CCNPv6 ROUTE

Chapter 8 Lab 8-4, IPv6 Challenge Lab Instructor Version

Topology

Objectives

Implement the topology diagram using the instructions in the Requirements section.

Change the IPv6 IGP from OSPFv3 to RIPng.

Background
In the first part of this lab (Steps 1 through 7), you configure IPv4 with EIGRP on routers R1, R2 and R3. You
also configure IPv6 with OSPFv3 on routers R1, R3 and R4, create an IPv6 tunnel between R1 and R3 and
then test network connectivity. In the second part of the lab (Step 8), you replace the OSPFv3 routing protocol
with RIPng and re-test connectivity.

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 1 of 16

CCNPv6 ROUTE

Required Resources
Note: This lab uses Cisco 1841 routers with Cisco IOS Release 12.4(24)T1 and the Advanced IP Services
image c1841-advipservicesk9-mz.124-24.T1.bin. You can use other routers (such as a 2801 or 2811) and
Cisco IOS Software versions if they have comparable capabilities and features. Depending on the router
model and Cisco IOS Software version, the commands available and output produced might vary from what is
shown in this lab.

4 routers (Cisco 1841 with Cisco IOS Release 12.4(24)T1 Advanced IP Services or comparable)

Serial and console cables

Requirements
1. Configure all interfaces in the topology diagram with the IPv4 or IPv6 addresses shown.
2. Use EUI-64 addresses on the link between R3 and R4.
3. Configure EIGRP AS 1 on R1, R2, and R3 to route all IPv4 networks.
4. Disable EIGRP automatic summarization.
5. Configure a manual IPv6 tunnel between R1 and R3.
6. Include all IPv6 networks in OSPF area 0 on R1, R3, and R4.
7. Manually configure a router ID of 172.16.4.1 on R4 (this address does not need to be reachable).
8. Remove the OSPFv3 configuration commands from R1, R3, and R4 and configure RIPng to run on
these routers using RIP1 as the process name.

Notes: ______________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 2 of 16

CCNPv6 ROUTE
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 3 of 16

CCNPv6 ROUTE

Router Interface Summary Table

Router Model

Router Interface Summary

Ethernet Interface
Ethernet Interface
Serial Interface
#1
#2
#1

Serial Interface
#2

1700

Fast Ethernet 0
(FA0)

Fast Ethernet 1
(FA1)

Serial 0 (S0)

Serial 1 (S1)

1800

Fast Ethernet 0/0

(FA0/0)

Fast Ethernet 0/1

(FA0/1)

Serial 0/0/0
(S0/0/0)

Serial 0/0/1
(S0/0/1)

2600

Fast Ethernet 0/0

(FA0/0)

Fast Ethernet 0/1

(FA0/1)

Serial 0/0 (S0/0)

Serial 0/1 (S0/1)

2800

Fast Ethernet 0/0

(FA0/0)

Fast Ethernet 0/1

(FA0/1)

Serial 0/0/0
(S0/0/0)

Serial 0/0/1
(S0/0/1)

Note: To find out how the router is configured, look at the interfaces to identify the type of router
and how many interfaces the router has. Rather than list all combinations of configurations for each
router class, this table includes identifiers for the possible combinations of Ethernet and serial
interfaces in the device. The table does not include any other type of interface, even though a
specific router might contain one. For example, for an ISDN BRI interface, the string in parenthesis
is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 4 of 16

CCNPv6 ROUTE

IPv6 Challenge Lab - Answer Key (Instructor version)

Note: EIGRP and OSPFv3 are configured and tested in Part 1. In Part 2, OSPFv3 is replaced by RIPng.

Part 1 IPv6 with EIGRP and OSPFv3

The R1 IPv4 and IPv6 routing tables are shown here.
R1# show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set

D
C

172.16.0.0/24 is subnetted, 2 subnets

172.16.23.0 [90/41024000] via 172.16.12.2, 00:02:30, Serial0/0/0
172.16.12.0 is directly connected, Serial0/0/0

R1# show ipv6 route

IPv6 Routing Table - Default - 8 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C
FEC0::1:0/112 [0/0]
via Loopback0, directly connected
L
FEC0::1:1/128 [0/0]
via Loopback0, receive
O
FEC0::3:1/128 [110/1000]
via FE80::AC10:1703, Tunnel0
O
FEC0::4:1/128 [110/2562]
via FE80::AC10:1703, Tunnel0
C
FEC0::13:0/112 [0/0]
via Tunnel0, directly connected
L
FEC0::13:1/128 [0/0]
via Tunnel0, receive
O
FEC0:34::/64 [110/2562]
via FE80::AC10:1703, Tunnel0
L
FF00::/8 [0/0]
via Null0, receive

