
you can perform the full discharge / charge to improve the capacity. You should perform periodic full
discharge /charge once every 30~60 days.
You should always use the battery until its power is low; then fully charge the battery.
3. Trickle charge
If the temperature of the battery pack drops below 10 , the trickle charging begins.
The trickle charging may take 32 hours for the battery pack to be fully charged.
47
To check the battery pack, do the following :
2. Remove the battery pack and measure the voltage between battery terminals 1(-) and 5(+).
See the following figure :
+0V ~+12.6V
(6 cell)
5
Ground(-) 1
Voltage (V dc) Terminal
Note
Charging will take at least 3 hours.
3. If the voltage is still less than +11.1 V DC after recharging, replace the battery.
4. If the voltage is more than +11.1 V DC, measure the resistance between battery terminals 1 and 2.
The resistance must be 2 to 4 (typically 3 ).
5. If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system
board.
Note
Battery is an expendable supplier, so its capacity and used time can be reduced by using the computer.
5(+) 4 3 2 1(-)
48
Numeric error codes
Replace the backup battery and run BIOS Setup
Utility
to reset the time and date.
0250
System battery error System battery is dead
1. DIMM
2. System board
0232
Extended RAM error - Extended RAM Failed
at address line
System board 0231
Shadow RAM error - Shadow RAM failed at
offset
1.DIMM
2.System board
0230
System RAM error - System RAM Failed at
offset.
Load Setup Defaults in BIOS Setup Utility. 0220
Monitor type error - Monitor type does not
match the one specified in CMOS.
System board. 0212
Keyboard Controller Failed
Run interactive tests of the keyboard and the auxiliary
input device.
0211
Keyboard error
1.Check the keyboard if it is pressed.
2.Replace the keyboard.
0210
Stuck Key error
1.Reset the hard-disk drive.
2.Load Setup Defaults in BIOS Setup Utility.
3.Hard-disk drive.
4.System board.
0200
Fixed disk failure
(The hard disk is not working)
FRU or action, in sequence Symptom / Error
49
1. DIMM
2. System board
02F6
Software NMI failed
1. DIMM
2. System board
02F5
DMA test failed
1. Load Setup Defaultin BIOS Setup Utility.
2. Replace the backup battery.
3. System board.
02F4
EISA CMOS not writable
2. System board.
02D0
System cache error Cache disabled
(RAM cache failed and BIOS disabled)
1. Floppy diskette drive.
2. External FDD cable.
3. I/O card.
02B3
Incorrect Drive B type
1. Floppy diskette drive.
2. External FDD cable.
3. I/O card.
02B2
Incorrect drive A type Floppy diskette drive
error
Set up the diskette type in BIOS Setup Utility. 02B1
Diskette drive B error
Set up the diskette type in BIOS Setup Utility. 02B0
Diskette drive A error
Load Setup Defaults in BIOS Setup Utility. 0281: Memory Size found by POST differed
from EISA CMOS
2. DIMM.
3. System board.
0280
Previous boot incomplete
- Default configuration used
Run BIOS Setup Utility to reset the time and date. 0271
Check date and time settings Date and time
error.
1. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
2. System board.
0260
System timer error
Reset the password by running BIOS Setup Utility. 0252
Password checksum bad The password is
cleared.
Replace the backup battery and run BIOS Setup
Utility
to reset the time and date.
0251
System CMOS checksum bad
System CMOS checksum is not correct.
Default configuration used.
50
1. Load Setup Defaults in BIOS Setup Utility.
2. System board.
061A
Parallel port configuration error
2. System board.
0619
Parallel port configuration changed
2. System board.
0618
Floppy configuration error
2. System board.
0617
Floppy configuration changed
2. System board.
0616
Com B configuration error
2. System board.
0615
Com B configuration changed
2. System board.
0614
Com A configuration error
2. System board.
0613
Com A configuration changed
2. System board.
0612
IDE configuration error
2. System board.
0611
IDE configuration changed
1. DIMM
2. System board
02F7
Fail Safe timer NMI failed
51
System board. Thermal sensing error.
Fan. FAN error.
1. Restore the system configuration to what it was
before the computer entered hibernation mode.
2. If memory size has been changed, re-create the
hibernation file.
Hibernation error.
1. Check that the operating system has no failure and
is installed correctly.
2. Enter BIOS Setup Utility and see whether the hard
-disk drive and the diskette drive are properly
identified.
3. Reset the hard-disk drive.
4. Reinstall the operating system.
5. Diskette drive.
6. Hard-disk drive.
7. System board.
Operating System not found.
2. Backup battery.
3. System board.
I/O Device IRQ Conflict.
1. DIMM.
2. System board.
Invalid System Configuration Data.
1. DIMM.
2. System board.
Failing bits: nnnn.
2. Backup battery.
3. System board.
Allocation error for device.
2. Backup battery.
3. System board.
Device address conflict.
Error message
52
LCD-related symptoms
Note
Before removing or disassembling LCD, power off the computer, unplug all power cords from electrical
outlets, remove the battery pack also.
LCD Assembly.
System board.
Power-on indicator on, and a blank\LCD
during POST.
LCD Assembly. Horizontal or vertical lines displayed
on LCD
1. Reset all LCD connectors.
2. Replace LCD cable.
3. LCD Assembly.
4. System board.
LCD color cannot be adjusted.
LCD screen abnormal.
Characters missing pixels.
LCD screen unreadable.
Wrong color displayed.
1. Reconnect inverter to the board connector.
2. Replace inverter.
3. LCD Assembly.
4. System board.
LCD backlight not working.
LCD too dark.
LCD brightness cannot be adjusted.
1. Check out Battery Miser.
2. Choose Never in the Turn off Monitor item on
Power Options Properties.
3. Check the power save mode switch if it is pressed
by something.
4. Check the System is in standby or hibernation
mode.
Nothing displayed on LCD screen.
Check out Battery Miser. LCD screen becomes dark suddenly.
