NCL30160 1.

0A Constant-Current Buck Regulator for Driving High Power LEDs

The NCL30160 is an NFET hysteretic stepdown, constantcurrent driver for high power LEDs. Ideal for automotive, industrial and general lighting applications utilizing minimal external components. The NCL30160 operates with an input voltage range from 6.3 V to 40 V. The hysteretic control gives good power supply rejection and fast response during load transients and PWM dimming to LED arrays of varying number and type. A dedicated PWM input (DIM/EN) enables wide range of pulsed dimming and a high switching frequency up to 1.4 MHz allows the use of smaller external components minimizing space and cost. Protection features include resistorprogrammed constant LED current, shorted LED protection, undervoltage and thermal shutdown. The NCL30160 is available in a SOIC8 package.
Features http://onsemi.com

8 1 SOIC8 NB CASE 751

MARKING DIAGRAM
8 30160 ALYWX G 1 A L Y W G = Assembly Location = Wafer Lot = Year = Work Week = PbFree Package

Integrated 1.0A MOSFET VIN Range 6.3 V to 40 V Short LED Shutdown Protection Up to 1.4 MHz Switching Frequency No Control Loop Compensation Required Adjustable LED Current Single Pin Brightness and Enable/Disable Control Using PWM Supports AllCeramic Output Capacitors and Capacitorless Outputs Thermal Shutdown Protection Capable of 100% Duty Cycle Operation This is a PbFree Device LED Driver Constant Current Source Automotive Lighting General Illumination Industrial Lighting

PIN CONNECTIONS
CS CS GND VCC LX VIN DIM/ENABLE ROT

Typical Application ORDERING INFORMATION

Device NCL30160DR2G Package Shipping SOIC8 2500 / Tape & Reel (PbFree)

For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.

Semiconductor Components Industries, LLC, 2012

January, 2012 Rev. 1

Publication Order Number: NCL30160/D

NCL30160
VIN CIN D1

LED LED

L1

VIN DIM/Enable ROT ROT VCC CVCC

LX

CS NCL30160 GND RSENSE

Figure 1. Typical Application Circuit

PIN FUNCTION DESCRIPTION

Pin 1, 2 3 4 Pin Name CS GND VCC Description Current Sense feedback pin Ground Pin Output of Internal 5 V linear regulator Application Information Set the current through the LED array by connecting a resistor from this pin to ground. Ground. Reference point for all voltages The VCC pin supplies the power to the internal circuitry. The VCC is the output of a linear regulator which is powered from VIN. A 2 uF ceramic capacitor is recommended for bypassing and should be placed as close as possible to the VCC and AGND pins. Do not connect to an external load. Resistor ROT from this pin to VCC sets the OffTime range for the hysteretic controller. Connect a logiclevel PWM signal to this pin to enable/disable the power MOSFET and LED array Nominal operating input range is 6.3 V to 40 V. Input supply pin to the internal circuitry and the positive input to the current sense comparators. Due high frequency noise, a 10 mF ceramic capacitor is recommended to be placed as close as possible to VIN and power ground. The LX pin connects to the inductor and provides the switching current necessary to operate in hysteretic mode.

5 6 7

ROT DIM/EN VIN

OffTime Setting Resistor PWM Dimming Control & ENABLE Input Voltage Pin

LX

Drain of Internal Power MOSFET

http://onsemi.com
2

NCL30160
MAXIMUM RATINGS
Rating VIN to GND MOSFET Drain Voltage to GND VCC to GND DIM/EN to GND CS to GND ROT to GND Absolute Maximum Junction Temperature Operating Junction Temperature Range Maximum LED Drive Current Storage Temperature Range Thermal Characteristics SOIC8 Plastic Package Maximum Power Dissipation @ TA = 25C (Note 1) Thermal Resistance JunctiontoAir (Note 2) PbFree (Note 3) Symbol VIN LX VCC DIM CS ROT TJ(MAX) TJ ILIM Tstg 40 1.5 55 to +125 Min 0.3 0.3 0.3 0.3 150 125 Max 40 40 6 6 6 6 Unit V V V V V V C C A C

PD RqJA TL MSL

1.11 111.7 260 peak 1

W C/W C

Lead Temperature Soldering (10 sec): Reflow (SMD styles only) Moisture Sensitivity Level (Note 4)

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The maximum package power dissipation limit must not be exceeded.

