TV Plasma Belson Bsv4251 Bsv4251a Daewoo Pds2950 Pds4250 Chassis Sp120 Firstline Ept3400 Ept4200ap LG Pdp42v5 Tatung Tpt4202s

SERVICE MANUAL (BSV-4251 BSV-4251A )
Service Manual
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 1/75

CONTENTS
SPECIFICATION ..………………………………………………. 4
CONTROL DESCRIPTIONS …………………………………... 7
OPTIONS EXTRAS ..……………………..…………………… 9
REMOTE CONTROL BUTTONS ………..……………………. 10
DISPLAY CELL DEFECT SPECIFICATION …………………. 12
BLOCK & WIRING DIAGRAM …………………………………14
MODULE FUNCTION & DEFINITION ……………………….. 16
MODULE BASIC CONFIGURATION …………………….……17
VSC BOARD PIN CONFIGURATION …………….………….. 18
OSD MENU (FACTORY)……………………………………….. 21
DESCRIPTION OF VSC FUNCTIONS ……………………….. 32
CIRCUIT OPERATION & WAVEFORM……………………….. 34
MODULE SUPPLY VOLTAGE SEQUENCE …………………. 41
VSC & PSU POWER SEQUENCE ……………………….….... 42
VOLTAGE & W/B ADJUSTMENT……………………………… 44
SAFETY PRECAUTIONS …………………………………………49

BSV-4251/4251A RD(1) 00 03/10/23 2/75

(MODULE USE AND CONSIDERATIONS IN SERVICING)
TROUBLESHOOTING.…….…………………………..…………. 53
IMAGE STICKING CHARACTERISTICS ……………………… 64
ISM MODE………………………………………………………….. 66
SCHEMATIC &PRINTED CIRCUIT BOARD &EXPLODE VIEW ……… 67
EXPLODED VIEW PARTS LIST ………………………………… 69
REPLACMENT PARTS LIST …………………………………….. 71
EXPLODE VIEW …………………………………………………… 75
BSV-4251/4251A RD(1) 00 03/10/23 3/75

SPECIFICATIONS
Note : Specification and others are subject to change without notice for improvement.
● TV
1.Input Signal :
PAL
SECAM
SD,HD
VGA ~XGA
2. Tuner : PAL
SECAM
2. Input Voltage : AC 100V ~ 240V,@ 50/60Hz, 4A
3. Power Consumption : 320W

Stand-by : 5W
4. PDP Module : PDP42V51000,51300(YBT), 51330(new ASIC) - LGE
5. Speaker Impedance : 8 §Ù
6. Sound Output : 10W + 10W
7. Feature :
- AV Input (Bottom)
- Component1 Input (Bottom, DVD)
- Component2 Input (Bottom, DTV)
- D-SUB (Bottom, RGB 15 pin)
- S-Video Input (Bottom,4Pin DIN)
- SCART1 Input (Bottom, Full)
- SCART2 Input (Bottom, Half)
- Tuner (Bottom, PAL,SECAM)
- External SPK Out (Bottom, SPK Jack)
- Audio Input (Bottom,RCA Jack,AV,Component1/2,S-Video,RGB)
- RS-232C (9 pin) , TCP / IP Support (0~255set)
8. Function :
- ARC
- PIP (PIP Swap,Sound Swap)
- PBP (4:3,16:9)
- MTS
- TTX
9. External Interface
BSV-4251/4251A RD(1) 00 03/10/23 4/75

1) AV / COMPONENT Output
ITEM MIN TYP MAX UNIT

AV Video Input Level 0.85 1.00 1.15 Vpp
AV Sync Input Level 0.24 0.29 0.32 Vpp
AV Burst Input Level 0.14 0.28 0.35 Vpp
AV Video Input Level 0.47 0.63 0.79 V
AV Audio Input L/R 0.47 0.63 0.79 V
Component Video Input Level
0.6 0.7 0.8 Vpp
(Y,Cb/Pb,Cr/Pr)
Analog RGB, H/V Input Level 0.6 0.7 0.8 Vpp
2) COMPONENT Mode (Y,Cb/Pb,Cr/Pr)
RESOLUTION H-Freq(KHz) V-Freq(Hz) Proposed

720*480 15.73 60.00 SDTV,DVD 480I
720*576 15.63 50.00 SDTV,DVD 576I
720*480 31.47 59.94 SDTV 480P
1280*720 45.00 60.00 HDTV 720P
1280*720 44.96 59.94 HDTV 720P
1920*1080 33.75 60.00 HDTV 1080I
1920*1080 33.72 59.94 HDTV 1080I
3)SUPPORTIING DISPLAY Mode

* It is optimal screen when the resolution is 640 * 480
RESOLUTION H-Freq(KHz) V-Freq(Hz)

31,47 60
640*480 37.86 72
37.50 75
720*400 31.47 70
35.15 56
37.88 60
800*600
48.88 72
46.88 75
48.36 60
1024*768 56,48 70
60.02 75
10. RS-232C Signal
BSV-4251/4251A RD(1) 00 03/10/23 5/75

Pin No Pin Name Spec Pin No Pin Name Spec
1 DCD NC 6 DSR NC
2 RXD 12 Vpp 7 RTS NC
3 TXD 12 Vpp 8 CTS NC
4 DTR NC 9 R NC
5 GND GND
CONTROL DESCRIPTIONS
BSV-4251/4251A RD(1) 00 03/10/23 6/75

BSV-4251/4251A RD(1) 00 03/10/23 7/75

OPTIONAL EXTRAS
BSV-4251/4251A RD(1) 00 03/10/23 8/75

◐Optional extras can be changed or modified for quality improvement without notification new optional
extras can be added.
◐Contract your dealer for buying these items.
REMOTE CONTROL BUTTONS

※ When using the remote control aim it at the remote control sensor of the Monitor.
BSV-4251/4251A RD(1) 00 03/10/23 9/75

TELETEXT FUNCTION
BSV-4251/4251A RD(1) 00 03/10/23 10/75

DISPLAY CELL DEFECT SPECIFICATION
BSV-4251/4251A RD(1) 00 03/10/23 11/75

[ PDP42V51000,51300,51330]
DEFINITION OF CELL DEFECT ZONE
BSV-4251/4251A RD(1) 00 03/10/23 12/75

1) Definition of Cell defect Zone
2) Display Dot Diagram
BSV-4251/4251A RD(1) 00 03/10/23 13/75

24LC21
BSV-4251 &BSV-4251A (42") PDP TV BLOCK DIAGRAM
EEPROM
R,G,B,H,V 5 20.000MHz 80.000MHz

ANALOG RGB
(U2) TX0 +
(U8) 5 AD9883
BA7657 24 CH1 RGB 24 TX0 -
SWITCH
A/D 24 TX0+
COMPONENT1 Y,Pb,Pr 3 CONVERTER DE [23:0]
(DTV) 16 TX1 +
DO [23:0]
20.25MHz TX1 -
3 H SYNC
COMPONENT2 Y,Pb,Pr
(DVD) V SYNC SIL164 TX2 +
(U39) CH1 GB
VPC3230D-C5 DEN TMDS
TRANSMITTER TX2 -
VIDEO DCLK
TUNER 2 DECODER
CVBS V OUT2 (SUB)
Y,C OUT2
TXC +
COMPOSITE
IN H_SCART_OUT TXC -
(U21)
MODULE
CVBS,ID 2
4
20.25MHz
PW565 42"
HALF SCART
VIDEO IN/OUT
(U41) ADR[12:0]
CVBS,ID 2 V OUT1 VPC3230D-C5 CH2 GB 16 FSDQM[7:0]
FULL SCART K4S643232E X 2
VIDEO
VIDEO IN/OUT Y,C OUT1 2 SDRAM
DECODER FSDATA[63:0]
(MAIN)
CH,LU 2 CXA2089Q
S-VIDEO A/V A[21:0]
MUX(U3) 4 TM28F800B3
6.000MHz D[7:0]
FLASH
TTX_CVBS MOMORY
S-VIDEO SVIDEO_IN R/L 2
AUDIO IN
PC_IN R/L 2 SST39VF080AT
PC TTX RGB FLASH 24LC256
AUDIO IN (R,G,B,FB) EEPROM
BA7657 SDA5550
SCART_FULL F_SC_IN R/L 2 (U28) (U26) HY62U8200
AUDIO IN SWITCH 4 TTX RAM
SCART_HALF H_SC_IN R/L 2 DS232AS

24LC16 RS232 I/O EXTENDER REMOCON
AUDIO IN
EEPROM TRANSMITTER
COMPOSITE AV_IN R/L 2 MSP0 L/R
AUDIO IN MSP1 L/R
18.432MHz
SCART RGB(R,G,B,FB) SPK SPK
FULL SCART RS232 KYE
R L
RGB 4 2 DSUB-9P PAD
2 MSP_OUT1
DTV DTV_IN R/L 2 L/R
TDA7495S
AUDIO IN AUDIO AMP
VCC5 VCC3 VCC5A VCC5D VCC9
DVD DVD_IN R/L 2 (U45)
AUDIO IN MSP3453
AUDIO VCC12
TUNER PROCESSOR
AP1501-50 RC1117 AP1501-50 AP1501-50 KIA7809 5VST FAN
SIF
SCART_FULL 2 F_CVBS_OUT_R/L
AUDIO OUT 12V 12V 12V 12V 12V
12V 5V
SCART_HALF 2 H_CVBS_OUT_R/L
AUDIO OUT POWER
MODULE
BSV-4251/4251A RD(1) 00 03/10/23 14/75

