American Valve Series 7000 Butterfly Valves

P .O. Box 35229 Greensboro, NC 27425 1-800-645-0101 or (336) 668-0554 fax: 1-800-876-0109 or (336) 668-4070

Disc materials: Ni Coated Ductile Iron, Bronze, 316SS. Seatmaterials: Buna-N, EPDM, Viton & Specials. 10 Position Handle, Infinite Position and Gear Operators. Electric Motor Operators. Pneumatic Cylinder Operators. Galvanized Stem Extensions (Extended Bonnets). Chain Wheel Operators, Square Operating Nuts and Cranks. 100% Bi-directional factory tested. Extended neck design for ample application of insulation. One piece/uni-body construction to accommodate bothANSl and DlN flanges. Integral mounting flange will accept all styles of gear operators and actuators. Oil impregnated stem bushings assure long life even during extended periods of inactivity. One piece resilient seat with integral o-ring eliminates the need for additional flange gaskets. Integral o-ring seals for upper and lower valve shafts work with disc edge hub seals to provide a double stem seal. Two piece shaft design eliminates the need for bolts or pins to attach shaft to disc, thereby removing potential leak path of media. Two piece shaft design allows fora reduction in disc thickness thus creating less obstruction in waterway which results in lower Cv factors. Suitable for open left or open right operation. Field change over and field replaceable seats are standard design features. Tangential pin for mechanical stem retention standard.

American Valve Butterfly Valves are manufactured in accordance with the specifications from MSS SP67, Manufacturers Standardization Society and API609, American Petroleum Institute Latest Revisions. Both Lug and Wafer series valves are designed for ANSI Bl 16.5 125/150 Lb. class flanges and are rated at 200 PSI WOG service. American Series 7000 Butterfly Valves are 100% factory tested in both directions of operation to assure a Zero leakage rate for many years of BubbleTite service. American Series 7000 Butterfly Valves make an excellent choice by combining the balance of an economical valve with the performance required for Commerical, HVAC and Industrial applications. American Series 7000 Butterfly Valves are available with many options and accessories needed for the typical butterfly valve application.

LUG
Specifications: MSS SP-67 API-609 Rating 200 WOG
P .O. Box 35229 Greensboro, NC 27425 1-800-645-0101 or (336) 668-0554 fax: 1-800-876-0109 or (336) 668-4070

Stem Disc 7000L Nl Plated Ductile 416SS 7001L Nl Plated Ductile 41 6SS 416SS Bronze 7100L 416SS Bronze 7101L 316SS 316SS 7210L 316SS 316SS 7211L

Seat Material Buna N EPDM Buna N EPDM Buna N EPDM

Body Style Lug Lug Lug Lug Lug Lug

Dimension Table (inches)

SIZE A B C D F G H J L *M THREAD **N P Q 2 1/2 2 9 3/8 10 3/16 5 3/8 5 15/16 3 1/4 3 1 7/8 1 3/4 8 8 .561 .561 3 1/4 3 1/4 .266 .266 5 1/2 4 3/4 5/8-11 5/8-11 UNC UNC 4 4 2 1/2 2 7 6 3 l0 11/l6 6 3 11/16 1 7/8 8 .561 3 1/4 .266 6 5/8-11 UNC 4 3 7 1/2 4 13 7 4 13/16 2 1/8 11 .686 3 1/4 .266 7 1/2 5/8-11 UNC 8 4 9 5 14 7 9/16 5 1 /4 2 1/4 11 .686 3 1/4 .266 8 1/2 3/4-10 UNC 8 5 10 6 15 3/1 6 7 15/16 5 7/8 2 1/4 11 .811 3 1/4 .266 9 1/2 3/4-10 UNC 8 6 11 8 17 3/4 9 3/16 6 15/16 2 1/2 16 .936 4 3/4 .563 11 3/4 3/4-10 UNC 8 8 13 1/2 10 20 1/2 10 1/2 8 3/8 2 13/16 16 1.123 4 3/4 .563 14 1/4 7/8-9 UNC 12 10 16 12 23 1/2 12 1/16 9 13/16 3 1/8 16 1.247 4 3/4 .563 17 7/8-9 UNC 12 12 19