PD +

TJ(max) * T A R qJA

2. When mounted on a multilayer board with 35 mm2 copper area, using 1 oz Cu. 3. 60180 seconds minimum above 237C. 4. Moisture Sensitivity Level (MSL): 1 per IPC/JEDEC standard: JSTD020A.

http://onsemi.com
3

NCL30160
ELECTRICAL CHARACTERISTICS (Unless otherwise noted: VIN = 12 V, TA = 25C, unless otherwise specified.)
Symbol SYSTEM PARAMETERS VIN IQ_IN VCC VUV+ VUV Input Supply Voltage Range Normal Operation Functional (Note 5) Quiescent Current into VIN Internal Regulator Output (Note 6) UnderVoltage Lockout Threshold (VIN Rising) UnderVoltage Lockout Threshold (VIN Falling) 5.5 5.2 8.0 6.3 1.5 5.0 6.0 5.6 6.5 6.3 mA V V V 40 V Characteristics Min Typ Max Unit

CURRENT LIMIT AND REGULATION VCS_UL VCS_LL VOCP FSW DIM INPUT VPWMH/L VPWML IDIMPU fpwm dmax POWER MOSFET VBRDSS IDSS RDS(on) VSD tPD_Off THERMAL SHUTDOWN TSD THyst OFF TIMER tOFFMIN Minimum Offtime 137 ns Thermal Shutdown Thermal Hysteresis 165 40 C C DraintoSource Breakdown Voltage DraintoSource Leakage Current (VGS = 0 V, VDS = 40 V) On Resistance (Id = 500 mA) SourceDrain Body Diode (Forward OnVoltage) Propagation Delay VCS_UL LX_High 0.8 35 40 10 55 1.1 V mA mW V ns PWM (DIM/EN) high level input voltage PWM (DIM/EN) low level input voltage DIM/EN Pullup Current PWM (DIM/EN) dimming frequency range Maximum Duty Cycle (Note 7) 0.1 100 50 20 1.4 0.4 V V mA kHz % CS Regulation Upper Limit (CS Increasing, FET TurnsOFF) CS Regulation Lower Limit (CS Decreasing, FET TurnsON) Over Current Protect Limit (Reference to CS Pin) Switching Frequency Range (Note 7) 25C 40 to 125C 25C 40 to 125C 213 209 174 171 500 1400 180 220 226 231 186 189 mV kHz mV mV

5. The functional range of VIN is the voltage range over which the device will function. Output current and internal parameters may deviate from normal values for VIN and VCC voltages between 6.3 V and 8 V, depending on load conditions 6. VCC should not be driven from a voltage higher than VIN or in the absence of a voltage at VIN. 7. Guaranteed by design.

http://onsemi.com
4

NCL30160
VIN VCC 5 V Regulator (6.3 V to 40 Vmax) Enable PullUp Resistor S R Q Q Peak Current Comparator 220 mV CS Timer (toff) & Thermal Shutdown Valley Current Comparator 180 mV Short Circuit Protection Comparator 500 mV Gate Driver DIM / Enable

LX

VCC

ROT

GND

Figure 2. Simplified Block Diagram

TYPICAL APPLICATION CIRCUITS AND WAVEFORMS

(TJ = 25C, Unless Otherwise Specified) D1

VIN CIN

L1 LED

VIN DIM/Enable ROT PWM ROT VCC CVCC

LX

CS NCL30160 GND RSENSE

Figure 3. Typical Application Circuit To Drive One LED (Buck)

http://onsemi.com
5

NCL30160

Figure 4. Typical Operation Waveforms (VCC = 12 V, VLED = 6.5 V, RSENSE = 0.68 W, L = 100 mH)

