Technical Data ACOPOS Servo Family

1.5 ACOPOS 1022, 1045, 1090

1.5.1 Order Data
Model Number Short Description Servo Drives 8V1022.00-2 8V1045.00-2 8V1090.00-2 Servo drive 3 x 400-480V 2.2A 1kW, line filter, braking resistor and electronic secure restart inhibit integrated Image

Servo drive 3 x 400-480V 8.8A 4kW, line filter, braking resistor and electronic secure restart inhibit integrated Accessories

8AC110.60-2 8AC112.60-1 8AC120.60-1 8AC122.60-2 8AC123.60-1 8AC130.60-1

ACOPOS plug-in module, CAN interface ACOPOS plug-in module, ETHERNET Powerlink interface ACOPOS plug-in module, EnDat encoder interface ACOPOS plug-in module, resolver interface ACOPOS plug-in module, incremental encoder and SSI absolute encoder interface ACOPOS plug-in module, 8 digital I/O configurable in pairs as 24V input or as output 400/100mA, 2 digital outputs 2A, Order TB712 terminal block separately ACOPOS plug-in module, 2 analog inputs 10V, 2 digital I/O points which can be configured as a 24V input or 45mA output, Order TB712 terminal block separately ACOPOS plug-in module, CPU, x86 100 MHz Intel compatible, 8 MB DRAM, 32 kB SRAM, exchangeable application memory: Compact Flash, 1 CAN interface, 1 Profibus-DP Slave interface, 1 RS232 interface, order program memory separately! ACOPOS plug-in module, CPU, ARNC0, x86 100 MHz Intel compatible, 16 MB DRAM, 32 kB SRAM, exchangeable application memory: Compact Flash, 1 CAN interface, 1 Profibus-DP slave interface, 1 RS232 interface, order application memory separately! 24 VDC power supply, 3-phase, 20 A, input 400..500 VAC (3 phases), wide range, DIN rail mounting

8AC131.60-1

8AC140.60-1

8AC140.61-2

0PS320.1

Table 10: Order data for ACOPOS 1022, 1045, 1090

ACOPOS User's Manual V 1.3.1

43

Chapter 2 Technical Data

Servo drive 3 x 400-480V 4.4A 2kW, line filter, braking resistor and electronic secure restart inhibit integrated

Technical Data ACOPOS Servo Family 1.5.2 Technical Data

Product ID General Information C-UL-US Listed Power Mains Connection Mains Input Voltage 3 x 400 VAC to 480 VAC 10 % Power filter according to IEC 61800-3-A11 second environment (Limits from CISPR11, Group 2, Class A) 50 / 60 Hz 4% Max. 3 kVA 4A Max. 5 kVA 7A > 10 s Approx. 120 W Approx. 180 W Approx. 200 W Max. 10 kVA 7A Yes 8V1022.00-2 8V1045.00-2 8V1090.00-2

Frequency Installed Load Starting Current at 400 VAC Switch-on Interval Power Loss at Max. Device Power without Braking Resistor 24 VDC Supply Input Voltage 1) Input Capacitance Current Requirements 2) DC Bus DC Bus Capacitance Motor Connector Continuous Current 3) Reduction of Continuous Current Depending on Environmental Temperature 4) Mains Input Voltage: 400 VAC Switching Frequency 20 kHz Switching Frequency 10 kHz Switching Frequency 5 kHz Mains Input Voltage: 480 VAC Switching Frequency 20 kHz Switching Frequency 10 kHz Switching Frequency 5 kHz Reduction of Continuous Current Depending on Altitude Starting at 500 m Above Sea Level Peak Current Nominal Switching Frequency Maximum Motor Line Length Protective Measures Motor Holding Brake Connection Maximum Output Current Protective Measures 2.2 Aeff 235 F

24 VDC +25 % / -25 % 8200 F Max. 2.5 A + current for motor holding brake

470 F

4.4 Aeff

8.8 Aeff

No reduction No reduction No reduction 0.13 Aeff per C ( 51 C) No reduction No reduction

0.13 Aeff per C ( 45 C) No reduction No reduction 0.13 Aeff per C ( 35 C) No reduction No reduction

0.18 Aeff per C ( 30 C) 0.18 Aeff per C ( 54 C) No reduction 0.18 Aeff per C ( 18 C) 0.18 Aeff per C ( 48 C) No reduction

