HAND CHAIN HOIST

OPERATING, MAINTENANCE, & PARTS MANUAL

ACI Hoist & Crane 757 Southeast 17th Street Fort Lauderdale, Fl 33116 Phone: 954 -367-7116 Fax: 954-272-0334 www.ACIHoist.com

Table of Contents
SECTION 1 General Information 1.1 Hoist Construction 2 Safety Precautions 2.1 Terms & Summary 2.2 Safety Rules 2.3 Warning: To Avoid Injury: DOs & DONTs 3 Inspection before Initial Use 3.1 Installation 3.2 Testing 4 Technical Information 4.1 Specification 5 Handling the Load 5.1 Attaching the Load 5.2 Lifting the Load 6 Dimensions and Specification 6.1 Chain Hoist 6.2 Hook Dimensions 6.3 Reject Opening 7 Maintenance 7.1 Preventive Maintenance 7.2 Cautions 8 Inspections & Lubrications 8.1 Service & Frequency Information 8.2 Inspection Schedule 8.3 Disassembly 8.4 Lubrication 8.5 Lubrication Schedule 8.6 Recommended Lubricants 9 Spare Parts 9.1 - 20 Ton Exploded View 9.2 Parts List 10 Warranty PAGE 3 3 3-5 3 4 4-5 6 6 6 7 7 8 8 8 9 9 9 9 10 10 10 10-11 10 10 10 11 11 11 12-13 12 13 13

1.0: GENERAL INFORMATION

This document provides information and maintenance of ACI Hand Chain Hoist. People who are operating or maintaining the hoist should be familiar with this manual. Following the precautions, procedures and maintenance practices in this manual should ensure long and reliable operation. People responsible for the installation, operation, and/or maintenance of the equipment should be familiar with the American National Standard ANSI B30.16 for guidelines on the safe operation of hoists. That document contains rules on inspection requirements and records that may be required by some regulatory agencies. 1.1: HOIST CONSTRUCTION This hand chain hoist is an efficient means of lifting freely suspended material loads within its load rating. The frame and covers of the hoist are made from stamped steel construction. The cast hand chain wheel and load activated break will provide smooth, precise spotting of loads.

2.0: SAFETY PRECAUTIONS

2.1: TERMS & SUMMARY This manual provides important information for personnel involved with the installation, operation, and maintenance of the HOIST. Although you may be familiar with hoist or similar equipment, it is strongly recommended that you read this manual before installing, operating or maintaining the product. 2.1.1: DANGER, WARNING, CAUTION & NOTICE Throughout this manual, there are steps and procedures that can present hazardous situations. The following signals words are used to identify the degree or level of hazard seriousness. Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury and property damage.

DANGER WARNING CAUTION NOTICE

Warning indicates an imminently hazardous situation which, if not avoided, could result in death or serious injury and property damage.

Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or property damage.

Notice is used to notify people of installation, operation or maintenance information which is important but not directly hazard related

2.2: SAEFTY RULES Inspect the hoist for loose, broken or malfunctioning parts. Any hoist should be tagged out of order and taken out of service until the problem is corrected. DO NOT overload the hoist. DO NOT exert more than the hand chain pull to lift rated load by one operator (see Table 1). The hoist is designed to lift its rated capacity when a reasonable force is exerted. If effort appears to be excessive, recheck the load and use a larger capacity hoist if necessary. DO NOT side load the hoist. Make sure to pull in the straight line between hooks. Side loading the hoist over a sharp corner may fracture the hoist housing, load block or hook. Be sure there are NO twists in the chain. Make sure that the load chain is free to move and clear all obstructions. With multiple chained hoists the load hook can be turned one or more times causing the chain to twist. DO NOT use the hoist from an unbalanced/unstable position. Operators should have firm footing or be secured before operating the hoist. Before raising and/or pulling a load always make sure that the slings and other rigging have sufficient capacity to support the load, and are in good condition. DO NOT STAND BENEATH A LOAD! DO NOT operate a load in a way to endanger personnel. DO NOT leave the hoist with a suspended load. DO NOT wrap the load chain around the load. USE A SLING! DO NOT TIP-LOAD the hook, as this will exert undue strain, resulting in hook failure. The hoist is designed for manual operation by one person only. DO NOT use the hoist with and other power besides the manual power from one person.

DO NOT USE HOIST TO LIFT, SUPPORT OR OTHERWISE TRANSPORT PEOPLE.

