Erm320240 1

EA Graphic Module User Manual ERM320240-1 Series
URL: www.lcd-china.com
www.l cd-chi na. com
EastRising

ERM320240-1 Series
Graphic Module User Manual

EastRising Technology Co., Limited

Attention:
A. Click CONTENTS list could be directed to the detail page. Click Return to CONTENTS could be directed to CONTENTS Page.
B. Some specifications of IC are not listed in this manual. Please refer to the IC manual for more details.
C. The drawing for related touch panel, schematic drawing, demo code is all available, please contact with our sales if you need.
D. Please pay more attention to INSPECTION CRITERIA in this manual. We assume you already agree with these criterions when you place an
order with us. No more recommendations.

REV DESCRIPTION RELEASE DATE
1.0 Preliminary Release J uly-09-2012

Document Name: ERM320240-1 Series Manual-Rev1.0 Page: 1 of 21


URL: www.lcd-china.com Document Name: ERM320240-1 Series Manual-Rev1.0 Page: 2 of 21

EastRising
CONTENTS

1. ORDERING INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04
1.1 ERM320240-1 Series Table- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 04
1.2 ERM320240-1 Series Image- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 05
2. ATTRIBUTES - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06
2.1 Display Attribute - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06
2.2 Mechanical Attribute - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06
2.3 Electrical Attribute - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06
2.4 Optical Attribute- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 06
3. OUTLINE DRAWING- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 07
4. ELECTRICAL SPEC - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 08
4.1 Pin Configuration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 08
4.2 Absolute Maximum Ratings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
4.3 Electrical Characteristics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
5. INSPECTION CRITERIA - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
5.1 Acceptable Quality Level - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
5.2 Definition of Lot - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
5.3 Condition of Cosmetic Inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
5.4 Module Cosmetic Criteria - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
5.5 Screen Cosmetic Criteria (Non-Operating) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
5.6 Screen Cosmetic Criteria (Operating) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
6. PRECAUTIONS FOR USING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
6.1 Handling Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
6.2 Power Supply Precautions- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
6.3 Operating Precautions - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
6.4 Mechanical/Environmental Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
6.5 Storage Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
6.6 Others - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18



EastRising
7. USING LCD MODULES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19
7.1 Liquid Crystal Display Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19
7.2 Installing LCD Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 19
7.3 Precaution for Handling LCD Modules - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
7.4 Electro-Static Discharge Control- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
7.5 Precaution for Soldering to EastRising LCM- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
7.6 Precaution for Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21
7.7 Limited Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21
7.8 Return Policy - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21



EastRising
1. ORDERING INFORMATION
1.1 ERM320240-1 Series Table >>Return to CONTENTS
*The number of series table is in accordance with number of the below series image 1.2.

No. Part Number LCD Type Backlight Color Graphic & Font Color Background Color
1 ERM320240SYG-1 STN Positive Yellow Green Color Dark Blue Yellow Green Color
2 ERM320240SBS-1 STN Negative Blue White Color White Color Blue Color
3 ERM320240FS-1 FSTN Positive White Color Black Color White Color
4 ERM320240FR-1 FSTN Positive Red Color Black Color Red Color
5 ERM320240FG-1 FSTN Positive Green Color Black Color Green Color
6 ERM320240FB-1 FSTN Positive Blue Color Black Color Blue Color
7 ERM320240FP-1 FSTN Positive Purple Color Black Color Purple Color
8 ERM320240FAM-1 FSTN Positive Amber Color Black Color Amber Color
9 ERM320240DNYG-1 FFSTN Negative Yellow Green Color Yellow Green Color Black Color
10 ERM320240DNS-1 FFSTN Negative White Color White Color Black Color
11 ERM320240DNR-1 FFSTN Negative Red Color Red Color Black Color
12 ERM320240DNG-1 FFSTN Negative Green Color Green Color Black Color
13 ERM320240DNB-1 FFSTN Negative Blue Color Blue Color Black Color
14 ERM320240DNP-1 FFSTN Negative Purple Color Purple Color Black Color
15 ERM320240DNAM-1 FFSTN Negative Amber Color Amber Color Black Color



EastRising
1.2 ERM320240-1 Series Image >>Return to CONTENTS
*The number of series image is in accordance with number of the above series table 1.1.

