Encoder H9720
Encoder H9720
Encoder H9720
x Small Size
x Low Cost
x Multiple Mounting Options
x Wide Resolution Range
x Linear and Rotary Options Available
x No Signal Adjustment Required
x Insensitive to Radial and Axial Play
x -40C to +85C Operating Temperature
x Two Channel Quadrature Output
x TTL Compatible
x Single 5V Supply
x Wave Solderable
Mounting Option #50 - Standard (Baseplane Mounting) Contact Factory for Detailed Package Dimensions
ESD WARNING; NORMAL HANDLING PRECAUTIONS SHOULD BE TAKEN TO AVOID STATIC DISCHARGE.
HEDS-970x, HEDS-972x Series
Digital Output Small Optical Encoder Modules
Data Sheet
Package Dimensions
Description
The HEDS-9700 series is a high performance, low cost,
optical incremental encoder module. When operated
in conjunction with either a codewheel or codestrip,
this module detects rotary or linear position. The
module consists of a lensed LED source and a detector
IC enclosed in a small C-shaped plastic pack age. Due
to a highly collimated light source and a unique photo-
detector array, the module is extremely tolerant to
mounting misalignment.
The two channel digital outputs and 5V supply input are
accessed through four solder-plated leads located on
2.54 mm (0.1 inch) centers.
The standard HEDS-9700 is designed for use with an 11
mm optical radius codewheel, or linear codestrip. Other
options are available. Please contact factory for more in-
formation.
2
Applications
The HEDS-9700 provides sophisticated motion detection
at a low cost, making closed-loop control very cost-com-
petitive! Typical applications include printers, plotters,
copiers, and oce automation equipment.
Note: Avago Technologies encoders are not recom-
mended for use in safety critical applications. Eg. ABS
braking systems, power steering, life support systems
and critical care medical equipment. Please contact
sales representative if more clarication is needed.
Theory of Operation
The HEDS-9700 is a C-shaped emitter/detector module.
Coupled with a codewheel, it translates rotary motion
into a two-channel digital output. Coupled with a
codestrip, it translates linear motion into a digital
output.
As seen in the block diagram, the module contains a
single Light Emitting Diode (LED) as its light source. The
light is collimated into a parallel beam by means of a
single lens located directly over the LED. Opposite the
emitter is the integrated detector circuit. This IC consists
of multiple sets of photodetectors and the signal
processing circuitry necessary to produce the digital
waveforms.
The codewheel/codestrip moves between the emitter
and detector, causing the light beam to be interrupted
by the pattern of spaces and bars on the code wheel/
codestrip. The photodiodes which detect these interrup-
tions are arranged in a pattern that corresponds to the
radius and count density of the codewheel/codestrip.
These detectors are also spaced such that a light period
on one pair of detectors corresponds to a dark period on
the adjacent pair of detectors. The photodiode outputs
are fed through the signal processing circuitry. Two
comparators receive these signals and produce the nal
outputs for channels A and B. Due to this integrated
phasing technique, the digital output of channel A is in
quadrature with channel B (90 degrees out of phase).
Block Diagram
RESISTOR
LENS
LED
COMPARATORS
PHOTO-
DIODES
SIGNAL
PROCESSING
CIRCUITRY
+
-
A
2
A
EMITTER SECTION CODE
WHEEL
DETECTOR SECTION
+
-
B
4
GND
1
V
CC
3
B
CHANNEL A
CHANNEL B
3
Pulse Width (P): The number of electrical degrees that
an output is high during one cycle. This value is nomi-
nally 180e or 1/2 cycle.
Pulse Width Error (AP): The deviation, in electrical de-
grees, of the pulse width from its ideal value of 180e.
State Width (S): The number of electrical degrees be-
tween a transition in the output of channel A and the
neighboring transition in the output of channel B. There
are 4 states per cycle, each nominally 90e.
State Width Error (AS): The deviation, in electrical de-
grees, of each state width from its ideal value of 90e.
Phase (o): The number of electrical degrees between the
center of the high state of channel A and the center of
the high state of channel B. This value is nominally 90e
for quadrature output.
Phase Error (Ao): The deviation of the phase from its
ideal value of 90e.
Direction of Rotation: When the codewheel rotates
counterclock wise, as viewed looking down on the mod-
ule (so the marking is visible), channel A will lead chan-
nel B. If the codewheel rotates in the opposite direction,
channel B will lead channel A.
Optical Radius (Rop): The distance from the codewheels
center of rotation to the optical center (O.C.) of the
encoder module.
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Notes
Storage Temperature T
S
-40 85 C See Note
Operating Temperature T
A
-40 85 C See Note
Supply Voltage V
CC
-0.5 7 V
Output Voltage V
O
-0.5 V
CC
V
Output Current per I
O
-1.0 5 mA
Channel
Soldering Temperature 260 C t 5 sec.
Output Waveforms
Denitions
Count (N) = The number of bar and window pairs or
counts per revolution (CPR) of the codewheel, or the
number of lines per inch of the codestrip (LPI).
1 Shaft Rotation = 360
mechanical
degrees
= N cycles
1 cycle (c) = 360 electrical
degrees (e)
= 1 bar and
window pair
P
C
ROTATION
CHANNEL A
CHANNEL B
A
M
P
L
I
T
U
D
E
S1 S4 S2 S3
4
Encoding Characteristics
Encoding Characteristics over Recommended Operating Range and Recommended Mounting Tolerances. These
characteristics do not include codewheel/codestrip contributions.