53
Indeterminate problems
You are here because the diagnostic tests did not identify which adapter or device failed, wrong devices
are installed, a short circuit is suspected, or the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating correctly.
1. Power off the computer
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnected all of the following devices :
a. Non-LG devices.
b. Printer, mouse, and other external devices.
c. Battery pack.
d. PC cards.
e. ODD (CD-ROM, Combo) drive or FDD drive in the Bay.
f. Hard-disk drive.
Note
Use the other memory card because it needs when operating computer.
4. Power on the computer.
5. Determine whether the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time.
(do not replace a non-defective FRU)
a. LCD Assembly (Check external monitor whether the same problem recurs or not).
b. Keyboard.
c. Keydeck (TouchPadand Scroll Button Assembly).
d. System board.
54
Chapter 5. Removing and replacing a part (FRU)
Note
-As for the screw, every Torque 3 0.2Kgfcm(0.196Nm)
-For further information on Removing and Replacing a Part(FRU), refer to Explore view.
Danger
Before removing any FRU, power off the computer, unplug all power cords from electrical
outlets, remove the battery pack, and then disconnect any interconnecting cables.
Caution
Before the computer is powered on after FRU replacement, make sure that all screws, springs,
and other small parts are in place and are not loose inside the computer. Verify metal flakes can
cause electrical short circuits.
Ch5. Removing and replacing a part
55
1010 Battery Pack
1. Push the battery latch in the direction shown below; then slide the battery pack out of the slot.
56
1020 System Door
Remove the following parts in order before replacing this part
a. Battery Pack(1010)
1. Remove the 3 screw.
2. Remove the System Door.
57
1030 WI FI
1. Remove 2 screws.
2. Remove the WI FI Cover.
58
1040 ODD
1EA FH + 2.5MM 6.5MM
SWRCH BZN
FAB30248901 1
Qty Specification FRU No. No.
1. Remove 1 screws.
2. Remove the ODD.
59
1050 HDD
1. Remove 2 screws.
2. Remove the HDD Cover.
60
3. Remove the HDD.
4. Remove 2 screws.
4EA
FH + 3MM 3.5MM
SWRCH SILVER
FAB30249001 1
61
3. Remove the HDD Shield.
62
1060 Bluetooth Module
a. Battery Pack(1010), b. HDD(1050)
1. Remove the Bluetooth Module.
63
1070 DIMM
a. Battery Pack(1010), b. System Door(1020)
1. Remove 2 Hooks than remove the DIMM.
Hook
Hook
64
1080 WLAN Module
1. Remove 3 Antenna Cables.
2. Remove the WLAN Module.
65
66
1090 CPU/GPU Fan Assembly
Connector
1. Remove 3 screws.
2. Remove the CPU/GPU Fan Assembly.
67
1100 Heatsync
1. Remove 3 screws.
2. Remove the Heatsync.
68
1110 CPU
1. Remove the CPU.
69
1120 Retainer
2. It uses J IG and it removes the Hooks.
1. Remove 3 screws.
3EA M2.5*3.0-I(BZN) FAB30255101 1
70
3. Remove the Retainer.
71
1130 Keyboard
a. Battery Pack(1010), b. Retainer(1120)
1EA
FH + 2.5MM 6.5MM
SWRCH BZN
FAB30248901 1
1. Remove 1 screws.
2. Remove 2 screws.
2EA M2.5*3.0-I(BZN) FAB30255101 1
72
Connector
4. Remove the Retainer Keyboard.
3. Remove the Keyboard Connector.
73
1140 Button Sub Board
a. Battery Pack(1010), b. Retainer(1070), c. Keyboard(1130 )
1. Remove the Cable.
2. Remove the Button Sub Board.
Cable
74
1150 Display Module
a. Battery Pack(1010), b. Retainer(1070), c. Keyboard(1130 )
1. Remove 2 screws.
2EA
FH + 2.5MM 6.5MM
SWRCH BZN
FAB30248901 1
2. Remove the Hinge Cap.
75
Connector
Connector
3. Remove the 2 Cable.
4. Remove the Display Module.
76
1160 Keyboard deck
a. Battery Pack(1010), b. Retainer(1070), c. Keyboard(1130 ) d. (1140), e. Display Module(1150)
1. Remove 12 screws.
2. Remove 5 screws.
12EA
FH + 2.5MM 6.5MM
SWRCH BZN
FAB30248901 1
3EA
FH + 2.5MM 6.5MM
SWRCH BZN
FAB30248901 1
2EA M2.5*3.0-I(BZN) FAB30255101 2
77
3. Remove the Keyboard deck.
78
1170 USB(R) Sub Board
a. Battery Pack(1010), b. Retainer(1070), c. Keyboard(1130 ) d. Button Sub Board(1140),
e. Display Module(1150) f. Keyboard deck(1160)
1EA
FH + 2.5MM 6.5MM
SWRCH BZN
FAB30248901 1
1. Remove 1 screws.
2. Remove the USB(R) Sub Board .
79
1180 Mainboard
e. Display Module(1150) f. Keyboard deck(1160) g. USB(R) Sub Board(1170)
Connector
Connector
2. Remove the Mainboard.
1. Remove Connector.
80
3. Remove the Mainboard.
81
1190 Modem Module
1. Remove the cables. Remove 2 screws.
2. Remove 6 screws.
e. Display Module(1150) f. Keyboard deck(1160) g. Mainboard(1180)