1 2 3 4
5 6 7 8
9 10 11 12
13 14 15



EastRising
2. ATTRIBUTES
2.1 Display Attributes >>Return to CONTENTS
ITEM STANDARD VALUE UNIT
Dot Matrix 320 x 240 Dots --
Display Connector Pin Header 2016Pins or FFC 16 Pins --
Operating Temperature -20 ~+70
Storage Temperature -30 ~+80
Touch Panel Optional Yes ( Related Part Number: ER-TP057-1) --
Font Chip Optional N/A --
*Sunlight Readable No1,No3,No4,No5,No6,No7,No8 --
*Number of sunlight readable is from 1.1 ERM320240-1 Series Table of the manual.
2.2 Mechanical Attributes >>Return to CONTENTS
Outline Dimension 160.0(W) 109.0(H) 12.0(T) (MAX) mm
Visual Area 122.0(W) 92.0(H) mm
Active Area 115.17(W) 86.37(H) mm
Dot Size 0.33x0.33 mm
Dot Pitch 0.36x0.36 mm
Net Weight 205 15% grams (typical) g

2.3 Electrical Attributes >>Return to CONTENTS
IC Package SMT --
Controller RA8835 --
Interface 8080 8-bit Parallel --

2.4 Optical Attributes >>Return to CONTENTS
LCD Type Refer to 1.1 ERM320240-1 Series Table --
Backlight Color Refer to 1.1 ERM320240-1 Series Table --
Viewing Direction 6:00 Clock
LCD Duty 1/240 Duty
LCD Bias 1/16 Bias


EastRising
3. OUTLINE DRAWING >>Return to CONTENTS
C
u
s
t
o
m
e
r

N
O
.
:
C
u
s
t
o
m
e
r
:
C
u
s
t
o
m
e
r

A
p
p
r
o
v
e

B
y
:
A
0
R
E
V
.
D
E
S
C
R
I
P
T
I
O
N

O
F

M
O
D
I
F
Y
1
'S
T
,
D
E
S
I
G
N
M
O
D
I
F
Y

B
Y
W
S
L
M
a
r
-
0
8
-
2
0
1
1
D
A
T
E
E
a
s
t
R
i
s
i
n
g

T
e
c
h
n
o
l
o
g
y

C
o
.
,
L
t
d
w
w
w
.
l
c
d
-
c
h
i
n
a
.
c
o
m
E
a
s
t
R
i
s
i
n
g




EastRising
4. ELECTRICAL SPEC
4.1 Pin Configuration >>Return to CONTENTS
Pin
No.
Pin
Name
Descriptions
1 GND Power Ground
2 VCC Power Positive
3 V0 Negative Volt Adjust
4 WR
Write Signal
5 RD Read Signal
6 CS Chip Select
7 A0 H: Data L: Instruction Code
8 RST Reset Signal
9 DB0 Data Bus
10 DB1 Data Bus
11 DB2 Data Bus
12 DB3 Data Bus
13 DB4 Data Bus
14 DB5 Data Bus
15 DB6 Data Bus
16 DB7 Data Bus
17 NC No Connection
18 VEE Negative Volt Supply
19 LED_A Backlight Anode(+5V)
20 LED_K Backlight Cathode(0V)
J 2 / J 3 / J 4
1 D0
2 D1
3 D2
4 D3

Data bus
5 DISP Display on / off
6 FLM Frame Signal
7 M Alternate signal for LCD
8 LP Data Latch Pulse
9 CP Data Shift Pulse
10 VCC Power Positive
11 GND Power Ground
12 VOUT Negative Volt Output


EastRising
13 V0 Negative Volt Adjust
14 FG Frame Ground
15 LED_A Backlight Anode(+5V)
16 LED_K Backlight Cathode(0V)