Case 1 Case 2
Parameter Symbol Typ. Max. Max. Units Notes
Pulse Width Error AP 7 30 40 e
Logic State Width Error AS 5 30 40 e
Phase Error Ao 2 10 15 e
Case 1: Module mounted on tolerances of 0.13 mm (0.005). Case 2: Module mounted on tolerances of 0.25 mm
(0.010)
Note: See Figures in Mounting Considerations for details on Case 1 and Case 2 mounting tolerances.
Recommended Operating Conditions
Parameter Symbol Min. Max. Units Notes
Temperature T -40 85 C
Supply Voltage V
CC
4.5 5.5 V Ripple < 100 mV
p-p
Load Capacitance C
L
100 pF 3.2 kO pull-up
Count Frequency 20 kHz (Velocity (rpm) x N)/60
Note: The module performance is guaranteed to 20 kHz but can operate at higher frequencies. For operation at 30KHz for resolution options E, F,
G and H, the maximum pulse width and logic state width errors are 40e and phase error is 15e.
Electrical Characteristics
Electrical Characteristics over Recommended Operating Range, Typical at 25C.
Parameter Symbol Min. Typ. Max. Units Notes
Supply Current I
CC
17 40 mA
High Level Output Voltage V
OH
2.4 V I
OH
= -40 A
Low Level Output Voltage V
OL
0.4 V I
OL
= 3.2 mA
Rise Time t
r
200 ns C
L
= 25 pF, R
L
= 11 kO
Fall Time t
f
50 ns C
L
= 25 pF, R
L
= 11 kO
5
Recommended Codewheel and Codestrip Characteristics
Mounting Option #51 Rounded Outline (Baseplane Mounting)
Parameter Symbol Min. Max. Units Notes
Window/Bar Ratio Ww/Wb 0.7 1.4
Window Length (Rotary) Lw 1.80 2.30 mm
(0.071) (0.091) (inch)
Absolute Maximum Codewheel Rc Rop + 3.40 mm Includes eccen
Radius (Rotary) (Rop + 0.134) (inch) tricity errors
Center of Post to Inside W1 1.04 mm
Edge of Window (0.041) (inch)
Center of Post to Outside W2 0.76 mm
Edge of Window (0.030) (inch)
Center of Post to Inside Edge L 3.60 mm
of Codestrip (0.142) (inch)
Optional Packages Available
6
Optional Packages Available (contd.)
Mounting Option #52 Backplane (Backplane Mounting)
Mounting Option #53 Standard with Posts (Baseplane Mounting)
7
Optional Packages Available (contd.)
Mounting Option #54 Tabless (Baseplane Mounting)
Mounting Option #55 Backplane with Posts (Backplane Mounting)
8
Bent Lead Option
Note: These dimensions include shaft end play and codewheel warp.
All dimensions for mounting the module and codewheel/codestrip should be measured with respect to the two mounting posts, shown above.
Mounting Tolerances
Case 1 and Case 2 specify the mounting tolerances required on Rm in order to achieve the respective encoding
characteristics shown on page 4. The mounting tolerances are as follows:
Case 1: Rm 0.13 mm (.005 inches)
Case 2: Rm 0.25 mm (.010 inches)
Recommended Screw Size: M2.5 x 0.45 or 2-56
Mounting Considerations
9
Recommended Wave Solder Conditions
Flux RMA Water Soluble (per MIL-F-14256D)
Process Parameters
1. Flux
2. Pre-heat 60 seconds total
Nominal preheat temp: 90C
Min: 85C Max: 110C
3. Solder Pot Zone
Nominal dip in time:
2.5 - 4.5 seconds
Min: 2.5 seconds
Max: 5 seconds
PCB top side: 140 -160C
PCB bottom side: 240 - 260C
4. Wave Solder 255C,
1.2 meters/minute line speed
5. Hot Water Wash
1st: 30C 45 seconds
2nd: 70C 90 seconds
6. Rinse
1st: 23C 45 seconds
2nd: 23C 45 seconds
7. Dry
1st: 80C 105 seconds
2nd: 95C 105 seconds
Typical Interface
HOST PROCESSOR
CH B
CH A
HEDS9700
AVAGO
HCTL-20xx
QUADRATURE
DECODER/
COUNTER
Ordering Information
Note: Please contact factory for codewheel and codestrip information.
50 51 52 53 54 55
HEDS-9700 K
C *
D * *
E *
F * * * *
G
H * * * *
L
M
P
HEDS-9701 K
C * *
D
E * *
F * *
G
H * * *
L
M
P
50 51 52 53 54 55
HEDS-9720 K
C
D
E
F
G
H
L * * *
M
P * * * * *
HEDS-9721 K
C
D
E
F
G
H
L *
M
P * * *
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright 2005-2010 Avago Technologies. All rights reserved. Obsoletes 5988-8045EN
AV02-0511EN - February 5, 2010
HEDS-97
Resolution Options
(11 mm optical radius, Rop)
K 96 CPR
C 100 CPR
D 192 CPR
E 200 CPR
F 256 CPR
G 360 CPR
H 400 CPR
(Linear)
L 120 LPI
M 127 LPI
P 150 LPI
Lead Bend
0 Straight Leads
1 Bent Leads
0 Rotary
2 Linear
Mounting Options
50 Standard
51 Rounded Outline
52 Backplane
53 Standard w/Posts
54 Tabless
55 Backplane w/Posts
Contact Factory for Other
Resolution Options
Option