Simens Elektra Saob. Sig

Download as pdf or txt
Download as pdf or txt
You are on page 1of 197

s

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Elektra Installation, Commissioning and Maintenance Manual

Document No. 667/HB/33930/000


THIS DOCUMENT IS ELECTRONICALLY APPROVED AND HELD IN THE SIEMENS DOCUMENT CONTROL TOOL Prepared By Siemens Mobility, Traffic Solutions Engineering S. White/L. Crawley/A. White/K. Napper Engineer/Lecturer/Eng Mngr/Lead Eng Checked and Released Siemens Mobility, Traffic Solutions Engineering D. Martin Engineering Manager

Company/Dept. Department Name Function Signature Date 20 January 2011 20 January 2011 COPYRIGHT STATEMENT The information contained herein is the property of Siemens plc. and is supplied without liability for errors or omissions. No part may be reproduced or used except as authorised by contract or other written permission. The copyright and the foregoing restriction on reproduction and use extend to all media in which the information may be embodied. Siemens plc 2010, All Rights Reserved

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

1 of 197 Released 20 January 2011 667/HB/33930/000

s
SAFETY WARNINGS

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

In the interests of health and safety, when using or servicing this equipment, the following instructions must be noted and adhered to: (i) Only Skilled or Instructed personnel with relevant technical knowledge and experience, who are also familiar with the safety procedures required when dealing with modern electrical or electronic equipment, are to be allowed to use and/or work on the equipment. All work shall be performed in accordance with the Electricity at work Regulations 1989 and the relevant Highways Agency (DoT) procedures of test and maintenance. (ii) Such personnel must take heed of all relevant notes, cautions and warnings in this handbook, and any other documents and handbook associated with the equipment including, but not restricted to, the following: (a) The equipment must be correctly connected to the specified incoming power supply. (b) The equipment must be disconnected/isolated from the incoming power supply before removing protective covers or working on any part from which protective covers have been removed. Batteries This equipment contains a Lithium battery and a Lead Acid Battery. Do not short circuit, recharge, puncture, take apart, incinerate, crush, immerse, force discharge or expose to temperatures above the declared operating temperature range of the product, otherwise there is a risk of fire or explosion. Batteries should be handled and stored carefully to avoid short circuits. Do not store in disorderly fashion, or allow metal objects to be mixed with stored batteries. Keep batteries between -30C and 35C for prolonged storage. The batteries are sealed units which are not hazardous when used according to these recommendations. Do not breathe vapours or touch any internal material with bare hands. Battery disposal method should be in accordance with local, state and government regulations. In many countries, batteries should not be disposed of into ordinary household waste. They must be recycled properly to protect the environment and to cut down on the waste of precious resources.

IMPORTANT

There are several RJ45 connectors used within the sign. With the exception of the connector at the rear of the Gemini, they are not Ethernet ports and should not be connected to other equipment, including PCs.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

2 of 197 Released 20 January 2011 667/HB/33930/000

s
Contents
1 1.1 1.2 1.3 1.4 2 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 4 4.1 4.2 5 5.1 5.1.1 5.1.2 5.1.3 5.1.4 5.1.4.1 5.1.4.2 5.2 5.2.1 5.2.2 5.2.2.1 5.2.2.2 5.2.2.3 5.2.2.4 5.2.2.5 5.2.2.6 5.2.2.7 5.2.2.8 5.2.2.9 5.2.2.10 5.2.2.11 5.2.2.12 5.2.2.13 5.2.2.14 5.2.2.15 5.2.2.16 5.2.2.17 5.2.2.18 5.2.2.19 5.2.2.20 5.2.2.21 5.2.2.22 5.2.2.23 5.2.2.24 5.2.3 5.2.3.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Introduction............................................................................................................................... 12 Purpose .................................................................................................................................... 12 Scope ....................................................................................................................................... 12 Abreviations.............................................................................................................................. 12 References ............................................................................................................................... 14 Product general description ..................................................................................................... 15 CE and performance ................................................................................................................ 18 BS EN 12966-1 ........................................................................................................................ 18 Summary of key performance characteristics.......................................................................... 18 EMC Performance.................................................................................................................... 18 RoHS Compliance.................................................................................................................... 18 WEEE Directive........................................................................................................................ 18 LED and Laser Classification ................................................................................................... 19 Quality and Reliability............................................................................................................... 19 Supported Character Set ......................................................................................................... 19 Safety requirementS ................................................................................................................ 20 Safety of Maintenance Personnel ............................................................................................ 20 Elektra Working at Height Provisions....................................................................................... 22 ELEKTRA equipment ............................................................................................................... 23 Elektra enclosure exterior ........................................................................................................ 23 Mounting options...................................................................................................................... 24 Mains Connection Options ....................................................................................................... 24 Power Supply Options and Requirements ............................................................................... 25 Power Consumption................................................................................................................. 26 Example Power Calculation Traffic Information Sign............................................................ 27 Example Power Calculation Car Park Sign........................................................................... 28 the Elektra enclosure interior ................................................................................................... 30 Simplified Sign block diagram .................................................................................................. 31 Internal sign modules ............................................................................................................... 32 Master Switch Assembly - 667/2/44650/000 standard / 667/2/44650/001 fully populated .... 32 500VA Transformer Assembly 667/1/44670/000 .................................................................. 35 Switched Mode Power Supply Assembly 667/1/44675/000 ................................................. 36 The Comms Panel 667/1/44630/000 (Includes Gemini)....................................................... 37 The Antenna............................................................................................................................. 38 The Row driver Module Assembly 667/1/33980/002 ............................................................ 40 The Row Driver 7-Segment Display......................................................................................... 41 Sensor module 667/1/33980/001 .......................................................................................... 43 The Display modules................................................................................................................ 44 100mm Character PCB Assembly (Yellow) 667/1/33951/001 .............................................. 45 100mm Character PCB Assembly (Red/Green) - 667/1/33951/002........................................ 46 160mm Character PCB Assembly (Yellow Full Matrix) 667/1/33953/001 ............................ 47 160mm Character PCB Assembly(Red/Green) Full Matrix - 667/1/33953/002 ....................... 48 160mm Character PCB Assembly (Yellow) 5 x 7 Matrix - 667/1/33957/001 ........................... 48 Colour selection on Red and Green Display modules ............................................................. 49 240mm Character PCB Assembly (Yellow) 667/1/33955/001 .............................................. 49 320mm Display (Yellow) 2 x 667/1/33953/001 ..................................................................... 50 Graphical Arrows...................................................................................................................... 50 The VLED PSU 667/1/33966/001 ......................................................................................... 52 Lantern Display Assembly 667/1/44610/800 ........................................................................ 52 Lantern Cabling arrangement .................................................................................................. 53 Display Blanking....................................................................................................................... 55 The Heater ............................................................................................................................... 55 Door Switches .......................................................................................................................... 57 The Elektra Gemini - 667/1/32605/102 .................................................................................... 58 Functionality ............................................................................................................................. 58
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 3 of 197 Released 20 January 2011 667/HB/33930/000

Security classification Version Last Editor Document Name

s
5.2.3.2 5.2.3.3 5.2.3.4 5.2.3.5 5.2.3.6 5.2.3.7 5.2.3.8 5.2.4 5.2.4.1 5.2.4.2 5.2.4.3 5.2.4.4 5.2.4.5 5.2.4.6 6 7 7.1 7.2 7.3 7.4 7.5 7.6 8 8.1 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.3 8.3.1 8.3.2 8.3.3 8.3.4 8.4 8.4.1 8.4.2 8.4.3 8.5 8.5.1 8.5.1.1 8.5.1.2 9 9.1 10 10.1 10.2 10.3 10.3.1.1 10.4 10.4.1.1 10.4.1.2 10.4.1.3 10.5 11 11.1 11.2 11.3

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Gemini Mains Supply ............................................................................................................... 60 Support Batteries ..................................................................................................................... 60 The Processor Card ................................................................................................................. 60 Isolated Outputs ....................................................................................................................... 62 Digital Inputs............................................................................................................................. 62 Additional IO Board for Parallel UTC Interface ........................................................................ 62 The RS232/RS422 Converter .................................................................................................. 63 Direct/Local Connection and Security...................................................................................... 64 The RS232 Communications Link............................................................................................ 65 Bluetooth Communication Link ................................................................................................ 65 Instation Remote Connection................................................................................................... 65 Remote Access to Web Pages ................................................................................................ 66 The Modem Power Supply....................................................................................................... 66 The MC35 GPRS Modem ........................................................................................................ 67 Elektra Connectivity ................................................................................................................. 68 Elektra site pre-operation process ........................................................................................... 71 Foundations and pole infrastructure ........................................................................................ 72 Installation first fix.................................................................................................................. 72 Electricity connection ............................................................................................................... 72 Installation second fix............................................................................................................ 72 Commissioning......................................................................................................................... 72 Customer Site Acceptance Testing.......................................................................................... 72 Installation ................................................................................................................................ 73 General Torque Settings .......................................................................................................... 73 Monopole sign .......................................................................................................................... 73 Installation of foundation and Anchor Frame ........................................................................... 73 Cantilever erection ................................................................................................................... 73 Fitting the sign to the cantilever ............................................................................................... 75 Connection of mains cable....................................................................................................... 76 simple monopole ...................................................................................................................... 77 Installation of foundation and Anchor Frame ........................................................................... 77 Stanchion erection ................................................................................................................... 77 Fitting the sign to the stanchion ............................................................................................... 77 Connection of mains cable....................................................................................................... 77 Multipole ................................................................................................................................... 78 Installation of Poles .................................................................................................................. 78 Installation of Sign .................................................................................................................... 78 Connection of mains cable....................................................................................................... 81 electricity connection................................................................................................................ 82 Fitting and Termination of Mains Cable ................................................................................... 83 Mains Cable Supplied With Sign.............................................................................................. 83 Mains Cable Not Supplied With Sign ....................................................................................... 84 Installation second fix............................................................................................................ 87 Visual inspection ...................................................................................................................... 87 Testing...................................................................................................................................... 88 Insulation test ........................................................................................................................... 88 Polarity test............................................................................................................................... 89 Earth loop impedance test ....................................................................................................... 90 Earth tests within the Elektra enclosure................................................................................... 91 Maintenance socket RCD test.................................................................................................. 92 No-trip test................................................................................................................................ 92 Rated trip current test............................................................................................................... 92 Fast trip current test ................................................................................................................. 92 Completion of installation checklist .......................................................................................... 92 Commissioning......................................................................................................................... 93 Turn the Sign On ...................................................................................................................... 93 Power up check........................................................................................................................ 93 Diagnostic WEB interface connect........................................................................................... 93
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 4 of 197 Released 20 January 2011 667/HB/33930/000

Security classification Version Last Editor Document Name

s
11.4 11.5 11.6 11.7 11.8 11.9 11.10 11.11 11.12 11.12.1 11.12.2 11.12.2.1 11.12.2.2 11.12.2.3 11.12.2.4 11.12.2.5 11.13 12 12.1 12.2 12.3 12.4 12.5 12.5.1 12.5.1.1 12.5.1.2 12.5.1.3 12.5.1.4 12.5.2 12.5.2.1 12.5.2.2 12.5.2.3 12.5.2.4 12.5.2.5 12.5.2.6 12.5.3 12.5.4 12.5.4.1 12.5.4.2 12.5.4.3 12.5.4.4 12.5.4.5 12.5.4.6 12.5.4.7 12.5.4.8 12.5.4.9 12.5.4.10 12.5.4.11 12.5.4.12 13 13.1 13.1.1 13.1.2 13.1.3 13.1.3.1 13.1.3.2 13.2 13.3

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Checking Sign Configuration.................................................................................................... 94 Setting the luminance parameters ........................................................................................... 96 Colour Selection for Red / Green Display modules ................................................................. 97 Heater test................................................................................................................................ 99 Light sensor test..................................................................................................................... 100 Display test............................................................................................................................. 100 Checking the Status of the MC35 GPRS Modem .................................................................. 102 Measuring Signal Strength at MC35 Modem ......................................................................... 103 Configuring Sign for External Control .................................................................................... 104 Graphical Arrows.................................................................................................................... 104 Elektra Control Modes............................................................................................................ 104 Configuration of UTMC Application...................................................................................... 104 Configuration of UVMS Application...................................................................................... 104 Configuration of IO Application ............................................................................................ 104 Configuration of Tester Application ...................................................................................... 104 Starting Applications............................................................................................................. 105 SETTING A LEGEND FROM THE INSTATIoN. .................................................................... 105 Maintenance........................................................................................................................... 107 Routine maintenance ............................................................................................................. 107 Cleaning ................................................................................................................................. 107 Yearly intervals....................................................................................................................... 107 Three yearly intervals............................................................................................................. 108 Diagnostics and fault finding .................................................................................................. 108 Fault Diagnosis....................................................................................................................... 108 Gemini fault monitoring .......................................................................................................... 109 Display Board Pixel faults ...................................................................................................... 109 Sign Configuration Faults....................................................................................................... 112 Communications Failures....................................................................................................... 114 Elektra fault Codes................................................................................................................. 116 Generic IO Application ........................................................................................................... 116 UVMS Over IP Application ..................................................................................................... 116 UTMC Application .................................................................................................................. 116 Environment Library ............................................................................................................... 117 UVMS Library ......................................................................................................................... 117 GSPI Library........................................................................................................................... 119 Visual Fault Indicators............................................................................................................ 121 Module replacement............................................................................................................... 123 Replacement: Light sensor .................................................................................................... 123 Replacement: Modem Antenna.............................................................................................. 123 Replacement: Sensor Module................................................................................................ 124 Replacement: Row Driver Module ......................................................................................... 125 Replacement: VLED PSU ...................................................................................................... 125 Replacement: Display module ............................................................................................... 126 Replacement: Lantern module ............................................................................................... 127 Replacement: Gemini............................................................................................................. 127 Replacement: Modem ............................................................................................................ 128 Removal: Comms module.................................................................................................... 128 Replacement; Transformer .................................................................................................. 129 Replacement; SMPS ............................................................................................................ 130 Elektra Specific Status and configuration Web pages ........................................................... 131 Sign Setup.............................................................................................................................. 131 Status ..................................................................................................................................... 131 Hardware Configuration ......................................................................................................... 134 Configuration of Graphical Arrows and 320mm Operation .................................................... 134 Graphical arrows .................................................................................................................... 134 320mm operation ................................................................................................................... 135 Peripheral Firmware Update .................................................................................................. 137 System ................................................................................................................................... 138
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 5 of 197 Released 20 January 2011 667/HB/33930/000

Security classification Version Last Editor Document Name

s
13.4 13.5 13.5.1 13.5.2 13.5.3 13.5.4 13.5.5 13.5.6 13.5.7 13.5.8 13.5.9 13.5.10 13.5.11 13.5.12 13.5.13 13.5.14 13.5.15 13.5.16 13.5.17 13.5.18 13.5.19 13.5.20 13.6 13.6.1 13.6.2 13.6.3 13.6.4 13.7 13.7.1 13.7.2 13.7.2.1 13.7.2.2 13.7.3 13.8 13.8.1 13.8.2 13.8.3 13.8.4 13.8.4.1 13.9 13.9.1 13.9.2 13.9.3 13.9.4 13.9.5 13.9.6 13.9.7 13.9.8 13.10 13.10.1 13.10.2 13.10.3 13.10.4 13.10.4.1 13.10.4.2 13.10.5 13.10.6 13.10.6.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Tester ..................................................................................................................................... 139 StatusConfig Common Web Interface Screens ..................................................................... 141 SITE LOG SCREEN............................................................................................................... 141 SYSTEM LOG SCREEN........................................................................................................ 141 GPRS Screen......................................................................................................................... 141 Basic Status Screen............................................................................................................... 143 Ethernet Screen ..................................................................................................................... 143 DNS Screen ........................................................................................................................... 144 DDNS Screen......................................................................................................................... 144 OSS Screen ........................................................................................................................... 145 PPP Screen............................................................................................................................ 146 TFTP Screen .......................................................................................................................... 148 SNMP Screen......................................................................................................................... 149 Services Screen ..................................................................................................................... 150 Telnet Server Screen ............................................................................................................. 150 SysCtl Screen......................................................................................................................... 151 Firewall Screen....................................................................................................................... 151 Light Weight Tunnel Screen................................................................................................... 152 HTTP Screen.......................................................................................................................... 153 Terminal Screen ..................................................................................................................... 154 Digital IO Screen .................................................................................................................... 154 TCL Screen ............................................................................................................................ 155 StatusConfig: Environment Monitor ....................................................................................... 155 General Screen ...................................................................................................................... 155 Status Screen......................................................................................................................... 156 Door........................................................................................................................................ 156 Heater Screen ........................................................................................................................ 157 StatusConfig: GSPI ................................................................................................................ 159 General................................................................................................................................... 159 Status ..................................................................................................................................... 159 Luminance Screen ................................................................................................................. 159 Communications Screen ........................................................................................................ 160 Upload/Download Screen ...................................................................................................... 161 StatusConfig: Generic IO Application .................................................................................... 161 General................................................................................................................................... 161 Status ..................................................................................................................................... 162 IO............................................................................................................................................ 163 Message Rules Screen .......................................................................................................... 164 Rule Screen Rule n ............................................................................................................. 164 StatusConfig: Production Tests.............................................................................................. 165 General................................................................................................................................... 165 Log Sensor Readings............................................................................................................. 165 Lantern Brightness ................................................................................................................. 166 Lantern Sequence.................................................................................................................. 166 Display Checkerboard............................................................................................................ 167 Display Preset Message ........................................................................................................ 167 Luminance Band .................................................................................................................... 168 Luminance Override............................................................................................................... 168 StatusConfig: UTMC Application............................................................................................ 169 General................................................................................................................................... 169 Instation Compatibility ............................................................................................................ 169 MIB Config.............................................................................................................................. 170 Sign Setup.............................................................................................................................. 170 Display.................................................................................................................................. 171 Lantern ................................................................................................................................. 172 Comms Check........................................................................................................................ 172 Luminance Override............................................................................................................... 173 Display.................................................................................................................................. 173
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 6 of 197 Released 20 January 2011 667/HB/33930/000

Security classification Version Last Editor Document Name

s
13.10.6.2 13.11 13.11.1 13.11.2 13.11.3 13.11.4 13.11.4.1 13.11.5 13.11.6 13.11.7 13.11.8 13.12 13.12.1 13.12.2 13.12.3 14 14.1 14.2 14.3 14.3.1 14.3.1.1 14.3.1.2 14.3.2 14.4 14.5 14.6 14.7

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Lantern ................................................................................................................................. 173 StatusConfig: UVMS Library .................................................................................................. 174 General................................................................................................................................... 174 Pixel Monitoring...................................................................................................................... 175 Lantern Position ..................................................................................................................... 176 PWM Modifiers ....................................................................................................................... 177 Luminance Band Modifier - Band n...................................................................................... 177 Luminance Bands .................................................................................................................. 178 Graphical Arrows.................................................................................................................... 179 Special Words ........................................................................................................................ 179 Preset Messages ................................................................................................................... 180 StatusConfig: UVMS Over IP Application .............................................................................. 180 General................................................................................................................................... 180 Instation IP Communications ................................................................................................. 181 Luminance Overrides ............................................................................................................. 182 Appendices............................................................................................................................. 183 Appendix A - Installation Checklist......................................................................................... 183 APPENDIX A - Commissioning Checklist .............................................................................. 184 Appendix B Updating Firmware .......................................................................................... 185 Updating Gemini Firmware .................................................................................................... 185 Upgrade Gemini Already Running Elektra Firmware ............................................................. 185 Converting Non-Elektra Gemini for use in Elektra ................................................................. 185 Programming Peripheral Boards (Sensor & Row Drivers)..................................................... 186 Appendix C Importing / Exporting Configurations ............................................................... 187 Appendix D Part Numbers and Spares List ........................................................................ 188 Appendix E GNU General Public Licence........................................................................... 191 Appendix F Certificate of Conformity ................................................................................... 195

TABLE OF FIGURES Figure 1 Typical Elektra Signs................................................................................................................ 15 Figure 2 Typical Elektra Display Configurations..................................................................................... 16 Figure 3 - System Communications Overview .......................................................................................... 17 Figure 4 - Ladder Strap Tie-Off ................................................................................................................. 22 Figure 5 - Ladder Tie-Off to frame............................................................................................................. 22 Figure 6 - Work Positioning Bar................................................................................................................. 22 Figure 7 - Typical Traffic Information Sign Exterior View .......................................................................... 23 Figure 8 - Typical Car Park Guidance Sign Exterior View......................................................................... 23 Figure 9 Typical Power Consumption of Sign Modules.......................................................................... 26 Figure 10 - Elektra Block Diagram............................................................................................................. 30 Figure 11 - Sign Block Diagram (Showing only one row and no lanterns)................................................ 31 Figure 12 - The Master Switch Assembly.................................................................................................. 32 Figure 13 - Master Switch Assembly Identification Standard (667/1/44650/000) .................................. 33 Figure 14 - Master Switch Assembly Identification Fully populated (667/1/44650/001.......................... 33 Figure 15 - Master Switch Assembly Circuit Diagram ............................................................................... 34 Figure 16 - Master Switch Assembly Part Numbers.................................................................................. 34 Figure 17-Master Switch Assembly with Cover Removed ........................................................................ 35 Figure 18 - Power Supply Transformer Figure 19 - Transformer Circuit Diagram............................ 35 Figure 20 - Transformer mounting plate with lifting hole ........................................................................... 36 Figure 21 - Switch Mode Power Supply .................................................................................................... 36 Figure 22 - PSU mounting plate with lifting hole ....................................................................................... 36 Figure 23 - Comms Panel.......................................................................................................................... 37 Figure 24 - Comms Panel adjustment ....................................................................................................... 38 Figure 25 - The Antenna............................................................................................................................ 38 Figure 26 - The Light Sensor..................................................................................................................... 38 Figure 27 - Row Driver Module (Front)...................................................................................................... 40 Figure 28 - Row Driver LED States ........................................................................................................... 41 Figure 29 7- Segment blank ................................................................................................................... 41
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 7 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 30 7- Segment dashes ................................................................................................................ 41 Figure 31 7- Segment Address Digits..................................................................................................... 41 Figure 32 Hexadecimal Address ............................................................................................................ 42 Figure 33 - Row Driver Module (Rear) ...................................................................................................... 42 Figure 34 - The Sensor Module................................................................................................................. 43 Figure 35 - Sensor Module LED States..................................................................................................... 44 Figure 36 - 100mm Character PCB Assembly (Yellow) - Viewed from front............................................. 45 Figure 37 - 100mm Character PCB Assembly (Yellow) Viewed from rear............................................. 45 Figure 38 - 100mm Character PCB Assembly (Yellow) with VLED PSU fitted ......................................... 46 Figure 39 - 100mm Character PCB Assembly (Red/Green) - Viewed from Front ................................... 46 Figure 40 - 100mm Character PCB Assembly (Red/Green) Viewed from Rear .................................... 47 Figure 41 - 100mm Character PCB Assembly (Red/Green) with VLED PSUs and Row Driver fitted. ..... 47 Figure 42 - 160mm Character PCB Assembly (Yellow Full Matrix) Viewed from Rear ......................... 48 Figure 43 - 160mm Character PCB Assembly (Red/Green) Full Matrix Viewed from Rear .................. 48 Figure 44 160mm Character PCB Assembly (Yellow) 5 x 7 Matrix........................................................ 49 Figure 45 - 240mm Character PCB Assembly (Yellow) Viewed from Rear .......................................... 50 Figure 46 - Graphical arrow comprised of 2 x 100mm Character PCB Assemblies ................................. 51 Figure 47 - Graphical Arrow Arrangement - Viewed from Rear ................................................................ 51 Figure 48 VLED Power Supply Board ................................................................................................... 52 Figure 49 - Lantern Module (first) .............................................................................................................. 53 Figure 50 - Lantern PCB............................................................................................................................ 53 Figure 51 - Lantern Cabling arrangement ................................................................................................. 54 Figure 52 - Lantern Block Diagram............................................................................................................ 54 Figure 53 Heater arrangement ............................................................................................................... 55 Figure 54 Gemini I/O connections .......................................................................................................... 56 Figure 55 Heater flow chart (Simplified) ............................................................................................... 56 Figure 56 Temperature thresholds ......................................................................................................... 57 Figure 57 Humidity thresholds................................................................................................................ 57 Figure 58 Door Switch Locations............................................................................................................ 57 Figure 59 Door Switch Connections to Gemini ...................................................................................... 58 Figure 60 Door Switch Connection details ............................................................................................. 58 Figure 61 - Door Switch diagram............................................................................................................... 58 Figure 62 - ELEKTRA Gemini 2 with the RS232/RS422 board fitted........................................................ 59 Figure 63 Identifying the correct Gemini Unit ......................................................................................... 59 Figure 64 Gemini Interfaces .................................................................................................................. 59 Figure 65 Gemini Mains Connections .................................................................................................... 60 Figure 66 Gemini Battery Details............................................................................................................ 60 Figure 67 Gemini LED Indicators ........................................................................................................... 61 Figure 68 Gemini LED interpretation ...................................................................................................... 61 Figure 69 Gemini Output Specifications ................................................................................................. 62 Figure 70 Gemini Input Specifications.................................................................................................... 62 Figure 71 - WEZ I/O Board ........................................................................................................................ 63 Figure 72 - Digital input pins...................................................................................................................... 63 Figure 73 RS 232/422 Converter............................................................................................................ 64 Figure 74 RS 232/422 Comms Module LEDs ........................................................................................ 64 Figure 75 Bluetooth Link......................................................................................................................... 65 Figure 76 Ports for Instation Communication ......................................................................................... 65 Figure 77 - Modem Power Supply Connections C .................................................................................... 66 Figure 78 MC35 GPRS Modem.............................................................................................................. 67 Figure 79 MC35 GPRS Modem LED Indications ................................................................................... 67 Figure 80 - Elektra internal connectivity 240mm .................................................................................... 68 Figure 81 - Elektra internal connectivity 100mm / 160mm Yellow ......................................................... 69 Figure 82 - Elektra internal connectivity 100mm / 160mm R&G ............................................................... 70 Figure 83 Pre-operation chart................................................................................................................. 71 Figure 84 Threading the Draw Rope through the cantilever .................................................................. 74 Figure 85 - Erecting the Cantilever............................................................................................................ 74 Figure 86 - Checking the Cantilever is Vertical ......................................................................................... 74 Figure 87 - Fitting the Sign Enclosure to the Cantilever............................................................................ 75
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 8 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 88 - Cantilever Sign Elevation Adjustment..................................................................................... 76 Figure 89 - Location of U-Bolt Brackets (View from front of sign) ............................................................. 78 Figure 94 - Multipole enclosure fitted to the Poles .................................................................................... 81 Figure 95 - Mains Connection Scheme ..................................................................................................... 82 Figure 97 - Mains Cable Gland Plate ........................................................................................................ 85 Figure 98 - Mains Cable Connection ......................................................................................................... 85 Figure 99 MOVs (Metal Oxide Varistors)................................................................................................ 88 Figure 100 - Gemini LEDs on Start Up...................................................................................................... 93 Figure 101 Web Browser User Name and Password............................................................................. 94 Figure 102 - Outstation initial login ............................................................................................................ 94 Figure 103 - Sign Configuration................................................................................................................. 95 Figure 104 - Luminance Band Settings ..................................................................................................... 96 Figure 105 PWM Modifiers ..................................................................................................................... 96 Figure 106 - Luminance Band Modifier entry ............................................................................................ 97 Figure 107 - Enable Special Words Compare ........................................................................................... 98 Figure 108 - Specify Special Words .......................................................................................................... 98 Figure 109 - Heater Information ................................................................................................................ 99 Figure 110 - Sensor Status...................................................................................................................... 100 Figure 111 -System Page with Tester Running....................................................................................... 101 Figure 112 - Tester page ......................................................................................................................... 101 Figure 113 - Checking the Fault Table after running tests ...................................................................... 102 Figure 114 - MC35 LED Indications ........................................................................................................ 102 Figure 115 - MC35 Signal Strength Measurement Equipment................................................................ 103 Figure 116 - Running the Generic I/O application ................................................................................... 105 Figure 117 - Setting the Sign from the..................................................................................................... 106 Figure 118 - Fault Table showing Pixel Faults ........................................................................................ 109 Figure 119 - Locating a Display Board Fault ........................................................................................... 110 Figure 120 - System Log Showing Pixel Faults....................................................................................... 110 Figure 121 - Locating a Yellow Pixel Fault .............................................................................................. 111 Figure 122 - Red Pixel Fault.................................................................................................................... 111 Figure 123 - Green Pixel Fault ................................................................................................................ 112 Figure 124 Locating a Red/Green Pixel Fault ...................................................................................... 112 Figure 125 - Actual Sign does not match Config..................................................................................... 113 Figure 126 - Light Sensor Fault ............................................................................................................... 113 Figure 127 - Light Sensor Fault System Log information ........................................................................ 114 Figure 128 - Communications Failure ..................................................................................................... 115 Figure 129 Visual Fault Indicators ........................................................................................................ 122 Figure 130 - Replacing the Light Sensor ................................................................................................. 123 Figure 131 - Replacing the Modem Antenna........................................................................................... 123 Figure 132 - Replacing the Sensor Module ............................................................................................. 124 Figure 133 - Replacing the Row Driver Module ...................................................................................... 125 Figure 134 - Replacing VLED PSU ......................................................................................................... 125 Figure 135 - Replacing Display Modules................................................................................................. 126 Figure 136 - Replacing the Lanterns ....................................................................................................... 127 Figure 137 - Replacing the Gemini.......................................................................................................... 128 Figure 138 - Replacing the Comms Module ............................................................................................ 129 Figure 139 - Replacing Transformers...................................................................................................... 130 Figure 140 - Replacing SMPS ................................................................................................................. 130 Figure 141 - Sign Configuration (Running).............................................................................................. 131 Figure 142 - Sign Configuration (Sign doesn't match config).................................................................. 132 Figure 143 - Sign Configuration (Attempting to access GSPI) ................................................................ 132 Figure 144 - Arrow Selection ................................................................................................................... 135 Figure 145 - Configuration of Double Height / Width Operation.............................................................. 136 Figure 146 - Verification of Double Height / Width Operation ................................................................. 136 Figure 147 - Peripheral Firmware Update ............................................................................................... 137 Figure 148 - Peripheral Firmware Update, No Peripherals Detected...................................................... 137 Figure 149 - System (Part 1) ................................................................................................................... 138 Figure 150 - System (Part 2) ................................................................................................................... 139
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 9 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 151 - Tester .................................................................................................................................. 140 Figure 152 - GPRS .................................................................................................................................. 141 Figure 153 - Basic Status ........................................................................................................................ 143 Figure 154 - Ethernet............................................................................................................................... 143 Figure 155 - DNS..................................................................................................................................... 144 Figure 156 - DDNS .................................................................................................................................. 144 Figure 157 - OSS Interface...................................................................................................................... 145 Figure 158 -PPP ...................................................................................................................................... 146 Figure 159 - TFTP ................................................................................................................................... 148 Figure 160 - SNMP .................................................................................................................................. 149 Figure 161 - Services............................................................................................................................... 150 Figure 162 - Telnet Server....................................................................................................................... 150 Figure 163 - SysCtl .................................................................................................................................. 151 Figure 164 - Firewall ................................................................................................................................ 151 Figure 165 - LwTunnel............................................................................................................................. 152 Figure 166 - HTTP ................................................................................................................................... 153 Figure 167 - Terminal .............................................................................................................................. 154 Figure 168 - Digital I/O............................................................................................................................. 154 Figure 169 - TCL...................................................................................................................................... 155 Figure 170 - Temperature - General........................................................................................................ 155 Figure 171 - Sensor Status Information................................................................................................... 156 Figure 172 - Door Input Information ........................................................................................................ 156 Figure 173 - Heater Information .............................................................................................................. 157 Figure 174 - General................................................................................................................................ 159 Figure 175 - Display of PWM Signals...................................................................................................... 159 Figure 176 - Communications ................................................................................................................. 160 Figure 177 - Upload/Download................................................................................................................ 161 Figure 178 - Generic IO Application, General ......................................................................................... 161 Figure 179 - Generic IO Application, Status ............................................................................................ 162 Figure 180 - Generic IO Application, IO .................................................................................................. 163 Figure 181 - Message Rules ................................................................................................................... 164 Figure 182 - Rule 0 .................................................................................................................................. 164 Figure 183 - Production Tests, General .................................................................................................. 165 Figure 184 - Production Tests, Log Sensor Readings ............................................................................ 165 Figure 185 - Production Tests, Lantern Brightness................................................................................. 166 Figure 186 - Production Tests, Lantern Sequence.................................................................................. 166 Figure 187 - Production Tests, Display Checkerboard............................................................................ 167 Figure 188 - Production Tests, Display Preset Message ........................................................................ 167 Figure 189 - Production Tests, Luminance Band .................................................................................... 168 Figure 190 - Production Tests, Luminance Override............................................................................... 168 Figure 191 - General................................................................................................................................ 169 Figure 192 - Instation Compatibility ......................................................................................................... 169 Figure 193 - MIB Configuration ............................................................................................................... 170 Figure 194 - Sign Setup........................................................................................................................... 170 Figure 195 - Display Configuration .......................................................................................................... 171 Figure 196 - Lantern Configuration.......................................................................................................... 172 Figure 197 - Comms Check..................................................................................................................... 172 Figure 198 - Display Override PWM Levels ............................................................................................ 173 Figure 199 - Lantern Override PWM Levels ............................................................................................ 173 Figure 200 - UVMS Library - General...................................................................................................... 174 Figure 201 - Pixel Monitoring................................................................................................................... 175 Figure 202 - Lantern Positions ................................................................................................................ 176 Figure 203 - Luminance Modifiers - Band n ............................................................................................ 177 Figure 204 - Luminance Bands ............................................................................................................... 178 Figure 205 - Graphical Arrows................................................................................................................. 179 Figure 206 - Special Words ..................................................................................................................... 179 Figure 207 - Preset Messages ................................................................................................................ 180 Figure 208 - General................................................................................................................................ 180
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 10 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 209 - Instation IP Communications .............................................................................................. 181 Figure 210 - Luminance Overrides .......................................................................................................... 182 Figure 211 - First Fix Checklist................................................................................................................ 183 Figure 212 - Second Fix Checklist........................................................................................................... 183 Figure 213 - Commissioning Checklist .................................................................................................... 184 INDEX OF TABLES Table 1 - Change History........................................................................................................................... 11 Table 2- Insulation Test Switch State ........................................................................................................ 88 Table 3 - Polarity Test Switch State .......................................................................................................... 89 Table 4 - Polarity Test Limits ..................................................................................................................... 90 Table 4 - Earth Loop Impedance Test Switch State.................................................................................. 91 Table 6 - Earth Loop Impedance Enclosure locations and values ............................................................ 91 Table 7 - Typical Lux Values .................................................................................................................. 100 Table 8 - Sign Statuses ........................................................................................................................... 133 Table 9 - Sign Configuration - available buttons ..................................................................................... 134 Table 10- File System Upgrade Process................................................................................................. 186