0.22 Aeff per 1000 m 14 Aeff 20 kHz

0.44 Aeff per 1000 m 24 Aeff 25 m Short circuit and ground fault protection

0.88 Aeff per 1000 m 24 Aeff 10 kHz

1A Short circuit and ground fault protection

Table 11: Technical data for ACOPOS 1022, 1045, 1090

44

ACOPOS User's Manual V 1.3.1

Technical Data ACOPOS Servo Family

Product ID Braking Resistor Peak Power Output Continuous Power Output Trigger Inputs Number of Inputs Wiring Electrical Isolation Input - ACOPOS Input - Input Input Voltage Nominal Maximum Switching Threshold LOW HIGH Input Current at Nominal Voltage Switching Delay Modulation Compared to Ground Potential Limit Switch and Reference Inputs Number of Inputs Wiring Electrical Isolation Input - ACOPOS Input - Input Input Voltage Nominal Maximum Switching Threshold LOW HIGH Input Current at Nominal Voltage Switching Delay Modulation Compared to Ground Potential Enable Input Number of Inputs Wiring Electrical Isolation Input - ACOPOS Input Voltage Nominal Maximum Switching Threshold LOW HIGH Input Current at Nominal Voltage 1 Sink Yes 24 VDC 30 VDC <5V >15 V Approx. 30 mA 3 Sink Yes No 24 VDC 30 VDC <5V >15 V Approx. 4 mA Max. 2.0 ms Max. 38 V 2 Sink 3.5 kW 130 W 7 kW 200 W 7 kW 200 W 8V1022.00-2 8V1045.00-2 8V1090.00-2

24 VDC 30 VDC <5V >15 V Approx. 10 mA Max. 55 s (digitally filtered) Max. 38 V

Table 11: Technical data for ACOPOS 1022, 1045, 1090 (Forts.)

ACOPOS User's Manual V 1.3.1

45

Chapter 2 Technical Data

Yes No

Technical Data ACOPOS Servo Family

Product ID Switching Delay Enable 1 -> 0, PWM Off Enable 0 -> 1, Ready for PWM Modulation Compared to Ground Potential Operational Conditions Environmental Temperature During Operation Max. Environmental Temperature 5) Relative Humidity During Operation Installation at Altitudes Above Sea Level Maximum Installation Altitude 6) Degree of Pollution According to IEC 60664-1 Over-voltage Category According to IEC 60364-4-443:1999 Protection According to IEC 60529 Storage and Transport Conditions Storage Temperature Relative Humidity During Storage Transport Temperature Relative Humidity During Transport Mechanical Characteristics Dimensions Width Height Depth Weight 4.0 kg 70.5 mm 375 mm 235.5 mm 4.1 kg 4.4 kg -25 to +55 C 5 to 95%, non-condensing -25 to +70 C 95 % at +40 C 0 to 50 C +55 C 5 to 95%, non-condensing 0 to 500 m 2000 m 2 (non-conductive material) II IP20 8V1022.00-2 8V1045.00-2 Max. 2.0 ms Max. 100 s Max. 38 V 8V1090.00-2

Table 11: Technical data for ACOPOS 1022, 1045, 1090 (Forts.)
1) When using motor holding brakes, the valid input voltage range is reduced. The input voltage range should be selected so that the proper supply voltage for the motor holding brake can be maintained. 2) The current requirements depend on the configuration of the ACOPOS servo drive. 3) Valid in the following conditions: Mains input voltage 400 VAC, nominal switching frequency, 40 C environmental temperature, installation altitudes < 500 m above sea level. 4) The nominal switching frequency values for the respective ACOPOS servo drive are marked in bold. 5) Continuous operation of ACOPOS servo drives at environmental temperatures ranging from 40 C to max. 55 C is possible (taking the continuous current reductions listed into consideration), but results in a shorter lifespan. 6) Continuous operation of ACOPOS servo drives at altitudes ranging from 500 m to 2000 m above sea level is possible (taking the continuous current reductions listed into consideration). Additional requirements are to be arranged with B&R.