EastRising

4.2 Absolute Maximum Ratings >>Return to CONTENTS
ITEM SYMBOL MIN. TYP. MAX. UNIT
Power Supply for Logic VDD-VSS -0.3 - +7.0 V
Power Supply for LCD VEE -0.3 - +25.0 V
Input Voltage VIN -0.3 - VDD+0.3 V
Supply Current for Backlight ILED - 200 - mA

4.3 Electrical Characteristics >>Return to CONTENTS
ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT
Power Supply for LCM VDD-VSS - 4.8 5.0 5.2 V
VIL L Level VSS - 0.2VDD V Input Voltage
VIH H Level 0.5VDD - VDD V
LCD Driving Voltage VDD-V0 - 22.8 23.0 23.2 V
Supply Current for LCM IDD VDD=5.0V - - 80.0 mA



EastRising

5. INSPECTION CRITERIA
5.1 Acceptable Quality Level >>Return to CONTENTS
Each lot should satisfy the quality level defined as follows

PARTITION AQL DEFINITION
A. Major 0.4% Functional defective as product
B. Minor 1.5% Satisfy all functions as product but not satisfy cosmetic stanard

5.2 Definition of Lot
One lot means the delivery quantity to customer at one time.
5.3 Condition of Cosmetic Inspection >>Return to CONTENTS
INSPECTION AND TEST
-FUNCTION TEST
-APPEARANCE INSPECTION
-PACKING SPECIFICTION

INSPECTION CONDITION
- Put under the lamp (20w2) at a distance 100mm from
- Tilt upright 45 degree by the front (back) to inspect LCD appearance.
AQL INSPECTION LEVEL
- SAMPLING METHOD: MIL-STD-105D
- SAMPLING PLAN: SINGLE
- MAJ OR DEFECT: 0.65% (MAJ OR)
- MINOR DEFECT: 2.5% (MINOR)
- GENERAL LEVEL: II/NORMAL


EastRising
5.4 Module Cosmetic Criteria >>Return to CONTENTS
NO. Item Judgment Criterion Partition
1 Difference in Spec. None allowed Major
2 Pattern Peeling No substrate pattern peeling and floating Major
No soldering missing Major
No soldering bridge Major
3 Soldering defects
No cold soldering Minor
4 Resist flaw on substrate Invisible copper foil(0.5mm or more)on substrate pattern Minor
No soldering dust Minor 5 Accretion of metallic
Foreign matter No accretion of metallic foreign matters(Not exceed0.2mm)
6 Stain No stain to spoil cosmetic badly Minor
7 Plate discoloring No plate fading,rusting and discoloring Minor
8 Solder amount

1.Lead parts

a. Soldering side of PCB

Solder to form aFilet
all around the lead.
Solder should not hide the
lead form perfectly.(too much)
b.Components side
(In case of Through Hole PCB)

Solder to reach the Components side of PCB

Minor

2.Flat packages Either toe(A) or heal (B) of
the lead to be covered by Filet.

Lead form to be assume over
Solder.

Minor

3.Chips (3/2) Hh(1/2)H

Minor
A B
h
H



EastRising
9 Backlight defects 1.Light fails or flickers.(Major)
2. Color and luminance do not correspond to specifications.
(Major)
3.Exceeds standards for displays blemishes, foreign matter,
dark lines or scratches.(Minor)

See
list

10 PCB defects Oxidation or contamination on connectors.*
2. Wrong parts, missing parts, or parts not in specification.*
3.J umpers set incorrectly.(Minor)
4.Solder(if any)on bezel,LED pad,zebra pad,or screw hole
pad is not smooth.(Minor)
*Minor if display functions correctly.Major if the display fails.

