ROI-SO3669-061E 030716

P N M S

ASOLINK

ETWORK

Install Manual (WindowsNT)

for version 4.23.XXX

ANAGEMENT

YSTEM

NEC Corporation
Copyright 2001

ROI-S0669

Table of Contents
1. 2. 3. 4. 5. 6. 7. 8. Order of Installation ...................................................................................................................1 Windows NT RAS Setup (Windows NT networking is not yet installed.)................................2 Windows NT RAS Setting (Windows NT with networking already installed) ...................11 Dial-up Setting..........................................................................................................................14 Confirmation of Dial Up Setting ..............................................................................................17 PNMS Setup..............................................................................................................................20 Launching PNMS......................................................................................................................24 NetConfigTool Setup .................................................................................................................25

-i-

ROI-S0669

1. Order of Installation
Notice -Before installing PNMS, Installation of Internet Explorer 5.0 or more is required. -Installation of Acrobat Reader is also required in order to see a help file. Order of installation is described as below.

Step 1: Windows NT Remote Access Service (RAS) Setup

Step 2: Dial-up Networking Setup

Step 3: Pasolink Network Management System (PNMS) Setup

-1-

ROI-S0669

2. Windows NT RAS Setup (Windows NT networking is not yet installed.)

(1) (2) Click on Start | Setting | Control Panel on the Windows NT start tab. Click on Network icon to start configuring the network. Click on Yes button to continue installing networking service.

(3)

Check on Remote access to the network box on Network Setup Wizard, and Cclick on Next button to continue.

-2-

ROI-S0669

(4)

Click on Next button to start searching for network adapters.

(5)

Check on TCP/IP Protocol and click on Next button to continue.

-3-

ROI-S0669

(6)

Select all network services on the list and click on Next button to continue.

(7)

Click on Next button to continue.

-4-

ROI-S0669

(8)

Insert Windows NT Installation CD and input Path. Then click on Continue button.

(9)

Confirmation of DHCP. Click on No button.

(10) Remote Access Setup window, Click on Yes button.

(11) Check on Dont detect my modem box and click on Next button to continue.

-5-

ROI-S0669

(12) Select Standard Modem Types and Standard 19200 Modem from Manufacturers and Models list respectively. Click on Next button to continue.

(13) Select Selected ports and COM1, then click on Next button to continue. If you are using multi-port configuration, select All ports to install the standard 19200 bps modem driver to all available COM ports.

-6-

ROI-S0669

(14) Click on Finish button to finalize the new modem installation.

(15) Select COM1-Standard 19200 bps Modem and click on OK button to continue.

(16) Click on Yes button on the confirmation message window to apply new settings.

-7-

ROI-S0669

(17) Verify that COM1 Standard 19200 bps Modem is displayed on the list. Click on Continue button.

(18) Click on Next button.

-8-

ROI-S0669

(19) Click on Next button.

(20) Click on Next button.

-9-

ROI-S0669

(21) Click on Finish button to finalize the network setup.

(22) Confirmation to reset Windows NT. Click on Yes button. The Windows NT will reset and the changes will take effect after the startup.

- 10 -

ROI-S0669

3. Windows NT RAS Setting (Windows NT with networking already installed)

(1) Open Network on Control Panel

(2)

Go to Services tab. Click on Add button.

- 11 -

ROI-S0669

(3)

Select Remote Access Service and click on OK button.

(4)

Follow steps (8) to (17) of the previous chapter (Chapter 2 Windows NT RAS Setup (Windows NT) networking is not yet installed.).

(5)

Click on Close button in the Network window

- 12 -

ROI-S0669

(6)

Confirmation to reset Windows NT. Click on Yes button. The Windows NT will reset and the changes will take effect after the startup.

- 13 -

ROI-S0669

4. Dial-up Setting
(1) Click on [My Computer] Icon[Dial-up Networking] Icon Then click on OK button on the next prompt. If there are already existing dial-up connections, proceed to step 2.

(2)

On the [New Phonebook Entry Wizard] Window Type in Pnms001 on [Name the new phonebook entry]. Click on Next button to continue.

- 14 -

ROI-S0669

(3)

On the [Server] Window Check I am calling the Internet box then click on Next button.

(4)

On the [Phone Number] Window Type in 1234 (or other dummy value) on [Phone number]. Click on Next button to continue.

- 15 -

ROI-S0669

(5)

On the [New Phonebook Entry Wizard] window Click on Finish button to complete the Dial-up Setting.