Change History
Version a b c d Date 14 January 2010 29 June 2010 16 August 2010 28 August 2010 Change First draft Update Update Update Update Update First Issue Author S. White L.Crawley L.Crawley L.Crawley/A. White/K. Napper A. White A. White A. White

e 23 December 2010 f 20 January 2011 1 20 January 2011 Table 1 - Change History

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

11 of 197 Released 20 January 2011 667/HB/33930/000

s
1
1.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

INTRODUCTION
PURPOSE

This document is intended to provide sufficient information to the user to Install, Commission and Maintain Elektra Car Park Guidance and Message Signs.

1.2

SCOPE

This document covers the Installation, Commissioning and Maintenance of the Elektra Signs, and should be used in conjunction with the GVP Reference Manual (667/HB/31760/000). If an Outstation Support Server is being used, the Outstation Support Server Handbook (667/HB/31760/100) should be consulted. The GVP Reference Manual is intended as a reference manual for the Gemini 2 Generic Versatile Platform (GVP) web interface and handset commands. The manual describes the web screens and handset commands provided by the basic GVP, with each application running on GVP having additional web screens and handset commands, which are described in individual product handbooks. The Outstation Support Server (OSS) Handbook covers the installation and use of the OSS including details of software package management and configuration backup facilities for Siemens networked outstations. The OSS software covered in the handbook is identified as part number 667/TZ/32450/000.

1.3

ABREVIATIONS

Document Specific Abbreviations and Definitions Abbreviation Explanation ASCII CPC CPU DNO DSL ELV American Standard Code for Information Interchange a character encoding, based on the English alphabet. Circuit Protective conductor Central Processing Unit (computer) Distributed Network Operator DSL (Digital Subscriber Line) is a set of standards (e.g. ADSL, VDSL) for broadband network connectivity over public telephone lines. Extra Low Voltage a voltage defined by IEC 61201 and PD 6536 as being one which does not have a potential above ground of greater than 50V rms AC or 120V DC Earth Loop Impedance Electromagnetic Compatibility Non-volatile read/write memory, programmable in blocks. Fast and cheap mass storage for applications that require non-volatility. General Packet Radio Service It is an always on wireless technology used by GSM (Global System for Mobile) networks which enables Internet and other data communication. Global System for Mobile (originally Groupe Speciale Mobile) A mobile phone standard capable of both voice and moderate speed data traffic and SMS text messaging. Also referred to as 2G, 2.5G, or 2.75G according to the capabilities of the phone being attached to the system. Gradually being replaced by the UMTS (3rd Generation or 3G) standard that is capable of far greater data speeds. Gemini Serial Peripheral Interface
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 12 of 197 Released 20 January 2011 667/HB/33930/000

ELI EMC FLASH GPRS

GSM

GSPI
Security classification Version Last Editor Document Name

s
GVP HMDD IP In-Station LED MCB MDU MEWP MIB MOV OS OSS Hardware Module Design Document

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Generic Versatile Platform a software platform on Gemini hardware. Internet Protocol a protocol for communication across packet-switched networks using TCP/IP suite of protocols Term used for the control centre where the control system that manages one or more UVMS signs is situated. Light-Emitting Diode Miniature Circuit Breaker an overload protection device Mains Distribution Unit Mobile Elevating Work Platform Management Information Base Metal Oxide Varistor Operating System Outstation Support Server a software application at the in-station that enables access to a range of features supported by the out-station Gemini controller. (e.g. firmware upload and download) These Siemens-specific features are not supported by the UTMC or Siespace (UVMS) applications at the in-station and therefore need to be provided separately via the OSS. Re-named from GSS to OSS to decouple it from Gemini. Printed Circuit Board Protected Extra-Low Voltage Circuit a circuit having a connection to earth and in which the voltage cannot exceed ELV under normal and single-fault conditions Public Switched Telephone Network Power Supply Unit Pulse-Width Modulation Random Access Memory Residual Current Device Regional Electricity Company System Design Specification Square Hollow Section The software that runs on an in-station PC to control signs. Signs that run either the Siespace(UVMS) protocol or the UTMC protocol are controlled by the Siespace in-station. Other documents may use the term Siespace to denote either the in-station or the protocol. This document uses Siespace to denote the in-station . Siespace is now being superceded by Comet VMS Plug in. The Siespace protocol UVMS protocol. Throughout this document, Siespace(UVMS) is used to denote the protocol Software Module Design Document Switched Mode Power Supply Unit Simple Network Management Protocol a protocol to manage network-attached devices. Utilises a MIB to represent the device being managed. Siemens Mobility Traffic Solutions Transmission Control Protocol one of the suite of internet protocols, TCP ensures reliable, in-sequence delivery of data from computer to computer. TELecommunication NETwork an application-layer protocol to exchange TCP connections between computers
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 13 of 197 Released 20 January 2011 667/HB/33930/000

PCB PELV PSTN PSU PWM RAM RCD REC SDS SHS Siespace

Siespace (UVMS) SMDD SMPSU SNMP TS TCP TELNET

Security classification Version Last Editor Document Name

s
UTMC UVMS VPN Urban Traffic Management & Control Urban Variable Message Sign

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Virtual Private Network a term given to the creation of a secure, private point-topoint connection between computers that are, in reality created across open network connections or virtual circuits in some larger network

1.4

REFERENCES
No. 1 Reference 667/UW/33930/000 Title Elektra UVMS System Design Document Version Latest Author Nick Ebsworth, Werner Poppleman, Martin Cable, Fiona Foy, Kevin Napper, Mark Retallack, Paul Weston, Kevin Wass. K.W. Pppelmann Mark Retallack/Jim Ballantine Mark Retallack/Jim Ballantine K.W. Pppelmann C.Rabe Paul Cox, Eric Burdis, Jim Ballantine, Mark Retallack Department for Transport K. Wass

2 3

667/HB/33930/000000 667/HB/31760/000

Production Test Requirements Specification for ELEKTRA - UVMS GVP Reference Manual

Latest Latest

667/HB/31760/100

Outstation Support Server Handbook Display Modules & Lantern HMDD Serial Lantern Module HMDD Gemini2 Traffic Outstation Handbook

Latest

5 6 7

667/SA/33950/000 667/SA/33963/000 667/HB/32600/000

Latest Latest Latest

8 9

ISBN 978 0 11 551958 1 667/CI/44010/000

Safety at Street Works and Road Works Drawing - Multipole Spacing and Brackets

Latest Latest

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

14 of 197 Released 20 January 2011 667/HB/33930/000

s
2

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

PRODUCT GENERAL DESCRIPTION

Elektra is a family of LED variable message signs. They have been designed for use as traffic information signs and for car park guidance.

Multipole Message Sign

Monopole (Cantilever) Car Park Guidance Sign

Figure 1 Typical Elektra Signs A web browser interface is employed for configuration, support and maintenance, which allows these functions to be performed both remotely and locally. This is achieved by utilizing the Siemens Outstation Support Server (OSS) to manage Elektra VMS alongside existing Gemini UTMC outstations. For local connection either a cable or a Bluetooth connection can be used. Configuration changes made at the site can be automatically up-loaded to the OSS, ensuring that a fully up to date set of configurations is maintained. Advanced fault monitoring is incorporated, offering a large range of fault indications which includes monitoring of individual pixels. Elektra is available as a traditional multipole (2 poles) installation or as a choice of two Monopole designs. A simple monopole (Stanchion) design is available or a Cantilever structure which incorporates elevation adjustment (+ 5 degrees).The enclosures have been designed for easy installation and access, with rear access to all components through doors fitted with retaining stays.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 15 of 197 Released 20 January 2011 667/HB/33930/000

s
The following display variants are available:

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Elektra can also provide dynamic guidance by employing directional arrows that can work in conjunction with text legends.

100mm yellow 100mm red/green 160mm yellow 160mm red/green 200mm Graphical arrow (Yellow) 240mm yellow 320 mm yellow 320mm Graphical arrow (Yellow)

Note: all characters in a sign must be the same size (height). All displays have a wide viewing angle which makes installation alignment less critical and improves visibility across the carriageway. Figure 1 shows typical Elektra display configurations
TRAFFIC INFORMATION SIGNS (TI)
Number of Characters
9 Cantilever Multi-pole Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y antilever Y Y Y Y N Y Y Y Y Y Y Y Y N N N 12 Multi-pole Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y 15 Cantilever Multi-pole Y Y Y Y N Y Y Y Y N N N N N N N Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y 18 Cantilever Multi-pole Y Y Y Y N Y Y Y Y N N N N N N N Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y

2 3 4 5 6 2 3 4 5 2 3 4 5 2 3 4

Y Y Y Y Y Y Y Y Y Y Y Y Y N N N

CHARACTER SIZE (mm)

LINES

320

LINES

240

LINES

160

LINES

100

CAR PARK SIGNS (CPGS)


Number of Characters
6 Cantilever Multi-pole Y Y Y Y Y Y Y Y Y Y Y Y Y 12 Cantilever Multi-pole Y Y Y Y Y Y Y Y Y Y N N N Y Y Y Y Y Y Y Y Y Y Y Y Y

2 3 4 5 6 2 3 4 5 6 2 3 4

Y Y Y Y Y Y Y Y Y Y N N N

CHARACTER SIZE (mm)

LINES

240

LINES

160

LINES

100

Figure 2 Typical Elektra Display Configurations

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

16 of 197 Released 20 January 2011 667/HB/33930/000

s
Note

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Display configurations shown in Figure 2 should be taken as a guide only. Some configurations may not be available in all areas of the country (e.g. in areas of high wind speed) or in all configurations (e.g. with and without Top Banners). Also, none of the Simple Mono-pole (Stanchion) configurations are shown as the range of these is particularly sensitive to location and ground conditions. Please contact Siemens Poole for advice on any particular installation / requirement.

Graphical arrows are normally only available on Gar Park Guidance Signs. At the time of writing a maximum of 8 displays are possible. In this context Each text window counts as a single display, regardless of the number of characters Each graphical arrow counts as a single display

Therefore a maximum of four car park displays with individual graphical arrows are possible. Clearly other combinations within the overall limit of 8 displays are possible and will be site specific. Contact Siemens Poole for further clarification if required. Support is provided for a wide range of communications devices and both UTMC and Siemens UVMS protocols can be used for communication with the Instation. The UTMC VMS compliant In-station communicates via SNMP v1 over IP established via an Ethernet link or a PPP connection. The In-station communicates with the sign using a poll-and-response method, with exceptions. The Elektra sign implements UTMC MIB version 3.01. Instation instructions to the VMS are routed via the MIB. The Instation defines an SNMP Manager which communicates with an SNMP Agent in GVP.

UTMC In- station


UTC System

I/O 8

DSL / Fibre
Modem IP Network

PSTN /GSM
Modem IP Network

OSS

Bluetooth
Direct RS232 connection Teraterm, Web or Telnet session

GPRS
Modem IP Network

Service Terminal Computer (Laptop, PDA etc)


Figure 3 - System Communications Overview

SiespaceInstation

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

17 of 197 Released 20 January 2011 667/HB/33930/000

s
3
3.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

CE AND PERFORMANCE
BS EN 12966-1

The Elektra Sign is CE marked in accordance with BE EN 12966-1:2005 +A1:2009. A copy of the EC-Certificate of Conformity, which includes details of the relevant performance classes achieved, is included as Appendix F of this document

3.2

SUMMARY OF KEY PERFORMANCE CHARACTERISTICS

Optical Performance in accordance with BS EN12966-1 Yellow Red Colour C2 C2 Luminance L3 L3 Luminance ratio R3 R3 Beam width B3 (20 degrees) B3 (20 degrees) Uniformity PASS PASS Visible Flicker PASS PASS Ingress Protection Operating Temperature Range IP55

Green C2 L3 R2 B3 (20degrees) PASS PASS

-15 to + 60 degrees C

3.3

EMC PERFORMANCE

The product is tested in accordance with the requirements of BS EN 50293:2001 Electromagnetic Compatibility Road Traffic Signal Systems Product Standard.

3.4

ROHS COMPLIANCE

This product is not RoHS compliant within the terms of the RoHS Directive 2002/95/EC

3.5

WEEE DIRECTIVE

This product meets the requirements of the WEEE directive emphasising re-use in order of: Appliance Components Sub-Assemblies Consumables

Where re-use is not possible, the design incorporates high levels of recovery and recycling.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

18 of 197 Released 20 January 2011 667/HB/33930/000

s
3.6 LED AND LASER CLASSIFICATION

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

LEDs in this product comply with Class 1M of EN 60825-1- This class is safe for viewing directly with the naked eye, but may be hazardous to view with the aid of optical instruments. In general, the use of magnifying glasses increases the hazard from a widely-diverging beam (eg LEDs and bare laser diodes), and binoculars or telescopes increase the hazard from a wide, collimated beam (such as those used in open-beam telecommunications systems).Radiation in classes 1 and 1M can be visible, invisible or both. No warning label is required on the product.

3.7

QUALITY AND RELIABILITY

It is standard Siemens design policy to ensure a reliable product, that wherever possible no parts are stressed at greater than 50% of their rated capacity in normal use. Under fault conditions (e.g. short circuits in cables) some parts may be stressed at more than 50%, but will always remain within their ratings at 85C.

3.8

SUPPORTED CHARACTER SET

The following characters are supported on Elektra signs -

A Z (Upper Case Only) [ ] \ space & ( ) / : ; < 0-9

_ + >

! , =

% . *

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

19 of 197 Released 20 January 2011 667/HB/33930/000

s
4
4.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

SAFETY REQUIREMENTS
SAFETY OF MAINTENANCE PERSONNEL

In the interests of health and safety, when using or servicing this equipment the following instructions must be noted and adhered to: (i) Only competent and/or supervised personnel with relevant technical knowledge and experience, who are also familiar with the safety procedures required when dealing with modern electrical/electronic equipment are to be allowed to use and/or work on the equipment. All work shall be performed in accordance with the Electricity at Work Regulations 1989 or the relevant local, state and government regulations. (ii) Such personnel must take heed of all relevant notes, cautions and warnings in this Handbook and any other Document or Handbook associated with the equipment including, but not restricted to, the following: (a) The equipment must be correctly connected to the specified incoming power supply. (b) The equipment must be disconnected/isolated from the incoming power supply before removing any protective covers or working on any part from which the protective covers have been removed. (iii) Any power tools must be regularly inspected and tested. (iv) Any ladders used must be inspected before use to ensure they are sound and not damaged. When using a ladder, before climbing it, ensure that it is erected properly and is not liable to collapse or move. If using a ladder near a carriageway, ensure that the area is properly coned and signed. (v) Any personnel working on site must wear the appropriate protective clothing, e.g. reflective vests, etc. When working on the sign to replace modules etc, it is recommended that the Mains Supply to the sign be switched off and the master switch locked in the off position. Working on signs frequently involves working at height. In order to carry out such work an operative will require at least one of the following sector scheme competencies in addition to those mandatory for their occupation:

Found05/2 Found 05/3 Found05/1

Use of steps and ladders Erection of Scaffold Towers (If to be used) Mobile Elevating Work Platforms (If to be used)

If Mobile Elevating Work Platforms are to be used the appropriate training and assessment must be carried out before hand.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

20 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The following task based Risk Assessments and Method Statements should also be used as appropriate: Risk Assessments H001 Using Ladders / Steps H002 Using MEWPs (Cherry Pickers) H003 Using Tower Scaffolds H005 Working at Height Method Statements PMS Working at heights PMS The use of work positioning equipment

Regulation 14 of the Electricity at work regulations should also be carefully considered. This states that: No person shall be engaged in any work activity on or so near any live conductor (other than one suitably covered with insulating material so as to prevent danger) that danger may arise unless a)It is unreasonably in all the circumstances for it to be dead, and; b)It is reasonable in all the circumstances for him to be at work on or near it while it is live, and; c) Suitable precautions (including where necessary the provision of suitable protective equipment) are taken to prevent injury. If working live is to be carried out the related task based risk assessments and method statements must be used. These are: Risk Assessments P006 Live Working

Method Statements PMS Live Working Terminating Supply Tails (live working)

When carrying out work on these signs, as part of our risk assessment we must consider if we will be putting vehicle occupants or pedestrians in a hazardous situation. We should consult the following risk assessments and method statements: Risk Assessments T001 Vehicle Parking on Roads (except Motorways & High Speed Roads) T004 Traffic Management - All Purpose & High Speed Roads Method Statements PMS Working on high-speed roads PMS Working on all-purpose roads

It may be that your risk assessment dictates that traffic management is required. If this is the case a competent persons must plan and erect the traffic management with reference to the Safety at Street Works and Road Works Red Book and Chapter 8.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

21 of 197 Released 20 January 2011 667/HB/33930/000

s
4.2

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

ELEKTRA WORKING AT HEIGHT PROVISIONS

Depending on the scale and type of the work to be carried out, the risk assessment should dictate if a MEWP or platform will be required. If the work can be carried out using ladders, the current harnesses, anchor points and ladder straps should be used. Ladder Strap tie-offs are visible on opening of the enclosure as shown in Figure 4. These can be used to ensure that the ladder is securely strapped to the sign. Alternatively the ladder can be tied to the frame as shown in Figure 5.

Figure 4 - Ladder Strap Tie-Off

The ladder securely strapped to the sign Figure 5 - Ladder Tie-Off to frame A work positioning bar is provided to allow the harness lanyard to be attached to the sign. Figure 6 shows how the most recent lanyard grips the bar effectively.

Work positioning bar.

Figure 6 - Work Positioning Bar If heavy items such a transformer or PSU are to be removed from the sign, the appropriate holes in the mounting brackets should be used in conjunction with a lanyard in order to safely lower them from the sign.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 22 of 197 Released 20 January 2011 667/HB/33930/000

s
5
5.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

ELEKTRA EQUIPMENT
ELEKTRA ENCLOSURE EXTERIOR

Figure 7 and Figure 8 show an external view of the sign infrastructure with the sign elements indicated. Antenna Display Power Modem Modules Cable Bluetooth Antenna (Optional) Lanterns

Lanterns

Master Switch Assembly Gemini Transformers or Switch Mode Power Supply Units Figure 7 - Typical Traffic Information Sign Exterior View

Antenna Modem Power Cable Arrow

Display Modules

Bluetooth Antenna (optional) Master Switch Assembly

Display Modules

Gemini

Transformers or Switch Mode Power Supply Unit/s

Figure 8 - Typical Car Park Guidance Sign Exterior View


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 23 of 197 Released 20 January 2011 667/HB/33930/000

s
5.1.1 Mounting options
There are three possible mounting options: Monopole (Cantilever sign) Simple Monopole (Stanchion sign) Multipole Monopole (Cantilever sign)

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The design of the enclosure, with rear fitting doors, allows easy access for maintenance purposes. The enclosure offers protection to IP55 and allows operation over the following temperature and humidity ranges: Temperature range:-15oC to +60 oC Humidity: 0 to 100% condensing

The sign is attached to a Cantilever pole. The pole is attached to the foundation with four studs, and incorporates azimuth (rotational) adjustment of 5 degrees. The top of the cantilever is formed into a frame to support the sign. On the left and right sides of the sign there are two plates that secure the sign to the frame. The top plate is called the swinging arm and the lower plate the lower pivot. The swinging arm allows the sign to be tilted in the vertical plane (elevation adjustment of up to 1.5 degrees (up) or 5 degrees down). There is a hole at the top of the cantilever to accept conduit. The power cable is fed through this conduit and the hollow inside of the cantilever to ground level. See Section 8.2 of this document for detailed installation instructions Simple Monopole (Stanchion sign) The base of the sign enclosure is attached directly to the top of the rectangular hollow section pole. The pole is attached to the foundation with four nuts. Rotational adjustment ( 5 degrees) of the sign is possible after installation, but adjustments to elevation are not possible. See Section 8.3 of this document for detailed installation instructions Multipole The sign is attached to two circular cross section poles, one of which may be belled (restricted to certain sign sizes contact Siemens Poole for details) to house a secondary isolator. The poles are concreted into the foundations. The correct orientation of this type of sign relies on positioning on installation and cannot be subsequently adjusted in either azimuth or elevation. See Section 8.4 of this document for detailed installation instructions

5.1.2 Mains Connection Options


All Elektra signs are fitted with a lockable double pole mains isolator within the Master Switch Assembly (see Section 5.2.2.1). In order to permit sensible and safe connection / isolation of the installation, Siemens recommend the fitting of a secondary, lockable, isolator in the feeder pillar, or similar, supplying the sign. Siemens recommendations are as follows If the distance between the feeder pillar and the sign exceeds 25m a double pole isolator with MCB should be fitted. Siemens part number 667/7/44679/020 is available for this purpose.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

24 of 197 Released 20 January 2011 667/HB/33930/000

s
For some multipole signs, an optional belled pole may be available.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

If the distance between the feeder pillar is less than 25m a double pole isolator without MCB may be fitted. Siemens part number 667/7/44678/000 is available for this purpose. Armoured cable should be used for the connection between the feeder pillar and the sign. Siemens cable, part number 667/4/88346/060 is available for this purpose.

Note

Belled pole option is only available on a limited range of multipole sign sizes. NOT available for Monopole or Simple Monopole mounted signs

In the case of a belled pole, the electricity board cut-out may be mounted on the wooden board within the pole. In this instance Siemens recommends the fitting of double pole isolator 667/7/44678/000 to permit secondary isolation of the sign at ground level. For further detail on mains connection see section 8.5

5.1.3 Power Supply Options and Requirements


Two Power supply options are available on Elektra signs Transformer SMPS

As standard, Elektra signs will be delivered fitted with transformers. If a power factor corrected supply is required there is the option of using Switched Mode Power Supplies in place of the transformers.

Note

If a power factor corrected supply is required this must be specified at the time of ordering the sign.

Where Transformers are used to provide the required 24V the mains supply must comply with the following specification: 230V AC (+10% -13%) 50/60 Hz

Where Switch Mode Power Supply Units (SMPS) are used (giving an improved power factor) the mains supply must comply with the following specification: 100V-263V AC 50/60Hz

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

25 of 197 Released 20 January 2011 667/HB/33930/000

s
5.1.4 Power Consumption

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Important

The power consumption figures supplied here are designed to permit typical useage calculations to be performed. They are NOT intended to permit design decisions on the number of transformers or SMPS required in a specific sign as other factors such as de-rating must be considered.

Module size/type (mm) 100 100 100 160 160 160 240 320 200 Graphical Arrow 320 Graphical Arrow Lantern Row driver Sensor Gemini Heater element (wire)

Colour

Power (Watts)

Comments

Row Drivers

Yellow Red Green Yellow Red Green Yellow Yellow Yellow

2.3W per character 1.15W per character 3.84W per character 2.3W per character 1.15W per character 3.84W per character 3.64W per character 8.12W per character 6.7W

3 character modules 3 character modules 3 character modules 3 character modules 3 character modules 3 character modules Single character modules 1.5 character modules

Must add 1 row driver per sign row Must add 1 row driver per sign row Must add 1 row driver per sign row Must add 1 row driver per sign row Must add 1 row driver per sign row Must add 1 row driver per sign row Must add 1 row driver per sign row Must add 2 row drivers per sign row Figure Includes Row Driver

Yellow

6.7W

Figure includes Row Driver

Yellow Only N/A N/A N/A N/A

20.5W per set, when on 1 1 8 102W when ON

20.5W per pair, one pair on at a time.