46

ACOPOS User's Manual V 1.3.1

Installation Dimension diagrams and installation dimensions

2.2 ACOPOS 1022, 1045, 1090

80 1)

Distance to next device 71 +0.5 0 70.5 35.25

Outgoing air

235.5

361

320

35

71.5

20

277 2 x fastening screws M5

80 1)

Incoming air

Figure 16: Dimensional diagram and installation dimensions for ACOPOS 1022, 1045, 1090
1) For proper air circulation, at least 80 mm has to be left free above and below the ACOPOS servo drive.

ACOPOS User's Manual V 1.3.1

109

Chapter 3 Installation

Wiring General Information

Chapter 5 Wiring
1. General Information
1.1 Electromagnetic Compatibility of the Installation
1.1.1 General Information If the guidelines for elecromagnetic compatibility of the installation are followed, ACOPOS servo drives meet EMC guidelines 89/336/EWG and low-voltage guidelines 73/23/EWG. They meet the requirements for harmonized EMC product standard IEC 61800-3:1996 + A11:2000 for industry (second environment). Additional EMC measures must be implemented by the manufacturer of machines or systems if the product standards for the machine has lower limits or if the machine should conform to generic standard IEC 61000-6-4. Additional EMC measures may also be needed for machines with a large number of ACOPOS servo drives. The installation of a central line filter is mostly sufficient in such cases. Proof of conformity to the necessary limits must be provided according to the documentation for use of the EMC guidelines from the manufacturer or distributor of the machine or system. Additional EMC measures are needed when operating ACOPOS servo drives in living area or when connecting ACOPOS servo drives to a low voltage system which supplies buildings in living areas without an intermediate transformer (first environment).

ACOPOS User's Manual V 1.3.1

147

Chapter 5 Wiring

Wiring General Information 1.1.2 Installation Notes 1) The switching cabinet or the system must be constructed appropriately. 2) To prevent the effects of disturbances, the following lines must be properly shielded: motor lines encoder cables control lines data cables

3) Inductive switching elements such as contactors or relays are to be equipped with corresponding suppressor elements such as varistors, RC elements or damping diodes. 4) All electrical connections are to be kept as short as possible. 5) Cable shields are to be attached to the designated shield terminals and the plug housing. 6) Shielded cables with copper mesh or tinned copper mesh are to be used. Twisting or extending the protective mesh using single conductors is not allowed. 7) Unused cable conductors are to be grounded on both sides if possible.

148

ACOPOS User's Manual V 1.3.1

Wiring General Information The ground connections and shield connections have to be made as illustrated in the following diagram.
Q1 L1 3 * 400 - 480 VAC L2 L3 50/60 Hz PE
1 3
2 4

2 3 1 4

PE

-DC1 +DC1 +DC2 -DC2

+24 V 0V +24 V

1 2 3

4 5 6 7 8

+24 V 0V

9 10 11 12 13

+24 V

14 15 16 17

0V

18

Trigger1 Quickstop/Trigger2 COM (1, 2) Shield Limit+ LimitRef Enable Enable X1 COM (8, 9) COM (8, 9) n.c. +24V out / 0.5A +24V +24V COM (5-7, 13-15) COM (5-7, 13-15) COM (5-7, 13-15)

X2

X3

ACOPOS

Slot 1

Slot 2

Slot 3

Slot 4
+DC

CAN, ETHERNET Powerlink

X4a
S3 S4 S1 S2

12...EnDat 6...Resolver

PE

L1 L2 L3

RB+ RB-

X4b
B+ BT+ T-

X5
PE

X6
PE
1

U V W

Chapter 5 Wiring

M
T

RB

Figure 32: Connection diagram for ground and shield connections

ACOPOS User's Manual V 1.3.1

149

Wiring General Information

The protective ground conductors (PE) for the power mains, the motor lines and external
braking resistor connection are internally connected with the housing of the ACOPOS servo drive.

The second protective ground conductor connection is required because of the increased
discharge current (> 3.5 mA) on ACOPOS servo drives 1022, 1045, 1090, 1180 and 1320. The same cross section as the power mains protective ground conductor must be used.

Both trigger inputs are only filtered internally with approx. 50 s. Make sure the cable shield
is grounded properly.

