Digital Electronics Lab Manual FOR 2/4 B.Tech (ECE) Course Code: Ec-253

BAPATLA ENGINEERING COLLEGE ECE DEPARTMENT
DIGITAL ELECTRONICS LAB MANUAL

FOR
2/4 B.Tech (ECE)
COURSE CODE: EC-253
PREPARED BY
D.SWETHA M.TECH, Lecturer

T Srinivasa Rao M.TECH, Lecturer
ECE DEPARTMENT
2011-2012

LIST OF EXPERIMENTS
S.No Name of the Experiment Page No

1. Realization of Gates using Discrete Components......................................................................01
2. Realization of Gates using Universal Building Block(NAND only)………………………….04
3. Design of Combinational Logic Circuits like Half-Adder, Full-Adder, Half- Subtractor and
Full-Subtractor………………………………………………………………………………...07
4. Verification of 4-Bit Magnitude Comparator…………………………………………………10
5. Design of Decoders like BCD-Decimal decoder……………………………………………...15
6. Applications of IC Parallel Adder(1’s and 2’s compliment addition)………………………..17
7. Design of Code Converters (Binary to Gray)…………………………………………………19
8. Design of Multiplexers/De Multiplexers ……………………………………………………..21
9. Verification of Truth Table of Flip-Flops using Gates………………………………………..23
10. Design of Shift register (To verify Serial to Parallel, Parallel to Serial ,Serial to Serial and
Parallel to Parallel Converters) using Flip-Flops……………………………………...……..26
11. Design of Ring & Johnson Counters using Flip-Flops………………………………………30
12. Conversion of Flip-Flops (JK-T, JK-D)……………………………………………...………32
13. Design of Binary/Decade Counter……………………………………………………...……34
14. Design Asynchronous Counter, Mod Counter, Up Counter, Down Counter and Up/Down
Counter……………………………………………………………………………………….36
15. Design Synchronous Counter, Mod Counter, Up Counter, Down Counter and Up/Down
Counter……………………………………………………………………………………….39


The Laboratory Notebook:
Each student must have their own laboratory notebook. All pre-lab exercises and
laboratory reports are to be entered into your notebook.
Your notebook must be clearly labelled on the cover with the following
information:
Module: Digital Electronics -

Name:
Register no: 4
Class:
Lab Partner Name:


STUDENTS GUIDELINES
There are 3 hours allocated to a laboratory session in Digital Electronics. It is a

necessary part of the course at which attendance is compulsory.
Here are some guidelines to help you perform the experiments and to submit the
reports:
1. Read all instructions carefully and carry them all out.

2. Ask a demonstrator if you are unsure of anything.
3. Record actual results (comment on them if they are unexpected!)
4. Write up full and suitable conclusions for each experiment.
5. If you have any doubt about the safety of any procedure, contact the
demonstrator beforehand.
6. THINK about what you are doing!


The Breadboard
The breadboard consists of two terminal strips and two bus strips (often broken in
the centre). Each bus strip has two rows of contacts. Each of the two rows of
contacts are a node. That is, each contact along a row on a bus strip is connected
together (inside the breadboard). Bus strips are used primarily for power supply
connections, but are also used for any node requiring a large number of
connections. Each terminal strip has 60 rows and 5 columns of contacts on each
side of the centre gap. Each row of 5 contacts is a node.
You will build your circuits on the terminal strips by inserting the leads of circuit
components into the contact receptacles and making connections with 22-26 gauge
wire. There are wire cutter/strippers and a spool of wire in the lab. It is a good
practice to wire +5V and 0V power supply connections to separate bus strips.


Fig 1. The breadboard. The lines indicate connected holes.