Tcl Results
Note: You will need to substitute the R3 and R4 serial interface EUI-64 addresses in the Tcl script because
they vary for every router. To obtain these addresses, use the show ipv6 interface interface command on
routers R3 and R4.
tclsh
foreach address {
172.16.12.1
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 5 of 16

CCNPv6 ROUTE
172.16.12.2
172.16.23.2
172.16.23.3
FEC0::1:1
FEC0::3:1
FEC0::4:1
FEC0::13:1
FEC0::13:3
<R3s S0/1/0 EUI-64 address>
<R4s S0/0/0 EUI-64 address>
} {
ping $address }
R1# tclsh
R1(tcl)#foreach address {
+>(tcl)#172.16.12.1
+>(tcl)#172.16.12.2
+>(tcl)#172.16.23.2
+>(tcl)#172.16.23.3
+>(tcl)#FEC0::1:1
+>(tcl)#FEC0::3:1
+>(tcl)#FEC0::4:1
+>(tcl)#FEC0::13:1
+>(tcl)#FEC0::13:3
+>(tcl)#FEC0:34::21A:2FFF:FEC6:91D0
+>(tcl)#FEC0:34::21A:2FFF:FE7E:9648
+>(tcl)#} {
+>(tcl)#ping $address }
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.1, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.2, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.2, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.3, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::1:1, timeout is 2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::3:1, timeout is 2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::4:1, timeout is 2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.

2 seconds:
= 56/58/68 ms
2 seconds:
= 28/28/32 ms
2 seconds:
= 28/28/32 ms
2 seconds:
= 56/56/56 ms
seconds:
= 0/0/0 ms
seconds:
= 64/65/68 ms
seconds:
= 92/94/96 ms

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 6 of 16

CCNPv6 ROUTE
Sending 5, 100-byte ICMP Echos to FEC0::13:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::13:3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/65/68 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21A:2FFF:FEC6:91D0, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/64/68 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21A:2FFF:FE7E:9648, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 96/96/96 ms
R1(tcl)#tclquit
R2#tclsh
R2(tcl)#foreach address {
+>(tcl)#172.16.12.1
+>(tcl)#172.16.12.2
+>(tcl)#172.16.23.2
+>(tcl)#172.16.23.3
+>(tcl)#FEC0::1:1
+>(tcl)#FEC0::3:1
+>(tcl)#FEC0::4:1
+>(tcl)#FEC0::13:1
+>(tcl)#FEC0::13:3
+>(tcl)#FEC0:34::21A:2FFF:FEC6:91D0
+>(tcl)#FEC0:34::21A:2FFF:FE7E:9648
+>(tcl)#} {
+>(tcl)#ping $address }
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.1, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.2, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.2, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.3, timeout is
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max
Unrecognized host or address, or protocol not running.
% Unrecognized host or address, or protocol not running.
% Unrecognized host or address, or protocol not running.
% Unrecognized host or address, or protocol not running.
% Unrecognized host or address, or protocol not running.
% Unrecognized host or address, or protocol not running.
% Unrecognized host or address, or protocol not running.

2 seconds:
= 28/31/40 ms
2 seconds:
= 56/64/72 ms
2 seconds:
= 56/57/64 ms
2 seconds:
= 28/28/32 ms%

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 7 of 16

CCNPv6 ROUTE
R2(tcl)#tclquit
R3#tclsh
R3(tcl)#foreach address {
+>(tcl)#172.16.12.1
+>(tcl)#172.16.12.2
+>(tcl)#172.16.23.2
+>(tcl)#172.16.23.3
+>(tcl)#FEC0::1:1
+>(tcl)#FEC0::3:1
+>(tcl)#FEC0::4:1
+>(tcl)#FEC0::13:1
+>(tcl)#FEC0::13:3
+>(tcl)#FEC0:34::21A:2FFF:FEC6:91D0
+>(tcl)#FEC0:34::21A:2FFF:FE7E:9648
+>(tcl)#} {
+>(tcl)#ping $address }
Translating "172.16.12.1"
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/56 ms
Translating "172.16.12.2"
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms
Translating "172.16.23.2"
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms
Translating "172.16.23.3"
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/58/68
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::1:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/67/68
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::3:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/4 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::4:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::13:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 68/68/68
Type escape sequence to abort.
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