The cable shield must be attached to the shield connector. On all plug-in modules, the two screws used to fasten the module must be tightened so that
the mounting bracket is connected to ground.

Cable connection via DSUB plug:

The cable shield must be connected using the designated clamp in the metallic or metal plated plug housing. The fastening screws must be tightened. Cable connection via terminals: The cable shield must be attached to the shield connection terminal. Cable connection via RJ45 plug: Also grounding the cable shield provides an improvement in EMC properties. Grounding should take place on both sides, extensively and near to the connector.

Figure 33: Cable shield grounding for the ETHERNET Powerlink cable

150

ACOPOS User's Manual V 1.3.1

Wiring General Information

The cable shield for the motor line or the connection cable for the external braking resistor is
connected with the housing of the ACOPOS servo drive via the grounding plate using the grounding clamp provided:
Shield connection for the motor cable using grounding clamps ACOPOS 1010, 1016 ACOPOS 1022, 1045, 1090

ACOPOS 1180, 1320

ACOPOS 1640, 128M

Table 73: Grounding of the motor cable on the ACOPOS servo drive

On the motor side, the cable shield for the motor line is connected to the motor housing using
the motor plug and connected to ground via the machine. The cable shield on the connection cable for the external braking resistor must be connected with the housing of the braking resistor.

On the motor side, the encoder cable shield is connected to the motor housing using the
encoder plug and connected to ground via the machine.

ACOPOS User's Manual V 1.3.1

151

Chapter 5 Wiring

Wiring Plug-in Module Pin Assignments

1.2 Connecting Cables to Plug-in Modules

Figure 34: Connecting Cables to Plug-in Modules

Stress relief for the cable is implemented using a cable tie. The cable tie is to be run through the eye on the bottom of the plug-in module. Make sure that the ventilation slots on the bottom of the ACOPOS drive are not blocked.

152

ACOPOS User's Manual V 1.3.1

Wiring Overview of the Terminal Cross Sections

1.4 Overview of the Terminal Cross Sections 1)

8V1010.00-2 8V1010.50-2 8V1016.00-2 8V1016.50-2 [mm] 0.5 - 1.5 0.5 - 1.5 0.5 - 1.5 ----[AWG] 20 - 14 20 - 14 20 - 14 26 - 14 26 - 14 8V1022.00-2 8V1045.00-2 8V1090.00-2 [mm] 0.5 - 1.5 0.5 - 1.5 0.5 - 1.5 ----[AWG] 20 - 14 20 - 14 20 - 14 26 - 14 26 - 14 8V1180.00-2 8V1320.00-2 8V1640.00-2 8V128M.00-2

Connector

Wire Types Approbation Data Solid core / multiple conductor lines Flexible and fine wire lines without Wire Tip Sleeves with Wire Tip Sleeves Approbation Data UL/C-UL-US CSA

[mm] 0.5 - 1.5 0.5 - 1.5 0.5 - 1.5 -----

[AWG] 20 - 14 20 - 14 20 - 14 26 - 14 26 - 14

[mm] 0.5 - 1.5 0.5 - 1.5 0.5 - 1.5 -----

[AWG] 20 - 14 20 - 14 20 - 14 26 - 14 26 - 14

[mm] 0.5 - 1.5 0.5 - 1.5 0.5 - 1.5 -----

[AWG] 20 - 14 20 - 14 20 - 14 26 - 14 26 - 14

X1

Holding Torque for the Terminal Screws [Nm] Solid core / multiple conductor lines X2 DC Bus Flexible and fine wire lines without Wire Tip Sleeves with Wire Tip Sleeves Approbation Data UL/C-UL-US CSA

0.2 ... 0.25 0.2 - 4 0.2 - 4 0.25 - 4 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10 0.5 ... 0.6 0.2 - 4 0.2 - 4 0.25 - 4 ----0.2 - 2.5 0.2 - 2.5 0.25 - 2.5 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10 0.5 ... 0.6 24 - 12 24 - 12 23 - 12 30 - 12 28 - 12 0.5 ... 0.6 0.2 - 4 0.2 - 4 0.25 - 4 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10 0.5 ... 0.6 -----------------------