See
list

11 Soldering defects

1. Unmelted solder paste.
2. Cold solder joints,missing solder connections,or oxidation.*
3. Solder bridges causing short circuits.*
4. Residue or solder balls.
5. Solder flux is black or brown.
*Minor if display functions correctly.Major if the display fails.
Minor



EastRising
5.5 Screen Cosmetic Criteria (Non-Operating) >>Return to CONTENTS
No. Defect Judgment Criterion Partition
1 Spots In accordance with Screen Cosmetic Criteria (Operating) No.1. Minor
2 Lines In accordance with Screen Cosmetic Criteria (Operation) No.2. Minor

Size: d mm Acceptable Qty in active area
d0.3
0.3<d1.0
1.0<d1.5
1.5<d
Disregard
3
1
0
Minor

3

Bubbles in
Polarizer

4

Scratch

In accordance with spots and lines operating cosmetic criteria, When the
light reflects on the panel surface, the scratches are not to be remarkable.
Minor

5 Allowable density Above defects should be separated more than 30mm each other. Minor
6

Coloration

Not to be noticeable coloration in the viewing area of the LCD panels.
Back-lit type should be judged with back-lit on state only.
Minor

7 Contamination Not to be noticeable. Minor


EastRising
5.6 Screen Cosmetic Criteria (Operating) >>Return to CONTENTS
A) Clear
Size:d mm Acceptable Qty in active area
d0.1
0.1<d0.2
0.2<d0.3
0.3<d
Disregard
6
2
0
Note: Including pin holes and defective dots which must be within one pixel
Size.
B) Unclear
Size:d mm Acceptable Qty in active area
1 Spots
d0.2
0.2<d0.5
0.5<d0.7
0.7<d
Disregard
6
2
0
Minor
2 Lines A) Clear

Note: () Acceptable Qty in active area
L - Length (mm)
W -Width(mm)
-Disregard
B) Unclear

Minor
Clear =The shade and size are not changed by Vo.
Unclear =The shade and size are changed by Vo.
L 5.0
2.0
8
0.02 0.05 0.1
W
See No.1
(0)
(6)
L 10.0
2.0
8
(6)
(0)
0.05 0.3 0.5
See No.1
W



EastRising
3 Rubbing line Not to be noticeable.
4 Allowable density Above defects should be separated more than 10mm each other. Minor
5 Rainbow Not to be noticeable. Minor
6 Dot size To be 95%~105%of the dot size (Typ.) in drawing.
Partial defects of each dot (ex.pin-hole) should be treated asspot.
(see Screen Cosmetic Criteria (Operating) No.1)
Minor
7 Brightness
(only back-lit
Module)

Brightness Uniformity must be BMAX/BMIN2
- BMAX :Max.value by measure in 5 points
- BMIN : Min.value by measure in 5 points
Divide active area into 4 vertically and horizontally.
Measure 5 points shown in the following figure.

Minor
8 Contrast
Uniformity
Contrast Uniformity must be BmAX/BMIN2
Measure 5 points shown in the following figure.
Dashed lines divide active area into 4 vertically and horizontally.
Measuring points are located at the inter-sections of dashed line.

Note: BMAX Max.value by measure in 5 points.
BMIN Min.value by measure in 5 points.
O Measuring points in 10mm.
Minor
Note:
(1) Size : d=(long length +short length)/2
(2) The limit samples for each item have priority.
(3) Complexed defects are defined item by item, but if the number of defects is defined in above table, the total
number should not exceed 10.



EastRising
(4) In case of concentration, even the spots or the lines of disregarded size should not be allowed. Following three
situations
Should be treated as concentration.
-7 or over defects in circle of 5mm.
-10 or over defects in circle of 10mm
-20 or over defects in circle of 20mm

6. PRECAUTIONS FOR USING EastRising EastRising EastRising EastRising EastRising
6.1 Handling Precautions >>Return to CONTENTS
This device is susceptible to Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions.
EastRising display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact.
If EastRising display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in
your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.
Do not apply excessive force to the EastRising display surface or the adjoining areas since this may cause
the color tone to vary.
The polarizer covering the EastRising display surface of the LCD module is soft and easily scratched.
Handle this polarizer carefully.
If EastRising display surface becomes contaminated, breathe on the surface and gently wipe it with a soft
dry cloth. If it is heavily contaminated, moisten cloth with one of the following Isopropyl or alcohol.
Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the Water.
Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water
droplets, moisture condensation or a current flow in a high-humidity environment.
Install the EastRising LCD Module by using the mounting holes. When mounting the LCD module make
sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the cable or the
backlight cable.
Do not attempt to disassemble or process EastRising LCD module.
NC terminal should be open. Do not connect anything.
If the logic circuit power is off, do not apply the input signals.
To prevent destruction of the elements by static electricity, be careful to maintain an optimum work
environment.
-Be sure to ground the body when handling EastRising LCD modules.
-Tools required for assembling, such as soldering irons, must be properly grounded.
-To reduce the amount of static electricity generated, do not conduct assembling and other work under dry
conditions.
-The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this
protective film since static electricity may be generated.