BSV-4251/4251A RD(1) 00 03/10/23 15/75

MODULE FUNCTION & DEFINITION

1. The function of each part
Part name Main function
Y-Board (Scan Driver) Execution of the scan and sustain operation connecting scan electrode (Y-electrode) and FPC of panel
Z-Board (Common Sustain Driver) Execution of the sustain operation connecting sustain electrode (Z-electrode) and FPC of panel
X-Board (Address Driver) Execution of the address operation connecting the botton plate address electrode (X-electrode) and FPC of panel
Control Board Distribution to X, Y, Z board after creation of display data and driver timing for an image and sound signal to be input from outside
DC/DC-2 Board Distribution to X, Y, Z board after conversion from input voltage of Vs, Va, Voc to circuit logic voltage (5V)
FPC (Flexible Plate Circuit) The pattern connection of PCB and panel
COF (Chip On Film) It means to integrate a kind of IC Chip with FPC
2. A term and definition of defect

2.1 CELL DEFECT
Term The actual state A cause

Non lighting Cell Defect Cell is always “Off” ¢º a different thing or structural defect of Cell
Flashing Cell Defect Cell repeat On / Off ¢º a different thing or structural defect of Cell
Non-extinguishing Cell Defect Cell is always “On” ¢º a different thing or structural defect of Cell
High Intensity Cell Defect A cell is the brighter than others on same color ¢º a different thing or structural defect of Cell
BSV-4251/4251A RD(1) 00 03/10/23 16/75

MODULE BASIC CONFIGURATION
[PDP42V51000,51300,51330]
BSV-4251/4251A RD(1) 00 03/10/23 17/75

VSC BOARD PIN CONFIGURATION
Pin No I/O Specification Description

1 ( 5V ) I 5V VSC 5V Input
4 ( GND ) GND 5V Ground
J7 6 ( GND ) GND 5V Ground
11 ( 12V ) I 12V FAN 12V
12 ( GND ) GND FAN 12V Ground
AC POWER DETECT PORT
: AC INPUT DETECTING.
: AC POWER ON High ,
1 ( AC-DET ) I 5V / 0V AC POWER OFF LOW
:Turn off the power by power sequence to
stabilize PDP MODULE in case of power
breakdown.
3 ( 5V STBY ) I 5V 5V INPUT PORT FOR VSC STANDBY
J6 RELAY CONTROL PORT FOR POWER ON
2 ( RL-ON ) O 5V / 0V
: Relay On High , Relay off Low
PDP MODULE STABLE CHECK PORT.
: The port to provide control signal to PDP
6 ( 5V-MNT ) I 5V / 0V MODULE after the controller stabilized. At the
moment, MICOM always check this signal and
turn off the power when the signal is low.
4 ( GND )
PORT FOR VA/VS OF PDP MODULE.
: ON HIGH , OFF LOW
5 (VAVS-ON ) O 5V / 0V
:To protect PDP MODULE, Micom turn on the
Va/Vs 2 seconds after checking 5V-MNT.
7 ( NC ) No Connection
P2 1 ( REMOCON ) I 5V Monitor transmitter signal input port
2 ( GND )
3 ( 5VST ) O 5V Stand by 5V Output Port
4 ( GND )
RED LED CONTORL OUTPUT PORT
5 (LED-R ) O 5V / 0V
: High : Red LED On
GREEN LED CONTORL OUTPUT PORT
6 (LED-G ) O 5V / 0V
: High : Green LED On
BSV-4251/4251A RD(1) 00 03/10/23 18/75

7 ( POWER ) I 5V / 0V LOCAL KEY INPUT PORT FOR POWER
8 ( VOL+ ) I 5V / 0V LOCAL KEY INPUT PORT FOR VOL +
9 ( VOL- ) I 5V / 0V LOCAL KEY INPUT PORT FOR VOL -
10 ( SRC/SEL ) I 5V / 0V LOCAL KEY INPUT PORT FOR SOURCE
11 (MENU) I 5V / 0V LOCAL KEY INPUT PORT FOR MENU
12 (CH-) I 5V / 0V LOCAL KEY INPUT PORT FOR CH-
13 (CH+) I 5V / 0V LOCAL KEY INPUT PORT FOR CH+
1 ( 32V ) I 32V Audio AMP POWER INPUT PORT
2 ( 32V ) I 32V Audio AMP POWER INPUT PORT
J9
3 ( GND ) 0V Audio AMP POWER GROUND PORT
4 ( GND ) 0V Audio AMP POWER GROUND PORT
1 ( L OUT ) O Audio AMP LEFT OUTPUT PORT( 8 §Ù )
2 ( L GND ) Audio AMP LEFT GROUND PORT
J10
3 ( R OUT ) O Audio AMP RIGHT OUTPUT PORT ( 8 §Ù )
4 ( R GND ) Audio AMP RIGHT GROUND PORT
1 ( S-SCL ) RS-232C CLOCK LINE
2 ( S-SDA ) RS-232C DATA LINE
J11
3 ( FS )
4 ( GND ) 0V
J1 1 ( VCC5 ) I 5V 5V Input
2 ( VCC5 ) I 5V 5V Input
3 (SCART_R) I 0.7Vpp±0.1pp SCART RED INPUT PORT
4 (SCART_G) I 0.7Vpp±0.1pp SCART GREEN INPUT PORT
5 (SCART_B) I 0.7Vpp±0.1pp SCART BLUE INPUT PORT
6 (SCART_FB) I +1V to +3V / 0V to 0.4V SCART FAST BLANKING
7 ( GND ) 0V
8 (FSCART_CVBS_IN) I 1.0Vpp±3dB SCART1 CVBS INPUT PORT
9 ( GND )) 0V
10 (HSCART_CVBS_IN) I 1.0Vpp±3dB SCART2 CVBS INPUT PORT
11 ( GND ) 0V
12 ( FSCART_ID ) I 4:3 / 16:9 VIDEO STATUS
13 ( HSCART_ID ) I 4:3 / 16:9 VIDEO STATUS
14 ( GND ) 0V
15 (F_CVBS_OUT) O 1.0Vpp±3dB SCART1 CVBS OUTPUT PORT
16 ( GND ) 0V
17 (H_CVBS_OUT) O 1.0Vpp±3dB SCART2 CVBS OUTPUT PORT
18 ( GND ) 0V
19 (F_CVBS_L_OUT) O 0.5Vrms±3dB SCART1 AUDIO LEFT OUTPUT PORT
20 (F_CVBS_R_OUT) O 0.5Vrms±3dB SCART1 AUDIO RIGHT OUTPUT PORT
21 ( GND ) 0V
22 (H_CVBS_L_OUT) O 0.5Vrms±3dB SCART2 AUDIO LEFT OUTPUT PORT
23 (H_CVBS_R_OUT) O 0.5Vrms±3dB SCART2 AUDIO RIGHT OUTPUT PORT
BSV-4251/4251A RD(1) 00 03/10/23 19/75

24 ( GND ) 0V
1 ( VCC5) I 5V 5V INPUT
2 ( F_SC_L_IN ) I 0.5Vrms±3dB SCART1 AUDIO LEFT OUTPUT PORT
3 ( F_SC_R_IN ) I 0.5Vrms±3dB SCART1 AUDIO RIGHT OUTPUT PORT
4 ( GND ) 0V
5 ( H_ SC_L_IN ) I 0.5Vrms±3dB SCART2 AUDIO LEFT OUTPUT PORT
6 ( H_SC_R_IN ) I 0.5Vrms±3dB SCART2 AUDIO RIGHT OUTPUT PORT
7 ( GND ) 0V
8 ( AFT ) I
9 ( GND ) 0V
10 ( TUNER_SIF ) I
11 ( GND ) 0V
12 (TUNER_CVBS) I 1.0Vpp±3dB TV VIDEO INPUT PORT
J2
13 ( GND ) 0V
14 ( SDA3 ) I 5V / 0V DATA LINE
15 ( SCL3 ) I 5V / 0V CLOCK LINE
16 ( GND ) 0V
17 ( VCC12 ) I 12V 12V INPUT
18 ( VCC12 ) I 12V 12V INPUT
19 ( GND ) 0V
20 ( VCC5A ) I 5V 5V INPUT
21 (VCC5A ) I 5V 5V INPUT
22 ( GND ) 0V
23 ( GND ) 0V
24 ( GND ) 0V
OSD MENU(FACTORY)
■ FACTORY MODE
BSV-4251/4251A RD(1) 00 03/10/23 20/75

FACTORY MODE
„ 1. Calibration
: Automatic adjustment of white balance for Analogue input (PC) and Component2 (DTV)
input.
„ 2. Option Table 0002
: Initial installation of OSD.
„ 3. Color control
: Adjustment of contrast and brightness for scaler generating power.
„ 4. PW565
: Adjustment of contrast and brightness for scaler input port (CH1 or CH2).
„ 5. VPC3230-MAIN
: Value adjustment for video decoder¡¯s brightness and contrast, color tickness in
the main window.
„ 6. VPC3230-SUB
: Value adjustment for video decoder¡¯s brightness and contrast, color tickness in
the sub window.
„ 7. ADC
: Value adjustment for brightness and contrat, color thickness of analogue RGB,
Y,Pb,Pr of AD9883 A/D convertor.
„ 8. Heatrun
: The mode when you do aging.
„ 9. Version
: It shows the information of Firmware version and Panel.
„ 10. Setup
: Installation of TTX language and video, protocol, logo.
CALIBRATION MENU
BSV-4251/4251A RD(1) 00 03/10/23 21/75