Cable
2EA M2.0*3.0-I-NI FAB30208501 1
82
1200 AC Connector
1. Remove 2 screws.
2EA M2.0*3.0-I-NI FAB30208501 1
2. Remove the AC Connector.
83
1210 Speaker
1. Remove 2 screws.
2EA M2.5*3.0-I(BZN) FAB30255101 1
2. Remove the Speaker.
84
1220 Battery Latch
1. Remove the Latch.
85
1230 LCD Front Case
a. Battery Pack(1010), b. WLAN Module(1060), c. Retainer(1070), d. Button Sub Board(1080)
e. Keyboard(1090)
1. Remove 2 cables.
No. FRU No. Specification Qty
1 FAB30248901
2.5MM 6.5MM
SWRCH BZN
4EA
2. Remove the LCD Front Case.
86
87
1240 LCD Assembly
a. Battery Pack(1010), b. Retainer(1070), d. Button Sub Board(1140), e. Display Module(1150)
F. LCD Front Case(1230)
1. Remove 2 cables.
No. FRU No. Specification Qty
1 FAB30248901
2.5MM 6.5MM
SWRCH BZN
4EA
2. Remove the LCD Assembly.
88
1250 LCD Panel
1. Remove 2 screws.
2. Remove the LCD Panel.
4EA M2.0*3.0-I-NI FAB30208501 1
F. LCD Front Case(1230)
89
4. Remove the inverter cable.
Cable
90
1260 Inverter
1. Remove 2 screws.
2. Remove the Inverter.
F. LCD Front Case(1230) g. LCD Assembly(1240)
Cable
Cable
91
1270 Web Cam Module
1. It uses J IG and it Remove the Web Cam module.
2. Remove the Web Cam Module.
F. LCD Front Case(1230) g. LCD Assembly(1240)
92
REV.10
Ch6. Part lists
Chapter 6. Part lists
Rear Case Assy (Red_LG) 3HQL8LC0010 QL8 LCD COVER ASSY-STANDARD ABQ67039901 NLCD07
Case Assembly NTP02 COVER Moonstone Front Case Assy(W/O Cam)
3IQL8LB0010 QL8 LCD BEZEL ASSY W/O/CC
ABQ67040002 NLCD06
Case Assembly NTP02 COVER Moonstone Front Case Assy(W Cam)
3IQL8LB0000 QL8 LCD BEZEL ASSY W/CCD
ABQ67040001 NLCD06
QCM M/B & LENS-C ASSY W/MIC W/O CAMERA EAB56601601 NLCD05
QCM M/B & LENS-C ASSY W/MIC FOR 1.3M NBC EBP56601301 NLCD05
AS023216302 7VTO20V 1.5KV 6.5MA 1 YES AS023216302 / T18I095.01/
Ampower Inverter for Moonstone, Citrine QUANTA COMPUTER INC.
EAY54657301 NLCD03
AS023216102 7VTO20V 1.65KV 6.5MA 1 YES AS023216102 / 10117.310-LF /
Sumida for Moonstone, Citrine QUANTA COMPUTER INC.
EAY54657201 NLCD03
LP154WE2-TLA3 WSXGA 15.4INCH 1680X1050 200CD COLOR 45% 16/9 500 -
LGPHILIPS-LCD
EAJ 37180101 NLCD02
LP154WX7-TLB3 WXGA 15.4INCH 1280X800 200CD COLOR 45% 16/10 500:1
LED TYPE LG Display Co. Ltd.
EAJ 58548901 NLCD04
LP154WX5-TLA1 WXGA 15.4INCH 1280X800 200CD COLOR 45% 16/10 600:1 -
LG PHILIPS LCD
EAJ 50624801 NLCD01
LP154WX4-TLC3 WXGA 15.4INCH 1280X800 200CD COLOR 45% 16/9 500 -
LG Display Nanjing Co., Ltd.
EAJ 37179501 NLCD01
LCD
4 LAYERS Moonstone QL8 USB AUDIO/B ASSY REV 0.1 EBR55692501 NSUB02
4 LAYERS Moonstone QL8 PW_BUTTON/B ASSY REV 0.1 EBR55692401 NSUB01
SUB
B/D
QL8 MB ASSY (INTEL,NB9M,QIM 256M) W/O CPU EBR56973001 NMLB01
QL8 MB ASSY (INTEL,NB9M HYN 256M) W/O CPU EBR56972701 NMLB01
QL8 MBASSY(INTEL,9P,SAM512M)WOCPU,RJ 11 EBR61046301 NMLB01
QL8 MBASSY(INTEL,9M,SAM256M)WOCPU,RJ 11 EBR61046401 NMLB01
QL8 MB (INTEL,9P,HYN 512M) W/O CPU,MODEM EBR56974201 NMLB01
QL8 MB ASSY(INTEL,9M,SAM256M)WO CPU EBR57797101 NMLB01
QL8 MB ASSY(GL40)W/O CPU W/O MODEM EBR58438801 NMLB01
QL8 MB ASSY(INTEL,9P,SAM512M)WOCPU EBR57590001 NMLB01
QL8 MB (INTEL,9P,QIM 512M) W/O CPU,MODEM EBR56974001 NMLB01
QL8 MB ASSY (INTEL,NB9P,HYN 512M) W/O CPU EBR56973601 NMLB01
QL8 MB (INTEL,9M,QIM 256M) W/O CPU,MODEM EBR56973301 NMLB01
QL8 MB (INTEL,UMA) W/O CPU,MODEM EBR55691531 NMLB01
QL8 MB ASSY (INTEL,NB9P,QIM 512M) W/O CPU EBR55691521 NMLB01
QL8 MB (INTEL,9M,HYN 256M) W/O CPU,MODEM EBR55691511 NMLB01
QL8 MB ASSY (INTEL,UMA) W/O CPU EBR55691501 NMLB01
M/B
Part Description LG P/N
Location
No.
Item
93
Ch6. Part lists
Location
No.
Item
CPU(478P) P8600 2.4G SLB3S(PGA)ROK B/S EAN51675901 NCPU01
CPU(478P) P8600 2.4G SLB3S(PGA)ROK B/S EAN51676001 NCPU01
CPU(478P) P7350 2.00G SLB53(PGA)ROK B/S EAN52856301 NCPU01
CPU
Robson 1.6 2G EAN51676901 NROB01
ROB
SON
SODIMM, 2G, DDR2, RBU256X64D2S800C6 ROK B/S EAN50048701 NMEM01
SODIMM, 2GB, DDR2, HYMP125S64CP8-S6 ROK B/S EAN48754401 NMEM01
MEM
ORY
AS036733016 8VTO21V 30V 20MA 1 YES For QL8 LED Driver inverter /
SUMIDA_IV10117/T-LF / QUANTA COMPUTER INC.