EastRising

6.2 Power Supply Precautions >>Return to CONTENTS
Identify and, at all times, observe absolute maximum ratings for both logic and LC drivers. Note that there is
some variance between models.
Prevent the application of reverse polarity to VDD and VSS, however briefly.
Use a clean power source free from transients. Power-up conditions are occasionally jolting and may
exceed the maximum ratings of EastRising modules.
The VDD power of EastRising module should also supply the power to all devices that may access the
display. Dont allow the data bus to be driven when the logic supply to the module is turned off.
6.3 Operating Precautions >>Return to CONTENTS
DO NOT plug or unplug EastRising module when the system is powered up.
Minimize the cable length between EastRising module and host MPU.
For models with backlights, do not disable the backlight by interrupting the HV line. Unload inverters
produce voltage extremes that may arc within a cable or at the display.
Operate EastRising module within the limits of the modules temperature specifications.
6.4 Mechanical/Environmental Precautions >>Return to CONTENTS
Improper soldering is the major cause of module difficulty. Use of flux cleaner is not recommended
as they may seep under the electrometric connection and cause display failure.
Mount EastRising module so that it is free from torque and mechanical stress.
Surface of the LCD panel should not be touched or scratched. The display front surface is an easily
scratched, plastic polarizer. Avoid contact and clean only when necessary with soft, absorbent cotton
dampened with petroleum benzene.
Always employ anti-static procedure while handling EastRising module.
Prevent moisture build-up upon the module and observe the environmental constraints for storage tem
Do not store in direct sunlight
If leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion.
If the body or clothing becomes contaminated by the liquid crystal material, wash thoroughly with water and
soap
6.5 Storage Precautions >>Return to CONTENTS
When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps.
Keep EastRising modules in bags (avoid high temperature / high humidity and low temperatures below 0C
Whenever possible, EastRising LCD modules should be stored in the same conditions in which they were
shipped from our company.
6.6 Others >>Return to CONTENTS
Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective
orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module



EastRising
is subject to a low temperature.
If EastRising LCD modules have been operating for a long time showing the same display patterns, the
display patterns may remain on the screen as ghost images and a slight contrast irregularity may also
appear. A normal operating status can be regained by suspending use for some time. It should be noted that
this phenomenon does not adversely affect performance reliability.
To minimize the performance degradation of the LCD modules resulting from destruction caused by static
electricity etc., exercise care to avoid holding the following sections when handling the modules.
-Exposed area of the printed circuit board.
-Terminal electrode sections.
7. USING LCD MODULES
7.1 Liquid Crystal Display Modules >>Return to CONTENTS
EastRising LCD is composed of glass and polarizer. Pay attention to the following items when handling.
Please keep the temperature within specified range for use and storage. Polarization degradation, bubble
generation or polarizer peel-off may occur with high temperature and high humidity.
Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass,
tweezers, etc.).
N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors
made of organic substances which will be damaged by chemicals such as acetone, toluene, ethanol and
isopropylalcohol.
When EastRising display surface becomes dusty, wipe gently with absorbent cotton or other soft material
like chamois soaked in petroleum benzin. Do not scrub hard to avoid damaging the display surface.
Wipe off saliva or water drops immediately, contact with water over a long period of time may cause
deformation or color fading.
Avoid contacting oil and fats.
Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers.
After products are tested at low temperature they must be warmed up in a container before coming is
contacting with room temperature air.
Do not put or attach anything on EastRising display area to avoid leaving marks on.
Do not touch the display with bare hands. This will stain the display area and degradate insulation
between terminals (some cosmetics are determinated to the polarizers).
As glass is fragile. It tends to become or chipped during handling especially on the edges. Please
avoid dropping or jarring.