*M - Tap Size **N - Number of Holes The Lug configuration is tapped in accordance with ANSI B1.1 course thread series, Class B through all sizes

WAFER
Specifications: MSS SP-67 API-609
P .O. Box 35229 Greensboro, NC 27425 1-800-645-0101 or (336) 668-0554 fax: 1-800-876-0109 or (336) 668-4070

Rating: 200 WOG

Disc 7000W Nl Plated Ductile 7001W Nl Plated Ductile Bronze 7100W Bronze 7101W 316SS 7210W 316SS 7211W

Stem 416SS 416SS 416SS 416SS 316SS 316SS

Seat Material Buna N EPDM Buna N EPDM Buna N EPDM

Body Style Wafer Wafer Wafer Wafer Wafer Wafer

Dimension Table (inches)

SIZE A B C D E F G H J P 2 9 3/8 5 3/8 3 1 3/4 4 8 .561 31/4 .266 2 2 1/2 10 3/16 5 15/16 3 1/4 1 7/8 4 3/4 8 .561 3 1/4 .266 2 1/2 3 l0 11/l6 6 3 11/16 1 7/8 5 1/4 8 .561 3 1/4 .266 3 4 13 7 4 13/16 2 1/8 6 1/8 11 .686 3 1/4 .266 4 5 14 7 9/16 5 1 /4 2 1/4 7 1 /2 11 .686 3 1/4 .266 5 6 15 3/1 6 7 15/16 5 7/8 2 1/4 8 1/2 11 .811 3 1/4 .266 6 8 17 3/4 9 3/16 6 15/16 2 1/2 10 5/8 16 .936 4 3/4 .563 8 10 20 1/2 10 1/2 8 3/8 2 13/16 12 1/2 16 1.123 4 3/4 .563 10 12 23 1/2 12 1/16 9 13/16 3 1/8 14 3/4 16 1.247 4 3/4 .563 12

# 1 2

3 4 5 6 7 9 10 12 13 14 15 16

ITEM DESCRIPTION Body Lug/Wafer Cast Iron Liner - Buna N Liner - EPDM Liner - VITON Disc - Bronze Disc - Ni Coated Ductile Iron Disc - 316 SS Upper Stem 416 SS Upper Stem 316 SS Lower Stem 416 SS Lower Stem 316 SS Upper Stem Bearing Upper Stem O-Ring Upper Stem O Ring Lower Stem Set Screw Position Plate 10 Pos./Inf. Pos. Lock Washer Hex Nut Hex Head Bolt Tangential Retaining Pin SIZE 2 2 1/2 3 4 5 6 8 10 12 0 PSI DRY WET 175 130 200 150 275 200 450 330 500 375 900 675 1200 900 2500 1900 3200 2400

MATERIAL SPECIFICATION QTY ASTMA-126-B 1 ASTM D-2000 1 ASTM D-2000 1 ASTM D-2000 1 ASTM B-62 1 ASTMA-395 (60-40-18) 1 ASTMA-351 Grade CF8M 1 ASTMA-582 1 ASTMA-479 1 ASTMA-582 1 ASTMA-479 1 Oil Impregnated Bronze 1 Buna N or EPDM or Viton 1 Buna N or EPDM or Viton 1 ASTMA-582 1 Carbon Steel 1 Carbon Steel (Cad Plated 2 Carbon Steel (Cad Plated) 2 Carbon Steel (Cad Plated) 2 Carbon Steel 1 200 PSI DRY WET 250 190 300 225 400 300 600 450 900 675 1450 1100 2000 1500 3800 2900 6000 4500