EAY60665801 NLCD17
TBD543NR 11VTO19V 26.3V 21MA 1 YES For QL8 LED Dirver Inverter /TDK/
QUANTA COMPUTER INC.
EAY60665401 NLCD17
Screw,Customized MS25065I007 FH +2.5MM 6.5MM SWRCH BZN
COMPUTER INC.
FAB30248901 NLCD16
Screw FAB30208501 NLCD15
Name Label RV510 Global Commercial MEZ54084804 NLCD14
Name Label RD510 Global Dos free MEZ54084803 NLCD14
Name Label RB510 Korea Commercial MEZ54084802 NLCD14
Name Label R510 Korea/Global Consummer MEZ54084801 NLCD14
Damper MOLD SILICON RUBBER NTP02 SILICON RUBBER Moonstone Front
GAQL8003010 LCD RUBBER QL8(GAQL8003,R3A)
MCQ55830301 NLCD13
Gasket COMPLEX EMI FABRIC . NTP02 Moonstone Gasket GBDT1009013
DT1_LCD_GASKET(GBDT1009,REV3A)
MDS55830401 NLCD12
Bracket COMPLEX NTP02 SUS HINGE Moonstone R FBQL8007010 HINGE R
SZS QL8(FBQL8007,R3A)
MAZ55830201 NLCD11
Bracket COMPLEX NTP02 SUS HINGE Moonstone L FBQL8006010 HINGE L
MAZ55826501 NLCD10
LCD Cable (WSXGA) EAD56808002 NLCD09
LCD Cable (WXGA) EAD56808001 NLCD08
Rear Case Assy (Gray_LG_HSDPA) Quanta 3HQL8LC0030 LG/SILVER/HSDPA ABQ67039906 NLCD07
Rear Case Assy (Red_LG_HSDPA) Quanta 3HQL8LC0000 QL8 LCD COVER
ASSY-HSPDA
ABQ67039905 NLCD07
Rear Case Assy (Gray_Xnote) Quanta 3HQL8LC0050
XNOTE/SILVER/STANDARD
ABQ67039904 NLCD07
Rear Case Assy (Gray_LG) Quanta 3HQL8LC0040 QL8 LCD COVER
ASSY/LG/SILVER/ST
ABQ67039903 NLCD07
Rear Case Assy (Red_Xnote) 3HQL8LC0020 QL8 LCD COVER ASSY-
STANDARD/NOTE
ABQ67039902 NLCD07
LCD
94
Ch6. Part lists
BLUETOOTH2.1+EDR USB MODULE QBT400UB 01P EAT56371601 NBLU01
Location
No.
Item
Bracket COMPLEX NTP02 SECC HDD Bracket 3IQT6HDTP00 QT6A HDD ASSY MAZ55830501 NHDD02
HDD(320G) MK3252GSX-GVL ROK B/S EAZ44349304 NHDD01
HDD(320G)MHZ2320BH CA07018-B438 ROK B/S EAZ52266906 NHDD01
HDD
K8NTP03 CD-ROM Citrine ODD Bezel Assy (S-Multi) 3AQL6CR0000 QL6 ODD
BEZEL ASSY
ACQ67103401 NODD03
QL8 ODD BEZEL ASSY (BLU-RAY) ACQ67041902 NODD03
QL8 ODD BEZEL ASSY ACQ67041901 NODD03
QL8 ODD BRACKET MAZ56929101 NODD02
QL8 ODD Moonstone BD read only EAZ59229901 NODD01
QL8 ODD SUPER MULTI MODULE S.P. EAZ56130601 NODD01
ODD
MODEM 56K(MDC) T60M951.42 EBM56371501 NMOD01
MODE
M
Bluetooth cable QL8 EAD60698101 NBLU02
B/T
WLAN 802.11 B/G/N 9WEM302QCE02Q (QMI) EBM54120701 NWLA01
WLAN 802.11 B/G/N 9WEM302QCF01Q EBM54120901 NWLA01
Intel WLAN Shirley Peak 1x2 ABG W/L 802.11A/B/G 512AGMMWG ROK B/S
FOR Russia,Ukraine,Pakistan
EBM54052001 NWLA01
Intel WLAN Shirley Peak 3x3 AGN EBM51208101 NWLA01
Intel WLAN Shirley Peak 1x2 AGN EBM51207601 NWLA01
WLAN
AW80577GG0411MA SLGJ N T4200 R-0 0.925V TO 1.125V 60A 2GHZ FCPGA
TR 478P INTEL
EAN60661301 NCPU01
AW80577GG0412MA SLGJ 4 T6400 R-0 1.0125V TO 1.15V 10A 2GHZ FCPGA
TR 478P INTEL
EAN60661201 NCPU01
AW80577GH0463M SLB54 P7450 M-0 1.05V TO 1.1625V 25A 2.13GHZ FCPGA
TR 478P INTEL
EAN60661401 NCPU01
LF80537NF0281MN QGGR SLB6J T1600 M-0 1.075V TO 1.175V 40A 1.66GHZ
FCPGA TR 468P INTEL
EAN56930402 NCPU01
LF80537GG041F QGFV SLB6E T5800 M-0 1.075V TO 1.175V 35A 2.2GHZ
FCPGA TR 468P INTEL
EAN56930202 NCPU01
LF80537GF0411M QBNT SLAVG T3200 M-0 1.075V TO 1.175V 35A 2GHZ
FCPGA TR 468P INTEL
EAN56930302 NCPU01
LF80537GF0481M QGFM SLB3P T3400 M-0 1.075V TO 1.175V 35A 2.16GHZ
FCPGA TR 468P INTEL
EAN56930301 NCPU01
CPU(478P) T9600 2.80GHz 1066MHz/6M (35W) EAN51675601 NCPU01
CPU(478P) T9400 2.53G SLB46(PGA)ROK B/S EAN51675701 NCPU01
CPU
95
Ch6. Part lists
Location
No.