The 5V supply MUST NOT BE EXCEEDED since this will damage the ICs
(Integrated circuits) used during the experiments. Incorrect connection of power to
the ICs could result in them exploding or becoming very hot - with the possible
serious injury occurring to the people working on the experiment! Ensure that
the power supply polarity and all components and connections are correct
before switching on power .
Building the Circuit:
Throughout these experiments we will use TTL chips to build circuits. The steps
for wiring a circuit should be completed in the order described below:
1. Turn the power (Trainer Kit) off before you build anything!
2. Make sure the power is off before you build anything!
3. Connect the +5V and ground (GND) leads of the power supply to the
power and ground bus strips on your breadboard.
4. Plug the chips you will be using into the breadboard. Point all the chips in
the same direction with pin 1 at the upper-left corner. (Pin 1 is often
identified by a dot or a notch next to it on the chip package)
5. Connect +5V and GND pins of each chip to the power and ground bus
strips on the breadboard.
6. Select a connection on your schematic and place a piece of hook-up wire
between corresponding pins of the chips on your breadboard. It is better to
make the short connections before the longer ones. Mark each connection
on your schematic as you go, so as not to try to make the same connection
again at a later stage.
7. Get one of your group members to check the connections, before you
turn the power on.
8. If an error is made and is not spotted before you turn the power on. Turn
the power off immediately before you begin to rewire the circuit.
9. At the end of the laboratory session, collect you hook-up wires, chips and
all equipment and return them to the demonstrator.
10. Tidy the area that you were working in and leave it in the same condition
as it was before you started.

Common Causes of Problems:
1. Not connecting the ground and/or power pins for all chips.
2. Not turning on the power supply before checking the operation of the
circuit.
3. Leaving out wires.
4. Plugging wires into the wrong holes.
5. Driving a single gate input with the outputs of two or more gates
6. Modifying the circuit with the power on.
In all experiments, you will be expected to obtain all instruments, leads,

components at the start of the experiment and return them to their proper place after
you have finished the experiment. Please inform the demonstrator or technician if
you locate faulty equipment. If you damage a chip, inform a demonstrator, don't put
it back in the box of chips for somebody else to use.
Example Implementation of a Logic Circuit:
Build a circuit to implement the Boolean function F = /(/A./B), please note that the
notation /A refers to . You should use that notation during the write-up of your
laboratory experiments.


Quad 2 Input 7400 Hex 7404 Inverter
Fig 2. The complete designed and connected circuit
Sometimes the chip manufacturer may denote the first pin by a small indented
circle above the first pin of the chip. Place your chips in the same direction, to save
confusion at a later stage. Remember that you must connect power to the chips to
get them to work.

Useful IC Pin details
IC Description of IC
NUMBER
7400 Quad 2 input NAND GATE
7401 Quad 2input NAND Gate (open collector)
7402 Quad 2 input NOR Gate
7403 Quad 2 input NOR Gates (open collector)
7404 Hex Inverts
7421 Dual 4 input AND Gates
7430 8 input NAND Gate
7432 Quad 2 input OR Gates
7486 Quad 2 input EX-OR Gate
74107 Dual j-k Flip Flop
74174 Hex D Flip Flop
74173 Quad D Flip Flop
7474 Dual D Flip Flop
7475 Quad Bi-stable latch


7400(NAND)

7402(NOR)

7404(NOT)

7408(AND)

7420(4‐i/p NAND)

7411(3‐i/p AND)

7432(OR)

7486(EX-OR)

7410(3‐i/p NAND)

EXPERIMENT 1
REALIZATION OF GATES USING DISCRETE COMPONENTS
Aim: To construct logic gates OR, AND, NOT, NOR, NAND gates using discrete
components and verify their truth tables
Apparatus:
1. Electronic circuit designer
2. Resistors 10k,1k,220ohms
3. Transistors 2N2222(NPN)
4. Diodes 1N 4001
5. Connecting wires
Circuit Diagrams: TRUTH TABLE
OR Gate A B Y
D1N4002
0v 0v 0v
D1N4002 0v 5v 5v
Y
V1 V2 5v 0v 5v
A B
10k 5v 5v 5v
1
AND Gate
A B Y
+5V
0v 0v 0v
1k
0v 5v 0v
D1N4002
5v 0v 0v
Y
V2 D1N4002 5v 5v 5v
A B
NOT Gate
+5V
10k
A Y
Y 0v 5v
1k Q2N2222
5v 0v
A
NOR Gate
A B Y
+5V
0v 0v 5v
D1N4002
10 k
Y 0v 5v 0v
D1N4002 1k Q2N2222 5v 0v 0v
A B
5v 5v 0v
2
NAND Gate +5V
A B Y
1k 10 k
0v 0v 5v
D1N4002
Y 0v 5v 5v
D1N4002 D1N4002 Q2N2222 5v 0v 5v