Specifications:
MSS SP-67 API-609 200 psi WOG

Bill of Material List

100 PSI WET DRY 220 160 250 190 350 260 550 420 825 620 1200 900 1600 1200 3000 2250 4500 3400

Approximate Operating Torque inch pounds)

Use these seating torques only as an estimating guide for actuator sizing. Any variations in the media condition will affect the operating torque. Flow in Gallons Per 6 12 10 8 5 4 3 2 2 1/2 Minute 100% Open 360 650 1400 1900 3300 5000 7500 130 190 33% Open 825 363 550 71 154 209 39 14 21 16 FPS @ Full Open 157 245 353 628 982 1413 2512 3925 5625 4 FPS @ Full Open 40 61 628 990 1413 88 157 245 353 "Cv Factors" A valves flow characteristic is generally described as its Cv factor . Cv is defined as the flow in GPM (Gallons Per Minute) that will produce a 1 pound pressure drop across the valve. Typically Butterfly Valves (other than high performance) are made up of two classes. Class A, designed for 8 FPS (Feet Per Second), or Class B, designed for 16 FPS. It is reccomended that all applications be sized using 16 FPS or less. While Butterfly Valves will allow flow much greater than 16 FPS, this velocity assures that the valve installation and its piping system will give many years of satisfactory service. It is also recommended that no Butterfly Valve be installed in a throttling application where the valve will be open less than 33% or less than 30 degrees. It is further recommended that no obstruction, equipment or pipeline deviation be installed closer than 8 times the pipe diameter downstream of the valve installation. This allows for flow stabilization in the piping system, thus eliminating potential erosion or cavitation. 12 10 8 6 5 4 2 2 1/2 3 SERIES 7000 Shipping Weights 99 22 39 64 14 18 10 9 7 Wafer style with handle 104 26 44 69 18 22 Wafer style with gear operator 11 13 14 117 28 47 98 20 24 10 11 9 Lug style with handle 122 32 52 103 24 28 13 14 15 Lug style with gear operator

Gear Operators
All Series 7000 Butterfly Valves are available with gear operators which feature ductile iron handwheels and weather proof seals as standard Internal operation is through a worm drive and segment gear and is permanently lubricated in a grease bath. All gear operators are suitable for either open left or open right operation and have independent and fully adjust able stops for shaft and disc position location. Disc position is indicated by a low profile indicator with flag style optional. Other options such as 2" square operating nuts and stem extensions are available

DET. NO. 1 2 3 4 5 6 7 8

QUANT . 1 1 1 1 1 1 2 2

DESCRIPTION Housing Drive Sleeve Worm Cover Plate Indicator Plate Worm Shaft Stop Screw Lock Nut

DET. NO. 9 10 11 12 13 14 15

QUANT. 2 1 2 1 2 2 1

DESCRIPTION Thrust Bearing Freeze Plug O Ring Seal Hex Cap Screw Hex Cap Screw Roll Pin

Dimension Table (inches)

2 SIZE 41/8 A 4 11/16 B 2 5/8 C 2 3/4 D 1.725 E 7 F 2 1/4 G 3 1/4 H 1.0625 I .266 J 6 K 3 R 2 1/4 S 7 T 24-1 RATIO 6# WT. 2 1/2 4 1/8 4 11/16 2 5/8 2 3/4 l.725 7 2 l /4 3 1/4 l.0625 .266 6 3 2 1/4 7 24-l 6# 3 4 1/8 4 11/16 2 5/8 2 3/4 1.725 7 2 1/4 3 1/4 1.0625 .266 6 3 2 1/4 7 24-1 6# 4 4 1/8 411/16 2 5/8 2 3/4 l.725 7 2 1/4 3 1/4 1.0625 .266 6 3 2 1/4 7 24-1 6# 5 4 1/8 4 11/16 2 5/8 2 3/4 1.725 7 2 1/4 3 1/4 1.0625 .266 6 3 2 1/4 7 24-1 6# 6 4 1/8 4 11/16 2 5/8 2 3/4 1.725 7 2 1/4 3 1/4 1.0625 .266 6 3 2 1/4 7 24-1 6# 8 5 1/8 6 1/8 3 9/16 4 1/8 2.500 7 2 9/1 6 4 3/4 1.1250 .563 10 3 2 9/1 6 11 30-1 10# 10 5 1/8 6 1/8 3 9/16 4 1/8 2.500 7 2 9/16 4 3/4 1.1250 .563 10 3 2 9/16 11 30-1 10# 12 5 1 /8 6 1/8 3 9/1 6 4 1/8 2.500 7 2 9/1 6 4 3/4 1.1250 .563 12 3 2 9/1 6 11 30-1 10#

Reference Information
P .O. Box 35229 Greensboro, NC 27425 1-800-645-0101 or (336) 668-0554 fax: 1-800-876-0109 or (336) 668-4070

7000W 7001W 7000L 7001L 7100W 7l0lW 7100L 7101L 7210W 7211W 7210L 7211L

Disc Nl Plated Ductile Nl Plated Ductile Nl Plated Ductile Nl Plated Ductile Bronze Bronze Bronze Bronze 316SS 316SS 316SS 316SS

Stem 416SS 416SS 416SS 416SS 416SS 416SS 416SS 416SS 316SS 316SS 316SS 316SS

Seat Material Body Style Wafer Buna N Wafer EPDM Lug Buna Lug EPDM Wafer Buna N Wafer EPDM Lug Buna N Lug EPDM Wafer Buna N Wafer EPDM Lug Buna N Lug EPDM

AMERICAN SERIES 7000 Centerline Crane Demco Dezurik Grinnel Hammond Keystone Milwaukee Mueller Nibco Norris Stockham Watts AMERICAN SERIES 7000 Centerline Crane Demco Dezurik Grinnel Hammond Keystone Milwaukee Mueller Nibco Norris Stockham Watts

7000L 7000W Series LT Series A 23/24N FRB 21/22N FRB NE 511531 NL 111535 632L/660L 632W/660W LD 8191 WD-8191 6200 6100 122/129 100 ML1722B MWl22B 52-ANI-3 51-ANI-3 LD-3110 WD-3110 R 3011 R-1011 LD-511-DS3-B LD-711-DS3-B BF-03-111-2 BF-04-111-2

7001W Series A 21/22N-FRZ NE-111536 632W/660W WD-8291 6101 100/239 MWl22E 51-ANI 6 WD-3010 R 1011 LD-511-DS3-E BF 04-111-1

7001L Series LT 23/24N-FRZ NE-511531 632L/660L LD-8291 6201 1 22/129 MLl22E 52-ANI-6 LD-3010 R-3011 LD 711-DS3-E BF 03-111-1

7100W Series A 12F-TL NE-111435 632W/660W WC-8181 6110 100/239 MLl23B 51 -ANK-3 WD2100 R-l011 LD 511-BS3-B BF-04-121-2

7100L Series LT 14W-TL NE-511431 632L/660L LC-8181 6210 122/129 MLl238 52-ANK-3 LD-2100 R-3011 LD 711 BS3-B BF-03-121-2

7101W Series A 12F-TL NE-111435 632W/660W WC-8181 6111 100/239 MWl23E 51-ANK-6 WD-2000 R-1011 LD-511-BS3-E BF-04-12-12

7101L Series LT 14W-TL NE-511431 632L/660L LC-8281 6211 129/122/228 MLl23E 52-ANK-6 LD-2000 R 3011 LD-711-BS3-E BF-03-121-1

7711W Series A 44N-SSZ NE-l12235 632W/660W LD 8271 6121 100 MWl24E 51H-AHH 6 WD-3022 R l0ll LD-51l-SS2 E BF-04-131-1

7211L Series LT 42N-SSZ NE-51/2231 632L/660L WD 8271 6221 122 MLl24E 52-AHH 6 LD 3022 R-3011 LD -711-SS2E BF-03-131-1