CALIBRATION MENU
„ 1. PC Calibration
: Automatic adjustment as the fittest status of white balance for analogue input (PC)
„ 2. DTV Calibration
: Automatic adjustment as the fittest status of white balance for component2 (DTV)
input.
OPTION TABLE MENU
BSV-4251/4251A RD(1) 00 03/10/23 22/75

OPTION TABLE MENU

„ Flesh tone
„ LNA(Low Noise Amplifier)

: On/Off Installation of screen quality improv ement fuc tion, when TV input signal is
weak.
„ Blue Screen
: When there are no input signal of the TV and external equipment, you can install the
screen color as blue.
„ Melody Volume
: Installation of the melody volume for initial soft power On/Off. The volume is ex-
factoried as ¡°0 ¡± due to license.
„ Video Mute
„ TTX TOP
„ Auto FM
„ Help
„ Area
„ High Deviation
COLOR CONTROL MENU
BSV-4251/4251A RD(1) 00 03/10/23 23/75

COLOR CONTROL MENU

„ Sub-Brightness
: The brightness adjustment of scaler generating power.
„ Red, Green, Blue Offset
: The brightness adjustment of each Red, Green, Blue for scaler generating power.
„ Brightness
: The brightness adjustment of current screen. Adjustment value of brightness for User
Menu
„ TTX-Bright
: It is not useful mode.
„ Sub Contrast
: Contrast adjustment of scaler generating power.
„ Red, Green, Blue Gain
: Contrast adjustment of each Red, Green, Blue for Scaler generating power.
„ Contrast
: Contrast adjustment for current screen. The value adjustment of contrast for User Menu
„ TTX-Contrast
PW565 MENU
BSV-4251/4251A RD(1) 00 03/10/23 24/75

PW565 MENU
„ Red,Green,Blue Gain
: The contrast value adjustment of each Red, Green, Blue for scaler input port (CH1 OR
CH2)
„ Red,Green,Blue Offset
: The brightness adjustment of each Red, Green, Blue for scaler input port (CH1 OR CH2)
„ APL
„ Pixel Shift
„ Pixel Number
„ Time
„ Virtual Framelock
: Installation of flame frequency for panel (50Hz, 60Hz).
„ Alpha
„ Beta
„ Degree
VPC3230-MAIN MENU
BSV-4251/4251A RD(1) 00 03/10/23 25/75

VPC3230-MAIN MENU
„ CT
: Contrast adjustment of Composite & S-Video form¡¯s signal.
„ BR
: Brightness adjustment of Composite & S-Video form¡¯s signal.
„ ACC_SAT
„ TINT
: The color sense adjustment of Composite & S-Video form¡¯s signal.
„ SATCb
: The blue color sense adjustment of Component & RGB form¡¯s signal.
„ SATCr
: The red color sense adjustment of Component & RGB form¡¯s signal
„ CIPTNT
: The color sense adjustment of Component & RGB form¡¯s signal.
„ CIPBR
: The brightness adjustment of Component & RGB form¡¯s signal.
„ KILVL
„ LDLY
: The delayed time adjustment of brightness signal.
„ PKCOR
„ FB_GAIN
VPC3230-SUB MENU
BSV-4251/4251A RD(1) 00 03/10/23 26/75

VPC3230-SUB MENU
„ CT
: The contrast adjustment of Composite & S-Video form¡¯s signal.
„ BR
: The brightness adjustment of Composite & S-Video form¡¯s signal.
„ ACC_SAT
„ TINT
: The color sense adjustment of Composite & S-Video form¡¯s signal.
„ SATCb
: The blue color sense adjustment of Component & RGB form¡¯s signal.
„ SATCr
: The red color sense adjustment of Component & RGB form¡¯s signal.
„ CIPTNT
: The color sense adjustment of Component & RGB form¡¯s signal.
„ CIPBR
: The brightness adjustment of Component & RGB form¡¯s signal.
„ KILVL
„ LDLY
: The delayed time installation of brightness signal.
„ PKCOR
„ FB_GAIN
ADC MENU
BSV-4251/4251A RD(1) 00 03/10/23 27/75

ADC MENU
„ Red, Green, Blue Gain

: Control ADC input range (Contrast) of each respective channel.
„ Red, Green, Blue Offset

: Control dc offset (Brightness) of each respective channel.
„ Current
: Installation of PLL Part VCO Current. (For test)
„ VCO
: Installation of PLL Part VCO Range (For test)
„ Pr, Y, Pb Gain
: Contrast adjustment of Component2 Pr, Y, Pb signal.
„ Pr, Y, Pb Offset
: Brightness adjustment of Component2 Pr, Y, Pb signal.
„ TTX Phase
„ TTX Contrast
HEATRUN MENU
BSV-4251/4251A RD(1) 00 03/10/23 28/75

HEATRUN MENU
„ 1. Auto Run
: It is the mode to change the heatrun pattern as a certain time interval.
„ 2. Luma Ramp (16 Step)
: It is gray pattern of 16 Step.

„ 3. Luma Ramp (128 Step)
: It is gray pattern of 128 Step.
„ 4. White 16
: It is low Gray pattern.
„ 5. White 240
: It is high gray pattern.

„ 6. Color Bar
: It is color Bar Pattern.
„ 7. RGB Ramp (32 Step)

: It is RGB Ramp pattern of 32 Step.
VERSION MENU
BSV-4251/4251A RD(1) 00 03/10/23 29/75

VERSION MENU
„ Version
: It is to show the Firmware Version.
„ Release
: It is to show the date of Firmware revision.
„ Panel Used Time
: It is to show the used time of Panel.

„ Panel Name
: It is to show the name of the PDP.
SETUP MENU
BSV-4251/4251A RD(1) 00 03/10/23 30/75

SETUP MENU
„ 1. TTX Language
: Installation of initial language of the TTX.
„ 2. Video
: Video format per country and it is composed of Normal, NTSC, PAL N, M
„ 3. Protocol
: Installation of communication protocol for remote control.

„ 4. LOGO
: Installation to show company logo on the screen when power ¡°On¡±(ON/OFF).
DESCRIPTION OF VSC FUNCTIONS

BSV-4251/4251A RD(1) 00 03/10/23 31/75

PSM (Picture Status Memory)
Function to adjust picture status to an optimal condition in accordance with the type of program being
viewed (standard, moving picture, movie, muted, game).
SSM (Sound Status Memory)
Function to adjust sound status to an optimal condition in accordance with the type of program being
viewed (standard, music, movie, news).
ARC (Aspect Ratio Control)
Function to adjust the picture size. (16:9. enlargement 1, enlargement 2, panorama, 4:3)
Panorama
Function to prevent pictures recorded in the 4:3 format from being stretched to the extreme left and right
when played on a 16:9 display. Since the focus of the camera is concentrated on the center, it naturally
enlarges the picture within the outer perimeter of the screen without expanding the central area.
PIP (Picture In Picture )
Function to enable the simultaneous viewing of two pictures by displaying a small sub-frame within the
main picture. The main picture may be viewed with multiple types of input source (Analog/Digital RGB,
composite, S-Video, component), while the sub-frame is only available in composite, S-Video or
component (480i).
PBP (Picture By Picture) ,Twin Picture
Function to assign two separate signals onto a single screen, thereby enabling the viewer to
simultaneously watch different pictures on each half of the display.
PIP Swap Simultaneous Conversion Between Sub and Main Pictures.
Function to convert between the sub-frame and main picture being watched simultaneously.
PIP Sound Swap Simultaneous Conversion Between sub and Main Picture Audio
Function to convert between simultaneous audio streams from the sub-frame and main picture being
viewed.
BSV-4251/4251A RD(1) 00 03/10/23 32/75

EQUALIZER
Function to control sound according to frequency. (100Hz, 300Hz, 1KHz, 3KHz, 10KHz)
AVL (Auto Volume Leveler)
Function to automatically adjust varying sound levels from each individual broadcasting company to an
appropriate volume, in case of watching a television connected to external equipment. This allows to
viewer to enjoy a comfortable and stable sound level even when changing the channel.
CIRCUIT OPERATION & WAVEFORM
VPC3230D (Video Processor)

BSV-4251/4251A RD(1) 00 03/10/23 33/75

Converts analog pictures (including Composite, S-Video, Component (480i) or the like) to Y-UV
digital pictures. Compatible with various TV formats of NTSC, PAL, SECAM, etc.
U41 (VPC323OD)_#28_S-LLC1 U42 (LM2937-3.3V)_#3_V3.3
LC18 (STS104B)_#2_VAA3230 U40 (LM2937-3.3V)_#3_V3.3V-1
BSV-4251/4251A RD(1) 00 03/10/23 34/75

LC16 (STS104B)_#2_VAA3230_1 U41 (VPC3230D)_#28_VID_CLK
U41 (VPC3230D)_#53_INTLC U41 (VPC3230D)_#57_VID-VS
U41 (VPC3230D)_#56_VID-HS
BSV-4251/4251A RD(1) 00 03/10/23 35/75

AD9883 (A/D Converter)
Converts an analog RGB signal to a process able digital signal. Converts a component signal (480p,
720p, 1080i) to a digital signal and transmits it to PW565 (Scaler).
U2 (AD9883)_#30_ Hsync0 U2 (AD9883)_#31_Vsync0
U2 (AD9883)_#67_DATACK U2 (AD9883)_#64_VSOUT
U2 (AD9883)_#65_SOG U2 (AD9883)_#66_HSOU T
BSV-4251/4251A RD(1) 00 03/10/23 36/75