A B
5v 5v 0v
Procedure:
1. Connections are made as per the circuit diagram
2. Switch on the power supply
3. Apply different combinations of inputs and observe the outputs; compare the outputs with the
truth tables.
Precautions:
All the connections should be made properly.
Result: Different logic gates are constructed and their truth tables are verified.
Questions:
1. Explain the operation of each circuit.
3
EXPERIMENT 2
REALIZATION OF GATES USING UNIVERSAL BUILDING

BLOCKS (NAND ONLY)
Aim: To construct logic gates NOT, AND, OR, EX-OR,EX-NOR of basic gates
using NAND gate and verify their truth tables .
Apparatus:
1. IC’s - 7400
2. Electronic Circuit Designer
3. Connecting patch chords.
Circuit Diagrams: TRUTH TABLE
NOT Gate
1 A Y
7400 3
A 2 Y
0v 5v
5v 0v
AND Gate A B Y
0v 0v 0v
1 1
A 7400 3 7400 3
2 2 Y 0v 5v 0v
B
5v 0v 0v
5v 5v 5v
4
OR Gate A B Y
1 0v 0v 0v
7400 3
A 2
Y 0v 5v 5v
1
7400 3
2 5v 0v 5v
1
7400 3 5v 5v 5v
B 2
EX-OR Gate A B Y
1
7400 3 0v 0v 0v
2
1 1 Y 0v 5v 5v
A 7400 3 7400 3
2 2
B 5v 0v 5v
1
7400 3
2 5v 5v 0v
EX-NOR Gate
1 A B Y
7400 3
2 0v 0v 5v
Y
1 1 1
A 7400 3 7400 3 7400 3
0v 5v 0v
2 2 2
5v 0v 0v
B 1
7400 3 5v 5v 5v
2
5
Procedure:
1. Connect the logic gates as shown in the diagrams.
2. Feed the logic signals 0 or 1 from the logic input switches in different combinations at the
inputs A & B.
3. Monitor the output using logic output LED indicators.
4. Repeat steps 1 to 3 for NOT, AND, OR, EX – OR & EX-NOR operations.

and compare the outputs with the truth tables.
Precautions:
1. All the connections should be made properly.
2. IC should not be reversed.
Result: Different logic gates are constructed using NAND gates and their truth tables are
verified.
Questions:
1. Why NAND & NOR gates are called universal gates?
2. Realize the EX – OR gates using minimum number of NAND gates?
3. Give the truth table for EX-NOR (EX-OR+NOT) and realize using NAND gates
.
4. Realize the given logic function using NAND gates?
f = ABC + ABC + ABC
6
EXPERIMENT 3
DESIGN OF COMBINATIONAL LOGIC CIRCUITS
Aim: - To design and construct Half-adder, Full-adder, Half-subtractor, Full- subtractor
Apparatus: -
1. IC’s - 7486, 7432, 7408, 7400

Circuit Diagram:- TRUTH TABLE
Half Adder:
A B S C
X 1 0 0 0 0
7486 3
2 S
Y 0 1 1 0
1 0 1 0
1 1 1 0 1
7408 3
2 C
Full Adder:
A B C N-1 S C
0 0 0 0 0
1
X 7486 3 1 S
2 3
0 0 1 1 0
Y 7486
2
0 1 0 1 0
0 1 1 0 1
Z 1 1 0 0 1 0
7408 3 1 C
2 7432 3 1 0 1 0 1
2
1 1 0 0 1
1
3
1 1 1 1 1
7408
2
7
Half Subtractor
1
X 7486 3 A B D B
2 D
0 0 0 0
Y
0 1 1 1
1 0 1 0
1
7408 3
B 1 1 0 0
1 7404 2 2
Full Subtractor
1
X 3 1
2 7486 7486 3
2 D
Y
Z
1
7408 3 1
1 7404 2 2 7432 3
2 B
1
7408 3
2
1 7404 2
A B C D B
N-1
0 0 0 0 0
0 0 1 1 1
0 1 0 1 1
0 1 1 0 1
1 0 0 1 0
1 0 1 0 0
1 1 0 0 0
1 1 1 1 1
8
Procedure: -
1. Verify the gates.
2. Make the connections as per the circuit diagram.
3. Switch on VCC and apply various combinations of input according to truth table.
4. Note down the output readings for half/full adder and half/full subtractor, Sum/difference and
the carry/borrow bit for different combinations of inputs verify their truth tables.
Precautions:
Result: Combinational logic circuits like Half-adder, Full-adder, Half-subtractor, Full-

subtractor are constructed and truth tables are verified.
Questions:
1. Describe the difference between half-adder and full-adder.
2. Describe the difference between half -subtractor and full-
subtractor.
9
EXPERIMENT 4
VERIFICATION OF 4-BIT MAGNITUDE COMPARATOR
Aim: - To verify the truth table of one bit and four bit comparators using logic Gates and
IC 7485
Apparatus : -
IC’s -7486, 7404, 7408 and 7485
Circuit diagrams:
10
IC 7486 (4 bit Magnitude comparator) pin configuration:
11
IC 7486 (4 bit Magnitude comparator) Logic diagram:
12
13
DESCRIPTION:
The 74F85 is a 4-bit magnitude comparator that can be expanded to almost any length.
It compares two 4-bit binary, BCD, or other monotonic codes and presents the three possible
magnitude results at the outputs. The 4-bit inputs are weighted (A0–A3) and (B0–B3) where A3
and B3 are the most significant bits. The operation of the74F85 is described in the Function
Table, showing all possible logic conditions. The upper part of the table describes the normal
operation under all conditions that will occur in a single device or in a series expansion scheme.
In the upper part of the table the three outputs are mutually exclusive. In the lower part of the
table, the outputs reflect the feed-forward conditions that exist in the parallel expansion scheme.
The expansion inputs IA>B, and IA=B and IA<B are the least significant bit positions.
When used for series expansion, the A>B, A=B and A<B outputs of the lease significant word
are connected to the corresponding IA>B, IA=B and IA<B inputs of the next higher stage. Stages
can be added in this manner to any length, but a propagation delay penalty of about 15ns is
added with each additional stage. For proper operation, the expansion inputs of the least
significant word should be tied as follows: IA>B = Low,
Procedure: -
1. Connect the circuit as shown in fig. Feed the 4-bit binary words A0, A1, A2 , A3 and B0, B1 ,
B2 , B3 from the logic input switches.
2. Pin 3 of IC 7485 should be at logic 1 to enable compare operation.
3. Observe the output A>B, A=B , and A<B on logic indicators. The outputs must be 1 or 0
respectively.
4. Repeat the steps 1 ,2 and 3 for various inputs A0 ,A1 , A2 , A3 and B0 , B1 , B2 , B3 and
observe the outputs at A>B , A=B and A<B .
Precautions:
Result: The truth tables of one bit and four bit magnitude comparators are verified.
Questions :-
1. What is Comparator?
2. What are the applications of Comparator?
3. Which logic is used as 1 bit comparator?
14
EXPERIMENT 5
DESIGN OF DECODERS LIKE BCD-DECIMAL DECODER
Aim: To design BCD-Decimal Decoder
Apparatus:
1. IC’s - 7432, 7400
Circuit Diagram:-
15
Truth Table:
Decimal Logic
Binary Inputs
Digit Function
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
Procedure:
3. Apply different combinations of inputs and observe the outputs; compare
the outputs with the truth tables.
Precautions: All the connections should be made properly.
Result: BCD-Decimal decoder is designed and truth table is verified.
16
EXPERIMENT 6
APPLICATIONS OF IC PARALLEL ADDER
(1’S AND 2’S COMPLIMENT ADDITION)
Aim: Design of 4-bit IC parallel adder
Apparatus : -
IC’s -7486, 7404, 7408 and 7485
Circuit diagrams:
Description:
The circuit performs addition as well as subtraction .When ‘s’ input is low the circuit
performs addition .The EX-OR gate acts as a controlled inverter (i.e., it inverts input when
control is high, otherwise it passes the input to the output).The output of EX-OR gate is B
when ‘s’ input is low .The output of the circuit is sum of two input numbers when ‘s’ input is
low .When ‘s’ input is HIGH the EX-OR gate acts as inverter and its output is the
complement of input .The carry input of the first full adder is ‘1’.The output of the circuit is
the sum A, complement of B and 1.This performs 2’s complement subtraction .The output of
the circuit is in true magnitude form if the A>B .The output of the circuit is in 2’s
complement form if the A<B.
17
Procedure:
3. Apply different combinations of inputs and observe the outputs.
Result: 4-bit IC parallel adder is designed and 1’s &2’s complement addition is performed
18
EXPERIMENT 7
DESIGN OF CODE CONVERTORS (BINARY TO GRAY AND GRAY TO

BINARYCONVERSION)
Aim: To design code converters and verify their truth tables
Apparatus:
1. IC - 7486
3.Connecting patch chords
Circuit Diagrams: Truth table
Binary to Gray Code Converter
B3 B2 B1 BO G3 G2 G1 G0
G3 0 0 0 0 0 0 0 0
B3 0 0 0 1 0 0 0 1
0 0 1 0 0 0 1 1
1
7486 3 G2
0 0 1 1 0 0 1 0
2
B2 0 1 0 0 0 1 1 0
0 1 0 1 0 1 1 1
0 1 1 0 0 1 0 1
0 1 1 1 0 1 0 0
1
1 0 0 0 1 1 0 0
7486 3 G1 1 0 0 1 1 1 0 1
B1 2
1 0 1 0 1 1 1 1
1 0 1 1 1 1 1 0
1 1 0 0 1 0 1 0
1 1 0 1 1 0 1 1
1
7486 3 G0 1 1 1 0 1 0 0 1
B0 2
1 1 1 1 1 0 0 0
19

Gray to Binary Code Converter

G3 B3
G3 G2 G1 GO B3 B2 B1 B0
0 0 0 0 0 0 0 0

1 0 0 0 1 0 0 0 1
7486 3
G2 2 B2 0 0 1 0 0 0 1 1
0 0 1 1 0 0 1 0
0 1 0 0 0 1 1 1
0 1 0 1 0 1 1 0
0 1 1 0 0 1 0 0
1
3
0 1 1 1 0 1 0 1
7486 B1
G1 2 1 0 0 0 1 1 1 1
1 0 0 1 1 1 1 0
1 0 1 0 1 1 0 0
1 0 1 1 1 1 0 1

1 1 1 0 0 1 0 0 0
7486 3 B0
G0 2
1 1 0 1 1 0 0 1
1 1 1 0 1 0 1 1
1 1 1 1 1 0 1 0
Procedure: -
1. The circuit connections are made as shown in fig.
2. Pin (14) is connected to +Vcc and Pin (7) to ground.
3 In the case of binary to gray conversion, the inputs B0, B1, B2 and B3 are given at
respective pins and outputs G0, G1, G2, G3 are taken for all the 16 combinations of the input.
4. In the case of gray to binary conversion, the inputs G0, G1, G2 and G3 are given at respective
Pins and outputs B0, B1, B2, and B3 are taken for all the 16 combinations of inputs.
5. The values of the outputs are tabulated.
Result: code converters are designed and their truth tables are verified.
Questions:
1. Convert binary 100100 to gray code.
20

EXPERIMENT 8
DESIGN OF MULTIPLEXERS/DEMULTIPLEXERS
Aim: To design Multiplexer and Demultiplexer and verify their truth tables
Apparatus:
1. IC - 7404,7411,7432,7408
3.Connecting patch chords
Circuit Diagrams: S1 S0 Y

0 0 I0
0 1 I1
1 0 I2
MULTIPLEXER 1 1 I3
S1 S0
1 7404 2 1 7404 2
1
2 7411 12
I0 13
1
7432 3
2
1
2 7411 12
I1 13
1
7432 3
2
1
2 7411 12
I2 13
1
7432 3
2
1
2 7411 12
I3 13
21

Demultiplexer
A B
1 7404 2 1 7404 2
1
7408 3
Y0 A B Y3 Y2 Y1 Y0
2
0 0 0 0 0 1
0 1 0 0 1 0
1
7408 3 1 0 0 1 0 0
2 Y1
1 1 1 0 0 0
1
7408 3
2 Y2
1
7408 3
2 Y3
Procedure:
3. Apply different combinations of inputs and observe the outputs; compare
the outputs with the truth tables.
Result: Multiplexer and Demultiplexer are constructed and the truth tables are verified
Questions:
1. What is the difference between multiplexer and decoder
22

EXPERIMENT 9
VERIFICATION OF TRUTH TABLES OF FLIPFLOPS USING GATES
Aim: ‐ To design and construct basic flip-flops R-S ,J-K,J-K Master slave flip-flops using gates
and verify their truth tables
Apparatus: ‐
1. IC’s - 7404, 7402, 7400
3. Connecting patch chords
Circuit Diagrams:-
Basic flipflop using NAND gates Truth Table
S R Q
0 0 Forbidden
0 1 1
1 0 0
1 1 No Change
Basic flipflop using NOR gates
S R Q
0 0 No Change
0 1 0
1 0 1
1 1 Forbidden
23

R-S flip-flop using NAND gates
S R Q
0 0 No Change
0 1 0
1 0 1
1 1 Forbidden
J-k flip-flop using NAND gates
J K Q
0 0 No Change
0 1 0
1 0 1
1 1 Race around
24

J-K Master Slave using NAND gates
J K Q
0 0
0 1 0
1 0 1
1 1
Procedure:
1. Connect the Flip-flop circuits as shown above.
2. Apply different combinations of inputs and observe the outputs

Result: Different Flip-flops using gates are constructed and their truth tables are verified
Questions: 1.List four Basic Flip-flop applications?

2. What advantage does a J-K Flip-flop have over an S-R?
3. What is meant by Race around condition?
25

EXPERIMENT 10
DESIGN OF SHIFT REGISTER(TO VERIFY SERIAL TO

PARALLEL,PARALLEL TO SERIAL,SERIAL TO SERIAL,PARALLEL
TO PARALLEL)USING FLIP-FLOPS
Aim:- To study shift register using IC 7495 in all its modes i.e.
SIPO/SISO, PISO/PIPO.
Apparatus: - IC 7495, etc.
Circuit diagram :‐

26

PISO:‐
27

Procedure :
Serial In Parallel Out(SIPO):

1. Connections are made as per circuit diagram.
2. Apply the data at serial i/p
3. Apply one clock pulse at clock 1 (Right Shift) observe this data at QA.
4. Apply the next data at serial i/p.
5. Apply one clock pulse at clock 2, observe that the data on QA will shift to
QB and the new data applied will appear at QA.
6. Repeat steps 2 and 3 till all the 4 bits data are entered one by one into the
shift register.
Serial In Serial Out (SISO):

2. Load the shift register with 4 bits of data one by one serially.
3. At the end of 4th clock pulse the first data ‘d0’ appears at QD.
4. Apply another clock pulse; the second data ‘d1’ appears at QD.
5. Apply another clock pulse; the third data appears at QD.
6. Application of next clock pulse will enable the 4th data ‘d3’ to appear at
QD. Thus the data applied serially at the input comes out serially at QD
Parallel In Serial Out (PISO):

2. Apply the desired 4 bit data at A, B, C and D.
28

3. Keeping the mode control M=1 apply one clock pulse. The data applied at
A, B, C and D will appear at QA, QB, QC and QD respectively.
4. Now mode control M=0. Apply clock pulses one by one and observe the
Data coming out serially at QD
Parallel In Parallel Out (PIPO):

2. Apply the 4 bit data at A, B, C and D.
3. Apply one clock pulse at Clock 2 (Note: Mode control M=1).
4. The 4 bit data at A, B, C and D appears at QA, QB, QC and QD
respectively.
Result: shift registers using IC 7495 in all its modes i.e.SIPO/SISO, PISO/PIPO are verified.
29

EXPERIMENT 11
DESIGN OF RING AND JOHNSON COUNTERS USING FLIP-FLOPS
Aim: To design Ring counter and Johnson counter and verify their truth tables
Apparatus:
1. IC’s - 7404, 7402, 7400
Circuit Diagram:
Ring Counter:
Truth Table
Clk Q3 Q2 Q1
0 0 0 1
1 1 0 0
2 0 1 0
30

Johnson Counter:
Truth Table
Clk Q3 Q2 Q1
0 0 0 0
1 1 0 0
2 1 1 0
3 1 1 1
4 0 1 1
5 0 0 1
Procedure:
2. Switch on the power supply.
3. Apply clock pulses and note the outputs after each clock pulse
Precautions:
Result: Ring counter and Johnson counter are designed and their truth tables are verified.
31

EXPERIMENT 12
CONVERTION OF FLIP-FLOPS (JK-T,JK-D)
Aim: To design and construct T and D Flip-flop from JK- flip-flop and verify their truth
tables
Apparatus:
1. IC’s - 7410, 7400
Circuit diagram:
T-Flip Flop
D-Flip Flop
32

Procedure:
3. Apply different combinations of inputs and observe the out puts
Precautions:
Result: T and D Flip-flop are designed and constructed from JK- flip-flop and their truth
tables are verified.
33

EXPERIMENT 13
DESIGN OF BINARY/DECADE COUNTER
Aim: To design and construct decade counter and verify the truth table
Apparatus:
1. IC’s - 7410, 7400
Circuit diagram:
Decade
Counter:
Truth Table
CLK Q3 Q2 Q1 Q0

0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 1 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 1 0 0 1
34

Procedure:
3. Apply clock pulses and note the outputs after each clock pulse and note done the out puts Q3,
Q2, Q1, Q0.
Precautions:
Result: Decade counter is designed and truth tables are verified.
35

EXPERIMENT 14
DESIGN OFASYNCHRONOUS COUNTER, MOD COUNTER,

UP COUNTER, DOWN COUNTER AND UP/DOWN COUNTER
USING FLIP FLOPS
Aim:- To design and construct of 3-bit Asynchronous up and down counters,2-bit up/down
counter.
Apparatus:
1. IC’s - 7408,7476,7400,7432
Circuit Diagram:
3-bit Asynchronous up counter:

36


3-bit Asynchronous down counter:

TRUTH TABLE
37


Two Bit up/Down Counter using negative edge-triggered flip-
flops
WHEN M=1 WHEN M=0
CLK Q2 Q1

0 1 1
1 1 0
38

2 0 1
CLK Q2 Q1 3 0 0
0 0 0
1 0 1

2 1 0
3 1 1

Procedure:
3. Apply clock pulses and note the outputs after each clock pulse and note done the out puts.
Precautions:
Result: 3-bit Asynchronous up and down counters,2-bit up/down counter are designed and
truth tables are verified.
39

EXPERIMENT 15
DESIGN OF SYNCHRONOUS COUNTER, MOD COUNTER,

UP COUNTER, DOWN COUNTER AND UP/DOWN COUNTER
USING FLIP FLOPS
Aim:- To design and construct of 3-bit Synchronous up and down counters,2-bit up/down
counter.
Apparatus:
1. IC’s - 7408,7476,7400,7432
Circuit Diagram:
40

Truth Table
Two Bit up/Down Counter using negative edge-triggered flip-flops
WHEN M=1 WHEN M=0

CLK Q2 Q1 CLK Q2 Q1
0 0 0
0 1 1
1 0 1 1 1 0

2 1 0 2 0 1
3 1 1 3 0 0
41

Procedure:
3. Apply clock pulses and note the outputs after each clock pulse and note done the out puts.
Precautions:
Result: 3-bit Synchronous up and down counters,2-bit up/down counter are designed and
truth tables are verified.
42

Digital Electronics Lab Manual FOR 2/4 B.Tech (ECE) Course Code: Ec-253

Uploaded by

Copyright:

Available Formats

Digital Electronics Lab Manual FOR 2/4 B.Tech (ECE) Course Code: Ec-253

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Digital Electronics Lab Manual FOR 2/4 B.Tech (ECE) Course Code: Ec-253

Uploaded by

Copyright:

Available Formats

BAPATLA ENGINEERING COLLEGE ECE DEPARTMENT

DIGITAL ELECTRONICS LAB MANUAL

D.SWETHA M.TECH, Lecturer

S.No Name of the Experiment Page No

2. Realization of Gates using Universal Building Block(NAND only)………………………….04

4. Verification of 4-Bit Magnitude Comparator…………………………………………………10

5. Design of Decoders like BCD-Decimal decoder……………………………………………...15

6. Applications of IC Parallel Adder(1’s and 2’s compliment addition)………………………..17

7. Design of Code Converters (Binary to Gray)…………………………………………………19

8. Design of Multiplexers/De Multiplexers ……………………………………………………..21

9. Verification of Truth Table of Flip-Flops using Gates………………………………………..23

Parallel to Parallel Converters) using Flip-Flops……………………………………...……..26

11. Design of Ring & Johnson Counters using Flip-Flops………………………………………30

12. Conversion of Flip-Flops (JK-T, JK-D)……………………………………………...………32

13. Design of Binary/Decade Counter……………………………………………………...……34

The Laboratory Notebook:

Module: Digital Electronics -

There are 3 hours allocated to a laboratory session in Digital Electronics. It is a

1. Read all instructions carefully and carry them all out.

6. THINK about what you are doing!

Fig 1. The breadboard. The lines indicate connected holes.

Building the Circuit:

Common Causes of Problems:

In all experiments, you will be expected to obtain all instruments, leads,

Example Implementation of a Logic Circuit:

Fig 2. The complete designed and connected circuit

Useful IC Pin details

7421 Dual 4 input AND Gates

7430 8 input NAND Gate

7432 Quad 2 input OR Gates

7486 Quad 2 input EX-OR Gate

74107 Dual j-k Flip Flop

74109 Dual j-k Flip Flop

74174 Hex D Flip Flop

74173 Quad D Flip Flop

7473 Dual j-k Flip Flop

7474 Dual D Flip Flop

7475 Quad Bi-stable latch

7476 Dual j-k Flip Flop

REALIZATION OF GATES USING DISCRETE COMPONENTS

Circuit Diagrams: TRUTH TABLE

NAND Gate +5V

D1N4002 D1N4002 Q2N2222 5v 0v 5v

2. Switch on the power supply

1. Explain the operation of each circuit.

REALIZATION OF GATES USING UNIVERSAL BUILDING

Circuit Diagrams: TRUTH TABLE

3. Monitor the output using logic output LED indicators.

4. Repeat steps 1 to 3 for NOT, AND, OR, EX – OR & EX-NOR operations.

2. IC should not be reversed.

2. Realize the EX – OR gates using minimum number of NAND gates?

f = ABC + ABC + ABC

DESIGN OF COMBINATIONAL LOGIC CIRCUITS

Aim: - To design and construct Half-adder, Full-adder, Half-subtractor, Full- subtractor

1. IC’s - 7486, 7432, 7408, 7400

Circuit Diagram:- TRUTH TABLE

2. Make the connections as per the circuit diagram.

2. IC should not be reversed.