Item
K/B(RUSSIAN)QL8(AEQL8700,REV3A)CNY AEW57431804 NKBD01
K/B(NORDIC)QL8(AEQL8N00,REV3A)CNY AEW57431808 NKBD01
K/B(KOREA)QL8(AEQL8Y00,REV3A)CNY AEW57431801 NKBD01
KEYB
OARD
Fan Block VGA PM MED55028501 NFAN02
Fan Block VGA PM MED55028801 NFAN02
Fan Module DIS PM EAL55488001 NFAN01
Fan Module DIS PM EAL55487501 NFAN01
Fan Module UMA GM EAL55489901 NFAN01
Fan Module UMA GM EAL55487701 NFAN01
FAN
K0A0415-037 LP-E03A LS-7 1.8M NONE 250V 2.5A H03VVH2-F 0.75x2 BLACK.
KETI N LINETECH CO
EAD50520401 NPOW01
DM333181Q73 plug, SP-022 connector, IS-034 1.83M NONE 250V 16A H05VV-F
0.75mm^2 x 3C CT-12 BLACK. CE(Europe) N QUANTA COMPUTER INC.
EAD55718603 NPOW01
DM333181Q06 plug, LP-E04 connector, LS-15 1.00 NONE 250V 7A H05VV-F
0.75mm^2 x 3C BLACK. KTL(Korea) N QUANTA COMPUTER INC.
EAD55718601 NPOW01
India 3P_SP-80A+H05VV-F 3G 0.75MM2+IS034 SP-80A IS034 1.83M NONE
250V 16A 3P CONN BLACK ISI N I-SHENG ELECTRIC WIRE & CABLE CO.,
LTD.
6410BW21601 NPOW01
Korea 3P_SP-022+IS-034 H05VV-F I-SHENG KS 1000MM 3P CONN
W/VELCRO TIE BLACK
6410BM21601 NPOW01
Australia 2P_R0A0415-030 LP-15A LS-7 1.8M NONE 250V 7.5A H03VVH2-F
0.75x2 BLACK. SAI(AUS) N LINETECH CO
EAD50544101 NPOW01
Argentina 2P_K0A0415-042 LP40 LS-7 1.8M NONE 250V 2.5A H03VVH2 0.75x2
BLACK. IRAM (Argentina) N LINETECH CO
EAD50520801 NPOW01
China 2P_K0A0415-007 PC205 COC03 1.8M NONE 250V 10A 52(RVV)
300/300V BLACK. CCC (China) Y LINETECH CO
EAD50520601 NPOW01
South Africa 2P EAD50485501 NPOW01
Finland, Norway, Sweden, Denmark, Germany, Poland, Turkey, Ukraine 2P EAD50481701 NPOW01
Canada, Mexico, Saudi Arabia 2P EAD50479201 NPOW01
HK, Nigeria, Singapore, UAE 2P EAD50476201 NPOW01
Israel 2P EAD30750802 NPOW01
POW
ERCO
DE
ADP 19V4.74A 90W(100-240V)PA-1900-08GK EAY52814001 NADA01
ADP 19V4.74A 90W(100-240V)PA-1900-08KI for India EAY52814002 NADA01
ADP 19V3.42A 65W(100-240V)SADP-65KB AFJ EAY44205002 NADA01
ADAP
TER
BATT LI,3UR18650-2-T0144,3S2P,4.4A Sanyo EAC34785413 NBAT01
BATT LI,916C7340F,3S2P,4.4A Simplo EAC34785411 NBAT01
BATT
ERY
96
Ch6. Part lists
Location
No.
Item
DC J ack+cable assy EAD60684401 NCHA08
Speaker+cable assy ACQ68582301 NCHA07
NTP02 COVER Moonstone Hinge R 3J QL8HA0010 QL8 LCD HINGE CAP ASSY
R
ABQ67039801 NCHA06
NTP02 COVER Moonstone Hinge L 3J QL8HA0000 QL8 LCD HINGE CAP ASSY
L
ABQ67039701 NCHA05
DD0QT6HD000 11 11 . Y Citrine HDD Cabel COMPUTER INC. EAD56807501 NCHA04
MOLD PC+ABS NTP02 PCABS DUMMY Moonstone SD EBQL8021010
SD_DUMMY_CARD QL8 (EBQL8021,R3A)
MCK55825901 NCHA03
MOLD PC+ABS NTP02 PCABS DUMMY Moonstone Card-Bus EBQL8020010
NEW_CARD_DUMMY QL8 (EBQL8020,R3A)
MCK55825801 NCHA03
NTP02 COVER Moonstone Wifi Door 39QL8CD0000 QL8 MINI CARD DOOR
ASSY
ABQ67039501 NCHA02
NTP02 COVER Moonstone Thermal Door 38QL8TD0000 QL8 THERMAL DOOR
ASSY
ABQ67039401 NCHA01
NTP02 COVER Moonstone HDD Door 37QL8HD0000 QL8 HDD DOOR ASSY ABQ67030701 NCHA01
CHAS
SIS,
MISC
NTP02 BOTTOM Moonstone W RJ 11 UMA 36QL8BC0020 QL8 BASE CASE
UMA ASSY
ABQ67030604 NBOT01
NTP02 BOTTOM Moonstone W/O RJ 11 UMA 36QL8BC0030 QL8 BASE CASE
WO RJ 11 UMA ASSY
ABQ67030603 NBOT01
NTP02 BOTTOM Moonstone W RJ 11 DIS 36QL8BC0000 QL8 BASE CASE
ASSY
ABQ67030602 NBOT01
NTP02 BOTTOM Moonstone Bottom W/O RJ 11 DIS 36QL8BC0010 QL8 BASE
CASE WO RJ 11 ASSY
ABQ67030601 NBOT01
BOTT
OM
NTP02 COVER Moonstone Retainer 35QL8KC0000 QL8 KB COVER ASSY ABQ67030501 NRET01
RETAI
NER
NTP02 KBD DECK Moonstone 34QL8TC0000 QL8 TOP CASE ASSY ABQ67030401 NDEC01
KBD
DECK
KBD protection sheet 3920BB3034D NKBD02
K/B(GREEK)QL8(AEQL8+00,REV3A)CNY AEW57431812 NKBD01
K/B(BRAZILIAN)QL8(AEQL8600,REV3A)CNY AEW57431813 NKBD01
K/B(PORTUGUESE)QL8(AEQL8T00,REV3A)CNY AEW57431811 NKBD01
K/B(HEBREW)QL8(AEQL8V00,REV3A)CNY AEW57431810 NKBD01
K/B(ARABIC)QL8(AEQL8Q00,REV3A)CNY AEW57431803 NKBD01
K/B(USA)QL8(AEQL8U00,REV3A)CNY AEW57431802 NKBD01
K/B(FR CANADA)QL8(AEQL8K00,REV3A)CNY AEW57431809 NKBD01
K/B(SPANISH)QL8(AEQL8P00,REV3A)CNY AEW57431807 NKBD01
K/B(TURKIS)QL8(AEQL8A00,REV3A)CNY AEW57431806 NKBD01
K/B(GERMAN)QL8(AEQL8G00,REV3A)CNY AEW57431805 NKBD01
KEYB
OARD
97
Ch6. Part lists
Location
No.