(6)

On the [Dial-up Networking] window Click on Close button.

- 16 -

ROI-S0669

5. Confirmation of Dial Up Setting

(1) Click on My Computer |Dial-Up Networking. Select pnmt phonebook entry and click on More |Edit entry and modem properties.. in the context menu.

(2)

On the Basic tab and verify the following entries.

- 17 -

ROI-S0669

(3)

Click on Configure button and set the Initial speed to 19200 bps. Click on OK button when done.

(4)

On the Server tab, verify that the Dial-up server type is set to PPP:Windows NT, Windows 95 Plus, Internet and that TCP/IP box is checked.

- 18 -

ROI-S0669

(5)

Click on TCP/IP Settings button and verify that Server assigned IP address is selected. Force IP header compression and Use default gateway on remote network box should both be checked. Note the most of this are default settings that only needed to be confirmed.

- 19 -

ROI-S0669

6. PNMS Setup
(1) Double-click the setup.exe of PNMS from the folder of CD-ROM.

(2)

Preparing to install. Don't push a Cancel button.

- 20 -

ROI-S0669

(3)

Click Next button.

(4)

Specify the folder where you want to install. Then click Next button.

- 21 -

ROI-S0669

(5)

The check message of an installation start. Click Next button.

(6)

The progress screen of installation. Don't push Cancel button.

- 22 -

ROI-S0669

(7)

The end message of installation. When you push the Close button, it is the completion of installation.

(8)

Check the contents of the Pnms folder.

Note:

You may be required to re-start Windows NT during the installation process due to updates done on some system files by the PNMS installer. If this occurs, please start installation again after re-start.

- 23 -

ROI-S0669

7. Launching PNMS
[1] Click on Start | Programs |PNMS |PNMS to start the application.

[2] Default user name and password are: After installation of PNMS, Initial password is listed below. User name: Admin Password : (No initial password defined. Just press on Enter key. The password can then be modified.)

- 24 -

ROI-S0669

8. NetConfigTool Setup
(1) Double-click the setup.exe in the NetCfgTool folder in the Installation CD-ROM.

(2)

The NetCfgTool installer might prompt you to close some applications (i.e. MS Word, Outlook Express, etc.) before you can continue installation. Close this applications and click on Retry button to resume with the NetCfgTool installation.

(3)

In some cases, NetCfgTool installer might prompt you to restart your PC to update the Windows Installer. In this case, click on Yes button and wait for your PC to restart. The NetCfgTool will automatically resume after your PC is restarted.

- 25 -

ROI-S0669

(4)

The NeCfgTool Setup Wizard window will be started. Select Remove NetCfgTool and click on Finish button to continue removing old NetCfgTool software. If this is a new installation of the NetCfgTool software please proceed to step 7

(5)

The progress of removing will be shown in the ensuing window.

- 26 -

ROI-S0669

(6)

The NetCfgTool Setup Wizard will prompt you when your installation is complete. You should be able to see NetCfgTool has been successfully removed on this window to confirm that you have removed a old application on your PC. Click on Close button to exit the installation wizard.

(7)

Double-click the setup.exe in the NetCfgTool folder in the Installation CD-ROM.

- 27 -

ROI-S0669

(8)

The NeCfgTool Setup Wizard window will be started. Click on Next button to continue installing NetCfgTool.

(9)

On the next window, you will be prompted to specify the folder where you want to install NetConfig Tool. Then click on Next button after specifying the installation folder.

- 28 -

ROI-S0669

(10) Click on Next button on the ensuing confirmation window to start the installation of NetConfig Tool.

(11) The progress of your installation will be shown in the ensuing window. DO NOT click on the Cancel button at this point. Clicking on the Cancel button might corrupt your files.

- 29 -

ROI-S0669

(12)

The NetCfgTool Setup Wizard will prompt you when your installation is complete. You should be able to see NetCfgTool has been successfully installed on this window to confirm that you have installed a good copy of the application on your PC. Click on Close button to exit the installation wizard.

(13) Please verify new NetCfgTool software version on PNMS to judge success for your installation.

- 30 -

ROI-S0669

(14) From your Start Menu, select Programs PNMS PNMS to start the application. Click on NetworkConfiguration|Edit.. window. in the Menu bar on the main PNMS

The NetCfgTool window will be started. Click on Help|About NetCfgTool in the Menu bar on the NetCfgTool window. Please verify new NetCfgTool software version.

- 31 -