Armaflex 520 MSDS

MATERIAL SAFETY DATA SHEET
I. PRODUCT IDENTIFICATION
Name: Armaflex 520 Adhesive
Description: Solvent-dispersed synthetic rubber resin adhesive
II. DEPARTMENT OF TRANSPORTATION INFORMATION
SHIPPING NAME: Adhesive containing a flammable liquid (Hexane and Acetone)
HAZARD CLASS: 3 (flammable liquid) ID#: UN1133 PG: II (Armaflex 520 adhesive)
REPORTABLE QUANTITY (RQ): 6250 lbs.
EMERGENCY ONLY CONTACT: CHEM-TEL 1-800-255-3924
III. HMIS (0=Minimal hazard; 4=severe hazard)
Health = 2 Flammability =3 Reactivity = 0
IV. PRODUCT CONTENT
This product contains chemicals subject to the reporting requirements of Section 313 of
Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR Part
372. All components are on TSCA inventory. This product does NOT contain asbestos
or polychlorinated biphenyls.
V. HAZARDOUS INGREDIENTS
INGREDIENT: CAS Number
Acetone 67-64-1
Toluene 108-88-3
Hexane 110-54-3

PERCENT:
25-27%

16-18%

35-37%

OSHA PEL ACGIH TLV
750 ppm 500 ppm
STEL 1000 ppm STEL 750 ppm
100 ppm 50 ppm
STEL 150 ppm (skin)
50 ppm 50 ppm (skin)

VI. PHYSICAL DATA
APPEARANCE AND COLOR: Straw colored liquid with characteristic solvent
odor. BOILING POINT: (F): >152. VAPOR PRESSURE: (mm Hg @ 20C)
180. VAPOR DENSITY: (air=1) N/K. SOLUBILITY IN WATER: Negligible.
SPECIFIC GRAVITY: (water=1): 0.82. PERCENT VOLATILE BY WEIGHT (30
minutes @ 275 F): 79.0%. EVAPORATION RATE: (butyl acetate =1): N/K.
VISCOSITY 155-195 cps. pH: N/K VOC: 596 g/L calculated at 70F,
SCAQMD.
VII. FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: -4F based on acetone (CC). FLAMMABLE RANGE: LEL =
1.1, UEL = 13.0 (based on hexane and acetone). EXTINGUISHING MEDIA:
Carbon dioxide, dry chemical alcohol-type foam. SPECIAL FIRE FIGHTING
PROCEDURES: Protect fire fighters from toxic products of combustion by
wearing self-contained breathing apparatus. UNUSUAL FIRE AND
EXPLOSION HAZARDS: Closed containers in a fire may rupture due to
pressure build up. Use water to cool containers to prevent this.
VIII. HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation and direct dermal exposure.
TARGET ORGANS: Upper respiratory tract, skin and eyes. EFFECTS OF
OVEREXPOSURE: Skin and Eyes: Excessive skin contact may cause drying
and cracking of skin, deffating of tissue and result in dermatitis. Contact with
eyes will cause irritation. INHALATION: May cause irritation of respiratory tract,
coughing and CNS effects, such as headache, dizziness, and nausea.
CARCINOGENICITY: NTP: No. IARC Monographs: No. OSHA Regulated: No.
MEDICAL CONTITIONS GENERALLY AGGRAVATED BY EXPOSURE: Any
condition generally aggravated by solvents; preexisting upper respiratory and
lung disease such as, but not limited to, bronchitis, emphysema and asthma.
FIRST AID PROCEDURES: SKIN AND EYES: Flush any skin or eye contact
with plenty of water. Additionally with skin contact, wash skin thoroughly with
soap and water. Refer to physician if irritation persists. INHALATION:
Remove to fresh air if exposed to excess concentration of vapor. Seek medical
attention if symptoms persist. INGESTION: Do not induce vomiting. Call
Poison control center or physician for guidance.
IX. REACTIVITY DATA
STABILITY: Stable. INCOMPATIBILITY: Strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon
dioxide and other toxic vapors and gases that are common to thermal
degradation f organic compounds. HARZARDOUS POLYMERIZATION: Will
not occur.
X. SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Remove all
sources of ignition. Ventilate are of spill or leak, if using mechanical ventilation,
make sure that it is explosion proof or does not present an ignition source. For
exposures above TLV, wear approved respiratory equipment. Contain spill and
prevent it from entering sewer lines or waterways. Use absorbent to assist with
the pick up of material. Scrape up adhesive and place in container. WATE
DISPOSAL METHOD: Dispose of container and any unused contents in
accordance with federal, state and local waste disposal regulations. Do not flush
unused contents or residue down drains. Do not reuse container.
XI. SAFE HANDLING AND USE INFORMATION
VENTILATION: Extremely flammable vapors may ignite explosively or cause
flash fire. Use natural cross ventilation, local (mechanical) pick up or general
area (mechanical) ventilation to prevent accumulation of solvent vapors, keeping
in mind that the ventilation pattern must remove the heavier than air solvent
vapors from the lower levels of the work spaces. The ventilation should be
sufficient to keep the solvent vapor concentration below the TLV.
RESPIRATORY PROTECTION: With adequate ventilation, respiratory
equipment should not be needed. If adequate ventilation is not afforded, wear
respiratory equipment approved for organic vapors. SKIN AND EYE
PROTECTION: During the manufacture and packaging of this product,
impervious gloves, eye protection and eye wash station may be appropriate.
During normal end product use, cotton or loop-pile gloves and safety glasses are
recommended to prevent contact with this mastic product.
XII. SPECIAL PRECAUTIONS
PRECAUSTIONS TO BE TAKEN IN HANDELING AND STORAGE: Store in an
area suitable for flammable mixtures. Recommended storage temperature is
below 90F. OTHER PRECAUTIONS: Vapors are flammable and are heavier
than air. Prohibit smoking and eliminate all other sources of ignition, such as
regular electric tools and appliances. Make sure that pilot lights on gas fired
water heaters are extinguished. WARNING: This product contains toluene, a
chemical known to the state of California to cause birth defects or other
reproductive harm. WORKSITE ENVIRONMENT: Initially there may be a
potential adverse impact on indoor air quality within the general work area during
instillation. Therefore, you should advise the building manager or other
appropriate person that; it will be necessary to establish and maintain adequate
ventilation of the work area, without causing the entry of contaminates to other
parts of the building. Persons who are sensitive to odors and/or chemicals
should avoid the work area during this process.
The information presented herein is supplied as a guide to those who handle or use this
product. Safe work practices must be employed when working with any materials. It is
important that the end user makes a determination regarding the adequacy of the safety
procedures employed during the use of this product.

ARMAFLEX
520 ADHESIVE
Prepared 8/10 replaces 6/09
Made in USA for
Armacell LLC
7600 Oakwood Street Extension
Mebane, NC 27302
(919)-304-3846

Armaflex 520 MSDS

Uploaded by

Copyright:

Available Formats

Armaflex 520 MSDS

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Armaflex 520 MSDS

Uploaded by

Copyright:

Available Formats

MATERIAL SAFETY DATA SHEET

You might also like