The hand chain has a safety latch. When the safety latch opens or deforms, stop immediately to find out the cause. Hoists are designed to lift loads vertically and SHOULD NOT be used for horizontal or angle hoisting. NEVER use the chain or hook as a ground welding. Use only parts and chains supplied by the authorized distributor.

2.3: WARNING: TO AVOID INJURY: DOS & DONT These recommendations apply to all hand chain manually operated chain hoists for vertical lifting service involving material handling of freely suspended unguided loads. 1. DO read ANSI B30.16 Safety Standard for Overhead Hoists and Hoist and Manufacturers Operating, Maintenance and Instructions. 2. DO familiarize yourself with the operating control and procedures for the hoist. 3. DO make sure the suspension hook for the hoist is securely attached to an appropriate support. 4. DO establish firm footing or be otherwise secured when opening the hoist. 5. DO make sure that load slings or other approved attachments are sized properly and seated correctly in the hook saddle. 6. DO make sure the hook latch is closed and not supporting any part of the load. 7. DO make sure that load is free to move and will clear all obstacles. 8. DO make sure all persons stay clear of the suspended load. 9. DO avoid swinging of the load or load hook. 10. DO protect load chain from weld spatter or other damaging contaminants. 11. DO promptly report any malfunction, unusual performance, or damage of the hoist. 12. DO inspect hoist regularly, replace damaged or worn parts, and keep appropriate records of maintenance. 13. DO use the hoist manufacturers recommended part when repairing a hoist. 14. DO use the hook latches wherever possible. 15. DO apply lubricant to load chain as recommended by the hoist manufacturer.

16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37.

DO NOT lift more than rated load. DO NOT use the hoist load-limiting device to measure the load. DO NOT use damaged hoist or hoist that is not working correctly. DO NOT use hoist with twisted, kinked, damaged or worn chain. DO NOT Lift a load unless chain is properly seated in chain wheel(s) or sprockets(s). DO NOT use load chain as a sling or wrap load chain around the load. DO NOT lift a load if any binding prevents equal loading on all supporting chains. DO NOT apply the load to the tip of the hook. DO NOT operate unless load is centered under hoist. DO NOT operate hoist with other than manual power. DO NOT permit more than one operator to pull a single hand chain at one time. DO NOT allow your attention to be diverted from operating the hoist. DO NOT operate hoist beyond limits of load chain travel. DO NOT use hoist to lift, support, or transport people. DO NOT lift loads over people. DO NOT leave a suspended load unattended unless specific precautions have been taken. DO NOT allow sharp contact between two hoists or between hoist and obstructions. DO NOT allow the chain or hook to be used as a ground for welding. DO NOT allow the chain or hook to be touched by a live welding electrode. DO NOT remove or obscure the warnings on the hoist. DO NOT adjust or repair a hoist unless qualified to perform hoist maintenance. DO NOT attempt to lengthen the load chain or repair damaged load chain.

3.0: INSPECTION BEFORE INITIAL USE

After unpacking the hoist, inspect carefully for any damage that may have occurred during shipping. Check for loose, missing or damaged parts. 3.1: INSTALLATION Be sure that the supporting structures of the hoist are strong enough to support the full rated load of the hoist using a generous factor of safety. The hoist should be suspended directly above the load, so that it can be lifted without side pull. The hoist body must be free to align between the two hooks. Do not allow the hoist frame to rest against the supporting structure. Installation MUST be performed by a qualified person in accordance with ACI Hoist & Crane. Severe injury, death and/or property damage can result if the hoist is not correctly installed. For service in this area, please contact: ACI Hoist & Crane 757 S.E. 17th Street Fort Lauderdale, FL 33316 Phone: 954-367-6116 Fax: 954-272-0334 Toll Free: 1-866-424-6478 Make sure to check that the power supply to which the hoist is to be connected matches the information shown on the identification plate located on the bottom of the hoist. Before using the hoist, fill in the information below: Model No.: __________________________________ Serial No.: __________________________________ Purchase Date: ______________________________

3.2: TESTING Lift a light load with the hoist to check for a smooth operation and proper braking. If the hoist works properly with the light load, connect the rated load to the hoist and lift the load just clear of the floor. Check that the brake is holding the load before lifting it any higher. The hook shouldnt drift under any size loads that are within the hoists load rating.