THEORY OF OPERATION This switching power supply is comprised of an inverted buck regulator controlled by a current mode, hysteretic control circuit. The buck regulator operates exactly like a conventional buck regulator except the power device placement has been inverted to allow for a low side power FET. Referring to Figure 1, when the FET is conducting, current flows from the input,through the inductor, the LED and the FET to ground. When the FET shuts off, current continues to flow through the inductor and LED, but is diverted through the diode (D1). This operation keeps the current in the LED continuous with a continuous current ramp. The control circuit controls the current hysteretically. Figure 2 illustrates the operation of this circuit. The CS comparator thresholds are set to provide a 10% current ripple. The peak current comparator threshold of 220 mV sets Ipeak at 10% above the average current while the valley current comparator threshold of 180 mV sets Ivalley at 10% below the average current. When the FET is conducting, the current in the inductor ramps up. This current is sensed by an external sense resistor that is connected from CS to ground. When the CS pin reaches 220 mV, the peak current comparator turns off the power FET. A conventional hysteretic controller would monitor the load current and turn the switch back on when the CS pin reaches 180 mV. But in this topology, the current information is not available to the control circuit when the FET is off. To set the proper FET off time, the CS voltage is sensed when the FET is turned back on and a correction signal is sent to the off time circuit to adjust the off time as necessary.

Figure 5. Typical Current Waveforms

The current waveshape is triangular, and the peak and valley currents are controlled. The average value for a triangular waveshape is halfway between the peak and valley, so even with changes in duty cycle due to input voltage variations or load changes, the average current will remain constant. In the event there is a shortcircuit across the LEDs, a large amount of current could potentially flow through the circuit during startup. To protect against this, the NCL30160 comes with a short circuit protection feature. If the voltage on the CS pin is detected to be greater than 500 mV (equating to 2.5 times the intended average output current), the NCL31060 will turn off the FET, and prevent the FET from turning on again until power is recycled to NCL30160.

http://onsemi.com
6

NCL30160

Figure 6. Short-Circuit Protection

Figure 7. Dimming Waveforms

When VIN rises above the UVLO threshold voltage, switching operation of the FET will begin. However, until the VIN voltage reaches 8 V, the VCC regulator may not provide the expected gate drive voltage to the FET. This could result in the RDS(on) of the FET being higher than expected or there not being enough gate drive capability to operate at the maximum rated switching frequency. For optimal performance, it is recommended to operate the part at a VIN voltage of 8 V or greater.
Setting The Output Current

By applying a pulsed signal to DIM/EN, the average output current can be adjusted to the duty ratio of the pulsed signal. It is recommended to keep the frequency of the DIM/EN signal above 100 Hz to avoid any visible flickering of the LED.

The average output current is determined as being the middle of the peak and valley of the output current, set by the CS comparator thresholds. The nominal average output current will be the current value equivalent to 200 mV at the CS pin. The proper RSENSE value for a desired average output current can be calculated by:
R SENSE + PWM Dimming 200 mV I LED Figure 8. Dimming Performance Inductor Selection

For a given RSENSE value, the average output current, and therefore the brightness of the LED, can be set to a lower value through the DIM/EN pin. When the DIM/EN pin is brought low, the internal FET will turn off and switching will remain off until the DIM/EN pin is brought back into its high state.

The inductor that is used directly affects the switching frequency the driver operates at. The value of the inductor sets the slope at which the output current rises and falls during the switching operation. The slope of the current, in turn, determines how long it takes the current to go from the valley point of the current ripple to the peak when the FET is on and the current and rising, and how long it takes the current to go from the peak point of the current to the valley when the FET is off and the current is falling. These times can be approximated from the following equations:
t ON + VIN * V LED * I OUT L FET R DI
DS