Figure includes row driver N/A

One per sign Includes MC35i power Per Heater wire one in small signs, but could be up to five in a large sign

N/A N/A N/A

Figure 9 Typical Power Consumption of Sign Modules Calculating the power requirement of a VMS sign is complicated by the fact that it will vary considerably depending upon the message displayed, whether the lanterns are flashing (if fitted), and the ambient conditions (temperature, brightness) at different times of the day/night. The display power figures given in Figure 9 are calculated on the assumption that 40% of the leds (within the character) are ON at full brightness to give a realistic maximum loading per character for a text display. It is simplest to consider the power requirements in three different areas, P1, P2 and P3 Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 26 of 197 Released 20 January 2011 667/HB/33930/000

s
Background power (P1) P1 = Gemini Power + Modem Power + Sensor board Power Display power (P2) This is the power required by the display elements of the sign

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

This is the power required by the sign control electronics (Gemini), communications equipment, etc

P2 = ((Power per character x number of characters) x number of rows) + (Power per row driver x number of rows) + (Lantern power, if fitted and ON) + (Graphical arrow power, if fitted) Heater Power (P3) This is the power required by the internal heater elements. The heater control in Elektra signs is intelligent and is based on the current temperature and humidity within the sign enclosure. For this reason, and as the power required by heaters can be significant compared to other parts of the sign, it is sensible to choose a reasonable duty cycle for the heaters at different times of the year. P3 = (Power per heater element (wire) x number of elements) x (percentage of time heater expected to be on)%

5.1.4.1

Example Power Calculation Traffic Information Sign

Sign Details 4 rows x 12 (160mm) yellow characters Lanterns fitted 2 x heater elements fitted P1 = Gemini Power + Modem Power + Sensor board Power P1 = 8 + 0 (Modem included in Gemini power) +1 P1 = 9W P2 = ((Power per character x number of characters) x number of rows) + (Power per row driver x number of rows) + (Lantern power, if fitted and ON) + (Graphical arrow power, if fitted)

With lanterns OFF P2 = ((2.3 x 12) x 4) + (1 x 4) + 0 + 0 P2 = 114.4W With lanterns ON P2 = ((2.3 x 12) x 4) + (1 x 4) + 20.5 + 0 P2 = 134.9W P3 = (Power per heater element (wire) x number of elements) x (percentage of time heater expected to be on)% For summer use, assume heaters on 1% of time, for winter use assume heaters on for 30% of time In summer
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 27 of 197 Released 20 January 2011 667/HB/33930/000

s
P3 = 102 x 2 x 1% P3 = 2.04W In winter P3 = 102 x 2 x 30% P3 = 61.2W Summary power requirements for sign Summer, lanterns OFF = 9 + 114.4 + 2.04 = 125.44W Summer, lanterns ON = 9 + 134.9 + 2.04 = 145.9W Winter, lanterns OFF = 9 + 114.4 + 61.2 = 184.6W Winter, lanterns ON = 9 + 134.9 + 61.2 = 205.1W

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.1.4.2

Example Power Calculation Car Park Sign

Sign Details 3 rows x 6 (100mm) red/green characters 1 x 200mm Graphical arrow, yellow 1 x heater element fitted P1 = Gemini Power + Modem Power + Sensor board Power P1 = 8 + 0 (Modem included in Gemini power) +1 P1 = 9W P2 = ((Power per character x number of characters) x number of rows) + (Power per row driver x number of rows) + (Lantern power, if fitted and ON) + (Graphical arrow power, if fitted) Looking at Figure 9 the highest power is required when displaying green characters. As the default colour for a red/green car park sign is green we will calculate the power based on all characters when displaying green. P2 = ((3.84 x 6) x 3) + (1 x 3) + 0 + 6.7 P2 = 78.82W

P3 = (Power per heater element (wire) x number of elements) x (percentage of time heater expected to be on)% For summer use, assume heaters on 1% of time, for winter use assume heaters on for 30% of time In summer P3 = 102 x 1 x 1% P3 = 1.02W In winter P3 = 102 x 1 x 30% P3 = 30.6W Summary power requirements for sign Summer = 9 + 78.82 + 1.02 = 88.84W
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 28 of 197 Released 20 January 2011 667/HB/33930/000

s
Winter = 9 + 78.82 + 30.6 = 118.42W

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

29 of 197 Released 20 January 2011 667/HB/33930/000

s
5.2 THE ELEKTRA ENCLOSURE INTERIOR

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 10 shows a block diagram of an Elektra Traffic Information Sign, showing two rows of six characters, a graphical arrow and 4 lanterns.

Figure 10 - Elektra Block Diagram


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 30 of 197 Released 20 January 2011 667/HB/33930/000

RS422

EMC Filter

RS422

s
5.2.1 Simplified Sign block diagram

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 11 - Sign Block Diagram (Showing only one row and no lanterns) The Gemini unit provides the interface to the instation via a transmission system (in this case GPRS) and controls the sign in accordance with messages received from the instation Luminance level information comes from from the sensor board and allows the Gemini to control the display Pulse Width Modulation in order to set the display brightness appropriate to the ambient light level. Temperature and humidity information also come from the sensor board and allow the Gemini to activate the internal heaters, as required, to minimise condensation. When the instation sends an instruction for the sign to display a particular legend, the Gemini sends the appropriate data to control the displays via the sensor board and row drivers. Fault information passes back to the Gemini from these modules, is sent to the instation and is available through the Web Browser. Appropriate control actions are also taken by the Gemini on the basis of this fault information. The Sensor board, Row driver modules, Display Modules and VLED PSU modules are supplied with 24V derived from either a transformer or SMPS.. In order to avoid unwanted illumination of the displays the row driver boards are able to remove the VLED power from the displays. This will happen for example if the row driver looses communication with the Gemini. The Gemini provides the power supply for the Modem (12V for the MC35 GPRS Modem), and the Gemini itself gains its power from the sign Master Switch Assembly. The Heaters are supplied with 24V derived from the heater transformer. Communication with the lantern boards (if fitted) is achieved via a row driver that is mounted on the first lantern board. CAT6 cabling connects the first lantern to the other 3 in a daisy chain. Two VLED PSU boards are required in total for the 4 lantern boards.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 31 of 197 Released 20 January 2011 667/HB/33930/000

s
5.2.2 Internal sign modules
5.2.2.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Master Switch Assembly - 667/2/44650/000 standard / 667/2/44650/001 fully populated

WARNING: The master switch assembly cover must not be removed until the supply to the master switch assembly has been isolated. The Master Switch Assembly is fitted to the side of the sign interior. It provides the following facilities: Double pole master power switch Master cartridge fuse Heater fuse Single pole sign power switch Maintenance socket MCB Gemini fuse Transformer/power supply fuse (2 additional fuses are fitted where more than 2 transformers/SMPSUs are required). Dual maintenance socket with built in RCD protection Mains EMC filtering Surge protection All live wiring within the master switch assembly can only be accessed by removing its protective cover.

To remove cover, loosen this captive screw pull cover out and up to release

Figure 12 - The Master Switch Assembly

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

32 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 13 shows positions of the different elements that make up the master switch assembly. The numbering corresponds to that used in Figure 15. The Master Switch Assembly photograph has been shown horizontally to aid clarity. The standard build has 1 transformer/SMPSU fuse. Figure 14 shows the other variant that has 3 transformer/SMPSU fuses.

Figure 13 - Master Switch Assembly Identification Standard (667/1/44650/000)

Figure 14 - Master Switch Assembly Identification Fully populated (667/1/44650/001


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 33 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 15 - Master Switch Assembly Circuit Diagram The part numbers are given in Figure 16 Master Switch Assembly Item Master Switch 63A Master Fuse Holder Master Fuse 20A Heater Supply Fuse Holder Heater Supply Fuse 10A Sign Switch Maintenance Socket MCB Gemini Supply Fuse Holder Gemini Supply Fuse 5A Transformer/PSU Fuse Holder Transformer/PSU Fuse 10A Lightning Protection/Varistors Maintenance RCD Socket 30mA Part Number 408/4/97165/002 516/4/97053/002 518/4/90638/004 516/4/97064/000 518/4/90352/004 408/4/97165/002 516/4/97076/006 516/4/97053/000 518/4/90638/000 516/4/97064/000 518/4/90352/004 516/4/00136/000 516/4/02062/000

Unfiltered Neutral

Filtered Neutral

MOVs

1 2 3 4 5 6 7 8

Figure 16 - Master Switch Assembly Part Numbers

Figure 17 shows a Standard Master Switch Assembly with the cover removed. The module containing the Metal Oxide Varistors (MOV) can be seen attached to the DIN rail. Metal Oxide Varistors are electronic components with a significant nonlinear currentvoltage characteristic. When triggered, they will shunt the current created by the high voltage away from the sensitive components. In the case of ELEKTRA signs they protect the sign from high voltage transients that may appear on the mains supply. These transients could be produced by lightning for example.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

34 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Metal Oxide Varistors (MOV)

Figure 17-Master Switch Assembly with Cover Removed 5.2.2.2 500VA Transformer Assembly 667/1/44670/000 The transformer is a 230 V a.c. to 24 V a.c. 500 VA transformer. It is part of an assembly which includes an integral mounting plate that secures it to the sign enclosure. It is heavy with a mass of approximately 10 kg and care should be taken when fitting or removing it. The transformer has four individually fused outputs fixed to its top plate and four common return terminals.

From Master Switch Assembly

10A 230 V 10A 24V 10A 10A Supply to Displays and Lanterns

0V Return from Displays and Lanterns

0V 0V Earth

Figure 18 - Power Supply Transformer

Figure 19 - Transformer Circuit Diagram

IMPORTANT

Note: Although one end of the transformer secondary winding is labelled as 0V, it should never be connected to ground (i.e. any metalwork within the sign), as the supply is referenced to ground after rectification.

The transformer mounting plate incorporates a hole so that a lanyard can be used when removing the assembly from the sign. This enables it to be lowered to the ground safely, avoiding creating a hazard for pedestrian.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 35 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Attach Lanyard

Figure 20 - Transformer mounting plate with lifting hole 5.2.2.3 Switched Mode Power Supply Assembly 667/1/44675/000 Where a Power Factor corrected mains input is required there is the option that the 24V supply is derived from PSU (DC) modules rather than transformers. These are mounted across the base of the sign enclosure. The power supply is cooled by natural convection and is mounted on a bracket to allow air flow up through the unit. The PSU is a lightweight 24V DC switch mode unit as shown in Figure 21. It has four individually fused outputs fixed to its bracket and terminals on its front face for 24V returns and mains connections. 10A fuses are used 518/4/97065/000.

FUSED OUTPUTS

Figure 21 - Switch Mode Power Supply The PSU mounting plate incorporates a hole so that a lanyard can be used when removing the assembly from the sign, so that it can be lowered to the ground safely.

Attach Lanyard Figure 22 - PSU mounting plate with lifting hole

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

36 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.2.4 The Comms Panel 667/1/44630/000 (Includes Gemini) The Comms (Communications) Panel is a sliding aluminium panel upon which the Gemini unit and modem are mounted. These two devices allow communication with the instation. The modem is normally powered from the Gemini. The Gemini connects with the sensor module using an RS422 interface over CAT5 cabling. The sensor module then connects to the first row driver using the same type of interface. The Gemini also connects with the heater and door switches via its IO interfaces. The Comms Panel has been designed to accept other comms/additional equipment required to be mounted within the sign.

GPRS Modem

This area of the Comms panel is designed to accept other equipment

Gemini

Handset Port

Figure 23 - Comms Panel The Comms panel comprises: ELEKTRA Gemini o RS232/422 converter (Mounted as part of Gemini unit and powered from power pins on the Gemini serial port) o Handset Port (allows connection of engineers terminal) o Optional IO card for UTC controlled applications requiring 8 Input and 8 output lines o Battery Backup for Gemini and modem Optional Modem for in-station connectivity one of: o DSL modem (Ethernet) o Fibre modem (Ethernet) o GPRS modem (Serial) o GSM Modem (Serial) o PSTN modem (Serial) o Other modems may be used as required Interface to enclosure door switches Interface to heater control relay

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

37 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The Comms panel can be moved sideways to improve access to the boards behind it. This is done by slackening its four mounting nuts. The position of one such nut is shown in Figure 24.

The position of one of the four nuts that should be slackened in order to adjust the position of the panel.

Figure 24 - Comms Panel adjustment

5.2.2.5 The Antenna The antenna is used when the modem is a wireless module such as GSM or GPRS. It is mounted on a removable plate at the top of the Elektra sign. The plate can be used with a variety of antenna designs through simple modification.

Figure 25 - The Antenna The Light Sensor 667/1/31259/001 The ambient light sensor is mounted on the same plate as the antenna in the top surface of the sign. The light sensor cable connects into the Elektra sensor module.

Figure 26 - The Light Sensor


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 38 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The ambient light level is periodically read from the light sensor by the Sensor board. The current light level is resolved into one of 5 luminance level bands. Luminance control of the displays is achieved by PWM (Pulse Width Modulation) control of the current supply to the LEDs and is dependent on either the luminance level band or luminance override instructions from the In-station (if the sign has been configured to allow the override).

IMPORTANT

Note: As the characteristics of the different types of display are not all the same, the Gemini needs to be configured to take account of the actual displays fitted to the sign. If this is not done, the display intensity levels may be incorrect. This operation is described in section 11.5 with further information on the web pages used given in sections 13.11.4 and 13.11.5.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

39 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The Row driver Module Assembly 667/1/33980/002 The row driver module produces the signalling that drives the LED displays. It is fitted to the rear of the display boards, on the far right of each row when looking from the rear of the sign. Each row has a separate row driver module. The row drivers are connected together with CAT5 cabling. The RJ45 connectors are designated as IN and OUT, and the cabling must be carried out taking account of this. These boards are auto addressed by the Gemini unit. If a rotary switch is present on the board this should be set to 0. Power Output Connection. Can be used to Supply Sensor Board.

See Figure 28 for full description of LED states

Switch

RS 422 to next Row Driver

RS422 from Sensor Board if first row Driver, otherwise from previous row driver

Diagnostic Reset Switch Switch For factory use only

Address The first Row driver is address 11

Figure 27 - Row Driver Module (Front)


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 40 of 197 Released 20 January 2011 667/HB/33930/000

s
LED Fault Run Comms Type On Flash Off Flash Off Flash Fast flash Off Meaning Fault Invalid address No fault Normal operation No power Comms active Downloading No GSPI comms

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Possible Cause Fault present. Fault is indicated until reported over GSPI. Invalid address No fault or no power Normal operation No power or fault GSPI comms present GSPI download in progress GSPI comms lost

Figure 28 - Row Driver LED States

5.2.2.6 The Row Driver 7-Segment Display The 7-segment display is driven to reflect the status of the board and any associated display or lantern boards. The following figures show the state of the display when specific circumstances occur: Local PSU failure or held in reset If the power if off, there is a local PSU failure or the board is held in reset the display remains blank as shown below in Figure 29.

Figure 29 7- Segment blank Unconfigured If the board has powered up and is awaiting allocation of its address the display will be in the state indicated below in Figure 30.

Figure 30 7- Segment dashes

Configured normal working The board is allocated an address from the Gemini. The allocated addresses start from 16 (Decimal) and are displayed in hexadecimal, as shown below in Figure 31(address 17 in decimal).

Figure 31 7- Segment Address Digits It should be noted that these displays output in Hexadecimal, which means that 11 is not Eleven but Seventeen in decimal.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 41 of 197 Released 20 January 2011 667/HB/33930/000

s
16 1 1 1 Figure 32 Hexadecimal Address

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 32 shows that we have (1x1) + (1x16) in Decimal, which equals 17.

Figure 33 below shows the rear of the row driver module. The connector shown passes power and communications between the row driver and display boards.

Connection to Display board.

Figure 33 - Row Driver Module (Rear) If the row driver looses communication with the Gemini or the Display modules, it is able to disconnect the power from the displays.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

42 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.2.7 Sensor module 667/1/33980/001 The sensor module performs two functions; it provides environmental sensing and communications conversion between the Gemini and row driver modules. For the latter function it must always be connected directly to the Gemini unit (RS232/422 converter board). The sensor module has a temperature sensor, humidity sensor and a connector to accept the light sensor. The sensor module and the row driver modules look very similar as they use the same PCB. The part number distinguishes between the two but a quick means of identification is the lack or presence of the connector on the underside of the PCB. The sensor module doesnt have this connector fitted. Once the addresses have been successfully allocated, the sensor module always has the address of 10 (HEX). The output RJ45 connector on the sensor board must connect to the Row Driver board on the first row. These boards are auto addressed by the Gemini unit and if a rotary switch is present on the board this should be set to 0.

Humidity Sensor Temperature Sensor

See Figure 35 for full description of LED states Power Input Connection

Light Sensor Input

RS422 To First Row Driver

RS422 From Gemini Address The Sensor Board is always address 10

Diagnostic Reset Switch Switch For factory use only

Figure 34 - The Sensor Module

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

43 of 197 Released 20 January 2011 667/HB/33930/000

s
LED Fault Run Comms Type On Flash Off Flash Off Flash Fast flash Off Meaning Fault Invalid address No fault Normal operation No power Comms active Downloading No GSPI comms

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Possible Cause Fault present. Fault is indicated until reported over GSPI. Invalid address No fault or no power Normal operation No power or fault GSPI comms present GSPI download in progress GSPI comms lost

Figure 35 - Sensor Module LED States The Gemini software periodically request sensor readings from the Sensor board. The sensor board then returns the values read from the external light sensor and on-board temperature and humidity sensors. To ensure that short duration transients in the light level are ignored the light sensor readings are averaged over a three minute period by the Gemini. The Gemini then sends information indicating the appropriate brightness level to the Row Drivers as part of a broadcast message. If the luminance is changed this occurs synchronously across all Row Driver boards. 5.2.2.8 The Display modules The Elektra sign uses a variety of display module designs. These modules vary in pitch, size and colour. The display modules link together and are controlled by a row driver module which is usually fitted to the first display in the row. They perform LED open/short circuit monitoring, and are fitted to a sunshield assembly. The sunshield ensures the required contrast under direct sunlight conditions, and is mounted in the sign with M8 nut fixings. At the time of writing the following Display PCB assemblies are available: Description 1 2 3 4 5 6 7 8 9 100mm Character PCB Assembly (Yellow) 100mm Character PCB Assembly (Red/Green) 160mm Character PCB Assembly (Yellow Full Matrix) 160mm Character PCB Assembly (Yellow 5x7 Matrix) 160mm Character PCB Assembly (Red/Green Full Matrix) 240mm Character PCB Assembly (Yellow) 320mm (Yellow) = 2 x 160mm Yellow (table row 3) 200mm Graphical Arrow = 2 x 100mm Yellow (table row 1) 320mm Graphical Arrow = 2 x 160mm Yellow (table row 3) Number of Characters 3 3 3 3 3 1 1.5 Arrow Arrow Part Number 667/1/33951/001 667/1/33951/002 667/1/33953/001 667/1/33957/001 667/1/33953/002 667/1/33955/001 667/1/33953/001 667/1/33951/001 667/1/33953/001

The PCB assemblies included in the table do not include PSUs or Sunshields. Kits are available, but from a maintenance perspective it is envisaged that individual PCB assemblies only will be replaced on site.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

44 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.2.9 100mm Character PCB Assembly (Yellow) 667/1/33951/001 Figure 36 shows the front of a 100mm Yellow display module, illustrating that only alternate LED columns are populated.

Figure 36 - 100mm Character PCB Assembly (Yellow) - Viewed from front Figure 37 shows the rear of a 100mm yellow display module, showing the connectors for the VLED PSU and the Row Driver module. The Row Driver is only fitted if this is the first display in a row, and it can be seen that the second VLED PSU connector is omitted as this only has yellow LEDs. LED indicating Power to Yellow LEDs

Connection to adjacent display board

Connection to adjacent display board

Connector for Row Driver Board

VLED PSU Connector


for yellow LEDs

No VLED PSU Connector as only yellow LEDs

Figure 37 - 100mm Character PCB Assembly (Yellow) Viewed from rear The VLED indicates the presence of power for the display LEDs.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

45 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 38 shows a 100mm Yellow display module with a VLED PSU fitted and fitted to a sunshield

Figure 38 - 100mm Character PCB Assembly (Yellow) with VLED PSU fitted

5.2.2.10

100mm Character PCB Assembly (Red/Green) - 667/1/33951/002

Figure 39 shows a 100mm Red and Green display module and illustrates that the LED columns are fitted with LEDs of alternate colour, with all positions being populated.

Figure 39 - 100mm Character PCB Assembly (Red/Green) - Viewed from Front Figure 40 shows the rear of a Red and Green Display module, demonstrating that connectors are provided for two VLED PSUs and that two VLED indicators are provided to show the presence of power to both colours of LEDs.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

46 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

LED indicating Power to Red LEDs

LED indicating Power to Green LEDs

Connection to adjacent display boards

Connection to adjacent display boards

Connector for Row Driver Board VLED PSU Connector VLED PSU Connector for Red LEDs for Green LEDs Figure 40 - 100mm Character PCB Assembly (Red/Green) Viewed from Rear Figure 41 shows a 100mm Red and Green display module with two VLED PSUs and a Row driver fitted, and fitted on a sunshield.

Figure 41 - 100mm Character PCB Assembly (Red/Green) with VLED PSUs and Row Driver fitted. 5.2.2.11 160mm Character PCB Assembly (Yellow Full Matrix) 667/1/33953/001

Figure 42 shows a 160mm yellow Display Module. As with the 100mm module only one VLED PSU is module is required.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

47 of 197 Released 20 January 2011 667/HB/33930/000

s
LED indicating Power to Yellow LEDs

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

No LED as no Green LEDs or PSU module

Connection to adjacent display boards

Connection to adjacent display boards

Connector for PSU Connector Row Driver Board for Yellow LEDs

No PSU Connector as only Yellow LEDs

Figure 42 - 160mm Character PCB Assembly (Yellow Full Matrix) Viewed from Rear

5.2.2.12 160mm Character PCB Assembly(Red/Green) Full Matrix - 667/1/33953/002 Figure 43 shows the rear of a 160mm Red and Green display module, which is fitted with two VLED PSUs and the Row Driver module. As a row driver is fitted, the board pictured is the first in the row and will have no other boards connected to the right (as viewed from the rear). Other boards in the same row will not have row drivers fitted. LED indicating Power to Red LEDs LED indicating Power to Green LEDs

Connection to adjacent display board Row Driver Board

Connection not used in this case as this board will be first in the row Red VLED PSU Green VLED PSU

Figure 43 - 160mm Character PCB Assembly (Red/Green) Full Matrix Viewed from Rear

5.2.2.13

160mm Character PCB Assembly (Yellow) 5 x 7 Matrix - 667/1/33957/001

Figure 44 shows the front and rear of a 160mm 5 x 7 display module, which is populated with LEDs to form 3 distinct character rather than a full matrix. This configuration is only available on 160mm yellow displays. The lower picture shows the connectors for the VLED PSU and the Row Driver module in a similar arrangement to the full matrix 160mm display boards. The Row Driver is only fitted if this is the
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 48 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

first display in a row, and it can be seen that only one VLED PSU position is provided as the board can only have yellow LEDs.

Front

Rear

Figure 44 160mm Character PCB Assembly (Yellow) 5 x 7 Matrix 5.2.2.14 Colour selection on Red and Green Display modules

In normal use, text will be displayed in one of the two colours i.e. Red or Green. This is controlled within the software driving the displays. By default, all text will be displayed in Green. Reddening of special words is enabled and disabled using the Web Browser Special Words Compare Facility option on the StatusConfig->UVMS Library->General configuration page. The special words themselves are defined on the StatusConfig->UVMS Library->Special Words configuration page. If no words are configured then no words will be red. For more details please see the commissioning section (Section 11).

5.2.2.15

240mm Character PCB Assembly (Yellow) 667/1/33955/001

Figure 45 shows a 240mm yellow Display Module with a Row Driver and a VLED PSU module fitted. One VLED PSU module is required for every two boards. The power ribbon cable should only be fitted between boards that share a VLED PSU The first board on each row has a VLED PSU fitted and power is transferred to the second board (which has no VLED PSU) by a ribbon cable. The second board does not have a power connection to the third, which has its own VLED PSU. The third board has a power connection to the forth (which has no VLED PSU).

This sequence repeats and is illustrated more clearly in Figure 80.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

49 of 197 Released 20 January 2011 667/HB/33930/000

s
Data Connection Between boards

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Row Driver one for each row

VLED Power indicator Power Connection Between boards (Ribbon) VLED PSU Module One required for every two Display Modules

Figure 45 - 240mm Character PCB Assembly (Yellow) Viewed from Rear 5.2.2.16 320mm Display (Yellow) 2 x 667/1/33953/001

320mm displays are constructed by tiling two rows of 160mm boards to form a continuous 320mm high LED matrix. Each pair of 160mm boards (vertically stacked) provides 1.5 character width of 320mm text. This means, for example, that 2 pairs of 160mm boards will provide 3 characters of text or for an 18character 320mm row, 2 rows of 12 160mm boards are required. Note that each row of 160mm boards used to construct a 320mm row requires its own row driver.

5.2.2.17

Graphical Arrows

In a similar manner to 320mm displays, it is also possible to tile either 2 x 100mm or 2 x 160mm full matrix display boards to form what is termed as a graphical arrow This is an arrow which may point in any one of eight directions (N, NE, E, SE, S, SW, E, NE as per points of the compass), under control of the instation, in conjunction with text messages set on the sign to provide a context sensitive display. Graphical arrows are only available on Car Park Guidance Signs and only in Yellow.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

50 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 46 - Graphical arrow comprised of 2 x 100mm Character PCB Assemblies These codes can be defined using the web page described in section 13.11.6. A Graphical Arrow is treated as a self contained single row and uses only one Row Driver, with a ribbon cable connecting the two 100mm or 160mm display boards as shown in Figure 47. Figure 47 shows diagrammatically how the Modules are connected to give a Graphical Arrow.

To Other Row Drivers

PSU

ROW DRIVER

24V

PSU

24V

Figure 47 - Graphical Arrow Arrangement - Viewed from Rear

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

51 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.2.18 The VLED PSU 667/1/33966/001 The VLED Display Power Supply board is designed to provide the high-current low-voltage power to the LEDs of each Display module. One Display Power Supply board is fitted to the rear of each monochrome 100/160mm Display module and one PSU for every two 240mm single-display module. Two Display Power Supply boards are fitted to the rear of each dual-colour Display module. There is only one Display Power Supply board variant the voltage that the PSU generates is selected automatically when the board is plugged into the Display board no commissioning is required. This has two benefits: No installation error is possible Only one spare needs to be carried by field services

24V Input

Figure 48 VLED Power Supply Board

This board supplies the following voltages depending upon the application: For 100mm and 160mm yellow or red displays this board supplies 3.52V. For 240mm yellow displays it supplies 6.3V. For lantern modules it supplies 6.3V, For 100mm and 160mm green displays this board supplies 5.36V.

5.2.2.19

Lantern Display Assembly 667/1/44610/800

The Elektra sign has the option to be manufactured with yellow LED lanterns in each corner. The purpose of this is to indicate that the message is of a safety based or warning nature. Only the first of the four lanterns has a row driver module fitted to it and this connects to the other display row drivers using a CAT5 cable. The lanterns themselves are linked together with their own dedicated bus. This uses CAT6 cable. Please see the lantern cabling arrangement diagram.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

52 of 197 Released 20 January 2011 667/HB/33930/000

s
Input to lantern from last Row Driver (CAT 5) Output to other Lantern Modules (CAT 6) Figure 49 - Lantern Module (first) Figure 50 illustrates the main features of a lantern board.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 50 - Lantern PCB 5.2.2.20 Lantern Cabling arrangement Figure 51 shows how the lanterns should be connected. CAT5 cables are used to connect the last display row driver to the lantern row driver, and then the lantern boards themselves are connected using CAT6 cables. All RJ45 connectors are labelled IN and OUT and the cabling must take account of this.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

53 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 51 - Lantern Cabling arrangement Figure 52 provides a diagrammatic representation of this.


Comms CAT 6

Lantern Board

Lantern Board

Comms CAT 6

VLED

VLED

Comms CAT 6 Comms

Lantern Board 24V & VLED PSU Module

Lantern Board 24V & VLED PSU Module 24V

Lantern Row Driver


Comms CAT 5

Last Display Row Driver

Transformer or PSU

Figure 52 - Lantern Block Diagram

Mains

IMPORTANT

It is essential that only CAT 6 cables are used for inter-connecting the Lantern boards where specified. If CAT 5 cables are used then intermittent and unreliable operation will result.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

54 of 197 Released 20 January 2011 667/HB/33930/000

s
5.2.2.21 Display Blanking

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

A Power Enable (POWER_EN) signal is generated by the Row Driver boards and is routed to the PSU boards via the display boards. In the event of a communications failure between the Row Drivers and the Gemini or Display Boards, the Row Drivers force POWER_EN inactive, which turns off all the LED PSUs in that Row and extinguishes the power LEDs on associated the display boards. This situation is recognised by the Gemini (either through loss of communication with the row-driver or through a fault reported by the row-driver) which then blanks the whole sign. Thus it is normal under these circumstances to first see a row extinguished followed by the rest of the sign (the time between these events depends on the cause of the fault and the values of timeouts configured in the Gemini).

5.2.2.22

The Heater

Heater Elements (wires) run along the bottom of all the display rows. These are controlled by the Gemini in response to Temperature and Humidity information collected from the Sensor Board. Connections from PL5 on the Gemini processor board are used to energise a Relay to switch power to the primary winding of a 24V transformer. The secondary of this transformer supplies the heater elements. The Relay assembly includes an LED which illuminates when the relay is energised. Depending on the size of the sign, and therefore the number of Heater Elements fitted, the transformer will be either 150 VA or 500VA (see parts list). Activation LED Heater Relay

Gemini Heater Relay control connections

Heater Element (wire)

Figure 53 Heater arrangement Figure 54 gives the connections used for the Heater Control and the Door Switch.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

55 of 197 Released 20 January 2011 667/HB/33930/000

s
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Processor PL5 N/O output 1 Common 1 N/C output 1 N/O output 2 Common 2 N/C output 2 Input common return Buffered input 1 Buffered input 2 Buffered input 3 Buffered input 4 Buffered input 5 Buffered input 6 Buffered input 7 Buffered input 8

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Function 24V Switched O/P to Heater Relay Coil 24V I/P from Transformer

Cable Colour Orange Orange

Door switch Connection Door switch Connection

Red Red

Figure 54 Gemini I/O connections

The Gemini is responsible for controlling the heater. The simplified flow chart shown in Figure 55 illustrates the decision making process used. For simplicity it does not show hysteresis.