U1 (LM2937)_#3_ VO
PW565 (Scaler)
BSV-4251/4251A RD(1) 00 03/10/23 37/75

Receives, at the same time, a video signal from VPC3230, an Analog/Digital RGB signal and a
Component signal, which are converted at AD9883 and THC63DV151, adjusted to a PDP display,
and transmitted to a PDP module. In particular, it receives any PC signal input at various scanning
rates and performs scaling to adjust to PDP resolution.
RP12 (R-ARRAY)_#1_DEN RP12 (R-ARRAY)_#4_DCLK
RP12 (R-ARRAY)_#3_DVS RP12 (R-ARRAY)_#2_DHS
MSP3450 (Sound Processor)
BSV-4251/4251A RD(1) 00 03/10/23 38/75

Receives and converts any Sound IF signal from a TV Tuner to a general audio signal (LCD TV).
Also, outputs the desired input signal out of many audio input signal options, and produces a woofer
signal or Headphone signal as well as a general Speaker signal (LCD TV).
U45 (MSP3450)_#65_AVSUP U43 (KIA7808AF)_#3_8V-Output
U45(MSP3450)_#36¡±_Audio R-Out U45(MSP3450)_#36¡±_Audio L-Out
Power & MISC Waveform
BSV-4251/4251A RD(1) 00 03/10/23 39/75

LC20 (STS104B)_#2_C344_5VST LC21 (STS104B)_#2_C353_5VDD
U15 (RC1117_3.3V)_#2_VCC3 L10 (33uH)_#2_R410_VCC12
Q33 (MMBT3904)_¡±C¡±_RL_ON Q30 (MMBT3904)_¡±C¡±_VAVS_ON
BSV-4251/4251A RD(1) 00 03/10/23 40/75

MODULE SUPPLY VOLTAGE SEQUENCE

[PDP42V5####]
¡Ü Life Expectancy
The anticipated life-time is estimated more than 25,000 hours of continuous operations .
¡Ø Average life time is the time when the brightness level becomes half of its initial value.
BSV-4251/4251A RD(1) 00 03/10/23 41/75

VSC POWER SEQUENCE
Display Enable
Relay On
VaVs On
1. After Relay On
• 2. Continue 5Volt Monitoring – If there is no 5Volt more than 10 minutes, then
• power “Off”
• 3. Check if it is OK the 5Volt Mnt first. And then VaVs “On” after 3 seconds .
• 4. VaVs “On” --> waiting 3 seconds --> Display Enable “On”.
5. If 5Volt Mnt “Low” or AC-Det “Low”, immediately Display Enable “Off” and
then VaVs “Off”, Relay “Off”.
BSV-4251/4251A RD(1) 00 03/10/23 42/75

PSU POWER SEQUENCE
[POWER DGK-420W]
BSV-4251/4251A RD(1) 00 03/10/23 43/75

VOLTAGE & W/B ADJUSTMENT
Power PCB Assy Voltage Adjustment
1-1-1. Va Adjustment (Address Voltage Adjustment)

(°¡) Connect pin 9,10 of CN806 to(+) jack of D.M.M
(³ª) After turning the VR2 (Va Adj),Voltage of D.M.M adjustment as same as Va voltage which on
Label of panel right/bottom.(Deviation : ± 0.5V)
1-1-2. Vs Adjustment
(°¡) Connect pin 1~3 of CN806 to (+) jack of D.M.M
(³ª) After turning the VR3(Vs Adj),voltage of D.M.M adjustment as same as Vs voltage which
indicated on Label of panel right/bottom.(Deviation : ± 0.5V)
Refer to Typical Voltage

1. Va : 65V
2. Vs : 190V
¡Ø Replace PDP Module or Power Board, adjust certainly Power PCB Ass’y Voltage
BSV-4251/4251A RD(1) 00 03/10/23 44/75

BSV-4251/4251A RD(1) 00 03/10/23 45/75

2. W/B adjustment
2-2. Color temperature (White Balance) adjustment
1) How to enter Factory mode for adjustment of White Balance

(1) PDP TV Power ¡°On¡± --> Input select key on Remote control.
(2) Choose composite first and then PDP TV Power ¡°Off¡±.
(3) PDP TV Power ¡°Off¡± and INFO on the R/C ==> ERASE ==> ENTER Key
2) For COMPOSITE adjustment (manual adjustment)
(1) Signal Generator supply the pattern of above picture. (Timing ¢¡ 386, Pattem ¢¡ 10)
(2) After movement to 2.color control on Factory Mode2, move to sub menu as choice of volume
button .
(3) After check the Brightness ¢¡ 50, Contrast ¢¡ 90, choose the Sub-Brightn ess.
(4) Zero calibration¡¯s execution of CA-100 and the sensor should be closed to surface of PDP
module.
(5) Adjustment as choice of volume button in order that it becomes Y= 6.0 ¡¾0.5 cd/m©÷ on the sub
brightness.
(6) Color coordinates¡¯ adjustment of Red Offset, Green Offset, Blue Offset using this kind of metho d.
Color coordination ¢¡ x= 0.281 ¡¾0.007, y=0.295 ¡¾0.007, Y= 6.0 ¡¾0.5 cd/m©÷
(Color temperature : 9500° K ¡¾ 500°K)
(7) The Sub-Brightness¡¯ readjustment when it is not satisfied with brightness after adjustment.
3) For DTV adjustment
BSV-4251/4251A RD(1) 00 03/10/23 46/75

(1) Signal Generator supply the pattern of above picture.

Timing ¢¡ 395, Pattem ¢¡ 251, Reverse (720P, 60Hz)
(2) After movement to 1.calibration on Factory Mode, move to sub menu as choice of volume button.
(3) After movement to 2. DTV Calibration, choose it with volume button.
(4) If Enter key, it starts the calibratio
4) For PC adjustment
BSV-4251/4251A RD(1) 00 03/10/23 47/75

(1) Signal Generator supply the pattern of above picture.

Timing ¢¡ 313, Pattem ¢¡ 609 (1024 x 768, 60Hz)
(2) After movement to 1.calibration on Factory Mode, move to sub menu as choice of volume
button .
(3) After movement to 2. PC Calibration, choose it with volume button.
(4) If Enter key, it starts the calibration automatically
How to exit the Factory Mode

INFO ¢¡ LAST ¢¡ ERASE ¢¡ ENTER Key
5) Adjustment verification
Adjustment as volume ¡°0¡± and then 4 times of Enter key
BSV-4251/4251A RD(1) 00 03/10/23 48/75

SAFETY PRECAUTIONS
( MODULE USE AND CONSIDERATIONS IN SERVICING)
PDP Module is a display device to be divided into a Panel part and a Drive part. The Panel part consists of
Electrodes, Phosphor, various dielectrics and gas, and the Drive part includes electronic circuitry and PCB.
When using / handling this PDP Module, pay attention to the below warning and cautions.
Indicates a hazard that may lead to death or injury if the warning is ignored and the product is handled
incorrectly.
Indicates a hazard that can lead to injury or damage to property if the caution is ignored and the product is
handled incorrectly.
■. WARNING
(1) Do not supply a voltage higher than that specified to this product. This may damage the product and may
cause a fire.
(2) Do not use this product in locations where the humidity is extremely high, where it may be splashed with
water, or where flammable materials surround it.
Do not install or use the product in a location that does no satisfy the specified environmental conditions.
This may damage the product and may cause a fire.
(3) If a foreign substance (such as water, metal, or liquid) gets inside the product, immediately turn off the
power.
Continuing to use the product, it is may cause fire or electric shock.
(4) If the product emits smoke, and abnormal smell, or makes an abnormal sound, immediately turn off the
power.
Continuing to use the product, it may cause fire or electric shock.
(5) Do not disconnect or connect the connector while power to the product is on. It takes some time for the
voltage to drop to a sufficiently low level after the power has been turned off.
Confirm that the voltage has dropped to a safe level before disconnecting or connecting the connector.
(6) Do not pull out or insert the power cable from/to an outlet with wet hands. It may cause electric shock.
(7) Do not damage or modify the power cable. It may cause fire or electric shock.
(8) If the power cable is damaged, or if the connector is loose, do not use the product: otherwise, this can
lead to fire or electric shock.
(9) If the power connector or the connector of the power cable becomes dirty or dusty, wipe it with a dry cloth.
Otherwise, this can lead to fire.
(10) PDP Module uses a high voltage (Max.450V dc). Keep the cautions concerning electric shock and do
not touch the Device circuitry when handling the PDP Unit. And because the capacitor of the Device
circuitry may remain charged at the moment of Power OFF, standing by for 1 minute is required in order
to touch the Device circuitry.
BSV-4251/4251A RD(1) 00 03/10/23 49/75