(on) ) DCRL ) RSENSE

http://onsemi.com
7

NCL30160
t OFF + L DI V LED ) V diode ) I OUT DCRL

Where DCRL is the dc resistance of the inductor, VLED is the forward voltages of the LEDs, FETRDS(ON) is the on-resistance of the power MOSFET, and Vdiode is the forward voltage of the catch diode. The switching frequency can then be approximated from the following:
f SW + 1 t ON ) t OFF

It is also important to select a diode that is capable of withstanding the peak reverse voltage it will see in the application. It is recommended to select a diode with a rated reverse voltage greater than VIN. It is also recommended to use a low-capacitance Schottky diode for better efficiency performance.
Selecting The Off-Time Setting Resistor

Higher values of inductance lead to slower rates of rise and fall of the output current. This allows for smaller discrepancies between the expected and actual output current ripple due to propagation delays between sensing at the CS pin and the turning on and off of the power MOSFET. However, the inductor value should be chosen such that the peak output current value does not exceed the rated saturation current of the inductor.
Catch Diode Selection

The off-time setting resistor (ROT) programs the NCL30160 with the initial time duration that the MOSFET is turned off when the switching operation begins. During subsequent switching cycles, the voltage at the CS pin is sensed every time the MOSFET is turned on, and the off-time will be adjusted depending on how much of a discrepancy exists between the sensed value and the CS lower limit threshold value. The ROT value can be calculated using the following equation:
R OT + t OFF 10 11 W

The catch diode needs to be selected such that average current through the diode does not exceed the rated average forward current of the diode. The average current through the diode can be calculated as:
I avg_diode + I OUT t OFF t ON ) t OFF

Where tOFF is the expected off time during normal switching operation, calculated in the Inductor Selection section above.
Input Capacitor

A decoupling capacitor from VIN to ground should be used to provide the current needed when the power MOSFET turns on. A 4.7 mF ceramic capacitor is recommended.

http://onsemi.com
8

NCL30160
100 95 90 EFFICIENCY (%) 85 80 75 70 65 60 0 5 10 15 20 VIN (V) 25 30 35 40 EFFICIENCY (%) 100 95 90 85 80 75 70 65 60 0 5 10 15 20 VIN (V) 25 30 35 40

Figure 9. Efficiency, 350 mA, Vf_LED = 3.5 V

100 95 90 EFFICIENCY (%) IQIN (mA) 85 80 75 70 65 60 0 5 10 15 20 VIN (V) 25 30 35 40 1.70 1.65 1.60 1.55 1.50 1.45 1.40 1.35 1.30 5

Figure 10. Efficiency, 700 mA, Vf_LED = 3.5 V

10

15

Figure 11. Efficiency, 1 A, Vf_LED = 3.5 V

700 600 LED CURRENT (mA) 500 100 Hz 400 300 200 100 10 kHz SWITCHING FREQUENCY (kHz) 240 220 200 180 160 140 120 100 40 20 0

Figure 12. IQIN vs. VIN

20 25 VIN (V)

30

35

40

20

40 60 DIMMING DUTY RATIO (%)

80

100

20 40 60 TEMPERATURE (C)

80

100

120

Figure 13. LED Current vs. Dimming Duty Ratio

Figure 14. Switching Frequency vs. Temperature (12 V VIN, 3 LEDs, 0.7 A, 0.47 mH)

http://onsemi.com
9

NCL30160
PACKAGE DIMENSIONS
SOIC8 NB CASE 75107 ISSUE AK
X A
8 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 75101 THRU 75106 ARE OBSOLETE. NEW STANDARD IS 75107. DIM A B C D G H J K M N S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244

B
1

S
4

0.25 (0.010)

Y G

C Z H D 0.25 (0.010)
M SEATING PLANE

X 45 _

0.10 (0.004)

Z Y

SOLDERING FOOTPRINT*

1.52 0.060

7.0 0.275

4.0 0.155

0.6 0.024

1.270 0.050
SCALE 6:1 mm inches

*For additional information on our PbFree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone : 3036752175 or 8003443860 Toll Free USA/Canada Fax: 3036752176 or 8003443867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 8002829855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81358171050 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative

http://onsemi.com
10

NCL30160/D