Yes

T > 40C*

Heater OFF

No Yes

No T = Temperature H = Humidity
H > Hum Switching Level

T > Temp Switching Level

No

Yes

Heater ON * The Cut out temperature is shown as 40oC, but is configurable. Figure 55 Heater flow chart (Simplified) Figure 56 and Figure 57 show that there is Hysteresis between the levels at which the heater is turned on and off. This is true for both temperature and humidity. This prevents the heater from turning on and off in quick succession.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

56 of 197 Released 20 January 2011 667/HB/33930/000

s
Temperature must exceed this value X+Y before the heater can be turned off. Heater OFF

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

+Y Configured switching level = X -Y Temperature must fall below this value X-Y before the heater can be turned on.

Heater ON

Figure 56 Temperature thresholds


Humidity must exceed this value X+Y before the heater can be turned on. Heater ON

+Y Configured switching level = X -Y Humidity must fall below this value X-Y before the heater can be turned off.

Heater OFF

Figure 57 Humidity thresholds

5.2.2.23

Door Switches

Each cabinet door has a door switch. These switches are wired in series, and when the doors are all closed this shorts together two Gemini input contacts. When any of the doors are opened the contacts become open circuit and the Gemini indicates to the instation that a door is open. Micro Switch Bracket 667/2/44624/000 Switches One for each door

Figure 58 Door Switch Locations

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

57 of 197 Released 20 January 2011 667/HB/33930/000

s
PL5 Digital I/O Door Micro Switch Cable 667/1/44636/028

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 59 Door Switch Connections to Gemini Figure 60 and Figure 61 detail the connections used for the door switch. Pin 7 8 Processor PL5 Input common return Buffered input 1 Function Door switch Connection Door switch Connection Cable Colour Red Red

Figure 60 Door Switch Connection details

Door Switches PL5 8 7

Figure 61 - Door Switch diagram

5.2.3 The Elektra Gemini - 667/1/32605/102


5.2.3.1 Functionality

The Gemini performs the following major functions: Provides a remote monitoring and control interface to the instation via a suitable modem connected to either the RS232 Modem interface or the 10/100 Ethernet interface. Provides an RS232 interface to the RS232/RS422 converter (Comms Board), allowing pixel data to be sent to the Displays (via the Sensor Modules and Row Driver Modules), and fault data to be received from the Display, Row Driver, and Sensor Modules. Provides an I/O interface to connect input devices such as the door switches and output devices such as the heater control relay. Provides a local monitoring and control interface to the on-site Engineer via an RS232 handset Port by either direct serial connection or via a bluetooth connection. Provides the power supply for the modem.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

58 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Provides a battery-backed means of powering the modem and Gemini during power outage to allow last gasp power status to be communicated to the instation.

Figure 62 shows an ELEKTRA Gemini 2 with the RS232/RS422 board fitted.

Figure 62 - ELEKTRA Gemini 2 with the RS232/RS422 board fitted Figure 63 shows that an ELEKTRA compatible Gemini can easily be identified by the additional memory situated on the processor board.

ELEKTRA Gemini 2 with additional memory (total 16Mb)

Gemini 2 without additional memory (total 4Mb), cannot be used as part of ELEKTRA.

Figure 63 Identifying the correct Gemini Unit

Key 230 V Comms 12V

Figure 64 Gemini Interfaces


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 59 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.3.2 Gemini Mains Supply The Gemini is supplied from a 5A fuse located in the Master Switch Assembly. The mains connects to the Gemini on pins 1,2 and 3 of the PSU connector. Gemini PSU Connector (PL1)

Gemini Mains Supply

Figure 65 Gemini Mains Connections

IMPORTANT

Ensure that the Earth lead is securely connected to the Earth Terminal Block and PL1.

5.2.3.3

Support Batteries

The Gemini is fitted with a rechargeable battery which supports the entire unit including the modem, for a minimum of four minutes under all conditions in order that the Outstation may inform the Instation of a mains power failure. This battery must not be operated in the inverted position (i.e. with the terminals pointing downwards). A Lithium coin cell battery is provided on the CPU and supports the RAM memory and the Real Time Clock during power failures for in excess of 7 months. The processor board also has a Gold Cap capacitor fitted that allows the RAM battery to be changed without loss of RAM data. The Gold Cap device provides a minimum of 30 minutes support. The two batteries have the following specifications: Battery Unit Battery RAM Battery Type 12V Lead Acid 418/4/42314/010 Lithium 418/4/53433/000 Support Minimum 4 minutes (20 minutes typical) In excess of 7 months after the main support battery has expired.

Figure 66 Gemini Battery Details 5.2.3.4 The Processor Card The main features of the Processor card are: Battery backup of the entire RAM. An Expansion Bus for fast card-to-card data transfers. The Processor card can address up to three IO cards. Three programmable RS232 Serial communications Ports: Handset RS232 Port. Auxiliary RS232 Port. Modem RS232 Port. A battery backed Real Time Clock. Flash memory for program storage and Journaling File system.
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 60 of 197 Released 20 January 2011 667/HB/33930/000

Security classification Version Last Editor Document Name

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Zero-Cross Over signal derived from the associated PSU support PCB. Power Fail monitoring (low voltage inhibit) A Watchdog monitor Processor error indication Voltage Regulation (allowing a range of DC input) Power for the modem, with a choice of two voltages Status LEDs Power dissipation less than 100 mW

Figure 67 Gemini LED Indicators The three LED indicators on the Processor card give the following status or fault indication: LED Name System LED (GREEN) State OFF Slow Flash (on for 1 sec, off for 2 sec) Fast Flash (on for 1/4 sec, off for 1/2 sec) Heart Beat (two flashes in 1 second, then off for 1 second) Fading up and down in brightness ON Steady OFF Brief flashes ON with brief flashes OFF OFF ON Indication No power or Processor error Normal operation A fault has been detected check the Fault Table screen on the web interface. Main software not executing. Running bootloader and waiting local software update.

Communications LED (GREEN)

Watchdog LED (RED)

Main software not executing. Running launcher program and waiting local software update. Processor error No data being received from the network Communications traffic Communication established and under control of the instation The Processor is running and keeping the watchdog triggered. The hardware watchdog has timed out sometime in the past. When illuminated, this does not mean that the unit is currently in a watchdog state. To clear: Hold down the Processor card Reset button for 2 seconds.

Figure 68 Gemini LED interpretation


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 61 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.3.5 Isolated Outputs The Elektra Gemini is equipped with relay isolated outputs (two change-over contacts). One of these outputs (N/O output 1) is used to control the heater relay. The following table gives the electrical characteristics of the outputs: Processor card Output On Output Impedance Off Output Impedance Continuous Current Sink Breakdown Voltage Isolated Voltage Relay Type Notes:

182 1%, 0.1 Watts 100k min. 50mA 1500V 1500V Change-Over

The continuous current sink is limited by the resistors.

Figure 69 Gemini Output Specifications 5.2.3.6 Digital Inputs The Processor card supports 8 x TR2500 compliant digital inputs. One of these inputs (Buffered input 1) is used to monitor the state of the door switches. These digital inputs have the following input electrical characteristics: Processor card Inputs Input Impedance Off Threshold On Threshold Recommended Max. Voltage Absolute Max. Voltage Isolation Voltage * Referenced to 13.8V Figure 70 Gemini Input Specifications 4300* > 50k < 600 n/a +1kV / -7V 2500V RMS

5.2.3.7 Additional IO Board for Parallel UTC Interface When Elektra is to be controlled using the parallel IO (UTC) interface, it is necessary to add an additional IO board (WEZ I/O part number 667/1/31124) to the Gemini. The IO signals controlling the sign are connected as shown in Figure 71. Figure 71 shows a WEZ I/O board fitted to the Gemini 2. The correct address switch settings are illustrated, and the Input pins are identified (only the first 4 pins are illustrated, however the remaining pins follow the same arrangement identifies the pins to which the 8 bit word can be input.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 62 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

PL1

Pin 1 Pin 2 Pin 4 Pin 3

Figure 71 - WEZ I/O Board

Pin 1 2 3 4 5 6 7 8 25 26 Figure 72 - Digital input pins

PL1 Buffered Input 1 Buffered Input 2 Buffered Input 3 Buffered Input 4 Buffered Input 5 Buffered Input 6 Buffered Input 7 Buffered Input 8 Input Common Ret Input Common Ret

5.2.3.8

The RS232/RS422 Converter

This small PCB is supplied as part of the Elektra Gemini and takes +5V directly from Gemini serial port. The current required is approximately 50mA. The functions and features of this module are as follows: Converts from RS232 to RS422 at the same baud rate. (Maximum Baud rate 1M Baud) Power input on 20-pin IDC connector Optional power input on separate 3-pin connector. Optional linear voltage regulator, allowing operation from voltages higher than 5V DC RS422 output and power available on RJ45 connector Optional screw-terminal connection for RS422

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

63 of 197 Released 20 January 2011 667/HB/33930/000

s
RS422 RJ45 Connecter SK1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

PL3

RS232/RS422 Converter Board

Figure 73 RS 232/422 Converter

PL4 RS232 Communications and Power between Gemini and RS232/RS422 Converter board 667/1/33990

The RS232/422 converter has 2 front-panel LEDs with the following Status/Fault indications: Invalid LED (Red) Off no power or running OK. On steady invalid RS232 levels on input (Gemini turned off or RS232 cable unplugged or faulty)

Invalid LED

Power LED

Power LED (Green) Off no power On steady power present (+5V) Figure 74 RS 232/422 Comms Module LEDs

5.2.4 Direct/Local Connection and Security


The Signs will be assembled in the factory to support one of two local handset connection options as follows: Direct RS232 serial link Bluetooth link Both links are serviced via the RS232 serial port on the front of the Gemini CPU card.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

64 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.4.1 The RS232 Communications Link It is possible to access two types of interface over the RS232 communications link: the WIZ text based configuration interface and the web interface. To access the WIZ interface a connection should be made at one of the following baud rates: 57600, 19200, 9600, 1200 (all 7 bits, even parity). To access the web interface the GeminiConnect Tool should be used. Full details on using both the WIZ interface and the GeminiConnect Tool are given in the GVP Reference Manual (667/HB/31760/000). The WIZ interface allows access to only a subset of Elektra's capabilities. The web interface should be used to access the full configuration, monitoring and maintenance capabilities. The recommended USB to Serial Cable is the Lindy 42812. If communication problems are experienced with this cable when using the GeminiConnect tool, try running GeminiConnect setup again. This will set the correct baud rate which may have changed from the required value (115299). 5.2.4.2 Bluetooth Communication Link The Bluetooth link is routed from the Gemini handset port to a Bluetooth Module located on the outside of the rear of the sign enclosure (on the right hand side when viewed from the rear). The handset facility supports a Web page and a Telnet interface and is accessed via a Bluetooth enabled laptop. The Gemini Connect Tool is used, and a username and password are required to establish the connection.

Bluetooth connection to the handset port.

Bluetooth antenna on the rear of the sign enclosure. Figure 75 Bluetooth Link

View of the Bluetooth Module from inside the sign, showing cable routing and securing nut.

5.2.4.3 Instation Remote Connection The sign is assembled to support one of two remote connection options as follows: RS232 serial link (to GPRS modem or GPRS router). Ethernet connector (to DSL / fibre modem )

Modem Port

Ethernet Port

Figure 76 Ports for Instation Communication Both links are available towards the rear of the Gemini processor card.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

65 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.4.4 Remote Access to Web Pages To be able access the sign web pages from a remote location the connecting network must transfer Port 80 from the sign to the computer running the web browser. This is the case in most installations where sign is controlled using the UTMC protocol but is not the case in most installations where the sign is controlled using the UVMS protocol. Note that these are generalisations and in both cases it is possible for the network to be configured such that the web pages are or are not accessible remotely. If remote access to web pages is required then care should be taken to ensure that Port 80 is transferred across the connecting network. If this network is public at any point then care should be taken to ensure that the communications remain private. The implication of not having a remote management interface is that all Gemini configuration would need to be carried out on site. 5.2.4.5 The Modem Power Supply The Processor card (PL3) normally provides the modem power. Two voltage supplies are available on this card 5V (400mA) and 12V (1000 mA). Insertion of the modem power lead into the relevant connector socket in the Modem Power connector PL3 selects which supply is used as follows: Cableform Position PL3 Socket 3 PL3 Socket 2 PL3 Socket 1 Voltage Supply 5V Supply 12V Supply 0V Supply Modem Type Dynalink PKS-5600-A-P/M GPRS/GSM TC35

Connections for the MC35 Modem

Green and White Blue Figure 77 - Modem Power Supply Connections C

IMPORTANT

Before connecting the plug into the modem with the unit powered up, check with a multi-meter that the correct power supply selection has been made.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

66 of 197 Released 20 January 2011 667/HB/33930/000

s
MC35 GPRS Modem

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

5.2.4.6 The MC35 GPRS Modem This is the GPRS modem currently being used. Other types of modem may be used in the future.

Figure 78 MC35 GPRS Modem The Siemens MC35 Terminal unit is a GSM modem capable of GPRS transmission. The MC35 supports GPRS transmission up to 21.4Kbps per time slot. Interfaces to the unit include an RS232 data port, power and an FME (male) aerial connector. An integrated SIM card reader is included. A diagnostic LED shows the current state of the unit.

The MC35 Diagnostic LED is used to indicate the following states. Operating State Immediately after power up Network Search or no SIM card inserted or no PIN entered or no GPRS network available Found GSM network - ready to connect Found GPRS network - ready to connect Data Transfer LED On for 2 seconds Flashes approx 2 seconds on 2 seconds off

Flashes once every 4 seconds Double Flash every 4 seconds Flashes on for 1 second when data is transferred (this usually replaces the single flash every 4 seconds).

Figure 79 MC35 GPRS Modem LED Indications If it is initially not possible to achieve communications on the GPRS network, the RJ12 power connector should be disconnected and then re-inserted.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

67 of 197 Released 20 January 2011 667/HB/33930/000

s
6 ELEKTRA CONNECTIVITY
ROW DRIVER BOARD LANTERN LANTERN

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

VLED

IN

VLED PSU

MODEM COMMUNICATIONS CONNECTION

DISPLAY #04

ROW DRIVER 01

ROW DRIVER 02

ANTENNA

MC35i

TO NEXT ROW, OR IF LAST ROW, TO FIRST LANTERN

DISPLAY #01

MODEM POWER

COMMUNICATIONS CONNECTION

DISPLAY #02

DISPLAY #05

SENSOR BOARD

IN

OUT

DISPLAY #03

DISPLAY #06

VLED PSU

VLED PSU

Heater Wire

Heater Wire

Heater Transformer

LANTERN COMMS

24V

SWITCH MODE SUPPLY

POWER

POWER

DATA BUS

DATA BUS

OR

MAINS SUPPLY

DATA BUS

DATA BUS

Relay

COMMS BOARD

LANTERN

VLED

Figure 80 - Elektra internal connectivity 240mm This shows a diagrammatic representation of the connectivity within an Elektra LED messaging sign (240mm characters) when viewed from the rear. The diagram shows two rows of three display modules and 4 lanterns. Note: The sensor board can be fitted to any display board as unlike the row driver board it does not have a direct connection to the display board.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 68 of 197 Released 20 January 2011 667/HB/33930/000

VLED PSU

TRANSFORMER

LANTERN

MAINS SUPPLY

Heater Switching Output Door Switch Input

VLED PSU

IN IN

LIGHT SENSOR

IN IN

VLED PSU

POWER

DATA BUS

POWER

DATA BUS

Gemini

MAINS SUPPLY

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 81 - Elektra internal connectivity 100mm / 160mm Yellow This shows a diagrammatic representation of the connectivity within an Elektra sign with yellow LEDs. It is viewed from the rear and shows 2 rows of 2 display modules.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 69 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 82 - Elektra internal connectivity 100mm / 160mm R&G This shows a diagrammatic representation of the connectivity within an Elektra LED Car Park Sign with Green and Red LEDs. It is viewed from the rear and shows 2 rows of 2 display modules.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 70 of 197 Released 20 January 2011 667/HB/33930/000

s
7

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

ELEKTRA SITE PRE-OPERATION PROCESS

The Elektra product has to go through several sequential stages before it can become operational. These sequences are summarised by the flow chart in Figure 83.

Figure 83 Pre-operation chart

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

71 of 197 Released 20 January 2011 667/HB/33930/000

s
7.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

FOUNDATIONS AND POLE INFRASTRUCTURE

The foundations have to be poured and any ducting provided. The size of the foundations depends on the size and weight of the sign, geography (altitude, prevailing wind conditions) and the geology of the ground (sandy soil, clay require different foundations). The foundations will be designed in an early part of the project. Foundation designs are verified by qualified structural engineers and are performed individually for every sign location. This manual does not cover the construction of the foundations or assembly of the poles, although some generic detail is included in Section 8 of this document . Both of these processes are generally subcontracted as these are specialist activities outside the normal capabilities of the Siemens field service teams.

7.2

INSTALLATION FIRST FIX

Installation can commence once the site infrastructure is in place. This includes foundations, sign support poles, ducting and electricity feeder pillars. The installation process doesnt require any power supplied on site. At the end of the installation the sign will have been erected, secured to the poles and any cabling from the sign ducted down the poles. No electrical connections will be made off during this phase. This activity is generally sub-contracted to the same organisation that erected the poles.

7.3

ELECTRICITY CONNECTION

This process is performed by the electricity utility supplier or their contractors and doesnt require Siemens field services to be present. This process culminates in a fused electricity cut-out being fitted to the electricity feeder pillar / bell pole.

7.4

INSTALLATION SECOND FIX

The second fix of installation is normally performed by the Siemens field service group. A prerequisite of commissioning is that the electricity supply must be connected before this phase can be commenced. During this process basic electrical tests will be done to confirm the sign is safe to be connected to the electricity supply. The sign cabling is wired to the electricity feeder pillar and the sign is powered up. Energised tests such as polarity and earth loop impedance must then be performed. If the test results comply with the required values, the operative checks for basic operation and the sign is left powered so that the heaters are operational to prevent internal display fogging or condensation which might be damaging to the internal electronics.

7.5

COMMISSIONING

Commissioning consists of setting any configuration in the product that is specific to site. Instation configuration, communications testing and system testing are also performed as part of this activity. This activity is normally carried out by the Siemens Applications Engineering Group.

7.6

CUSTOMER SITE ACCEPTANCE TESTING

This is a witnessed functional test of the variable message sign to prove correct operation and specification. This is performed at the sign site and at the instation. The witness is the customer or the customers representative. This testing usually follows a documented test plan written by or agreed by the customer. This activity is normally carried out by the Siemens Applications Engineering Group although they may delegate this responsibility to a suitably qualified Siemens Project manager on occasion.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

72 of 197 Released 20 January 2011 667/HB/33930/000

s
8 INSTALLATION

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The installation method will vary depending on which mounting option is chosen for the sign (Monopole (Cantilever), Simple Monopole (Stanchion) or Multipole).

8.1

GENERAL TORQUE SETTINGS

The level of torque to be used during installation to tighten the nuts is dependent on the nut size. The values required are as follows: M30 1350 Nm M24 660 Nm M20 - 380 Nm M16 - 190 Nm M12 - 75 Nm

8.2

MONOPOLE SIGN

8.2.1 Installation of foundation and Anchor Frame


A foundation drawing will be supplied showing the required position and mounting of the Anchor Frame which provides the interface to the cantilever. This must be correctly positioned in the foundation and the concrete allowed to set fully, prior to installation of the cantilever and sign. Note that any cabling for the sign (mains and/or signal) has to feed up the centre of the (hollow) cantilever. It is essential to run ducting from any feeder pillar and / or communications equipment into the foundation with draw rope(s) present during the foundation works.

When arriving at site to install the cantilever the mounting studs, with their associated nuts, should be visible securely located within the foundation.

8.2.2 Cantilever erection


The sign is delivered to site with the cantilever and sign enclosure as separate items. Position the cantilever so it is lying on the ground with the base next to the foundation plinth. Thread a fish tape through the conduit hole in the top of the cantilever until it protrudes from the base. Tie the end of the draw rope coming out of the plinth cable duct to the end of the fish tape. Pull the fish tape through the cantilever with the draw rope on the end of it and knot off the draw rope.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

73 of 197 Released 20 January 2011 667/HB/33930/000

s
1 2

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 84 Threading the Draw Rope through the cantilever Remove the template (top plate) and re-fit the nuts, levelling as appropriate with a small spirit level. Lift the cantilever and lower it onto the foundation plinths bolts. Ensure that the draw rope is tight and doesnt get trapped during this operation. 1 2 3

Figure 85 - Erecting the Cantilever Add the four nuts to secure the cantilever to the foundation. Check that the cantilever is vertical making minor adjustments to the upper and lower nuts as necessary. 1

Figure 86 - Checking the Cantilever is Vertical Adjust the position of the cantilever by rotating it left to right so that the sign (when fitted) will point to the correct point on the road carriageway. Tighten the nuts to the required torque (see section 8.1). Fit and tighten the lock nuts. Optionally bind the nut and bolt heads with tape to keep the threads clear of debris.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

74 of 197 Released 20 January 2011 667/HB/33930/000

s
8.2.3 Fitting the sign to the cantilever
Loosely attach the two (upper) swinging arm plates to the cantilever frame.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The sign will be delivered with two M16 eye-bolts fitted to the top surface for lifting.

The lower pivot plates may have either holes or slots in them to mount the sign, for design reasons, and the process of hanging the sign is slightly different for each type. If the lower pivot plates have slots in them, proceed as follows Insert the two lower bolts and washers into the sign, and adjust them so that there is approximately 25mm free thread showing. Lift the sign using the eye bolts and position it next to the cantilever frame. Lower the sign carefully so that the already fitted bolts drop into the slots on the lower pivot plates. Ensure that the sign pivots with the bolts at the bottom of the slots and hand tighten the bolts. Add the bolts to the two swinging arm plates, reduce tension on the slings and adjust the vertical angle as required. Tighten all the bolts to the required torque (see Section 8.1).

If the lower pivot plates have holes in them, proceed as follows Position the sign enclosure between the two lower pivot plates and insert the bolts and washers. Hand tighten the bolts. Add the bolts to the two swinging arm plates, reduce tension on the slings and adjust the vertical angle as required. Tighten all the bolts to the required torque (see Section 8.1). 1 2 3

Figure 87 - Fitting the Sign Enclosure to the Cantilever The sign will now be secured to the cantilever frame. Remove the lifting gear.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 75 of 197 Released 20 January 2011 667/HB/33930/000

s
IMPORTANT

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Remove the eye-bolts from the top of the sign and stow within the sign to allow them to be fitted if the sign needs to be lifted in future.

On removing the eye bolts, be sure to replace them with the supplied bolts and fibre washers to prevent water from entering the sign. Do not work underneath the sign at any time when it is supported from lifting eyes.

IMPORTANT

Loosen bolts, adjust angle of sign then fully tighten bolts

Figure 88 - Cantilever Sign Elevation Adjustment

8.2.4 Connection of mains cable


See section 8.5.1

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

76 of 197 Released 20 January 2011 667/HB/33930/000

s
8.3 SIMPLE MONOPOLE 8.3.1 Installation of foundation and Anchor Frame

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The Simple Monopole sign shares a common foundation mounting arrangement with the cantilever sign. Refer to Section 8.2.1 for full details.

8.3.2 Stanchion erection


The Simple Monopole sign has a much simpler mounting arrangement than the cantilever sign. The pole bolts directly to the base of the sign enclosure. The pole is installed onto the foundations in the same way as the cantilever (Section 8.2.2). From this point on the process is different.

8.3.3 Fitting the sign to the stanchion


The sign will be delivered with two M16 eye-bolts fitted to the top surface for lifting. Lift the sign using the eye bolts and position it slightly above the pole. Do not work underneath the sign at any time when it is supported from lifting eyes.

IMPORTANT

The draw rope (or mains cable) will be protruding from the top of the pole. Open the door of the sign enclosure. Feed the rope / cable into the hole in the bottom of the sign enclosure. Manipulate the sign so that the four holes in its base align with the corresponding holes in the pole. Fit the supplied anti-vibration washers to the bolts and insert bolts up through the holes in the stanchion top plate and into the sign.. Tighten nuts to the required torque (See Section 8.1). Remove the eye-bolts from the top of the sign and stow within the sign to allow them to be fitted if the sign needs to be lifted in future.

IMPORTANT

On removing the eye bolts, be sure to replace them with supplied bolts and fibre washers to prevent water from entering the sign.

8.3.4 Connection of mains cable


See section 8.5.1

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

77 of 197 Released 20 January 2011 667/HB/33930/000

s
8.4 MULTIPOLE 8.4.1 Installation of Poles

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

On Elektra signs the poles are always placed towards the sign edges in order to permit the maximum possible maintenance access via doors on the rear. Regardless of the size of the sign, there will only ever be two mounting poles for a multi-pole Elektra sign. This places restrictions on the placing of poles, which must be very accurately positioned. For details on the required positions of poles Siemens drawing 667/CI/44010/000 should be consulted. It will be necessary to know the width and height of the Elektra sign to be installed, and then all the information relating to the position (including tolerance) of the poles may be calculated / established from this drawing. To obtain a copy of this drawing 667/CI/44010/000 please contact Siemens Poole. Depending upon the size and location of the sign, one of three pole diameters will be specified: 139.7mm dia 168.3mm dia 193.7mm dia

This can only be finalised after a site survey and subsequent confirmation from an approved structural consultant. This will normally be done after an order has been placed, but in some circumstances may be done at tender stage. If there is any doubt as to the required pole diameter or position please contact Siemens Poole.

8.4.2 Installation of Sign


Prior to the install, the site area will have been prepared with hard-standing for the delivery vehicle. The foundations will have been prepared, poles erected and ducting provided with cable draw ropes present. The sign is fixed to the poles using four U-bolts. The U-bolts interface with slotted brackets which are fitted before the sign leaves the factory. 1 2

Figure 89 - Location of U-Bolt Brackets (View from front of sign)


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 78 of 197 Released 20 January 2011 667/HB/33930/000

s
Lifting points

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The upper U-bolt brackets incorporate holes for the attachment of lifting shackles. The sign should only be lifted from these points. Suitable shackles must be fitted to these points prior to lifting the sign. One shackle should be fitted to the upper left hand bracket and one to the upper right hand bracket DO NOT attempt to lift the sign from one end only.

Figure 90 Multipole sign lifting points With the sign suitably supported, and before lifting the sign into position, loosely assemble the upper Ubolts with their associated parts (as supplied) to the brackets on the sign.

IMPORTANT

Do not work underneath the sign at any time when it is supported from lifting eyes. Ensure suitable chocking / blocks etc in place at all times.

Pole clamp Nordlock washer Nut

Figure 91 - Upper U bolt assembly


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 79 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Lift the sign into position slightly above the final mounting height such that it may be lowered into position with the upper u-bolts around the poles. Care should be taken not to scratch the poles during this operation..

Figure 92 - Lifting sign into position Ensure the enclosure is level and at the correct height then loosely tighten the nuts on the upper U-bolts. Take the Pole Clamps for the lower u-bolt assemblies and, without placing hands or fingers between the sign and pole at any time, position them behind the sign and loosely fit lower U-bolts, washers and nuts.

IMPORTANT

Do not place hands between the pole and the sign during this fitting operation. Locate packing blocks between sign and pole to keep the parts apart during this operation

Figure 93 - Lower U-bolt assembly


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 80 of 197 Released 20 January 2011 667/HB/33930/000

s
Fully tighten upper U-bolt nuts to the required torque (see section 8.1).

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

When both lower U-bolts are loosely fitted, fully tighten U-bolt nuts to the required torque (see section 8.1).

Having released the tension on the lifting strops, remove the shackles from the upper U-bolt brackets . 1

Figure 94 - Multipole enclosure fitted to the Poles

IMPORTANT

Do not work underneath the sign at any time when it is supported from lifting eyes. Ensure suitable chocking / blocks etc in place at all times.

8.4.3 Connection of mains cable


See Section 8.5.1

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

81 of 197 Released 20 January 2011 667/HB/33930/000

s
8.5 ELECTRICITY CONNECTION

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The REC/DNO should be asked in advance by the customer to provide the supply including the cut-out during the first-fix period. If the supply is not present, field services may have to contact the customer to ensure that the supply is provided. All Elektra signs are fitted with a lockable double pole mains isolator within the Master Switch Assembly (see Section 5.2.2.1). In order to permit safe and sensible connection / isolation of the installation, Siemens recommend the fitting of a secondary, lockable, isolator in the feeder pillar, or similar, supplying the sign. Siemens recommendations are as follows If the distance between the feeder pillar and the sign is less than 25m a double pole isolator without MCB may be fitted. Siemens part number 667/7/44678/000 is available for this purpose. If the distance between the feeder pillar and the sign exceeds 25m a double pole isolator with MCB should be fitted. Siemens part number 667/7/44679/020 is available for this purpose. Armoured cable should be used for the connection between the feeder pillar and the sign. Siemens cable, part number 667/4/88346/060 is recommended for this purpose.