Item
PRINTING CPU Label NT PC '08 MeromCPU Label(Core 2 Duo) MEZ34321202 NLAB04
COMPLEX LABEL NT INTEL CENTRINO duo MOBILE TECH (Santarosa) from
2008
3850BB4551D NLAB04
PRINTING CPU Label NT PC Montevina Centrino2 MEZ51216901 NLAB04
PRINTING 1 Moonstone PRINTING POP LABEL Brazil MARKET MEZ55252207 NLAB03
PRINTING 1 Moonstone PRINTING POP LABEL HSDPA Ericsson MEZ49470201 NLAB03
PRINTING 1 Moonstone PRINTING POP LABEL AUSTRAILA MARKET MEZ55252204 NLAB03
PRINTING 1 Moonstone PRINTING POP LABEL GLOBAL & Au MARKET MEZ55252202 NLAB03
PRINTING 1 Moonstone PRINTING POP LABEL KOREA MARKET MEZ55252201 NLAB03
Caution Label for China MEZ51448104 NLAB02
Caution Label for Spanish MEZ51448103 NLAB02
Caution Label for English MEZ51448102 NLAB02
Caution Label for Korean MEZ51448101 NLAB02
Label_CUTTING PC ID Label Moonstone Mexico GM MEZ51836512 NLAB01
Label_CUTTING PC ID Label Moonstone Mexico PM MEZ51836511 NLAB01
Label_CUTTING PC ID Label Moonstone Global/China Commercial GM MEZ51836510 NLAB01
Label_CUTTING PC ID Label Moonstone Global/China Commercial PM MEZ51836509 NLAB01
Label_CUTTING PC ID Label Moonstone Global/China Free Dos GM MEZ51836508 NLAB01
Label_CUTTING PC ID Label Moonstone Global/China Free Dos PM MEZ51836507 NLAB01
Label_CUTTING PC ID Label Moonstone Global/China GM MEZ51836506 NLAB01
Label_CUTTING PC ID Label Moonstone Global/China PM MEZ51836505 NLAB01
Label_CUTTING PC ID Label Moonstone Korea Commercial GM MEZ51836504 NLAB01
Label_CUTTING PC ID Label Moonstone Korea Commercial PM MEZ51836503 NLAB01
Label_CUTTING PC ID Label Moonstone Korea GM MEZ51836502 NLAB01
Label_CUTTING PC ID Label Moonstone Korea PM MEZ51836501 NLAB01
LABE
L
SCREW M2.0*3.0-I-NI-NYLOK IRON FAB30208501 NSCR03
SCREW M2.5*3.0-I(BZN)(NYLON PATCH) IRON FAB30255101 NSCR02
SCREW M2.5*6.5-I(BZN(NYLOK-RED)D4.4 T0.8 FAB30248901 NSCR01
SCRE
W
CABLE FFC QL8 USB(142MM,REV2A)60V EAD57551201 NCHA14
CABLE FFC QL8 PB-MB(P0.5,8P,169MM,1A)60V EAD57551101 NCHA13
CPU thermal pad MCQ57697901 NCHA12
Battery Loker knob() MEY57697501 NCHA11
Battery Release knob spring MHY57697801 NCHA10
Foot rubber MDP57698901 NCHA09
CHAS
SIS,
MISC
98
Ch6. Part lists
Location
No.