ms

ms

ms

ms

Page 8 of 16

CCNPv6 ROUTE
Sending 5, 100-byte ICMP Echos to FEC0::13:3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/4 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21A:2FFF:FEC6:91D0, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21A:2FFF:FE7E:9648, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms
R3(tcl)#tclquit
R4#tclsh
R4(tcl)#foreach address {
+>(tcl)#172.16.12.1
+>(tcl)#172.16.12.2
+>(tcl)#172.16.23.2
+>(tcl)#172.16.23.3
+>(tcl)#FEC0::1:1
+>(tcl)#FEC0::3:1
+>(tcl)#FEC0::4:1
+>(tcl)#FEC0::13:1
+>(tcl)#FEC0::13:3
+>(tcl)#FEC0:34::21A:2FFF:FEC6:91D0
+>(tcl)#FEC0:34::21A:2FFF:FE7E:9648
+>(tcl)#} {
+>(tcl)#ping $address }
Translating "172.16.12.1"
% Unrecognized host or address, or protocol not running.
Translating "172.16.12.2"
% Unrecognized host or address, or protocol not running.
Translating "172.16.23.2"
% Unrecognized host or address, or protocol not running.
Translating "172.16.23.3"
% Unrecognized host or address, or protocol not running.
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::1:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 92/92/92 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::3:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::4:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::13:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 96/96/96 ms
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 9 of 16

CCNPv6 ROUTE
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::13:3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21A:2FFF:FEC6:91D0, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21A:2FFF:FE7E:9648, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms
R4(tcl)#tclquit

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 10 of 16

CCNPv6 ROUTE

Device Configurations Part 1 (EIGRP and OSPFv3)

Router R1
hostname R1
!
ipv6 unicast-routing
!
interface Tunnel0
ipv6 address FEC0::13:1/112
ipv6 ospf 1 area 0
tunnel source Serial0/0/0
tunnel destination 172.16.23.3
tunnel mode ipv6ip
!
interface Loopback0
ipv6 address FEC0::1:1/112
ipv6 ospf 1 area 0
!
interface Serial0/0/0
ip address 172.16.12.1 255.255.255.0
clock rate 64000
bandwidth 64
no shutdown
!
router eigrp 1
network 172.16.0.0
no auto-summary
!
ipv6 router ospf 1
!
end

Router R2
hostname R2
!
interface Serial0/0/0
ip address 172.16.12.2 255.255.255.0
bandwidth 64
no shutdown
!
interface Serial0/0/1
ip address 172.16.23.2 255.255.255.0
clock rate 64000
bandwidth 64
no shutdown
!
router eigrp 1
network 172.16.0.0
no auto-summary
!
end

Router R3
hostname R3
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 11 of 16

CCNPv6 ROUTE
!
ipv6 unicast-routing
!
interface Loopback0
ipv6 address FEC0::3:1/112
ipv6 ospf 1 area 0
!
interface Tunnel0
ipv6 address FEC0::13:3/112
ipv6 ospf 1 area 0
tunnel source Serial0/0/1
tunnel destination 172.16.12.1
tunnel mode ipv6ip
!
interface Serial0/0/1
ip address 172.16.23.3 255.255.255.0
bandwidth 64
no shutdown
!
interface Serial0/1/0
ipv6 address FEC0:34::/64 eui-64
ipv6 ospf 1 area 0
clock rate 64000
bandwidth 64
no shutdown
!
router eigrp 1
network 172.16.0.0
no auto-summary
!
ipv6 router ospf 1
!
end

Router R4
hostname R4
!
ipv6 unicast-routing
!
interface Loopback0
ipv6 address FEC0::4:1/112
ipv6 ospf 1 area 0
!
interface Serial0/0/0
ipv6 address FEC0:34::/64 eui-64
ipv6 ospf 1 area 0
bandwidth 64
no shutdown
!
ipv6 router ospf 1
router-id 172.16.4.1
!
end

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 12 of 16

CCNPv6 ROUTE

Part 2 IPv6 with EIGRP and RIPng

The R1 IPv4 and IPv6 routing tables and Tcl results are shown here.
R1# show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set