0.2 ... 0.25 0.2 - 4 0.2 - 4 0.25 - 4 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10 0.5 ... 0.6 0.2 - 4 0.2 - 4 0.25 - 4 ----0.2 - 2.5 0.2 - 2.5 0.25 - 2.5 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10 0.5 ... 0.6 24 - 12 24 - 12 23 - 12 30 - 12 28 - 12 0.5 ... 0.6 0.2 - 4 0.2 - 4 0.25 - 4 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10 0.5 ... 0.6 -----------------------

0.2 ... 0.25 0.5 - 10 0.5 - 6 0.5 - 6 ----20 - 7 20 - 9 20 - 9 20 - 8 20 - 8

0.2 ... 0.25 10 - 50 10 - 35 10 - 35 ----3 ... 4 10 - 50 10 - 35 10 - 35 ----3 ... 4 0.2 - 2.5 0.2 - 2.5 0.25 - 2.5 ----24 - 12 24 - 12 23 - 12 30 - 12 28 - 12 0.5 ... 0.6 10 - 50 10 - 35 10 - 35 ----3 ... 4 0.5 - 10 0.5 - 6 0.5 - 6 ----20 - 7 20 - 9 20 - 9 20 - 8 20 - 8 1.2 ... 1.5 7-0 7-2 7-2 10 - 2 12 - 2 7-0 7-2 7-2 10 - 2 12 - 2 7-0 7-2 7-2 10 - 2 12 - 2

0.2 ... 0.25 16 - 95 10 - 70 10 - 70 ----6 - 3/0 7 - 2/0 7 - 2/0 6 - 2/0 6 - 2/0 6 ... 10 16 - 95 10 - 70 10 - 70 ----0.2 - 2.5 0.2 - 2.5 0.25 - 2.5 ----6 - 3/0 7 - 2/0 7 - 2/0 6 - 2/0 6 - 2/0 6 ... 10 24 - 12 24 - 12 23 - 12 30 - 12 28 - 12 0.5 ... 0.6 16 - 95 10 - 70 10 - 70 ----6 - 3/0 7 - 2/0 7 - 2/0 6 - 2/0 6 - 2/0 6 ... 10 0.5 - 10 0.5 - 6 0.5 - 6 ----20 - 7 20 - 9 20 - 9 20 - 8 20 - 8 1.2 ... 1.5

Holding Torque for the Terminal Screws [Nm] Solid core / multiple conductor lines X3 Power mains Flexible and fine wire lines without Wire Tip Sleeves with Wire Tip Sleeves Approbation Data UL/C-UL-US CSA Solid core / multiple conductor lines Flexible and fine wire lines without Wire Tip Sleeves with Wire Tip Sleeves Approbation Data UL/C-UL-US CSA

1.2 ... 1.5 0.5 - 10 0.5 - 6 0.5 - 6 ----0.2 - 2.5 0.2 - 2.5 0.25 - 2.5 ----20 - 7 20 - 9 20 - 9 20 - 8 20 - 8 24 - 12 24 - 12 23 - 12 30 - 12 28 - 12

Holding Torque for the Terminal Screws [Nm] X4a, X4b Motor (holding brake, temperature sensor)

1.2 ... 1.5

Holding Torque for the Terminal Screws [Nm] Solid core / multiple conductor lines X5 Motor (power) Flexible and fine wire lines without Wire Tip Sleeves with Wire Tip Sleeves Approbation Data UL/C-UL-US CSA

0.5 ... 0.6 0.5 - 10 0.5 - 6 0.5 - 6 ----20 - 7 20 - 9 20 - 9 20 - 8 20 - 8

Holding Torque for the Terminal Screws [Nm] Solid core / multiple conductor lines X6 External braking resistor Flexible and fine wire lines without Wire Tip Sleeves with Wire Tip Sleeves Approbation Data UL/C-UL-US CSA

1.2 ... 1.5 0.2 - 4 0.2 - 4 0.25 - 4 ----24 - 10 24 - 10 23 - 10 30 - 10 28 - 10

Holding Torque for the Terminal Screws [Nm]

0.5 ... 0.6

Table 74: Terminal cross sections for ACOPOS servo drives

1) ACOPOS 1022/1045/1090 revision I0 and up; ACOPOS 1180/1320 revision F0 and up; ACOPOS 1640 revision K0 and up; ACOPOS 128M revision C0 and up.