4.0: TECHNICAL INFORMATION

4.1: SPECIFICATIONS PRODUCT CODE

HCH-010-10
TYPE:
HCH = HAND CHAIN HOIST

Amount of Lift

CAPACITY CODE:
010 = TON 020 = 1 TON 040 = 2 TON 060 = 3 TON 100 = 5 TON 200 = 10 TON 400 = 20 TON FEATURES Load Chain Hook Ease of Use Safety Durability Portability Braking = Heavy Duty, Heated-treated, wear-resistant load chain = Forged carbon steel hooks with safety latches. Under excessive loads, hook will open gradually and not fracture. Durable 360 rotating hook pivot. = Precise, durable gearing produces maximum lift, with minimal effort. = Clutch automatically slips when lifting loads beyond the rated weight capacity, preventing potential damage and/or injury. = Highly durable stamped steel construction = Lightweight, compact design for easy transport between work locations. = Automatic mechanical double-pawl braking system.

5.0: HANDLING THE LOAD

5.1: ATTACHING THE LOAD a. The load should be attached to the hook with slings or other appropriate devices. Do not wrap the load chain around a load. b. Be sure the load is supported in the saddle of the hook and the latch is closed. Do not lift a load on the tip of the hook.

5.2: LIFTING THE LOAD a. Raise the load by pulling the right side hand chain. Lift the load just clear of the floor. Check the sling is secure in the hook and the load is well balanced, and hoist brake is holding the load. Lift the load to the desired height, standing clear of the load. b. Lower the load by pulling the left side hand chain. Pull smoothly and slowly. Do not spin the hand chain. c. Do not jam the hook block into the bottom of the hoist, or run the hook down until the slack chain is pulled tight.

6.0: DIMENSIONS AND SPECIFICATION

- 3 Ton

5 Ton

10 Ton

20 Ton

6.1: CHAIN HOIST SPECIFICATION

Standard Lift (ft) Hand Chain Drop (ft)

Capacity (ton)

Model Number

No. of Chain Falls

A (in)

B (in)

C (in)

D (in)

H (in)

1/2 1 2 3 5 10 20

HCH-010 HCH-020 HCH-040 HCH-060 HCH-100 HCH-200 HCH-400 10 8

1 1 1 1 2 4 8

5.8 6.8 8.3 10.0 11.0 18.2 35.4

5.2 6.0 6.9 8.1 7.4 7.4 7.4

0.98 1.06 1.40 1.54 1.77 2.13 3.23

1.38 1.48 1.97 2.17 2.60 3.35 4.17

13.58 14.80 18.50 21.57 27.10 30.11 37.40

Note: Maximum lift allowed for all capacities is 40 ft.

6.2: HOOK DIMENSIONS (OPENING) Inspect the hooks for deformation, damage or cracks. If the hook is twisted more than 10 degrees from the plane of the unbent hook it should be replaced. Hooks damaged having a throat opening greater than the reject opening shown in table 2 must be replaced. 6.3: REJECT OPENING (Table 2) Capacity (ton) 1/2 1 2 3 5 10 20 Standard dimension (in) 0.98 1.06 1.40 1.54 1.77 2.13 3.15 Reject Opening (in) > 1.08 > 1.30 > 1.45 > 1.73 > 1.84 > 2.60 > 3.68

7.0: MAINTENANCE
7.1: PREVENTIVE MAINTENANCE It is important to provide periodic inspection and lubrication to enable lengthy and satisfactory operation of the hoist. Inspections are recommended at the intervals listed in Table 3 and are based on intermittent use. The operator should increase or decrease his inspection intervals based on usage and experience.

7.2: CAUTION If the chain is worn or otherwise damaged, replace entire chain with a new chain supplied by the hoist manufacturer. Do not substitute. Do not attempt to re-weld a damaged chain.

8.0: INSPECTIONS & LUBRICATIONS

8.1: SERVICE & FREQUENCY INFORMATION Service Information Normal Service Service which involves operating at less than a certain percentage of rated load and less than an unspecified frequency. Refer to the ANSI/ASME 30 volume for the specific definition of your application. Heavy Service Service which involves operation within the rated load limit which exceeds normal service. Severe Service Service which involves normal to heavy service with abnormal operating conditions. Frequent/Daily Inspections Frequent/Daily inspections are visual examinations by the operator or other designated personnel with interval per the following criteria. Normal Service Monthly Heavy Service Weekly to Monthly Severe Service Daily to Weekly Special or Infrequent Service As recommended by a qualified person before and after each occurrence. 8.2: INSPECTION SCHEDULE (Table 3) Interval Inspection a. Check the hooks and the hook latches for cracks or deformities. Twisted hooks or hooks with throat openings more than the reject openings listed in the above table should be replaced. b. Check chain for wear and twisting. c. Check brake for drift. a. Check for loose screws, nuts, etc. b. Check load sprocket and hand chain wheel for wear. a. Inspect for worn gears, pawl, spring, ratchet and shafts. b. Check for worn brake discs. c. Inspect chain in kerosene or other non-corrosive solvent and inspect for wear, nicks, or distortion of any kind.