CAUTIONS
(1) Do not place this product in a location that is subject to heavy vibration, or on an unstable surface such as
an inclined surface. The product may fall off or fall over, causing injuries.
(2) Before disconnecting cable from the product, be sure to turn off the power. Be sure to hold the connector
when disconnecting cables. Pulling a cable with excessive force may cause the core of the cable to be
exposed or break the cable, and this can lead to fire or electric shock.
(3) This product should be moved by two or more persons. If one person attempts to carry this product alone,
he/she may be injured.
(4) This product contains glass. The glass may break, causing injuries, if shock, vibration, heat, or distortion
is applied to the product.
(5) The temperature of the glass of the display may rise to 80°C or more depending on the conditions of use.
If you touch the glass inadvertently, you may be burned.
(6) If glass surface of the display breaks or is scratched, do not touch the broken pieces or the scratches with
bare hands. You may be injured.
(7) PDP Module requires to be handled with care not to be touched with metal or hard materials, and must
not be stressed by heat or mechanical impact.
(8) There are some exposed components on the rear panel of this product. Touching these components may
cause an electric shock.
(9) When moving the product, be sure to turn off the power and disconnect all the cables. While moving the
product, watch your step. The product may be dropped or all, leading to injuries of electric shock.
(10) In order to protect static electricity due to C-MOS circuitry of the Drive part, wear a wrist band to protect
static electricity when handling.
(11) If cleaning the Panel, wipe it with a soft cloth moistened with water or a neutral detergent and squeezed,
being careful not to touch the connector part of the Panel. And don’t use chemical materials like thinner
or benzene.
(12) If this product is used as a display board to display a static image, “image sticking” occurs. This means
that the luminance of areas of the display that remain lit for a long time drops compared with luminance
of areas that are lit for a shorter time, causing uneven luminance across the display.
The degree to which this occurs is in proportion to the luminance at which the display is used. To prevent
this phenomenon, therefore, avoid static images as much as possible and design your system so that it
is used at a low luminance, by reducing signal level difference between bright area and less bright area
through signal processing.
(13) Because PDP Module emits heat from the Glass Panel part and the Drive circuitry, the environmental
temperature must not be over 40°C.
The temperature of the Glass Panel part is especially high owing to heat from internal Drive circuitry. And
because the PDP Module is driven by high voltage, it must avoid conductive materials.
(14) If inserting components or circuit board in order to repair, be sure to fix a lead line to the connector
before soldering.
BSV-4251/4251A RD(1) 00 03/10/23 50/75

(15) If inserting high-power resistor(metal-oxide film resistor or metal film resistor) in order to repair, insert it
as 10mm away as from a board.
(16) During repairs, high voltage or high temperature components must be put away from a lead line.
(17) This is a Cold Chassis but you had better use a cold transformer for safety during repairs. If repairing
electricity source part, you must use the cold transformer.
(18) Do not place an object on the glass surface of the display.

The glass may break or be scratched.
(19) This product may be damaged if it is subject to excessive stresses (such as excessive voltage, current,
or temperature).
The absolute maximum ratings specify the limits of these stresses.
(20) The recommended operating conditions are conditions in which the normal operation of this product is
guaranteed. All the rated values of the electrical specifications are guaranteed within these conditions.
Always use the product within the range of the recommended operating conditions. Otherwise, the
reliability of the product may be degraded.
(21) This product has a glass display surface. Design your system so that excessive shock and load are not
applied to the glass. Exercise care that the vent at the corner of the glass panel is not damaged.
If the glass panel or vent is damaged, the product is inoperable.
(22) Do not cover or wrap the product with a cloth or other covering while power is supplied to the product.
(23) Before turning on power to the product, check the wiring of the product and confirm that the supply
voltage is within the rated voltage range. If the wiring is wrong or if a voltage outside the rated range is
applied, the product may malfunction or be damaged.
(24) Do not store this product in a location where temperature and humidity are high. This may cause the
product to malfunction. Because this product uses a discharge phenomenon, it may take time to light
(operation may be delayed) when the product is used after it has been stored for a long time. In this case,
it is recommended to light all cells for about 2 hours (aging).
(25) This product is made from various materials such as glass, metal, and plastic. When discarding it, be
sure to contact a professional waste disposal operator.
(26) If faults occur due to arbitrary modification or disassembly, Erae Electronics is not responsible for
function, quality or other items.
(27) Use of the product with a combination of parameters, conditions, or logic not specified in the
specifications of this product is not guaranteed. If intending to use the product in such a way, be sure to
consult Erae Electronics in advance.
(28) Within the warranty period, general faults that occur due to defects in components such as ICs will be
rectified by Erae Electronics without charge. However, IMAGE STICKING due to misapplying the above
(12) provision is not included in the warranty. Repairs due to the other faults may be charged for
depending on responsibility for the faults.
BSV-4251/4251A RD(1) 00 03/10/23 51/75

BSV-4251/4251A RD(1) 00 03/10/23 52/75

TROUBLE SHOOTING
1. Checking for no Picture

A screen doesn if display at all and condition of black pattern or power off.
(1) Check whether the CTRL B/D LED(D1~D4) is turned on or not.

(2) Check the power and signal cable of CTRL B/D.
(3) X B/D, Y B/D, Z B/D is well plugged in.
(4) Check the connection of X B/D, Y B/D and Z B/D to CTRL B/D.
(5) Measure the output wave of X, Y, Z B/D with oscilloscope(more than 200MHz)
and find the trouble of B/D by comparing the output wave with below figure.
- Measure Point fo Y B/D : TP (Connector P4 80 pin)
- Measure Point fo Z B/D : Connection part of panel (SUS_OUT)
- Measure Point fo X B/D : L1(RIGHT), L2(LEFT BOTTOM)
(6) Check the SCAN(Y side) IC
(7) Check the DATA(X side) COF IC
(8) Replace the CTRL B/D.
2. Hitch Diagnosis Following Display Condition
2-1. 4/7 or 3/7 of the screen doesn’t be shown
(1) Confirm the power connector of X B/D is well plugged in which is correspond to not showing screen.
(2) Confirm the connector that is connected between CTRL B/D and X B/D correspond to not showing
part.
(3) Replace relevant X B/D.
Relationship between screen and X B/D
Display X B/D
Left of the Screen 4/7 Right X B/D
Right of the Screen 3/7 Left X B/D
BSV-4251/4251A RD(1) 00 03/10/23 53/75

¡Ø Screen Display Form
2-2. The screen doesn’t be shown as Data COF

(Include not be shown part of Data COF quantity or a part)
(1) The problem between Data COF and X B/D is more possible that the screen is not be shown as data
COF.
(2) Confirm the connector of Data COF is well connected to X B/D. Correspond to the part that screen is
not showing
(3) Confirm whether the Data COF is failed and replace X B/D
※ Example of the screen display form

(Anything of the 7 Data COF can be shown beside below pictures)
※ How to examine Data COF IC
BSV-4251/4251A RD(1) 00 03/10/23 54/75

2-3. It Generates Unusual Pattern of Data COF IC unit

(1) In case of generating unusual pattern of Data COF IC unit as below picture, there is problem in the check
that is input into Data COF IC
(2) In case of <case 1, 2, 3>

- confirm the connection of Data COF connector
- replace the relevant X B/D
(3) In case of <case 4, 5>

- confirm the connector that is connected from CTRL to X B/D
- Replace relevant XB/D or CTRL B/D
※ Screen Display Form

BSV-4251/4251A RD(1) 00 03/10/23 55/75

2-4. Regular Stripe is Generated about the Quantity of one Data COF IC or more
(1) In case of generating regular stripe about the quantity of one Data COF IC, there is problem at the
output of outputflatworm of X B/D
In case of generating regular stripe about the quantity of two Data COF IC, that means the data
which is conveyed from CTRL B/D doesn’t conveyed well.
(2) Confirm the XB/D connection connector plugged in well.

Correspond to unusual screen.
(3) Replace relevant XB/D or CTRL B/D.
※ Relationship between screen and X B/D
BSV-4251/4251A RD(1) 00 03/10/23 56/75

Display X B/D
Left Bottom of the Screen 4/7 Right X B/D
Right Bottom of the Screen 3/7 Left X B/D
2-5. The screen display has a problem for Scan FFC.

(1) It’s may be a problem between Scan FFC and Y B/D.
(2) Check the connection of Y B/D and Scan COF.
(3) If the Scan IC is failed, replace the Y DRV B/D.
. Screen Display Form
※ Check a method of SCAN IC
BSV-4251/4251A RD(1) 00 03/10/23 57/75

2-6. The screen has a vertical line with regular gap.

(A vertical stripe flash at especial color)
(1) This is a problem about control B/D.
(2) Replace Control B/D.
2-7. A data copy is happened into vertical direction
BSV-4251/4251A RD(1) 00 03/10/23 58/75

(1) In this case, it’s due to incorrect marking of scan wave.

(2) Replace a Y DRV B/D or Y SUS B/D.
2-8. The screen has one or several vertical line

(1) In this case, It isn’t a problem about controller B/D or X B/D.
(2) It may cause followings.
- It’s out of order a panel
- Open or short of DATA COF FPC attached panel
- It’s out of order a DATA COF attached panel
(3) Replace Module.
2- 9. The screen has one or several horizontal line

(1) In this case, it isn’t a problem about controller B/D or X B/D.
BSV-4251/4251A RD(1) 00 03/10/23 59/75

(2) It may cause followings.

- It’s out of order a panel
- Open or short of SCAN FPC attached panel
- It’s out of order a SCAN IC attached panel
(3) Replace Y DRV B/D
2-10. The screen displays input signal pattern but the brightness is dark
(1) In this case, Z B/D operation isn’t complete.
(2) Check the power cord of Z B/D.
(3) Check the connector of Z B/D and Controller B/D.
(4) Replace the Controller B/D or Z B/D.
2-11. The screen displays other color partially on full white screen or happens
discharge partially on full black screen.
(1) Check the declination of Y B/D set up, set down wave.
(2) Check the declination of Z B/D ¢«ramp wave.
(3) Measure each output wave with oscilloscope(more than 200MHz) and compare the data with below
figure data.
Adjust the Y B/D set up(Test-up:B/C[¥s/¥s])/setdown(Testdown: D[¥s]) and Z B/D
ramp(Tramp:F/G[¥s/¥s]) declination by changing VR1/VR2/VR3.
- Measuring Point of Y B/D : P4 (Connector P4 36 pin)
- Measuring Point of Z B/D : B37 (SUS_OUT)
2-12. A center of screen is darker than a edge of screen at full white pattern.
(1) In this case, it’s a problem about Z B/D ramp wave.
(2) Check the connection cable of Z B/D and CTRL B/D.
BSV-4251/4251A RD(1) 00 03/10/23 60/75

(3) Replace the Z B/D.
2-13. It doesn’t display a specified brightness at specified color

(1) Check the connector of CTRL B/D input signal.
(2) Replace the CTRL B/D.
3-1. No Power
Nothing output
of image.
BSV-4251/4251A RD(1) 00 03/10/23 61/75

Check Input of AC Abnormal Connect plug with the set.