D
C

172.16.0.0/24 is subnetted, 2 subnets

172.16.23.0 [90/41024000] via 172.16.12.2, 00:02:30, Serial0/0/0
172.16.12.0 is directly connected, Serial0/0/0

R1# show ipv6 route

IPv6 Routing Table - Default - 8 entries
Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
EX - EIGRP external
O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C
FEC0::1:0/112 [0/0]
via Loopback0, directly connected
L
FEC0::1:1/128 [0/0]
via Loopback0, receive
R
FEC0::3:0/112 [120/2]
via FE80::AC10:1703, Tunnel0
R
FEC0::4:0/112 [120/3]
via FE80::AC10:1703, Tunnel0
C
FEC0::13:0/112 [0/0]
via Tunnel0, directly connected
L
FEC0::13:1/128 [0/0]
via Tunnel0, receive
R
FEC0:34::/64 [120/2]
via FE80::AC10:1703, Tunnel0
L
FF00::/8 [0/0]
via Null0, receive
R1# tclsh
R1(tcl)#foreach address {
+>(tcl)#172.16.12.1
+>(tcl)#172.16.12.2
+>(tcl)#172.16.23.2
+>(tcl)#172.16.23.3
+>(tcl)#FEC0::1:1
+>(tcl)#FEC0::3:1
+>(tcl)#FEC0::4:1
+>(tcl)#FEC0::13:1
+>(tcl)#FEC0::13:3
+>(tcl)#FEC0:34::21B:53FF:FE0D:6028
+>(tcl)#FEC0:34::21B:53FF:FE24:AA72
+>(tcl)#} {
+>(tcl)# ping $address }
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 13 of 16

CCNPv6 ROUTE

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.16.12.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/56 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.12.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/32 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.23.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/56/56 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::1:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/4 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::3:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/66/68 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::4:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 92/93/96 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::13:1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/0 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0::13:3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 64/66/68 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21B:53FF:FE0D:6028, timeout is 2 seco
nds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 68/68/68 ms
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to FEC0:34::21B:53FF:FE24:AA72, timeout is 2 seco
nds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 92/94/96 ms

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 14 of 16

CCNPv6 ROUTE

Device Configurations Part 2 (EIGRP and RIPng)

Router R1
hostname R1
!
ipv6 unicast-routing
!
interface Tunnel0
ipv6 address FEC0::13:1/112
ipv6 rip RIP1 enable
tunnel source Serial0/0/0
tunnel destination 172.16.23.3
tunnel mode ipv6ip
!
interface Loopback0
ipv6 address FEC0::1:1/112
ipv6 rip RIP1 enable
!
interface Serial0/0/0
ip address 172.16.12.1 255.255.255.0
clock rate 64000
bandwidth 64
no shutdown
!
router eigrp 1
network 172.16.0.0
no auto-summary
!
ipv6 router rip RIP1
!
end

Router R2
hostname R2
!
interface Serial0/0/0
ip address 172.16.12.2 255.255.255.0
bandwidth 64
no shutdown
!
interface Serial0/0/1
ip address 172.16.23.2 255.255.255.0
clock rate 64000
bandwidth 64
no shutdown
!
router eigrp 1
network 172.16.0.0
no auto-summary
end

Router R3
hostname R3
!
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 15 of 16

CCNPv6 ROUTE
ipv6 unicast-routing
!
interface Loopback0
ipv6 address FEC0::3:1/112
ipv6 rip RIP1 enable
!
interface Tunnel0
ipv6 address FEC0::13:3/112
ipv6 rip RIP1 enable
tunnel source Serial0/0/1
tunnel destination 172.16.12.1
tunnel mode ipv6ip
!
interface Serial0/0/1
ip address 172.16.23.3 255.255.255.0
bandwidth 64
no shutdown
!
interface Serial0/1/0
ipv6 address FEC0:34::/64 eui-64
ipv6 rip RIP1 enable
clock rate 64000
bandwidth 64
no shutdown
!
router eigrp 1
network 172.16.0.0
no auto-summary
!
ipv6 router rip RIP1
!
end

Router R4
hostname R4
!
ipv6 unicast-routing
!
interface Loopback0
ipv6 address FEC0::4:1/112
ipv6 rip RIP1 enable
!
interface Serial0/0/0
ipv6 address FEC0:34::/64 eui-64
ipv6 rip RIP1 enable
bandwidth 64
no shutdown
!
ipv6 router rip RIP1
!
end

All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 16 of 16