DAILY

QUARTERLY

ANNUALLY

8.3: DISASSEMBLY Breaking down the hoist is straightforward. Make a note of the locations and orientations of the hoists different parts.

10

8.4: LUBRICATION a. Lubrication is essential to prolong chain life. Always lubricate load chain weekly or more frequently depending on severity of service. Be sure the lubricant reaches the bearing surfaces between the links. Remove the excess oil from the chain. The load chain should be kept well lubricated with chain lube. Be sure that the oil-lube is worked into the area between the links. b. If the hoist is disassembled for inspection or repair, re-lubricate the moving parts according to table 5.

8.5: LUBRICATION SCHEDULE (Table 4) PART Gears, bearings pawl pivot pin, guide roller pin and hook shanks Chain wheel treads Chain DESCRIPTION Check operation of the part FREQUENCY Annually

Check operation of the part Check operation of the part Lubricate chain, under normal usage Lubricate chain, under heavy usage require to be lubricated more frequently

Annually Quarterly Weekly

CAUTION
The brake surfaces must be kept free of any trace of oil or grease. Apply lubricant sparingly to the parts near the brake to avoid oil contamination of the brake.

8.6: RECOMMENDED LUBRICANTS (Table 5) PART Gears, bearings, pawl pivot pin, guide roller pin, hook shanks, and chain wheel treads Chain Brake parts, ratchet teeth LUBRICANT Any good quality gear grease Chain Lube Do Not Lubricate

11

9.0: SPARE PARTS

9.1: EXPLODED VIEW

12

9.2: PART LIST

1. Hand wheel cover assembly 2. Hand wheel 3. Brake cover 4. Friction plate 5. Ratchet disc 6. Brake seat 7. Lock plate 8. Top pin 9. Side plate assembly B 10. Chain sprocket 11. Side plate assembly A 12. Splined gear 13. Driven shaft assembly 14. Driving shaft 15. Gear case assembly 16. Name plate 17. Suspension plate 18. Stripper 19. Guide roller 20. Load chain 21. Pawl spring 22. Pawl 23. Hand chain 30. Top hook assembly 31. Double spring 32. Safety latch 33. Chain pin 34. Bottom hook assembly 35.Hook Hanger Component 35. Chain pin 36. Idle sheave assembly (5T) 37.Bottom Hook 37. Hook assembly 37. Hook Hanger Component 38. Beam assembly 40. Idle sheave pin 41. Idle sheave pin plate 42. Hook pin 52. Screw 53. Washer 60. Prevailing torque type nut 61. Split pin 62. Hexagonal castle nut 63. Screw 64. Spring washer 65. Snap Ring 66. Snap ring 67. Prevailing torque type nut 68. Screw 69. Snap ring 70. Prevailing torque type nut 71. Rivet 72. Split pin 73. Pin 74. Prevailing torque type nut 75. Hexagonal Bolt 90. Bearing A 91. Roller Bearing 92. Bearing B

10.0: WARRANTY

WARRANTY
Every hoist is thoroughly inspected and tested before it is shipped from the factory. If any problem develops within one-year return the complete hoist prepaid to the factory. If an inspection reveals that the problem is caused by defective workmanship or material, repairs will be made without charge and the hoist will be returned, transportation prepaid. This warranty does not cover: (a) deterioration caused by normal wear, abuse, eccentric or side loading, overloading, chemical or abrasive actions, improper maintenance or excessive heat; (b) problems resulting from repairs, modifications or alterations made by people other than factory or ACI representative; (c) the hoist has been abused or damaged due to an accident; (4) repair parts or accessories other than ACI equipment are used on the hoist. Equipment and accessories not of the sellers manufacture are warranted only to extent that they are warranted by the manufacturer. EXCEPT AS STATED HERE, ACI MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES FOR A PARTICULAR PURPOSE.

13