(90V ~225V)
Normal
Check ST-BY LED ON Abnorma l

Main S/W ON. Check AC Line Fuse
Normal
Check LED YELL OW Abnormal Check OPEN With Abnormal Replace

Sub S/W ON CN806,CN13 IC15,IC16,Q30
Check the Vs Voltage
IC1 5,IC16(PSU Part)
and VSC Part Q30
Shor t
Normal
Check a connective condition

and various connect or.
3-2. No Sound
Check a connective Check voltage Check Open with Check connection

condition of power of sound terminal . FuseF1 Fuse line of speake r.
cable
3-3. No Video
Abnormal Picture
BSV-4251/4251A RD(1) 00 03/10/23 62/75

Check BA7657 Check AD9883

Input PC,DTV Signal Abnormal U2
U8
Normal
Abnorma l Check VPC3230 Dual

Input DV D Signal Check PW565
U39,U41
RP12~18
Normal
Abnormal Abnormal
Input Tuner-CVB S, Check CX A2089Q Check SiI164
CVBS,F/H SCART,S-Video U3 U48
Signal
Normal
Abnormal Check Cable
Input F/SCART RGB Check BA7657

Signal U28
3-4. No Sound
Check Check Check Check Check

co nnector CXA2089Q MSP3450G TDA7495S Input
Speaker t o U3 U45 U14 Jack.
set.
IMAGE STICKING CHARACTERISTICS

1) Image Sticking
The fluorescent substance used in the plasma module loses its brightness with the lapse of lighting time.
This deterioration in brightness apprears to be a difference in brightness in relation to the surroundings,
and cornes to be recognized as image sticking.
BSV-4251/4251A RD(1) 00 03/10/23 63/75

In other words, the image sticking is defined as follows: when the same pattern(of the fixed display)is
displayed for a long times, a difference in brightness is caused around the lighting area and non-lighting
area due to deterioration in the fluorescent substance.
When the present pattern is changed over to another one, the boundary comes to be seen between the
lighting area and non-lighting area due to difference in brightness in the pattern shown shorty before
changeover. If this conditions is accumulated, the boundary or image sticking comes to be seen with the
naked eyes.
2) Secular change in brightness

The life of brightness, defined as the reduction to half the initial level, is more than 25 thousand hours on
average.
Conditions: All white (100% white) input at an ambient temperature of 25℃.
However, this lifetime is not a guarantee value for life and brightness. It should be recognized simply as
the data for refernce.
3) Warrenty
Image sticking and faults in brightness and picture elements are excluded from the warranty objects.
4) Cause of deterioration in brightness

A major possible cause of deterioration in brightness is damage in the fluorescent substance due to
impact caused by ions generated at the time of plasma discharges.
5) Practical value for Image sticking

The relationship between intergrated lighting time and brightness in this plasma module is described in
the attached material. In particular, the deterioration in brightness tends to be accelerated up to 100
hours in the initial period. In the initial period, the fixed display of patterns particularly tends to cause
image sticking. The practical value for image sticking is difficult in concrete numerals. As described
below, you are advised to take proper measures to make the occurrence of image sticking as slow
possible.
6) Proposed measures taken to relieve image sticking

So long as there is the reduction of brightness in the fluorescent substance, it is impossible to the avoid
the occurrence of image sticking .Therefore, to relieve image sticking ,we offer you a method of entering an
image input that may ensure reluctance to the generation of the difference in brightness reduction among
the displayed dots.
The images from TV broadcasting involve a high rate of motion picture displays. Therefore, there is less
change of being a cause of difference in brightness reduction among the cells. Even when the fixed
patterns are displayed, they generally last for a few minutes. Since the same pattern is less liable to be
displayed, there is almost no influence toward image sticking.
If the fixed patterns tend to be displayed for a long time, however, there occurs a substantial imbalance
between the lighting and non-lighting areas, this causing a difference in brightness as a result. In this
document , we offer you some proposals of installation, paying attentions to the two points: the reduction of
difference of brightness achieved by intergrated lighting time leveling and the method of edge smearing to
make image sticking hard to be discerned.
The result from these proposals can, however, greatly depend on the contents of images and operating
environment.
Therefore, we consider that it is essential to take the suitable measures in consideration of the customer’s
operating environment.
Example of Poposal 1: The display position is moved while the fixed display pattern is changed over, or it is
scrolled during the display.
Example of Proposal 2: If possible, a pattern of complementary color is incorporated (for intergrated time
leveling).
Example of Proposal 3: The fixed pattern and the motion picture display are reciprocally exchanged, in
BSV-4251/4251A RD(1) 00 03/1 0/23 64/75

order to minimize display period of the fixed pattern.
Example of Proposal 4: During operation, the brightness of screen is suppressed as low as possible.
For the display patterns, characters are indicated not on the black ground (non-picture area) but on the
colored ground (mixture of R, G,B recommended).
ISM Mode(Image Sticking Minimization Mode)
Apart from the above proposal, This module has been equipped with a special method that minimizes the
image sticking phenomenon. When in the fixed pattern display mode, the module decreases the brightness
over a period of 10 minutes with small steps. The figure blow shows that the decrease in brightness is so
small the user will not notice.
BSV-4251/4251A RD(1) 00 03/10/23 65/75

The basis of the evaluation was while the ISM Mode in the module was operating, the brightness decrease
about
55 % of its initial value at the white window pattern ( 1/25 of full white pattern )
ISM operational conditions
1. Detective deviation : The change of APL Data is no less than ±4 and it will remain for more than 5
minutes.
2. Regardless of time, it will not operate where the display load is over 50%.
SCHEMATIC & PRINTED CIRCUIT BOARD & EXPLODE VIEW

¡á PSU(DGK-420W) TOP
BSV-4251/4251A RD(1) 00 03/10/23 66/75

■ PSU(DGK-420W) BOTTOM
BSV-4251/4251A RD(1) 00 03/10/23 67/75

EXPLODED VIEW PARTS LIST

No Part no Description
BSV-4251/4251A RD(1) 00 03/10/23 68/75

2 S150110021 MAIN ASSY EPT-4200A(PAL)
3 S15012G021 FRONT FRAME ASSY EPT-4200A(PAL-STD)
4 S15013F016 FRAME FILTER ASSY EPM-4200A(MONITOR-STD)
5 S15014B016 FRAME ASSY EPM-4200B(MONITOR-STD)
2 S15012C021 JACK HOUSING ASSY EPT-4200(PAL)
4 S15014A021 FRONT ASSY EPT-4200A(PAL)
3 S15013C016 HEAT SINK ASSY EPM-4200A
3 S15013B016 MODULE ASSY EPM-4200A
2 S15012F016 AC IN-LET ASSY EPM-4200A
3 S150120036 VSC BOARD ASSY(TOP) EPT-4200AP
2 S150113036 VSC BOARD ASSY EPT-4200AP(PW565)
4 S150130036 VSC BOARD ASSY(BOTTOM) EPT-4200AP
6 S15015B021 OSD PCB ASSY EPT-4200A(TV用_7KEY)
2 S150114036 TUNER BOARD ASSY EPT-4200AP(PW565)
3 S150121036 TUNER BOARD ASSY(SMD) EPT-4200AP(PW565)
2 S150134021 AUDIO OUT B/D ASSY EPM4200A
2 S150112021 POWER S/W ASSY EPT-4200A(PAL-STD)
3 S150132009 POWER S/W PCB ASSY EPM-420AN
5 S150141021 OSD ASSY EPT-4200A(TV用_7KEY)
1 S150111021 PACKING ASSY EPT-4200A(PAL)
2 S15012F021 ACCESSORY ASSY EPT-4200A(PAL)
3 S15013C021 REMOCON ASSY EPT-4200A(PAL)
3 71BELP324 JACK HOUSING AL/PAL TV
3 71BELP315 HEAT SHINK AL 28X28X13
4 71BELP1801 HEAT SINK ASSY AL+SPTH
3 71FELP314 SHIELD VSC-B SPTH-C, 0.5T
2 71FELP313 SHIELD VSC-T SPTH-C, 0.3T
2 70AELM310 BUTTON POWER ABS
2 71AELP126 BRKT SUPP EGI/1T
2 71AELP288 BRKT A EGI/1T
2 71AELP289 BRKT B EGI/1T
2 71AELP310 BRKT IN-LET EGI/1T
2 71AELP311 BRKT VSCEGI/1T
2 71BELP287 BACK AL 1.5T PAINT/KK VERSION
6 71AELP115 BRKT STAND EGI 1.5T
6 71AELP118 BRKT C EGI 1T
6 71AELP284 BRKT D EGI/1T/EPM-420KK
5 71AELP117 BRKT FILTER EGI 1T
6 77A1010540 BLACK SH B FELT 1TX10X540
6 77A1010950 BLACK SH A FELT 1TX10X950
6 71BELP285 FRAME X AL
6 71BELP286 FRAME Y AL
5 70EELM311 LENS PMMA
5 70PELM3298 FRONT A PC/ABS/SILVER/DCDI/STAND BY/7KEY/EPM-4200A
5 72BELR111 PROTECTOR SILICON/25X25X45
6 70AELM460 BUTTON CTRL ABS(7KEY)/EPT-4200(TV用)
6 73DELi046 INSULATION-BUTTON PVC(25X15X0.3T)
7 70AEPM1173 LED GUIDE 4MMX5ΦX3P
4 71HELP246 SUPPORT Y SPC, 1.6t
4 70AELM310 BUTTON POWER ABS
BSV-4251/4251A RD(1) 00 03/10/23 69/75