ACOPOS User's Manual V 1.3.1

165

Chapter 5 Wiring

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

3. Pin Assignments ACOPOS 1022, 1045, 1090 1)

Figure 42: Pin assignment overview ACOPOS 1022, 1045, 1090

1) Starting with revision I0.

174

ACOPOS User's Manual V 1.3.1

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

3.1 Pin Assignments for Plug X1

X1 Pin 1 2 3 4 5 6
1

Description Trigger1 Quickstop/Trigger2 COM (1, 2) Shield Limit+ LimitRef Enable Enable COM (8, 9) COM (8, 9) ----+24V +24V COM (5-7, 14, 15) COM (5-7, 14, 15) COM (5-7, 14, 15)

Function Trigger 1 Quickstop/Trigger 2 Trigger 1, Quickstop/Trigger 2 - 0 V Shielding Positive HW limit Negative HW limit Reference switch Enable Enable Enable 0 V Enable 0 V ----Supply +24 V Supply +24 V Supply 0 V Supply 0 V Supply 0 V

7 8 9 10 11 12 13 14 15 16 17 18

X2

Pin 1 2 3 4

Description -DC1 +DC1 +DC2 -DC2

Function U DC bus U DC bus + U DC bus + U DC bus -

DC2

DC2

DC1

DC1

Terminal Cross Sections see table 74 "Terminal cross sections for ACOPOS servo drives" on page 165.

Table 86: Pin assignments for plug X2 ACOPOS 1022, 1045, 1090

ACOPOS User's Manual V 1.3.1

175

Chapter 5 Wiring

3.2 Pin Assignments for Plug X2

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

The following connections are linked with each other internally in the device: Pin 8 --> Pin 9 (Enable) Pin 10 --> Pin 11 (Enable 0 V) Pin 14 --> Pin 15 (Supply +24 V) Pin 16 --> Pin 17 --> Pin 18 (Supply 0 V)

Terminal Cross Sections see table 74 "Terminal cross sections for ACOPOS servo drives" on page 165.

Table 85: Pin assignments for plug X1 ACOPOS 1022, 1045, 1090

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

3.3 Pin Assignments for Plug X3

X3 Pin 1 2 3 4 Description L1 L2 L3 PE Function Power mains connection L1 Power mains connection L2 Power mains connection L3 Protective ground conductor

L3

L2

L1

Terminal Cross Sections see table 74 "Terminal cross sections for ACOPOS servo drives" on page 165.

Table 87: Pin assignments for plug X3 ACOPOS 1022, 1045, 1090

3.4 Pin Assignments for Plugs X4a, X4b

X4a Pin 1 2 3 4
S3 S4 S1 S2

Description S2 S1 S4 S3

Function Activation, supply for the external holding brake (+) Activation for the external holding brake (+) Activation, supply for the external holding brake (-) Activation for the external holding brake (-)

Terminal Cross Sections see table 74 "Terminal cross sections for ACOPOS servo drives" on page 165.

Table 88: Pin assignments for plug X4a ACOPOS 1022, 1045, 1090
X4b Pin 1 2 3 4 Description TT+ BB+ Function Temperature Sensor Temperature Sensor + Brake Brake +

B+

B-

T+

T-

Terminal Cross Sections see table 74 "Terminal cross sections for ACOPOS servo drives" on page 165.

Table 89: Pin assignments for plug X4b ACOPOS 1022, 1045, 1090

3.4.1 Wiring the Output for the Motor Holding Brake The supply, activation and monitoring of the output for the motor holding brake can take place via the the X4a connector in three different ways:

176

ACOPOS User's Manual V 1.3.1

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

Image 1
Monitoring

Description
+24 V

1
I
+ -

Supply: Internally by the ACOPOS servo drive

Ref

Activation: Internally by the ACOPOS servo drive

U
+ -

Ref

B+ BT+ T-

Monitoring: Internally by the ACOPOS servo drive

S3 S4 S1 S2

X4a

X4b
A jumper must be placed between S1 and S2 as well as S3 and S4 on the X4a connector. 1)

2
Monitoring

+24 V

1
I
+ -

Supply: Internally by the ACOPOS servo drive Activation: Internally by the ACOPOS servo drive and also possible externally using potential free contacts 2) Monitoring: Internally by the ACOPOS servo drive

Ref

+ -

Ref

S3 S4 S1 S2

B+ BT+ T-

X4a

X4b

Information:
T

The parameters for ACOPOS internal monitoring must be set according to the requirements of the application. 3)

3
Monitoring

+24 V

1
I
+ -

Supply: External
Ref

Activation: External Monitoring: External

B+ BT+ T-

+ -

Ref

S3 S4 S1 S2

X4a

X4b

Information:
T

ACOPOS internal monitoring cannot be used here; therefore it must be deactivated using software. 4)

0V

+24 V

Table 90: Activation for the external holding brake

1) Both jumpers are already on the X4a connector delivered with the ACOPOS servo drives. 2) External potential free contacts can be connected between S1 and S2 as well as between S3 and S4. This makes it possible to activate the holding brake using an external safety circuit independent of the control integrated in the ACOPOS servo drive. 3) The parameters are set using ParID 90 (1 ... internal monitoring active; 5 ... internal monitoring not active). 4) Deactivation takes place using ParID 90 (5 ... internal monitoring not active).

ACOPOS User's Manual V 1.3.1

177

Chapter 5 Wiring

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

3.5 Pin Assignments for Plug X5

X5 Pin 1 2 3 4 Description PE W V U Function Protective ground conductor Motor connection W Motor connection V Motor connection U

Terminal Cross Sections see table 74 "Terminal cross sections for ACOPOS servo drives" on page 165.

Table 91: Pin assignments for plug X5 ACOPOS 1022, 1045, 1090

3.6 Protective Ground Connection (PE)

The protective ground conductor is connected to the threaded bolt M5 provided using a cable lug. For information concerning dimensioning see section 1.1.3 "Protective Ground Connection (PE)" on page 122.
Image Pin --Description PE Function Protective ground conductor

Terminal Cross Sections Cable lug for threaded bolt M5

[mm] 0.25 - 16

AWG 23 - 5

Table 92: Protective ground conductor (PE) ACOPOS 1022, 1045, 1090

Danger!
Before turning on the servo drive, make sure that the housing is properly connected to ground (PE rail). The ground connection must be made, even when testing the servo drive or when operating it for a short time!

178

ACOPOS User's Manual V 1.3.1

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

3.7 Input/Output Circuit Diagram

X1
Trigger1 Quickstop/Trigger2 COM (1, 2) Shield
1 2 3 4

2K2

Trigger1
1n 38V

2K2

Trigger2
1n 38V

38V

X1
Limit+ LimitRef
5 6 7

6K6

Limit+
1n 38V

6K6

Limit1n 38V

X1
COM (5-7, 13-15) COM (5-7, 13-15) COM (5-7, 13-15)
16 17 18

6K6

Ref
1n 38V

38V

X1
Enable Enable COM (8, 9) COM (8, 9)
8 9 10 11

6E6

Enable
1n 38V

n.c. n.c. COM (5-7, 13-15) COM (5-7, 13-15) COM (5-7, 13-15)

12 13

1n
16 17 18

38V

Figure 43: Input/Output Circuit Diagram ACOPOS 1022, 1045, 1090

ACOPOS User's Manual V 1.3.1

179

Chapter 5 Wiring

X1

Wiring Pin Assignments ACOPOS 1022, 1045, 1090

+5V 15V

Brake control activate

X1
+24V +24V COM (5-7, 13-15) COM (5-7, 13-15) COM (5-7, 13-15)
14 15

38V

38V
16 17 18

COM
38V

+ Ref COM Ref

31V

X4a
1 2 3 4

Holding brake monitoring

1 I +

X2
-DC1 +DC1 +DC2 -DC2
1
2

S2 S1 S4 S3

RShunt RSym
COM Temperatue sensor evaluation

X4b
4 3 2 1

3
4

RSym

B+ BT+ T-

Loading relay

X3
L1 L2 L3
PE
1 2 3 4

X5
RB
4 3 2 1

U V W PE

Rectifier

Loading circuit and braking resistor control

IGBT output stage

Figure 43: Input/Output Circuit Diagram ACOPOS 1022, 1045, 1090 (Forts.)

180

ACOPOS User's Manual V 1.3.1