Item
Nvidia 3858BZ9833C NLAB06
PRINTING VISTA LABEL NT DT ALL BASIC MODEL MEZ37782501 NLAB05
PRINTING VISTA LABEL NT DT ALL MODEL PRIMIUM MEZ37782601 NLAB05
COMPLEX CPU LABEL NT ALL INTEL PENTIUM PROCESSOR (from
09.01.01)*09.4.1 cut in
MEZ37690802 NLAB04
COMPLEX CPU LABEL NT ALL INTEL PENTIUM DUAL-CORE PROCESSOR MEZ37690801 NLAB04
LABE
L
A
A
A
A
B
B
B
B
B
B
NLCD11
NLCD07
NLCD06
NLCD05
NLCD01
NLCD04
NLCD13
NLCD13
NLCD13
NLCD13
NLCD12
NLCD08
NLCD03
NLCD017
NLCD10
NLCD14
NLCD13
NLCD13
A : NLCD15
B : NLCD16
R510 FRU_SBOM MASTER
Name Label RD510 Global Dos free MEZ54084803 NLCD14
Name Label RB510 Korea Commercial MEZ54084802 NLCD14
Name Label R510 Korea/Global Consummer MEZ54084801 NLCD14
Damper MOLD SILICON RUBBER NTP02 SILICON RUBBER Moonstone Front
GAQL8003010 LCD RUBBER QL8(GAQL8003,R3A)
MCQ55830301 NLCD13
Gasket COMPLEX EMI FABRIC . NTP02 Moonstone Gasket GBDT1009013
DT1_LCD_GASKET(GBDT1009,REV3A)
MDS55830401 NLCD12
Bracket COMPLEX NTP02 SUS HINGE Moonstone R FBQL8007010 HINGE R
MAZ55830201 NLCD11
Bracket COMPLEX NTP02 SUS HINGE Moonstone L FBQL8006010 HINGE L
MAZ55826501 NLCD10
LCD Cable (WSXGA) EAD56808002 NLCD09
LCD Cable (WXGA) EAD56808001 NLCD08
Rear Case Assy (Gray_LG_HSDPA) Quanta 3HQL8LC0030 LG/SILVER/HSDPA ABQ67039906 NLCD07
Rear Case Assy (Red_LG_HSDPA) Quanta 3HQL8LC0000 QL8 LCD COVER
ASSY-HSPDA
ABQ67039905 NLCD07
Rear Case Assy (Gray_Xnote) Quanta 3HQL8LC0050
XNOTE/SILVER/STANDARD
ABQ67039904 NLCD07
Rear Case Assy (Gray_LG) Quanta 3HQL8LC0040 QL8 LCD COVER
ASSY/LG/SILVER/ST
ABQ67039903 NLCD07
Rear Case Assy (Red_Xnote) 3HQL8LC0020 QL8 LCD COVER ASSY-
STANDARD/NOTE
ABQ67039902 NLCD07
Rear Case Assy (Red_LG) 3HQL8LC0010 QL8 LCD COVER ASSY-STANDARD ABQ67039901 NLCD07
Case Assembly NTP02 COVER Moonstone Front Case Assy (W/O Cam)
3IQL8LB0010 QL8 LCD BEZEL ASSY W/O/CC
ABQ67040002 NLCD06
Case Assembly NTP02 COVER Moonstone Front Case Assy (W Cam)
3IQL8LB0000 QL8 LCD BEZEL ASSY W/CCD
ABQ67040001 NLCD06
QCM M/B & LENS-C ASSY W/MIC W/O CAMERA EAB56601601 NLCD05
QCM M/B & LENS-C ASSY W/MIC FOR 1.3M NBC EBP56601301 NLCD05
AS023216302 7VTO20V 1.5KV 6.5MA 1 YES AS023216302 / T18I095.01/
Ampower Inverter for Moonstone, Citrine QUANTA COMPUTER INC.
EAY54657301 NLCD03
AS023216102 7VTO20V 1.65KV 6.5MA 1 YES AS023216102 / 10117.310-LF /
Sumida for Moonstone, Citrine QUANTA COMPUTER INC.
EAY54657201 NLCD03
LP154WE2-TLA3 WSXGA 15.4INCH 1680X1050 200CD COLOR 45% 16/9 500 -
LGPHILIPS-LCD
EAJ37180101 NLCD02
LP154WX7-TLB3 WXGA 15.4INCH 1280X800 200CD COLOR 45% 16/10 500:1
LED TYPE LG Display Co. Ltd.
EAJ58548901 NLCD04
LP154WX5-TLA1 WXGA 15.4INCH 1280X800 200CD COLOR 45% 16/10 600:1 -
LG PHILIPS LCD
EAJ50624801 NLCD01
LP154WX4-TLC3 WXGA 15.4INCH 1280X800 200CD COLOR 45% 16/9 500 -
LG Display Nanjing Co., Ltd.
EAJ37179501 NLCD01
LCD
Location
No.
Item
Location
No.
Item
SCRE
W
AS036733016 8VTO21V 30V 20MA 1 YES For QL8 LED Driver inverter /
SUMIDA_IV10117/T-LF / QUANTA COMPUTER INC.
EAY60665801 NLCD17
TBD543NR 11VTO19V 26.3V 21MA 1 YES For QL8 LED Dirver Inverter /TDK/
QUANTA COMPUTER INC.
EAY60665401 NLCD17
Screw,Customized MS25065I007 FH + 2.5MM 6.5MM SWRCH BZN COMPUTER
INC.
FAB30248901 NLCD16
Screw FAB30208501 NLCD15
LCD
NFAN02
NMEM01
NBLU01
NHDD01
NCPU01
NWLA01
NFAN01
NMEM01
NBOT01
LABEL
SCRE
W
NTP02 COVER Moonstone Retainer 35QL8KC0000 QL8 KB COVER ASSY ABQ67030501 NRET01
RETAI
NER
NTP02 KBD DECK Moonstone 34QL8TC0000 QL8 TOP CASE ASSY ABQ67030401 NDEC01
KBD
DECK
KBD protection sheet 3920BB3034D NKBD02
K/B(GREEK)QL8(AEQL8+00,REV3A)CNY AEW57431812 NKBD01
K/B(BRAZILIAN)QL8(AEQL8600,REV3A)CNY AEW57431813 NKBD01
K/B(PORTUGUESE)QL8(AEQL8T00,REV3A)CNY AEW57431811 NKBD01
K/B(HEBREW)QL8(AEQL8V00,REV3A)CNY AEW57431810 NKBD01
K/B(ARABIC)QL8(AEQL8Q00,REV3A)CNY AEW57431803 NKBD01
K/B(USA)QL8(AEQL8U00,REV3A)CNY AEW57431802 NKBD01
K/B(FR CANADA)QL8(AEQL8K00,REV3A)CNY AEW57431809 NKBD01
K/B(SPANISH)QL8(AEQL8P00,REV3A)CNY AEW57431807 NKBD01
K/B(TURKIS)QL8(AEQL8A00,REV3A)CNY AEW57431806 NKBD01
K/B(GERMAN)QL8(AEQL8G00,REV3A)CNY AEW57431805 NKBD01
K/B(RUSSIAN)QL8(AEQL8700,REV3A)CNY AEW57431804 NKBD01
K/B(NORDIC)QL8(AEQL8N00,REV3A)CNY AEW57431808 NKBD01
K/B(KOREA)QL8(AEQL8Y00,REV3A)CNY AEW57431801 NKBD01
KEYB
OARD
SUB
B/D
Location
No.