4 71AELP125 BRKT PW EGI 1T
4 73DELi032 INSULATION SW PC 0.5tX70X53
4 AJ-00003 SNAP RIVET DASR 470
3 74B2BN3008FB T/SCREW BH T 3X8 2S ZB
2 74B2BN3005FW T/SCREW BH T 3X5 2S ZW
2 74B2BN3008FB T/SCREW BH T 3X8 2S ZB
4 74B2PN4010FW T/SCREW PH T 4X10 2S ZW
5 74B2BN3010FB T/SCREW PH T 3X10 2S ZB
4 74B2BN3008FW T/SCREW BH T3X8 2S ZW
4 74A2BZ3006FY M/SCREW BH M 3X6 ZN
2 74A2FN3008FB M/SCREW FH M 3X8 ZB
2 74A9BZ3008FB M/SCREW BH M 3X8 ZB
2 74GELC0015 À°°¢º¼Æ® 15"°ø¿ë
2 74GELM006 CHAMFER SCREW TH M 4X8 ZB
2 74GELM007 CHAMFER SCREW PH M 3X10 SPRING WASHER(φ8)
4 74GELM006 CHAMFER SCREW TH M 4X8 ZB
3 74GELM007 CHAMFER SCREW PH M 3X10 SPRING WASHER(φ8)
2 74GELM008 GRAOUND SCREW PH M 4X10 (SPECIAL)
3 76AZW15D42D15 WASHER SPCC 15X4.2X1.5T ZW
2 50-0007 WIRE ASSY AUDIO OUT 4P EPM-420
2 50-0074 WIRE ASSY AUDIO POWER 4P 250mm
2 50-0075 WIRE ASSY A/D POWER SOURCE 12P 210mm
2 50-0077 WIRE ASSY AC POWER 2P 430mm
2 50-0089 WIRE ASSY OSD 13P 690mm
2 50-0103 WIRE ASSY A/D CONTROL 7P 220mm
2 50-0104 WIRE ASSY PANEL LINK 21P 270mm
2 50-0108 WIRE ASSY FFC 24P 280mm
4 65-0024 PDP MODULE PDP42V51000(42"PDP MODULE)
5 79FELG0013 FILTER GLASS 1142G03E/45%/972X660X3.8T
3 66-0020 TUNER TCPQ9091PD27D(S)
2 66-0049 FAN H35094-57ERA
7 31-0167 PCB E83-U005-02-PB00 REV.00 OSD 7KEY
3 31-0162 PCB E83-U005-00-PB00 REV.00(PAL_VSC)
4 31-0163 PCB E83-U006-11 PB00 REV.00 (PAL_TUNER)
3 31-0146 PCB E83-U004-07-PB00 REV.00 (Audio Out)
4 31-0036 PCB PB-001E EPM420 AC POWER REV.00
2 72SELM044 ACEET TAPE 10X60
2 73DELi051 INSULATION-PS PC,0.45TX80X125
2 73DELi054 INSULATION TN PVC 0.25TX232X342
2 AL-00001 CABLE TIE DACT-100(140mm)
2 AL-00022 수축튜브 φ13X0.15X14mm/F4(Z)
REPLACEMENT PARTS LIST(PAL TV)
BSV-4251/4251A RD(1) 00 03/10/23 70/75

No Part no Description
IC
4 01-0019 IC REG LM2937IMP-3.3 SOT-223
4 01-0020 IC REG LM317EMP SOT-223
4 01-0059 IC REG RC1117S33 SOT-223
4 01-0071 IC REG KIA7809AF D-PAK
4 01-0273 IC REG NCP1117ST18T30
4 01-0040 IC EEPROM 24LC16B SOP-08
4 01-0041 IC EEPROM 24LC21A SOP-08
4 01-0053 IC TTL 74LCX14M SOP-14
4 01-0055 IC TTL SN74LV273A SOP-20
4 01-0057 IC TTL SN74LVC541A SOP-20
4 01-0225 IC MCU HMS87C1102AD SOP-16
4 01-0091 IC TDA7495S MULTI-WATT 15V ST
4 01-0073 IC K4S643232E TSSOP(II)
4 01-0108 IC DS232AS SO-16
4 01-0253 IC VPC3230D-C5 PQFP-80
4 01-0259 IC FDC6561AN-Super SOT-6
4 01-0260 IC MSP3450G PQFT-80
4 01-0261 IC SST39VF080AT-TSOP40
4 01-0262 IC SDA5550 M 3901.A14 9RF
4 01-0263 IC HY62U8200BLLST-85I sTSOP
4 01-0264 IC CXA2089Q
4 01-0265 IC SiI164CT64
4 01-0266 IC BA7657-SOP24
4 01-0278 IC AD9883AKST-140
4 01-0282 IC 24LC256-SOIC8
4 01-0283 IC AP1084K18-TO263
4 01-0284 IC PW565_10Q_BGA
4 01-0285 IC MT28F800B3WG-9T
4 01-0286 IC SN74LVC139AD-SOIC16
4 01-0287 IC SN74LVX74AD-SOIC14
4 01-0288 IC TLC7733QD SOIC-08
3 01-0092 IC ZJY51R5-4P(EMI)
7 33-0003 IR RECEIVER KSM-603LM2(Straight)
TRANSISTOR
4 02-0012 TR MMBT3904 SOT-23
4 02-0025 TR KTC3875Y SOT-23
4 02-0038 TR KSC1623Y
5 02-0012 TR MMBT3904 SOT-23
5 02-0025 TR KTC3875Y SOT-23
DIODE
4 04-0005 DIODE BAV99 SOT-23
4 04-0054 DIODE KDS184
4 04-0058 DIODE ZENER Z02W18V-Y
4 04-0030 DIODE ZENER Z02W3.3 SOT-23
BSV-4251/4251A RD(1) 00 03/10/23 71/75

4 04-0128 DIODE KDZ8.2EV-RTK
5 04-0127 DIODE 1SR154-400
4 04-0128 DIODE KDZ8.2EV-RTK
3 04-0038 DIODE 1N4004 TP
7 04-0033 LED SAM3270
4 04-0053 LED SR2333-H SOT-23
CAPACITOR
4 10-0009 CC CHIP 25V 330J 1608 TP
4 10-0016 CC CHIP 16V 224Z 1608 TP
4 10-0017 CC CHIP 16V 474Z 1608 TP
4 10-0021 CC CHIP 25V 102K 1608 TP
4 10-0022 CC CHIP 25V 103Z 1608 TP
4 10-0023 CC CHIP 25V 104Z 1608 TP
4 10-0024 CC CHIP 25V 180J 1608 TP
4 10-0028 CC CHIP 25V 393K 1608 TP
4 10-0029 CC CHIP 25V 473K 1608 TP
4 10-0053 CC CHIP 25V 392K 1608 TP
4 10-0054 CC CHIP 25V 331J 1608 TP
4 10-0057 CC CHIP 10V 684Z 1608 TP
4 10-0058 CC CHIP 25V 200J 1608 TP
4 10-0059 CC CHIP 25V 471J 1608 TP
4 10-0060 CC CHIP 25V 334Z 1608 TP
4 10-0063 CC CHIP 25V 221J 1608 TP
4 10-0189 CC CHIP 25V 105Z 1608 TP
4 10-0197 CC CHIP 25V 682J 1608 TP
5 10-0004 CC CHIP 25V 101J 1608 TP
5 10-0016 CC CHIP 16V 224Z 1608 TP
5 10-0021 CC CHIP 25V 102K 1608 TP
10-0022 CC CHIP 25V 103Z 1608 TP
5 10-0023 CC CHIP 25V 104Z 1608 TP
5 10-0024 CC CHIP 25V 180J 1608 TP
5 10-0029 CC CHIP 25V 473K 1608 TP
5 10-0049 CC CHIP 25V 560J 1608 TP
5 10-0050 CC CHIP 25V 391J 1608 TP
5 10-0055 CC CHIP 25V 152K 1608 TP
5 10-0059 CC CHIP 25V 471J 1608 TP
5 10-0063 CC CHIP 25V 221J 1608 TP
5 10-0189 CC CHIP 25V 105Z 1608 TP
4 10-0004 CC CHIP 25V 101J 1608 TP
4 10-0023 CC CHIP 25V 104Z 1608 TP
3 10-0052 CC 400V SD222M
7 10-0051 CC 50V 104Z(AXIAL)
4 11-0044 EC SMD MV 16V 22UF (5X5.3) TP
4 11-0045 EC SMD MV 16V 10UF (4X5.3) TP
4 11-0046
4 11-0048 EC SMD MV 16V 100UF (6.3X5.3) TP
4 11-0049 EC SMD MV 16V 47UF (6.3X5.3) TP
4 11-0051 EC SMD MV 50V 3.3UF (4X5.3)TP
4 11-0055 EC SMD MV 50V 1UF (4X5.3) TP
4 11-0123 EC SMD MV 16V 33UF(6.3X5)TP
4 11-0146 EC SMD MV 16V 330UF (8X10)TP
BSV-4251/4251A RD(1) 00 03/10/23 72/75