Copex Trunking

Gemini

Within enclosure Supply to Master Switch Master Switch Armoured power cable Inside pole

Armour termination

Feeder Pillar

Secondary Isolator Cut-Out

REC/DNO cable

Figure 95 - Mains Connection Scheme


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 82 of 197 Released 20 January 2011 667/HB/33930/000

s
For some multipole signs, an optional belled pole may be available.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Note

Belled pole option is only available on a limited range of multipole sign sizes. It is NOT available for Monopole or Simple Monopole mounted signs

In the case of a belled pole, the electricity board cut-out may be mounted on the wooden board within the pole. In this instance Siemens recommends the fitting of double pole isolator 667/7/44678/000 to permit secondary isolation of the sign at ground level. Access to a belled pole is with a tri-head key. The Earth Loop Impedance calculations in this handbook are based on an Isolator fuse rating of 25A.

8.5.1 Fitting and Termination of Mains Cable


Elektra signs may or may not be supplied with mains cable already attached to the sign, depending upon installation requirements at individual sites. 8.5.1.1 Mains Cable Supplied With Sign

Figure 96 - Mains Cable Interface to Pole In this case, the cable will have been fully terminated within the sign before leaving the factory. All that is required on-site is the connection of the cable to the electricity supply. Uncoil the cable, and fit a suitable length of flexible trunking (copex Siemens Part number 915/4/10315/004 is recomended)) over the cable followed by a gland suitable for the hole in the pole(Siemens part number 915/4/10316/000 is recomended) Attach a draw rope to the cable. Check Risk Assessment and if safe to do so pull the cable through into the feeder pillar (G39 Authorisation required if cut-out installed in feeder pillar). Fit gland to pole and ensure flexible trunking pushed into gland to effect water resistant seal. If not already done so, mount the relevant double pole isolator (see section 8.5 above) adjacent to the electricity board cut out in feeder pillar. Connect the sign to the output side of the isolator but do not connect the input side to the electricity supply until the tests described in section 10 have been performed.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 83 of 197 Released 20 January 2011 667/HB/33930/000

s
IMPORTANT
8.5.1.2 Mains Cable Not Supplied With Sign

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The feeder pillar / belled pole may only be accessed by an operative who is G39 trained and DNO/REC Authorised

In cases when the cable is not supplied with the sign it must be pulled into place during installation of the poles, it will then be available for final connection during installation of the sign. For a multipole sign this cable will be left coiled at the top of one of the poles, whereas for a Monopole or Simple Monopole it will be left coiled at ground level. When providing the cable in this manner, it is important to leave sufficient cable length available for connection to the sign For a Multipole sign a good rule of thumb is to leave a length of spare cable equal to the height of the pole above ground level. For a Monopole or Simple Monopole sign a good rule of thumb is to leave a spare length of cable (at ground level) equal to twice the final height of the top of the sign. The cable should be left suitably coiled to prevent damage prior to installation of sign.

The process for connection of the cable to the sign varies slightly with mounting option but is similar in each case. Multipole Uncoil cable at top of pole and if not already done pull cable through the gland hole in the pole. Fit a gland suitable for hole in pole (Siemens part number 915/4/10316/000 is recommended) over the cable followed by a suitable length of flexible trunking (copex Siemens part number 915/4/10315/004 is recomended) over the cable. Feed the cable carefully through the gland on the rear of the sign.

IMPORTANT

There are many delicate electronic components on the rear of the circuit boards in the sign. Extreme care must be taken when feeding the cable through not to damage any of the boards.

Once the cable is fed through and into the sign, fix the gland to the pole and push flexible trunking into both glands to effect a water resistant seal. Inside the sign, route the cable to the gland plate situated just inside the nearest door to the incoming cable gland. Hold the cable against the gland plate and estimate the length of outer insulation and armouring to remove. Strip cable armouring back for length as determined above. Fit armoured gland to cable and locate on gland plate as shown in Figure 97

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

84 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Gland Plate

Figure 97 - Mains Cable Gland Plate

Run the stripped cable from the gland plate to the master switch unit. Connect L, N and E cables as shown in Figure 98

Live

Neutral

Earth to primary earth point

Figure 98 - Mains Cable Connection Monopole In this case, the cable must be fed up the cantilever pole and out through the gland hole when it is lying on the ground before it is lifted into position (See section 8.2.2)

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

85 of 197 Released 20 January 2011 667/HB/33930/000

s
Simple Monopole

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Once the cantilever and sign are installed, the process is the same as for the Multipole sign described above.

In this case, the cable must be fed up the stanchion when it is lying on the ground before it is lifted into position. As the sign is lifted into place the cable must be fed into the base of the sign.

IMPORTANT

There are many delicate electronic components on the rear of the circuit boards in the sign. Extreme care must be taken when feeding the cable through not to damage any of the boards.

Once the sign is fully fixed to the stanchion the cable is routed in a similar manner to that described above and connected to the Master Switch unit.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

86 of 197 Released 20 January 2011 667/HB/33930/000

s
9 INSTALLATION SECOND FIX

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

For this process the field operative must have full understanding of the G39/1 1992 engineering recommendation and be Authorised by the REC/DNO to remove the Cut-Out fuse carrier and connect to the outgoing side of the cutout. The second fix installation process is usually performed by the Siemens field service team. The process involves safety electrical testing, electrical connection to the supply and then basic functional testing. At the end of the second fix the sign should remain powered.

9.1

VISUAL INSPECTION
Check the following items before commencing with the testing: Check there is no water within either the Elektra sign enclosure or the feeder pillar. Earth connections are securely made and the earth wires are not damaged. Check the main assemblies are securely fitted and no fixings have become loose in transit. Check that there is no obvious damage to any cable insulation or any enclosure damage that may have happened during first fix installation.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

87 of 197 Released 20 January 2011 667/HB/33930/000

s
10 TESTING
IMPORTANT

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

No tests should be performed on the incoming side of the REC/DNO cut-out. Any operative who is to remove the cut-out fuse carrier or work in the vicinity of the cut-out, must have REC/DNO G39 Authorisation, be competent in relation to the sector scheme and the wear correct PPE. All testing equipment must be in good condition, be calibrated and have fused leads that conform to GS38.

10.1 INSULATION TEST


Equipment Insulation meter Standard field service tool kit

This test is to be carried out before any connection is made to the electricity supply. To perform an insulation test certain protection devices have to be removed. These protection devices are designed to intentionally conduct at high voltages, and this would cause a failure of the insulation test if they are not disconnected. There are two protection devices that have to be disconnected. Firstly the Gemini mains connection has to be disconnected. This is the 10 way mains connection feed to the Gemini on the comms panel. Secondly the master switch cover has to be removed and the earth wire disconnected from the MOV module on the DIN rail. See Figure 99.

Figure 99 MOVs (Metal Oxide Varistors) Ensure the switches within the isolator and sign enclosure are set as indicated by the following table. Switch/Fuse Master switch circuit breaker box Master switch 63A Master fuse 20A Heater fuse 10A Sign switch 32A MCB maintenance socket 6A Fuse Gemini 5A Fuse #1 10A Fuse #2 10A Fuse #2 10A Double Pole Isolator Master switch MCB (if fitted) State ON Intact Intact ON ON Intact Intact Intact Intact ON ON

Table 2- Insulation Test Switch State


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 88 of 197 Released 20 January 2011 667/HB/33930/000

s
Connect these line and neutral wires together. Take the insulation meter and switch it to the 500V range.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

In the feeder pillar there will be line and neutral wires that will not as yet be connected to the electricity suppliers fused cut-out. As a precaution, use a meter to check that these wires are not energised before touching them (check the meter on a known source first).

Place one meter probe on the connected line/neutral wires and the other on the primary earth stud. Measure the insulation resistance. It must be greater than 10 M. Record the measurement on the Elektra installation checklist form. At the end of the test return all the switches in the Double Pole isolator and master switch panel to the off position, replace/re-connect the protection devices and separate the line and neutral wires previously connected together.

10.2 POLARITY TEST


Equipment High voltage probes Multimeter Standard field service tool kit

The purpose of this test is to ensure that the line and neutral wires have been correctly connected by the electricity supplier and are not reversed. An REC/DNO authorised operative will need to connect the outgoing side of the cut-out to the line and neutral conductors in the feeder pillar. The Correct G39 PPE must be worn.

IMPORTANT

Under no circumstances should any work or testing be carried out on the incoming connections to the REC cut-out. Any tests must be performed downstream of the REC cut-out fuse.

Initially make sure all switches in the master switch assembly are off. Remove the electricity supply fuse carrier to ensure the circuitry is de-energised and wire the line and neutral wires to the outgoing side of the cut-out. Now set the switches and fuses as follows: Switch/Fuse Master switch crt breaker box Master switch 63A Master fuse 20A Heater fuse 10A Sign switch 32A MCB maint skt 6A Fuse Gemini 5A Fuse #1 10A Fuse #2 10A Fuse #2 10A DP Isolator Isolator switch Isolator MCB (if fitted) State OFF Intact Intact OFF OFF Intact Intact Intact Intact ON ON

Table 3 - Polarity Test Switch State


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 89 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Replace the electricity supply fuse carrier. Using a calibrated voltmeter/multimeter with leads conforming to GS38 measure the a.c. voltage between each of the pairs of points in the following table. Check the voltages are within the limits specified. If they are not a competent person needs to check the polarity at the feeder pillar. Checks may only be carried out on the outgoing side of the cut-out with the fuse carrier in place. No attempt should be made to change the connections to the incoming side of the cut-out.

Probe 1 Master switch input terminal Line Master switch input terminal Neutral Master switch input terminal Line

Probe 2 Elektra primary earth stud Elektra primary earth stud Master switch input terminal Neutral Table 4 - Polarity Test Limits

Voltage a.c. (V rms) 200 to 253 < 10 200 to 253

Record the measurement on the Elektra installation checklist form. At the end of the test return all the switches in the feeder pillar and master switch panel to the off position.

10.3 EARTH LOOP IMPEDANCE TEST


Equipment Earth loop impedance tester Standard field service tool kit

Earth loop impedance tests are carried out at points in the system where mains and exposed metal work are present. These are specified in Table 6 - Earth Loop Impedance Enclosure locations and values. The fault path within the installation comprises of the live conductors, control equipment and the Circuit Protective Conductor (CPC). The fault path external to the installation (Ze) contains the electricity supply authority's transformer windings, the live conductor and CPC of the electricity supply authority's distribution network, or the earth electrode.

The earth loop impedance test will include both elements described above. The earth loop impedance test results are required to ensure that in the event of an earth fault (or a short circuit fault) the protection devices e.g. fuses will disconnect within the time limit as specified in BS7671 (IEE Wiring Regulations). For fixed equipment such as the Elektra product, the specified disconnection time laid down by BS7671 is 5 seconds and for equipment connected via sockets the specified disconnection time is 0.4 seconds. This test is carried out after the Electricity supply has been installed. Ensure the switches within the feeder pillar and sign enclosure are set as indicated by the following table.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

90 of 197 Released 20 January 2011 667/HB/33930/000

s
Switch/Fuse Master switch crt breaker box Master switch 63A Master fuse 20A Heater fuse 10A Sign switch 32A MCB maint skt 6A Fuse Gemini 5A Fuse #1 10A Fuse #2 10A Fuse #2 10A Feeder Pillar Cut-out fuse Isolator switch Isolator MCB if fitted State ON Intact Intact ON ON Intact Intact Intact Intact Intact ON ON

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Table 5 - Earth Loop Impedance Test Switch State

10.3.1.1

Earth tests within the Elektra enclosure

Connect the L1 (red) probe of the earth loop impedance tester to the line input of the Master switch and the E earth test probe (black) to the points described in the following table, measure the impedance and record the measured value. L1 probe (red) Master switch input terminal Line Master switch input terminal Line Transformer or SMPS supply input terminal - Line Gemini Supply at Gemini connector Line Maintenance Socket MCB Output - Line E probe (black) Master Switch Assembly Cover Elektra sign primary earth stud Transformer frame or PSU enclosure close to its power input connector Comms panel metalwork Earth pin of the maintenance socket Maximum impedance () 1.84 Ohms 1.84 Ohms 5.93 Ohms

13.14 Ohms 3.00 Ohms

Table 6 - Earth Loop Impedance Enclosure locations and values The maximum impedance values are shown in the table. They are based on a 25A BS88 Cut-out fuse with a five second disconnect time. The values are obtained by taking the current that will blow the fuse within 5s (obtained from the IEE regulations) or disconnect the circuit breaker within 0.4s, and then using Ohms Law to find the required ELI. The result is multiplied by 0.8 to take account of possible ELI increases due to increases in temperature. If the Electricity Supply fuse is greater than 25A, the required ELI values must be obtained by a competent person from the IEE regulations, based on the cut-out fuse rating and type.

IMPORTANT

If the measurements exceed these values do not proceed with further testing and report the supply as out of specification to the customer.

Record the measurement on the Elektra installation checklist form (Appendix A - Installation Checklist)
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 91 of 197 Released 20 January 2011 667/HB/33930/000

s
10.4 MAINTENANCE SOCKET RCD TEST
Equipment o o RCD tester Standard field service tool kit

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Testing of an RCD is carried out in stages to establish correct operation. The first test is the no-trip test to check the RCD doesnt trip at low or nuisance current levels. The next test is to test the RCD at the rated tripping current and then finally a fast-trip test at five times the rated trip current of the RCD. These tests conform to the BS 7288 and BS 7671 standards. Apply the following test to the maintenance socket. 10.4.1.1 No-trip test Connect the RCD tester to the maintenance socket. Apply half the rated trip current (15 mA) at 0 and 180 degree phase angles. Confirm the RCD doesnt trip. 10.4.1.2 Rated trip current test Apply the rated trip current (30 mA) at 0 and 180 degree phase angles. Confirm the RCD trips in less than 200 ms.

10.4.1.3 Fast trip current test Apply five times the rated trip current (150 mA) at 0 and 180 degree phase angles. Confirm the RCD trips in less than 40 ms. Record the measurements on the Elektra installation checklist form (Appendix A - Installation Checklist)

10.5 COMPLETION OF INSTALLATION CHECKLIST


The installation checklist is provided in the appendix A of this document. At the conclusion of the installation Second Fix a completed copy of the installation checklist shall be provided to the Project Manager or Engineer. At the conclusion of the project this checklist will be given to the customer.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

92 of 197 Released 20 January 2011 667/HB/33930/000

s
11 COMMISSIONING
11.1 TURN THE SIGN ON
Carry out a visual inspection and risk assessment. Check that power is present at the sign.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Check that the Gemini watchdog enable link PL6 and the capacitor on link PL8 are in place. Remove the plastic from under the Gemini coin cell to activate the power down RAM support function. Turn on all the switches located in the Master Switch Panel after ensuring that the fuses are intact. Remove the battery fuse that is attached to the front of the Gemini with insulation tape. Insert it in the Battery fuse 5A fuse holder in the front of the Gemini unit. On the Elektra Master Switch Panel switch off the Gemini power switch. Confirm the Gemini unit still operates from battery power. Switch the Gemini back on.

11.2 POWER UP CHECK


Once powered observe the status indicators of the electronic modules within the Elektra sign. The sign will go through a power up process. The length of this process will depend on how many display modules are fitted to the sign. At the end of power-up check the following: Each Row Driver Board and Sensor Board within the sign has a unique address starting from [10] on the sensor module (See section 5.2.2.6) i.e. not showing [--]. No red fault LEDs are illuminated on any of the Row Driver (See section 0) and Sensor (See section 5.2.2.7) Boards. The fault LED on the Gemini RS232/422 Converter is not illuminated (See section 5.2.3.8) LEDs on Gemini are in accordance with following table (For more detail see section 5.2.3.4) Indicator System Comms Watchdog State Slow Flashing green Off Off

Figure 100 - Gemini LEDs on Start Up

11.3 DIAGNOSTIC WEB INTERFACE CONNECT


Connect to the Gemini using either the 25-way connector or Bluetooth. If this is the first time your PC has been used to connect to an Elektra sign in this way then it will be necessary to configure the serial and/or Bluetooth connections. These operations, and how to initiate a connection to the sign, are described in Appendices A and B of the GVP Reference Manual (667/HB/31760/000). A login screen similar to Figure 101 will appear when initially opening the sign's webpages.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 93 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 101 Web Browser User Name and Password

11.4 CHECKING SIGN CONFIGURATION


Enter the username and password: Username: Password:

Note

The username and password are distributed separately from this manual. Refer to Siemens Poole for details

If the username and password are correct the Siemens Outstation WEB interface window will appear as per Figure 102

Figure 102 - Outstation initial login Click on the |SignSetup| menu.


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 94 of 197 Released 20 January 2011 667/HB/33930/000

s
Check that under the <Refresh> button the following text is displayed: Status: Running

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

A table appears (as per Figure 103) that details the modules connected in the sign. Verify that the table agrees with the physical number of modules identified within the sign.

Note If any of the above stages do not occur as described, refer to Section 13.1

Figure 103 - Sign Configuration For information on the meaning of entries in the above web page refer to Section 13.1

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

95 of 197 Released 20 January 2011 667/HB/33930/000

s
11.5 SETTING THE LUMINANCE PARAMETERS

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

During normal sign operation, the brightness of the whole sign needs to be uniformly adjusted in response to the level of ambient illumination. If the ambient light decreases, the LEDs must also reduce in brightness. Conversely as the ambient light increases, the LEDs must get brighter. In order to measure the ambient illumination, the Sensor Board receives an input from a light sensor which is normally situated at the top of the sign. As the ambient light level measured by the Light Sensor changes, Gemini instructs the Row Drivers to change the brightness of the LEDs on the Display Boards accordingly. The method for changing the brightness of the LEDs is to rapidly switch them on and off at a rate that is not visible to the human eye. The ratio of the Off period to On period then allows control of the perceived brightness. This process is called Pulse Width Modulation (PWM) The Row Driver has 3 PWM outputs that are independently controlled. This allows 3 types (colours) of LED to be operated per row, each type having its own brightness/PWM relationships. As a result of this, the PWM for Red, Green and Yellow LEDs can be controlled independently, which is essential as they have different characteristics. ELEKTRA configurations include a single PWM setting for each of the illumination Bands. This is then modified by a certain percentage depending on the size of the displays and the colour of LEDs being driven. Select the Luminance Band Web Interface page (see Section 13.11.5) and ensure that the Luminance Band settings correspond to those defined in Figure 104.

UP Down Band Threshold Threshold 0 1 2 3 4 13 132 1320 7150 19800 11 108 1080 5850 162000

Display PWM 60 400 1000 3000 9999

Lantern PWM 60 400 1000 3000 9999

Figure 104 - Luminance Band Settings Select the Luminance Modifier Web Interface page (see Section 13.11.4) and ensure that the settings correspond to those in Figure 105 for the display type in the actual sign.

Board Type PWM Id Band 0 1 2 3 4

Y100 0 MOD 197 98 96 123 100

G100 R100 1 MOD 190 93 90 103 100 2 MOD 142 69 65 78 100

Y160 0 MOD 233 126 125 160 100

G160 R160 Y240 Y320 LANT 1 MOD 308 150 150 177 100 2 0 0 0 MOD 208 115 110 147 100 MOD MOD MOD 233 238 192 115 121 95 110 120 95 143 157 127 100 100 100

Figure 105 PWM Modifiers

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

96 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The MOD values for luminance band 0 and for the particular size of display being used should be entered into the fields in the screen shown in Figure 106. This should be repeated for the other luminance bands.

Figure 106 - Luminance Band Modifier entry

11.6 COLOUR SELECTION FOR RED / GREEN DISPLAY MODULES


Ignore this section for signs with Yellow displays. For signs with Red/Green displays the default colour for all text is Green. Reddening of special words is enabled and disabled using the Web Browser Special Words Compare Facility option on the StatusConfig->UVMS Library->General configuration page. Tick the Special Words Compare Facility box to enable this feature, as shown in Figure 107 Note that the performance of this feature can be modified using the Separate Special Words tick box, also shown in Figure 102 When not ticked, words are set to red even if they form part of a larger word e.g. *Full* would display as *Full* When ticked, words are only set to red if they are discreet, complete words with no adjoining characters e.g. Successfully would display as Successfully

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

97 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 107 - Enable Special Words Compare The special words themselves are defined on the StatusConfig->UVMS Library->Special Words configuration page, as shown inFigure 108. If no words are configured then no words will be red. It is important to check that these words correspond with the legends that the instation is using.

Figure 108 - Specify Special Words

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

98 of 197 Released 20 January 2011 667/HB/33930/000

s
11.7 HEATER TEST

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Click on the |StatusConfig| menu. On the left of the screen a vertical menu appears. Select Environmental Monitor/Heater.

Figure 109 - Heater Information Note the current settings. Change them to the following and click <Save>. Description Humidity on threshold Value 0

Verify that the heater relay LED illuminates and that the heater wire for each row is warm to the touch. Uncheck the checkbox Heater control supported. Confirm that the heater relay LED extinguishes. Return the Humidity on threshold value to its previous setting and ensure the Heater control supported checkbox is ticked.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

99 of 197 Released 20 January 2011 667/HB/33930/000

s
11.8 LIGHT SENSOR TEST

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Click on the |StatusConfig| menu. On the left of the screen a vertical menu appears. Select Environmental Monitor/Status.

Figure 110 - Sensor Status Confirm that the Current light level measurement value is a reasonable value for the prevailing conditions. Refer to the Table 7 for typical lux values. A light level that is significantly different to the table below can indicate an obscured or damaged light sensor. Conditions Night Street lighting Dark overcast day Average overcast day Full daylight (not direct sun) Direct sunlight Table 7 - Typical Lux Values Typical illuminance (lux) 05 5 40 1000 2000 2000 - 7000 10,000 20,000 30,000 130,000

11.9 DISPLAY TEST


Click on the |System| menu. Under the Applications heading you will see a list of all the applications that can be run on Elektra. Stop any applications that are running. Click the button <Start> next to the Tester application entry.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

100 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 111 -System Page with Tester Running When the Tester application is running a new menu entitled |Tester| appears in the header bar at the top of the web interface window. Click on the |Tester| menu.

Figure 112 - Tester page Check the loop checkboxes for the following tests: DisplayCheckTest LanternSequentialOnTest

Click on the <Run Test> button for both these tests. Confirm that the sign display performs as expected (full detail of tests may be found in Section 13.4 of this document)
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 101 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Whilst the tests are running, check fault table is clear and there are no unexpected faults in the System Log. At the end of the tests, remove the ticks from the loop tick boxes and WAIT FOR THE SIGN TO FINISH THE TEST SEQUENCE. Status will then be Not Running for each of the tests. Select the |System| menu and then click <Stop> next to the Tester application to stop it. Check fault table is clear and there are no unexpected faults in the System Log.

Figure 113 - Checking the Fault Table after running tests

11.10 CHECKING THE STATUS OF THE MC35 GPRS MODEM


Ensure that the SIM has been inserted and that the power is connected. The MC35 Diagnostic LED is used to indicate the following states. One the sign is communicating with the instation, the LED state should indicate there is data transfer. Operating State Immediately after power up Network Search or no SIM card inserted or no PIN entered or no GPRS network available Found GSM network - ready to connect Found GPRS network - ready to connect Data Transfer LED On for 2 seconds Flashes approx 2 seconds on 2 seconds off

Flashes once every 4 seconds Flashes twice every 4 seconds Flashes on for 1 second when data is transferred (this usually replaces the single flash every 4 seconds).

Figure 114 - MC35 LED Indications If it is initially not possible to achieve communications on the GPRS network, the RJ12 power connector should be disconnected and then re-inserted.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

102 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

11.11 MEASURING SIGNAL STRENGTH AT MC35 MODEM


If it is required to establish the siganal strength received by modem, the procedure here should be used. This procedure can be used for Radio Survey purposes as well as troubleshooting. This requires a terminal (Laptop with Hyperterminal or Techterm device) to be plugged directly into the MC35. The MC35 must be fitted with a valid SIM card for the relevant Service Provider. This procedure can be carried out at an installed Car Park or VMS Outstation or using the equipment shown below for a portable Radio Survey setup. (The battery used was a Yuasa NP7-12 charged up on VDO Outstation. This will run the MC35 for an extended period and is not too heavy to carry)
12V Battery (Yuasa NP7-12 or similar) +

Puck or stub Antenna as proposed to be used

654321

D.C.

Techterm or PC HyperTerminal

Siemens MC35 Terminal GPRS Unit

Figure 115 - MC35 Signal Strength Measurement Equipment 1) Configure the terminal for 9600-8-N-1 No flow control (use CTRL-SHIFT-F1 on Techterm for setup display) 2) Switch on MC35. Ensure that the PIN has been disabled (see previous section). Alternatively use CPIN=xxxx<cr> to enter PIN. 3) Wait for MC35 LED to flash briefly indicating that it has logged onto the network. 4) Enter AT+CSQ<cr>. Response will be +CSQ: x,y where x indicates the signal level : Value of x 0 1 2-30 31 99 Meaning -113dBm or less -111dBm or less -109dBm to -53dBm -51dBm or greater Not known or not detectable

A value of 12 or more is required. Less than this and calls may be dropped.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

IGT_IN

Page Status Date Document No.

103 of 197 Released 20 January 2011 667/HB/33930/000

s
11.12.1 Graphical Arrows

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

11.12 CONFIGURING SIGN FOR EXTERNAL CONTROL


ASCII strings are used to control which Graphical Arrow to display. Where Graphical Arrows are to be used it is necessary to ensure that the sign and the external control use consistent strings to represent the arrows. The strings recognised by the sign are configured using the web page described in section 13.11.6.

11.12.2

Elektra Control Modes

Elektra can be controlled in one of four ways: over a UTMC interface over a UVMS interface by parallel IO (UTC interface) by internal test functions A GVP application exists for each method of control. The application appropriate to the method of control required should be configured and then started. Only one control interface should be enabled at any time so only one application should be in the running state at any time. The configuration required depends on the application chosen. 11.12.2.1 Configuration of UTMC Application The UTMC Application is configured using the following: SNMP configuration web page see section 13.5.11 for description. The fields on this page should be set to match the configuration of the instation being used to control the sign. UTMC Application configuration web pages see section 13.10 for description. The Sign Setup pages (section 13.10.4) should be configured to match the sign and the remaining pages used to match the configuration of the instation. 11.12.2.2 Configuration of UVMS Application The UVMS Application is configured using the following: UVMS Application configuration web pages see section 13.12 for description. The fields on this page should be set to match the configuration of the instation being used to control the sign. 11.12.2.3 Configuration of IO Application The IO Application is configured using the following: Generic IO Application configuration web pages see section 13.8 for description The preset messages to be displayed also need to be configured. This is done in two parts: define the preset messages using the Preset Messages web page (one of the UVMS Library configuration web pages) described in section 13.11.8 define the rules which map the IO input patterns to the message required using the Message Rules web page described in section 13.8.4 11.12.2.4 Configuration of Tester Application The tests run by the Tester Application are configured using the following: Production Test configuration web pages see section 13.9 for description

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

104 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

11.12.2.5 Starting Applications Applications are started using the System web page. Applications are started and stopped using the buttons in the Control column. Note that only one Application should be running at any time.

Figure 116 - Running the Generic I/O application

11.13 SETTING A LEGEND FROM THE INSTATION.


If the signs are being controlled from a COMET or Siespace Instation, the sign can be manually set to display a particular legend as detailed below. This procedure may be carried out by the customer, Poole support team or the project Engineer. The Commissioning Engineer should remain on site to verify sign operation. The system allows an operator with sufficient permissions to override a sign, causing the system to ignore automatic application settings and remote systems settings. To override the legend displayed on a sign, select "Manual Settings -> Set Legend" from the sign context menu. The following window is then displayed:

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

105 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 117 - Setting the Sign from the To manually (force) the sign to a particular legend 1. Select the display element from the drop down list at the top of the window. (note: only the current selected element can be set at a time) 2. Select the 'Manually set to:' radio button. 3. Select the legend that you wish to force the sign to display. The list contains the legends that are available on this sign. 4. If you would like the override to expire automatically (and revert to automatic application or remote system settings), select the 'Automatically Cancel Setting at' checkbox and enter the time at which the override should be cancelled. This time defaults to 1 hour in the future. 5. Click on the 'OK' button to send the new setting to the sign. The Sign should then be observed to check that the Legend is displayed. The Gemini Fault table and the System Log should be checked for faults. The Instation should also be checked for faults associated with the sign. It is sensible to choose legends to exercise as much of the functionality of the sign as possible, including graphical arrows if fitted.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

106 of 197 Released 20 January 2011 667/HB/33930/000

s
12 MAINTENANCE
12.1 ROUTINE MAINTENANCE

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The maintenance scheme described by this manual is the manufacturers recommended maintenance routine to ensure that the Elektra product operates reliably throughout its operating lifetime.

12.2 CLEANING
Every PI (Periodic Inspection) should include the cleaning of the exterior of the sign. This should be completed with a sponge saturated with a pH neutral mild detergent solution. Do not use solvents to clean the sign surfaces Before washing inspect the sign for any failure of the seals or holes in the enclosure. If there are any do not continue until the sign has been repaired The surface is gently wiped and the sponge regularly squeezed and replenished to avoid any aggressive rubbing or the surface. If possible the sponge should be attached to a pole to avoid working at height.

12.3 YEARLY INTERVALS


Inform the Customer you will be carrying out work on the sign. Clean the exterior of the sign. In areas of high pollution or where grime accumulates on the surface of the sign the cleaning interval may have to be reviewed and cleaning more frequent. Check the enclosure is intact and the door locks are secure. Inspect the sign for any sign of traffic damage, pay particular attention to the support columns and mounting brackets. Inspect the enclosure and support columns for paint damage. Repair as necessary. Check for the interior of the sign for evidence of water ingress. Repair as necessary. Check the air filters in the rear doors are intact and permit the flow of air. Tighten any fixings as required. Inspect the wiring in the MDU (the operative must be G39 Authorised to do this) and the sign enclosure. Look particularly for insulation damage, overheating and check that the wires are terminated securely. Check the condition of the modules within the sign eg. PCBs, batteries, electrical assemblies, heaters. Look particularly for the following: damage scorching signs of overheating corrosion or deterioration secure mounting firm mating of connectors breakages missing parts (covers, screws etc) safety labelling is intact
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 107 of 197 Released 20 January 2011 667/HB/33930/000

s
Check the light sensor is operational (see 11.8). Check the heater is operational. Check the antenna is firmly attached and is intact.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Functionally test the sign to confirm that all LEDs can be correctly illuminated and extinguished (see 11.9). Repair as necessary.

Before using maintenance socket in either the sign enclosure or the MDU the RCD must be tested but pressing the button marked T or Test. Inspect the fault log. Note and rectify any faults reported. Perform a battery hold-up test. On the Elektra master switch panel switch off the Gemini power switch and confirm that the Gemini and its modem remain powered for a minimum of five minutes. If the unit loses support within five minutes the support battery must be replaced.

12.4 THREE YEARLY INTERVALS


At three yearly intervals both the yearly inspection should be carried out and also the electrical testing detailed in the installation section of this manual. The customer must be consulted before this takes place. This maintenance shall include the following tests: Insulation test (see 10.1). Polarity test (see 10.2). Earth loop impedance test Maintenance socket RCD test BS 7671 requries that the results of this inspection and test shall be recorded and passed on to the customer.

After the first inspection and test the competent person carrying out the inspection may recommend that the interval between future inspections be increased or decreased as a result of the findings of the inspection. Following the inspection the following wear-out items should be replaced. Replace the sign air filters. Where necessary the following maintenance can be applied to address particular problems but with normal operation this action shouldnt be required. Grease the door seal with silicone oil to prevent it from sticking. Oil the hinges and door stays as necessary.

12.5 DIAGNOSTICS AND FAULT FINDING


Wherever possible the repair engineer should use remote diagnostics to determine the fault with the Elektra sign. The Web interface provides many diagnostic abilities which will allow a fault to be identified before travelling to site. This will reduce the repair time and improve safety as the repair engineer will spend less time on site diagnosing the problem.

12.5.1

Fault Diagnosis

The full list of Elektra specific fault table codes can be found in section 12.5.2. This section gives some examples of how to determine the cause of some of the more likely faults.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

108 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

12.5.1.1 Gemini fault monitoring The Gemini software is responsible for monitoring its own fault status and that of the peripheral boards. This fault status information can be accessed from the web interface. The Gemini periodically (every 10 seconds by default) requests status information from each of the peripheral boards. The status replies from the peripheral boards include fault information. The Row driver boards are responsible for reporting faults associated with Display/Lantern boards and their associated power supplies. All faults are recorded in a system log on the non-volatile Gemini FLASH file system, and current fault status is maintained in a fault table. The system log contains a history of faults encountered while the fault table contains currently active faults. A list of Elektra specific fault table entries can be found in section 12.5.2. Only faults that require immediate action in order to prevent damage or to safeguard the user result in actions being taken by the boards themselves. In all other cases, the Gemini is the master arbiter, gathering all hardware faults status and issuing actions accordingly. The System log and fault table can be accessed using the web interface. This can be achieved using a laptop either remotely or locally. They can also be viewed with a handset using the WIZ command. 12.5.1.2 Display Board Pixel faults

Figure 118 - Fault Table showing Pixel Faults The information in the fault table shown above indicates that there is a single pixel fault on Row 0 (first row) board 4. It states that it is a Non Critical Pixel Fault. A critical pixel fault occurs when the number of pixels which have been requested to be illuminated but are faulty in any single displayed character is greater than or equal to the configured threshold. Pixels not requested to be illuminated have no effect on the determination of a critical pixel fault.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

109 of 197 Released 20 January 2011 667/HB/33930/000

s
1 Pixel Fault on this Board.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Viewed from the rear Figure 119 - Locating a Display Board Fault The System Log provides more detail. In the example shown inFigure 120, the Faulty Pixel is specified as being in Row 1 and at position 63,3. The 63 indicates that the fault is in the 63rd column, counting from zero at the extreme left hand end of the row when viewed from the front of the sign (or from the right hand side when viewed from the rear). The 3 indicates that the fault is in LED row 3, where row zero is always at the top of the board when viewed the right way up

The diagram shows how the position of the faulty pixel is identified. It is also specified as being Noncritical. Please note that Pixel Rows and Columns start at 0.

Figure 120 - System Log Showing Pixel Faults

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

110 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Viewed from the front (LED side of board) Figure 121 - Locating a Yellow Pixel Fault Figure 120 and Figure 121 above illustrate the example of when Yellow Displays are being used. A faulty Yellow Pixel is indicated by colour = 1 fault in the system log. This is the only colour code possible on a Yellow sign. The situation is slightly different on a Red/Green sign Figure 122 and Figure 123 both indicate a pixel fault at the same position (65,2), however colour =2 fault indicates a Red LED/Pixel. Colour = 4 fault indicates a Green LED/Pixel.

Figure 122 - Red Pixel Fault

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

111 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 123 - Green Pixel Fault

Figure 124 identifies the pair of LEDs described by Faulty Pixel in Display Row 0 at Position (65,2).

Viewed from the front (LED side of boards) Figure 124 Locating a Red/Green Pixel Fault

12.5.1.3 Sign Configuration Faults If there is a display module missing or a ribbon cable unplugged the sign will indicate that the actual sign does not match the stored configuration on the SignSetup web page as shown in Figure 125. By scrolling down the page the details of each board detected can be viewed and compared against what should be fitted. If the stored config is found to be correct and the sign does not match it, the sign should be repaired and then the "rescan" button used to initiate a rescan (this causes the configuration of the sign to be reassessed). If the sign is found to be correct, set to discovered config should be selected.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

112 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 125 - Actual Sign does not match Config The Fault Table and System Log shown below give the type of fault information that could be returned as a result of a faulty or disconnected light sensor.

Figure 126 - Light Sensor Fault

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

113 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 127 - Light Sensor Fault System Log information 12.5.1.4 Communications Failures If the Gemini is unable to communicate with the OSS, the following fault information may be displayed.

An internal Communications failure usually indicates that the Gemini cannot communicate with the rest of the sign. Figure 128 illustrates loss of communication with the peripheral with address 11 (gspi/comms/11/rxNoReply). This would probably be caused by the CAT5 lead between peripherals 10
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 114 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

and 11 being disconnected or faulty but could also be caused by peripheral 10 or 11 being faulty. In this case the UTMC application is running and it has also detected the fault (utmcvms/sign0/internalcomms). This is an example of a single fault leading to more than one fault being reported in the Fault Table.

Figure 128 - Communications Failure

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

115 of 197 Released 20 January 2011 667/HB/33930/000

s
12.5.2
12.5.2.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Elektra fault Codes


Description Power fail Cannot Establish Instation Connection No comms from instation Instation link verify timeout Further Information The application has been informed by the system that the power has failed It has not been possible for the application to connect successfully with the instation The connection with the instation has failed because no messages have been received within the configured timeout The connection with the instation has failed because a link verify message has not been received from the instation within the period it specified.

Generic IO Application Key Generic IO/powerFail uvmsIP/noInstationConnection uvmsIP/lossOfCommsToInstation uvmsIP/linkVerifyTimeout

12.5.2.2 UVMS Over IP Application Key uvmsIP/powerFail uvmsIP/noInstationConnection uvmsIP/lossOfCommsToInstation uvmsIP/linkVerifyTimeout

Description Power fail Cannot Establish Instation Connection No comms from instation Instation link verify timeout

Further Information The application has been informed by the system that the power has failed It has not been possible for the application to connect successfully with the instation The connection with the instation has failed because no messages have been received within the configured timeout The connection with the instation has failed because a link verify message has not been received from the instation within the period it specified.

12.5.2.3 UTMC Application Key utmcvms/sign/internalcomms utmcvms/sign/messagefailed utmcvms/sign/ledfail utmcvms/sign/ledfailcritical


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook

Description UTMCVMS: Internal Comms Fault UTMCVMS: Message failed UTMCVMS: LED Fail UTMCVMS: LED Fail Critical
Page Status Date Document No.

Further Information The application has been informed by the system that there has been a communications fault within the system The application has been informed by the system that it has not been possible to set the message it requested The application has been informed by the system that it has not been possible to set the message it requested The application has been informed by the system that there has been a critical LED failure
116 of 197 Released 20 January 2011 667/HB/33930/000

s
utmcvms/sign/heaterfail utmcvms/sign/watchdogreset utmcvms/sign/overtemp utmcvms/sign/luminancefail utmcvms/sign/lanternfail utmcvms/sign/powerfail UTMCVMS: Heater Fail UTMCVMS: Watchdog Reset UTMCVMS: Over Temperature UTMCVMS: Luminance Fail UTMCVMS: Lantern Fail UTMCVMS: Power Fail

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The application has been informed by the system that there has been a heater failure The application has been informed by the system that a watchdog reset has occurred The application has been informed by the system that an over temperature fault has occurred The application has been informed by the system that the sign luminance is not set correctly The application has been informed by the system that a lantern has failed The application has been informed by the system that the power has failed

12.5.2.4 Environment Library Key env/statusMonitorRegistration env/noTempSensor env/noHumSensor env/noLgtSensor env/gspiInterfaceFlt env/overTempFlt env/underTempFlt env/heaterControl/noTempSensor env/heaterControl/noHumSensor

Description Status monitor registration Fault No temperature sensor found No humidity sensor found No light sensor found GSPI Interface fault Over temperature alarm: nn Under temperature alarm: nn No temperature sensor found No humidity sensor found

Further Information The library has been unable to register with the GSPI library for status updates The library has been informed by the system that no temperature sensor has been found The library has been informed by the system that no humidity sensor has been found The library has been informed by the system that no light sensor has been found The library has been unable to connect to the GSPI library The library has detected that the temperature is greater than the maximum configured The library has detected that the temperature is less than the minimum configured The heater control has been informed by the system that no temperature sensor has been found The heater control has been informed by the system that no humidity sensor has been found

nn = measured temperature in deg C 12.5.2.5 UVMS Library Key

Description

Further Information

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

117 of 197 Released 20 January 2011 667/HB/33930/000

s
uvms/configNotBeingBackedUp uvms/rowrr/displayBoard uvms/gspiInterfaceFlt

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

uvms/gspiSignStartupFail

uvms/lanternllFault uvms/lanternAssemblyFault uvms/lanternFault/lluvms/lantern/pair uvms/lantern/single uvms/lantern/wrongNumber uvms/ledFailCritical uvms/ledFailNonCritical uvms/lossOfDownwardComms uvms/messageFail uvms/messageFormatFail uvms/controlThreadStartupFail uvms/signNotInRunningState uvms/noChangeInLightReading dd = display board id (first board = 0)
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook

Latest changes to GVP Config not backed up Config Size is nn Failed to compress configuration file Failed to export configuration file Row rr, Peripheral pp, Pixel Faults on Boards : dd (nn) GSPI Interface fault Unable to open gspiInterface Unable to get gspiInterface GSPI Sign Startup Sequence failure GSPI Sign Startup Sequence Failed (detecting lanterns) GSPI Sign Startup Sequence Failed (detecting sign size) Lantern ll has nn Faults Lantern assembly la has nn Faults Lantern Pair Fault str Single Lantern Fault str Wrong number of lanterns fitted Too many lanterns found: nn Critical Pixel Fault Non Critical Pixel Fault Loss of comms Failure to set requested message Invalid set message received UVMS Library Control Thread Startup Sequence Failure The sign is not in the running state - please see SignSetup No Change in Light Reading
Page Status Date Document No.

The backup of the configuration data to the sensor board has failed for the reason given

Display board dd on display row rr controlled by peripheral with address pp has nn pixel faults Failed to access the GSPI interface for the reason given

Initialisation of the sign failed for the reason given

Lantern ll has nn pixel faults The lantern assembly la has a total of nn pixel faults Pixel faults have exceeded the configured threshold on both lanterns on the pair identified by str Pixel faults have exceeded the configured threshold on the lanterns identified by str The wrong number of lanterns are fitted to the sign The number of pixel faults per character has exceeded the configured threshold for one or more characters within the message displayed on the sign There are pixel faults on the sign but not such that a critical pixel fault is caused GSPI communications has been lost It has not been possible to set the requested message The requested message is not valid The requested message is not valid The sign is not in the running state, further information can be found on the SignSetup? Web page No change in light reading has been detected within the configured period

118 of 197 Released 20 January 2011 667/HB/33930/000

s
la = lantern assembly id (first assembly = 0) ll = lantern id (first lantern = 0) nn = count pp = peripheral address rr = display row id (first row = 0) str = string containing further information regarding the fault GSPI Library 12.5.2.6 Key gspi/comms/aa/protocolIncompatible gspi/comms/aa/rxNoReply gspi/comms/aa/firmwareChecksum gspi/comms/aa/gspiAddressChanged gspi/comms/aa/configChecksum gspi/comms/aa/boardTypeChanged gspi/comms/aa//unrecognisedHardware gspi/comms/aa/boardTypeInvalid gspi/comms/aa/watchdog gspi/comms/aa/eepromAccess gspi/comms/aa/noGeminiComms gspi/comms/aa/lightSensorAccess gspi/comms/aa/temperatureOutOfRange gspi/comms/aa/humidityOutOfRange gspi/comms/aa/lightOutOfRange gspi/comms/aa/lightSensorScaleChange gspi/comms/aa/noDisplayBoardComms gspi/comms/aa/eepromAccess

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Description Protocol Incompatible No Response Received Firmware Checksum Failed GSPI Address Changed Configuration Checksum Failed Board Type Changed Unrecognised Hardware Invalid Board Type Watchdog EEPROM Access Failed No Comms from Gemini Light Sensor Access Failed Temperature Reading Out of Range Humidity Reading Out of Range Light Reading Out of Range Light Sensor Scale Change Failed No Display Board Comms EEPROM Access Fault : Board D(s) x y z
Page Status Date Document No.

Further Information The GSPI version supported by the sign is not compatible No response received from peripheral The peripheral has reported that its firmware checksum check has failed The peripheral has reported that its address has changed during operation The peripheral has reported that its configurationdata checksum has failed The peripheral has reported that its type has changed during operation The peripheral has reported that it does not recognise the hardware The peripheral has reported that the hardware is invalid The peripheral has reported that its watchdog timeout has expired The peripheral has reported that it failed to access its EEPROM correctly The peripheral has reported that it has blanked its row due to loss of communications with Gemini The sensor has reported that an access to the light sensor has failed The sensor has reported that a reading from the temperature sensor was out of range The sensor has reported that a reading from the humidity sensor was out of range The sensor has reported that a reading from the light sensor was out of range The sensor has reported that an attempt to change scale on the light sensor has failed The row driver has reported that there is a problem with the communications between display boards The row driver has reported that it has not been possible to access the EEPROM on one of the display boards

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

119 of 197 Released 20 January 2011 667/HB/33930/000

s
gspi/comms/aa/eepromChecksum gspi/comms/aa/eepromCompatibility gspi/comms/aa/eepromData gspi/comms/aa/displayBoardsIncompatibile

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

EEPROM Checksum Failed : Board ID(s) x y z EEPROM Compatibility Fault: Board ID(s) x y z EEPROM Data Out of Range : Board ID(s) x y z Incompatible Display Board

The row driver has reported that the checksum did not verify on data read from the EEPROM on a display board The row driver has reported that the data contained in the display board EEPROM is not compatible with its firmware Row driver has reported that the data read from a display board is invalid The row driver has reported that the display boards to which it is connected are not compatible with each other The row driver has reported that it has blanked its row due to an over temperature alarm from an LED driver device It has not been possible to open the GSPI interface

gspi/comms/aa/signBlankOverTemperature gspi/fwdl/gspiInterfaceFlt

Sign Blank due to Over Temperature GSPI Interface fault No gspiInterface specified Unable to open gspiInterface

aa = peripheral address x = display board id (first board = 0) y = display board id (first board = 0) z = display board id (first board = 0)

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

120 of 197 Released 20 January 2011 667/HB/33930/000

s
12.5.3 Visual Fault Indicators
Sympton VLED Power LEDs on Display boards not illuminating. Diagnosis 24V Supply absent. VLED PSU boards turned off by row drivers. This may be in response to: A lack of comms with Gemini or Display Boards LED Over Temperature Display Board Comms Fault Faulty VLED PSU board Faulty Display Board 24V Supply absent. VLED PSU boards turned off by ROW drivers. This may be in response to: A lack of comms with Gemini or Display Boards LED Over Temperature Display Board Comms Fault Faulty VLED PSU board Faulty Display Board Lantern boards not synchronized synchronization being attempted. Addressed but upstream comms subsequently lost. No Address allocated

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The Web interface can be used on site to view the Fault Table and System Log. The table given below indicates the possible diagnosis and action to be taken for other on-site symptoms. Action 24V Supply absent. Check CAT5 cable connections.

VLED Power LEDs on Lantern boards not illuminating.

Replace Board Replace Board 24V Supply absent. Check CAT5 cable connections.

VLED Power LEDs on Lantern boards Flashing COMMS LED on Row Driver or Sensor board not flashing Red FAULT LED on Row Driver or Sensor board flashing and 7-Segment display showing two dashes. Red FAULT LED on Row Driver or Sensor board permanently Illuminated Display not Dimming or incorrect brightness.

Replace Board Replace Board Check CAT6 cable connections and lantern ESD screws. Check CAT5 cable

Check CAT5 cable connections.

Faulty Row Driver/Sensor Board.

Replace board

PWM control of characters not taking place.

Gemini System LED (GREEN) not illuminating Gemini System LED (GREEN) permanently/steadily illuminated

No power or Processor error Processor error

Check the current light level using the browser and compare with typical luminance. Check power to Gemini. Change processor board. Hold down the Processor card Reset button for 2 seconds. Power Cycle Re-load Firmware Change processor board

Gemini System LED (GREEN) Heart Beat. Two flashes in 1 second, then

Main software not executing. Awaiting software update.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

121 of 197 Released 20 January 2011 667/HB/33930/000

s
off for 1 second. Fading up and down in brightness Main software not executing. Running launcher program and waiting local software update. Gemini Communications LED (GREEN) not illuminating.
Gemini Watchdog LED (RED) permanently illuminated.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

No data being received from the network.

Check Modem power and connections. Check state of Modem LED. Hold down the Processor card Reset button for 2 seconds. Power Cycle Re-load Firmware Change processor board

The hardware watchdog has timed out sometime in the past. When illuminated, this does not mean that the unit is currently in a watchdog state.

Instation indicates that enclosure door permanently open or permanently closed regardless of door position.

Door switch connections incorrect or circuit permanently open/short circuit.

Check door status using Browser. Check door switch connections to Gemini PL5.

Remove connections from PL5 and check resistance.

Heater not functioning.

Heater connections incorrect.

Gemini not turning on heater, possibly due to sensor board temp or humidity sensor or Gemini/Gemini Config. Conditions within the enclosure not requiring heater to be activated Figure 129 Visual Fault Indicators

Carry out Heater Test using Browser. Check Relay LED is on when heater should be on. Check Gemini PL5 output connections Carry out Heater test. Replace sensor board. Check Gemini Config Change Proc board No action

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

122 of 197 Released 20 January 2011 667/HB/33930/000

s
12.5.4
12.5.4.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Module replacement
Replacement: Light sensor

Light Sensor

Figure 130 - Replacing the Light Sensor In order to replace the Light Sensor it will be necessary to access the top of the sign. Ensure that the correct working at height risk assessments and method statements are used. Disconnect the light sensor lead from the sensor PCB. To test the replacement sensor plug it into the sensor board. Confirm correct operation of the new light sensor with it loosely held before continuing with the replacement. Remove the light sensor and antenna plate from the top of the sign. Unscrew the plastic light sensor nut from the light sensor housing and remove the faulty sensor. Feed the light sensor cable into the sign and replace the module into the plate. Reattach the plate. Note that the light sensor and its plate are areas where water can ingress into the sign. Ensure that the light sensor and its plate are securely fitted and all seals are intact. Feed the light sensor cable through to the sensor board and plug the sensor module into it. Confirm correct operation. 12.5.4.2 Replacement: Modem Antenna

In order to replace the Modem Antenna it will be necessary to access the top of the sign. Ensure that the correct working at height risk assessments and method statements are used. Remove the antenna cable from the modem on the comms panel and from any clips and cable ties. Remove the light sensor and antenna plate from the top of the sign. Unscrew the antenna and remove it. Feed the antenna cable into the sign and replace the module into the plate. Reattach the plate. Note that the antenna and its plate are areas where water can ingress into the sign. Ensure that they are both securely fitted and all seals are intact. Feed the antenna cable through to the modem and attach the connection. Confirm correct operation.

Antenna

Figure 131 - Replacing the Modem Antenna


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 123 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

12.5.4.3 Replacement: Sensor Module Note: copies of the sign configuration are held in the Gemini and sensor module. If both of these are changed at the same time then the configuration will be lost and have to be reloaded e.g. from OSS. To avoid the need to reload the configuration it is recommended that the procedure for replacing one of these items is completed before starting replacement of the other (order does not matter). Ensure that the sign power is turned off at the Master Switch Assembly. Remove the light sensor connection, the power connection and the RJ45 leads. Remove the screw securing the board to the ESD metal standoff. Carefully ease the board from the plastic standoffs. Fit the new board, remembering to fit the ESD screw and the connectors that were removed. Plastic Standoff Power Connection Plastic Standoff

Light Sensor Connector

ESD Screw

RJ45 Connectors Figure 132 - Replacing the Sensor Module

Plastic Standoff

Replacing the sensor module will lose its copy of the sign configuration. On restart the sign detects and reports this situation on the Sign Setup web page. The action to return the sign to the running state depends on the state reported (which in turn depends on the state of the new sensor module e.g. if it is brand new or previously used in another sign): Message: Stored config and backup config don't match - press Save Config to Backup button Message: No backup config exists - press Save Config to Backup button

The action performed may result in further messages being displayed depending on the state of the sign and the action performed. See section 13.1 for further information on the Sign Setup web page and section 13.1.1 for details on sign states and appropriate action.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

124 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

12.5.4.4 Replacement: Row Driver Module Ensure that the sign power is turned off at the Master Switch Assembly. Remove power connection (if fitted) and the RJ45 leads. Remove the screw securing the board to the ESD metal standoff. Carefully ease the board from the plastic standoffs and the connector at the rear, without twisting the board. Fit the new board ensuring that the rear connector is correctly seated and that the board is flat after it has been pressed onto the standoffs. Fit the new board, remembering to fit the ESD screw and the connectors that were removed. Plastic Standoff Plastic Standoff

ESD Screw

Plastic Standoff

RJ45 Connectors Figure 133 - Replacing the Row Driver Module

12.5.4.5 Replacement: VLED PSU Ensure that the sign power is turned off at the Master Switch Assembly. Remove the 24V power connection. Remove the screw securing the board to the ESD metal standoff. Carefully ease the board from the plastic standoffs and the connector at the rear, without twisting the board. Fit the new board, remembering to align the connector correctly. Replace the ESD screw and the power connector. Plastic Power Connector Standoff Plastic Standoff

ESD Screw Figure 134 - Replacing VLED PSU

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

125 of 197 Released 20 January 2011 667/HB/33930/000

s
12.5.4.6 Replacement: Display module

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Note that, with the exception of the Lanterns, the sunshields should NOT be removed from the sign. To replace a display module it must be removed from the sunshield as described here. Ensure that the sign power is turned off at the Master Switch Assembly. Remove the Row Driver, Sensor module and VLED PSU from the rear of the display module if they are present. Then remove the ribbon cables. Unscrew the two ESD screws. Remove the board by easing it from the standoffs without twisting it. To install the new board, locate it on the standoffs and then fit the ESD screws. Replace any other boards that were originally fitted (Row Driver, Sensor or VLED PSU taking care to replace them in the same positions. Finally, reconnect the ribbon cables. A 240 mm display is shown here, however the procedure is essentially the same for the other types of display (not lanterns). ESD Screw

Standoffs

Standoffs

ESD Screw Figure 135 - Replacing Display Modules

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

126 of 197 Released 20 January 2011 667/HB/33930/000

s
12.5.4.7 Replacement: Lantern module

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Note: Unlike other display modules, lanterns are removed complete with their sunshield. Do not replace unless you have a spare. Ensure that the sign power is turned off at the Master Switch Assembly. Remove the RJ45 leads, the VLED cables and the 24V power cables (if present). Partially undo the two nuts that hold the lantern to the sign and then slide the lantern until the large washers line up with the enlarged part of the holes in the metalwork. It should then be possible, with care, to withdraw the lantern module. Once the Lantern module has been removed from the sign, change the Lantern PCB in the same manner described in Section 12.5.4.6 above. When replacing the lantern module into the sign it should be orientated with the VLED connection towards the bottom of the sign and fitted so that the enlarged parts of the holes in the metalwork fit over the large washers. The lantern should then be slid downwards and the nuts tightened.

Re-fit lantern and then slide down

Figure 136 - Replacing the Lanterns 12.5.4.8 Replacement: Gemini Note: copies of the sign configuration are held in the Gemini and sensor module. If both of these are changed at the same time then the configuration will be lost and have to be reloaded e.g. from OSS. To avoid the need to reload the configuration it is recommended that the procedure for replacing one of these items is completed before starting replacement of the other (order does not matter). Disconnect the power from the Gemini using the switch in the Master Switch Assembly. Remove the RJ45 lead from the RS232 to RS422 converter board. Then remove the PL1 connector from the Gemini power supply and remove the earth connection block using a screwdriver. Remove the PL5 connector from the Gemini processor board. Disconnect the Modem ribbon cable from the Gemini processor board. Support the Gemini Unit and unscrew the four screws holding it to the comms module. Remove the Gemini Unit. The Gemini can be placed in a bag and lowered safely to the ground using a lanyard. Screw the replacement Gemini to the comms module. Fit the RJ45 connector, PL1 connector, earth connector, PL5 connector and Modem Ribbon cable. Replacing the Gemini will lose its copy of the sign configuration. On restart the sign detects and reports this situation on the Sign Setup web page. The action to return the sign to the running state depends on the state reported (which in turn depends on the state of the new Gemini e.g. if it is brand new or previously used in another sign): Message: Actual sign does not match stored config press Set to Discovered Config button Message: Stored config and backup config don't match press Load Backup Config button Message: No stored config exists press Load Backup Config button
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 127 of 197 Released 20 January 2011 667/HB/33930/000

Security classification Version Last Editor Document Name

s
Screw securing earth terminal block.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The action performed may result in further messages being displayed depending on the state of the sign and the action performed. See section 13.1 for further information on the Sign Setup web page and section 13.1.1 for details on sign states and appropriate action.

PL1

Figure 137 - Replacing the Gemini

Earth terminal block, removed.

12.5.4.9 Replacement: Modem Disconnect the power from the Gemini using the switch in the Master Switch Assembly. Remove the RJ12, 9 pin D and antenna connectors. Unscrew the 2 screws that hold the modem to the comms panel. Remove the modem. Remove the SIM card and fit it to the replacement unit. Screw the replacement modem to the comms module. Fit the RJ12, 9 pin D and antenna connectors. Reconnect the power to the Gemini unit. 12.5.4.10 Removal: Comms module If the comms panel is preventing access to other modules, first try slackening the four nuts identified in Figure 138 and sliding the module sideways. If it is necessary to remove the module, first disconnect the power to the sign using the master switch. Remove the RJ45 lead from the RS232 to RS422 converter board. Remove the antenna/telephone connection from the modem. Remove the PL1 connector from the Gemini power supply and then remove the earth connection block using a screwdriver. Remove the PL5 connector from the Gemini processor board. Before removing the four bolts that secure the Comms module to the sign frame, it may be necessary to support the comms module in some way e.g. a bungee rope. If work is being carried out at height a lanyard should be attached to allow the module to be lowered while maintaining three points of contact. The earth wire can be removed from the earth connection block and the block replaced on the Gemini unit.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

128 of 197 Released 20 January 2011 667/HB/33930/000

s
Nuts securing comms module. PL1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Screw securing earth terminal block.

PL5 Figure 138 - Replacing the Comms Module

Earth terminal block, removed.

Remove the four nuts and washers that secure the comms module to the sign frame. Remove the comms module and lower it to the ground. To install a new comms module, raise it to the sign using a safe method, locate the four bolts and fit the nuts and washers. Fit PL1 and connect the earth wire. Connect the antenna/telephone connection from the modem and reconnect the RJ45 lead.

IMPORTANT

Ensure that the four mounting nuts on the Comms panel are fully tightened at the end of any work on the panel.

12.5.4.11 Replacement; Transformer The Transformers are very heavy and great care must be exercised when they are replaced. - Ensure that pedestrians are not endangered at any time. The power should be disconnected using the master switch. The tie wraps holding the cables to the transformer which is to be replaced should be carefully cut. The mains input connections should be removed and screwed into a spare connection block to make them safe. The output connections from the fuse holders and connection blocks should be labelled and then removed. The Transformer Mounting Plate should be unbolted from the sign and a lanyard attached to the lifting hole. The Transformer complete with Mounting Plate should then be lowered to the ground.

If the replacement Transformer is not complete with Mounting Plate, the Plate must be transferred from the faulty Transformer. The lanyard can then be used to hoist the Replacement Transformer up to the sign enclosure (after appropriate safety precautions have been taken). The Transformer Mounting Plate should be bolted into the sign and the output cables reconnected. The Mains cables should then be reconnected and replacement tie wraps fitted.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 129 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 139 - Replacing Transformers 12.5.4.12 Replacement; SMPS The PSUs are heavy and great care must be exercised when they are replaced - Ensure that pedestrians are not endangered at any time. The power should be disconnected using the master switch. The tie wraps holding the cables to the PSU which is to be replaced should be carefully cut. The mains input connections should be removed and screwed into a spare connection block to make them safe. The negative output connections from the PSU and the positive connections from the fuse holders should be labelled and then removed. The PSU Mounting Plate should be unbolted from the sign and a lanyard attached to the lifting hole. The PSU complete with Mounting Plate should then be lowered to the ground. If the replacement PSU is not complete with Mounting Plate, the Plate must be transferred from the faulty PSU. The lanyard can then be used to hoist the Replacement PSU up to the sign enclosure (after appropriate safety precautions have been taken). The PSU Mounting Plate should be bolted into the sign and the output cables reconnected. The Mains cables should be reconnected and replacement tie wraps fitted.

Figure 140 - Replacing SMPS

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

130 of 197 Released 20 January 2011 667/HB/33930/000

s
13 ELEKTRA SPECIFIC STATUS AND CONFIGURATION WEB PAGES
13.1 SIGN SETUP

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

The Sign Setup web page allows the status and hardware configuration of the sign to be reviewed and some aspects of its operation to be configured. The contents of this web page depend on the status and hardware make up of the sign.

13.1.1

Status

When opened, the sign setup web page (if possible) shows a table identifying the boards found in the sign and the status of the sign. For example: Figure 141 shows an example of a sign operating correctly (indicated by the status Running) Figure 142 shows an example of a sign where the boards have been detected but a configuration problem has been detected (indicated by the status Actual sign does not match stored config) Figure 143 shows an example of a sign where it has not been possible to detect any boards

Figure 141 - Sign Configuration (Running)

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

131 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 142 - Sign Configuration (Sign doesn't match config)

Figure 143 - Sign Configuration (Attempting to access GSPI)

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

132 of 197 Released 20 January 2011 667/HB/33930/000

s
Message Working Releasing GSPI Cause An operation is in progress An operation requires exclusive use of the sign e.g. peripheral firmware update The Gemini is attempting to access the boards within the sign The sign is being interrogated to determine boards present

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Table 8 lists the status messages which might be displayed. The action performed may result in further messages being displayed depending on the state of the sign and the action performed. Action Wait until operation completes Wait until operation completes

Attempting to access GSPI

Scanning GSPI

Actual sign does not match stored config

The configuration of boards within the sign has been changed The Gemini has been changed

Faulty comms between boards within the sign Stored config and backup config don't match The stored config has been updated e.g. through use of Set to Discovered Config button. The sensor board has been changed The Gemini has been changed One of the configs has become corrupt.

Wait for status to change. If this state persists for too long then investigate the wiring between the Gemini and Sensor board. Wait until table of boards appears. If this state persists for too long then investigate the wiring between the Gemini and Sensor board. Verify that the configuration displayed is as expected. If it is then press Set to Discovered Config button. If it is not then proceed as for faulty comms. Verify that the configuration displayed is as expected. If it is then press Set to Discovered Config button. If it is not then proceed as for faulty comms. Investigate for faulty cabling between boards or a faulty board. Press Rescan button when fault rectified. Press Save Config To Backup button.

Press Save Config To Backup button. Press Load Backup Config button or load config using ConfigImportExport web page. Verify that the configuration displayed is as expected. If it is then press Save Config To Backup button. If it is not then press Load Backup Config button. Press Save Config To Backup button. Press Clear Backup Config button Press Load Backup Config button or load config using ConfigImportExport web page Verify that the configuration displayed is as expected. If it is then press Set to Discovered Config button. If it is not then proceed as for faulty comms. None

No backup config exists No stored config exists

The sensor board has been changed Initial setup of new sign The Gemini has been changed Initial setup of new sign

Neither stored nor backup configs exist

Running

Sign is operating correctly Table 8 - Sign Statuses

Depending on the state of the sign, one or more of the following buttons may be available:

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

133 of 197 Released 20 January 2011 667/HB/33930/000

s
Button Refresh Rescan Set To Discovered Config Load Backup Config Save Config To Backup Clear Backup Config

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Function Refreshes the web page Rescans the sign to determine what boards are present Stores the config discovered from the sign into the Gemini Loads the backup config stored on the sensor board into the Gemini Saves the config stored within the Gemini to the sensor board Erases the backup config stored on the sensor board Table 9 - Sign Configuration - available buttons

13.1.2

Hardware Configuration

Whenever possible the Sign Setup webpage lists the peripheral hardware connected to the Gemini to form the sign e.g.Figure 141, Figure 142Figure 142. Each row of the table represents a connected peripheral and each column gives information about the peripherals: Address this is the address of the peripheral as displayed on its seven segment display and reported in the fault table and system log Type this is the type of the peripheral: o Sensor a sensor board peripheral o Display a row-driver peripheral connected to alpha numeric display panels o Arrow a row-driver peripheral connected to a graphical arrow display panel o Lantern a row-driver connected to lantern panels Details this gives further details of the peripheral found: o Part number o Firmware version number o Hardware type: 2 = row-driver 4 = sensor o Hardware version number o Compatibility number Function Details details of the functions supported by the peripheral. o For a sensor this is a list of the sensor supported o For a row-driver this is details of the display panels connected: Type: 1 = message 2 = lantern Character type: full matrix or individual character Compatibility Size in mm e.g. 100, 160 Number of pixel columns Number of pixels in each column Version of configuration data supported Version of configuration data fitted Format of configuration data supported Format of configuration data fitted Pixel colour(s)

13.1.3

Configuration of Graphical Arrows and 320mm Operation

The following aspects of the operation of the sign are configured through the sign setup web page. 13.1.3.1 Graphical arrows A display / arrow option is given in the 2nd column for each row in the sign which can be used as a graphical arrow. The correct option should be selected to match the sign.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

134 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 144 - Arrow Selection

13.1.3.2 320mm operation This option is displayed on the SignSetup screen if it is possible to use the sign to display 320mm characters. Select this mode of operation if the sign is to be used in this way. The following screen shot shows the tick box used to select 320mm characters (double height/width).

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

135 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 145 - Configuration of Double Height / Width Operation The following screen shot shows the screen once double height characters have been selected and the application is running.

Figure 146 - Verification of Double Height / Width Operation

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

136 of 197 Released 20 January 2011 667/HB/33930/000

s
13.2 PERIPHERAL FIRMWARE UPDATE

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 147 - Peripheral Firmware Update This page allows the firmware within the peripheral devices connected to the Gemini (the sensor and row-drivers) to be updated. This operation should only be performed if the sign is in the running state, in which case a screen such as that in Figure 147 will be displayed. The location of the peripheral firmware file on the Gemini filesystem is displayed along with the version of that firmware, in this example: etc/peripheralFW.hex version 1.0 Note the warning messages on the screen these should be followed to ensure best performance. An update is only required if one or more of the peripheral devices contains firmware of a lower version to that listed on this page. The versions of the firmware current contained by the peripherals can be found using the SignSetup web page as described in section 13.1. If required, click on the Start button to initiate the update process. The screen will change to give an indication of progress then return to that shown in Figure 147 when the operation is complete. If it has not been possible to detect the peripheral cards then the screen shown in Figure 148 is displayed. The cause of this problem should be investigated further by viewing the sign status as described in section 13.1.

Figure 148 - Peripheral Firmware Update, No Peripherals Detected

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

137 of 197 Released 20 January 2011 667/HB/33930/000

s
13.3 SYSTEM

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

This screen displays the list of software components running on the outstation. Applications can be started and stopped and the outstation can be re-booted. Please see the GVP Reference Manual (667/HB/31760/000) for detailed information relating to this screen. Screen shots included here merely show the Elektra contents of these pages.

Figure 149 - System (Part 1)

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

138 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 150 - System (Part 2)

13.4 TESTER
The tester application can be used to run various tests which can be seen in the screenshot below. Tests are started by clicking the run test button. If it is required that the test runs in a constant loop, the loop box should be ticked.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

139 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 151 - Tester The operations performed by each test are as follows: LogSensorReadingsTest: Periodically writes the values obtained from the fitted sensors to the System Log. This test can be used to verify that the sensors are operating. LanternSequenceOnTest: Illuminates each lantern in turn in the order specified on the Lantern Position configuration screen (section 13.11.3). This test can be used to verify that the lantern cabling and position configuration are as expected. LanternBrightnessTest: Cycles the brightness of the lanterns between maximum and zero brightness. This test can be used to verify that PWM brightness control of the lanterns is working correctly. DisplayAllOnTest: Turns on all of each colour display pixels (not lanterns) in turn. This test can be used to verify that pixels can be turned on. DisplayCheckTest: Displays a checkerboard pattern and its inverse for each colour in turn. DisplayHorizontalTest: Displays horizontal lines for each colour in turn. DisplayVerticalTest: Displays vertical lines for each colour in turn. FrequentPixelUpdateTest: Displays animated spinners. This test produces a significant load on the internal communications and so can be used to test for problems in this area. HorizScrollTest: Displays a horizontally scrolling bar. This test produces a significant load on the internal communications and so can be used to test for problems in this area. DisplayGraphicalArrowTest: Cycles through the eight graphical arrow images. DisplayPresetMessageTest: Displays the preset message defined by the configuration (section 13.9.6) DisplayAllPresetMessagesTest: Cycles through all defined preset messages until an empty message is found. This test can be used to verify the display of configured preset messages. IdentifyRowsTest: Displays the row number of each row on the row itself. This can be used to verify row connection and identity. LuminanceBandTest: Displays a preset message as per DisplayPresetMessageTest but forces the sign brightness to the band specified. LuminanceOverrideTest: Displays a preset message as per DisplayPresetMessageTest but forces the sign brightness to the PWM level specified. Various characteristics of the tests can be configured as described in section 13.9.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 140 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.5 STATUSCONFIG COMMON WEB INTERFACE SCREENS


This section describes the common StatusConfig web interface screens provided by the GVP platform. Wherever possible reference is made to the GVP Reference Manual (667/HB/31760/000) but where information is not yet available in that document, it is contained here. It is envisaged that future issues of the GVP Reference Manual will contain this information and allow it to be removed and referenced from this section.

13.5.1

SITE LOG SCREEN

Refer to Section on Site Log Screen in GVP Reference Manual 667/HB/31760/000

13.5.2

SYSTEM LOG SCREEN

Refer to Section on System Log Screen in GVP Reference Manual 667/HB/31760/000

13.5.3

GPRS Screen

Figure 152 - GPRS Enable PPP interface Enable or Disable the PPP (point-to-point) IP interface on the RS232 modem serial port.

PPP Chat Script Name Configure the name of the chat script used to configure the modem before PPP is started. Possible values are gprs, nullmodem, winserver Baud Rate This option defines the RS232 BAUD rate that will be used beteen the serial port and the Modem. Possible values are 9600, 19200, 38400, 57600, 115200 PPP Start delay Configure the delay (in seconds) between modem power on and PPP starting. This is used to give the GPRS/other modem chance to connect upstream.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 141 of 197 Released 20 January 2011 667/HB/33930/000

s
Modem Power Delay Configure the delay (in seconds) to keep the modem power off.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Refuse PAP With this option, pppd will not agree to authenticate itself to the peer using PAP. Refuse CHAP With this option, pppd will not agree to authenticate itself to the peer using CHAP. Username Username to use for authentication. Password Configure the password used if PAP or CHAP authentication is required Make Default Route With this option, pppd will make the PPP interface the default IP route for IP traffic. GPRS APN Define the APN if using the GPRS connection script. Site Name Configure the site name for this Gemini unit. OSS Address Configure the IP address for the Outstation Support Server Enable OSS interface Enable or Disable the Outstation Support Server interface. Enable OSS backup Enable or Disable the backup of config to the Outstation Support Server.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

142 of 197 Released 20 January 2011 667/HB/33930/000

s
13.5.4 Basic Status Screen

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 153 - Basic Status Free RAM The amount of free RAM memory in bytes Total RAM The amount of RAM memory in Bytes Free Disk Blocks The amount of free Disk blocks Total Disk Blocks The total amount of Disk blocks CPU load The percentage of CPU used.

13.5.5

Ethernet Screen

Figure 154 - Ethernet


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 143 of 197 Released 20 January 2011 667/HB/33930/000

s
Ethernet IP Mode Configure how the IP address is set for the ethernet connector Ethernet IP Address Configure how the IP address is set for the ethernet connector Ethernet IP Netmask Configure the netmask that should be used for the Ethenet network.

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Ethernet IP Broadcast Configure the broadcast address that should be used for the Ethenet network. Ethernet IP Default Route (Not Set) Configure the Ethernet Interface to be the Default Route for IP data. Ethernet IP Gateway Configure the gateway address that should be used for the Ethenet network.

13.5.6

DNS Screen

Figure 155 - DNS DNS Nameserver Description: Configure the address for the DNS nameserver. Default: 0.0.0.0 DNS Domainname Description: Configure the domain name for the DNS. Default: gemini.net

13.5.7

DDNS Screen

Figure 156 - DDNS

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

144 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Enable DNS update Description: Enable or Disable the Dynamic Domain Name Server update system. This is used to allow the instation to find the outstation when using a dynamic IP address. Default: false Reverse ZONE size Description: Define the size of the reverse DNS zone size. This must match the zone defined at the DNS server. For example, for the reverse zone 100.16.172.in-addr.arpa, a value of 3 is needed, for 172.in-addr.arpa a value of 1 is needed. Default: 2

13.5.8

OSS Screen

Figure 157 - OSS Interface Enable OSS Description: Enable or Disable the OSS Interface. Default: false Enable Config Backup Description: Enable or Disable the automatic backup of config to the OSS. Default: false OSS Address. Description: Configure the IP address for the Outstation Support Server. Default: 10.10.10.10 TFTP Port number. Description: Define the port number of the OSS file transfer. Default: 69 Config Backup Interval. Description: Number of minutes between backups to OSS. Default: 60 Initial Config Backup Interval. Description: Number of initial minutes before performing the first backup to OSS. Default: 1

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

145 of 197 Released 20 January 2011 667/HB/33930/000

s
13.5.9 PPP Screen

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 158 -PPP Enable PPP interface Description: Enable or Disable the PPP (point-to-point) IP interface on the RS232 modem serial port. Default: false PPP Chat Script Name Description: Configure the name of the chat script used to configure the modem before PPP is started. Possible values are gprs, nullmodem, winserver. Default: gprs. Baud Rate Description: This option defines the RS232 BAUD rate that will be used beteen the serial port and the Modem. Possible values are 9600, 19200, 38400, 57600, 115200. Default: 19200. PPP Start delay Description: Configure the delay (in seconds) between modem power on and PPP starting. This is used to give the GPRS/other modem chance to connect upstream. Default: 30. Modem Power Delay Description: Configure the delay (in seconds) to keep the modem power off. Default: 10. Carrier Detect Timeout Description: Configure the delay (in seconds) to wait before giving up on Carrier Detect and restarting. This option is only used if the Use Carrier Detect option is enabled. Default: 60. Use Carrier Detect Description: With this option, pppd will wait for the carrier detect to be active before starting PPP. Default: false

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

146 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Refuse PAP Description: With this option, pppd will not agree to authenticate itself to the peer using PAP. Default: false. Refuse CHAP Description: With this option, pppd will not agree to authenticate itself to the peer using CHAP. Default: false Ask for UPAP Description: Ask the peer to authenticate itself using PAP [Password Authentication Protocol] authentication. Default: false. Ask for CHAP Description: Ask the peer to authenticate itself using CHAP [Challenge Handshake Authentication Protocol] authentication. Default: false. Require Authentication Description: With this option, pppd will not bring the PPP link up unless the peer authenticates itself. Default: false. Username Description: Username to use for authentication. Default:. Password Description: Configure the password used if PAP or CHAP authentication is required. Default: Make Default Route Description: With this option, pppd will make the PPP interface the default IP route for IP traffic. Default: true Local IP Address Description: Configure the IP address of the modem PPP interface. If the IP address is set to 0.0.0.0, then the peer will be expected to provide a valid IP address. Default: 0.0.0.0 Remote IP Address Description: Configure the IP address of the remote peer. The remote address will be obtained from the peer if not specified in any option (by settings to 0.0.0.0. Thus, in simple cases, this option is not required. Default: 0.0.0.0 PPP Interface Netmask Description: Configure the netmask address for the PPP interface. If the IP address is set to 0.0.0.0, then the peer will be expected to provide a vaild IP address. Default: 0.0.0.0 Idle Time Limit Description: Configure the delay (in seconds) to keep PPP active without traffic. If no IP traffic is received for this length of time, the PPP link is dropped. Setting to 0 will disable. Default: 0 LCP Echo Failures Description: pppd will presume the peer to be dead if n LCP echo-requests are sent without receiving a valid LCP echo-reply. If this happens, pppd will terminate the connection. Use of this option requires a
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 147 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

non-zero value for the LCP Echo Interval parameter. This option can be used to enable pppd to terminate after the physical connection has been broken (e.g., the modem has hung up). Default: 10 LCP Echo Interval Description: pppd will send an LCP echo-request frame to the peer every n seconds. Normally the peer should respond to the echo-request by sending an echo-reply. This option can be used with the LCP Echo Failures option to detect that the peer is no longer connected. Default: 10 Disable Van Jacobson Compression Description: Disable Van Jacobson style TCP/IP header compression in both the transmit and the receive direction. Default: true Max Connection Time Description: Terminate the connection when it has been available for network traffic for n seconds (i.e. n seconds after the first network control protocol comes up). 0 to disable. Default: 0 GPRS APN Description: Define the APN if using the GPRS connection script. Default: apn.org.uk

13.5.10

TFTP Screen

Figure 159 - TFTP Default TFTP Server Description: Configure the IP address to be used by default when perform TFTP actions. Default: 10.0.0.20 TFTP Server Port Description: Configure the IP port to use on the TFTP server. Default: 69 Lower TFTP Client Port Description: Configure the lower local IP port to use. Default: 20000 Upper TFTP Client Port Description: Configure the upper local IP port to use. Default: 30000

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

148 of 197 Released 20 January 2011 667/HB/33930/000

s
13.5.11 SNMP Screen

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

TFTP Client Timeout Description: Configure the number of seconds before a TFTP download/upload timeout. Default: 8

Figure 160 - SNMP Authentication Type Description: Configure Authentication Type Used. Default: none Trap Type Description: Configure Trap Type Used. Default: v1Trap SNMP Community Description: Configure the community string used for SNMP V1 and V2c. Default: public

Trap Peer Address Description: Configure the IP address that SNMP TRAPs and INFORMS are sent to. Default: 10.0.0.10 Trap Peer Port Description: Configure the IP port that SNMP TRAPs and INFORMS are sent to on the peer. Default: 162 Agent Port Description: Configure the IP port that the local SNMP agent will use for incomming SNMP get and set requests. Default: 161 Username Description: Configure the username required for SNMP v3 authentication. Default:

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

149 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Password Description: Configure the password required for SNMP v3 authentication. NOTE this needs to be a minimum of size of 8. Default: System Location Description: Configure the System location field presented via the SNMP system MIB. Default: unknown System Contact Description: Configure the System contact field presented via the SNMP system MIB. Default: unknown Enable Verbose Logging Description: Configure the SNMP agent to produce more Verbose debug logs. Default: false Force Trap warnings Description: Configure the SNMP agent to report trap sending errors as warning, this reduces the amount of messages in the system log when it is expected to get problems sending traps. Default: false

13.5.12

Services Screen

Figure 161 - Services Enable TFTP Server Description: Enable or Disable the TFTP server in the outstation. Default: false

13.5.13

Telnet Server Screen

Figure 162 - Telnet Server

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

150 of 197 Released 20 January 2011 667/HB/33930/000

s
Enable Telnet Server Description: Enable or Disable the Telnet server in the outstation. Default: false Username Description: Configure the username for Telnet. Default: Password Description: Configure the password for Telnet Default: Telnet Port Number Description: Configure the port number for the telnet server to use. Default: 23

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.5.14

SysCtl Screen

Figure 163 - SysCtl Enable IP Forwarding Description: Enable or disable IP Forwarding. Default: 0

13.5.15

Firewall Screen

Figure 164 - Firewall Enable IP Firewall Description: Enable or disable IP Firewall (0=disable, 1=enable). Default: 0

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

151 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Rule 1 Description: Enter the IP Firewall rule. See man ipfw for more information. Default: deny ip from 192.168.100.0/24 to me Rule 2 Description: Enter the IP Firewall rule. See man ipfw for more information. Default: allow ip from any to any

13.5.16

Light Weight Tunnel Screen

Figure 165 - LwTunnel Enable Tunnel Description: Enable or disable the tunnel. Default: false Local Virtual Address Description: Configure the local Virtual IP Address. Default: 192.168.100.3 Remote Virtual Address Description: Configure the remote Virtual IP Address. This is only needed for the client (outstation) end. Default: 192.168.100.1 Virtual Netmask Description: Configure the Virtual Netmask Address. Default: 255.255.255.0 Physical Target Address Description: Configure the Real world Tunnel target IP address. Default: 10.2.1.100 Physical Target Port Description: Configure the Real world Tunnel target IP port number. Default: 15370
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 152 of 197 Released 20 January 2011 667/HB/33930/000

s
OS Tunnel Device Description: Configure the Tunnel device name. For example /dev/tun0. Default: /dev/tun0

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Make Defaultroute Description: Configure the tunnel interface as a default route for IP packets. Default: false Reconnect Timeout Description: Configure the time (in seconds) after a disconnect before a client will try to re-connect to the tunnel server. Default: 60 Keyalive Timeout Description: Configure the time (in minutes) that the client will resend a keep alive message. This message is used to keep the tcl connection active. Default: 30 Route Network Description: Configure a custom route for routing IP packets to the Peer. Default: Route NetMask Description: Configure a custom route mask, this goes with the Route Network option. Default: Encryption Key Description: Configure the Tunnel shared secret key. Default: Wp6Xg23R67Bgt

13.5.17

HTTP Screen

Figure 166 - HTTP Enable HTTP server Description: Enable or disable the HTTP server. Default: Username Description: Configure the username needed for authentication. Default:

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

153 of 197 Released 20 January 2011 667/HB/33930/000

s
Password Description: Configure the password needed for authentication. Default: IP Port Description: Configure the IP port that the HTTP server will use. Default: 80

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Use SSL Description: Enable or Disable SSL. SSL provides an encription level to protect data send to and from the web server. Default: false SSL PEM File Description: Configure the PEM (combined Certificate and private key) filename. This file is used by the server to setup the SSL connection to the HTTP client. Default: romfs/ssl/server.pem

13.5.18

Terminal Screen

Figure 167 - Terminal Username Description: Configure the username for handset terminal. Default: Password Description: Configure the password for handset terminal. Default:

13.5.19

Digital IO Screen

Figure 168 - Digital I/O Scan Period Description: Configure the number of milliseconds between input scans. Default: 20
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 154 of 197 Released 20 January 2011 667/HB/33930/000

s
13.5.20 TCL Screen

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 169 - TCL TCL Startup Script Description: Configure the name of the TCL script to auto-start on startup. Default: etc/tcl/script.tcl

13.6 STATUSCONFIG: ENVIRONMENT MONITOR 13.6.1 General Screen

Figure 170 - Temperature - General Poll Period Description: Configure the poll period in milliseconds. Default: 10000 Over Temperature Alarm Threshold Description: Over temperature alarm threshold in degrees Celcius. Default: 70
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 155 of 197 Released 20 January 2011 667/HB/33930/000

s
Under Temperature Alarm Threshold Description: Under temperature alarm threshold in degrees Celcius. Default: 0

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Low Power Mode Enabled Description: Control whether or not low power mode (status LEDs off) is entered when the door is closed: true = low power mode entered when door closed false = low power mode not used Default: true

13.6.2

Status Screen

Figure 171 - Sensor Status Information Current Temperature Description: Read the current temperature in degrees Celsius. Read Only Current Humidity Description: Read the current humidity in %. Read Only Current Light Level Description: Read the current ambient light level in lux. Read Only

13.6.3

Door

Figure 172 - Door Input Information

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

156 of 197 Released 20 January 2011 667/HB/33930/000

s
Door Status Description: The current status of the door(s). Read Only

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Input Port Name Description: Configure the name of the input port used to monitor the door. Default: cpu.in.1 Input Port Debounce Description: Configure the debounce applied to the input port in milliseconds. Default: 100 Input Port Mask Description: Configure the mask applied to the input port. Default: 1 Door IO Sense Description: The sense of the logic for the door IO input: true: closed cct=door closed, open cct=door open false: closed cct=door open, open cct=door closed Default: true

13.6.4

Heater Screen

Figure 173 - Heater Information Heater Status Description: The current status of the heater. Read Only

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

157 of 197 Released 20 January 2011 667/HB/33930/000

s
Heater Control Supported Description: Configure whether control of the heater is supported. Default: false Port Name Description: Configure the name of the IO port. Default: cpu.out.1 Port Mask Description: Configure the mask applied to the IO port. Default: 1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Humidity On Threshold Description: Configure the humidity threshold at which the heater is turned on. Default: 60 Humidity On Threshold Hysteresis Description: Configure the humidity threshold hysteresis for turning the heater on. Default: 1 Temperature On Threshold Description: Configure the temperature threshold at which the heater is turned on. Default: 10 Temperature On Threshold Hysteresis Description: Configure the temperature threshold hysteresis for turning the heater on. Default: 1 Humidity Off Threshold Description: Configure the humidity threshold at which the heater is turned off. Default: 40 Temperature Off Threshold Hysteresis Description: Configure the temperature threshold hysteresis for turning the heater off. Default: 1 Cut Out Temperature Description: The cut out temperature at which the heater is turned off regardless of humidity. Default: 40 Minimum Valid Temperature Description: The lowest temperature reading accepted as valid. Default: -50 Maximum Valid Temperature Description: The highest temperature reading accepted as valid. Default: 100 Minimum Valid Humidity Description: The lowest humidity reading accepted as valid. Default: 0 Maximum Valid Humidity Description: The highest humidity reading accepted as valid. Default: 100

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

158 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Periodic Run Hour Description: The hour at which the periodic maintenance run should occur: 0 to 23 (24 hour notation). Default: 3 Periodic Run Duration Description: The duration for which the periodic maintenance run should last: 1 to 9 minutes. Default: 1

13.7 STATUSCONFIG: GSPI 13.7.1 General

Figure 174 - General Status Poll Period Description: Configure the status poll period in milliseconds. Default: 10000 Reset Time Description: The time allowed (in seconds) for each peripheral to reset when scanning the GSPI bus. Reducing this time can allow faster startup for signs with short rows. Increasing this time allows more time for longer rows to initialise. Default: 6

13.7.2
13.7.2.1

Status
Luminance Screen

Figure 175 - Display of PWM Signals Display PWM Signal 0 Description: Read the setting for display PWM signal 0. Read Only

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

159 of 197 Released 20 January 2011 667/HB/33930/000

s
Display PWM Signal 1 Description: Read the setting for display PWM signal 1. Read Only Display PWM Signal 2 Description: Read the setting for display PWM signal 2. Read Only Lantern PWM Signal 0 Description: Read the setting for lantern PWM signal 0. Read Only Lantern PWM Signal 1 Description: Read the setting for lantern PWM signal 1. Read Only Lantern PWM Signal 2 Description: Read the setting for lantern PWM signal 2. Read Only 13.7.2.2 Communications Screen

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 176 - Communications Number of Broadcast Messages Description: Read the number of broadcast messages transmitted to the GSPI peripherals. Read Only Transmit Messages (n) Description: Read the number of messages transmitted to GSPI peripheral with address n. Read Only Receive Messages (n) Description: Read the number of messages received from GSPI peripheral with address n. Read Only

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

160 of 197 Released 20 January 2011 667/HB/33930/000

s
13.7.3 Upload/Download Screen

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 177 - Upload/Download Upload Block Retries Description: Configure the number of times a failed upload block is requested. Default: 4 Upload Message Retries Description: Configure the number of times a failed upload message is retried. Default: 4 Download Block Retries Description: Configure the number of times a failed download block is resent. Default: 10 Download Block Retries Description: Configure the number of times a failed download block is resent. Default: 10 Firmware Download File Description: Configure the name of the firmware download image file. Default: etc/peripheralFW.hex Firmware Download Retries Description: Configure the number of times a failed firmware download is retried. Default: 10

13.8 STATUSCONFIG: GENERIC IO APPLICATION 13.8.1 General

Figure 178 - Generic IO Application, General

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

161 of 197 Released 20 January 2011 667/HB/33930/000

s
Application Poll Period Description: Configure the application poll period in milliseconds. Default: 1000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.8.2

Status

Figure 179 - Generic IO Application, Status Time of Last Request Description: Read the time of the last request. Read Only Input Pattern Description: Read the current input pattern. Read Only Message Requested Description: Read the requested message derived from the input pattern. Read Only Lanterns Requested Description: Read the requested lanterns from the input pattern. Read Only Request Actioned OK Description: Read the actioned status of the last request. Read Only Current Message Description: Message currently displayed. Read Only Current Lantern State Description: Current lantern state. Read Only Current Status Description: Result of the last update. Read Only

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

162 of 197 Released 20 January 2011 667/HB/33930/000

s
13.8.3 IO

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 180 - Generic IO Application, IO Input port state Description: State of inputs as used by the application Read Only Input Port Name Description: Configure the name of the input port. Default: iocard1.in.1 Input Port Debounce Description: Configure the debounce applied to the input port in milliseconds Default: 10 Input Port Mask Description: Configure the mask applied to the input port (unshifted). Default: 255 Input Port Offset Description: Configure the offset applied to the input port. Default: 0 Input Port Inversion Description: Indicates whether or not the data read from the input port is inverted before use. Default: false Output port state Description: State of outputs as requested by the application Read Only Output Port Name Description: Configure the name of the output port. Default: iocard1.out.2 Output Port Mask Description: Configure the mask applied to the output port (unshifted). Default: 255
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 163 of 197 Released 20 January 2011 667/HB/33930/000

s
Output Port Offset Description: Configure the offset applied to the output port. Default: 0

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Output Port Inversion Description: Indicates whether or not the data written to the output port is inverted before use. Default: false Output Port Fault Description: Configure which bits indicate a fault on the output port. Default: 255

13.8.4

Message Rules Screen

Figure 181 - Message Rules Number of Message Rules Description: The number of message rules. Read Only 13.8.4.1 Rule Screen Rule n

Figure 182 - Rule 0 The number of Rule screens is determined by the number of message rules specified on the Message Rules screen (seeFigure 181). Each rule is used to map an input pattern (as received on the controlling IO interface) to a preset message (see section 13.11.8 for how to define preset messages). Input Pattern Description: Configure the input pattern. Default: 0 Message Number Description: Configure the message number. Default: 0

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

164 of 197 Released 20 January 2011 667/HB/33930/000

s
13.9 STATUSCONFIG: PRODUCTION TESTS 13.9.1 General

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 183 - Production Tests, General Test / Test Step Duration Description: Configure the test or test step duration in seconds. Default: 20 Retries Description: Configure the number of retries. Default: 4 Lanterns Enabled with Preset Messages Description: Enable / disable lanterns with preset messages. Default: false

13.9.2

Log Sensor Readings

Figure 184 - Production Tests, Log Sensor Readings Interval Between Readings Description: Configure the interval between readings in seconds. Default: 1
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 165 of 197 Released 20 January 2011 667/HB/33930/000

s
Test Duration Description: Configure the test duration in seconds. Default: 20

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.9.3

Lantern Brightness

Figure 185 - Production Tests, Lantern Brightness Test Duration Description: Configure the test duration in seconds. Default: 20

13.9.4

Lantern Sequence

Figure 186 - Production Tests, Lantern Sequence On Period Description: Configure the lantern on period in seconds. Default: 20 Off Period Description: Configure the lantern off period in seconds. Default: 0

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

166 of 197 Released 20 January 2011 667/HB/33930/000

s
13.9.5 Display Checkerboard

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 187 - Production Tests, Display Checkerboard X Step Description: Configure the X (horizontal) step value (in pixels). Default: 7 Y Step Description: Configure the Y (vertical) step value (in pixels). Default: 7

13.9.6

Display Preset Message

Figure 188 - Production Tests, Display Preset Message Message Identifier Description: Configure the identifier of the preset message to display. Default: 0 Blank on start Description: Controls whether or not the sign will be blanked on start of the display preset message tests Default: true

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

167 of 197 Released 20 January 2011 667/HB/33930/000

s
13.9.7 Luminance Band

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Blank on completion Description: Controls whether or not the sign will be blanked on completion of the display preset message tests Default: true

Figure 189 - Production Tests, Luminance Band Message Identifier Description: Configure the identifier of the preset message to display. Default: 0 Luminance Band Description: The luminance band used for the sign (0 to 4). Default: 0

13.9.8

Luminance Override

Figure 190 - Production Tests, Luminance Override Message Identifier Description: Configure the identifier of the preset message to display. Default: 0

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

168 of 197 Released 20 January 2011 667/HB/33930/000

s
Display PWM Description: The PWM used for the display boards (0 to 10000). Default: 1000 Lantern PWM Description: The PWM used for the lantern boards (0 to 10000). Default: 1000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.10 STATUSCONFIG: UTMC APPLICATION 13.10.1 General

Figure 191 - General Application Poll Period Description: The application poll period in milliseconds. Default: 100

13.10.2

Instation Compatibility

Figure 192 - Instation Compatibility First Line Description: The start line used in the message table should be 1, however some instation implementations use an index of 0, this option allows the user to define the start index for the message tableThe first line number assumed by the instation in the MIB message table. Default: 1 Start ID Description: Set start sign id to match the value configured / expected at the instation. Default: 0

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

169 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Siemens Fault Reporting Description: Enable or Disable Siemens specific manufacture Fault Description field. When this option is enabled, the faultDescription OID in the MIB is used to show a non-MIB reportable fault has been detected. Default: false Always Report Description: Enable to always report system faults using the Fault Description Field. This option has no effect unless the Siemens Fault Reporting option is also enabled. Default: true Report Message Set Failed on Critical Lantern Fault Description: If true then will report that message set failed in addition to lantern failure when the sign is blanked due to a lantern fault. Useful for instation compatibility. Default: true

13.10.3

MIB Config

Figure 193 - MIB Configuration Instation Trap Address Description: Configure the VMS trap IP address. Default: 0.0.0.0 Instation Trap Port Description: Configure the VMS trap port number. Default: 162 MIB Password Description: Configure the UTMC VMS MIB password. Default: no default

13.10.4

Sign Setup

Figure 194 - Sign Setup


Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 170 of 197 Released 20 January 2011 667/HB/33930/000

s
Exists Description: Flag to enable sign. Default: Enable Type Description: Configure a text field to define the sign type. Default: Elektra Blank Sign Description: Configure the sign to blank on a fault. Default: Blank Display ID Description: Display ID, needs to be set to 0. Default: 0 Lantern Enable Description: Configure Lanterns to be enabled or disabled. Default: Disable 13.10.4.1 Display

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 195 - Display Configuration Display Port Description: Configure the Display Port, should be set to 0. Default: 0 Address Description: Configure the Display Address. Default: 1 Display Height Description: Configure the Display Height in rows. Default: 0 Display Width Description: Configure the Display Width in characters. Default: 0

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

171 of 197 Released 20 January 2011 667/HB/33930/000

s
13.10.4.2 Lantern

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 196 - Lantern Configuration Lantern Port Description: Configure the lantern port. Should be set to 0. Default: 0 Address Description: Configure the lantern address. Default: 1

13.10.5

Comms Check

Figure 197 - Comms Check Enable Comms Check Description: Enable or Disable the UTMC VMS comms check extension. Default: Disable Comms Check Timer Description: Confgure the number of minutes to wait before triggering a comms check event. Default: 60

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

172 of 197 Released 20 January 2011 667/HB/33930/000

s
13.10.6
13.10.6.1

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Luminance Override
Display

Figure 198 - Display Override PWM Levels Fifteen override levels exist, each specified as follows. Display Level n Description: Override n PWM level applied to the display LEDs. Default: depends on n 13.10.6.2 Lantern

Figure 199 - Lantern Override PWM Levels Fifteen override levels exist, each specified as follows.
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 173 of 197 Released 20 January 2011 667/HB/33930/000

s
Lantern Level n Description: Override n PWM level applied to the lantern LEDs. Default: depends on n

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.11 STATUSCONFIG: UVMS LIBRARY 13.11.1 General

Figure 200 - UVMS Library - General Status Description: The current status. Read Only Current Requested Message Description: The message currently requested to be displayed on the sign. Read Only Current Requested Lantern Flashing State Description: The currently requested flashing state of the lanterns on the sign. Read Only Control Thread Poll Period Description: Configure the control thread poll period in milliseconds. Default: 1000 Monitor Thread Poll Period Description: Configure the monitor thread poll period in milliseconds. Default: 1000 Peripheral No Response Threshold Description: The number of GSPI poll messages allowed to be missed before the peripheral is deemed missing. Default: 10 Special Words Compare Facility Description: Configure the sign to support the special word compare facility. Default: false
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 174 of 197 Released 20 January 2011 667/HB/33930/000

s
Lantern Flash Rate Description: Configure the lantern flash rate in milliseconds. Default: 400

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Separate Special Words Description: If selected special words are only detected if separated by spaces from other words. Default: false

Display Luminance Level for Faulty Light Sensor Description: Configure the the display luminance level when the light sensor is faulty. Default: 2500 Lantern Luminance Level for Faulty Light Sensor Description: Configure the the lantern luminance level when the light sensor is faulty. Default: 2500 Light Reading Period Description: Configure the time between light readings in minutes. Default: 1 Light Reading Averaging Count Description: Configure the the number of light readings which are averaged. Default: 3 No light change timeout Description: Timeout (in hours) for detection of no light change e.g. to detect opaque light sensor. Default: 24 Sign Setup Page Auto Refresh Description: Controls whether or not the sign setup web page automatically refreshes. Default: true

13.11.2

Pixel Monitoring

Figure 201 - Pixel Monitoring Critical Fault Threshold for Lanterns Description: Configure the number of pixel faults to report a critical fault on a lantern. Default: 4

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

175 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Critical Fault Threshold for Display Description: Configure the number of pixel faults in a character to report a critical fault on the display. Default: 2 Persist Critical Display Fault Description: If selected then critical display faults are persisted until a restart. This can be useful for compatibility with instations. Deselection can be used to restore the critical display fault status to the current value. Default: true Persist Single Lantern Fault Description: If selected then single lantern faults are persisted until a restart. This can be useful for compatibility with instations. Deselection can be used to restore the single lantern fault status to the current value. Default: true Persist Lantern Pair Fault Description: If selected then lantern pair faults are persisted until a restart. This can be useful for compatibility with instations. Deselection can be used to restore the lantern pair fault status to the current value. Default: true Blank on Lantern Pair Fault Description: If selected then lantern pair faults cause the sign to blank. Default: true Blank on Single Lantern Fault Description: If selected then single lantern faults cause the sign to blank. Default: true Continue to Flash on Lantern Pair Fault Description: If selected then lanterns will continue to flash when pair faults have been detected if sign not blanked. Default: true Continue to Flash on Single Lantern Fault Description: If selected then lanterns will continue to flash when single lantern faults have been detected if sign not blanked. Default: true

13.11.3

Lantern Position

Figure 202 - Lantern Positions Position of Top Left Lantern Description: Configure the identifier for the top left lantern. Default: 0
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 176 of 197 Released 20 January 2011 667/HB/33930/000

s
Position of Top Right Lantern Description: Configure the identifier for the top right lantern. Default: 1 Position of Bottom Left Lantern Description: Configure the identifier for the bottom left lantern. Default: 2 Position of Bottom Right Lantern Description: Configure the identifier for the bottom right lantern. Default: 3

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

13.11.4

PWM Modifiers

Modifiers are available for each of the Luminance Bands to tailor the PWM to match display colour and / or size. 13.11.4.1 Luminance Band Modifier - Band n

Figure 203 - Luminance Modifiers - Band n Display PWM 0 Modifier Description: Configure PWM 0 modifier for display LEDs (%). Default: depends on Luminance Band Display PWM 1 modifier Description: Configure PWM 1 modifier for display LEDs (%). Default: depends on Luminance Band Display PWM 2 modifier Description: Configure PWM 2 modifier for display LEDs (%). Default: depends on Luminance Band Lantern PWM 0 modifier Description: Configure PWM 0 modifier for lantern LEDs (%). Default: depends on Luminance Band Lantern PWM 1 modifier Description: Configure PWM 0 modifier for lantern LEDs (%). Default: depends on Luminance Band Lantern PWM 2 modifier Description: Configure PWM 0 modifier for lantern LEDs (%). Default: depends on Luminance Band
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 177 of 197 Released 20 January 2011 667/HB/33930/000

s
13.11.5 Luminance Bands

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 204 - Luminance Bands Current Luminance Band Description: The luminance band in use if not overridden. Read Only There are five Luminance Bands each defined using four parameters as follows: Luminance Band n Up Threshold Description: Configure the up threshold for luminance band n. Default: depends on Luminance Band Luminance Band n Down Threshold Description: Configure the down threshold for luminance band n. Default: depends on Luminance Band Luminance Band n Display PWM Level Description: Configure the Display PWM level for luminance band n. Default: depends on Luminance Band Luminance Band n Lantern PWM Level Description: Configure the Lantern PWM level for luminance band n. Default: depends on Luminance Band

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

178 of 197 Released 20 January 2011 667/HB/33930/000

s
13.11.6 Graphical Arrows

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 205 - Graphical Arrows Eight directional graphical arrows are supported by the sign. The ASCII string used by the instation to activate each arrow is defined as follows: Graphical Arrow Description: Token used to represent directional arrow. Default: depends on arrow direction

13.11.7

Special Words

Figure 206 - Special Words Each special word is defined as follows. All entries are case sensitive. An empty entry terminates the list: Special Word n Description: Word or phrase to be displayed in alternative colour. Default:

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

179 of 197 Released 20 January 2011 667/HB/33930/000

s
13.11.8 Preset Messages

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 207 - Preset Messages Preset Message 0 Description: Configure a preset message. Note: When entering a message, \n should be used to separate text for separate rows e.g. SIEMENS\nTRAFFIC

13.12 STATUSCONFIG: UVMS OVER IP APPLICATION 13.12.1 General

Figure 208 - General Time to Sign Blank Description: Configure how long communications with the instation is lost before the sign is blanked. Time in seconds. Default: 600 Backoff Poll Period Description: The application poll period during backoff (milliseconds). Default: 1000
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 180 of 197 Released 20 January 2011 667/HB/33930/000

s
13.12.2 Instation IP Communications

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Instation Backoff Period Description: Configure the instation communications backoff period in minutes. Default: 1

Figure 209 - Instation IP Communications Instation IP Address Description: Configure the instation IP address. Default: 0.0.0.0 Instation Port Number Description: Configure the instation port number. Default: 0 Summary: Sign ID Description: The ID of this sign on the UVMS network. Default: 1 Encryption Enabled Description: Protocol encryption is enabled. Default: true Shared Secret Description: The secret shared with the instation used for encryption. Must be 16 characters in length. Default: AaBbCcDdWwXxYyZz Instation Read Timeout Description: Configure the instation read timeout in milliseconds. Default: 1000 Instation Connection Attempts Description: Configure the number of instation connection attempts before backing off. Default: 4 Report Message Set Failed on Critical Lantern Fault Description: If true then will report that message set failed in addition to lantern failure when the sign is blanked due to a lantern fault. Useful for instation compatibility. Default: true
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 181 of 197 Released 20 January 2011 667/HB/33930/000

s
13.12.3 Luminance Overrides

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Figure 210 - Luminance Overrides Display Dim Description: Configure the dim override PWM level applied to the display LEDs. Default: 2500 Display Bright Description: Configure the bright override PWM level applied to the display LEDs. Default: 7500 Lanterns Dim Description: Configure the dim override PWM level applied to the lantern LEDs. Default: 2500 Lanterns Bright Description: Configure the bright override PWM level applied to the lantern LEDs. Default: 7500

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

182 of 197 Released 20 January 2011 667/HB/33930/000

s
14 APPENDICES
14.1 APPENDIX A - INSTALLATION CHECKLIST
Installation first fix
Description Bolts tightened to correct torque? (8.1) Eye-bolt stowed in sign? (8.2.3) Expected value Pass Pass Measured value OK? Description

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Installation second fix (Continued)


Expected value Measured value OK?

Installation supervisor name:

MDU maintenance skt RCD test (10.4) No trip test (15mA) Rated crnt (30mA) Rated crntx5 (150mA)

Pass < 200 ms < 40 ms

Installation supervisor signature:

Installation supervisor name:

Date:

Installation supervisor signature:

Figure 211 - First Fix Checklist Installation second fix


Description
Insulation test (10.1) 500V insulation test Polarity test (10.2) Line earth

Date:

Expected value > 10 M

Measured value

OK?

Figure 212 - Second Fix Checklist

Neutral - earth Line Neutral

200V to 253V rms < 10 V rms 200V to 253V rms

Earth loop impedance Elektra enc (10.3.1.1) Master switch Line I/P to Master Switch cover Master Switch Line I/P to Primary Earth Stud Transformer or SMPS Line I/P to transformer / PSU frame Gemini Line I/p to Comms Panel

< 1.84 < 1.84 < 5.93 < 13.14 < 3.00

Maintenance Socket MCB output to


Maintenance Skt Earth pin

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

183 of 197 Released 20 January 2011 667/HB/33930/000

s
Description
Functional test (See 11) Power up test Gemini hardware config. Diagnostic WEB interface comms Heater test Light sensor test Display test Fault table clear

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

14.2 APPENDIX A - COMMISSIONING CHECKLIST


Expected value Measured value OK?

Pass Pass Pass Pass Pass Pass Pass

Installation supervisor name:

Installation supervisor signature:

Date:

Figure 213 - Commissioning Checklist

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

184 of 197 Released 20 January 2011 667/HB/33930/000

s
14.3 APPENDIX B UPDATING FIRMWARE

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

It is possible to update all firmware within the sign (Gemini, sensor and row-driver) through the web pages. The Gemini firmware contains the peripheral (sensor & row-driver) firmware and so the process is performed in two steps: 1. Update Gemini firmware. This is described in section 14.3.1. 2. Update peripheral firmware if necessary (this may not change between Gemini firmware versions). This is described in section 14.3.2. It is not necessary to perform step two immediately after step one some time may be left between the steps if desired.

14.3.1

Updating Gemini Firmware

14.3.1.1 Upgrade Gemini Already Running Elektra Firmware For upgrade using the web interface please refer to the section on 'Upgrade Screen' in GVP Reference Manual 667/HB/31760/000. For upgrade using the handset interface please refer to the section on 'WIZ: Upgrade' in GVP Reference Manual 667/HB/31760/000. 14.3.1.2 Converting Non-Elektra Gemini for use in Elektra It is likely that the ELEKTRA Gemini has been supplied with the correct firmware, but if it is necessary to convert a non-Elektra Gemini for use in Elektra then the Gemini Firmware Update Tool can be used. Although it is possible to load firmware using the Web Interface, this should only be done if you are upgrading a Gemini which is to continue to be used for the same purpose. The Update Tool must be used if for example you are to change the firmware in a compatible UTMC OTU so it can be used in an ELEKTRA Sign.

IMPORTANT

The following items, both available from the Siemens Mobility Traffic Solutions support site (http://www.siemens.co.uk/traffic/en/index/downloads.htm), are required to perform this operation: The Gemini Firmware Update Tool - a Self Extracting zip file called Update.exe, part number 667/TZ/33901/000. The .jffs2 Elektra file system image part of 667/TZ/33979/000

The following is a Step by Step guide to convert a Gemini Unit using this tool: STEP 1 ACTION The procedure requires the following 1) A computer running either Windows NT, Windows 2000,Windows XP or Windows 98. 2) A serial lead to connect from the computer to the Gemini Unit to be updated. A USB to RS232 converter may be required depending on the laptop. Drag the attached Update.exe onto the desktop of the computer that is to perform the update. Double Click the Update.exe icon on the desktop. A Dialog Box is displayed with the prompt To unzip all files in the Update.exe to the specified folder press the Unzip Button. Before pressing the Unzip Button first decide where the unzipped information will be placed. If the default (C:\) location is required just select Unzip or Browse to a convenient directory and then press Unzip. The Gemini Update information will now be placed in a directory
Public domain 1 A. White Elektra Handbook Page Status Date Document No. 185 of 197 Released 20 January 2011 667/HB/33930/000

2 3 4

Security classification Version Last Editor Document Name

s
6 7

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

8 9 10 11 12

C:\Update (if location of C:\ was selected) Close the Dialog Box To unzip all files ..Button and open Directory C:\ Upgrade. Using Explorer navigate to the directory C:\Upgrade (if default directory C:\ selected). In this directory will be 4 files 1. Readme.txt This gives a brief description of the Update Package. 2. cygwin1.dll this is code required by the Update program 3. GeminiUpgrade.exe this is the executable program that will download the update information to the Gemini Unit. 4. GEMINI FIRMWARE UPDATE TOOL OPERATING PROCEDURE.doc Connect the Gemini Units handset port to Port 1 of the computer. Double Click the GeminiUpgrade.exe icon Follow the instructions on the Dialog Box displayed on the screen. When the Dialog Box OPEN is displayed, select the firmware image to use (ending in .jffs2) and then select OPEN. The remainder of the Update continues with required action prompts until the final Dialog, which instructs the user to Replace Watchdog Link (it is no longer necessary to remove the watchdog link so may not have been removed), press Reset and then press the Space Bar. NOTE - The download process will take between 5 7 minutes. Closedown any Dialog Box associated with the Update Table 10- File System Upgrade Process

13

14.3.2

Programming Peripheral Boards (Sensor & Row Drivers)

Updated peripheral (sensor and row-driver) firmware may be contained in updated Gemini firmware. This can be determined by comparing the firmware version on the Peripheral Firmware Update page with that currently running in the peripherals (given for each peripheral on the Sign Setup page). Section 13.2 contains details of how to update the peripheral firmware.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

186 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

14.4 APPENDIX C IMPORTING / EXPORTING CONFIGURATIONS


Refer to Section on 'Config Import / Export' in GVP Reference Manual 667/HB/31760/000.

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

187 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

14.5 APPENDIX D PART NUMBERS AND SPARES LIST


Use of components other than those listed, or modifications or enhancements that have not been authorised by Siemens Mobility Traffic Solutions may invalidate the warranty and/or safety of this product. Listed below are all the currently available main parts for Elektra Signs. Number
Description General Kit of Parts Master Switch Kit Standard (1 X Former) Master Switch Kit Full (Fully Populated) Master Switch Mounting Panel Master Switch Cover Master Switch Label DIN Rail 235mm Long DIN Rail End Stop Master Switch Sign Mounting Panel 2 Gang Surface Box 20mm Conduit (Socket) End Cover 32A 1-Pole Switch 63A 2-Pole Switch Lightning Protector RCD DBL Socket 30mA Fuseholder 5A Fuseholder 20A Fuseholder BS88 Circuit Breaker 6A Fuse Slow Blow 10A 4W Neutral Block 10A Mains Filter on /000 only ??A Mains Filter on /001 only Light Sensor Assembly Light Sensor Mounting Plate Light Sensor Mounting Plate Seal Light Sensor Light Sensor Box Light Sensor PCB Street Cable Termination Kit Street Cable Anchor Plate Comms Panel Kit Gemini ELEKTRA Comms Mounting Panel Comms Adjust BRKT Comms Slider Work Positioning Bar Fixing Kit Work Positioning Bar Fixing Spacer Work Positioning Bar Fixing Shim Row Driver Module Assembly Sensor Module PCB Assesmbly PSU Assembly 240 Char Only 100mm Ch PCB Assembly Amber 100mm Ch PCB Assembly Red/Green
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No.

TS Part Number 667/1/44605/000 667/1/44650/000 667/1/44650/001 667/2/44651/000 667/2/44652/000 667/2/44653/000 667/2/44654/235 703/4/01366/004 667/2/44655/000 561/4/20921/000 915/4/10337/000 703/4/10328/000 408/4/97165/002 408/4/97165/011 516/4/00136/000 516/4/02062/000 516/4/97053/000 516/4/97053/002 516/4/97064/000 516/4/97076/006 518/4/90352/004 703/4/10285/000 422/4/09906/010 422/4/09906/??? 667/1/44660/000 667/1/44661/000 667/1/44662/000 667/1/31259/001 915/4/10319/000 667/1/31250/000 667/1/44690/000 667/2/44645/000 667/1/44630/000 667/1/32605/102 667/2/44631/000 667/2/44632/000 667/2/44633/000 667/1/44692/000 667/2/44643/000 667/2/44644/000 667/1/33980/002 667/1/33980/001 667/1/33966/001 667/1/33951/001 667/1/33951/002
188 of 197 Released 20 January 2011 667/HB/33930/000

s
160mm Ch PCB Assembly Amber Full Matrix 160mm Ch PCB Assembly Red/Green Full Matrix 160mm Ch PCB Assembly Amber 5 x 7 Matrix 240mm Ch Amber PCB Assembly Lantern Display Assembly (No PSU) Row Driver Module Assembly PSU Assembly 5V Power Cable Assembly Lantern Window PCB Interconnect Cable PCB Power Cable Connector CAT5E RJ45 Cable 0.2m CAT5E RJ45 Cable 0.5m CAT5E RJ45 Cable 1m CAT5E RJ45 Cable 2m CAT5E RJ45 Cable 3m 500VA Transformer Kit TX MTG Plate 500VA Transformer Switched Mode Power Supply Assembly SMPS Mounting Plate PSU Fuse Label SMPS 10A 250V 10A Fuse Terminal Block 1 Way 13A Fused GPRS Option Kit GPRS Modem GPRS Antenna GPRS Modem RS232 Cable GPRS Modem Power Cable Antenna Cable Inspection lamp Kit Ladder Lanyard Kit Ladder Lanyard Tie-Off Ladder Lanyard Label Intercostal to Front Panel Support Kit Intercostal to Front Panel Support Bracket Work Positioning Bar Intercostal Mounting Kit Work Positioning Bar Support Bracket TI Enclosure Frame (Monopole) TI Enclosure Frame (Multi-pole) TI Enclosure Frame (Sign on Stanchion) Door Fixing Kit (Small) Door Fixing Kit (Medium) Door Fixing Kit (Large) 3 Point Lock (Small) 3 Point Lock (Medium) 3 Point Lock (Large) Main Door Hinge Micro Switch Bracket 2.8m Door M/Switch Cable Telescopic Slide 370mm Telescopic Slide Eyelet Ventilation Cover Ventilation Filter Rope
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

667/1/33953/001 667/1/33953/002 667/1/33957/001 667/1/33955/001 667/1/44610/800 667/1/33980/002 667/1/33966/001 667/1/44636/001 667/2/44613/800 667/7/44637/000 998/4/03913/002 998/4/88351/002 998/4/88351/005 998/4/88351/010 998/4/88351/020 998/4/88351/030 667/1/44670/000 667/2/44671/000 667/7/44920/000 667/1/44675/000 667/2/44676/000 667/2/44675/000 605/4/08695/000 518/4/97065/000 703/4/10327/000 667/1/44680/000 656/4/21386/000 640/4/90014/000 667/1/30618/001 667/1/30616/001 667/7/30806/000 667/1/44665/000 667/1/44695/000 667/2/44642/000 667/2/44656/000 667/1/44694/000 667/2/44641/000 667/1/44693/000 667/2/44646/000 667/2/44001/000 667/2/44011/000 667/2/44021/000 667/1/44620/100 667/1/44620/300 667/1/44620/400 667/7/31720/003 667/7/31720/003 667/7/31720/004 667/7/28519/000 667/2/44624/000 667/1/44636/028 999/4/44112/000 999/4/44112/001 667/2/44623/000 412/4/30007/000 998/4/88272/000
Page Status Date Document No. 189 of 197 Released 20 January 2011 667/HB/33930/000

s
Elektra Heater Kit Assembly Relay Din Rail End Stop Din Rail Heater Warning Label Gemini Battery Kit Gemini RTC Back-up Battery 3V Coin Cell Outstation Back-up Battery 12V Sealed Lead Acid Gemini Lead Acid Fuse (5mm x 20mm 5A 250V QB) Processor (5mm x 20mm 250mA 250V QB) RTC Back-up Battery 3V Coin Cell Outstation Back-up Battery 12V Sealed Lead Acid

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

667/1/44685/000 507/4/39652/000 703/4/01366/004 667/7/30336/000 667/2/44658/000 667/1/30615/000 418/4/53433/000 418/4/42314/010 518/4/90285/008 516/4/90285/001 418/4/53433/000 418/4/42314/010

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

190 of 197 Released 20 January 2011 667/HB/33930/000

s
GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

14.6 APPENDIX E GNU GENERAL PUBLIC LICENCE


The text below is the licence for the GNU open software that is embedded in the Outstation firmware. This firmware contains modified GPL code and that source code is available on application to Siemens as per clause 3a or 3b.

The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it,
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 191 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: * a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. * b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. * c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: * a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 192 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

* b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, * c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 193 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. As a special exception, if other files instantiate templates or use macros or inline functions from this file, or you compile this file and link it with other works to produce a work based on this file, this file does not by itself cause the resulting work to be covered by the GNU General Public License. However the source code for this file must still be made available in accordance with section (3) of the GNU General Public License. This exception does not invalidate any other reasons why a work based on this file might be covered by the GNU General Public License. END OF TERMS AND CONDITIONS
Security classification Version Last Editor Document Name Public domain 1 A. White Elektra Handbook Page Status Date Document No. 194 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

14.7 APPENDIX F CERTIFICATE OF CONFORMITY

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

195 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

196 of 197 Released 20 January 2011 667/HB/33930/000

Siemens Mobility, Traffic Solutions


Sopers Lane, Poole, Dorset, BH17 7ER

LAST PAGE OF THE ELEKTRA HANDBOOK

Security classification Version Last Editor Document Name

Public domain 1 A. White Elektra Handbook

Page Status Date Document No.

197 of 197 Released 20 January 2011 667/HB/33930/000

You might also like