7.2 Installing LCD Modules >>Return to CONTENTS
Cover the surface with a transparent protective plate to protect the polarizer and LC cell.
When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting
plate should have enough height to avoid causing stress to the module surface, refer to the individual
specifications for measurements. The measurement tolerance should be0.1mm.



EastRising
7.3 Precaution for Handling LCD Modules >>Return to CONTENTS
Since EastRising LCM has been assembled and adjusted with a high degree of precision; avoid applying
excessive shocks to the module or making any alterations or modifications to it.
Do not alter, modify or change the shape of the tab on the metal frame.
Do not make extra holes on the printed circuit board, modify its shape or change the positions of
components to be attached.
Do not damage or modify the pattern writing on the printed circuit board.
Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
Do not drop, bend or twist EastRising LCM.

7.4 Electro-Static Discharge Control >>Return to CONTENTS
Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as
for an ordinary CMOS IC.
Make certain that you are grounded when handing LCM.
Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body
have the same electric potential.
When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.
When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to
minimize as much as possible any transmission of electromagnetic waves produced sparks coming from the
commutator of the motor.
As far as possible make the electric potential of your work clothes and that of the work bench the ground
potential.
To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative
humidity of 50%-60% is recommended.

7.5 Precaution for Soldering to EastRising LCM >>Return to CONTENTS
Observe the following when soldering lead wire, connector cable and etc. to the LCM.
-Soldering iron temperature : 28010
-Soldering time: 3-4 sec.
-Solder: eutectic solder.
If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This
does not apply in the case of a non-halogen type of flux.) It is recommended that you protect the LCD
surface with a cover during soldering to prevent any damage due to flux spatters.
When soldering the electroluminescent panel and PC board, the panel and board should not be detached
more than three times. This maximum number is determined by the temperature and time conditions
mentioned above, though there may be some variance depending on the temperature of the soldering iron.
When remove the electroluminescent panel from the PC board, be sure the solder has completely melted,
the soldered pad on the PC board could be damaged.



EastRising
7.6 Precaution for Operation >>Return to CONTENTS
Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best
contrast.
Driving the EastRising LCD in the voltage above the limit shortens its life.
Response time is greatly delayed at temperature below the operating temperature range. However, this
does not mean the LCD will be out of the order. It will recover when it returns to the specified temperature
range.
If EastRising display area is pushed hard during operation, the display will become abnormal. However, it
will return to normal if it is turned off and then back on.
Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore,
it must be used under the relative condition of 40, 50% RH.
When turning the power on, input each signal after the positive/negative voltage becomes stable.

7.7 Limited Warranty >>Return to CONTENTS
Unless agreed between EastRising and customer, EastRising will replace or repair any of its LCD modules
which are found to be functionally defective when inspected in accordance with EastRising LCD acceptance
standards (copies available upon request) for a period of one year from date of shipments. Cosmetic/visual
defects must be returned to EastRising within 90 days of shipment. Confirmation of such date shall be based
on freight documents. The warranty liability of EastRising limited to repair and/or replacement on the terms set
forth above. EastRising will not be responsible for any subsequent or consequential events.
7.7 Return Policy >>Return to CONTENTS
No warranty can be granted if the precautions stated above have been disregarded. The typical
examples of violations are:
-Broken LCD glass.
-PCB eyelet damaged or modified.
-PCB conductors damaged.
-Circuit modified in any way, including addition of components.
-PCB tampered with by grinding, engraving or painting varnish.
-Soldering to or modifying the bezel in any manner.
Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with
sufficient description of the failures or defects. Any connectors or cable installed by the customer must be
removed completely without damaging the PCB eyelets, conductors and terminals
.

Thats the end of the Manual >>Return to CONTENTS

Erm320240 1

Uploaded by

Copyright:

Available Formats

Erm320240 1

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Erm320240 1

Uploaded by

Copyright:

Available Formats

EA Graphic Module User Manual ERM320240-1 Series

You might also like