Item
09.01.01)*09.4.1 cut in
MEZ37690802 NLAB04
PRINTING CPU Label NT PC '08 Merom CPU Label(Core 2 Duo) MEZ34321202 NLAB04
2008
3850BB4551D NLAB04
LABEL
Location
No.
Item
NSUB02
NCHA14
NCHA08
NMLB01
NMOD01
NCHA07
NTP02 COVER Moonstone Hinge R 3JQL8HA0010 QL8 LCD HINGE CAP ASSY
R
ABQ67039801 NCHA06
NTP02 COVER Moonstone Hinge L 3JQL8HA0000 QL8 LCD HINGE CAP ASSY L ABQ67039701 NCHA05
MCK55825901 NCHA03
MCK55825801 NCHA03
ASSY
ABQ67039501 NCHA02
ASSY
ABQ67039401 NCHA01
CHA
SSIS,
MISC
MODEM 56K(MDC) T60M951.42 EBM56371501 NMOD01
MOD
EM
MEM
ORY
SUB
B/D
QL8 MBASSY(INTEL,9P,SAM512M)WOCPU,RJ11 EBR61046301 NMLB01
QL8 MBASSY(INTEL,9M,SAM256M)WOCPU,RJ11 EBR61046401 NMLB01
QL8 MB (INTEL,9P,HYN 512M) W/O CPU,MODEM EBR56974201 NMLB01
QL8 MB ASSY(INTEL,9M,SAM256M)WO CPU EBR57797101 NMLB01
QL8 MB ASSY(GL40)W/O CPU W/O MODEM EBR58438801 NMLB01
QL8 MB ASSY(INTEL,9P,SAM512M)WOCPU EBR57590001 NMLB01
QL8 MB (INTEL,9P,QIM 512M) W/O CPU,MODEM EBR56974001 NMLB01
QL8 MB ASSY (INTEL,NB9P,HYN 512M) W/O CPU EBR56973601 NMLB01
QL8 MB (INTEL,9M,QIM 256M) W/O CPU,MODEM EBR56973301 NMLB01
QL8 MB (INTEL,UMA) W/O CPU,MODEM EBR55691531 NMLB01
QL8 MB ASSY (INTEL,NB9P,QIM 512M) W/O CPU EBR55691521 NMLB01
QL8 MB (INTEL,9M,HYN 256M) W/O CPU,MODEM EBR55691511 NMLB01
QL8 MB ASSY (INTEL,UMA) W/O CPU EBR55691501 NMLB01
M/B
Location
No.
Item
SCR
EW
DC Jack+ cable assy EAD60684401 NCHA08
CHA
SSIS,
MISC
Location
No.
Item
NCHA04
NHDD02
NCHA02
NBAT01
NCHA09
NCHA09
NCHA15
NCHA09
NCHA09
NHDD02
NLAB01
NHDD01
NCHA16
NCHA03
NODD01
NCHA01
DC Jack+ cable assy EAD60684401 NCHA08
NTP02 COVER Moonstone Hinge R 3JQL8HA0010 QL8 LCD HINGE CAP ASSY
R
ABQ67039801 NCHA06
NTP02 COVER Moonstone Hinge L 3JQL8HA0000 QL8 LCD HINGE CAP ASSY
L
ABQ67039701 NCHA05
MCK55825901 NCHA03
MCK55825801 NCHA03
ASSY
ABQ67039501 NCHA02
ASSY
ABQ67039401 NCHA01
CHA
SSIS,
MISC
ADP 19V4.74A 90W(100-240V)PA-1900-08GK EAY52814001 NADA01
ADP 19V4.74A 90W(100-240V)PA-1900-08KI for India EAY52814002 NADA01
ADP 19V3.42A 65W(100-240V)SADP-65KB AFJ EAY44205002 NADA01
ADAP
TER
BATT
ERY
Bracket COMPLEX NTP02 SECC HDD Bracket 3IQT6HDTP00 QT6A HDD ASSY MAZ55830501 NHDD02
HDD
K8NTP03 CD-ROM Citrine ODD Bezel Assy (S-Multi) 3AQL6CR0000 QL6 ODD
BEZEL ASSY
ACQ67103401 NODD03
QL8 ODD BEZEL ASSY (BLU-RAY) ACQ67041902 NODD03
QL8 ODD BEZEL ASSY ACQ67041901 NODD03
QL8 ODD BRACKET MAZ56929101 NODD02
QL8 ODD Moonstone BD read only EAZ59229901 NODD01
QL8 ODD SUPER MULTI MODULE S.P. EAZ56130601 NODD01
ODD
Location
No.
Item
09.01.01)*09.4.1 cut in
MEZ37690802 NLAB04
PRINTING CPU Label NT PC '08 Merom CPU Label(Core 2 Duo) MEZ34321202 NLAB04
2008
3850BB4551D NLAB04
LABE
L
SCR
EW
CHA
SSIS,
MISC
Location
No.
Item
LABE
L
Location
No.
Item

LG R510 - SVC - Eng - 110725

Uploaded by

Copyright:

Available Formats

LG R510 - SVC - Eng - 110725

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG R510 - SVC - Eng - 110725

Uploaded by

Copyright:

Available Formats

1

16. Fan louvers

You might also like