4 11-0045 EC SMD MV 16V 10UF (4X5.3) TP
4 11-0048 EC SMD MV 16V 100UF (6.3X5.3) TP
4 11-0049 EC SMD MV 16V 47UF (6.3X5.3) TP
3 11-0054 EC SHL 50V 470UF (10X20)
7 11-0042 EC SRA 16V 47UF (6.3X7)
3 11-0010 EC SHL 16V 470UF (8X11.5)
3 11-0054 EC SHL 50V 470UF (10X20)
3 11-0148 EC KMG 50V 1000UF (12.5X25)
3 12-0003 PC PE 50V 104J RST
3 12-0004 PC 10PS 470MJ 12 (10X12.5)
4 13-0002 TC TAJB106M016R (16V 10UF)
JACK
3 53-0060 JACK PPJ122A-11
3 53-0064 JACK PPJ122-17(AUDIO JACK)
3 53-0068 JACK S 456S-J(CVBS)
3 53-0070 JACK PJ6046B-05
3 53-0055 JACK SCART JACK
3 52-0002 CONNECTOR DHR20-15K-7100 (15PIN D-SUB R/A)
3 52-0124 CONNECTOR MYD-09-2100010(9PIN D-SUB R/A)
3 52-0072 TERMINAL SP 026B
COIL,CORE,BEAD
4 16-0015 COIL 3.3UH (3216) 50MA
4 16-0016 COIL 10UH (10X10 SMD)1.
4 16-0017 COIL 33UH (12X12 SMD) 2.8A
7 16-0002 COIL 10UH (AXIAL)
2 17-0011 CORE ZCAT 1518-0730-M-K
4 17-0003 BEAD HB-1M2012-221JT
4 17-0004 BEAD HH-1M3216-121JT
4 17-0016 BEAD HB-1M2012-121JT
4 17-0023 BEAD HCB 4516K-600T60
4 17-0023 BEAD HCB 4516K-600T60
5 17-0023 BEAD HCB 4516K-600T60
RESISTOR
4 14-0001 R ARRAY 164P 000J TP
4 14-0003 R ARRAY 164P 470J TP
4 14-0007 R CHIP 1608 000J TP
4 14-0008 R CHIP 1608 101F TP
4 14-0010 R CHIP 1608 102F TP
4 14-0012 R CHIP 1608 103F TP
4 14-0022 R CHIP 1608 153F TP
4 14-0030 R CHIP 1608 202F TP
4 14-0043 R CHIP 1608 332F TP
4 14-0045 R CHIP 1608 333J TP
4 14-0050 R CHIP 1608 470F TP
4 14-0052 R CHIP 1608 472F TP
4 14-0069 R CHIP 1608 750F TP
4 14-0128 R CHIP 1608 222J TP
4 14-0175 R CHIP 1608 820J TP
4 14-0179 R CHIP 1608 152F TP
4 14-0268 R CHIP 1608 122J TP
4 14-0278 R CHIP 1608 241J TP
4 14-0289 R CHIP 1608 392J TP
4 14-0481 R CHIP 1608 511J TP
5 14-0007 R CHIP 1608 000J TP
5 14-0008 R CHIP 1608 101F TP
5 14-0010 R CHIP 1608 102F TP
5 14-0012 R CHIP 1608 103F TP
5 14-0022 R CHIP 1608 153F TP
5 14-0027 R CHIP 1608 181J TP
5 14-0029 R CHIP 1608 201F TP
BSV-4251/4251A RD(1) 00 03/10/23 73/75

5 14-0030 R CHIP 1608 202F TP
5 14-0034 R CHIP 1608 223F TP
5 14-0037 R CHIP 1608 271J TP
5 14-0043 R CHIP 1608 332F TP
5 14-0045 R CHIP 1608 333J TP
5 14-0050 R CHIP 1608 470F TP
5 14-0052 R CHIP 1608 472F TP
5 14-0055 R CHIP 1608 473J TP
5 14-0064 R CHIP 1608 562J TP
5 14-0066 R CHIP 1608 681J TP
5 14-0069 R CHIP 1608 750F TP
5 14-0107 R CHIP 1608 471F TP
5 14-0128 R CHIP 1608 222J TP
5 14-0175 R CHIP 1608 820J TP
5 14-0178 R CHIP 1608 220F TP
5 14-0179 R CHIP 1608 152F TP
5 14-0205 R CHIP 1608 683J TP
5 14-0268 R CHIP 1608 122J TP
5 14-0270 R CHIP 1608 131J TP
5 14-0321 R CHIP 1608 391F TP
5 14-0476 R CHIP 1608 474F TP
4 14-0008 R CHIP 1608 101F TP
4 14-0010 R CHIP 1608 102F TP
4 14-0012 R CHIP 1608 103F TP
4 14-0052 R CHIP 1608 472F TP
4 14-0055 R CHIP 1608 473J TP
4 14-0069 R CHIP 1608 750F TP
3 14-0181 R MOS 2W 470 J
SWITCH
7 22-0002 S/W TACT KLT-1105(4.3MM)
4 22-0013 S/W AC POWER SDDFC30300
FILTER & CRYSTAL

3 20-0004 FILTER LINE 4P(12MH)
4 20-0001 FILTER NOISE STS104B 2012.5 TP
5 20-0001 FILTER NOISE STS104B 2012.5 TP
3 60-0033 AC INLET ID-N10BEH(42")
3 19-0007 X-TAL 6.000MHZ
3 19-0009 X-TAL 20.000MHZ
3 19-0010 X-TAL 20.250MHZ 18PF
3 19-0011 X-TAL 18.432MHZ 18PF
3 30-0001 OSCILLATOR 80MHz(3.3V)
ACCESSORIES
3 27-0004 BATTERY AAA Type(¸Á°£)
3 55-0023 CABLE Scart Cable 1.2M
3 55-0024 CABLE RF-CABLE(PAL) 1P/2.1M
3 57-0130 P-CORD EL SALVADOR 115V/60HZ F ¿µ±¹Çâ G Type(57-0038)
3 92AELV0012 POLY BAG-M LDPE 0.08TX300X320
4 60-0031 REMOCON EPT-4200TV (PAL)
BSV-4251/4251A RD(1) 00 03/10/23 74/75

EXPLODE VIEW
BSV-4251/4251A RD(1) 00 03/10/23 75/75

TV Plasma Belson Bsv4251 Bsv4251a Daewoo Pds2950 Pds4250 Chassis Sp120 Firstline Ept3400 Ept4200ap LG Pdp42v5 Tatung Tpt4202s

Uploaded by

Copyright:

Available Formats

TV Plasma Belson Bsv4251 Bsv4251a Daewoo Pds2950 Pds4250 Chassis Sp120 Firstline Ept3400 Ept4200ap LG Pdp42v5 Tatung Tpt4202s

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TV Plasma Belson Bsv4251 Bsv4251a Daewoo Pds2950 Pds4250 Chassis Sp120 Firstline Ept3400 Ept4200ap LG Pdp42v5 Tatung Tpt4202s

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL (BSV-4251 BSV-4251A )

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 1/75

CONTROL DESCRIPTIONS …………………………………... 7

OPTIONS EXTRAS ..……………………..…………………… 9

REMOTE CONTROL BUTTONS ………..……………………. 10

DISPLAY CELL DEFECT SPECIFICATION …………………. 12

BLOCK & WIRING DIAGRAM …………………………………14

MODULE FUNCTION & DEFINITION ……………………….. 16

MODULE BASIC CONFIGURATION …………………….……17

VSC BOARD PIN CONFIGURATION …………….………….. 18

OSD MENU (FACTORY)……………………………………….. 21

DESCRIPTION OF VSC FUNCTIONS ……………………….. 32

CIRCUIT OPERATION & WAVEFORM……………………….. 34

MODULE SUPPLY VOLTAGE SEQUENCE …………………. 41

VSC & PSU POWER SEQUENCE ……………………….….... 42

VOLTAGE & W/B ADJUSTMENT……………………………… 44

SAFETY PRECAUTIONS …………………………………………49

BSV-4251/4251A RD(1) 00 03/10/23 2/75

IMAGE STICKING CHARACTERISTICS ……………………… 64

SCHEMATIC &PRINTED CIRCUIT BOARD &EXPLODE VIEW ……… 67

EXPLODED VIEW PARTS LIST ………………………………… 69

REPLACMENT PARTS LIST …………………………………….. 71

EXPLODE VIEW …………………………………………………… 75

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 3/75

2. Input Voltage : AC 100V ~ 240V,@ 50/60Hz, 4A

3. Power Consumption : 320W

4. PDP Module : PDP42V51000,51300(YBT), 51330(new ASIC) - LGE

6. Sound Output : 10W + 10W

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 4/75

ITEM MIN TYP MAX UNIT

2) COMPONENT Mode (Y,Cb/Pb,Cr/Pr)

RESOLUTION H-Freq(KHz) V-Freq(Hz) Proposed

3)SUPPORTIING DISPLAY Mode

RESOLUTION H-Freq(KHz) V-Freq(Hz)

10. RS-232C Signal

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 5/75

BSV-4251/4251A RD(1) 00 03/10/23 6/75

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 7/75

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 8/75

◐Contract your dealer for buying these items.

REMOTE CONTROL BUTTONS

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 9/75

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 10/75

DISPLAY CELL DEFECT SPECIFICATION

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 11/75

DEFINITION OF CELL DEFECT ZONE

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE

BSV-4251/4251A RD(1) 00 03/10/23 12/75

2) Display Dot Diagram

MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE