Parker - PTFE Lip Seals

PTFE Lip Seal Design Guide
Catalog EPS 5340/USA
!
WARNING:
Failure, improper selection or improper use of the products and/or systems described herein or related items can cause death, personal injury or property damage. For safe and trouble-free use of these products, it is important that you read and follow the Parker Seal Group Product Safety Guide. This Safety Guide can be referenced and downloaded free of charge at www.parkerseals.com and can be ordered, without charge, as Parker Publication No. PSG 5004 by calling 1-800-C-PARKER.
This document, along with other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors, provides product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through his or her own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice.
OFFER OF SALE
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This offer and its acceptance are governed by the provisions stated on the separate page of this document entitled Offer of Sale.
2006 Parker Hannifin Corporation

Parker Hannifin Corporation EPS Division Tel: (801) 972-3000 Fax: (801) 973-4019
www.parkerseals.com
PTFE Lip Seal Design Guide Table of Contents
Introduction
Engineering
Materials
Product Offering FlexiSeal Rod & Piston Seals FlexiSeal Face Seals FlexiSeal Rotary Seals
FlexiLip Rotary Seals
FlexiCase Rotary Seals
www.parkerseals.com
Design Action Request Form
Problem Solved Case Studies
PTFE Lip Seal Design Guide Appendix
Chemical Compatibility
ISO Tolerances
Other Parker Products
www.parkerseals.com
Introduction
The PTFE Lip Seal Design Guide is your premier PTFE seal selection guide for hardware design, seal configuration and material specification options for a wide range of standard and complex applications.
Parker Hannifin is a recognized industry leader focused on achieving innovative sealing solutions for the most demanding engineering applications. Parkers broad range of PTFE Lip Seals include: FlexiSeal , FlexiLip, FlexiCase
FlexiSeal
The FlexiSeal is a spring-energized U-cup utilizing a variety of jacket profiles, spring types and materials in Rod & Piston, Face and Rotary seal configurations. FlexiSeals are used where elastomeric seals fail to meet the temperature range, chemical resistance or friction requirements. Jacket profiles are made from PTFE and other high performance polymers. Spring types are available in corrosion-resistant metal alloys, including stainless steel, Elgiloy * and Hastelloy**.
FlexiLip
FlexiLip seals are rotary seals incorporating a deflected lip seal geometry. Anti-rotational devices such as flanges and O-rings are often utilized to prevent the seal from rotating with the shaft. Standard and custom sizes are available with a wide selection of PTFE materials. FlexiLip seals are suitable for sealing corrosive and abrasive media. A wide range of geometries and materials are available, depending on specific application requirements.
FlexiCase
The FlexiCase seal is a metal-cased rotary lip seal suitable for applications where elastomeric lip seals fail and mechanical seals are too costly. The filled PTFE element provides greater chemical compatibility, wider temperature ranges, higher pressure capabilities, and longer life than elastomeric lip seals.
** Elgiloy is a registered mark of Elgiloy Specialty Metals, Elgin, IL. ** Hastelloy is a registered mark of Haynes International Inc., Kokomo, IN. 01/15/06
1-1
www.parkerseals.com
Introduction
1
FlexiSeal Profiles
FBC-V FRC-V FPC-V
FBS-V FRS-V FPS-V
FBG-V FRG-V FPG-V
FBD-V FRD-V FPD-V
FBK-V FRK-V FPK-V
FBM-V FRM-V FPM-V
FBL-V FRL-V FPL-V
FBN-H FRN-H FPN-H
FBS-H FRS-H
FBG-H FPG-H
FBN-C FRN-C FPN-C
FBS-C FPS-C
FBG-C FRG-C
FEC-V
FED-V
FEK-V
FEN-C
FEN-H
FIN-H
FIC-V
FID-V
FIK-V
FIN-C
FCC-C
FCC-V
FCS-V
FCS-C
FHC-V
FHS-V
FHC-C
FHS-C
FFC-V
FFS-V
FFC-C
FFS-C
FFN-H
FlexiLip Profiles
LFN-N
LEN-N
LDN-N
LMN-N
LFE-N
LEE-N
LDE-N
LGN-N
LFN-S
LEN-S
LDN-S
LMN-S
LFE-S
LEE-S
LDE-S
LGN-S
FlexiCase Profiles
CFN
CMN
CEN
CDN
CGN
CJN
CHN
CFE
CME
CEE
CDE
CGE
CJE
CHE 01/15/06
For additional information on all profiles, see Tab 4.
1-2
www.parkerseals.com
Introduction Engineering Excellence

Parker Hannifin Corporations Engineered Polymer Systems (EPS) Division has a dedicated PTFE engineering team strategically focused on achieving innovative sealing solutions for the most demanding engineering applications. Our design/ application engineers use state-of the-art CAD (2D/3D modeling) systems to custom fit innovative sealing designs to meet and exceed the unique standards set forth by our customers. Parkers engineering staff is consistently dedicated and willing to explore new ideas with the companies and individuals we serve. Different companies come to Parker for different reasons, but our engineering role is always the same working to help those companies, with Parkers engineering expertise, to make anything possible.
Electronic Ordering
To manage your supply chain efficiently, you need up-to-the-minute information on stock levels and an ordering system that minimizes paperwork. Parker offers state-of-the-art ordering systems like ParZap and PHconnect, designed to improve efficiency. Our ParZap System combines powerful inventory management software with a convenient hand-held scanner, allowing you to place orders directly to your local distributor or Parker Service Center. And our Internet-based EDI capabilities allow you to track your orders in real-time from anywhere in the world.
Applications
PTFE FlexiSeal, FlexiLip and FlexiCase seals are utilized in a variety of industries. In fact, this PTFE Lip Seal Design Guide exists separately from other Parker EPS market-specific publications precisely because virtually every industry has specific needs for the unique physical and chemical properties of these remarkable seals. PTFEs high temperature rating and tolerance of a wide range of chemicals make it suitable in Aerospace Jet Engines as a static or dynamic seal.
Quality Commitment
Parker is committed to consistently delivering excellence in quality and service through our continuous improvement of our people, products and systems. Our FlexiSeal manufacturing facilities are certified to AS9100 and ISO/9000 standards. Our commitment to quality and service is supported by our investment in technologically advanced test and inspection methods. Were constantly striving to improve customer satisfaction and product quality through the implementation of: Six Sigma methodology Lean manufacturing TQM methodology Advanced product quality planning (APQP) Feasibility studies Kaizen events
Aircraft Engines Require High Temperature Ratings
01/15/06
1-3
www.parkerseals.com
Introduction
FlexiLip and FlexiCase seals are often used on motors and compressors and other components with high speed rotary shafts due to their ability to resist wear even while pressurized.
FlexiSeal profiles are often used when predictably low friction is critical and especially when parts must have low breakaway friction after long periods of static service.
Motors Require Wear Resistance
Control Valves Require Low Friction
01/15/06
1-4
www.parkerseals.com
Engineering
Engineering Topics
Testing and Validation, see Page 2-2 Hardware Configurations/Installation, see Page 2-3 Surface Finish and Hardness, see Page 2-9 Extrusion Gaps and High Pressure, see Page 2-10 Spring Choices, see Page 2-12 Lip Shapes, see Page 2-16 Rotary Seal Considerations, see Page 2-17
Spring Load
Pressure Load
FAQs
The FlexiSeal lips and spring energizer are compressed when installed into the seal gland. The resilient spring responds with constant force, pushing out the sealing lips, creating a gas tight seal against the sealing surfaces. As pressure is introduced in the system the seal expands increasing the sealing force beyond that provided by the spring and jacket material. In dynamic applications, the spring expands, compensating for seal wear while continuing to provide load. In conditions that see thermal cycling, the spring system continues to energize the seal lips without taking a compression set or becoming too soft or hard, as an elastomer can. The flexible spring allows for a wide tolerance range that can help overcome hardware misalignment and eccentricity, without causing excess friction or the inability to seal. Three different FlexiSeal spring designs are available that provide individual attributes for each application. See Page 2-12 for more information on spring types.
Q: A:
How does the FlexiSeal work?
FlexiSeal Design Function
Q:
How do I choose the right profile for my application?
A : Parkers PTFE product line includes both standard designs for the most common applications and custom designs that our engineers can help you develop.
For the long term, we suggest that you familiarize yourself with the design elements in this Engineering section that are critical when choosing a FlexiSeal, FlexiLip or FlexiCase seal. For quick reference and ease of sorting through the many standard designs, we have provided simple decision trees and placed them throughout this design guide. The master decision tree is located on Page 4-2 and will help you select which product family best suits your application and will send you off to the right section and subsequent decision tree to help you find the answers you need. If it becomes apparent that you need a custom design to meet your unique needs, or if you just want us to confirm the standard seal choice youve made, please contact Parker's PTFE Engineering team at 801-972-3000.
Spring Load
01/15/06
2-1
www.parkerseals.com
Engineering Testing and Validation

EPS Division uses Non-linear Finite Element Analysis (FEA) for design optimization during its product design development cycle. Utilizing FEA streamlines the prototyping phase of seal development by improving performance predictability, which cost-effectively accelerates speed to market. Parkers core-competencies using FEA simulation include:
Design
Determining friction effects and sealability. Analyzing the contact pressure profile to better understand seal contact behavior under pressure and temperature. Analyzing material extrusion, friction build-up and slipping effects on the seal surface at higher temperatures and pressures. Accurate prediction of seal failure modes by analyzing fatigue and plastic strain relaxation. Developing force vs. deflection plots for axial and radial sealing capabilities.
Analysis
Understanding the principal strain regions associated with the design. FEA results are often validated using real-time mechanical product testing. EPS Division has a sophisticated mechanical testing lab with several breakthrough advanced technologies. Product validation testing is carried out in accordance with ASTM specifications, Society of Automotive Engineers, military standards and aerospace standards. In addition our material development lab is equipped to carry out testing for material characterization such as Fourier Transform Infrared (FTIR) spectrophotometer, thermal conductivity, Tribometer-PTFE wear testing, differential scanning calorimeter (DSC), deformation under load, etc.
Manufacturing
For PTFE seal design assistance contact Parkers PTFE Engineering team at 801-972-3000.
Final Product
01/15/06
2-2
www.parkerseals.com
Engineering Gland Designs and Installation

Two-Piece Glands
Parker FlexiSeals are rigid in comparison to elastomer seals such as O-rings and U-cups. They can be damaged if stretched or compressed beyond their material limitations. It is recommended that a two-piece, split gland design be utilized whenever possible. This allows easy installation or removal of the FlexiSeal without the need for additional tools, and will greatly reduce the risk of damage to the seal. Lead-in chamfers that are blended and very smooth are necessary to prevent damage to the seal during installation. Full surface finish recommendations are described on Page 2-9.
Two-Piece Rod and Piston Glands
Two-Piece Gland Installation

Heel First Seal Installation When installing the FlexiSeal with the heel or non-pressure side first, the lead-in chamfers may be smaller than when the seal must go in lips first. The FlexiSeal is designed with a slight clearance at the heel, and is also chamfered. If lead-in chamfer angles cannot be made, a full polished radius may also be used. Both designs must be very smooth and free from sharp edges that can damage the seal.
Note: Sometimes a combination of heel first and lip first installation is required. When this occurs, match the appropriate table with the demands made on the chamfer.
R 0.015 Max.
C 20
B
E 20
Rod
A
C C
E 20
Table 2-1. Heel First Recommended Lead-In Chamfer

Cross-Section Size Nominal P/N Callout 1/16 062 3/32 093 1/8 125 3/16 187 1/4 250 C Min. 0.020 0.030 0.030 0.040 0.050
Piston
B
20 G C
R 0.015 Max.
Figure 2-1. Two-Piece Gland Heel First Installation

01/15/06
Note: Complete gland dimensions are provided in Tabs 5 9.
2-3
www.parkerseals.com
Engineering
Lips First Seal Installation When installing the FlexiSeal with the lips or pressure-side first, the lead-in chamfers need to be longer than when the seal goes in heel first. The FlexiSeal is designed with pre-load interference on the lips that require additional clearance to prevent damage during installation. A stepped retention plate is required to provide a flat backed surface for the seal and to prevent extrusion into the lead-in angles. All chamfers must be very smooth and free from sharp edges that can damage the seal. If the necessary angles and retention plate cannot be accomplished, installation tools will be required. Table 2-2. Lips First Recommended Lead-In Chamfer
Cross-Section Size Nominal P/N Callout 1/16 3/32 1/8 3/16 1/4 062 093 125 187 250 C Min. 0.050 0.070 0.090 0.110 0.140
R 0.015 Max.
R 0.015 Max.
C
20
B
E 20
Rod
A
C
C
20 E
Piston
B
20 G C
Figure 2-2. Two-Piece Gland Lips First Installation
Note: Complete gland dimensions are provided in Tabs 5 9.
Two-Piece Flanged Glands

The flanged design can be used in either static, rotary or reciprocating applications and is designed to be dynamic only on the ID. It excels in rotary applications because the flange can be clamped axially to prevent the seal from rotating with the shaft. This extra stability allows the flanged design to hold more pressure at higher surface speeds. The gland must be made in two pieces for installation purposes and could be lips-first or heel-first. Use Table 2-1 or Table 2-2 for the C1 chamfer commensurate with the direction of shaft insertion. Complete flanged gland dimensions are provided starting on Page 7-19.
R 0.015 Max.
40
C1 20
Figure 2-3. Two-Piece Flanged Gland

01/15/06
2-4
www.parkerseals.com
Engineering
Step Cut Glands
An alternative to the two-piece gland is the step cut design. This solid one-piece configuration has a reduced wall on the pressure side of the groove. This allows the seal to snap into the groove without the need for a separate retainer or installation tools. The step is designed to hold the seal in the groove during final assembly and under dynamic conditions such as low pressure return strokes in reciprocating applications. In pressurized conditions, the FlexiSeal is naturally held into the back of the groove. The step cut gland can be utilized for both rod and piston seals. We recommend using a FlexiSeal with a scraper lip on the static surface to provide a more positive snap-tight fit. See profile offerings in Tab 4 for available options. Complete dimensions for this design are supplied in Tab 5.
Incorrect Installation
Step Cut Glands
Table 2-3. Nominal Cross-Sections

Cross-Section Size P/N Nominal Callout 1/16 062 3/32 093 1/8 125 3/16 187 1/4 250
R 0.015 Max.
C1 Min. 0.035 0.050 0.065 0.080 0.095
Step Cut Gland Installation

The step cut gland can only be used when the seal sees pressure from the open or spring side of the seal. This requires the seal to be installed heel or non-pressure side first, snapping the seal lips behind the retention step. After installing the seal into the groove, the assembly can be pushed into a piston bore, or over a rod.
*Dimensions for lead-in chamfer C2 are supplied for both heel first or lips first final assembly into the bore or over the rod. Note: Complete gland dimensions are provided in Tabs 5 9.
C2 Min. Heel Lips First* First* 0.020 0.050 0.030 0.070 0.030 0.090 0.040 0.110 0.050 0.140
D 0.007 / 0.010 0.010 / 0.015 0.015 / 0.020 0.020 / 0.025 0.025 / 0.030
20
B
E
C1
Rod
20
C2 E C1
A
C2
Piston
20
B
20
G R 0.015 Max.
Figure 2-4. Step Cut Gland Installation

01/15/06
2-5
www.parkerseals.com
Engineering
Alternative Glands
For heel first installation with a snap ring retainer, the snap ring groove is set into a reduced diameter to ensure that the seal does not pass over the edges. This design can be used for both rod and piston seals. For lips first installation with a support ring and snap ring retainer, the snap-ring groove is at a reduced diameter to prevent damage to the seal. The support ring must meet clearance gap recommendations as outlined in this guide. Load ratings for snap rings must be considered to prevent fatigue or failure.
Caution: It is the responsibility of the designer to test any alternate gland designs and/or components used to ensure that they meet all required operating conditions of their specific application.
Heel First with Snap Ring
Lips First with Support Ring and Snap Ring
Figure 2-5. Alternative Installations
Closed Glands
The least desirable gland design for the FlexiSeal is the closed gland design. The seal cross-section, diameter and material are all factors that determine whether the FlexiSeal can be stretched into a solid piston groove or compressed into a rod seal housing. FlexiSeals are more easily stretched into piston grooves than compressed into rod seal housings. Table 2-4 is a guide for rod seal minimum diameters that can be used in solid grooves utilizing installation and re-sizing tools. Table 2-5 is for minimum piston seal diameters.
Table 2-4. Rod Seals Suitable for Solid Grooves

Cross-Section Size Nominal 1/16 3/32 1/8 3/16 1/4 P/N Callout 062 093 125 187 250 Minimum Rod Diameter V C H Series Series Series 1.500 1.000 1.250 2.500 2.000 2.250 6.000 5.000 5.500 11.000 10.000 10.500 16.000 14.000 15.000
Table 2-5. Piston Seals Suitable for Solid Grooves

Cross-Section Size Nominal 1/16 3/32 1/8 3/16 1/4 P/N Callout 062 093 125 187 250 V Series 1.250 1.750 2.500 4.000 6.000 Minimum Bore Diameter C Series 0.750 1.000 2.000 3.000 5.000 H Series 1.000 1.500 2.250 3.500 5.500
Closed Glands 01/15/06
2-6
www.parkerseals.com
Engineering
Closed Gland Installation
2
Closed Gland
Piston Seal Installation in Solid Gland A stretching guide ramp and resizing tool should be fabricated to assist in installing the FlexiSeal into a fully closed cavity. Refer to these drawings for design specifications.
16 (0.4) 0.015 in. Max. (0.38 mm) 15
15
16 (0.4)
Guide Ramp Min. Seal ID + 0.100 in. (2.54 mm) Max. Component OD + 0.003 in. (0.08 mm)
Resizing Tool Max. Component OD + 2 x Seal Cross-Section
Figure 2-6. Stretching Guide Ramp and Resizing Tool STEP 1: Place the seal on the guide ramp. Preheating the seal to as much as 300 F (150 C) in either oil, air or water will soften the seal and aid in stretching and installing the seal. Care must be taken to prevent burns when using this option.
Seal ID
Component OD
Figure 2-7. Place on Guide Ramp STEP 2: Push the seal over the guide ramp and into the groove.
Figure 2-8. Push Seal STEP 3: Slide the resizing tool over the seal to compress the seal to its original diameter.
Figure 2-9. Compress Seal
01/15/06
2-7
www.parkerseals.com
Engineering
Rod Seal Installation in Solid Gland STEP 1: Install the seal with the blunt end of the pusher tool.
STEP 2: Resize the seal with the rounded end of the tool.
One-Piece Face Seal Glands

Face seal glands can be one-piece machined grooves because seal installation does not require excessive stretching or compressing. The FlexiSeal is designed to have a clearance or slight interference fit on the heel of the seal (non-pressure side) so it will press easily into the groove. More information is available in Tab 6.
Rod Install Resize
Figure 2-10. Rod Seal Installation in Solid Gland
Glands with Special Requirements

The metal case in a FlexiCase seal is designed to secure a firm press-fit into a counterbore. This fit can always be reinforced by a secondary retainer or snap ring for higher pressure applications. Since the FlexiLip does not have a metal can for bore retention, it is more succeptable to axial movement due to pressure forces. For this reason, Parker recommends using a retainer as shown in applications where pressure could push the seal out of the gland. The FlexiLips metal band option allows it to retain its diameter during temperature cycles, but does not act to press-fit the seal into place like a FlexiCase. More gland design information can be found in the Engineering sections of Tabs 8 and 9.
FlexiCase in Gland
FlexiLip in Gland
01/15/06
2-8
www.parkerseals.com
Engineering Surface Finish and Hardness

Mating Surface Finish
Proper surface finish of the seal gland is critical to ensure positive sealing, and achieve the longest seal life possible in dynamic applications. Mating surfaces that are too rough can create leak paths and can be very abrasive to the seal. Unlike elastomer contact seals, PTFE-based FlexiSeals can run on very smooth surfaces with or without lubrication. Due to the toughness and low coefficient of friction of PTFE, FlexiSeals slip over the high points of the mating surface and resist abrasion. To maximize seal performance, the recommendations for surface roughness in Table 2-6 should be followed. Dynamic surfaces with relatively rough finishes will result in higher wear rates which decrease the seal life and may compromise performance.
Relative Wear, Friction and Leakage Rate 3.0
4.0
2
2.0
1.0
0 0 4 8 12 14 16 20 24 28 Dynamic Surface Finish Ra inch
Figure 2-11. Dynamic Surface Finish vs. Wear Table 2-6. Surface Roughness, Ra
Media Being Sealed Cryogenics Helium Gas Hydrogen Gas Freon Air Nitrogen Gas Argon Natural Gas Fuel (Aircraft and Automotive) Water Hydraulic Oil Crude Oil Sealants Dynamic Surfaces inch 04 max. 06 max. m 0.1 max.0 0.15 max. Static Surfaces inch 08 max. 12 max. m 0.2 max. 0.3 max.
08 max.
0.2 max.
16 max.
0.4 max.
12 max.
0.3 max.
32 max.
0.8 max.
Mating Surface Hardness

Most dynamic applications require a hard running surface on the dynamic portion of the hardware. The harder surface allows the use of higher reinforced seal materials that will increase both the seal and hardware life. Softer running surfaces must use lower wear resistant seal materials that will not damage the hardware, but normally yield shorter seal life. A balance between seal material and dynamic surface hardness must be met to ensure that the seal remains the sacrificial component.
01/15/07
2-9
www.parkerseals.com
Engineering
When the dynamic surface hardness is below 45 Rc, most seal materials will polish the running surface of the hardware and the seal. This initial break-in period will cause seal wear to taper off over a period of time depending on the seal material, surface finish, pressure and velocity of the application. When hardness exceeds 45 Rc, the initial surface finish is very important since the surface is much harder to polish and the time to achieve break-in is longer. Surface hardness above 65 Rc will resist polishing and therefore the initial surface finish is more critical to seal life. The hardness of the dynamic hardware surface affects the wear rate of the seal. Additionally, some seal jacket materials are abrasive and will wear softer metal shafts or dynamic components. In general, higher surface hardness results in better overall seal and hardware performance. The ideal hardness of the dynamic surfaces of the hardware is 50 to 60 Rockwell C. The extended heel FlexiSeal design prevents seal extrusion by increasing the material in the heel of the seal, effectively increasing its overall length. This extra material acts as a built-in back-up ring and fills the gap before damage is done to the rest of the seal. In applications that have excessive clearance gaps and/or pressures above 10,000 psi, it may be necessary to use separate back-up device(s) or special seal designs to reduce the seals exposure to the gap. See Page 5-10 for information on how to designate an extended heel in the part number. Also, refer to Figure 2-13 for a detailed look at how pressure rating is affected by several parameters. The pressure ratings for FlexiLip and FlexiCase seals are profile specific. In other words, each profile has been given a specific pressure rating according to its own physical limitations as shown on Pages 8-9 and 9-8.
Pressure Extrusion Gap
Extrusion Gap V Series Standard 3000 psi C Series H Series
High Pressure Seals Battling Extrusion Gaps

Pressure capabilities are a function of temperature, seal material, extrusion gaps and seal design.The standard FlexiSeal is rated to 3000 psi when used in glands conforming to the dimensions supplied in this guide, using materials that meet the temperature requirements of the application. Extended heel radial FlexiSeals are available which increase the pressure rating to 10,000 psi under the same conditions.
Extended Heel 10,000 psi
Figure 2-12. High Pressure Seals
Excessive Extrusion Gap
Material Extrusion
Standard FlexiSeal
Extended Heel FlexiSeal
01/15/06
2-10
www.parkerseals.com
Engineering
Material Pressure/Extrusion Resistance Rating (See Table 3-1)
1, 2, 3, 4, 5
Consult Factory 8000 10000
6000
7000
Class D Pressure, psi 4000 6000 Class C Class B 2000 4000 Class A 0 2000 062 1/16 093 3/32 125 1/8 Seal Cross-Section Size 187 3/16 250 1/4 -400 -200
-400 -200
-200 0 0
0 200 200
200 400 400
400 600 600
Temperature, F
Figure 2-13. Extrusion Gap Class Table 2-7. Maximum Extrusion Gap
Heel Type Standard Cross-Section Class A 0.008" Class B 0.006" Class C 0.004" Class D 0.002"
Extended
0.012"
0.009"
0.006"
0.004"
01/15/06
2-11
www.parkerseals.com
Engineering
load is increased, the lips seal tighter, with friction and wear increasing proportionately. The springs deflection range affects the seals ability to compensate for variations in gland tolerances and for normal seal wear. Each spring size has a specific deflection range. The available deflection increases as the seal and spring cross-section increases; this could be a deciding factor in selecting one cross-section over another. Springs with a wide deflection range should be used when sealing surfaces are not concentric (see Page 2-19).
V Series Cantilever Spring Loading Provides Positive Sealing Contact Spring-Loaded, Positive Contact
Not Loaded, Poor Contact
Figure 2-14. Spring Loading

C Series Canted-Coil H Series C Series
V Series Spring Load H Series Helical
Spring Compression
Spring Designs
The FlexiSeal uses one of three different spring types to energize the jacket. The two elements to consider when selecting a spring design are its load value and its deflection range. The springs load affects the sealing ability, friction and wear rate. As the spring
Figure 2-15. FlexiSeal Spring Energizers Figure 2-15 shows a relative comparison of load vs. deflection curves for the three spring types. The signifies the typical deflection when the seal is installed. The hatch marks indicate the deflection range through which the seal will function properly. Notice that H Series has a much smaller deflection range than both the V and the C Series.
01/15/06
2-12
www.parkerseals.com
Engineering
Cantilever Springs V Series
The FlexiSeal Cantilever spring is made from flat metal strip stock of 300 Series stainless steel or Elgiloy as an option. The strip stock is punched or chemically etched into a serpentine pattern and formed into a rounded V shape. It is available in either a light or medium load spring. The medium spring is suitable in most applications, but the light load spring can be used if having low friction is more important than sealability. The medium spring load deflection curve is depicted in Figure 2-15 on Page 2-12. The cantilever spring is intended for dynamic applications involving rotary or reciprocating motion. It can also be used in static conditions when there is need for a higher deflection spring due to wide gland tolerance, excessive expansion and contraction, or lift-off due to high pressure. The long beam leg design puts the spring load out at the leading edge of the seal, creating the best load location for the FlexiSeal to act as a scraper when the optional scraper lip is selected. The geometry of the V Series cantilever spring provides flexibility by utilizing individual tabs, separated by small gaps. This shape allows the spring to flex into radial and axial seal designs. The spring tabs can overlap on the ID and spread apart on the OD when the cross-section is too large for the diameter. Table 2-8 provides the minimum diameters for V Series springs for rod and piston seals, as well as internal and external pressure face seals. For diameters smaller than those listed, C or H Series spring designs are recommended.
V Series / Cantilever
2
External Pressure (Seal ID) 0.500 0.875 1.125 2.000 3.000
Table 2-8. Minimum Diameters for V Series

Nominal CrossSection 1/16 3/32 1/8 3/16 1/4 Rod Shaft Dia. 0.125 0.187 0.375 0.875 1.625 Piston Bore Dia. 0.250 0.375 0.625 1.250 2.125 Internal Pressure (Seal OD) 0.750 1.250 1.750 2.250 3.500
Features V-shaped spring with moderate load vs. deflection Standard inch/fractional and MIL-G-5514 sizes Standard 300 series stainless steel springs NACE compliant Elgiloy springs available in medium spring load, -450 to 600 F Scraper lip designs for abrasive medias Available as external & internal pressure face seals Recommended Applications Reciprocating rods & pistons Rotary shafts <1000 sfpm Wide tolerance and misaligned glands (static) Abrasive medias (when scraper lip is designated) Dynamic applications above 450 F
Load Point
Spring Force
Load Point
Figure 2-16. Installed State
01/15/06
2-13
www.parkerseals.com
Engineering
Canted-Coil Springs C Series
The FlexiSeal C Series spring is made from round wire that is coiled and formed into a canted or slanted shape. The result is a radial compression spring with a very flat load versus deflection curve as illustrated in Figure 2-15 on Page 2-12. Both 302 stainless steel and Hastelloy C-276 are available as standards in three different spring loads. The canted-coil spring is intended for dynamic reciprocating and rotary applications. It is also used in static applications when wide gland tolerance or misalignment is present. The flat load curve of this design makes it an ideal choice for friction sensitive applications. The C Series spring can be fit into small seal diameters without overlapping the individual spring coils. Because the ID coils tend to butt up to each other, the spring has very small gaps providing maximum spring contact. This geometry is well suited for dynamic rod seal applications less than 1/2" diameter. The C Series spring is available in Light, Medium and Heavy load ranges. Light: Applications that require extremely low break-out and running friction when sealing ability is less important than friction. Medium: General application. Medium friction but reliable sealing capability. Normally the starting point for new applications. Balance functions of friction, sealing ability and dynamic wear. Heavy: Applications where optimum resilience is required due to hardware separation. Accelerated seal material wear in dynamic applications. Used when primary objective is sealing and friction and/or wear is secondary.
C Series / Canted-Coil
The C Series spring produces compression load near the center of the seal. The standard beveled lip seal geometry puts the point of contact slightly in front, forcing the spring back into the spring cavity. The lip design provides concentrated unit load at the sealing interface, and allows lubrication to the dynamic lip, increasing the wear life. Because of this geometry, the C Series is not the best choice for abrasive medias. For abrasive conditions the FlexiSeal V Series is recommended. See Page 2-13 for details. Features Canted coil spring with flat load vs. deflections Light, medium and heavy load springs standard Standard inch/fractional and MIL-G-5514 sizes Standard 302 series stainless steel springs Hastelloy springs available Available as external & internal pressure face seals Recommended Applications Friction sensitive applications Reciprocating rods & pistons Rotary shafts <1000 sfpm Wide tolerance and misaligned glands Dynamic applications above 450 F Diameters <1/2" and crosssections <3/32"
Load Point Spring Force Load Point
01/15/06
2-14
www.parkerseals.com
Engineering
Helical Springs H Series
The H Series spring is made from flat ribbon metal strip stock that is formed into a helix shape. The standard material is 17/7 PH stainless steel, and Elgiloy is offered as an option. The finished spring produces a very high load versus deflection curve as shown in Figure 2-15 on Page 2-12. The helical spring design is intended for static applications due to the high unit load. It can be used in very slow or infrequent dynamic conditions when friction and wear are secondary concerns to positive sealing. The H series spring produces evenly distributed load across each individual band, with very small gaps between the coils. This tight spacing provides near continuous load, reducing potential leak paths. This, combined with the high unit load, makes the H series well-suited for vacuum and cryogenic applications or when pressure is too low to energize the seal. The load provided by the H Series spring is directly through its center line. The lip design of the FBN-H profile is a full radius at the sealing interface, providing maximum load to the contact points to effect a tight seal. The spring is welded at the ends. When the seal is compressed into the hardware, the spring cavity is designed to allow axial spring growth. The relatively small deflection range of the H Series spring prevents it from being used in applications having wide gland tolerances, eccentricity or misalignment. The V or C Series FlexiSeal should be considered for these conditions.
H Series / Helical
2
Features Helical wound ribbon spring with high load vs. deflection Standard inch/fractional and MIL-G-5514 sizes Standard 17/7 PH stainless steel springs NACE compliant Elgiloy springs available Available as external & internal pressure face seals Recommended Applications Static rods & pistons Static internal & external pressure face seal applications Slow dynamic applications <200 sfpm Vacuum sealing Applications where sealing ability is critical
Load Point
Spring Force
Load Point
01/15/06
2-15
www.parkerseals.com
Engineering Lip Shapes

Chamfered Lips
The most common lip shape is the chamfered or back-beveled design and is available with the V and C Series spring types. This design allows for ease of installation and permits lubrication to nest under the lip and feed through in reciprocating dynamic applications. The result is a microscopic film of lubrication that increases seal and hardware service life. Since the footprint (contact point) of a chamfered lip is a single point, all of the sealing force is concentrated on that point, yielding the highest sealability and lowest friction.
Abrasive Media Trapped by Lip
Abrasive Contamination Chamfered Lip
FBC-V
FBN-C
Figure 2-19. Chamfered Lips
Scraper Lips
Applications often involve medias with abrasive particles that can get caught between the seal lip and the mating hardware. This increases wear to both the seal and the mating surface. To prevent particles from accumulating, the scraper lip design is available with all three spring types. The scraper lip contact point is positioned directly over the load point of the spring in each design for maximum scraping action. The scraper lip can be positioned on the ID, OD or both. The scraper lip also stays in place better in a stepped gland where the step is not very large.
Abrasive Media Scraped by Lip
Scraper Lip
Scraper ID
Scraper OD
Dual Scraper
Figure 2-20. Scraper Lips

01/15/06
2-16
www.parkerseals.com
Engineering
Beaded Lips
The beaded shape contacts the surface in much the same way as an O-ring, and is available with the V and H Series spring types. Similar to the chamfered lip, it is easy to install and helps to lubricate the reciprocating sealing surface. In fact, the beaded lip yields a film of oil that is slightly thicker than that of a chamfered lip, making it advantageous for applications with rapid reciprocating motion.
Rotary Seal Considerations

For all rotary seals FlexiSeal Rotary, FlexiLip and FlexiCase the designer must consider: pressure and shaft velocity lubrication shaft misalignment and runout shaft hardness and surface finish advantages of different lip shapes shaft lead temperature
Pressure & Shaft Velocity

Unlike reciprocating applications, seals ride on a rotating shaft in only one small area where dynamic forces and energy are concentrated. In fact, much of the energy from the shaft is dissipated at the contact point in the form of frictional heat and wear, both of which are detrimental to seal life. This effect is accentuated by increasing the shaft speed or by increasing the perpendicular force holding the lip against the shaft. Shaft speed can be measured in surface feet per minute and the lip force can be approximated by measuring the differential pressure across the seal in psi. Shaft velocity in surface feet per minute is calculated as follows:
Shaft Surface Velocity = Diameter (inches) (in sfpm)
FBK-V
FBN-H
Figure 2-21. Beaded Lips
x 0.262 x Shaft RPM
One way to estimate the exposure to these risks is to calculate the PV-value by multiplying the pressure held by the seal (P in psi) by the surface velocity of the shaft (V in surface feet per minute). The product of this multiplication provides the designer with a guide to aid in the choice of seal profile and material. Let us run through an example: Given: Pressure = 45 psi Shaft diameter = 1.25" Shaft rotational speed = 350 RPMs
Shaft Surface = Diameter Velocity = 115 sfpm Shaft x 0.262 x Rotational Speed = 1.25" x 350 RPMs x 0.262
PV-value = Pressure x Surface Velocity = 45 psi x 115 sfpm = 5175 ft. lb./in2 min.
01/15/06
2-17
www.parkerseals.com
Engineering
Pressure Velocity Curves
2
10,000 Assumptions Optimal seal profile choice Ambient temperature Low shaft runout Generally non-extreme conditions
F le
Un lu
Pressure in psi
xiS eal PV Lim it
bri c a ted
Rapid Wear Zone
i mit PV L
500
Lubricated PV Limit
FlexiLip & FlexiCase PV Limit
1000 Velocity in surface feet per minute
5000
Figure 2-22. Pressure Velocity Chart The PV graph in Figure 2-22 applies to unlubricated rotary applications using a stable rotary seal utilizing a jacket material with a 4 or 5 wear resistance rating. As a rule of thumb, a PTFE rotary seal can be used in unlubricated applications with a PV of up to 150,000. This information is intended to be used only as a guide since there are many other factors, such as sealing media, hardware material and surface finish, which affect the wear life of the seal. Remember, anything that can be done to decrease the heat generation between the lip and the shaft will likely increase seal life. In cases where the media being sealed is a lubricant, these seals can operate continuously at PV levels two to three times higher as shown in Figure 2-22. present in rotary applications. A film of lubricant between the seal lip and the shaft reduces seal wear and frictional heat generation, makes higher surface speeds possible, and helps prevent the seal from wearing a groove in the shaft. When the lubricant splashes or flows past the seal area, it acts as a coolant, prolonging seal life.
Rotary Product Choice

While the black and white curves above attempt to draw the line between what can and cannot be done, they do not show which profiles work best within the limits of feasibility. The blue and brown curves above show which product lines work better with regard to pressure and surface speed assuming there is no lubrication. Rotary FlexiSeals can be used when pressures are high and speeds are low, while FlexiLip and FlexiCase profiles lend themselves more to applications with high surface speeds and low pressure.
01/15/07
Lubrication
While FlexiSeals made of PTFE have a natural lubricity and can be used in unlubricated applications, it is always better to have lubrication
2-18
www.parkerseals.com
Engineering
Shaft Misalignment and Runout
Applications with rotating shafts come with their own set of common problems. Among these are those associated with the shaft not being aligned properly with the surrounding hardware. Misalignment most commonly manifests itself as Eccentricity and Runout. Every shaft has some degree of both as described in Figure 2-23. Eccentricity of a rotating shaft creates two problems. One is that it forces the seal lip to follow a shaft that is not centered in the bore, wearing the lip more on one side. The second potential problem is that it enlarges the extrusion gap on one side, which could be detrimental if high pressure is involved. Please refer to Figure 2-23 for a graphic representation. Shaft Runout is when the shaft is spinning on an axis of rotation that is offset from the geometric center of the shaft at the point of seal lip contact. Runout can be caused by a bent shaft or by whirling deflection while spinning. The seal must be sufficiently compliant to maintain contact with the shaft despite being compressed and extended each revolution. It follows that shaft runout becomes more of a problem at high speeds.
inch 0.011 0.010 0.009 0.008 0.007 0.006 0.005 0.004 0.003 Shaft Centerline Seal Housing Cavity Diameter (Bore) 0.002 0.001 inch 1/16 3/32 1/8 3/16 FlexiSeal Cross-Section 1/4 2 1
Bore Centerline
1 Maximum Eccentricity with No Runout 2 Maximum Shaft Runout (less than 500 RPM) with No Eccentricity ECCENTRICITY With eccentricity, only static radial deflection is imposed on the seal. MISALIGNMENT
Figure 2-24. FlexiSeal Eccentricity and Runout Limits All rotating shafts have eccentricity and runout to some degree. The risk of failure increases significantly if a system has a considerable amount of both. Figure 2-24 shows the acceptable maximum for these parameters for all rotary FlexiSeal profiles except the FFN-H. Figure 2-25 shows the limits for FlexiLip and FlexiCase profiles.
Bore Centerline
Shaft Runout Envelope Shaft Centerline (Orbits around axis of rotation)
Shaft Geometric Centerline ECCENTRICITY In this case, cyclical radial deflection due to runout is superimposed on static radial deflection due to eccentricity. AXIS OF ROTATION
Shaft Axis of Rotation
Runout (inches)
SHAFT RUNOUT
0.004 0.003 0.002 0.001
High Leakage and Wear Range Assuming Shaft Speed of 1750 RPM Acceptable Range
Figure 2-23. Eccentricity and Shaft Runout

0.001 0.002 0.003 0.004 0.005 0.006 Eccentricity (inches)
Figure 2-25. FlexiLip and FlexiCase Eccentricity and Runout Limits

01/15/06
2-19
www.parkerseals.com
Engineering
Lip Shapes
FlexiSeal Rotary profiles are characterized by their lip shapes. Chamfered lips maximize sealability while minimizing friction. Scraper lips prevent particles from accumulating at the lip, which makes wash-downs more effective. Fortunately it is easy to check for the presence of machine lead on a shaft. Hang a weighted string from the shaft and measure the axial distance it moves per shaft revolution. The lead needs to be kept to less than 0.05 degrees. Please refer to RMA Handbook OS-1 for measurement guidelines.
Shaft Machine Lead

When a shaft is turned to size, a continuous spiral groove is imparted on the shaft as the cutting bit traverses the shaft. If not removed by plunged grinding, the groove will act as an auger when the shaft rotates and will either pump oil under the seal lip or contaminates into the bearing housing, depending on the direction of the shaft rotation. Figure 2-26. String Test for Shaft Lead
01/15/06
2-20
www.parkerseals.com
Materials
Parker EPS has over 300 PTFE compounds and polymeric materials for the manufacture of FlexiSeal, FlexiLip and FlexiCase seals. Our material offering includes non-filled PTFE, standard and specialty filled PTFE compounds, TFM blends, UHMW polyethylene and thermoplastic elastomers. Parker can meet your seal material requirements for PTFE sealing in most all environmental and operating conditions. If your application demands unique material specification, our in-house chemists have the expertise and capability to work with you in specifying and validating optimal materials to meet your requirements.
Advantages of PTFE as a Jacket Material

Low Friction
The low coefficient of friction (.06) of PTFE material results from low interfacial forces between its surface and other materials that it may come in contact with. This behavior of PTFE material reduces any possibility of stick-slip effects in dynamic sealing applications.
Wide Temperature Range (-450 to 600 F)

PTFEs high melting point and morphological characteristics allow components made from the resin to be used continuously at service temperatures to 600 F. Above this temperature the components physical properties tend to decrease, causing heat-aging and material degradation. The polymer itself might remain unaffected, if the temperature is insufficient for thermal degradation. For sealing cryogenic fluids down to -450 F, special designs using PTFE and other fluoropolymers are available.
The intrapolymer chain bond strengths of PTFE compounds preclude reaction with most chemicals, thereby making them chemically inert at elevated temperatures and pressures with virtually all industrial chemicals and solvents. For a comparison of compatibility ratings for PTFE compound with other plastics and elastomers, refer to the chemical compatibility charts in Appendix C.
Dry Running Capability

Due to the strength of the carbon-fluorine and carboncarbon single bonds, PTFE compounds have high thermal stability and self-lubricating capabilities, offering continuous dry running ability in dynamic sealing applications.
Temperature Cycling
Unlike most elastomers, PTFE compounds have the unique ability to resist material degradation, heat-aging and alteration in physical properties during temperature cycling.
High Surface Speeds

The low friction characteristics and resistance to heat of PTFE makes it the ideal candidate for high surface speed applications. PTFE compounds perform exceptionally well in high surface speed sealing applications where O-rings or U-cups made of elastomers fail due to heat generation.
01/15/06
3-1
www.parkerseals.com
Materials Enhancing Performance of PTFE with Fillers

An important requirement for any potential PTFE filler is that it must be able to withstand the sintering temperatures of PTFE. Sintering involves exposure to temperatures close to 700 F for several hours. 0601 Aromatic Polyester Filled Aromatic polyester is excellent for high temperatures and has excellent wear resistance against soft, dynamic surfaces. Not recommended for sealing applications involving steam. 0204 Molybdenum Disulfide and Fiberglass Filled Molybdenum disulfide increases the hardness of the seal surface while decreasing friction. It is normally used in small proportions combined with other fillers such as glass. MoS2 is also inert towards most chemicals. 0203 Fiberglass Filled A number of other fillers are used in combination with PTFE. For best results for your sealing applications, please contact the EPS Division Application Engineering team at (801) 972-3000. 0102 Modified Virgin PTFE Same basic properties as virgin, but with increased wear and creep resistance and lower gas permeability. 0307 Carbon-Graphite Filled Carbon reduces creep, increases hardness and elevates thermal conductivity of PTFE. Carbongraphite compounds have good wear resistance and perform well in non-lubricated applications. 0502 Carbon Fiber Filled Carbon fiber lowers creep, increases flex and compressive modulus and raises hardness. Coefficient of thermal expansion is lowered and thermal conductivity is higher for compounds of carbon fiber filled PTFE. Ideal for automotive applications in shock absorbers and water pumps. 0120 Mineral Filled Mineral is ideal for improved upper temperatures and offers low abrasion to soft surfaces. PTFE with this filler can easily be qualified to FDA and other food-grade specifications like 0127 and 0128. 0405 Stainless Steel Filled Although stainless steel filler is very abrasive, this compound has excellent extrusion and high temperature resistance in static and slow dynamic applications. 0615 Proprietary Low Wear PTFE This proprietary filled PTFE offers low wear and friction properties, used in general applications where long life is required. Not recommended for applications with abrasive media.
01/15/06
Glass fiber has a positive impact on creep performance of PTFE. It also adds wear resistance and offers good compression strength. 0301 Graphite Filled Since graphite is often used as a lubricant, it does not significantly increase the coefficient of friction of PTFE when used as a filler. The low friction allows the compound to be used when both shaft speed and pressure are high. Graphite also is chemically inert which enables its use in corrosive medias.
3-2
www.parkerseals.com
Materials Features of Other Machinable Plastics

UHMW Polyethylene
Temperature Range -360 to 180 F Excellent wear and abrasive resistance Good lubricity in water Excellent sealing of light gases at low pressures Excellent high pressure extrusion resistance Moderate abrasion to soft hardware Excellent wear resistance in reciprocating applications
16,000 14,000 12,000 10,000 8,000 6,000 4,000 2,000
Tensile Strength (psi)
Hytrel* Thermoplastic (TPE) Elastomer

Temperature Range -80 to 275 F Excellent wear and extrusion resistance Excellent sealing of light gases at low pressures Excellent high pressure extrusion resistance Low abrasion to soft dynamic hardware material Minimum dynamic surface hardness 25 Rc Excellent wear resistance in reciprocating applications Good wear resistance in rotary applications
300 500 400 600
0
Virgin UHMW Hytrel PEEK PTFE
Figure 3-1. Ultimate Tensile Strength (psi)

Elongation (%)
Polychlorotriflouroethylene (PCTFE)
Excellent electrical properties Stable for continuous usage until 400 F Low creep at room temperature
200 100 0
Virgin UHMW Hytrel PEEK PTFE
Polyetheretherketone (PEEK)
Chemically inert Very strong and rigid Temperature range -80 to 500 F Excellent abrasion resistance
*Hytrel is a registered trademark of DuPont.
Figure 3-2. Ultimate Elongation (%)
01/15/06
3-3
www.parkerseals.com
Materials
Table 3-1. FlexiSeal Materials Typical Physical Properties
Parker Material Code 0100 0102 Service Tensile Temperature Strength in Elongation Hardnessin % Shore D Range (F) psi at Break -425 to +450 -320 to +450 4575 4600 400 390 60 60
Material
Color
Typical Applications & Description
Virgin PTFE Modified PTFE
White Turquoise
Excellent for cryogenic applications. Good for gases. Lower creep, reduced permeability and good wear resistance. Excellent compressive strength and good wear resistance. Excellent for extreme conditions such as high pressure & temperature and for longer wear life on hardened dynamic surfaces. Excellent wear resistance and reduced creep. Excellent for corrosive service. Low abrasion to soft shafts. Good in unlubricated service. Good for strong alkali and hydrofluoric acid. Good in water service. Excellent low abrasion to soft surfaces & improved upper temperature performance. Excellent high temperature capabilities & excellent wear resistance. Excellent extrusion resistance at high temperatures and pressures. Excellent in gases and most hydraulic fluids. Good abrasion resistance with high wear properties.
0203 0204
Fiberglass Filled PTFE Gold Fiberglass & Moly Filled PTFE Gray
-200 to +575 -200 to +575
3480 3100
190 245
67 62
0307 0301
Carbon-Graphite Filled Black PTFE Graphite Filled PTFE Black
-360 to +575 -250 to +550
2250 3200
100 260
64 60
0502
Carbon Fiber Filled PTFE Mineral Filled PTFE
Brown
-200 to +550
3200
312
60
0120
White
-360 to +550
4070
270
65
0601
Aromatic Polyester Filled PTFE Stainless Steel Filled PTFE Hytrel* Unlubricated Thermoplastic Elastomer UHMW Polyethylene
Tan
-360 to +550
2500
200
61
0405
Gray
-300 to +600
2200
190
72
0913
Black
-80 to +275
5800
500
55
0901
Translucent High wearing plastic for use in abrasive medias. Excellent in water-based medias, but restricted chemical and heat resistance. Purple Excellent low wearing material. Kind to soft mating surfaces in the Rb range. FDA compliant materials for sanitary food and pharmaceutical processing. FDA material with an antimicrobial agent added to prevent bacterial growth.
-320 to +200
6000
325
67
0615
Proprietary Low Wear PTFE Mineral Filled PTFE FDA compliant for rotary appl. Mineral Filled PTFE Antimicrobial
-360 to +550
3470
200
63
0127
White
-360 to +550
2800
250
66
0128
White
-360 to +550
2800
250
66
*Hytrel is a registered trademark of DuPont.
01/15/07
3-4
www.parkerseals.com
Materials
High Pressure/ Permanent Chemical Wear Coefficient Extrusion Deformation of Thermal Under Load Compatibility Resistance Parker Coefficient Thermal Resistance FDA/NSF Rating Rating Material Conductivity Expansion Rating 70 F Compliant in/in/F x 10-5 Code of Friction in W/mK 2000 psi 5 = Excellent at 203 F in % 1 = Fair 0100 0102 0.05 0.10 0.05 0.10 0.30 0.29 11.0 11.0 7.0 6.9 5 5 1 2 1 2 Yes Yes
3
0203 0204 0.08 0.12 0.08 0.12 0.27 0.28 10.0 11.0 6.0 6.0 5 5 5 4 5 4 No No
0307 0301
0.08 0.11 0.07 0.09
0.35 0.39
8.0 11.0
2.5 3.5
5 5
4 4
4 3
No No
0502
0.09 0.12
0.31
13.0
1.8
No
0120
0.08 0.12
0.23
11.0
4.2
Yes
0601
0.09 0.13
0.32
9.0
5.5
No
0405
0.30 0.34
0.40
8.0
3.6
No
0913
0.18 0.30
0.16
7.2
No
0901
0.17 0.22
11.0
7.1
Yes
0615
0.09 0.12
0.30
9.0
3.2
No
0127
0.07 0.10
0.30
11.0
5.5
Yes
0128
0.07 0.10
0.30
11.0
5.3
Yes
Note: We emphasize that this tabulation should be used as a guide only. It is based primarily on laboratory and service tests, but does not take into account all variables that can be encountered in actual use. Therefore, it is always advisable to test the material under actual service conditions before specification. If this is not practical, tests should be devised that simulate service conditions as closely as possible. Parker EPS Division also offers unique material blends and recipes along with a wide variety of other PTFE filler combinations and colors to enhance seal performance in the most extreme application needs. For guidance on material selection for extreme applications, please contact an EPS Division PTFE Application Engineer at 801-972-3000.
01/15/07
3-5
www.parkerseals.com
Materials Spring Materials

Table 3-2. Spring Materials
Spring Material 300 Series Stainless Steel (Cantilever 301 SS) (Canted Coil 302 SS) 17-7PH Stainless Steel (Helical) Application General purpose spring material for most fluids up to 600 F. It is recommended to 400 F in corrosive media. 17-7PH exhibits better retention of mechanical properties at temperatures over 400 F than 300 series stainless steel. NACE approved. Recommended for applications above 500 F and is corrosion resistant in salt water or severe media. Resistant in severely corrosive or milder fluids when temperatures exceed 400 F.
Elgiloy (Cantilever and Helical) Hastelloy C276 (Canted Coil and Helical)
Table 3-3. Spring Loads Available by Cross-Section

Seal FlexiSeal V Series Spring Cross-Section Spring Load Spring Material Available S = 301 Stainless E = Elgiloy 062 Cross-Section Available 093 125 187 250
L M
4 4 4 4 4 4
4 4 4 4 4 4
4 4 4 4 4 4
4 4 4 4 4 4
4 4 4 4 4 4
FlexiSeal C Series
L M H
S = 302 Stainless H = Hastelloy S = 17-7PH Stainless E = Elgiloy
FlexiSeal H Series
L = Light M = Medium H = Heavy
01/15/06
3-6
www.parkerseals.com
Product Offering
Product Line
PTFE FlexiSeal
FlexiSeal
The FlexiSeal is a spring-energized U-cup utilizing a variety of jacket profiles, spring types and materials in Rod & Piston, Face and Rotary seal configurations. FlexiSeals are used where elastomeric seals fail to meet the temperature range, chemical resistance or friction requirements. Jacket profiles are made from PTFE and other high performance polymers. Spring types are available in corrosion-resistant metal alloys, including stainless steel, Elgiloy and Hastelloy. Standard FlexiSeals are precision machined to fit inch/fractional and MIL-G-5514 glands. Standard and custom sizes in multiple geometries are available from 1/8" to 72" diameters.
FlexiLip
FlexiLip seals are rotary seals incorporating a deflected lip seal geometry. Anti-rotational devices such as flanges and O-rings are often utilized to prevent the seal from rotating with the shaft. Standard and custom sizes are available with a wide selection of PTFE materials. FlexiLip seals are suitable for sealing corrosive and abrasive media. A wide range of geometries and materials are available, depending on specific application requirements. FlexiLip seals are often used when quantities are small (<100pc/yr) and it is difficult to justify tooling costs for a FlexiCase solution.
FlexiLip
FlexiCase
The FlexiCase seal is a metal-cased rotary lip seal suitable for applications where elastomeric lip seals fail and mechanical seals are too costly. The filled PTFE element provides greater chemical compatibility, wider temperature ranges, higher pressure capabilities, and longer life than elastomeric lip seals. FlexiCase seals: Can run in dry and abrasive media environments Are available in single, dual and triple lip designs Are designed to press fit into a counterbore
FlexiCase
01/15/06
4-1
www.parkerseals.com
Product Offering Master Decision Tree

Dont know which of the 66 standard profiles best fits your application? Just start at the left and begin answering the basic application questions in the decision tree. Follow the tree through, and it will guide you to the profile that should be the best fit for your application. The decision trees in this guide are to be used as an engineering guide only. Often several other parameters must be considered to optimize seal design. Contact Parkers PTFE Engineering Team for confirmation of your choice or further recommendations. Parker also recommends that any seal be tested in the application conditions before releasing for production.
Static Face Seals Page 6-4 Face Seal? Radial Seal? Static Radial (Rod and Piston) Page 5-4 FlexiLip Page 8-7
No Yes
Metal Can Press-Fit?
Low Friction/ Long Life? Better Sealability?
FlexiCase Page 9-7
FlexiSeal Rotary Page 7-5 FlexiLip Page 8-7

No Yes
Metal Can Press-Fit? Less than 1000? 1000 to 2500?
FlexiCase Page 9-7
Static, Intermittent Slow Dynamic
Surface Speed in sfpm? 2500 to 5000?
FlexiCase Page 9-7 FlexiCase Page 9-7 Low Friction/ Long Life?
Dynamic
Pressure in psi?
Less than 150? 150 to 750? Surface Speed in sfpm? 750 to 10k?
Better Sealability? Less than 500? 500 to 1000? FlexiSeal Rotary Page 7-5
Rotary? Reciprocating?
FlexiCase Page 9-7 FlexiSeal Rotary Page 7-5 Reciprocating Dynamic Page 5-5
01/15/06
4-2
www.parkerseals.com
Product Offering Part Number Nomenclature FlexiSeal

Table 4-1. FlexiSeal Part Number Nomenclature
English 0 5 0 2 FB S 1 2 5 0 0 5 0 0 1 7 0 S C L
Gland Cross-Section Examples: 062 = 0.062" 093 = 0.093" 125 = 0.125" 187 = 0.187" 250 = 0.250" Lip Style Designation N = Default Lip Style C = Chamfered ID & OD S = Scraper ID G = Scraper OD D = Dual Scraper K = Beaded ID & OD L = Beaded ID & Scraper OD M = Scraper ID & Beaded OD
Gland Inside Diameter (Rod or Groove Diameter) Examples: 00500 = 0.500" 02500 = 2.500" 11000 = 11.000" Seal Height Designation Examples: 083 = 0.083" 130 = 0.130" 170 = 0.170" 260 = 0.260" 355 = 0.355" Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
FlexiSeal Gland Type Classification FB = Inch/Fractional or Metric Rod & Piston FR = MIL-G-5514 Groove Rod FP = MIL-G-5514 Groove Piston FE = External Face Seal FI = Internal Face Seal FC = Rotary Shaft Centered O-Ring FH = Rotary Shaft O-Ring in Heel FF = Rotary Shaft Flanged 4-Digit Material Code Examples: 0502 = Carbon Fiber Filled PTFE 0203 = Fiberglass Filled PTFE
FBC-V FRC-V FPC-V
FBS-V FRS-V FPS-V
FBG-V FRG-V FPG-V
FBD-V FRD-V FPD-V
FBK-V FRK-V FPK-V
FBM-V FRM-V FPM-V
FBL-V FRL-V FPL-V
FBN-H FRN-H FPN-H
FBS-H FRS-H
FBG-H FPG-H
FBN-C FRN-C FPN-C
FBS-C FPS-C
FBG-C FRG-C
FEC-V
FED-V
FEK-V
FEN-C
FEN-H
FIN-H
FIC-V
FID-V
FIK-V
FIN-C
FCC-C
FCC-V
FCS-V
FCS-C
FHC-V
FHS-V
FHC-C
FHS-C
FFC-V
FFS-V
FFC-C
FFS-C
FFN-H 01/15/07
4-3
www.parkerseals.com
Product Offering
Table 4-1. FlexiSeal Part Number Nomenclature (Continued)
Metric M 5 0 2 FB S 0 4 0 0 0 6 5 0 0 0 6 7 S C L
Gland Cross-Section Examples: 0200 = 2.00 mm 0250 = 2.50 mm 0400 = 4.00 mm 0500 = 5.00 mm 0700 = 7.00 mm
Gland Inside Diameter (Rod or Groove Diameter) Examples: 00800 = 88.00 mm 01150 = 11.50 mm 06500 = 65.00 mm Seal Height Designation Examples: 021 = 2.1 mm 033 = 3.3 mm 043 = 4.3 mm 066 = 6.6 mm 090 = 9.0 mm Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
Lip Style Designation N = Default Lip Style C = Chamfered ID & OD S = Scraper ID G = Scraper OD D = Dual Scraper K = Beaded ID & OD L = Beaded ID & Scraper OD M = Scraper ID & Beaded OD FlexiSeal Gland Type Classification FB = Inch/Fractional or Metric Rod & Piston FE = External Face Seal FI = Internal Face Seal FC = Rotary Shaft Centered O-Ring FH = Rotary Shaft O-Ring in Heel FF = Rotary Shaft Flanged 4-Digit Material Code Examples: M502 = Carbon Fiber Filled PTFE M301 = Graphite Filled PTFE (M indicates metric)
FBC-V
FBS-V
FBG-V
FBD-V
FBK-V
FBM-V
FBL-V
FBN-H
FBS-H
FBG-H
FBN-C
FBS-C
FBG-C
FEC-V
FED-V
FEK-V
FEN-C
FEN-H
FIN-H
FIC-V
FID-V
FIK-V
FIN-C
FCC-C
FCC-V
FCS-V
FCS-C
FHC-V
FHS-V
FHC-C
FHS-C
FFC-V
FFS-V
FFC-C
FFS-C
FFN-H
01/15/06
4-4
www.parkerseals.com
Product Offering Part Number Nomenclature FlexiLip

Table 4-2. FlexiLip Part Number Nomenclature
English 0 5 0 2 LF N 3 7 5 0 2 5 0 0 2 5 0 N S
4-Digit Material Code Examples: 0502 = Carbon Fiber 0502 = Filled PTFE 0301 = Graphite Filled 0502 = PTFE
Gland Cross-Section Examples: 250 = 0.250" 375 = 0.375" 750 = 0.750" Excluder Lip Designation E = Excluder Lip N = No Excluder Lip FlexiLip Lip Style Designation LF = Mandrel Formed Lip LM = Machined Lip LE = Elf-Shoe Lip LD = Dual Lips LG = Garter Spring Lip Shaft Diameter Examples: 00500 = 0.500" 02500 = 2.500" 11000 = 11.000"
Seal Height Designation 250 = 0.250" 375 = 0.375" 750 = 0.750" O-Ring Material Designation N= Nitrile (NBR) V= Fluorocarbon V= (FKM) E= EPDM S= Silicone Metal Band Designation S = Stainless Steel Band N = No Metal Band
Metric M 5 0 2 LF N 1 4 0 0 1 2 0 0 0 2 0 0 N S
4-Digit Material Code Examples: M502 = Carbon Fiber M502 = Filled PTFE M301 = Graphite Filled M502 = PTFE (M indicates metric)
Gland Cross-Section Examples: 0900 = 9.00 mm 1250 = 12.50 mm 1400 = 14.00 mm Excluder Lip Designation E = Excluder Lip N = No Excluder Lip Shaft Diameter Examples: 00505 = 5.05 mm 05050 = 50.50 mm 12000 = 120.00 mm
Seal Height Designation 090 = 9.0 mm 200 = 20.0 mm 384 = 38.4 mm O-Ring Material Designation N= Nitrile (NBR) V= Fluorocarbon V= (FKM) E= EPDM S= Silicone Metal Band Designation S = Stainless Steel Band N = No Metal Band
FlexiLip Lip Style Designation LF = Mandrel Formed Lip LM = Machined Lip LE = Elf-Shoe Lip LD = Dual Lips LG = Garter Spring Lip
LFN-N
LEN-N
LDN-N
LMN-N
LFE-N
LEE-N
LDE-N
LGN-N
LFN-S
LEN-S
LDN-S
LMN-S
LFE-S
LEE-S
LDE-S
LGN-S 01/15/06
4-5
www.parkerseals.com
Product Offering Part Number Nomenclature FlexiCase

Table 4-3. FlexiCase Part Number Nomenclature
English 0 5 0 2 CF E 2 5 0 0 0 8 7 5 2 5 0 N S
Gland Cross-Section Examples: 250 = 0.250" 375 = 0.375" 750 = 0.750" Excluder Lip Designation E = Excluder Lip N = No Excluder Lip
Seal Height Designation 250 = 0.250" 375 = 0.375" 750 = 0.750" Shaft Diameter Examples: 00500 = 0.875" 02500 = 2.500" 11000 = 11.000" Internal Gasket Material Designation N = Nitrile (NBR) V = Fluorocarbon (FKM) E = EPDM A = Special Paper Metal Case Material Designation S = 304 Stainless Steel C = Cold Rolled Steel Z = Zinc Plated CRS A = Aluminum
FlexiCase Lip Style Designation CF = Mandrel Formed Lip CM = Machined Lip CE = Elf-Shoe Lip CD = Dual Lips CG = Garter Spring Lip CJ = Dual Lip w/Garter Spring on Primary Lip CH = Dual Lip High Pressure
Metric M 5 0 2 CF E 1 4 0 0 1 2 0 0 0 2 0 0 N S
Gland Cross-Section Examples: 0900 = 9.00 mm 1250 = 12.50 mm 1400 = 14.00 mm Excluder Lip Designation E = Excluder Lip N = No Excluder Lip
Seal Height Designation 090 = 9.0 mm 200 = 20.0 mm 384 = 38.4 mm Shaft Diameter Examples: 00705 = 7.05 mm 05050 = 50.50 mm 12000 = 120.00 mm Internal Gasket Material Designation N = Nitrile (NBR) V = Fluorocarbon (FKM) E = EPDM A = Special Paper
Metal Case Material Designation S = 304 Stainless Steel C = Cold Rolled Steel Z = Zinc Plated CRS A = Aluminum
CFN
CMN
CEN
CDN
CGN
CJN
CHN
CFE
CME
CEE
CDE
CGE
CJE
CHE 01/15/06
4-6
www.parkerseals.com
Product Offering Profiles

Table 4-4. FlexiSeal Rod & Piston Product Profiles
Profile
FBC-V, FPC-V, FRC-V
Features
Chamfered ID & OD, Cantilever Spring
Recommended Applications
Maximum sealability on ID & OD.
Profile
Features
High radial load increases sealability and friction.
FBN-H, FPN-H, FRN-H Rounded ID & OD, Helical Spring
FBS-V, FPS-V, FRS-V
Scraper ID, Scrapes Chamfered OD, contamination from Cantilever Spring rod surface.
FBS-H, FRS-H
Scraper ID, Rounded OD, Helical Spring
Scrapes contamination from rod surface.
4
FBG-V, FPG-V, FRG-V Scraper OD, Scrapes Chamfered ID, contamination from Cantilever Spring bore surface. FBG-H, FPG-H Scraper OD, Rounded ID, Helical Spring Scrapes contamination from bore surface.
FBD-V, FPD-V, FRD-V
Scraper ID & OD, Best overall in Cantilever Spring contaminated media.
FBN-C, FPN-C, FRN-C Back-beveled ID & OD, CantedCoil Spring
Low radial load decreases friction and sealability.
FBK-V, FPK-V, FRK-V
Beaded ID & OD, Beaded lip similar to Cantilever Spring O-ring contact area.
FBS-C, FPS-C
Scraper ID, Chamfered OD, Canted-Coil Spring
Easily snaps into a stepped gland for a piston seal.
FBM-V, FPM-V, FRM-V Scraper ID, Scrapes Beaded OD, contamination from Cantilever Spring rod surface.
FBG-C, FRG-C
Scraper OD, Chamfered ID, Canted-Coil Spring
Easily snaps into a stepped gland for a rod seal.
FBL-V, FPL-V, FRL-V
Scraper OD, Scrapes Beaded ID, contamination from Cantilever Spring bore surface.
See a more detailed product offering for FlexiSeal Rod & Piston Seals on Page 5-8.
FlexiSeal Rod & Piston Seals Part Number Example

0 5 0 2
FB C
1 2 5
0 0 5 0 0
1 6 0
01/15/06
4-7
www.parkerseals.com
Product Offering
Table 4-5. FlexiSeal Face Product Profiles
Profile
FEN-H
Features
Lips Facing Out, Rounded Lips, Helical Spring
Seals external pressure. High sealability and closure force. FIN-H
Profile
Features
Lips Facing In, Rounded Lips, Helical Spring
Seals internal pressure. High sealability and closure force.
FEC-V
Lips Facing Out, Chamfered Lips, Cantilever Spring
Seals external pressure. Good sealability for nonabrasive fluids.
FIC-V
Lips Facing In, Chamfered Lips, Cantilever Spring
Seals internal pressure. Good sealability for nonabrasive fluids.
FED-V
Lips Facing Out, Scraper Lips, Cantilever Spring
Seals external pressure. Good sealability for abrasive fluids.
FID-V
Lips Facing In, Scraper Lips, Cantilever Spring
Seals internal pressure. Good sealability for abrasive fluids.
FEK-V
Lips Facing Out, Beaded Lips, Cantilever Spring
Seals external pressure. Good sealability for nonabrasive fluids. Rounded like O-ring.
FIK-V
Lips Facing In, Beaded Lips, Cantilever Spring
Seals internal pressure. Good sealability for nonabrasive fluids. Rounded like O-ring.
FEN-C
Lips Facing Out, Back-Beveled Lips, Canted-Coil Spring
Seals external pressure. Low closure force for non-abrasive fluids.
FIN-C
Lips Facing In, Back- Seals internal Beveled Lips, pressure. Low Canted-Coil Spring closure force for non-abrasive fluids.
See a more detailed product offering for FlexiSeal Face Seals on Page 6-6.
FlexiSeal Face Seals Part Number Example

0 3 0 1
FE N
1 2 5
0 1 2 5 0
1 6 0
01/15/06
4-8
www.parkerseals.com
Product Offering
Table 4-6. FlexiSeal Rotary Product Profiles
Profile
FCC-V
Features
O-Ring Centered in OD, Chamfered ID, Cantilever Spring
Optimum sealability. Available in 0.125" cross-section and higher.
Profile
FHC-C
Features
O-Ring in Heel OD, Chamfered ID, Canted-Coil Spring
Reduced friction and sealability. Available in extended heel option only.
FHS-C
FCS-V
O-Ring Centered in OD, Scraper ID, Cantilever Spring
Minimizes contamination threat. Available in 0.125" cross-section and higher.
O-Ring in Heel OD, Low friction with Scraper ID, Canted- contamination Coil Spring resistance. Available in extended heel option only. Flanged Heel OD, Chamfered ID, Cantilever Spring Optimum sealability. Premium bore retention.
FFC-V
4
FCC-C O-Ring Centered in OD, Chamfered ID, Canted-Coil Spring Reduced friction and sealability. Available in 0.125" crosssection and higher. FFS-V Flanged Heel OD, Scraper ID, Cantilever Spring Minimizes contamination threat. Premium bore retention.
FFC-C FCS-C O-Ring Centered in OD, Scraper ID, Canted-Coil Spring Low friction with contamination resistance. Available in 0.125" crosssection and higher. FFS-C
Flanged Heel OD, Chamfered ID, Canted-Coil Spring
Reduced friction and sealability. Premium bore retention.
Flanged Heel OD, Low friction with Scraper ID, Canted- contamination Coil Spring resistance. Premium bore retention.
FHC-V
O-Ring in Heel OD, Chamfered ID, Cantilever Spring
Optimum sealability. Available in extended heel option only.
FFN-H
Flanged Heel OD, Rounded ID, Helical Spring
FHS-V
O-Ring in Heel OD, Scraper ID, Cantilever Spring
Minimizes contamination threat. Available in extended heel option only.
Static or intermittent rotary only. High sealability and friction.
See a more detailed product offering for FlexiSeal Rotary Seals on Page 7-7.
FlexiSeal Rotary Seals Part Number Example

0 5 0 2
FC C
1 2 5
0 0 5 0 0
1 6 0
01/15/06
4-9
www.parkerseals.com
Product Offering
Table 4-7. FlexiLip Product Profiles
Profile
LFN-N
Features
Formed Primary Lip
Multipurpose Seal
Profile
LFN-S
Features
Formed Primary Lip w/ Metal Band
Multipurpose Seal
LFE-N
Formed Primary Lip w/ Excluder Lip
Multipurpose Seal
LFE-S
Formed Primary Lip w/ Excluder Lip w/ Metal Band
Multipurpose Seal
LMN-N
Machined Primary Lip
Low Friction
LMN-S
Machined Primary Lip w/ Metal Band
Low Friction
LEN-N
Elf-Toe Primary Lip
Abrasive Media
LEN-S
Elf-Toe Primary Lip w/ Metal Band
Abrasive Media
LEE-N
Elf-Toe Primary Lip w/ Excluder Lip
Abrasive Media
LEE-S
Elf-Toe Primary Lip w/ Excluder Lip w/ Metal Band
Abrasive Media
LDN-N
Dual Primary Lips
Oil Seal Flooded, Severe Splash
LDN-S
Dual Primary Lips w/ Metal Band
LDE-N
Dual Primary Lips w/ Excluder Lip
LDE-S
Dual Primary Lips w/ Excluder Lip w/ Metal Band
LGN-N
Primary Lip Energized with Garter Spring
0.020" > TIR > 0.005"
LGN-S
Primary Lip Energized with Garter Spring w/ Metal Band
0.020" > TIR > 0.005"
See a more detailed product offering for FlexiLip Seals on Page 8-8.
FlexiLip Seals Part Number Example

0 5 0 2
LF N
2 5 0
0 0 5 0 0
2 5 0
N
01/15/06
4-10
www.parkerseals.com
Product Offering
Table 4-8. FlexiCase Product Profiles
Profile
CFN
Features
Formed Primary Lip
General purpose rotary shaft seal. CDE
Profile
Features
Redundant sealing for aircraft or other low leakage systems. Keeps water & dirt out.
CFE
Ideal to keep oil in and water & dirt out.
CGN
Use when shaft runout is 0.010" to 0.020" or abrasive media.
CMN
General purpose rotary shaft seal w/ low breakaway torque.
CGE
Primary Lip Energized with Garter Spring w/ Excluder Lip
Use when shaft runout is 0.010" to 0.020" or abrasive media. Keeps water & dirt out.
CME
Machined Primary Lip w/ Excluder Lip
Ideal to keep oil in and water & dirt out. Low Breakaway torque.
CJN
Dual Lip Seal w/ Primary Lip Energized with Garter Spring
Use when redundant sealing is needed & shaft runout is 0.010" to 0.020" or abrasive media.
CEN
Elf-Toe Primary Lip
General purpose rotary shaft seal where shaft runout is 0.005" to 0.010" or abrasive media.
CJE
Dual Lip Seal w/ Primary Lip Energized with Garter Spring w/ Excluder Lip
Use when redundant sealing is needed & shaft runout is 0.010" to 0.020" or abrasive media. Keeps water & dirt out.
CEE
Ideal to keep oil in and water & dirt out where shaft runout is 0.005" to 0.010" or abrasive media.
CHN
High Pressure Dual- Redundant seal for Lip Seal with Metal high pressure Backup Washer aircraft or other low leakage systems.
CDN
Dual Primary Lips
Redundant sealing for aircraft or other low leakage systems.
CHE
High Pressure Duallip Seal with Metal Backup Washer w/ Excluder Lip
Redundant seal for high pressure aircraft or other low leakage systems. Keeps water & dirt out.
See a more detailed product offering for FlexiCase Seals on Page 9-8.
FlexiCase Seals Part Number Example

0 5 0 2
CF N
2 5 0
0 0 8 7 5
2 5 0
01/15/06
4-11
www.parkerseals.com
Notes
4-12
www.parkerseals.com
EPS 5340.book Page 1 Wednesday, January 11, 2006 10:30 AM
FlexiSeal Rod & Piston Seals Introduction

Contents
Engineering . . . . . . . . . . . . . . . . . Materials . . . . . . . . . . . . . . . . . . . Product Offering . . . . . . . . . . . . . FlexiSeal Rod & Piston FB Profiles Inch/Fractional . . . . . . . . . . . . 5-10 FB Profiles Metric . . . . . . . . . . . . . . . . . . . 5-17 FR Profiles MIL-G-5514 Rod . . . . . . . . . . . 5-19 FP Profiles MIL-G-5514 Piston . . . . . . . . . 5-24 5-2 5-3 5-4
Where can the reciprocating FlexiSeal be found?
The Parker FlexiSeal was not specifically designed for just one industry or application. The chemical and physical properties of its compounds make it a powerful problemsolver in many situations. The seals always seem to gravitate toward certain difficult applications which include: Harsh chemicals and solvents High temperatures up to 600 F Cryogenic temperatures down to -450 F Unlubricated applications Where low friction is required High pressures up to 10,000 psi High surface speeds when other seals overheat Where theres no margin for tooling cost Where there are custom, in-between sizes
FlexiSeals
Applications
The FlexiSeals versatility makes it suitable for a wide range of applications including:
Compressors Cryogenics FDA Clean Grade Jet Engines Hydraulic Cylinders Paint Sprayers Pressure Washers Robotics Steering Cylinders Valves Vapor Recovery Systems Many more
Markets
Rod Gland Piston Gland
Since the FlexiSeal solves problems along several parameters, it can be found in virtually every market including:
Aerospace Automotive Chemical Processing Appliances Machine Tools Marine Medical Pharmaceutical Military Heavy Machinery Pulp & Paper Hydraulic Food & Beverage Electronic Oil & Gas Semiconductor Plastics 01/15/06
Chamfered Rod/Piston Seal with Cantilever Spring
5-1
www.parkerseals.com
FlexiSeal Rod & Piston Seals Engineering

Choosing the Right Design
While choosing the right rod or piston FlexiSeal for your application, you need to consider the glands configuration and intended installation, the finish and hardness of the mating surface, the pressure it will be subjected to, and the advantages of different spring choices and lip shapes.
Spring Choices
FlexiSeal Rod and Piston Seals are available with three different spring types to energize the jacket: V-shaped cantilever springs (V Series), canted-coil springs (C Series) and helical wound-ribbon springs (H Series). Details on each of their features can be found beginning on Page 2-12. An O-ring energizer can easily be substituted as a custom design.
Hardware Configuration and Installation

FlexiSeals are available for twopiece, stepped and closed gland configurations. We recommend a twopiece gland design for rod and piston applications for its ease of installation. The step-cut design may be used when the seal sees pressure from the open or spring side of the seal. A closed gland may only be used if it is possible to stretch or compress the seal into position. For details on these configurations and installation considerations, see Page 2-3.
V Series / Cantilever
C Series / Canted Coil
H Series / Helical
Surface Finish
The optimum surface finish for FlexiSeals depends on the media to be sealed. To maximize seal performance and life, follow our recommendations on Page 2-9.
Table 5-1. Recommended Applications for FlexiSeal Rod and Piston Springs
V Series reciprocating rod and piston wide tolerance and misaligned glands (static) C Series reciprocating rod and piston wide tolerance and misaligned glands (static) H Series static rod and piston very slow dynamic seals (<150 sfpm)
Pressure
The standard FlexiSeal is rated to 3000 psi when used in glands conforming to recommended dimensions and using the materials that meet the temperature requirements of the application, while a FlexiSeal with an extended heel can hold up to 10,000 psi. See Page 2-10 for more detailed recommendations regarding pressure ratings.
abrasive media (when friction critical and very applications where scraper lip is small diameter sealability is critical designated) applications
Lip Shapes
FlexiSeals can be optimized by changing their lip shapes. Chamfered lips contact the mating surface at a single point. Scraper lips prevent particles from accumulating. Beaded lips yield an even thicker film than chamfered lips, advantageous for rapid reciprocating applications. More information is available on Page 2-16.
01/15/06
5-2
www.parkerseals.com
FlexiSeal Rod & Piston Seals Materials

Common Materials Used in this Product
The most popular PTFE fillers used for FlexiSeal rod & piston products are carbon fiber, fiberglass, aromatic polyester and graphite. Virgin PTFE is also popular for these products when conditions are mild. 0502 Carbon Fiber Filled
Carbon fiber lowers creep, increases flex and compressive modulus and raises hardness. Coefficient of thermal expansion is lowered and thermal conductivity is higher for compounds of carbon fiber filled PTFE. Ideal for automotive applications in shock absorbers and water pumps. 0203 Fiberglass Filled Glass fiber has a positive impact on creep performance of PTFE. It also adds wear resistance and offers good compression strength.
5
0601 Aromatic Polyester Filled A number of other fillers are used in combination with PTFE. Non-PTFE compounds are also available. More information on these materials and their properties is available in Tab 3. For best results consult the EPS Division PTFE Application Engineering team at (801) 972-3000. Aromatic polyester is excellent for high temperatures and has excellent wear resistance against soft, dynamic surfaces. Not recommended for sealing applications involving steam. 0301 Graphite Filled Since graphite is often used as a lubricant, it does not significantly increase the coefficient of friction of PTFE when used as a filler. The low friction allows the compound to be used when both shaft speed and pressure are high. Graphite also is chemically inert which enables its use in corrosive medias.
01/15/06
5-3
www.parkerseals.com
FlexiSeal Rod & Piston Seals Product Offering

Decision Trees
There are two decision trees in this section. The first one deals with static and slow reciprocating applications where the seals are being squeezed radially between their ID and OD. Face seals, which are usually static or slow rotary, are covered on Page 6-4. The second decision tree on Page 5-5 deals with radial seals that experience regular dynamic motion. The key application considerations for static & intermittent dynamic rod & piston FlexiSeals are gland configuration and pressure. Pressures above 3000 psi call for the extended heel option, which is further explained on Page 5-10. The key application considerations for dynamic reciprocating applications are pressure, media abrasiveness, friction requirements, and gland configuration. The decision trees in this guide are to be used as an engineering guide only. Often several other parameters must be considered to optimize seal design. Contact Parkers PTFE Engineering Team for confirmation of your choice or further recommendations. Parker also recommends that any seal be tested in the application conditions before releasing for production.
Static & Intermittent Dynamic Rod & Piston Applications
Dynamic Seal Surface?
FPN-H x-heel * Page 5-24

OD ID
FRN-H x-heel * Page 5-19 psi > 3000?

Yes No
FPN-H Page 5-24 Groove Type: MIL-G-5514? Inch/ Fractional?

OD
ID
FRN-H Page 5-19
FBN-H x-heel * Pages 5-10 and 5-17

Yes
psi > 3000?
No
FBN-H Pages 5-10 and 5-17
* See Extended Heel Options on Page 5-10.
01/15/06
5-4
www.parkerseals.com
FlexiSeal Rod & Piston Seals

Dynamic Reciprocating Applications
Consult EPS Division Engineering >10,000 psi?
Product Offering
** 3000 to 10,000 psi? Follow the Decision Tree and add extended heel option. * Pressure >3000 psi? Dynamic Seal Surface? FRM-V FRS-V Page 5-19
ID OD
** FPL-V FPG-V Page 5-24 ** FBM-V FBS-V Pages 5-10 and 5-17
Yes No
Groove Type: MIL-G-5514? Inch/ Fractional? Dynamic Seal Surface?
ID OD
** FBL-V FBG-V Pages 5-10 and 5-17
Sealing Abrasive Media?
Yes No
** FRK-V FRC-V Page 5-19

ID OD
Dynamic Seal Surface? Groove Type: MIL-G-5514? Inch/ Fractional?
** FPK-V FPC-V Page 5-24 ** FBK-V FBC-V Pages 5-10 and 5-17
No
** FRN-C FRG-C Page 5-19

ID OD
Low Seal Friction Required?
Yes
** FPN-C FPS-C Page 5-24
Groove Type: MIL-G-5514? Inch/ Fractional? Stepped Gland?

No Yes
FBN-C Pages 5-10 and 5-17
Dynamic Seal Surface? ** See Extended Heel Options on Page 5-10. ** Which seal profile? See Pages 2-16 and 2-17 for further optimization of lip shape.
FBG-C Pages 5-10 and 5-17

ID OD
FBS-C Pages 5-10 and 5-17 01/15/06
5-5
www.parkerseals.com
Product Offering
Part Number Nomenclature FlexiSeal Rod & Piston

Table 5-2. FlexiSeal Rod & Piston Part Number Nomenclature
English 0 5 0 2 FB S 1 2 5 0 0 5 0 0 1 7 0 S C L
Gland Cross-Section Examples: 062 = 0.062" 093 = 0.093" 125 = 0.125" 187 = 0.187" 250 = 0.250" Lip Style Designation N = Default Lip Style C = Chamfered ID & OD S = Scraper ID G = Scraper OD D = Dual Scraper K = Beaded ID & OD L = Beaded ID & Scraper OD M = Scraper ID & Beaded OD
Gland Inside Diameter (Rod or Groove Diameter) Examples: 00500 = 0.500" 02500 = 2.500" 11000 = 11.000" Seal Height Designation Examples: 083 = 0.083" 130 = 0.130" 170 = 0.170" 260 = 0.260" 355 = 0.355" Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
FlexiSeal Gland Type Classification FB = Inch/Fractional or Metric Rod & Piston FR = MIL-G-5514 Groove Rod FP = MIL-G-5514 Groove Piston 4-Digit Material Code Examples: 0502 = Carbon Fiber Filled PTFE 0203 = Fiberglass Filled PTFE
FBC-V FRC-V FPC-V
FBS-V FRS-V FPS-V
FBG-V FRG-V FPG-V
FBD-V FRD-V FPD-V
FBK-V FRK-V FPK-V
FBM-V FRM-V FPM-V
FBL-V FRL-V FPL-V
FBN-H FRN-H FPN-H
FBS-H FRS-H
FBG-H FPG-H
FBN-C FRN-C FPN-C
FBS-C FPS-C
FRG-C FBG-C
01/15/07
5-6
www.parkerseals.com

Table 5-2. FlexiSeal Rod & Piston Part Number Nomenclature (Continued)
Product Offering
Metric M 5 0 2 FB S 0 5 0 0 0 1 9 0 0 0 6 6 S C L
Gland Cross-Section Examples: 0200 = 2.00 mm 0250 = 2.50 mm 0400 = 4.00 mm 0500 = 5.00 mm 0700 = 7.00 mm Lip Style Designation N = Default Lip Style C = Chamfered ID & OD S = Scraper ID G = Scraper OD D = Dual Scraper K = Beaded ID & OD L = Beaded ID & Scraper OD M = Scraper ID & Beaded OD
Gland Inside Diameter (Rod or Groove Diameter) Examples: 00800 = 88.00 mm 01150 = 11.50 mm 06500 = 65.00 mm Seal Height Designation Examples: 021 = 2.1 mm 033 = 3.3 mm 043 = 4.3 mm 066 = 6.6 mm 090 = 9.0 mm Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
FlexiSeal Gland Type Classification FB = Inch/Fractional or Metric Rod & Piston 4-Digit Material Code Examples: M502 = Carbon Fiber Filled PTFE M301 = Graphite Filled PTFE (M indicates metric)
FBC-V
FBS-V
FBG-V
FBD-V
FBK-V
FBM-V
FBL-V
FBN-H
FBS-H
FBG-H
FBN-C
FBS-C
FBG-C
01/15/06
5-7
www.parkerseals.com

Table 5-3. Product Profiles
Profile Features Recommended Applications Available as Standard in High Pressure Extended Heel (up to 10,000 psi) Friction
Low Pressure Sealability Very Good
Good in Abrasive Media No
Gland Dimension Available in Mil-G-5514 Table Glands Location Yes FBC-V Pages 5-10, 5-17 FRC-V Page 5-19 FPC-V Page 5-24 Yes FBS-V Pages 5-10, 5-17 FRS-V Page 5-19 FPS-V Page 5-24 Yes FBG-V Pages 5-10, 5-17 FRG-V Page 5-19 FPG-V Page 5-24 Yes FBD-V Pages 5-10, 5-17 FRD-V Page 5-19 FPD-V Page 5-24 Yes FBK-V Pages 5-10, 5-17 FRK-V Page 5-19 FPK-V Page 5-24 Yes FBM-V Pages 5-10, 5-17 FRM-V Page 5-19 FPM-V Page 5-24 Yes FBL-V Pages 5-10, 5-17 FRL-V Page 5-19 FPL-V Page 5-24
FBC-V, FPC-V, FRC-V
Chamfered ID & OD, Cantilever Spring
Maximum Yes sealability on ID & OD.
Medium
FBS-V, FPS-V, FRS-V
Scraper ID, Chamfered OD, Cantilever Spring
Yes
Medium
Very Good
Yes
FBG-V, FPG-V, FRG-V
Scraper OD, Chamfered ID, Cantilever Spring
Scrapes contamination from bore surface.
Yes
Medium
Very Good
Yes
FBD-V, FPD-V, FRD-V
Best overall in Scraper ID & OD, Cantilever contaminated media. Spring
Yes
Medium
Very Good
Yes
FBK-V, FPK-V, FRK-V
Beaded ID & Beaded lip OD, Cantilever similar to Spring O-ring contact area.
Yes
Medium
Very Good
No
FBM-V, FPM-V, FRM-V
Scraper ID, Beaded OD, Cantilever Spring
Yes
Medium
Very Good
Yes
FBL-V, FPL-V, FRL-V
Scraper OD, Beaded ID, Cantilever Spring
Yes
Medium
Very Good
Yes
01/15/06
5-8
www.parkerseals.com

Table 5-3. Product Profiles (Continued)
Profile Features Recommended Applications Available as Standard in High Pressure Extended Heel (up to 10,000 psi) Friction Low Pressure Sealability Excellent Good in Abrasive Media No
Product Offering
Gland Dimension Available in Mil-G-5514 Table Glands Location Yes FBN-H Pages 5-10, 5-17 FRN-H Page 5-19 FPN-H Page 5-24 Yes FBS-H Pages 5-10, 5-17 FRS-H Page 5-19
FBN-H, FPN-H, FRN-H
Rounded ID & High radial load Yes OD, Helical increases Spring sealability and friction.
High
FBS-H, FRS-H
Scraper ID, Rounded OD, Helical Spring
Yes
High
Excellent
Yes
FBG-H, FPG-H
Scraper OD, Rounded ID, Helical Spring
Yes
High
Excellent
Yes
Yes FBG-H Pages 5-10, 5-17 FPG-H Page 5-24
FBN-C, FPN-C, FRN-C
Back-beveled ID & OD, Canted-Coil Spring
Low radial load Yes decreases friction and sealability.
Low
Good
No
Yes FBN-C Pages 5-10, 5-17 FRN-C Page 5-19 FPN-C Page 5-24 Yes FBS-C Pages 5-10, 5-17 FPS-C Page 5-24
FBS-C, FPS-C
Scraper ID, Chamfered OD, CantedCoil Spring
Easily snaps into a stepped gland for a piston seal.
Yes
Low
Good
No
FBG-C, FRG-C
Scraper OD, Chamfered ID, Canted-Coil Spring
Easily snaps into a stepped gland for a rod seal.
Yes
Low
Good
No
FBG-C Yes Pages 5-10, 5-17 FRG-C Page 5-19
01/15/06
5-9
www.parkerseals.com
FlexiSeal Rod & Piston Seals FB Profiles Inch/Fractional

FB Profiles
All of these FB profiles will fit into the Industrial Inch/ Fractional gland tables on the following pages. Metric part numbers begin with an M and appear on Page 5-17.
Design Considerations
Hardware Configurations/Installation, see Page 2-3 Surface Finish and Hardness, see Page 2-9 Extrusion Gaps and High Pressure, see Page 2-10 Spring Choices, see Page 2-12 Lip Shapes, see Page 2-16 Shaft Misalignment Issues, see Page 2-19
Groove Width Seal Height
Part Number Example

Table 5-5. FB Inch/Fractional Part Number
0 5 0 2
FB C
1 2 5
0 0 5 0 0
1 7 0
Inch/Fractional Rod & Piston Chamfered ID & OD Lip
Cantilever Spring
Extended Heel Option

All part numbers on the following pages call for the standard seal height for pressures below 3000 psi.
Standard Heel Extended Heel
The heel of a FlexiSeal can be extended to increase extrusion resistance simply by changing the seal height callout in the part number.
0 5 0 2 F B C 0 6 2 0 1 1 2 5
Table 5-4. Seal Height Callouts

Radial Cross-Section 062 093 125 187 250 Standard Heel Callout 083 130 170 260 355 Extended Heel Callout 140 165 220 310 450
0 8 3
S V M
Seal Height
Just find where the G dimension for the groove width is designated in the gland tables and switch to the longer extended heel callout in the part number.
0 5 0 2 F B C 0 6 2 0 1 1 2 5
1 4 0
S V M
Seal Height
01/15/07
5-10
www.parkerseals.com
FlexiSeal Rod & Piston Seals Gland Dimensions FB Profiles

Table 5-6. FB Inch/Fractional Gland Dimensions
FB Profiles Inch/Fractional
G G E E
A B R
A B
R
Rod Seal Piston Seal
Each of these FlexiSeal profiles were designed to fit into either the Inch/Fractional glands on the following pages or the Metric glands on Page 5-17.
FBC-V
FBS-V
FBG-V
FBD-V
FBK-V
FBM-V
FBL-V
FBN-H
FBS-H
FBG-H
FBN-C
FBS-C
A B Rod or Bore or Part Number Groove Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.094/0.104" (083 callout) G for Extended heel groove = 0.149/0.159" (140 callout) +.000/ +.001/ -.001 -.000 -006 0.125 0.250 xxxxFBx06200125083xxx -007 0.156 0.281 xxxxFBx06200156083xxx -008 0.187 0.312 xxxxFBx06200187083xxx -009 0.218 0.343 xxxxFBx06200218083xxx -010 0.250 0.375 xxxxFBx06200250083xxx -011 0.312 0.437 xxxxFBx06200312083xxx -012 0.375 0.500 xxxxFBx06200375083xxx -013 0.437 0.562 xxxxFBx06200437083xxx -014 0.500 0.625 xxxxFBx06200500083xxx -015 0.562 0.687 xxxxFBx06200562083xxx -016 0.625 0.750 xxxxFBx06200625083xxx -017 0.687 0.812 xxxxFBx06200687083xxx -018 0.750 0.875 xxxxFBx06200750083xxx -019 0.812 0.937 xxxxFBx06200812083xxx -020 0.875 1.000 xxxxFBx06200875083xxx -021 0.937 1.062 xxxxFBx06200937083xxx -022 1.000 1.125 xxxxFBx06201000083xxx -023 1.062 1.187 xxxxFBx06201062083xxx -024 1.125 1.250 xxxxFBx06201125083xxx -025 1.187 1.312 xxxxFBx06201187083xxx -026 1.250 1.375 xxxxFBx06201250083xxx -027 1.312 1.437 xxxxFBx06201312083xxx -028 1.375 1.500 xxxxFBx06201375083xxx -029 1.500 1.625 xxxxFBx06201500083xxx -030 1.625 1.750 xxxxFBx06201625083xxx -031 1.750 1.875 xxxxFBx06201750083xxx -032 1.875 2.000 xxxxFBx06201875083xxx -033 2.000 2.125 xxxxFBx06202000083xxx -034 2.125 2.250 xxxxFBx06202125083xxx Dash # 01/15/06
FBG-C
5-11
www.parkerseals.com
Table 5-6. FB Inch/Fractional Gland Dimensions (Continued)
G G E E
A B R
A B
R
Rod Seal A B Rod or Bore or Part Number Groove Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.094/0.104" (083 callout) G for Extended heel groove = 0.149/0.159" (140 callout) +.000/ +.001/ -.001 -.000 -035 2.250 2.375 xxxxFBx06202250083xxx -036 2.375 2.500 xxxxFBx06202375083xxx -037 2.500 2.625 xxxxFBx06202500083xxx -038 2.625 2.750 xxxxFBx06202625083xxx -039 2.750 2.875 xxxxFBx06202750083xxx -040 2.875 3.000 xxxxFBx06202875083xxx -041 3.000 3.125 xxxxFBx06203000083xxx -042 3.250 3.375 xxxxFBx06203250083xxx -043 3.500 3.625 xxxxFBx06203500083xxx -044 3.750 3.875 xxxxFBx06203750083xxx -045 4.000 4.125 xxxxFBx06204000083xxx R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.141/0.151" (130 callout) G for Extended heel groove = 0.183/0.193" (165 callout) +.000/ +.002/ -.002 -.000 -106 0.187 0.375 xxxxFBx09300187130xxx -107 0.219 0.406 xxxxFBx09300219130xxx -108 0.250 0.437 xxxxFBx09300250130xxx -109 0.312 0.500 xxxxFBx09300312130xxx -110 0.375 0.562 xxxxFBx09300375130xxx -111 0.437 0.625 xxxxFBx09300437130xxx -112 0.500 0.687 xxxxFBx09300500130xxx -113 0.562 0.750 xxxxFBx09300562130xxx -114 0.625 0.812 xxxxFBx09300625130xxx -115 0.687 0.875 xxxxFBx09300687130xxx -116 0.750 0.937 xxxxFBx09300750130xxx -117 0.812 1.000 xxxxFBx09300812130xxx -118 0.875 1.062 xxxxFBx09300875130xxx -119 0.937 1.125 xxxxFBx09300937130xxx -120 1.000 1.187 xxxxFBx09301000130xxx -121 1.062 1.250 xxxxFBx09301062130xxx Dash # Dash # -122 -123 -124 -125 -126 -127 -128 -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -151 -152 -153 -154 -155 -156 -157 Piston Seal A Rod or Groove Diameter 1.125 1.187 1.250 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.812 1.875 1.937 2.000 2.062 2.125 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 3.000 3.250 3.500 3.750 4.000 4.250 4.500 B Bore or Groove Diameter 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.812 1.875 1.937 2.000 2.062 2.125 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 2.937 3.000 3.062 3.187 3.437 3.687 3.937 4.187 4.437 4.687
Part Number xxxxFBx09301125130xxx xxxxFBx09301187130xxx xxxxFBx09301250130xxx xxxxFBx09301312130xxx xxxxFBx09301375130xxx xxxxFBx09301437130xxx xxxxFBx09301500130xxx xxxxFBx09301562130xxx xxxxFBx09301625130xxx xxxxFBx09301687130xxx xxxxFBx09301750130xxx xxxxFBx09301812130xxx xxxxFBx09301875130xxx xxxxFBx09301937130xxx xxxxFBx09302000130xxx xxxxFBx09302062130xxx xxxxFBx09302125130xxx xxxxFBx09302187130xxx xxxxFBx09302250130xxx xxxxFBx09302312130xxx xxxxFBx09302375130xxx xxxxFBx09302437130xxx xxxxFBx09302500130xxx xxxxFBx09302562130xxx xxxxFBx09302625130xxx xxxxFBx09302687130xxx xxxxFBx09302750130xxx xxxxFBx09302812130xxx xxxxFBx09302875130xxx xxxxFBx09303000130xxx xxxxFBx09303250130xxx xxxxFBx09303500130xxx xxxxFBx09303750130xxx xxxxFBx09304000130xxx xxxxFBx09304250130xxx xxxxFBx09304500130xxx 01/15/06
5-12
www.parkerseals.com

G G E E
A B R
A B
R
Rod Seal A B Rod or Bore or Part Number Groove Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.141/0.151" (130 callout) G for Extended heel groove = 0.183/0.193" (165 callout) +.000/ +.002/ -.002 -.000 -158 4.750 4.937 xxxxFBx09304750130xxx -159 5.000 5.187 xxxxFBx09305000130xxx -160 5.250 5.437 xxxxFBx09305250130xxx -161 5.500 5.687 xxxxFBx09305500130xxx -162 5.750 5.928 xxxxFBx09305750130xxx -163 6.000 6.187 xxxxFBx09306000130xxx R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.188/0.198" (170 callout) G for Extended heel groove = 0.235/0.245" (220 callout) +.000/ +.002/ -.002 -.000 -202 0.250 0.500 xxxxFBx12500250170xxx -203 0.312 0.562 xxxxFBx12500312170xxx xxxxFBx12500375170xxx -204 0.375 0.625 xxxxFBx12500437170xxx -205 0.437 0.687 xxxxFBx12500500170xxx -206 0.500 0.750 xxxxFBx12500562170xxx -207 0.562 0.812 xxxxFBx12500625170xxx -208 0.625 0.875 xxxxFBx12500687170xxx -209 0.687 0.937 xxxxFBx12500750170xxx -210 0.750 1.000 xxxxFBx12500812170xxx -211 0.812 1.062 xxxxFBx12500875170xxx -212 0.875 1.125 xxxxFBx12500937170xxx -213 0.937 1.187 xxxxFBx12501000170xxx -214 1.000 1.250 xxxxFBx12501062170xxx -215 1.062 1.312 xxxxFBx12501125170xxx -216 1.125 1.375 xxxxFBx12501187170xxx -217 1.187 1.437 xxxxFBx12501250170xxx -218 1.250 1.500 xxxxFBx12501312170xxx -219 1.312 1.562 xxxxFBx12501375170xxx -220 1.375 1.625 xxxxFBx12501437170xxx -221 1.437 1.687 Dash # Dash # -222 -223 -224 -225 -226 -227 -228 -229 -230 -231 -232 -233 -234 -235 -236 -237 -238 -239 -240 -241 -242 -243 -244 -245 -246 -247 -248 -249 -250 -251 -252 -253 -254 -255 -256 -257 Piston Seal A Rod or Groove Diameter 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 B Bore or Groove Diameter 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.125
5-13
www.parkerseals.com
G G E E
A B R
A B
R
Rod Seal A B Rod or Bore or Part Number Groove Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.188/0.198" (170 callout) G for Extended heel groove = 0.235/0.245" (220 callout) +.000/ +.002/ -.002 -.000 -258 6.000 6.250 xxxxFBx12506000170xxx -259 6.250 6.500 xxxxFBx12506250170xxx -260 6.500 6.750 xxxxFBx12506500170xxx xxxxFBx12506750170xxx -261 6.750 7.000 xxxxFBx12507000170xxx -262 7.000 7.250 xxxxFBx12507250170xxx -263 7.250 7.500 xxxxFBx12507500170xxx -264 7.500 7.750 xxxxFBx12507750170xxx -265 7.750 8.000 xxxxFBx12508000170xxx -266 8.000 8.250 xxxxFBx12508250170xxx -267 8.250 8.500 xxxxFBx12508500170xxx -268 8.500 8.750 -269 8.750 9.000 xxxxFBx12508750170xxx xxxxFBx12509000170xxx -270 9.000 9.250 xxxxFBx12509250170xxx -271 9.250 9.500 xxxxFBx12509500170xxx -272 9.500 9.750 xxxxFBx12509750170xxx -273 9.750 10.000 -274 10.000 10.250 xxxxFBx12510000170xxx xxxxFBx12510500170xxx -275 10.500 10.750 xxxxFBx12511000170xxx -276 11.000 11.250 xxxxFBx12511500170xxx -277 11.500 11.750 -278 12.000 12.250 xxxxFBx12512000170xxx -279 12.500 12.750 xxxxFBx12512500170xxx xxxxFBx12513000170xxx -280 13.000 13.250 xxxxFBx12513500170xxx -281 13.500 13.750 R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.281/0.291" (260 callout) G for Extended heel groove = 0.334/0.344" (310 callout) +.000/ +.002/ -.002 -.000 -310 0.500 0.875 xxxxFBx18700500260xxx -311 0.562 0.937 xxxxFBx18700562260xxx -312 0.625 1.000 xxxxFBx18700625260xxx -313 0.687 1.062 xxxxFBx18700687260xxx Dash # Dash # -314 -315 -316 -317 -318 -319 -320 -321 -322 -323 -324 -325 -326 -327 -328 -329 -330 -331 -332 -333 -334 -335 -336 -337 -338 -339 -340 -341 -342 -343 -344 -345 -346 -347 -348 -349 Piston Seal A Rod or Groove Diameter 0.750 0.812 0.875 0.937 1.000 1.062 1.125 1.187 1.250 1.312 1.375 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 B Bore or Groove Diameter 1.125 1.187 1.250 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875
5-14
www.parkerseals.com

G G E E
A B R
A B
R
Rod Seal A B Rod or Bore or Part Number Groove Groove Diameter Diameter R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.281/0.291" (260 callout) G for Extended heel groove = 0.334/0.344" (310 callout) +.000/ +.002/ -.002 -.000 -350 4.625 5.000 xxxxFBx18704625260xxx -351 4.750 5.125 xxxxFBx18704750260xxx -352 4.875 5.250 xxxxFBx18704875260xxx -353 5.000 5.375 xxxxFBx18705000260xxx -354 5.125 5.500 xxxxFBx18705125260xxx -355 5.250 5.625 xxxxFBx18705250260xxx -356 5.375 5.750 xxxxFBx18705375260xxx -357 5.500 5.875 xxxxFBx18705500260xxx -358 5.625 6.000 xxxxFBx18705625260xxx -359 5.750 6.125 xxxxFBx18705750260xxx -360 5.875 6.250 xxxxFBx18705875260xxx -361 6.000 6.375 xxxxFBx18706000260xxx -362 6.250 6.625 xxxxFBx18706250260xxx -363 6.500 6.875 xxxxFBx18706500260xxx -364 6.750 7.125 xxxxFBx18706750260xxx -365 7.000 7.375 xxxxFBx18707000260xxx -366 7.250 7.625 xxxxFBx18707250260xxx -367 7.500 7.875 xxxxFBx18707500260xxx -368 7.750 8.125 xxxxFBx18707750260xxx -369 8.000 8.375 xxxxFBx18708000260xxx -370 8.250 8.625 xxxxFBx18708250260xxx -371 8.500 8.875 xxxxFBx18708500260xxx -372 8.750 9.125 xxxxFBx18708750260xxx -373 9.000 9.375 xxxxFBx18709000260xxx -374 9.250 9.625 xxxxFBx18709250260xxx -375 9.500 9.875 xxxxFBx18709500260xxx -376 9.750 10.125 xxxxFBx18709750260xxx -377 10.000 10.375 xxxxFBx18710000260xxx -378 10.500 10.875 xxxxFBx18710500260xxx -379 11.000 11.375 xxxxFBx18711000260xxx -380 11.500 11.875 xxxxFBx18711500260xxx -381 12.000 12.375 xxxxFBx18712000260xxx Dash # Dash # Piston Seal A B Rod or Bore or Part Number Groove Groove Diameter Diameter -382 13.000 13.375 xxxxFBx18713000260xxx -383 14.000 14.375 xxxxFBx18714000260xxx -384 15.000 15.375 xxxxFBx18715000260xxx -385 16.000 16.375 xxxxFBx18716000260xxx -386 17.000 17.375 xxxxFBx18717000260xxx -387 18.000 18.375 xxxxFBx18718000260xxx -388 19.000 19.375 xxxxFBx18719000260xxx -389 20.000 20.375 xxxxFBx18720000260xxx -390 21.000 21.375 xxxxFBx18721000260xxx -391 22.000 22.375 xxxxFBx18722000260xxx -392 23.000 23.375 xxxxFBx18723000260xxx -393 24.000 24.375 xxxxFBx18724000260xxx -394 25.000 25.375 xxxxFBx18725000260xxx -395 26.000 26.375 xxxxFBx18726000260xxx R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.375/0.385" (355 callout) G for Extended heel groove = 0.475/0.485" (450 callout) +.000/ +.003/ -.003 -.000 -401 1.500 2.000 xxxxFBx25001500355xxx -402 1.625 2.125 xxxxFBx25001625355xxx -403 1.750 2.250 xxxxFBx25001750355xxx -404 1.875 2.375 xxxxFBx25001875355xxx -405 2.000 2.500 xxxxFBx25002000355xxx -406 2.125 2.625 xxxxFBx25002125355xxx -407 2.250 2.750 xxxxFBx25002250355xxx -408 2.375 2.875 xxxxFBx25002375355xxx -409 2.500 3.000 xxxxFBx25002500355xxx -410 2.625 3.125 xxxxFBx25002625355xxx -411 2.750 3.250 xxxxFBx25002750355xxx -412 2.875 3.375 xxxxFBx25002875355xxx -413 3.000 3.500 xxxxFBx25003000355xxx -414 3.125 3.625 xxxxFBx25003125355xxx -415 3.250 3.750 xxxxFBx25003250355xxx -416 3.375 3.875 xxxxFBx25003375355xxx
01/15/06
5-15
www.parkerseals.com
G G E E
A B R
A B
R
Rod Seal A B Rod or Bore or Part Number Groove Groove Diameter Diameter R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.375/0.385" (355 callout) G for Extended heel groove = 0.475/0.485" (450 callout) +.000/ +.003/ -.003 -.000 -417 3.500 4.000 xxxxFBx25003500355xxx -418 3.625 4.125 xxxxFBx25003625355xxx -419 3.750 4.250 xxxxFBx25003750355xxx -420 3.875 4.375 xxxxFBx25003875355xxx -421 4.000 4.500 xxxxFBx25004000355xxx -422 4.125 4.625 xxxxFBx25004125355xxx -423 4.250 4.750 xxxxFBx25004250355xxx -424 4.375 4.875 xxxxFBx25004375355xxx -425 4.500 5.000 xxxxFBx25004500355xxx -426 4.625 5.125 xxxxFBx25004625355xxx -427 4.750 5.250 xxxxFBx25004750355xxx -428 4.875 5.375 xxxxFBx25004875355xxx -429 5.000 5.500 xxxxFBx25005000355xxx -430 5.125 5.625 xxxxFBx25005125355xxx -431 5.250 5.750 xxxxFBx25005250355xxx -432 5.375 5.875 xxxxFBx25005375355xxx -433 5.500 6.000 xxxxFBx25005500355xxx -434 5.625 6.125 xxxxFBx25005625355xxx -435 5.750 6.250 xxxxFBx25005750355xxx -436 5.875 6.375 xxxxFBx25005875355xxx -437 6.000 6.500 xxxxFBx25006000355xxx -438 6.250 6.750 xxxxFBx25006250355xxx -439 6.500 7.000 xxxxFBx25006500355xxx -440 6.750 7.250 xxxxFBx25006750355xxx -441 7.000 7.500 xxxxFBx25007000355xxx -442 7.250 7.750 xxxxFBx25007250355xxx -443 7.500 8.000 xxxxFBx25007500355xxx -444 7.750 8.250 xxxxFBx25007750355xxx Dash # Dash # -445 -446 -447 -448 -449 -450 -451 -452 -453 -454 -455 -456 -457 -458 -459 -460 -461 -462 -463 -464 -465 -466 -467 -468 -469 -470 -471 -472 -473 -474 -475 Piston Seal A Rod or Groove Diameter 8.000 8.500 9.000 9.500 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 14.000 14.500 15.000 15.500 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 20.000 21.000 22.000 23.000 24.000 25.000 26.000 B Bore or Groove Diameter 8.500 9.000 9.500 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 14.000 14.500 15.000 15.500 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 20.000 20.500 21.500 22.500 23.500 24.500 25.500 26.500
Part Number xxxxFBx25008000355xxx xxxxFBx25008500355xxx xxxxFBx25009000355xxx xxxxFBx25009500355xxx xxxxFBx25010000355xxx xxxxFBx25010500355xxx xxxxFBx25011000355xxx xxxxFBx25011500355xxx xxxxFBx25012000355xxx xxxxFBx25012500355xxx xxxxFBx25013000355xxx xxxxFBx25013500355xxx xxxxFBx25014000355xxx xxxxFBx25014500355xxx xxxxFBx25015000355xxx xxxxFBx25015500355xxx xxxxFBx25016000355xxx xxxxFBx25016500355xxx xxxxFBx25017000355xxx xxxxFBx25017500355xxx xxxxFBx25018000355xxx xxxxFBx25018500355xxx xxxxFBx25019000355xxx xxxxFBx25019500355xxx xxxxFBx25020000355xxx xxxxFBx25021000355xxx xxxxFBx25022000355xxx xxxxFBx25023000355xxx xxxxFBx25024000355xxx xxxxFBx25025000355xxx xxxxFBx25026000355xxx
01/15/06
5-16
www.parkerseals.com
FlexiSeal Rod & Piston Seals FB Profiles Metric

Metric FB Profiles
All of these FB profiles will fit into the Metric gland sizes on Page 5-18.

Part Number Example

Table 5-8. FB Metric Part Number
M 5 0 2
5
0 5 6 S
FB N
0 4 0 0
0 4 1 5 0
Material Code
Cross-Section
Seal Height Spring Material
Metric Rod & Piston Scraper ID Lip
Gland ID
Canted-Coil Spring Spring Load

All part numbers on the following page call for the standard seal height for pressures below 3000 psi. The heel of a FlexiSeal can be extended to increase extrusion resistance simply by changing the seal height callout in the part number.
M 5 0 2 FB S 0 2 5 0 0 1 4 0 0

0 3 3
Seal Height
M 5 0 2 FB S 0 2 5 0 0 1 4 0 0
0 4 2
Seal Height
01/15/06
5-17
www.parkerseals.com
FB Profiles Metric Gland Dimensions Metric FB Profiles
Table 5-9. FB Metric Gland Dimensions

G E** E** G
A (h9)* B (H9)* A (h9)* R0.38 B (H9)*
R0.38
Rod Seal
Piston Seal
Each of these FlexiSeal profiles were designed to fit into the Metric glands on this page.
CrossSection Callout 0200 0250 0400 0500 0700
Gland Std. Heel Ext. Heel Std. Heel Ext. Heel CrossHeight Height Groove Width (G) Groove Width (G) Section Callout Callout +0.25/-0.00 mm +0.25/-0.00 mm 2.00 mm 021 036 2.39 mm 13.78 mm 2.50 mm 033 042 3.58 mm 14.65 mm 4.00 mm 043 056 4.78 mm 15.97 mm 5.00 mm 066 079 7.14 mm 18.48 mm 7.00 mm 090 114 9.53 mm 12.07 mm
FBC-V
FBS-V
** For ISO Tolerances see Appendix D. ** See Page 2-10 for more on extrusion gap.
Example Part Numbers

FBG-V FBD-V Part Number Hardware ID (A) in mm Hardware OD (B) in mm Groove Width (G) in mm FBS-V Profile M502FBS025001150042SVM 11.50 +.00/-.04 16.50 +.04/-.00 4.65 +0.25/-.00 FBN-C Profile M100FBN050015000066HCL 150.00 +.00/-.10 160.00 +.10/-.00 7.14 +0.25/-.00 FBK-V FBM-V
FBL-V
FBN-H
FBS-H
FBG-H
FBN-C
FBS-C
FBG-C 01/15/06
5-18
www.parkerseals.com
FlexiSeal Rod & Piston Seals FR Profiles MIL-G-5514 Rod

FR Profiles
All FR profiles will fit into the MIL-G-5514 rod gland tables on the following page.

Part Number Example

Table 5-11. FR MIL-G-5514 Rod Part Number
0 5 0 2
5
S
FR C
1 2 5
0 1 3 1 0
1 7 0
O-Ring Groove Rod Chamfered ID & OD Lip
Cantilever Spring


0 5 0 2 F R C 0 6 2 0 1 1 2 5
0 8 3
S V M
Seal Height
0 5 0 2 F R C 0 6 2 0 1 1 2 5
1 4 0
S V M
Seal Height
01/15/07
5-19
www.parkerseals.com
FR Profiles MIL-G-5514 Rod Gland Dimensions FR Profiles

Table 5-12. FR MIL-G-5514 Rod Gland Dimensions
G E
A B
R
Rod Seal
Each of these FlexiSeal profiles were designed to fit into the MIL-G-5514 rod glands on the following pages.
5
FRC-V FRS-V
FRG-V
FRD-V
FRK-V
FRM-V
FRL-V
FRN-H
FRS-H
FRN-C
A B Rod Groove Part Number Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.094/0.104" (083 callout) G for Extended heel groove = 0.149/0.159" (140 callout) +.000/ +.001/ -.001 -.000 -006 0.123 0.235 xxxxFRx06200123083xxx -007 0.154 0.266 xxxxFRx06200154083xxx -008 0.185 0.297 xxxxFRx06200185083xxx -009 0.217 0.329 xxxxFRx06200217083xxx -010 0.248 0.360 xxxxFRx06200248083xxx -011 0.310 0.422 xxxxFRx06200310083xxx -012 0.373 0.485 xxxxFRx06200373083xxx +.000/ +.002/ -.002 -.000 -013 0.435 0.547 xxxxFRx06200435083xxx -014 0.498 0.610 xxxxFRx06200498083xxx -015 0.560 0.672 xxxxFRx06200560083xxx -016 0.623 0.735 xxxxFRx06200623083xxx -017 0.685 0.797 xxxxFRx06200685083xxx -018 0.748 0.860 xxxxFRx06200748083xxx -019 0.810 0.922 xxxxFRx06200810083xxx -020 0.873 0.985 xxxxFRx06200873083xxx -021 0.935 1.047 xxxxFRx06200935083xxx -022 0.998 1.110 xxxxFRx06200998083xxx -023 1.060 1.172 xxxxFRx06201060083xxx -024 1.123 1.235 xxxxFRx06201123083xxx -025 1.185 1.297 xxxxFRx06201185083xxx -026 1.248 1.360 xxxxFRx06201248083xxx -027 1.310 1.422 xxxxFRx06201310083xxx -028 1.373 1.485 xxxxFRx06201373083xxx Dash #
FRG-C
01/15/06
5-20
www.parkerseals.com

Table 5-12. FR MIL-G_5514 Rod Gland Dimensions (Continued)
G E
FR Profiles MIL-G-5514 Rod
A B
R
Rod Seal A B Dash Rod Groove Part Number # Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.141/0.151" (130 callout) G for Extended heel groove = 0.183/0.193" (165 callout) +.000/ +.002/ -.002 -.000 -110 0.373 0.551 xxxxFRx09300373130xxx -111 0.435 0.613 xxxxFRx09300435130xxx -112 0.498 0.676 xxxxFRx09300498130xxx -113 0.560 0.738 xxxxFRx09300560130xxx -114 0.623 0.801 xxxxFRx09300623130xxx -115 0.685 0.863 xxxxFRx09300685130xxx -116 0.748 0.926 xxxxFRx09300748130xxx -117 0.810 0.988 xxxxFRx09300810130xxx -118 0.873 1.051 xxxxFRx09300873130xxx -119 0.935 1.113 xxxxFRx09300935130xxx -120 0.998 1.176 xxxxFRx09300998130xxx -121 1.060 1.238 xxxxFRx09301060130xxx -122 1.123 1.301 xxxxFRx09301123130xxx -123 1.185 1.363 xxxxFRx09301185130xxx -124 1.248 1.426 xxxxFRx09301248130xxx -125 1.310 1.488 xxxxFRx09301310130xxx -126 1.373 1.551 xxxxFRx09301373130xxx -127 1.435 1.613 xxxxFRx09301435130xxx -128 1.498 1.676 xxxxFRx09301498130xxx -129 1.560 1.738 xxxxFRx09301560130xxx -130 1.623 1.801 xxxxFRx09301623130xxx -131 1.685 1.863 xxxxFRx09301685130xxx -132 1.748 1.926 xxxxFRx09301748130xxx -133 1.810 1.988 xxxxFRx09301810130xxx -134 1.873 2.051 xxxxFRx09301873130xxx -135 1.936 2.114 xxxxFRx09301936130xxx -136 1.998 2.176 xxxxFRx09301998130xxx -137 2.061 2.239 xxxxFRx09302061130xxx -138 2.123 2.301 xxxxFRx09302123130xxx -139 2.186 2.364 xxxxFRx09302186130xxx -140 2.248 2.426 xxxxFRx09302248130xxx -141 2.311 2.489 xxxxFRx09302311130xxx -142 2.373 2.551 xxxxFRx09302373130xxx -143 2.436 2.614 xxxxFRx09302436130xxx A B Rod Groove Part Number Diameter Diameter -144 2.498 2.676 xxxxFRx09302498130xxx -145 2.561 2.739 xxxxFRx09302561130xxx -146 2.623 2.801 xxxxFRx09302623130xxx -147 2.686 2.864 xxxxFRx09302686130xxx -148 2.748 2.926 xxxxFRx09302748130xxx -149 2.811 2.989 xxxxFRx09302811130xxx R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.188/0.198" (170 callout) G for Extended heel groove = 0.235/0.245" (220 callout) +.000/ +.002/ -.002 -.000 -210 0.748 0.991 xxxxFRx12500748170xxx -211 0.810 1.053 xxxxFRx12500810170xxx -212 0.873 1.116 xxxxFRx12500873170xxx xxxxFRx12500935170xxx -213 0.935 1.178 xxxxFRx12500998170xxx -214 0.998 1.241 xxxxFRx12501060170xxx -215 1.060 1.303 -216 1.123 1.366 xxxxFRx12501123170xxx -217 1.185 1.428 xxxxFRx12501185170xxx xxxxFRx12501248170xxx -218 1.248 1.491 xxxxFRx12501310170xxx -219 1.310 1.553 -220 1.373 1.616 xxxxFRx12501373170xxx -221 1.435 1.678 xxxxFRx12501435170xxx -222 1.498 1.741 xxxxFRx12501498170xxx -223 1.623 1.866 xxxxFRx12501623170xxx -224 1.748 1.991 xxxxFRx12501748170xxx xxxxFRx12501873170xxx -225 1.873 2.116 xxxxFRx12501998170xxx -226 1.998 2.241 xxxxFRx12502123170xxx -227 2.123 2.366 xxxxFRx12502248170xxx -228 2.248 2.491 xxxxFRx12502373170xxx -229 2.373 2.616 xxxxFRx12502498170xxx -230 2.498 2.741 xxxxFRx12502623170xxx -231 2.623 2.866 xxxxFRx12502748170xxx -232 2.748 2.991 xxxxFRx12502873170xxx -233 2.873 3.116 xxxxFRx12502997170xxx -234 2.997 3.240 xxxxFRx12503122170xxx -235 3.122 3.365 xxxxFRx12503247170xxx -236 3.247 3.490 xxxxFRx12503372170xxx -237 3.372 3.615 Dash # 01/15/07
5-21
www.parkerseals.com

Table 5-12. FR MIL-G-5514 Rod Gland Dimensions (Continued)
G E
A B
R
Rod Seal A B Dash Rod Groove Part Number # Diameter Diameter R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.188/0.198" (170 callout) G for Extended heel groove = 0.235/0.245" (220 callout) +.000/ +.002/ -.002 -.000 -238 3.497 3.740 xxxxFRx12503497170xxx -239 3.622 3.865 xxxxFRx12503622170xxx xxxxFRx12503747170xxx -240 3.747 3.990 xxxxFRx12503872170xxx -241 3.872 4.115 xxxxFRx12503997170xxx -242 3.997 4.240 xxxxFRx12504122170xxx -243 4.122 4.365 xxxxFRx12504247170xxx -244 4.247 4.490 xxxxFRx12504372170xxx -245 4.372 4.615 xxxxFRx12504497170xxx -246 4.497 4.740 xxxxFRx12504622170xxx -247 4.622 4.865 R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.281/0.291" (260 callout) G for Extended heel groove = 0.334/0.344" (310 callout) +.000/ +.002/ -.002 -.000 -325 1.498 1.870 xxxxFRx18701498260xxx -326 1.623 1.995 xxxxFRx18701623260xxx -327 1.748 2.120 xxxxFRx18701748260xxx -328 1.873 2.245 xxxxFRx18701873260xxx -329 1.998 2.370 xxxxFRx18701998260xxx -330 2.123 2.495 xxxxFRx18702123260xxx -331 2.248 2.620 xxxxFRx18702248260xxx -332 2.373 2.745 xxxxFRx18702373260xxx -333 2.498 2.870 xxxxFRx18702498260xxx -334 2.623 2.995 xxxxFRx18702623260xxx -335 2.748 3.120 xxxxFRx18702748260xxx -336 2.873 3.245 xxxxFRx18702873260xxx -337 2.997 3.369 xxxxFRx18702997260xxx -338 3.122 3.494 xxxxFRx18703122260xxx -339 3.247 3.619 xxxxFRx18703247260xxx -340 3.372 3.744 xxxxFRx18703372260xxx A B Rod Groove Part Number Diameter Diameter -341 3.497 3.869 xxxxFRx18703497260xxx -342 3.622 3.994 xxxxFRx18703622260xxx -343 3.747 4.119 xxxxFRx18703747260xxx -344 3.872 4.244 xxxxFRx18703872260xxx -345 3.997 4.369 xxxxFRx18703997260xxx -346 4.122 4.494 xxxxFRx18704122260xxx -347 4.247 4.619 xxxxFRx18704247260xxx -348 4.372 4.744 xxxxFRx18704372260xxx -349 4.497 4.869 xxxxFRx18704497260xxx R = 0.015" max. radius E = 0.004" max. G for Standard heel groove = 0.375/0.385" (355 callout) G for Extended heel groove = 0.475/0.485" (450 callout) +.000/ +.003/ -.003 -.000 -425 4.497 4.974 xxxxFRx25004497355xxx -426 4.622 5.099 xxxxFRx25004622355xxx -427 4.747 5.224 xxxxFRx25004747355xxx -428 4.872 5.349 xxxxFRx25004872355xxx -429 4.997 5.474 xxxxFRx25004997355xxx -430 5.122 5.599 xxxxFRx25005122355xxx -431 5.247 5.724 xxxxFRx25005247355xxx -432 5.372 5.849 xxxxFRx25005372355xxx -433 5.497 5.974 xxxxFRx25005497355xxx -434 5.622 6.099 xxxxFRx25005622355xxx -435 5.747 6.224 xxxxFRx25005747355xxx -436 5.872 6.349 xxxxFRx25005872355xxx -437 5.997 6.474 xxxxFRx25005997355xxx -438 6.247 6.724 xxxxFRx25006247355xxx -439 6.497 6.974 xxxxFRx25006497355xxx -440 6.747 7.224 xxxxFRx25006747355xxx -441 6.997 7.474 xxxxFRx25006997355xxx -442 7.247 7.724 xxxxFRx25007247355xxx -443 7.497 7.974 xxxxFRx25007497355xxx -444 7.747 8.224 xxxxFRx25007747355xxx -445 7.997 8.474 xxxxFRx25007997355xxx -446 8.497 8.974 xxxxFRx25008497355xxx Dash #
01/15/07
5-22
www.parkerseals.com

Table 5-12. FR MIL-G-5514 Rod Gland Dimensions (Continued)
G E
A B
R
Rod Seal A B Dash Rod Groove Part Number # Diameter Diameter R = 0.015" max. radius E = 0.004" max. G for Standard heel groove = 0.375/0.385" (355 callout) G for Extended heel groove = 0.475/0.485" (450 callout) +.000/ +.004/ -.003 -.000 -447 8.997 9.474 xxxxFRx25008997355xxx -448 9.497 9.974 xxxxFRx25009497355xxx -449 9.997 10.474 xxxxFRx25009997355xxx -450 10.497 10.974 xxxxFRx25010497355xxx -451 10.997 11.474 xxxxFRx25010997355xxx -452 11.497 11.974 xxxxFRx25011497355xxx Dash # -453 -454 -455 -456 -457 -458 -459 -460 A Rod Diameter 11.997 12.497 12.997 13.497 13.997 14.497 14.997 15.497 B Groove Diameter 12.474 12.974 13.474 13.974 14.474 14.974 14.474 15.974 Part Number xxxxFRx25011997355xxx xxxxFRx25012497355xxx xxxxFRx25012997355xxx xxxxFRx25013497355xxx xxxxFRx25013997355xxx xxxxFRx25014497355xxx xxxxFRx25014997355xxx xxxxFRx25015497355xxx
01/15/06
5-23
www.parkerseals.com
FlexiSeal Rod & Piston Seals FP Profiles MIL-G-5514 Piston

FP Profiles
All FP profiles will fit into the MIL-G-5514 piston gland tables on the following pages.

Groove Width
Part Number Example

Table 5-14. FP MIL-G-5514 Piston Part Number
0 5 0 2
Seal Height
FP C
1 2 5
0 1 3 1 0
1 7 0
O-Ring Groove Piston Chamfered ID & OD Lip
Cantilever Spring

0 5 0 2 F P C 0 6 2 0 1 3 1 6

0 8 3
S V M
Seal Height
0 5 0 2 F P C 0 6 2 0 1 3 1 6
1 4 0
S V M
Seal Height
01/15/07
5-24
www.parkerseals.com
FlexiSeal Rod & Piston Seals Gland Dimensions FP Profiles

Table 5-15. FP MIL-G-5514 Piston Gland Dimensions
FP Profiles MIL-G-5514 Piston
G E
A B R
Piston Seal
Each of these FlexiSeal profiles were designed to fit into the MIL-G-5514 piston glands on the following pages.
FPC-V
FPS-V
FPG-V
FPD-V
FPK-V
FPM-V
FPL-V
FPN-H
FPG-H
FPN-C
A B Groove Bore Part Number Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.094/0.104" (083 callout) G for Extended heel groove = 0.149/0.159" (140 callout) +.000/ +.001/ -.001 -.000 -006 0.123 0.235 xxxxFPx06200123083xxx -007 0.154 0.266 xxxxFPx06200154083xxx -008 0.185 0.297 xxxxFPx06200185083xxx -009 0.217 0.329 xxxxFPx06200217083xxx -010 0.248 0.360 xxxxFPx06200248083xxx -011 0.310 0.422 xxxxFPx06200310083xxx -012 0.373 0.485 xxxxFPx06200373083xxx +.000/ +.002/ -.002 -.000 -013 0.438 0.550 xxxxFPx06200438083xxx -014 0.501 0.613 xxxxFPx06200501083xxx -015 0.563 0.675 xxxxFPx06200563083xxx -016 0.626 0.738 xxxxFPx06200626083xxx -017 0.688 0.800 xxxxFPx06200688083xxx -018 0.751 0.863 xxxxFPx06200751083xxx -019 0.813 0.925 xxxxFPx06200813083xxx -020 0.879 0.991 xxxxFPx06200879083xxx -021 0.941 1.053 xxxxFPx06200941083xxx -022 1.004 1.116 xxxxFPx06201004083xxx -023 1.066 1.178 xxxxFPx06201066083xxx -024 1.129 1.241 xxxxFPx06201129083xxx -025 1.191 1.303 xxxxFPx06201191083xxx -026 1.254 1.366 xxxxFPx06201254083xxx -027 1.316 1.428 xxxxFPx06201316083xxx -028 1.379 1.491 xxxxFPx06201379083xxx Dash #
FPS-C
01/15/06
5-25
www.parkerseals.com

Table 5-15. FP MIL-G-5514 Piston Gland Dimensions (Continued)
G E
A B R
Piston Seal A B Dash Groove Bore Part Number # Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for Standard heel groove = 0.141/0.151" (130 callout) G for Extended heel groove = 0.183/0.193" (165 callout) +.000/ +.002/ -.002 -.000 -110 0.372 0.550 xxxxFPx09300372130xxx -111 0.435 0.613 xxxxFPx09300435130xxx -112 0.497 0.675 xxxxFPx09300497130xxx -113 0.560 0.738 xxxxFPx09300560130xxx -114 0.622 0.800 xxxxFPx09300622130xxx -115 0.685 0.863 xxxxFPx09300685130xxx -116 0.747 0.925 xxxxFPx09300747130xxx -117 0.813 0.991 xxxxFPx09300813130xxx -118 0.875 1.053 xxxxFPx09300875130xxx -119 0.938 1.116 xxxxFPx09300938130xxx -120 1.000 1.178 xxxxFPx09301000130xxx -121 1.063 1.241 xxxxFPx09301063130xxx -122 1.125 1.303 xxxxFPx09301125130xxx -123 1.188 1.366 xxxxFPx09301188130xxx -124 1.250 1.428 xxxxFPx09301250130xxx -125 1.313 1.491 xxxxFPx09301313130xxx -126 1.375 1.553 xxxxFPx09301375130xxx -127 1.438 1.616 xxxxFPx09301438130xxx -128 1.500 1.678 xxxxFPx09301500130xxx -129 1.563 1.741 xxxxFPx09301563130xxx -130 1.627 1.805 xxxxFPx09301627130xxx -131 1.689 1.867 xxxxFPx09301689130xxx -132 1.752 1.930 xxxxFPx09301752130xxx -133 1.814 1.992 xxxxFPx09301814130xxx -134 1.877 2.055 xxxxFPx09301877130xxx -135 1.940 2.118 xxxxFPx09301940130xxx -136 2.002 2.180 xxxxFPx09302002130xxx -137 2.065 2.243 xxxxFPx09302065130xxx -138 2.127 2.305 xxxxFPx09302127130xxx -139 2.190 2.368 xxxxFPx09302190130xxx -140 2.252 2.430 xxxxFPx09302252130xxx -141 2.315 2.493 xxxxFPx09302315130xxx A B Groove Bore Part Number Diameter Diameter -142 2.377 2.555 xxxxFPx09302377130xxx -143 2.440 2.618 xxxxFPx09302440130xxx -144 2.502 2.680 xxxxFPx09302502130xxx -145 2.565 2.743 xxxxFPx09302565130xxx -146 2.627 2.805 xxxxFPx09302627130xxx -147 2.690 2.868 xxxxFPx09302690130xxx -148 2.752 2.930 xxxxFPx09302752130xxx -149 2.815 2.993 xxxxFPx09302815130xxx R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.188/0.198" (170 callout) G for Extended heel groove = 0.235/0.245" (220 callout) +.000/ +.002/ -.002 -.000 -210 0.748 0.991 xxxxFPx12500748170xxx -211 0.810 1.053 xxxxFPx12500810170xxx xxxxFPx12500873170xxx -212 0.873 1.116 xxxxFPx12500935170xxx -213 0.935 1.178 xxxxFPx12500998170xxx -214 0.998 1.241 xxxxFPx12501060170xxx -215 1.060 1.303 xxxxFPx12501123170xxx -216 1.123 1.366 xxxxFPx12501185170xxx -217 1.185 1.428 xxxxFPx12501248170xxx -218 1.248 1.491 xxxxFPx12501310170xxx -219 1.310 1.553 xxxxFPx12501373170xxx -220 1.373 1.616 xxxxFPx12501435170xxx -221 1.435 1.678 xxxxFPx12501498170xxx -222 1.498 1.741 -223 1.624 1.867 xxxxFPx12501624170xxx xxxxFPx12501749170xxx -224 1.749 1.992 xxxxFPx12501875170xxx -225 1.875 2.118 xxxxFPx12502000170xxx -226 2.000 2.243 -227 2.125 2.368 xxxxFPx12502125170xxx xxxxFPx12502250170xxx -228 2.250 2.493 xxxxFPx12502375170xxx -229 2.375 2.618 -230 2.500 2.743 xxxxFPx12502500170xxx -231 2.625 2.868 xxxxFPx12502625170xxx -232 2.750 2.993 xxxxFPx12502750170xxx Dash #
01/15/07
5-26
www.parkerseals.com

G E
A B R
Piston Seal A B Dash Groove Bore Part Number # Diameter Diameter R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.188/0.198" (170 callout) G for Extended heel groove = 0.235/0.245" (220 callout) +.000/ +.002/ -.002 -.000 -233 2.875 3.118 xxxxFPx12502875170xxx xxxxFPx12503000170xxx -234 3.000 3.243 xxxxFPx12503125170xxx -235 3.125 3.368 xxxxFPx12503250170xxx -236 3.250 3.493 xxxxFPx12503375170xxx -237 3.375 3.618 xxxxFPx12503500170xxx -238 3.500 3.743 xxxxFPx12503625170xxx -239 3.625 3.868 xxxxFPx12503750170xxx -240 3.750 3.993 xxxxFPx12503875170xxx -241 3.875 4.118 xxxxFPx12504000170xxx -242 4.000 4.243 xxxxFPx12504125170xxx -243 4.125 4.368 xxxxFPx12504250170xxx -244 4.250 4.493 xxxxFPx12504375170xxx -245 4.375 4.618 xxxxFPx12504500170xxx -246 4.500 4.743 xxxxFPx12504625170xxx -247 4.625 4.868 R = 0.015" max. radius E = 0.003" max. G for Standard heel groove = 0.281/0.291" (260 callout) G for Extended heel groove = 0.334/0.344" (310 callout) +.000/ +.002/ -.002 -.000 -325 1.495 1.867 xxxxFPx18701495260xxx -326 1.620 1.992 xxxxFPx18701620260xxx -327 1.746 2.118 xxxxFPx18701746260xxx -328 1.871 2.243 xxxxFPx18701871260xxx -329 1.996 2.368 xxxxFPx18701996260xxx -330 2.121 2.493 xxxxFPx18702121260xxx -331 2.246 2.618 xxxxFPx18702246260xxx -332 2.371 2.743 xxxxFPx18702371260xxx -333 2.496 2.868 xxxxFPx18702496260xxx -334 2.621 2.993 xxxxFPx18702621260xxx -335 2.746 3.118 xxxxFPx18702746260xxx -336 2.871 3.243 xxxxFPx18702871260xxx A B Groove Bore Part Number Diameter Diameter -337 2.996 3.368 xxxxFPx18702996260xxx -338 3.121 3.493 xxxxFPx18703121260xxx -339 3.246 3.618 xxxxFPx18703246260xxx -340 3.371 3.743 xxxxFPx18703371260xxx -341 3.496 3.868 xxxxFPx18703496260xxx -342 3.621 3.993 xxxxFPx18703621260xxx -343 3.746 4.118 xxxxFPx18703746260xxx -344 3.871 4.243 xxxxFPx18703871260xxx -345 3.996 4.368 xxxxFPx18703996260xxx -346 4.121 4.493 xxxxFPx18704121260xxx -347 4.246 4.618 xxxxFPx18704246260xxx -348 4.371 4.743 xxxxFPx18704371260xxx -349 4.496 4.868 xxxxFPx18704496260xxx R = 0.015" max. radius E = 0.004" max. G for Standard heel groove = 0.375/0.385" (355 callout) G for Extended heel groove = 0.475/0.485" (450 callout) +.000/ +.002/ -.003 -.000 -425 4.497 4.974 xxxxFPx25004497355xxx -426 4.622 5.099 xxxxFPx25004622355xxx -427 4.747 5.224 xxxxFPx25004747355xxx -428 4.872 5.349 xxxxFPx25004872355xxx -429 4.997 5.474 xxxxFPx25004997355xxx -430 5.122 5.599 xxxxFPx25005122355xxx -431 5.247 5.724 xxxxFPx25005247355xxx -432 5.372 5.849 xxxxFPx25005372355xxx -433 5.497 5.974 xxxxFPx25005497355xxx -434 5.622 6.099 xxxxFPx25005622355xxx -435 5.747 6.224 xxxxFPx25005747355xxx -436 5.872 6.349 xxxxFPx25005872355xxx -437 5.997 6.474 xxxxFPx25005997355xxx -438 6.247 6.724 xxxxFPx25006247355xxx -439 6.497 6.974 xxxxFPx25006497355xxx -440 6.747 7.224 xxxxFPx25006747355xxx -441 6.997 7.474 xxxxFPx25006997355xxx -442 7.247 7.724 xxxxFPx25007247355xxx Dash #
01/15/07
5-27
www.parkerseals.com

G E
A B R
Piston Seal A B Dash Groove Bore Part Number # Diameter Diameter R = 0.015" max. radius E = 0.004" max. G for Standard heel groove = 0.375/0.385" (355 callout) G for Extended heel groove = 0.475/0.485" (450 callout) +.000/ +.003 -.003 /-.000 -443 7.497 7.974 xxxxFPx25007497355xxx -444 7.747 8.224 xxxxFPx25007747355xxx -445 7.997 8.474 xxxxFPx25007997355xxx -446 8.497 8.974 xxxxFPx25008497355xxx +.000/+.004/.003 .000 -447 8.997 9.474 xxxxFPx25008997355xxx -448 9.497 9.974 xxxxFPx25009497355xxx -449 9.997 10.474 xxxxFPx25009997355xxx Dash # -450 -451 -452 -453 -454 -455 -456 -457 -458 -459 -460 A Groove Diameter 10.497 10.997 11.497 11.997 12.497 12.997 13.497 13.997 14.497 14.997 15.497 B Bore Diameter 10.974 11.474 11.974 12.474 12.974 13.474 13.974 14.474 14.974 14.474 15.974 Part Number xxxxFPx25010497355xxx xxxxFPx25010997355xxx xxxxFPx25011497355xxx xxxxFPx25011997355xxx xxxxFPx25012497355xxx xxxxFPx25012997355xxx xxxxFPx25013497355xxx xxxxFPx25013997355xxx xxxxFPx25014497355xxx xxxxFPx25014997355xxx xxxxFPx25015497355xxx
01/15/06
5-28
www.parkerseals.com
FlexiSeal Face Seals Introduction

Contents
Engineering . . . . . . . . . . . . . . . . . Materials . . . . . . . . . . . . . . . . . . . Product Offering . . . . . . . . . . . . . FlexiSeal Face Seal FE Profiles External Pressure Face Seals . . . . . . . 6-8 6-2 6-3 6-4
Internal/external pressure face seals drop in like O-rings.
FI Profiles Internal Pressure Face Seals . . . . . . . 6-14 FE & FI Profiles Metric . . . . . . . . . . . . . . . . . . . 6-20
Creating a face seal gland can be as simple as cutting a groove in the face of the hardware and dropping the FlexiSeal into it like an O-ring. The FlexiSeal is designed to have a clearance fit on the non-pressure side of the seal so it will press easily into the groove. Of course it is not necessary to have a completely enclosed gland wall on the pressure side since the forces will never push the seal against that side of the groove. Face seals can be configured to seal internal pressure like in a pressurized chemical vat, or as an external seal like in a vacuum chamber.
Applications
FlexiSeal Face Seals
The FlexiSeal Face Seals advantages over conventional elastomeric seals make it ideal for many applications including:
Chemical Vats Dynamic Rotary Dust Excluders Pressurized Beverage Containers Quick Disconnects Scroll Compressors Vacuum Chambers Many more
Internal Pressure
Markets
FlexiSeal Face Seals are easy to install and suitable for the extreme conditions of many markets including:
Aerospace Chemical Process Appliances Machine Tools Medical Pharmaceutical Food & Beverage Oil & Gas Semiconductor Plastics
External Pressure
Internal Face Seal
External Face Seal 01/15/06
6-1
www.parkerseals.com
FlexiSeal Face Seals Engineering

Face seals are used in applications involving high pressures and temperatures, cryogenic fluids, corrosive media and other service conditions which exceed the limits of conventional elastomeric seals. Face seals are designed for either internal or external pressure. For internal pressure, the open side of the spring cavity faces the inside of the vessel. Fluid pressure actuates the seal lips. For external pressure, the spring cavity faces out (see illustration on Page 6-1).
Extrusion Gap
In face seal hardware, the extrusion gap is usually zero. It can be as much as 0.003 inches without affecting the seals rated pressure. When the lifting force due to fluid pressure exceeds the holding force of the vessels flange bolts, the top of the gland can separate from the cylinder, increasing the extrusion gap. In such applications, a separate backup ring is recommended to fill the gap.
Extrusion Gap
Gland Design
Face seal glands are similar to O-ring glands. The inner wall of the internal face seal gland and the outer wall of the external face seal gland are not required to retain the seal. The FlexiSeal Face Seal maintains its own shape and wont move out of its gland.
Excessive fluid pressure can cause an extrusion gap
Figure 6-1. Fluid Pressure Causes Extrusion Gap
Spring Load
For static sealing, use a medium or heavy spring load. In dynamic service the medium load is usually preferred. In cryogenic service the seal material becomes harder and does not conform to the mating surface as readily; to compensate for the increased hardness of the seal jacket, a heavier spring load should be selected. Light load spring can be used when low closure force is required.
Surface Finish
The typical surface finish for a static face seal gland is 16 32 in Ra. A smoother finish may be needed when sealing light gases or cryogenic fluids, or in dynamic service. General surface finish requirements are discussed in further detail on Page 2-9.
Design Selection
Complete the following steps to select a face seal design. 1. Choose a seal design category based on the type of spring used V Series with cantilever spring, C Series with canted-coil spring, or H Series with helical ribbon spring. For details on the different spring types and seal design concepts, refer to Pages 2-12 through 2-17. 2. Select the seal cross-section and diameter using the gland tables beginning on Page 6-9. 3. Select the jacket and spring materials with reference to Tab 3.
01/15/06
6-2
www.parkerseals.com
FlexiSeal Face Seals Materials

The most popular PTFE fillers used for FlexiSeal Face Seal products are graphite, carbon fiber and aromatic polyester. Virgin PTFE is also one of the most common material choices for face seals, especially when chemical compatibility is critical. 0100 Virgin PTFE
Virgin PTFE has the best chemical resistance and lowest coefficient of friction of any of the material choices. Its purity also makes it suitable for food contact applications. 0301 Graphite Filled Graphite filled PTFE has extremely low coefficient of friction due to the low friction characteristics of graphite. Graphite is chemically inert. Graphite imparts excellent wear properties and high PV to PTFE. 0502 Carbon Fiber Filled Carbon fiber lowers creep, increases flex and compressive modulus and raises hardness. Coefficient of thermal expansion is lowered and thermal conductivity is higher for compounds of carbon fiber filled PTFE. Ideal for automotive applications in shock absorbers and water pumps. 0601 Aromatic Polyester Filled Aromatic polyester is excellent for high temperatures and has excellent wear resistance against soft, dynamic surfaces. Not recommended for sealing applications involving steam.
A number of other fillers are used in combination with PTFE, and non-PTFE compounds are available. More information on these materials and their properties is available in Tab 3. For best results for your sealing applications, please contact the EPS Division Application Engineering team at (801) 972-3000.
01/15/06
6-3
www.parkerseals.com
FlexiSeal Face Seals Product Offering

Decision Trees
The key application considerations for static & intermittent dynamic face seal applications are closure force requirements, motion, media abrasiveness and pressure direction. Helical springs are recommended when the seals are mostly static, while canted-coil springs are recommended for dynamic applications. The decision trees in this guide are to be used as an engineering guide only. Often several other parameters must be considered to optimize seal design. Contact Parkers PTFE Engineering Team for confirmation of your choice or further recommendations. Parker also recommends that any seal be tested in the application conditions before releasing for production.
Static & Intermittent Dynamic Face Seal Applications
Pressure?
INT EXT
FIN-C Pages 6-14 and 6-20
FEN-C Pages 6-8 and 6-20 Low Closure Force Needed?
Yes No
Pressure?
INT EXT
FIN-H Pages 6-14 and 6-20
Static? Slow Dynamic?
FEN-H Pages 6-8 and 6-20
Pressure?
INT EXT
FID-V Pages 6-14 and 6-20
Abrasive Media?
FED-V Pages 6-8 and 6-20

Yes No
Pressure?
INT EXT
FIC-V FIK-V Pages 6-14 and 6-20
FEC-V FEK-V Pages 6-8 and 6-20
01/15/06
6-4
www.parkerseals.com
FlexiSeal Face Seals Part Number Nomenclature FlexiSeal Face Seal

Table 6-1. FlexiSeal Face Seal Part Number Nomenclature
Product Offering
English 0 3 0 1 FE N 1 2 5 0 1 2 5 0 1 7 0 S C L
Gland Cross-Section Examples: 062 = 0.062" 093 = 0.093" 125 = 0.125" 187 = 0.187" 250 = 0.250" 4-Digit Material Code Examples: 0301 = Graphite Filled 0301 = PTFE 0502 = Carbon Fiber 0301 = Filled PTFE Lip Style Designation N = Default/No Lip Style C = Chamfered ID & OD D = Dual Scraper K = Beaded ID & OD FlexiSeal Gland Type Classification FE = External Face Seal FI = Internal Face Seal
Seal Height Designation Examples: 083 = 0.083" 130 = 0.130" 170 = 0.170" 260 = 0.260" 355 = 0.355" Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
Gland Inside Diameter (Groove Diameter) Examples: 00500 = 0.500" 02500 = 2.500" 11000 = 11.000"
Metric M 3 0 1 FE N 0 4 0 0 2 2 5 0 0 0 4 3 S C L
Gland Cross-Section Examples: 0200 = 2.00 mm 0250 = 2.50 mm 0400 = 4.00 mm 0500 = 5.00 mm 0700 = 7.00 mm 4-Digit Material Code Lip Style Designation Examples: N = Default Lip Style M301 = Graphite Filled C = Chamfered ID & OD M301 = PTFE D = Dual Scraper M502 = Carbon Fiber K = Beaded ID & OD M301 = Filled PTFE (M indicates metric) FlexiSeal Gland Type Classification FE = External Face Seal FI = Internal Face Seal
Seal Height Designation Examples: 021 = 2.1 mm 033 = 3.3 mm 043 = 4.3 mm 066 = 6.6 mm 090 = 9.0 mm Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
Gland Inside Diameter (Groove Diameter) Examples: 00800 = 88.00 mm 01150 = 11.50 mm 06500 = 65.00 mm
FEC-V
FED-V
FEK-V
FEN-C
FEN-H
FIC-V
FID-V
FIK-V
FIN-C
FIN-H
01/15/07
6-5
www.parkerseals.com

Profile Features Recommended Applications Seals external pressure. High sealability and closure force. Available as Standard in High Pressure Extended Heel (up to 10,000 psi) No Friction Rating High Closure Force Low Pressure Sealability Excellent
Good in Abrasive Media No
Gland Dimension Table Location Pages 6-8, 6-20
Available in Mil-G-5514 Glands No
FEN-H
Lips Facing Out, Rounded Lips, Helical Spring
FEC-V
Lips Facing Out, Chamfered Lips, Cantilever Spring Lips Facing Out, Scraper Lips, Cantilever Spring
Seals external No pressure. Good sealability for non-abrasive fluids.
Medium Closure Force
Very Good
No
Pages 6-8, 6-20
No
FED-V
Seals external No pressure. Good sealability for abrasive fluids.
Very Good
Yes
Pages 6-8, 6-20
No
FEK-V
Lips Facing Out, Beaded Lips, Cantilever Spring
Seals external No pressure. Good sealability for non-abrasive fluids. Rounded like O-ring. Seals external No pressure. Low closure force for non-abrasive fluids.
Very Good
No
Pages 6-8, 6-20
No
FEN-C
Lips Facing Out, BackBeveled Lips, Canted-Coil Spring
Low Closure Force
Good
No
Pages 6-8, 6-20
No
01/15/07
6-6
www.parkerseals.com

Profile Features Recommended Applications Available as Standard in High Pressure Extended Heel (up to 10,000 psi) No Friction Rating High Closure Force Low Pressure Sealability Excellent Good in Abrasive Media No
Product Offering
Gland Dimension Available in Mil-G-5514 Table Glands Location Pages 6-14, No 6-20
FIN-H
Lips Facing In, Seals internal Rounded Lips, pressure. High Helical Spring sealability and closure force.
FIC-V
Lips Facing In, Chamfered Lips, Cantilever Spring
Seals internal No pressure. Good sealability for non-abrasive fluids.
Very Good
No
Pages 6-14, No 6-20
FID-V
Lips Facing In, Scraper Lips, Cantilever Spring
Seals internal No pressure. Good sealability for abrasive fluids.
Very Good
Yes
Pages 6-14, No 6-20
FIK-V
Lips Facing In, Beaded Lips, Cantilever Spring
No Seals internal pressure. Good sealability for non-abrasive fluids. Rounded like O-ring. Seals internal No pressure. Low closure force for non-abrasive fluids.
Very Good
No
Pages 6-14, No 6-20
6
Low Closure Force Good No Pages 6-14, No 6-20
FIN-C
Lips Facing In, Back-Beveled Lips, CantedCoil Spring
01/15/06
6-7
www.parkerseals.com
FlexiSeal Face Seals FE Profiles External Pressure

FE Profiles
FE FlexiSeal External Pressure Face Seals are designed so that the spring cavity faces out.
Hardware Configurations/Installation, see Page 2-3 Surface Finish and Hardness, see Page 2-9 Extrusion Gaps and High Pressure, see Page 2-10 Spring Choices, see Page 2-12 Lip Shapes, see Page 2-16 Face Seal Gland Considerations, see Page 6-2 Shaft Misalignment Issues, see Page 2-19
External Pressure Face Seals
Part Number Example

Table 6-3. FE External Pressure Part Number
6
External Pressure
0 3 0 1
FE N
1 2 5
0 1 2 5 0
1 7 0
External Face Seal Default Lip Style
Helical Spring
01/15/07
6-8
www.parkerseals.com
FlexiSeal Face Seals Gland Dimensions FE Profiles

Table 6-4. FE External Pressure Gland Dimensions
FE Profiles External Pressure
B Ref. A G
L R External Pressure
Each of these FlexiSeal profiles were designed to fit into either the Inch/Fractional external pressure face seal glands on the following pages or the Metric glands on Page 6-20.
FEN-H
FEC-V
FED-V
FEK-V
FEN-C
B Min. Gland OD R = 0.015" max. radius L = 0.056/0.058" G = 0.094" minimum +.000/ -.005 -008 0.187 0.375 -009 0.218 0.406 -010 0.250 0.437 -011 0.312 0.500 -012 0.375 0.562 -013 0.437 0.625 -014 0.500 0.687 -015 0.562 0.750 -016 0.625 0.812 -017 0.687 0.875 -018 0.750 0.937 -019 0.812 1.000 -020 0.875 1.062 -021 0.937 1.125 -022 1.000 1.187 -023 1.062 1.250 -024 1.125 1.312 -025 1.187 1.375 -026 1.250 1.437 -027 1.312 1.500 -028 1.375 1.562 -029 1.500 1.687 -030 1.625 1.812 -031 1.750 1.937 -032 1.875 2.062 -033 2.000 2.187 -034 2.125 2.312 -035 2.250 2.437 -036 2.375 2.562 -037 2.500 2.687 -038 2.625 2.812 -039 2.750 2.937 Dash # A Gland ID
Part Number
xxxxFEx06200187083xxx xxxxFEx06200218083xxx xxxxFEx06200250083xxx xxxxFEx06200312083xxx xxxxFEx06200375083xxx xxxxFEx06200437083xxx xxxxFEx06200500083xxx xxxxFEx06200562083xxx xxxxFEx06200625083xxx xxxxFEx06200687083xxx xxxxFEx06200750083xxx xxxxFEx06200812083xxx xxxxFEx06200875083xxx xxxxFEx06200937083xxx xxxxFEx06201000083xxx xxxxFEx06201062083xxx xxxxFEx06201125083xxx xxxxFEx06201187083xxx xxxxFEx06201250083xxx xxxxFEx06201312083xxx xxxxFEx06201375083xxx xxxxFEx06201500083xxx xxxxFEx06201625083xxx xxxxFEx06201750083xxx xxxxFEx06201875083xxx xxxxFEx06202000083xxx xxxxFEx06202125083xxx xxxxFEx06202250083xxx xxxxFEx06202375083xxx xxxxFEx06202500083xxx xxxxFEx06202625083xxx xxxxFEx06202750083xxx 01/15/06
6-9
www.parkerseals.com

Table 6-4. FE External Pressure Gland Dimensions (Continued)
B Ref. A G
L R External Pressure B Dash A Min. # Gland ID Gland OD R = 0.015" max. radius L = 0.056/0.058" G = 0.094" minimum +.001/ -.005 -040 2.875 3.062 -041 3.000 3.187 -042 3.250 3.437 -043 3.500 3.687 -044 3.750 3.937 -045 4.000 4.187 R = 0.015" max. radius L = 0.089/0.091" G = 0.141" minimum +.001/ -.005 -110 0.375 0.657 -111 0.437 0.719 -112 0.500 0.782 -113 0.562 0.844 -114 0.625 0.907 -115 0.687 0.969 -116 0.750 1.032 -117 0.812 1.094 -118 0.875 1.157 -119 0.937 1.219 -120 1.000 1.282 -121 1.062 1.344 -122 1.125 1.407 -123 1.187 1.469 -124 1.250 1.532 -125 1.312 1.594 -126 1.375 1.657 -127 1.437 1.719 -128 1.500 1.782 -129 1.562 1.844 -130 1.625 1.907 -131 1.687 1.969 Part Number Dash # -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -151 -152 -153 -154 -155 -156 -157 -158 -159 -160 -161 -162 -163 -164 -165 A Gland ID 1.750 1.812 1.875 1.937 2.000 2.062 2.125 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 3.000 3.250 3.500 3.750 4.000 4.250 4.500 4.750 5.000 5.250 5.500 5.750 6.000 6.250 6.500 B Min. Gland OD 2.032 2.094 2.157 2.219 2.282 2.344 2.407 2.469 2.532 2.594 2.657 2.719 2.782 2.844 2.907 2.969 3.032 3.094 3.157 3.282 3.532 3.782 4.032 4.282 4.532 4.872 5.032 5.282 5.532 5.782 6.032 6.282 6.532 6.782 Part Number xxxxFEx09301750130xxx xxxxFEx09301812130xxx xxxxFEx09301875130xxx xxxxFEx09301937130xxx xxxxFEx09302000130xxx xxxxFEx09302062130xxx xxxxFEx09302125130xxx xxxxFEx09302187130xxx xxxxFEx09302250130xxx xxxxFEx09302312130xxx xxxxFEx09302375130xxx xxxxFEx09302437130xxx xxxxFEx09302500130xxx xxxxFEx09302562130xxx xxxxFEx09302625130xxx xxxxFEx09302687130xxx xxxxFEx09302750130xxx xxxxFEx09302812130xxx xxxxFEx09302875130xxx xxxxFEx09303000130xxx xxxxFEx09303250130xxx xxxxFEx09303500130xxx xxxxFEx09303750130xxx xxxxFEx09304000130xxx xxxxFEx09304250130xxx xxxxFEx09304500130xxx xxxxFEx09304750130xxx xxxxFEx09305000130xxx xxxxFEx09305250130xxx xxxxFEx09305500130xxx xxxxFEx09305750130xxx xxxxFEx09306000130xxx xxxxFEx09306250130xxx xxxxFEx09306500130xxx
xxxxFEx06202875083xxx xxxxFEx06203000083xxx xxxxFEx06203250083xxx xxxxFEx06203500083xxx xxxxFEx06203750083xxx xxxxFEx06204000083xxx
xxxxFEx09300375130xxx xxxxFEx09300437130xxx xxxxFEx09300500130xxx xxxxFEx09300562130xxx xxxxFEx09300625130xxx xxxxFEx09300687130xxx xxxxFEx09300750130xxx xxxxFEx09300812130xxx xxxxFEx09300875130xxx xxxxFEx09300937130xxx xxxxFEx09301000130xxx xxxxFEx09301062130xxx xxxxFEx09301125130xxx xxxxFEx09301187130xxx xxxxFEx09301250130xxx xxxxFEx09301312130xxx xxxxFEx09301375130xxx xxxxFEx09301437130xxx xxxxFEx09301500130xxx xxxxFEx09301562130xxx xxxxFEx09301625130xxx xxxxFEx09301687130xxx
01/15/06
6-10
www.parkerseals.com

B Ref. A G
L R External Pressure B Dash A Min. # Gland ID Gland OD R = 0.015" max. radius L = 0.121/0.123" G = 0.188" minimum +.001/ -.005 -208 0.625 1.000 -209 0.687 1.062 -210 0.750 1.125 -211 0.812 1.187 -212 0.875 1.250 -213 0.937 1.312 -214 1.000 1.375 -215 1.062 1.437 -216 1.125 1.500 -217 1.187 1.562 -218 1.250 1.625 -219 1.312 1.687 -220 1.375 1.750 -221 1.437 1.812 -222 1.500 1.875 -223 1.625 2.000 -224 1.750 2.125 -225 1.875 2.250 -226 2.000 2.375 -227 2.125 2.500 -228 2.250 2.625 -229 2.375 2.750 -230 2.500 2.875 -231 2.625 3.000 -232 2.750 3.125 -233 2.875 3.250 -234 3.000 3.375 -235 3.125 3.500 -236 3.250 3.625 -237 3.375 3.750 -238 3.500 3.875 -239 3.625 4.000 -240 3.750 4.125 -241 3.875 4.250 -242 4.000 4.375 -243 4.125 4.500 Part Number Dash # -244 -245 -246 -247 -248 -249 -250 -251 -252 -253 -254 -255 -256 -257 -258 -259 -260 -261 -262 -263 -264 -265 -266 -267 -268 -269 -270 -271 -272 -273 -274 -275 -276 -277 -278 -279 -280 -281 A Gland ID 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.250 8.500 8.750 9.000 9.250 9.500 9.750 10.000 10.500 11.000 11.500 12.000 13.000 14.000 15.000 B Min. Gland OD 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.125 6.250 6.375 6.625 6.875 7.125 7.375 7.625 7.875 8.125 8.375 8.625 8.875 9.125 9.375 9.625 9.875 10.125 10.375 10.875 11.375 11.875 12.375 13.375 14.375 15.375 Part Number xxxxFEx12504250170xxx xxxxFEx12504375170xxx xxxxFEx12504500170xxx xxxxFEx12504625170xxx xxxxFEx12504750170xxx xxxxFEx12504875170xxx xxxxFEx12505000170xxx xxxxFEx12505125170xxx xxxxFEx12505250170xxx xxxxFEx12505375170xxx xxxxFEx12505500170xxx xxxxFEx12505625170xxx xxxxFEx12505750170xxx xxxxFEx12505875170xxx xxxxFEx12506000170xxx xxxxFEx12506250170xxx xxxxFEx12506500170xxx xxxxFEx12506750170xxx xxxxFEx12507000170xxx xxxxFEx12507250170xxx xxxxFEx12507500170xxx xxxxFEx12507750170xxx xxxxFEx12508000170xxx xxxxFEx12508250170xxx xxxxFEx12508500170xxx xxxxFEx12508750170xxx xxxxFEx12509000170xxx xxxxFEx12509250170xxx xxxxFEx12509500170xxx xxxxFEx12509750170xxx xxxxFEx12510000170xxx xxxxFEx12510500170xxx xxxxFEx12511000170xxx xxxxFEx12511500170xxx xxxxFEx12512000170xxx xxxxFEx12513000170xxx xxxxFEx12514000170xxx xxxxFEx12515000170xxx
xxxxFEx12500625170xxx xxxxFEx12500687170xxx xxxxFEx12500750170xxx xxxxFEx12500812170xxx xxxxFEx12500875170xxx xxxxFEx12500937170xxx xxxxFEx12501000170xxx xxxxFEx12501062170xxx xxxxFEx12501125170xxx xxxxFEx12501187170xxx xxxxFEx12501250170xxx xxxxFEx12501312170xxx xxxxFEx12501375170xxx xxxxFEx12501437170xxx xxxxFEx12501500170xxx xxxxFEx12501625170xxx xxxxFEx12501750170xxx xxxxFEx12501875170xxx xxxxFEx12502000170xxx xxxxFEx12502125170xxx xxxxFEx12502250170xxx xxxxFEx12502375170xxx xxxxFEx12502500170xxx xxxxFEx12502625170xxx xxxxFEx12502750170xxx xxxxFEx12502875170xxx xxxxFEx12503000170xxx xxxxFEx12503125170xxx xxxxFEx12503250170xxx xxxxFEx12503375170xxx xxxxFEx12503500170xxx xxxxFEx12503625170xxx xxxxFEx12503750170xxx xxxxFEx12503875170xxx xxxxFEx12504000170xxx xxxxFEx12504125170xxx
01/15/07
6-11
www.parkerseals.com

B Ref. A G
L R External Pressure B Dash A Min. # Gland ID Gland OD R = 0.015" max. radius L = 0.186/0.188" G = 0.281" minimum +.001/ -.005 -325 1.500 2.062 -326 1.625 2.187 -327 1.750 2.312 -328 1.875 2.437 -329 2.000 2.562 -330 2.125 2.687 -331 2.250 2.812 -332 2.375 2.937 -333 2.500 3.062 -334 2.625 3.187 -335 2.750 3.312 -336 2.875 3.437 -337 3.000 3.562 -338 3.125 3.687 -339 3.250 3.812 -340 3.375 3.937 -341 3.500 4.062 -342 3.625 4.187 -343 3.750 4.312 -344 3.875 4.437 -345 4.000 4.562 -346 4.125 4.687 -347 4.250 4.812 -348 4.375 4.937 -349 4.500 5.062 -350 4.625 5.187 -351 4.750 5.312 -352 4.875 5.437 -353 5.000 5.562 -354 5.125 5.687 -355 5.250 5.812 -356 5.375 5.937 Part Number Dash # -357 -358 -359 -360 -361 -362 -363 -364 -365 -366 -367 -368 -369 -370 -371 -372 -373 -374 -375 -376 -377 -378 -379 -380 -381 -382 -383 -384 -385 -386 -387 -388 -389 -390 A Gland ID 5.500 5.625 5.750 5.875 6.000 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.250 8.500 8.750 9.000 9.250 9.500 9.750 10.000 10.500 11.000 11.500 12.000 13.000 14.000 15.000 16.000 17.000 18.000 19.000 20.000 21.000 B Min. Gland OD 6.062 6.187 6.312 6.437 6.562 6.812 7.062 7.312 7.562 7.812 8.062 8.312 8.562 8.812 9.062 9.312 9.562 9.812 10.062 10.312 10.562 11.062 11.562 12.062 12.562 13.562 14.562 15.562 16.562 17.562 18.562 19.562 20.562 21.562 Part Number xxxxFEx18705500260xxx xxxxFEx18705625260xxx xxxxFEx18705750260xxx xxxxFEx18705875260xxx xxxxFEx18706000260xxx xxxxFEx18706250260xxx xxxxFEx18706500260xxx xxxxFEx18706750260xxx xxxxFEx18707000260xxx xxxxFEx18707250260xxx xxxxFEx18707500260xxx xxxxFEx18707750260xxx xxxxFEx18708000260xxx xxxxFEx18708250260xxx xxxxFEx18708500260xxx xxxxFEx18708750260xxx xxxxFEx18709000260xxx xxxxFEx18709250260xxx xxxxFEx18709500260xxx xxxxFEx18709750260xxx xxxxFEx18710000260xxx xxxxFEx18710500260xxx xxxxFEx18711000260xxx xxxxFEx18711500260xxx xxxxFEx18712000260xxx xxxxFEx18713000260xxx xxxxFEx18714000260xxx xxxxFEx18715000260xxx xxxxFEx18716000260xxx xxxxFEx18717000260xxx xxxxFEx18718000260xxx xxxxFEx18719000260xxx xxxxFEx18720000260xxx xxxxFEx18721000260xxx
xxxxFEx18701500260xxx xxxxFEx18701625260xxx xxxxFEx18701750260xxx xxxxFEx18701875260xxx xxxxFEx18702000260xxx xxxxFEx18702125260xxx xxxxFEx18702250260xxx xxxxFEx18702375260xxx xxxxFEx18702500260xxx xxxxFEx18702625260xxx xxxxFEx18702750260xxx xxxxFEx18702875260xxx xxxxFEx18703000260xxx xxxxFEx18703125260xxx xxxxFEx18703250260xxx xxxxFEx18703375260xxx xxxxFEx18703500260xxx xxxxFEx18703625260xxx xxxxFEx18703750260xxx xxxxFEx18703875260xxx xxxxFEx18704000260xxx xxxxFEx18704125260xxx xxxxFEx18704250260xxx xxxxFEx18704375260xxx xxxxFEx18704500260xxx xxxxFEx18704625260xxx xxxxFEx18704750260xxx xxxxFEx18704875260xxx xxxxFEx18705000260xxx xxxxFEx18705125260xxx xxxxFEx18705250260xxx xxxxFEx18705375260xxx
01/15/06
6-12
www.parkerseals.com

B Ref. A G
L R External Pressure B Dash A Min. # Gland ID Gland OD R = 0.015" max. radius L = 0.238/0.241" G = 0.375" minimum +.001/ -.005 -425 4.500 5.250 -426 4.625 5.375 -427 4.750 5.500 -428 4.875 5.625 -429 5.000 5.750 -430 5.125 5.875 -431 5.250 6.000 -432 5.375 6.125 -433 5.500 6.250 -434 5.625 6.375 -435 5.750 6.500 -436 5.875 6.625 -437 6.000 6.750 -438 6.250 7.000 -439 6.500 7.250 -440 6.750 7.500 -441 7.000 7.750 -442 7.250 8.000 -443 7.500 8.250 -444 7.750 8.500 Part Number Dash # -445 -446 -447 -448 -449 -450 -451 -452 -453 -454 -455 -456 -457 -458 -459 -460 -461 -462 -463 -464 -465 -466 -467 -468 A Gland ID 8.000 8.500 9.000 9.500 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 14.000 14.500 15.000 15.500 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 B Min. Gland OD 8.750 9.250 9.750 10.250 10.750 11.250 11.750 12.250 12.750 13.250 13.750 14.250 14.750 15.250 15.750 16.250 16.750 17.250 17.750 18.250 18.750 19.250 19.750 20.250 Part Number xxxxFEx25008000355xxx xxxxFEx25008500355xxx xxxxFEx25009000355xxx xxxxFEx25009500355xxx xxxxFEx25010000355xxx xxxxFEx25010500355xxx xxxxFEx25011000355xxx xxxxFEx25011500355xxx xxxxFEx25012000355xxx xxxxFEx25012500355xxx xxxxFEx25013000355xxx xxxxFEx25013500355xxx xxxxFEx25014000355xxx xxxxFEx25014500355xxx xxxxFEx25015000355xxx xxxxFEx25015500355xxx xxxxFEx25016000355xxx xxxxFEx25016500355xxx xxxxFEx25017000355xxx xxxxFEx25017500355xxx xxxxFEx25018000355xxx xxxxFEx25018500355xxx xxxxFEx25019000355xxx xxxxFEx25019500355xxx
xxxxFEx25004500355xxx xxxxFEx25004625355xxx xxxxFEx25004750355xxx xxxxFEx25004875355xxx xxxxFEx25005000355xxx xxxxFEx25005125355xxx xxxxFEx25005250355xxx xxxxFEx25005375355xxx xxxxFEx25005500355xxx xxxxFEx25005625355xxx xxxxFEx25005750355xxx xxxxFEx25005875355xxx xxxxFEx25006000355xxx xxxxFEx25006250355xxx xxxxFEx25006500355xxx xxxxFEx25006750355xxx xxxxFEx25007000355xxx xxxxFEx25007250355xxx xxxxFEx25007500355xxx xxxxFEx25007750355xxx
01/15/06
6-13
www.parkerseals.com
FlexiSeal Face Seals FI Profiles Internal Pressure

FI Profiles
FI FlexiSeal Internal Pressure Face Seals are designed so that the spring cavity faces in.
Internal Pressure Face Seal
Part Number Example

Table 6-5. FI Internal Pressure Part Number
6
Internal Pressure
0 3 0 1
FI N
1 2 5
0 1 2 5 0
1 7 0
Internal Face Seal Default Lip Style
Helical Spring
01/15/07
6-14
www.parkerseals.com
FlexiSeal Face Seals Gland Dimensions FI Profiles

Table 6-6. FI Internal Pressure Gland Dimensions
FI Profiles Internal Pressure
B A Ref. G
L R Internal Pressure
Each of these FlexiSeal profiles were designed to fit into either the Inch/Fractional internal pressure face seal glands on the following pages or the Metric glands on Page 6-20.
FIN-H
FIC-V
FID-V
FIK-V
FIN-C
A B Max. Gland ID Gland OD R = 0.015" max. radius L = 0.056/0.058" G = 0.094" minimum +.005/ -.000 -012 0.312 0.500 -013 0.375 0.562 -014 0.437 0.625 -015 0.500 0.687 -016 0.562 0.750 -017 0.625 0.812 -018 0.687 0.875 -019 0.750 0.937 -020 0.812 1.000 -021 0.875 1.062 -022 0.937 1.125 -023 1.000 1.187 -024 1.062 1.250 -025 1.125 1.312 -026 1.187 1.375 -027 1.250 1.437 -028 1.312 1.500 -029 1.437 1.625 -030 1.562 1.750 -031 1.687 1.875 -032 1.812 2.000 -033 1.937 2.125 -034 2.062 2.250 -035 2.187 2.375 -036 2.312 2.500 -037 2.437 2.625 -038 2.562 2.750 -039 2.687 2.875 -040 2.812 3.000 -041 2.937 3.125 Dash #
Part Number
xxxxFIx06200312083xxx xxxxFIx06200375083xxx xxxxFIx06200437083xxx xxxxFIx06200500083xxx xxxxFIx06200562083xxx xxxxFIx06200625083xxx xxxxFIx06200687083xxx xxxxFIx06200750083xxx xxxxFIx06200812083xxx xxxxFIx06200875083xxx xxxxFIx06200937083xxx xxxxFIx06201000083xxx xxxxFIx06201062083xxx xxxxFIx06201125083xxx xxxxFIx06201187083xxx xxxxFIx06201250083xxx xxxxFIx06201312083xxx xxxxFIx06201437083xxx xxxxFIx06201562083xxx xxxxFIx06201687083xxx xxxxFIx06201812083xxx xxxxFIx06201937083xxx xxxxFIx06202062083xxx xxxxFIx06202187083xxx xxxxFIx06202312083xxx xxxxFIx06202437083xxx xxxxFIx06202562083xxx xxxxFIx06202687083xxx xxxxFIx06202812083xxx xxxxFIx06202937083xxx
01/15/06
6-15
www.parkerseals.com

Table 6-6. FI Internal Pressure Gland Dimensions (Continued)
B A Ref. G
L R Internal Pressure A B Max. Gland ID Gland OD R = 0.015" max. radius L = 0.056/0.058" G = 0.094" minimum +.005/ -.000 -042 3.187 3.375 -043 3.437 3.625 -044 3.687 3.875 -045 3.937 4.125 R = 0.015" max. radius L = 0.089/0.091" G = 0.141" minimum +.005/ -.000 -112 0.405 0.687 -113 0.468 0.750 -114 0.530 0.812 -115 0.593 0.875 -116 0.655 0.937 -117 0.718 1.000 -118 0.780 1.062 -119 0.843 1.125 -120 0.905 1.187 -121 0.968 1.250 -122 1.030 1.312 -123 1.093 1.375 -124 1.155 1.437 -125 1.218 1.500 -126 1.280 1.562 -127 1.343 1.625 -128 1.405 1.687 -129 1.468 1.750 -130 1.530 1.812 -131 1.593 1.875 -132 1.655 1.937 -133 1.718 2.000 -134 1.780 2.062 -135 1.843 2.125 Dash # Part Number Dash # -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -151 -152 -153 -154 -155 -156 -157 -158 -159 -160 -161 -162 -163 -164 -165 -166 -167 A Max. Gland ID 1.905 1.968 2.030 2.093 2.155 2.218 2.280 2.343 2.405 2.468 2.530 2.593 2.655 2.718 2.780 2.905 3.155 3.405 3.655 3.905 4.155 4.405 4.655 4.905 5.155 5.405 5.655 5.905 6.155 6.405 6.655 6.905 B Gland OD 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 2.937 3.000 3.062 3.187 3.437 3.687 3.937 4.187 4.437 4.687 4.937 5.187 5.437 5.687 5.937 6.187 6.437 6.687 6.937 7.187 Part Number xxxxFIx09301905130xxx xxxxFIx09301968130xxx xxxxFIx09302030130xxx xxxxFIx09302093130xxx xxxxFIx09302155130xxx xxxxFIx09302218130xxx xxxxFIx09302280130xxx xxxxFIx09302343130xxx xxxxFIx09302405130xxx xxxxFIx09302468130xxx xxxxFIx09302530130xxx xxxxFIx09302593130xxx xxxxFIx09302655130xxx xxxxFIx09302718130xxx xxxxFIx09302780130xxx xxxxFIx09302905130xxx xxxxFIx09303155130xxx xxxxFIx09303405130xxx xxxxFIx09303655130xxx xxxxFIx09303905130xxx xxxxFIx09304155130xxx xxxxFIx09304405130xxx xxxxFIx09304655130xxx xxxxFIx09304905130xxx xxxxFIx09305155130xxx xxxxFIx09305405130xxx xxxxFIx09305655130xxx xxxxFIx09305905130xxx xxxxFIx09306155130xxx xxxxFIx09306405130xxx xxxxFIx09306655130xxx xxxxFIx09306905130xxx
xxxxFIx06203187083xxx xxxxFIx06203437083xxx xxxxFIx06203687083xxx xxxxFIx06203937083xxx
xxxxFIx09300405130xxx xxxxFIx09300468130xxx xxxxFIx09300530130xxx xxxxFIx09300593130xxx xxxxFIx09300655130xxx xxxxFIx09300718130xxx xxxxFIx09300780130xxx xxxxFIx09300843130xxx xxxxFIx09300905130xxx xxxxFIx09300968130xxx xxxxFIx09301030130xxx xxxxFIx09301093130xxx xxxxFIx09301155130xxx xxxxFIx09301218130xxx xxxxFIx09301280130xxx xxxxFIx09301343130xxx xxxxFIx09301405130xxx xxxxFIx09301468130xxx xxxxFIx09301530130xxx xxxxFIx09301593130xxx xxxxFIx09301655130xxx xxxxFIx09301718130xxx xxxxFIx09301780130xxx xxxxFIx09301843130xxx
01/15/06
6-16
www.parkerseals.com

B A Ref. G
L R Internal Pressure A B Max. Gland OD Gland ID R = 0.015" max. radius L = 0.121/0.123" G = 0.188" minimum +.005/ -.000 -210 0.625 1.000 -211 0.687 1.062 -212 0.750 1.125 -213 0.812 1.187 -214 0.875 1.250 -215 0.937 1.312 -216 1.000 1.375 -217 1.062 1.437 -218 1.125 1.500 -219 1.187 1.562 -220 1.250 1.625 -221 1.312 1.687 -222 1.375 1.750 -223 1.500 1.875 -224 1.625 2.000 -225 1.750 2.125 -226 1.875 2.250 -227 2.000 2.375 -228 2.125 2.500 -229 2.250 2.625 -230 2.375 2.750 -231 2.500 2.875 -232 2.625 3.000 -233 2.750 3.125 -234 2.875 3.250 -235 3.000 3.375 -236 3.125 3.500 -237 3.250 3.625 -238 3.375 3.750 -239 3.500 3.875 -240 3.625 4.000 -241 3.750 4.125 -242 3.875 4.250 -243 4.000 4.375 Dash # Part Number Dash # -244 -245 -246 -247 -248 -249 -250 -251 -252 -253 -254 -255 -256 -257 -258 -259 -260 -261 -262 -263 -264 -265 -266 -267 -268 -269 -270 -271 -272 -273 -274 -275 -276 -277 -278 -279 -280 -281 A Max. Gland ID 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.125 6.375 6.625 6.875 7.125 7.375 7.625 7.875 8.125 8.375 8.625 8.875 9.125 9.375 9.625 9.875 10.375 10.875 11.375 11.875 12.375 12.875 13.375 B Gland OD 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.125 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.250 8.500 8.750 9.000 9.250 9.500 9.750 10.000 10.250 10.750 11.250 11.750 12.250 12.750 13.250 13.750 Part Number xxxxFIx12504125170xxx xxxxFIx12504250170xxx xxxxFIx12504375170xxx xxxxFIx12504500170xxx xxxxFIx12504625170xxx xxxxFIx12504750170xxx xxxxFIx12504875170xxx xxxxFIx12505000170xxx xxxxFIx12505125170xxx xxxxFIx12505250170xxx xxxxFIx12505375170xxx xxxxFIx12505500170xxx xxxxFIx12505625170xxx xxxxFIx12505750170xxx xxxxFIx12505875170xxx xxxxFIx12506125170xxx xxxxFIx12506375170xxx xxxxFIx12506625170xxx xxxxFIx12506875170xxx xxxxFIx12507125170xxx xxxxFIx12507375170xxx xxxxFIx12507625170xxx xxxxFIx12507875170xxx xxxxFIx12508125170xxx xxxxFIx12508375170xxx xxxxFIx12508625170xxx xxxxFIx12508875170xxx xxxxFIx12509125170xxx xxxxFIx12509375170xxx xxxxFIx12509625170xxx xxxxFIx12509875170xxx xxxxFIx12510375170xxx xxxxFIx12510875170xxx xxxxFIx12511375170xxx xxxxFIx12511875170xxx xxxxFIx12512375170xxx xxxxFIx12512875170xxx xxxxFIx12513375170xxx
xxxxFIx12500625170xxx xxxxFIx12500687170xxx xxxxFIx12500750170xxx xxxxFIx12500812170xxx xxxxFIx12500875170xxx xxxxFIx12500937170xxx xxxxFIx12501000170xxx xxxxFIx12501062170xxx xxxxFIx12501125170xxx xxxxFIx12501187170xxx xxxxFIx12501250170xxx xxxxFIx12501312170xxx xxxxFIx12501375170xxx xxxxFIx12501500170xxx xxxxFIx12501625170xxx xxxxFIx12501750170xxx xxxxFIx12501875170xxx xxxxFIx12502000170xxx xxxxFIx12502125170xxx xxxxFIx12502250170xxx xxxxFIx12502375170xxx xxxxFIx12502500170xxx xxxxFIx12502625170xxx xxxxFIx12502750170xxx xxxxFIx12502875170xxx xxxxFIx12503000170xxx xxxxFIx12503125170xxx xxxxFIx12503250170xxx xxxxFIx12503375170xxx xxxxFIx12503500170xxx xxxxFIx12503625170xxx xxxxFIx12503750170xxx xxxxFIx12503875170xxx xxxxFIx12504000170xxx
01/15/07
6-17
www.parkerseals.com

B A Ref. G
L R Internal Pressure A B Max. Gland ID Gland OD R = 0.015" max. radius L = 0.186/0.188" G = 0.281" minimum +.005/ -.000 -325 1.312 1.875 -326 1.437 2.000 -327 1.562 2.125 -328 1.687 2.250 -329 1.812 2.375 -330 1.937 2.500 -331 2.062 2.625 -332 2.187 2.750 -333 2.312 2.875 -334 2.437 3.000 -335 2.562 3.125 -336 2.687 3.250 -337 2.812 3.375 -338 2.937 3.500 -339 3.062 3.625 -340 3.187 3.750 -341 3.312 3.875 -342 3.437 4.000 -343 3.562 4.125 -344 3.687 4.250 -345 3.812 4.375 -346 3.937 4.500 -347 4.062 4.625 -348 4.187 4.750 -349 4.312 4.875 -350 4.437 5.000 -351 4.562 5.125 -352 4.687 5.250 -353 4.812 5.375 -354 4.937 5.500 -355 5.062 5.625 -356 5.187 5.750 Dash # Part Number Dash # -357 -358 -359 -360 -361 -362 -363 -364 -365 -366 -367 -368 -369 -370 -371 -372 -373 -374 -375 -376 -377 -378 -379 -380 -381 -382 -383 -384 -385 -386 -387 -388 -389 -390 A Max. Gland ID 5.312 5.437 5.562 5.687 5.812 6.062 6.312 6.562 6.812 7.062 7.312 7.562 7.812 8.062 8.312 8.562 8.812 9.062 9.312 9.562 9.812 10.312 10.812 11.312 11.812 12.812 13.812 14.812 15.812 16.812 17.812 18.812 19.812 20.812 B Gland OD 5.875 6.000 6.125 6.250 6.375 6.625 6.875 7.125 7.375 7.625 7.875 8.125 8.375 8.625 8.875 9.125 9.375 9.625 9.875 10.125 10.375 10.875 11.375 11.875 12.375 13.375 14.375 15.375 16.375 17.375 18.375 19.375 20.375 21.375 Part Number xxxxFIx18705312260xxx xxxxFIx18705437260xxx xxxxFIx18705562260xxx xxxxFIx18705687260xxx xxxxFIx18705812260xxx xxxxFIx18706062260xxx xxxxFIx18706312260xxx xxxxFIx18706562260xxx xxxxFIx18706812260xxx xxxxFIx18707062260xxx xxxxFIx18707312260xxx xxxxFIx18707562260xxx xxxxFIx18707812260xxx xxxxFIx18708062260xxx xxxxFIx18708312260xxx xxxxFIx18708562260xxx xxxxFIx18708812260xxx xxxxFIx18709062260xxx xxxxFIx18709312260xxx xxxxFIx18709562260xxx xxxxFIx18709812260xxx xxxxFIx18710312260xxx xxxxFIx18710812260xxx xxxxFIx18711312260xxx xxxxFIx18711812260xxx xxxxFIx18712812260xxx xxxxFIx18713812260xxx xxxxFIx18714812260xxx xxxxFIx18715812260xxx xxxxFIx18716812260xxx xxxxFIx18717812260xxx xxxxFIx18718812260xxx xxxxFIx18719812260xxx xxxxFIx18720812260xxx
xxxxFIx18701312260xxx xxxxFIx18701437260xxx xxxxFIx18701562260xxx xxxxFIx18701687260xxx xxxxFIx18701812260xxx xxxxFIx18701937260xxx xxxxFIx18702062260xxx xxxxFIx18702187260xxx xxxxFIx18702312260xxx xxxxFIx18702437260xxx xxxxFIx18702562260xxx xxxxFIx18702687260xxx xxxxFIx18702812260xxx xxxxFIx18702937260xxx xxxxFIx18703062260xxx xxxxFIx18703187260xxx xxxxFIx18703312260xxx xxxxFIx18703437260xxx xxxxFIx18703562260xxx xxxxFIx18703687260xxx xxxxFIx18703812260xxx xxxxFIx18703937260xxx xxxxFIx18704062260xxx xxxxFIx18704187260xxx xxxxFIx18704312260xxx xxxxFIx18704437260xxx xxxxFIx18704562260xxx xxxxFIx18704687260xxx xxxxFIx18704812260xxx xxxxFIx18704937260xxx xxxxFIx18705062260xxx xxxxFIx18705187260xxx
01/15/06
6-18
www.parkerseals.com

B A Ref. G
L R Internal Pressure A B Max. Gland ID Gland OD R = 0.015" max. radius L = 0.238/0.241" G = 0.375" minimum +.005/ -.000 -425 4.250 5.000 -426 4.375 5.125 -427 4.500 5.250 -428 4.625 5.375 -429 4.750 5.500 -430 4.875 5.625 -431 5.000 5.750 -432 5.125 5.875 -433 5.250 6.000 -434 5.375 6.125 -435 5.500 6.250 -436 5.625 6.375 -437 5.750 6.500 -438 6.000 6.750 -439 6.250 7.000 -440 6.500 7.250 -441 6.750 7.500 -442 7.000 7.750 -443 7.250 8.000 -444 7.500 8.250 Dash # Part Number Dash # -445 -446 -447 -448 -449 -450 -451 -452 -453 -454 -455 -456 -457 -458 -459 -460 -461 -462 -463 -464 -465 -466 -467 -468 A Max. Gland ID 7.750 8.250 8.750 9.250 9.750 10.250 10.750 11.250 11.750 12.250 12.750 13.250 13.750 14.250 14.750 15.250 15.750 16.250 16.750 17.250 17.750 18.250 18.750 19.250 B Gland OD 8.500 9.000 9.500 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 14.000 14.500 15.000 15.500 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 20.000 Part Number xxxxFIx25007750355xxx xxxxFIx25008250355xxx xxxxFIx25008750355xxx xxxxFIx25009250355xxx xxxxFIx25009750355xxx xxxxFIx25010250355xxx xxxxFIx25010750355xxx xxxxFIx25011250355xxx xxxxFIx25011750355xxx xxxxFIx25012250355xxx xxxxFIx25012750355xxx xxxxFIx25013250355xxx xxxxFIx25013750355xxx xxxxFIx25014250355xxx xxxxFIx25014750355xxx xxxxFIx25015250355xxx xxxxFIx25015750355xxx xxxxFIx25016250355xxx xxxxFIx25016750355xxx xxxxFIx25017250355xxx xxxxFIx25017750355xxx xxxxFIx25018250355xxx xxxxFIx25018750355xxx xxxxFIx25019250355xxx
xxxxFIx25004250355xxx xxxxFIx25004375355xxx xxxxFIx25004500355xxx xxxxFIx25004625355xxx xxxxFIx25004750355xxx xxxxFIx25004875355xxx xxxxFIx25005000355xxx xxxxFIx25005125355xxx xxxxFIx25005250355xxx xxxxFIx25005375355xxx xxxxFIx25005500355xxx xxxxFIx25005625355xxx xxxxFIx25005750355xxx xxxxFIx25006000355xxx xxxxFIx25006250355xxx xxxxFIx25006500355xxx xxxxFIx25006750355xxx xxxxFIx25007000355xxx xxxxFIx25007250355xxx xxxxFIx25007500355xxx
01/15/07
6-19
www.parkerseals.com
FlexiSeal Face Seals FE & FI Profiles Metric

FE & FI Metric Profiles
FE FlexiSeal External Pressure Face Seals are designed so that the spring cavity faces out. FI FlexiSeal Internal Pressure Face Seals are designed so that the spring cavity faces in. FE & FI profiles are available in the Metric sizes on Page 6-21.
Part Number Example
Table 6-7. Metric Face Seal Part Number

M 5 0 2
FE N
0 2 5 0
0 2 9 5 0
0 3 3
External Pressure
Material Code
Cross-Section
External Face Seal No Lip Style
Gland ID
Helical Spring
Internal Pressure
01/15/06
6-20
www.parkerseals.com
FlexiSeal Face Seals Gland Dimensions FE & FI Profiles

Table 6-8. FE & FI Metric Gland Dimensions
B (Ref) A (h9)* G
FE & FI Profiles Metric
B (H9)* A (Ref.)
L R0.38 External Pressure R0.38 Internal Pressure CrossSection Callout 0200 0250 0400 0500 0700 Gland CrossSection 2.00/2.05 mm 2.50/2.55 mm 4.00/4.05 mm 5.00/5.05 mm 7.00/7.08 mm Heel Height Callout 021 033 043 066 090 Min. Groove Width (G) 2.39 mm 3.58 mm 4.78 mm 7.14 mm 9.53 mm
Each of these FlexiSeal profiles were designed to fit into the metric glands on this page.
** For ISO Tolerances see Appendix D. FEN-H FEC-V

Part Number Groove ID (A) in mm Groove OD (B) in mm Groove Groove Depth Width (G) in (L) in mm mm
FED-V
FEK-V
FED-V Profile M601FED025002450033EVM 24.50 +.00/-.05 31.66 min. 2.50/2.55 3.58 min. FIN-C Profile M301FIN050025500066HCH 255.00 max. 269.28 +.13/-.00 5.00/5.05 7.14 min.
FEN-C
FIN-H
FIC-V
FID-V
FIK-V
FIN-C
01/15/06
6-21
www.parkerseals.com
Notes
6-22
www.parkerseals.com
FlexiSeal Rotary Seals Introduction

Contents
Engineering . . . . . . . . . . . . . . . . . Materials . . . . . . . . . . . . . . . . . . . Product Offering . . . . . . . . . . . . . FlexiSeal Rotary FC and FH Profiles Inch/Fractional . . . . . . . . . . . . 7-9 7-2 7-4 7-5
Rotary FlexiSeal is the answer for many radial applications.
FC and FH Profiles Metric . . . . . . . . . . . . . . . . . . . 7-16 FF Profiles Flanged Inch/Fractional . . . . . 7-18 FF Profiles Flanged Metric . . . . . . . . . . . . 7-26
The Rotary FlexiSeal should be used when speeds are relatively low (<1000 sfpm) and pressures are high (up to 10,000 psi). FlexiLip and FlexiCase profiles should be used when pressures are low and speeds high. Rotary FlexiSeals feature either a flanged design or an O-ring on the OD to keep the seal fixed in the bore as the shaft rotates. The O-ring can either be centered along the OD or be located in the heel of the seal. Virtually any O-ring material can be supplied with a custom rotary FlexiSeal, but a fluorocarbon material is standard.
Applications
Radial applications with extreme conditions that involve lower speeds and higher pressures, for which the Rotary FlexiSeal is best suited, include:
Compressors Cryogenics FDA Clean Grade Jet Engines Hydraulic Cylinders Pressure Washers Robotics Rotary Unions Steering Cylinders Swivels Vapor Recovery Systems Many more
Rotary FlexiSeal
Markets
Since the FlexiSeal solves problems along several parameters, it can be found in virtually every market including:
Rotary Application Aerospace Automotive Chemical Process Appliances Electronic Food & Beverage Heavy Machinery Hydraulic Machine Tools Marine Medical Military Oil & Gas Pharmaceutical Semiconductor
Chamfered ID, O-Ring OD Rotary FlexiSeal
01/15/06
7-1
www.parkerseals.com
FlexiSeal Rotary Seals Engineering

While choosing the right Rotary FlexiSeal for your application, you need to consider: Pressure Shaft Velocity Lubrication Shaft Misalignment Shaft Runout Shaft Hardness Shaft Surface Finish Different Spring Choices Lip Shapes Shaft Lead
Media Being Sealed
Shaft Hardness and Surface Finish

It is critical to match the right surface roughness with the media being sealed, especially when the surface is hardened and the original finish will take some time to break in. See Table 7-1 for recommendations and Pages 2-9 and 2-10 for a more general discussion on the topic. Table 7-1. Surface Roughness, Ra
Dynamic Static Surfaces Surfaces inch m inch m 04 max. 0.1 max.0 08 max. 0.2 max.
Pressure and Shaft Velocity

Unlike reciprocating applications, seals ride on a rotating shaft in only one small area where dynamic forces and energy are concentrated. For a guide to aid in the choice of seal profile and material for optimum seal life, see Page 2-17.
Cryogenics Helium Gas 06 max. 0.15 max. 12 max. 0.3 max. Hydrogen Gas Freon Air Nitrogen Gas Argon 08 max. 0.2 max. 16 max. 0.4 max. Natural Gas Fuel (Aircraft and Automotive) Water Hydraulic Oil 12 max. 0.3 max. 32 max. 0.8 max. Crude Oil Sealants
Lubrication
While FlexiSeals made of PTFE have a natural lubricity and can be used in unlubricated applications, a film of lubricant between the seal lip and the shaft reduces seal wear and frictional heat generation, makes higher surface speeds possible, and helps prevent the seal from wearing a groove in the shaft.
Spring Choices
Rotary FlexiSeals are available with two different spring designs to energize the jacket: V-shaped cantilever springs (V Series) and cantedcoil springs (C Series). The FFN-H flanged design included in this section uses the helical spring (H Series) and should only be used for static or very slow rotary. Details on spring features can be found on Page 2-12.
Shaft Misalignment and Runout

Applications with rotating shafts may develop problems associated with shaft misalignment. Because rotary FlexiSeals are spring-loaded, they normally handle runout and eccentricity better than FlexiLip and FlexiCase seals. For more information about problems with eccentricity and runout, see Page 2-19.
01/15/06
7-2
www.parkerseals.com
FlexiSeal Rotary Seals

Table 7-2. Recommended Applications for FlexiSeal Rotary Springs
V Series rotary shafts <1000 sfpm wide tolerance and misaligned glands abrasive media (when scraper lip is designated) dynamic applications to 450 F C Series rotary shafts <1000 sfpm wide tolerance and misaligned glands friction critical and very small diameter applications dynamic applications to 450 F
Engineering
H Series flanged rotary seals static or very slow dynamic seals (<50 sfpm) when sealability is critical applications below -100 F
Lip Shapes
Rotary FlexiSeal profiles can be optimized by changing their lip shapes. Chamfered lips maximize sealability while minimizing friction. Scraper lips prevent particles from accumulating at the lip, which makes wash-downs more effective.
Shaft Machine Lead

To avoid pumping fluid under the seal lip, the lead from machining needs to be kept to less than 0.05 degrees. More on machine lead on Page 2-20.
01/15/06
7-3
www.parkerseals.com
FlexiSeal Rotary Seals Materials

The most popular PTFE fillers used for FlexiSeal Rotary products are carbon fiber, graphite, Ryton*/carbon and Ryton/carbon/TFM. PTFE is also popular for these products without any filler (virgin PTFE). 0502 Carbon Fiber Filled
Carbon fiber lowers creep, increases flex and compressive modulus and raises hardness. Coefficient of thermal expansion is lowered and thermal conductivity is higher for compounds of carbon fiber filled PTFE. Ideal for automotive applications in shock absorbers and water pumps. 0602 Ryton/Carbon Filled Ryton/Carbon filled PTFE features improved surface lubricity and abrasion resistance. It should be used only on shafts hardened to 60 Rc or more. 0301 Graphite Filled Graphite filled PTFE has extremely low coefficient of friction due to the low friction characteristics of graphite. Graphite is chemically inert. Graphite imparts excellent wear properties and high PV to PTFE. 0601 Aromatic Polyester Filled Aromatic Polyester offers excellent high temperature capabilities and excellent wear resistance against soft, dynamic surfaces. Aromatic polyester is not recommended for sealing applications involving steam. 0203 Fiberglass Filled Glass fiber is the most common filler with a positive impact on creep performance of PTFE. Glass fiber adds wear resistance and offers good compression strength.
A number of other fillers are used in combination with PTFE, and non-PTFE compounds are available. More information on these materials and their properties is available in Tab 3. For best results consult the EPS Division PTFE Application Engineering team at (801) 972-3000.
* Ryton is a registered trademark of Chevron Phillips Chemical Company.
01/15/06
7-4
www.parkerseals.com
FlexiSeal Rotary Seals Product Offering

Decision Tree
Medium to High Speed Rotary FlexiSeal
The decision trees in this guide are to be used as an engineering guide only. Often several other parameters must be considered to optimize seal design. Contact Parkers PTFE Engineering Team for confirmation of your choice or further recommendations. Parker also recommends that any seal be tested in the application conditions before releasing for production.
Yes
Low Friction/Long Life? Better Sealability?
FFS-C Pages 7-18 and 7-26
FFS-V Pages 7-18 and 7-26
Cross-Section?
187"
FHS-C Pages 7-9 and 7-16

No Yes
Low Friction/ Long Life? Better Sealability? Cross-Section?
FCS-C Pages 7-9 and 7-16 FHS-V Pages 7-9 and 7-16
No Yes
Cavity Accepts Flanged Seal?
No
187"
Surface Speed above 100 sfpm?
Yes No
FCS-V Pages 7-9 and 7-16
Abrasive Sealing Media?
Yes No
FBS-V FBM-V Pages 5-10 and 5-17
Low Friction/Long Life? Better Sealability?

Yes
FFC-C Pages 7-18 and 7-26
FFC-V Pages 7-18 and 7-26 FHC-C Pages 7-9 and 7-16
No Yes
Cavity Accepts Flanged Seal?
No
187" Cross-Section?
Low Friction/ Long Life? Better Sealability?
FCC-C Pages 7-9 and 7-16 FHC-V Pages 7-9 and 7-16
No Yes
187" Cross-Section?
Surface Speed above 100 sfpm?
Yes No
FCC-V Pages 7-9 and 7-16
FBK-V FBC-V Pages 5-10 and 5-17 01/15/07
7-5
www.parkerseals.com
Product Offering Part Number Nomenclature FlexiSeal Rotary

Table 7-3. FlexiSeal Rotary Part Number Nomenclature
English 0 5 0 2 FC S 1 2 5 0 0 5 0 0 1 7 0 S C L
4-Digit Material Code Examples: 0502 = Carbon Fiber 0502 = Filled PTFE 0602 = Ryton/Carbon 0502 = Filled PTFE
Gland Cross-Section Examples: 062 = 0.062" 093 = 0.093" 125 = 0.125" 187 = 0.187" 250 = 0.250" Lip Style Designation N = Default/No Lip Style C = Chamfered ID & OD S = Scraper ID
Seal Height Designation Examples: 083 = 0.083" 130 = 0.130" 170 = 0.170" 260 = 0.260" 355 = 0.355" Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
FlexiSeal Gland Type Classification FC = Rotary Shaft Centered O-Ring FH = Rotary Shaft O-Ring in Heel FF = Rotary Shaft Flanged
Shaft Diameter Examples: 00500 = 0.500" 02500 = 2.500" 11000 = 11.000"
Metric M 5 0 2 FC S 0 7 0 0 1 0 0 0 0 0 9 0 S C L
7
Gland Cross-Section Examples: 0200 = 2.00 mm 0250 = 2.50 mm 0400 = 4.00 mm 0500 = 5.00 mm 0700 = 7.00 mm Lip Style Designation N = Default/No Lip Style C = Chamfered ID & OD S = Scraper ID Seal Height Designation Examples: 021 = 2.1 mm 033 = 3.3 mm 043 = 4.3 mm 066 = 6.6 mm 090 = 9.0 mm Spring Material E = ELGILOY S = Stainless Steel H = HASTELLOY Spring Design V = Cantilever C = Canted-Coil Spring H = Helical Spring Spring Load Blank = No Option (Helical Only) L = Light M = Medium H = Heavy
4-Digit Material Code Examples: M502 = Carbon Fiber M502 = Filled PTFE M602 = Ryton/Carbon M502 = Filled PTFE (M indicates metric)
FlexiSeal Gland Type Classification FC = Rotary Shaft Centered O-Ring FH = Rotary Shaft O-Ring in Heel FF = Rotary Shaft Flanged
Shaft Diameter Examples: 00800 = 88.00 mm 01150 = 11.50 mm 06500 = 65.00 mm
FCC-C FCC-V
FCS-V
FCS-C
FHC-V
FHS-V
FHC-C
FHS-C
FFC-V
FFS-V
FFC-C
FFS-C FFN-H 01/15/07
7-6
www.parkerseals.com
FlexiSeal Rotary Seals Profiles

Product Offering
Profile
Features
Available as Max. Gland Standard in Low Good in Rotary Available Recommended High Pressure Friction Pressure Abrasive Surface Dimension in Table Applications Extended Heel Rating Speed Sealability Media Location Mil-G-5514 (up to (in sfpm) 10,000 psi) Optimum Yes sealability. Available in 187 cross-section and higher. Medium Very Good No 1000 Pages 7-9, 7-16 No
FCC-V
O-Ring Centered in OD, Chamfered ID, Cantilever Spring
FCS-V
O-Ring Centered in OD, Scraper ID, Cantilever Spring
Minimizes Yes contamination threat. Available in 187 crosssection and higher.
Medium Very Good Yes
1000
Pages 7-9, 7-16
No
FCC-C
O-Ring Centered in OD, Chamfered ID, Canted-Coil Spring
Reduced friction Yes and sealability. Available in 187 cross-section and higher.
Very Low
Good
No
1000
Pages 7-9, 7-16
No
FCS-C
O-Ring Centered in OD, Scraper ID, Canted-Coil Spring
Low friction with Yes contamination resistance. Available in 187 cross-section and higher.
Low
Good
Yes
1000
Pages 7-9, 7-16
No
FHC-V
O-Ring in Heel OD, Chamfered ID, Cantilever Spring
Optimum sealability. Available in extended heel option only.
Yes
Medium Very Good No
1000
Pages 7-9, 7-16
No
FHS-V
O-Ring in Heel OD, Scraper ID, Cantilever Spring
Minimizes Yes contamination threat. Available in extended heel option only.
1000
Pages 7-9, 7-16
No
01/15/07
7-7
www.parkerseals.com
Product Offering
Profile
Features
Available as Max. Gland Standard in Low Good in Rotary Available Recommended High Pressure Friction Pressure Abrasive Surface Dimension in Table Applications Extended Heel Rating Sealability Media Speed Location Mil-G-5514 (up to (in sfpm) 10,000 psi) Reduced friction Yes and sealability. Available in extended heel option only. Low friction with Yes contamination resistance. Available in extended heel option only. Optimum sealability. Premium bore retention. No Very Low Good No 1000 Pages 7-9, 7-16 No
FHC-C
O-Ring in Heel OD, Chamfered ID, Canted-Coil Spring
FHS-C
O-Ring in Heel OD, Scraper ID, Canted-Coil Spring
Low
Good
Yes
1000
Pages 7-9, 7-16
No
FFC-V
Flanged Heel OD, Chamfered ID, Cantilever Spring
Medium Very Good No
1500
Pages 7-18, No 7-26
FFS-V
Flanged Heel OD, Scraper ID, Cantilever Spring
Minimizes No contamination threat. Premium bore retention.
1500
Pages 7-18, No 7-26
FFC-C
Flanged Heel OD, Chamfered ID, Canted-Coil Spring
Reduced friction No and sealability. Premium bore retention.
Very Low
Good
No
1500
Pages 7-18, No 7-26
7
FFS-C Flanged Heel OD, Scraper ID, Canted-Coil Spring Low friction with No contamination resistance. Premium bore retention. Low Good Yes 1500 Pages 7-18, No 7-26
FFN-H
Flanged Heel OD, Rounded ID, Helical Spring
Static or No intermittent rotary only. High sealability and friction.
High
Excellent
No
50
Pages 7-18, No 7-26
01/15/06
7-8
www.parkerseals.com
FlexiSeal Rotary Seals FC and FH Profiles Inch/Fractional

FC and FH Profiles
FC FlexiSeal Rotary Shaft, Centered O-Ring profiles and FH FlexiSeal Rotary Shaft, O-Ring in Heel profiles are available in the Industrial Inch/Fractional and Metric sizes on the following pages.

Hardware Configurations/Installation, see Page 2-3 Surface Finish and Hardness, see Page 2-9 Extrusion Gaps and High Pressure, see Page 2-10 Spring Choices, see Page 2-12 Lip Shapes, see Page 2-16 Rotary Seal Considerations, see Page 2-17 Shaft Misalignment Issues, see Page 2-19
Part Number Example

Table 7-6. FC and FH Inch/Fractional Part Number
0 5 0 2
FC C
1 8 7
0 1 5 0 0
2 6 0
Rotary Shaft Centered O-Ring Chamfered ID & OD Lip
Cantilever Spring

Rotary Application

Radial Cross-Section 093 125 187 250 Std. FC Seal Height Callout N/A N/A 260 355 Std. FH Seal Height Callout 195 265 345 425
0 5 0 2 F C C 1 8 7 0 4 0 0 0
2 6 0
H C M
Seal Height
Note: FH profiles are available in extended heel only.
0 5 0 2
F C C
1 8 7
0 4 0 0 0
3 1 0
H C M
Seal Height
01/15/07
7-9
www.parkerseals.com
FC and FH Profiles Inch/Fractional Gland Dimensions FC and FH Profiles

Table 7-7. FC and FH Inch/Fractional Gland Dimensions
Rotary Seal
FC part numbers are available only in 187 (3/16") cross-section and higher.
FCC-V
FCS-V
FCC-C
FCS-C
FH part numbers are available in extended heel only.
FHC-V
FHS-V
FHC-C
FHS-C
01/15/07
7-10
www.parkerseals.com
FC and FH Profiles Inch/Fractional
Table 7-7. FC and FH Inch/Fractional Gland Dimensions (Continued)

G R
Rotary Seal A B Part Number Shaft Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for FH Seal groove = 0.210/0.220" (195 callout) +.000/ +.002/ -.002 -.000 -106 0.187 0.375 xxxxFHx09300187195xxx -107 0.219 0.406 xxxxFHx09300219195xxx -108 0.250 0.437 xxxxFHx09300250195xxx -109 0.312 0.500 xxxxFHx09300312195xxx -110 0.375 0.562 xxxxFHx09300375195xxx -111 0.437 0.625 xxxxFHx09300437195xxx -112 0.500 0.687 xxxxFHx09300500195xxx -113 0.562 0.750 xxxxFHx09300562195xxx -114 0.625 0.812 xxxxFHx09300625195xxx -115 0.687 0.875 xxxxFHx09300687195xxx -116 0.750 0.937 xxxxFHx09300750195xxx -117 0.812 1.000 xxxxFHx09300812195xxx -118 0.875 1.062 xxxxFHx09300875195xxx -119 0.937 1.125 xxxxFHx09300937195xxx -120 1.000 1.187 xxxxFHx09301000195xxx -121 1.062 1.250 xxxxFHx09301062195xxx Dash # Dash # -122 -123 -124 -125 -126 -127 -128 -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -151 -152 -153 -154 -155 -156 -157 A Shaft Diameter 1.125 1.187 1.250 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.812 1.875 1.937 2.000 2.062 2.125 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 3.000 3.250 3.500 3.750 4.000 4.250 4.500 B Groove Diameter 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.812 1.875 1.937 2.000 2.062 2.125 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 2.937 3.000 3.062 3.187 3.437 3.687 3.937 4.187 4.437 4.687 Part Number xxxxFHx09301125195xxx xxxxFHx09301187195xxx xxxxFHx09301250195xxx xxxxFHx09301312195xxx xxxxFHx09301375195xxx xxxxFHx09301437195xxx xxxxFHx09301500195xxx xxxxFHx09301562195xxx xxxxFHx09301625195xxx xxxxFHx09301687195xxx xxxxFHx09301750195xxx xxxxFHx09301812195xxx xxxxFHx09301875195xxx xxxxFHx09301937195xxx xxxxFHx09302000195xxx xxxxFHx09302062195xxx xxxxFHx09302125195xxx xxxxFHx09302187195xxx xxxxFHx09302250195xxx xxxxFHx09302312195xxx xxxxFHx09302375195xxx xxxxFHx09302437195xxx xxxxFHx09302500195xxx xxxxFHx09302562195xxx xxxxFHx09302625195xxx xxxxFHx09302687195xxx xxxxFHx09302750195xxx xxxxFHx09302812195xxx xxxxFHx09302875195xxx xxxxFHx09303000195xxx xxxxFHx09303250195xxx xxxxFHx09303500195xxx xxxxFHx09303750195xxx xxxxFHx09304000195xxx xxxxFHx09304250195xxx xxxxFHx09304500195xxx 01/15/07
7-11
www.parkerseals.com

G R
Rotary Seal A B Part Number Shaft Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for FH Seal groove = 0.210/0.220" (195 callout) +.000/ +.002/ -.002 -.000 -158 4.750 4.937 xxxxFHx09304750195xxx -159 5.000 5.187 xxxxFHx09305000195xxx -160 5.250 5.437 xxxxFHx09305250195xxx -161 5.500 5.687 xxxxFHx09305500195xxx -162 5.750 5.928 xxxxFHx09305750195xxx -163 6.000 6.187 xxxxFHx09306000195xxx R = 0.015" max. radius E = 0.002" max. G for FH Seal groove = 0.285/0.295" (265 callout) +.000/ +.002/ -.002 -.000 -202 0.250 0.500 xxxxFHx12500250265xxx -203 0.312 0.562 xxxxFHx12500312265xxx -204 0.375 0.625 xxxxFHx12500375265xxx -205 0.437 0.687 xxxxFHx12500437265xxx -206 0.500 0.750 xxxxFHx12500500265xxx -207 0.562 0.812 xxxxFHx12500562265xxx -208 0.625 0.875 xxxxFHx12500625265xxx -209 0.687 0.937 xxxxFHx12500687265xxx -210 0.750 1.000 xxxxFHx12500750265xxx -211 0.812 1.062 xxxxFHx12500812265xxx -212 0.875 1.125 xxxxFHx12500875265xxx -213 0.937 1.187 xxxxFHx12500937265xxx -214 1.000 1.250 xxxxFHx12501000265xxx -215 1.062 1.312 xxxxFHx12501062265xxx -216 1.125 1.375 xxxxFHx12501125265xxx -217 1.187 1.437 xxxxFHx12501187265xxx -218 1.250 1.500 xxxxFHx12501250265xxx -219 1.312 1.562 xxxxFHx12501312265xxx -220 1.375 1.625 xxxxFHx12501375265xxx -221 1.437 1.687 xxxxFHx12501437265xxx -222 1.500 1.750 xxxxFHx12501500265xxx -223 1.625 1.875 xxxxFHx12501625265xxx -224 1.750 2.000 xxxxFHx12501750265xxx Dash # Dash # -225 -226 -227 -228 -229 -230 -231 -232 -233 -234 -235 -236 -237 -238 -239 -240 -241 -242 -243 -244 -245 -246 -247 -248 -249 -250 -251 -252 -253 -254 -255 -256 -257 -258 -259 A Shaft Diameter 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.250 B Groove Diameter 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.125 6.250 6.500 Part Number xxxxFHx12501875265xxx xxxxFHx12502000265xxx xxxxFHx12502125265xxx xxxxFHx12502250265xxx xxxxFHx12502375265xxx xxxxFHx12502500265xxx xxxxFHx12502625265xxx xxxxFHx12502750265xxx xxxxFHx12502875265xxx xxxxFHx12503000265xxx xxxxFHx12503125265xxx xxxxFHx12503250265xxx xxxxFHx12503375265xxx xxxxFHx12503500265xxx xxxxFHx12503625265xxx xxxxFHx12503750265xxx xxxxFHx12503875265xxx xxxxFHx12504000265xxx xxxxFHx12504125265xxx xxxxFHx12504250265xxx xxxxFHx12504375265xxx xxxxFHx12504500265xxx xxxxFHx12504625265xxx xxxxFHx12504750265xxx xxxxFHx12504875265xxx xxxxFHx12505000265xxx xxxxFHx12505125265xxx xxxxFHx12505250265xxx xxxxFHx12505375265xxx xxxxFHx12505500265xxx xxxxFHx12505625265xxx xxxxFHx12505750265xxx xxxxFHx12505875265xxx xxxxFHx12506000265xxx xxxxFHx12506250265xxx
01/15/07
7-12
www.parkerseals.com

G R
Rotary Seal A B Part Number Shaft Groove Diameter Diameter R = 0.015" max. radius E = 0.002" max. G for FH Seal groove = 0.285/0.295" (265 callout) +.000/ +.002/ -.002 -.000 -260 6.500 6.750 xxxxFHx12506500265xxx -261 6.750 7.000 xxxxFHx12506750265xxx -262 7.000 7.250 xxxxFHx12507000265xxx -263 7.250 7.500 xxxxFHx12507250265xxx -264 7.500 7.750 xxxxFHx12507500265xxx -265 7.750 8.000 xxxxFHx12507750265xxx -266 8.000 8.250 xxxxFHx12508000265xxx -267 8.250 8.500 xxxxFHx12508250265xxx -268 8.500 8.750 xxxxFHx12508500265xxx -269 8.750 9.000 xxxxFHx12508750265xxx -270 9.000 9.250 xxxxFHx12509000265xxx -271 9.250 9.500 xxxxFHx12509250265xxx -272 9.500 9.750 xxxxFHx12509500265xxx -273 9.750 10.000 xxxxFHx12509750265xxx -274 10.000 10.250 xxxxFHx12510000265xxx -275 10.500 10.750 xxxxFHx12510500265xxx -276 11.000 11.250 xxxxFHx12511000265xxx -277 11.500 11.750 xxxxFHx12511500265xxx -278 12.000 12.250 xxxxFHx12512000265xxx -279 12.500 12.750 xxxxFHx12512500265xxx -280 13.000 13.250 xxxxFHx12513000265xxx -281 13.500 13.750 xxxxFHx12513500265xxx R = 0.015" max. radius E = 0.003" max. G for FC Seal groove = 0.281/0.291" (260 callout) G for FH Seal groove = 0.370/0.380" (345 callout) +.000/ +.002/ -.002 -.000 -310 0.500 0.875 xxxxFCx18700500260xxx -311 0.562 0.937 xxxxFCx18700562260xxx -312 0.625 1.000 xxxxFCx18700625260xxx -313 0.687 1.062 xxxxFCx18700687260xxx -314 0.750 1.125 xxxxFCx18700750260xxx -315 0.812 1.187 xxxxFCx18700812260xxx Dash # Dash # -316 -317 -318 -319 -320 -321 -322 -323 -324 -325 -326 -327 -328 -329 -330 -331 -332 -333 -334 -335 -336 -337 -338 -339 -340 -341 -342 -343 -344 -345 -346 -347 -348 -349 -350 -351 A Shaft Diameter 0.875 0.937 1.000 1.062 1.125 1.187 1.250 1.312 1.375 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 B Groove Diameter 1.250 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 Part Number xxxxFCx18700875260xxx xxxxFCx18700937260xxx xxxxFCx18701000260xxx xxxxFCx18701062260xxx xxxxFCx18701125260xxx xxxxFCx18701187260xxx xxxxFCx18701250260xxx xxxxFCx18701312260xxx xxxxFCx18701375260xxx xxxxFCx18701500260xxx xxxxFCx18701625260xxx xxxxFCx18701750260xxx xxxxFCx18701875260xxx xxxxFCx18702000260xxx xxxxFCx18702125260xxx xxxxFCx18702250260xxx xxxxFCx18702375260xxx xxxxFCx18702500260xxx xxxxFCx18702625260xxx xxxxFCx18702750260xxx xxxxFCx18702875260xxx xxxxFCx18703000260xxx xxxxFCx18703125260xxx xxxxFCx18703250260xxx xxxxFCx18703375260xxx xxxxFCx18703500260xxx xxxxFCx18703625260xxx xxxxFCx18703750260xxx xxxxFCx18703875260xxx xxxxFCx18704000260xxx xxxxFCx18704125260xxx xxxxFCx18704250260xxx xxxxFCx18704375260xxx xxxxFCx18704500260xxx xxxxFCx18704625260xxx xxxxFCx18704750260xxx 01/15/07
7-13
www.parkerseals.com

G R
Rotary Seal A B Part Number Shaft Groove Diameter Diameter R = 0.015" max. radius E = 0.003" max. G for FC Seal groove = 0.281/0.291" (260 callout) G for FH Seal groove = 0.370/0.380" (345 callout) +.000/ +.002/ -.002 -.000 -352 4.875 5.250 xxxxFCx18704875260xxx -353 5.000 5.375 xxxxFCx18705000260xxx -354 5.125 5.500 xxxxFCx18705125260xxx -355 5.250 5.625 xxxxFCx18705250260xxx -356 5.375 5.750 xxxxFCx18705375260xxx -357 5.500 5.875 xxxxFCx18705500260xxx -358 5.625 6.000 xxxxFCx18705625260xxx -359 5.750 6.125 xxxxFCx18705750260xxx -360 5.875 6.250 xxxxFCx18705875260xxx -361 6.000 6.375 xxxxFCx18706000260xxx -362 6.250 6.625 xxxxFCx18706250260xxx -363 6.500 6.875 xxxxFCx18706500260xxx -364 6.750 7.125 xxxxFCx18706750260xxx -365 7.000 7.375 xxxxFCx18707000260xxx -366 7.250 7.625 xxxxFCx18707250260xxx -367 7.500 7.875 xxxxFCx18707500260xxx -368 7.750 8.125 xxxxFCx18707750260xxx -369 8.000 8.375 xxxxFCx18708000260xxx -370 8.250 8.625 xxxxFCx18708250260xxx -371 8.500 8.875 xxxxFCx18708500260xxx -372 8.750 9.125 xxxxFCx18708750260xxx -373 9.000 9.375 xxxxFCx18709000260xxx -374 9.250 9.625 xxxxFCx18709250260xxx -375 9.500 9.875 xxxxFCx18709500260xxx -376 9.750 10.125 xxxxFCx18709750260xxx -377 10.000 10.375 xxxxFCx18710000260xxx -378 10.500 10.875 xxxxFCx18710500260xxx -379 11.000 11.375 xxxxFCx18711000260xxx -380 11.500 11.875 xxxxFCx18711500260xxx -381 12.000 12.375 xxxxFCx18712000260xxx -382 13.000 13.375 xxxxFCx18713000260xxx -383 14.000 14.375 xxxxFCx18714000260xxx Dash # A B Part Number Shaft Groove Diameter Diameter -384 15.000 15.375 xxxxFCx18715000260xxx -385 16.000 16.375 xxxxFCx18716000260xxx -386 17.000 17.375 xxxxFCx18717000260xxx -387 18.000 18.375 xxxxFCx18718000260xxx -388 19.000 19.375 xxxxFCx18719000260xxx -389 20.000 20.375 xxxxFCx18720000260xxx -390 21.000 21.375 xxxxFCx18721000260xxx -391 22.000 22.375 xxxxFCx18722000260xxx -392 23.000 23.375 xxxxFCx18723000260xxx -393 24.000 24.375 xxxxFCx18724000260xxx -394 25.000 25.375 xxxxFCx18725000260xxx -395 26.000 26.375 xxxxFCx18726000260xxx R = 0.015" max. radius E = 0.003" max. G for FC Seal groove = 0.375/0.385" (355 callout) G for FH Seal groove = 0.450/0.460" (425 callout) +.000/ +.003/ -.003 -.000 -401 1.500 2.000 xxxxFCx25001500355xxx -402 1.625 2.125 xxxxFCx25001625355xxx -403 1.750 2.250 xxxxFCx25001750355xxx -404 1.875 2.375 xxxxFCx25001875355xxx -405 2.000 2.500 xxxxFCx25002000355xxx -406 2.125 2.625 xxxxFCx25002125355xxx -407 2.250 2.750 xxxxFCx25002250355xxx -408 2.375 2.875 xxxxFCx25002375355xxx -409 2.500 3.000 xxxxFCx25002500355xxx -410 2.625 3.125 xxxxFCx25002625355xxx -411 2.750 3.250 xxxxFCx25002750355xxx -412 2.875 3.375 xxxxFCx25002875355xxx -413 3.000 3.500 xxxxFCx25003000355xxx -414 3.125 3.625 xxxxFCx25003125355xxx -415 3.250 3.750 xxxxFCx25003250355xxx -416 3.375 3.875 xxxxFCx25003375355xxx -417 3.500 4.000 xxxxFCx25003500355xxx -418 3.625 4.125 xxxxFCx25003625355xxx Dash #
01/15/07
7-14
www.parkerseals.com

G R
Rotary Seal A B Part Number Shaft Groove Diameter Diameter R = 0.015" max. radius E = 0.003" max. G for FC Seal groove = 0.375/0.385" (355 callout) G for FH Seal groove = 0.450/0.460" (425 callout) +.000/ +.003/ -.003 -.000 -419 3.750 4.250 xxxxFCx25003750355xxx -420 3.875 4.375 xxxxFCx25003875355xxx -421 4.000 4.500 xxxxFCx25004000355xxx -422 4.125 4.625 xxxxFCx25004125355xxx -423 4.250 4.750 xxxxFCx25004250355xxx -424 4.375 4.875 xxxxFCx25004375355xxx -425 4.500 5.000 xxxxFCx25004500355xxx -426 4.625 5.125 xxxxFCx25004625355xxx -427 4.750 5.250 xxxxFCx25004750355xxx -428 4.875 5.375 xxxxFCx25004875355xxx -429 5.000 5.500 xxxxFCx25005000355xxx -430 5.125 5.625 xxxxFCx25005125355xxx -431 5.250 5.750 xxxxFCx25005250355xxx -432 5.375 5.875 xxxxFCx25005375355xxx -433 5.500 6.000 xxxxFCx25005500355xxx -434 5.625 6.125 xxxxFCx25005625355xxx -435 5.750 6.250 xxxxFCx25005750355xxx -436 5.875 6.375 xxxxFCx25005875355xxx -437 6.000 6.500 xxxxFCx25006000355xxx -438 6.250 6.750 xxxxFCx25006250355xxx -439 6.500 7.000 xxxxFCx25006500355xxx -440 6.750 7.250 xxxxFCx25006750355xxx -441 7.000 7.500 xxxxFCx25007000355xxx -442 7.250 7.750 xxxxFCx25007250355xxx -443 7.500 8.000 xxxxFCx25007500355xxx -444 7.750 8.250 xxxxFCx25007750355xxx Dash # Dash # -445 -446 -447 -448 -449 -450 -451 -452 -453 -454 -455 -456 -457 -458 -459 -460 -461 -462 -463 -464 -465 -466 -467 -468 -469 -470 -471 -472 -473 -474 -475 A Shaft Diameter 8.000 8.500 9.000 9.500 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 14.000 14.500 15.000 15.500 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 20.000 21.000 22.000 23.000 24.000 25.000 26.000 B Groove Diameter 8.500 9.000 9.500 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 14.000 14.500 15.000 15.500 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 20.000 20.500 21.500 22.500 23.500 24.500 25.500 26.500 Part Number xxxxFCx25008000355xxx xxxxFCx25008500355xxx xxxxFCx25009000355xxx xxxxFCx25009500355xxx xxxxFCx25010000355xxx xxxxFCx25010500355xxx xxxxFCx25011000355xxx xxxxFCx25011500355xxx xxxxFCx25012000355xxx xxxxFCx25012500355xxx xxxxFCx25013000355xxx xxxxFCx25013500355xxx xxxxFCx25014000355xxx xxxxFCx25014500355xxx xxxxFCx25015000355xxx xxxxFCx25015500355xxx xxxxFCx25016000355xxx xxxxFCx25016500355xxx xxxxFCx25017000355xxx xxxxFCx25017500355xxx xxxxFCx25018000355xxx xxxxFCx25018500355xxx xxxxFCx25019000355xxx xxxxFCx25019500355xxx xxxxFCx25020000355xxx xxxxFCx25021000355xxx xxxxFCx25022000355xxx xxxxFCx25023000355xxx xxxxFCx25024000355xxx xxxxFCx25025000355xxx xxxxFCx25026000355xxx
01/15/07
7-15
www.parkerseals.com
FlexiSeal Rotary Seals FC and FH Profiles Metric

Metric FC and FH Profiles
FC FlexiSeal Rotary Shaft, Centered O-Ring profiles and FH FlexiSeal Rotary Shaft, O-Ring in Heel profiles are available in Metric sizes on the following page.

Part Number Example

Table 7-9. FC and FH Metric Part Number
M 5 0 2
FC C
0 7 0 0
0 7 5 5 0
0 9 0
Material Code
Cross-Section
Rotary Shaft Centered O-Ring Chamfered ID & OD Lip
Gland ID
Cantilever Spring Spring Load

Rotary Application
All part numbers on the following page call for the standard seal height for pressures below 3000 psi. The heel of a FlexiSeal can be extended to increase extrusion resistance simply by changing the seal height callout in the part number.
M 5 0 2 FC C 0 5 0 0 0 3 3 0 1

Radial Cross-Section 0250 0400 0500 0700 Std. FC Seal Height Callout N/A N/A 066 090 Std. FH Seal Height Callout 050 067 088 108
0 6 6
Seal Height
Note: FH profiles are available in extended heel only.
.
M 5 0 2 FC C 0 5 0 0 0 3 3 0 1
0 7 9
Seal Height
01/15/07
7-16
www.parkerseals.com
FlexiSeal Rotary Seals Gland Dimensions Metric FC & FH Profiles
FC and FH Profiles Metric
Table 7-10. FC and FH Metric Gland Dimensions

G R0.38
E**
A (h9)* B (H9)*
Rotary Seal
FC part numbers are available only in 0500 (5 mm) cross-section and higher.
CrossSection Callout 0250 0400 0500 0700
Gland FC Seal CrossHeight Section Callout 2.50 mm N/A 4.00 mm N/A 5.00 mm 066 7.00 mm 090
FH Seal FC FH Height Groove Width (G) Groove Width (G) Callout +0.25/-0.00 mm +0.25/-0.00 mm 050 N/A 15.33 mm 067 N/A 17.24 mm 088 7.14 mm 19.40 mm 108 9.53 mm 11.43 mm
** For ISO Tolerances see Appendix D. ** See Page 2-10 for more on extrusion gap.

FCC-V FCS-V Part Number Shaft (A) in mm Groove fl (B) in mm Groove Width (G) in mm FCS-V Profile M301FCS070006504090EVM 65.04 + .00/-.07 79.04 + .07/-.00 9.53 + 0.25/-.00 FHC-C Profile M602FHC040002900067SCL 29.00 + .00/-.052 37.00 + .062/-.00 7.24 + 0.25/-.00
FCC-C
FCS-C
FH part numbers are available in extended heel only.
FHC-V
FHS-V
FHC-C
FHS-C
01/15/07
7-17
www.parkerseals.com
FlexiSeal Rotary Seals FF Profiles Flanged Inch/Fractional

FF Profiles
FF FlexiSeal Rotary Shaft, Flanged profiles are clamped axially in the gland to ensure that the seal does not spin with the shaft, especially in applications with frequent thermal cycling.
Flanged FlexiSeals
Part Number Example

Table 7-11. FF Flanged Inch/Fractional Part Number
0 5 0 2
FF C
1 2 5
0 1 2 5 0
1 7 0
Flanged Rotary Application
Rotary Shaft Flanged Chamfered ID & OD Lip
Cantilever Spring
01/15/07
7-18
www.parkerseals.com
FlexiSeal Rotary Seals Gland Dimensions FF Profiles, Flanged

Table 7-12. FF Flanged Inch/Fractional Gland Dimensions
FF Profiles Flanged Inch/Fractional
G D
40
K E
C Counterbore
R
Flanged Seal
FFC-V
FFS-V
FFC-C
FFS-C
FFN-H
C Flange B Part Number Groove C-Bore Dia. Dia. Min. R = 0.015" max. radius E = 0.002" max. K = 0.017" Ref. G for Standard heel groove = 0.094/0.104" (083 callout) D Gland Counterbore depth for seal flange = 0.011/0.013" +.000/ +.002/ -.002 -.000 -006 0.125 0.250 0.400 xxxxFFx06200125083xxx -007 0.156 0.281 0.431 xxxxFFx06200156083xxx -008 0.187 0.312 0.462 xxxxFFx06200187083xxx -009 0.218 0.343 0.493 xxxxFFx06200218083xxx -010 0.250 0.375 0.525 xxxxFFx06200250083xxx -011 0.312 0.437 0.587 xxxxFFx06200312083xxx -012 0.375 0.500 0.650 xxxxFFx06200375083xxx -013 0.437 0.562 0.712 xxxxFFx06200437083xxx -014 0.500 0.625 0.775 xxxxFFx06200500083xxx -015 0.562 0.687 0.837 xxxxFFx06200562083xxx -016 0.625 0.750 0.900 xxxxFFx06200625083xxx -017 0.687 0.812 0.962 xxxxFFx06200687083xxx -018 0.750 0.875 1.025 xxxxFFx06200750083xxx -019 0.812 0.937 1.087 xxxxFFx06200812083xxx -020 0.875 1.000 1.150 xxxxFFx06200875083xxx -021 0.937 1.062 1.212 xxxxFFx06200937083xxx -022 1.000 1.125 1.275 xxxxFFx06201000083xxx -023 1.062 1.187 1.337 xxxxFFx06201062083xxx -024 1.125 1.250 1.400 xxxxFFx06201125083xxx -025 1.187 1.312 1.462 xxxxFFx06201187083xxx -026 1.250 1.375 1.525 xxxxFFx06201250083xxx -027 1.312 1.437 1.587 xxxxFFx06201312083xxx -028 1.375 1.500 1.650 xxxxFFx06201375083xxx -029 1.500 1.625 1.775 xxxxFFx06201500083xxx -030 1.625 1.750 1.900 xxxxFFx06201625083xxx -031 1.750 1.875 2.025 xxxxFFx06201750083xxx Dash # A Shaft Dia. 01/15/06
7-19
www.parkerseals.com

Table 7-12. FF Flanged Inch/Fractional Gland Dimensions (Continued)
G D
40
K E
C Counterbore
R
Flanged Seal C B Flange Part Number Groove C-Bore Dia. Dia. Min. R = 0.015" max. radius E = 0.002" max. K = 0.017" Ref. G for Standard heel groove = 0.094/0.104" (083 callout) D Gland Counterbore depth for seal flange = 0.011/0.013" +.000/ +.002/ -.002 -.000 -032 1.875 2.000 2.150 xxxxFFx06201875083xxx -033 2.000 2.125 2.275 xxxxFFx06202000083xxx -034 2.125 2.250 2.400 xxxxFFx06202125083xxx -035 2.250 2.375 2.525 xxxxFFx06202250083xxx -036 2.375 2.500 2.650 xxxxFFx06202375083xxx -037 2.500 2.625 2.775 xxxxFFx06202500083xxx -038 2.625 2.750 2.900 xxxxFFx06202625083xxx -039 2.750 2.875 3.025 xxxxFFx06202750083xxx -040 2.875 3.000 3.150 xxxxFFx06202875083xxx -041 3.000 3.125 3.275 xxxxFFx06203000083xxx -042 3.250 3.375 3.525 xxxxFFx06203250083xxx -043 3.500 3.625 3.775 xxxxFFx06203500083xxx -044 3.750 3.875 4.025 xxxxFFx06203750083xxx -045 4.000 4.125 4.275 xxxxFFx06204000083xxx R = 0.015" max. radius E = 0.002" max. K = 0.028" Ref. G for Standard heel groove = 0.141/0.151" (130 callout) D Gland Counterbore depth for seal flange = 0.017/0.020" +.000/ +.002/ -.002 -.000 -106 0.187 0.375 0.530 xxxxFFx09300187130xxx -107 0.219 0.406 0.561 xxxxFFx09300219130xxx -108 0.250 0.437 0.592 xxxxFFx09300250130xxx -109 0.312 0.500 0.655 xxxxFFx09300312130xxx -110 0.375 0.562 0.717 xxxxFFx09300375130xxx -111 0.437 0.625 0.780 xxxxFFx09300437130xxx -112 0.500 0.687 0.842 xxxxFFx09300500130xxx -113 0.562 0.750 0.905 xxxxFFx09300562130xxx -114 0.625 0.812 0.967 xxxxFFx09300625130xxx -115 0.687 0.875 1.030 xxxxFFx09300687130xxx -116 0.750 0.937 1.092 xxxxFFx09300750130xxx -117 0.812 1.000 1.155 xxxxFFx09300812130xxx Dash # A Shaft Dia. Dash # -118 -119 -120 -121 -122 -123 -124 -125 -126 -127 -128 -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -151 A Shaft Dia. 0.875 0.937 1.000 1.062 1.125 1.187 1.250 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.812 1.875 1.937 2.000 2.062 2.125 2.187 2.250 2.312 2.375 2.437 2.500 2.562 2.625 2.687 2.750 2.812 2.875 3.000 C B Flange Groove C-Bore Dia. Dia. Min. 1.062 1.217 1.125 1.280 1.187 1.342 1.250 1.405 1.312 1.467 1.375 1.530 1.437 1.592 1.500 1.655 1.562 1.717 1.625 1.780 1.687 1.842 1.750 1.905 1.812 1.967 1.875 2.030 1.937 2.092 2.000 2.155 2.062 2.217 2.125 2.280 2.187 2.342 2.250 2.405 2.312 2.467 2.375 2.530 2.437 2.592 2.500 2.655 2.562 2.717 2.625 2.780 2.687 2.842 2.750 2.905 2.812 2.967 2.875 3.030 2.937 3.092 3.000 3.155 3.062 3.217 3.187 3.342
Part Number xxxxFFx09300875130xxx xxxxFFx09300937130xxx xxxxFFx09301000130xxx xxxxFFx09301062130xxx xxxxFFx09301125130xxx xxxxFFx09301187130xxx xxxxFFx09301250130xxx xxxxFFx09301312130xxx xxxxFFx09301375130xxx xxxxFFx09301437130xxx xxxxFFx09301500130xxx xxxxFFx09301562130xxx xxxxFFx09301625130xxx xxxxFFx09301687130xxx xxxxFFx09301750130xxx xxxxFFx09301812130xxx xxxxFFx09301875130xxx xxxxFFx09301937130xxx xxxxFFx09302000130xxx xxxxFFx09302062130xxx xxxxFFx09302125130xxx xxxxFFx09302187130xxx xxxxFFx09302250130xxx xxxxFFx09302312130xxx xxxxFFx09302375130xxx xxxxFFx09302437130xxx xxxxFFx09302500130xxx xxxxFFx09302562130xxx xxxxFFx09302625130xxx xxxxFFx09302687130xxx xxxxFFx09302750130xxx xxxxFFx09302812130xxx xxxxFFx09302875130xxx xxxxFFx09303000130xxx 01/15/06
7-20
www.parkerseals.com

G D
40
K E
C Counterbore
R
Flanged Seal C B Flange Groove C-Bore Part Number Dia. Dia. Min. R = 0.015" max. radius E = 0.002" max. K = 0.028" Ref. G for Standard heel groove = 0.141/0.151" (130 callout) D Gland Counterbore depth for seal flange = 0.017/0.020" +.000/ +.002/ -.002 -.000 -152 3.250 3.437 3.592 xxxxFFx09303250130xxx -153 3.500 3.687 3.842 xxxxFFx09303500130xxx -154 3.750 3.937 4.092 xxxxFFx09303750130xxx -155 4.000 4.187 4.342 xxxxFFx09304000130xxx -156 4.250 4.437 4.592 xxxxFFx09304250130xxx -157 4.500 4.687 4.842 xxxxFFx09304500130xxx -158 4.750 4.937 5.092 xxxxFFx09304750130xxx -159 5.000 5.187 5.342 xxxxFFx09305000130xxx -160 5.250 5.437 5.592 xxxxFFx09305250130xxx -161 5.500 5.687 5.842 xxxxFFx09305500130xxx -162 5.750 5.928 6.083 xxxxFFx09305750130xxx -163 6.000 6.187 6.342 xxxxFFx09306000130xxx R = 0.015" max. radius E = 0.002" max. K = 0.040" Ref. G for Standard heel groove = 0.188/0.198" (170 callout) D Gland Counterbore depth for seal flange = 0.024/0.027" +.000/ +.002/ -.002 -.000 -202 0.250 0.500 0.687 xxxxFFx12500250170xxx -203 0.312 0.562 0.749 xxxxFFx12500312170xxx -204 0.375 0.625 0.812 xxxxFFx12500375170xxx -205 0.437 0.687 0.874 xxxxFFx12500437170xxx -206 0.500 0.750 0.937 xxxxFFx12500500170xxx -207 0.562 0.812 0.999 xxxxFFx12500562170xxx -208 0.625 0.875 1.062 xxxxFFx12500625170xxx -209 0.687 0.937 1.124 xxxxFFx12500687170xxx -210 0.750 1.000 1.187 xxxxFFx12500750170xxx -211 0.812 1.062 1.249 xxxxFFx12500812170xxx -212 0.875 1.125 1.312 xxxxFFx12500875170xxx -213 0.937 1.187 1.374 xxxxFFx12500937170xxx Dash # A Shaft Dia. Dash # -214 -215 -216 -217 -218 -219 -220 -221 -222 -223 -224 -225 -226 -227 -228 -229 -230 -231 -232 -233 -234 -235 -236 -237 -238 -239 -240 -241 -242 -243 -244 -245 A Shaft Dia. 1.000 1.062 1.125 1.187 1.250 1.312 1.375 1.437 1.500 1.625 1.750 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 C B Flange Groove C-Bore Dia. Dia. Min. 1.250 1.437 1.312 1.499 1.375 1.562 1.437 1.624 1.500 1.687 1.562 1.749 1.625 1.812 1.687 1.874 1.750 1.937 1.875 2.062 2.000 2.187 2.125 2.312 2.250 2.437 2.375 2.562 2.500 2.687 2.625 2.812 2.750 2.937 2.875 3.062 3.000 3.187 3.125 3.312 3.250 3.437 3.375 3.562 3.500 3.687 3.625 3.812 3.750 3.937 3.875 4.062 4.000 4.187 4.125 4.312 4.250 4.437 4.375 4.562 4.500 4.687 4.625 4.812
Part Number xxxxFFx12501000170xxx xxxxFFx12501062170xxx xxxxFFx12501125170xxx xxxxFFx12501187170xxx xxxxFFx12501250170xxx xxxxFFx12501312170xxx xxxxFFx12501375170xxx xxxxFFx12501437170xxx xxxxFFx12501500170xxx xxxxFFx12501625170xxx xxxxFFx12501750170xxx xxxxFFx12501875170xxx xxxxFFx12502000170xxx xxxxFFx12502125170xxx xxxxFFx12502250170xxx xxxxFFx12502375170xxx xxxxFFx12502500170xxx xxxxFFx12502625170xxx xxxxFFx12502750170xxx xxxxFFx12502875170xxx xxxxFFx12503000170xxx xxxxFFx12503125170xxx xxxxFFx12503250170xxx xxxxFFx12503375170xxx xxxxFFx12503500170xxx xxxxFFx12503625170xxx xxxxFFx12503750170xxx xxxxFFx12503875170xxx xxxxFFx12504000170xxx xxxxFFx12504125170xxx xxxxFFx12504250170xxx xxxxFFx12504375170xxx
01/15/07
7-21
www.parkerseals.com

G D
40
K E
C Counterbore
R
Flanged Seal Dash # A Shaft Dia. C B Flange Groove C-Bore Dia. Dia. Min. Dash # -274 -275 -276 -277 -278 4.937 5.062 5.187 5.312 5.437 5.562 5.687 5.812 5.937 6.062 6.187 6.312 6.437 6.687 6.937 7.187 7.437 7.687 7.937 8.187 8.437 8.687 8.937 9.187 9.437 9.687 9.937 10.187 xxxxFFx12504500170xxx xxxxFFx12504625170xxx xxxxFFx12504750170xxx xxxxFFx12504875170xxx xxxxFFx12505000170xxx xxxxFFx12505125170xxx xxxxFFx12505250170xxx xxxxFFx12505375170xxx xxxxFFx12505500170xxx xxxxFFx12505625170xxx xxxxFFx12505750170xxx xxxxFFx12505875170xxx xxxxFFx12506000170xxx xxxxFFx12506250170xxx xxxxFFx12506500170xxx xxxxFFx12506750170xxx xxxxFFx12507000170xxx xxxxFFx12507250170xxx xxxxFFx12507500170xxx xxxxFFx12507750170xxx xxxxFFx12508000170xxx xxxxFFx12508250170xxx xxxxFFx12508500170xxx xxxxFFx12508750170xxx xxxxFFx12509000170xxx xxxxFFx12509250170xxx xxxxFFx12509500170xxx xxxxFFx12509750170xxx 01/15/07 -310 -311 -312 -313 -314 -315 -316 -317 -318 -319 -320 -321 -322 -323 -324 -325 -326 -327 -279 -280 -281 A Shaft Dia. 10.000 10.500 11.000 11.500 12.000 12.500 13.000 13.500 C B Flange Groove C-Bore Dia. Dia. Min. 10.250 10.750 11.250 11.750 12.250 12.750 13.250 13.750 10.437 10.937 11.437 11.937 12.437 12.937 13.437 13.937
Part Number
Part Number
R = 0.015" max. radius E = 0.002" max. K = 0.040" Ref. G for Standard heel groove = 0.188/0.198" (170 callout) D Gland Counterbore depth for seal flange = 0.024/0.027" +.000/ -.002 -246 -247 -248 -249 -250 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.250 8.500 8.750 9.000 9.250 9.500 9.750 +.002/ -.000 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.125 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.250 8.500 8.750 9.000 9.250 9.500 9.750 10.000
xxxxFFx12510000170xxx xxxxFFx12510500170xxx xxxxFFx12511000170xxx xxxxFFx12511500170xxx xxxxFFx12512000170xxx xxxxFFx12512500170xxx xxxxFFx12513000170xxx xxxxFFx12513500170xxx
-251 -252 -253 -254 -255 -256 -257 -258 -259 -260 -261 -262 -263 -264 -265 -266 -267 -268 -269 -270 -271 -272 -273
R = 0.015" max. radius E = 0.003" max. K = 0.057" Ref. G for Standard heel groove = 0.281/0.291" (260 callout) D Gland Counterbore depth for seal flange = 0.028/0.032" +.000/ -.002 0.500 0.562 0.625 0.687 0.750 0.812 0.875 0.937 1.000 1.062 1.125 1.187 1.250 1.312 1.375 1.500 1.625 1.750 +.002/ -.000 0.875 0.937 1.000 1.062 1.125 1.187 1.250 1.312 1.375 1.437 1.500 1.562 1.625 1.687 1.750 1.875 2.000 2.125 1.166 1.228 1.291 1.353 1.416 1.478 1.541 1.603 1.666 1.728 1.791 1.853 1.916 1.978 2.041 2.166 2.291 2.416 xxxxFFx18700500260xxx xxxxFFx18700562260xxx xxxxFFx18700625260xxx xxxxFFx18700687260xxx xxxxFFx18700750260xxx xxxxFFx18700812260xxx xxxxFFx18700875260xxx xxxxFFx18700937260xxx xxxxFFx18701000260xxx xxxxFFx18701062260xxx xxxxFFx18701125260xxx xxxxFFx18701187260xxx xxxxFFx18701250260xxx xxxxFFx18701312260xxx xxxxFFx18701375260xxx xxxxFFx18701500260xxx xxxxFFx18701625260xxx xxxxFFx18701750260xxx
7-22
www.parkerseals.com

G D
40
K E
C Counterbore
R
Flanged Seal Dash # A Shaft Dia. C Flange B Groove C-Bore Dia. Dia. Min. Dash # -356 -357 -358 -359 -360 2.541 2.666 2.791 2.916 3.041 3.166 3.291 3.416 3.541 3.666 3.791 3.916 4.041 4.166 4.291 4.416 4.541 4.666 4.791 4.916 5.041 5.166 5.291 5.416 5.541 5.666 5.791 5.916 xxxxFFx18701875260xxx xxxxFFx18702000260xxx xxxxFFx18702125260xxx xxxxFFx18702250260xxx xxxxFFx18702375260xxx xxxxFFx18702500260xxx xxxxFFx18702625260xxx xxxxFFx18702750260xxx xxxxFFx18702875260xxx xxxxFFx18703000260xxx xxxxFFx18703125260xxx xxxxFFx18703250260xxx xxxxFFx18703375260xxx xxxxFFx18703500260xxx xxxxFFx18703625260xxx xxxxFFx18703750260xxx xxxxFFx18703875260xxx xxxxFFx18704000260xxx xxxxFFx18704125260xxx xxxxFFx18704250260xxx xxxxFFx18704375260xxx xxxxFFx18704500260xxx xxxxFFx18704625260xxx xxxxFFx18704750260xxx xxxxFFx18704875260xxx xxxxFFx18705000260xxx xxxxFFx18705125260xxx xxxxFFx18705250260xxx 01/15/06 -361 -362 -363 -364 -365 -366 -367 -368 -369 -370 -371 -372 -373 -374 -375 -376 -377 -378 -379 -380 -381 -382 -383 -384 -385 -386 -387 A Shaft Dia. 5.375 5.500 5.625 5.750 5.875 6.000 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.250 8.500 8.750 9.000 9.250 9.500 9.750 10.000 10.500 11.000 11.500 12.000 13.000 14.000 15.000 16.000 17.000 18.000 C Flange B Groove C-Bore Dia. Dia. Min. 5.750 5.875 6.000 6.125 6.250 6.375 6.625 6.875 7.125 7.375 7.625 7.875 8.125 8.375 8.625 8.875 9.125 9.375 9.625 9.875 10.125 10.375 10.875 11.375 11.875 12.375 13.375 14.375 15.375 16.375 17.375 18.375 6.041 6.166 6.291 6.416 6.541 6.666 6.916 7.166 7.416 7.666 7.916 8.166 8.416 8.666 8.916 9.166 9.416 9.666 9.916 10.166 10.416 10.666 11.166 11.666 12.166 12.666 13.666 14.666 15.666 16.666 17.666 18.666
Part Number
Part Number
R = 0.015" max. radius E = 0.003" max. K = 0.057" Ref. G for Standard heel groove = 0.281/0.291" (260 callout) D Gland Counterbore depth for seal flange = 0.028/0.032" +.000/ -.002 -328 -329 -330 -331 -332 -333 -334 -335 -336 -337 -338 -339 -340 -341 -342 -343 -344 -345 -346 -347 -348 -349 -350 -351 -352 -353 -354 -355 1.875 2.000 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 +.002/ -.000 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625
xxxxFFx18705375260xxx xxxxFFx18705500260xxx xxxxFFx18705625260xxx xxxxFFx18705750260xxx xxxxFFx18705875260xxx xxxxFFx18706000260xxx xxxxFFx18706250260xxx xxxxFFx18706500260xxx xxxxFFx18706750260xxx xxxxFFx18707000260xxx xxxxFFx18707250260xxx xxxxFFx18707500260xxx xxxxFFx18707750260xxx xxxxFFx18708000260xxx xxxxFFx18708250260xxx xxxxFFx18708500260xxx xxxxFFx18708750260xxx xxxxFFx18709000260xxx xxxxFFx18709250260xxx xxxxFFx18709500260xxx xxxxFFx18709750260xxx xxxxFFx18710000260xxx xxxxFFx18710500260xxx xxxxFFx18711000260xxx xxxxFFx18711500260xxx xxxxFFx18712000260xxx xxxxFFx18713000260xxx xxxxFFx18714000260xxx xxxxFFx18715000260xxx xxxxFFx18716000260xxx xxxxFFx18717000260xxx xxxxFFx18718000260xxx
7-23
www.parkerseals.com

G D
40
K E
C Counterbore
R
Flanged Seal C Flange B Groove C-Bore Part Number Dia. Dia. Min. R = 0.015" max. radius E = 0.003" max. K = 0.057" Ref. G for Standard heel groove = 0.281/0.291" (260 callout) D Gland Counterbore depth for seal flange = 0.028/0.032" +.000/ +.002/ -.002 -.000 -388 19.000 19.375 19.666 xxxxFFx18719000260xxx -389 20.000 20.375 20.666 xxxxFFx18720000260xxx -390 21.000 21.375 21.666 xxxxFFx18721000260xxx -391 22.000 22.375 22.666 xxxxFFx18722000260xxx -392 23.000 23.375 23.666 xxxxFFx18723000260xxx -393 24.000 24.375 24.666 xxxxFFx18724000260xxx -394 25.000 25.375 25.666 xxxxFFx18725000260xxx -395 26.000 26.375 26.666 xxxxFFx18726000260xxx R = 0.015" max. radius E = 0.003" max. K = 0.069" Ref. G for Standard heel groove = 0.375/0.385" (355 callout) D Gland Counterbore depth for seal flange = 0.041/0.045" +.000/ +.002/ -.002 -.000 -401 1.500 2.000 2.322 xxxxFFx25001500355xxx -402 1.625 2.125 2.447 xxxxFFx25001625355xxx -403 1.750 2.250 2.572 xxxxFFx25001750355xxx -404 1.875 2.375 2.697 xxxxFFx25001875355xxx -405 2.000 2.500 2.822 xxxxFFx25002000355xxx -406 2.125 2.625 2.947 xxxxFFx25002125355xxx -407 2.250 2.750 3.072 xxxxFFx25002250355xxx -408 2.375 2.875 3.197 xxxxFFx25002375355xxx -409 2.500 3.000 3.322 xxxxFFx25002500355xxx -410 2.625 3.125 3.447 xxxxFFx25002625355xxx -411 2.750 3.250 3.572 xxxxFFx25002750355xxx -412 2.875 3.375 3.697 xxxxFFx25002875355xxx -413 3.000 3.500 3.822 xxxxFFx25003000355xxx -414 3.125 3.625 3.947 xxxxFFx25003125355xxx -415 3.250 3.750 4.072 xxxxFFx25003250355xxx -416 3.375 3.875 4.197 xxxxFFx25003375355xxx Dash # A Shaft Dia. Dash # -417 -418 -419 -420 -421 -422 -423 -424 -425 -426 -427 -428 -429 -430 -431 -432 -433 -434 -435 -436 -437 -438 -439 -440 -441 -442 -443 -444 -445 -446 -447 -448 -449 -450 A Shaft Dia. 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 5.125 5.250 5.375 5.500 5.625 5.750 5.875 6.000 6.250 6.500 6.750 7.000 7.250 7.500 7.750 8.000 8.500 9.000 9.500 10.000 10.500 C Flange B Groove C-Bore Dia. Dia. Min. 4.000 4.322 4.125 4.447 4.250 4.572 4.375 4.697 4.500 4.822 4.625 4.947 4.750 5.072 4.875 5.197 5.000 5.322 5.125 5.447 5.250 5.572 5.375 5.697 5.500 5.822 5.625 5.947 5.750 6.072 5.875 6.197 6.000 6.322 6.125 6.447 6.250 6.572 6.375 6.697 6.500 6.822 6.750 7.072 7.000 7.322 7.250 7.572 7.500 7.822 7.750 8.072 8.000 8.322 8.250 8.572 8.500 8.822 9.000 9.322 9.500 9.822 10.000 10.322 10.500 10.822 11.000 11.322
Part Number xxxxFFx25003500355xxx xxxxFFx25003625355xxx xxxxFFx25003750355xxx xxxxFFx25003875355xxx xxxxFFx25004000355xxx xxxxFFx25004125355xxx xxxxFFx25004250355xxx xxxxFFx25004375355xxx xxxxFFx25004500355xxx xxxxFFx25004625355xxx xxxxFFx25004750355xxx xxxxFFx25004875355xxx xxxxFFx25005000355xxx xxxxFFx25005125355xxx xxxxFFx25005250355xxx xxxxFFx25005375355xxx xxxxFFx25005500355xxx xxxxFFx25005625355xxx xxxxFFx25005750355xxx xxxxFFx25005875355xxx xxxxFFx25006000355xxx xxxxFFx25006250355xxx xxxxFFx25006500355xxx xxxxFFx25006750355xxx xxxxFFx25007000355xxx xxxxFFx25007250355xxx xxxxFFx25007500355xxx xxxxFFx25007750355xxx xxxxFFx25008000355xxx xxxxFFx25008500355xxx xxxxFFx25009000355xxx xxxxFFx25009500355xxx xxxxFFx25010000355xxx xxxxFFx25010500355xxx 01/15/06
7-24
www.parkerseals.com

G D
40
K E
C Counterbore
R
Flanged Seal C B Flange Part Number Groove C-Bore Dia. Dia. Min. R = 0.015" max. radius E = 0.003" max. K = 0.069" Ref. G for Standard heel groove = 0.375/0.385" (355 callout) D Gland Counterbore depth for seal flange = 0.041/0.045" +.000/ +.002/ -.002 -.000 -451 11.000 11.500 11.822 xxxxFFx25011000355xxx -452 11.500 12.000 12.322 xxxxFFx25011500355xxx -453 12.000 12.500 12.822 xxxxFFx25012000355xxx -454 12.500 13.000 13.322 xxxxFFx25012500355xxx -455 13.000 13.500 13.822 xxxxFFx25013000355xxx -456 13.500 14.000 14.322 xxxxFFx25013500355xxx -457 14.000 14.500 14.822 xxxxFFx25014000355xxx -458 14.500 15.000 15.322 xxxxFFx25014500355xxx -459 15.000 15.500 15.822 xxxxFFx25015000355xxx -460 15.500 16.000 16.322 xxxxFFx25015500355xxx Dash # A Shaft Dia. A Shaft Dia. 16.000 16.500 17.000 17.500 18.000 18.500 19.000 19.500 20.000 21.000 22.000 23.000 24.000 25.000 26.000 C B Flange Groove C-Bore Dia. Dia. Min. 16.500 16.822 17.000 17.322 17.500 17.822 18.000 18.322 18.500 18.822 19.000 19.322 19.500 19.822 20.000 20.322 20.500 20.822 21.500 21.822 22.500 22.822 23.500 23.822 24.500 24.822 25.500 25.822 26.500 26.822
Dash # -461 -462 -463 -464 -465 -466 -467 -468 -469 -470 -471 -472 -473 -474 -475
Part Number xxxxFFx25016000355xxx xxxxFFx25016500355xxx xxxxFFx25017000355xxx xxxxFFx25017500355xxx xxxxFFx25018000355xxx xxxxFFx25018500355xxx xxxxFFx25019000355xxx xxxxFFx25019500355xxx xxxxFFx25020000355xxx xxxxFFx25021000355xxx xxxxFFx25022000355xxx xxxxFFx25023000355xxx xxxxFFx25024000355xxx xxxxFFx25025000355xxx xxxxFFx25026000355xxx
01/15/06
7-25
www.parkerseals.com
FlexiSeal Rotary Seals FF Profiles Flanged Metric

Metric FF Profiles
FF FlexiSeal Rotary Shaft, Flanged profiles are clamped axially in the gland to ensure that the seal does not spin with the shaft, especially in applications with frequent thermal cycling.
Flanged FlexiSeal
Part Number Example

Table 7-13. FF Flanged Metric Part Number
M 5 0 2
FF C
0 5 0 0
1 0 5 0 0
0 5 6
7
Flanged Rotary Application
Material Code
Cross-Section
Rotary Shaft Flanged Chamfered ID & OD Lip
Gland ID
Cantilever Spring Spring Load
01/15/06
7-26
www.parkerseals.com
FlexiSeal Rotary Seals Gland Dimensions FF Profiles, Flanged Metric
FF Profiles Flanged Metric
Table 7-14. FF Flanged Metric Gland Dimensions

G D
40
K E
C Counterbore
A (h9)* B (H9)*
R0.38
Flanged Seal
FFC-V
FFS-V
CounterCross- Gland Heel Heel Groove CounterBore Min. Section Cross- Height Width (G) Bore Diameter Callout Section Callout +0.25/-0.00 mm Depth (D) (C) 0200 2.00 mm 021 2.39 mm 0.28/0.33 A + mm 7.81 mm 0250 2.50 mm 033 3.58 mm 0.43/0.51 A + mm 8.94 mm 0400 4.00 mm 043 4.78 mm 0.61/0.69 A + mm 12.75 mm 0500 5.00 mm 066 7.14 mm 0.71/0.81 A + mm 17.39 mm 0700 7.00 mm 090 9.53 mm 1.04/1.14 A + mm 22.18 mm ** For ISO Tolerances see Appendix D. ** See Page 2-10 for more on extrusion gap.
Chamfer Size (K) 0.43 mm 0.71 mm 1.02 mm 1.45 mm 1.75 mm

FFC-C FFS-C Part Number Shaft (A) in mm Groove Counter- Counter- Groove Bore Bore Width (B) in (C) in Depth (D) (G) in mm mm mm in mm 139.00 147.18 +.10/-.00 Min. 15.00 18.81 +.04/-.00 Min. 1.04/1.14 9.53 +0.25/-.00 0.28/0.33 2.39 +0.25/-.00
FFN-H
FFC-V Profile M100FFC070012500090SVL 125.00 +.00/-.10 FFS-C Profile M301FFS020001100021HCH 11.00 +.00/-.04
01/15/06
7-27
www.parkerseals.com
Notes
7-28
www.parkerseals.com
FlexiLip Rotary Seals Introduction

Contents
Engineering . . . . . . . . . . . . . . . . . Materials . . . . . . . . . . . . . . . . . . . Product Offering . . . . . . . . . . . . . 8-3 8-6 8-7
What Is a FlexiLip and How Does It Work?
The Parker FlexiLip is a rotary lip seal that features an ID lip that seals dynamically on a shaft and an elastomeric O-ring on its OD to seal statically in a bore. Since the lip is not spring energized, the radial lip contact forces are lower than a rotary FlexiSeal, which allows the seal to function at much higher surface speeds (up to 5000 sfpm). The seals are manufactured from a wide variety of PTFE composites and other machinable plastic materials. Standard O-ring choices are fluorocarbon, silicone, nitrile and EPDM. This broad foundation of standard O-ring and PTFE materials can be tailored to suit nearly all applications. Standard and Non-standard FlexiLip profiles are precision machined to fit inch-fractional and metric gland geometries. The FlexiLip design is extremely versatile because the seal is machined from a molded PTFE sleeve. Standard tooling and programs are used to manufacture seals efficiently by eliminating setup and programming time. FlexiLip seals are used in demanding applications where the operating conditions exceed the capabilities of elastomeric seals.
FlexiLip
FlexiLip Application
Applications
The FlexiLips versatility makes it suitable for a wide range of applications including:
Motors Gear Boxes Pumps Bearings Compressors Cryogenics Rolls Extruders Valves Blowers Spindles Robotics Mixers
Excluder PTFE Body Lip
Rubber O-Ring Primary Lip
Markets
FlexiLips low tooling costs and rapid prototyping capability make the FlexiLip an appealing choice for customers in a variety of markets including:
Aerospace Automotive Chemical Process Appliances Machine Tools Marine Medical Pharmaceutical Military Heavy Machinery Pulp & Paper Hydraulic Food Processing Electronic Oil & Gas Steel Mill Plastics
FlexiLip Components
01/15/06
8-1
www.parkerseals.com
Introduction Part Number Nomenclature FlexiLip

Table 8-1. FlexiLip Part Number Nomenclature
English 0 5 0 2 LF N 3 7 5 0 2 5 0 0 2 5 0 N S
Gland Cross-Section Examples: 250 = 0.250" 375 = 0.375" 750 = 0.750" Excluder Lip Designation E = Excluder Lip N = No Excluder Lip FlexiLip Lip Style Designation LF = Mandrel Formed Lip LM = Machined Lip LE = Elf-Shoe Lip LD = Dual Lips LG = Garter Spring Lip Shaft Diameter Examples: 00500 = 0.500" 02500 = 2.500" 11000 = 11.000"
Seal Height Designation 250 = 0.250" 375 = 0.375" 750 = 0.750" O-Ring Material Designation N= Nitrile (NBR) V= Fluorocarbon V= (FKM) E= EPDM S= Silicone Metal Band Designation S = Stainless Steel Band N = No Metal Band
Metric M 5 0 2 LF N 1 4 0 0 1 2 0 0 0 2 0 0 N S
Gland Cross-Section Examples: 0900 = 9.00 mm 1250 = 12.50 mm 1400 = 14.00 mm Excluder Lip Designation E = Excluder Lip N = No Excluder Lip Shaft Diameter Examples: 00505 = 5.05 mm 05050 = 50.50 mm 12000 = 120.00 mm
Seal Height Designation 090 = 9.0 mm 200 = 20.0 mm 384 = 38.4 mm O-Ring Material Designation N= Nitrile (NBR) V= Fluorocarbon V= (FKM) E= EPDM S= Silicone Metal Band Designation S = Stainless Steel Band N = No Metal Band
FlexiLip Lip Style Designation LF = Mandrel Formed Lip LM = Machined Lip LE = Elf-Shoe Lip LD = Dual Lips LG = Garter Spring Lip
LFN-N
LEN-N
LDN-N
LMN-N
LFE-N
LEE-N
LDE-N
LGN-N
LFN-S
LEN-S
LDN-S
LMN-S
LFE-S
LEE-S
LDE-S
LGN-S 01/15/06
8-2
www.parkerseals.com
FlexiLip Rotary Seals Engineering

From Gland Dimensions to Part Number
Step 1 Choose profile. Choose the best profile for your application from the decision tree and table on Pages 8-7 through 8-9, and place the 4-character profile description into the part number as shown here in this example. Choice: LEN-S Profile XXXXLENXXXXXXXXXXXXS Step 2 Choose material. Choose the best material for the application and place the 4-digit material code into the part number as shown here: Choice: 0502 Carbon Fiber Filled PTFE 0502LENXXXXXXXXXXXXS Step 3 Choose O-ring material. Choose the best O-ring material after considering the chemicals and temperatures it will be exposed to. Consult the Parker O-Ring Handbook (ORD 5700A/US section II) as a general reference and choose the most appropriate material family. Place in the part number as shown here: Choice: Fluorocarbon O-ring (V code) 0502LENXXXXXXXXXXXVS Step 4 Fill in the size portion of the part number. Choose the optimal size of the part based on the limitations of the cross-section and diameter (Page 8-9) and place into the part number as shown: Choice: 1.500" shaft x 2.000" bore x 0.500" bore depth Calculate Radial Cross-Section and input into part number: (2.000" Bore 1.500" Shaft) / 2 = 0.250" 0502LEN250XXXXXXXXVS Input shaft diameter into part number: 0502LEN25001500XXXVS Find minimum seal width from Page 8-9 and input into part number. Minimum seal width is always the most economical, but you can choose any width between the minimum recommended seal width and the actual bore depth. In this case you could choose any width between 0.250" and 0.500". Minimum seal width = 0.250" 0502LEN25002000250VS
32 30 0.063
Bore Depth R 0.025 Max.
Shaft .002 Bore +.004 - .000
Radius
15 0.25
Radial Cross-Section *Note: For more specific information on surface finish refer to Table 2-6 on Page 2-9.
From Part Number to Gland Dimensions

Step 1 Extract shaft dimensions from part number:
0502LEN37502125736VS
02125 = 2.125" shaft diameter For 2.125" shaft tolerance = .002" from drawing above. Step 2 Extract bore diameter from part number:
0502LEN37502125736VS
375 = 0.375" cross-section bore = shaft + (2 x cross-section) bore = 2.125" + (2 x 0.375) = 2.875" For 2.875" bore, tolerance = +.004/-.000 from drawing above. Step 3 Extract bore depth from part number:
0502LEN37502125736VS
736 = 0.736" seal height min. bore depth = seal height + 0.010" min. bore depth = 0.736" + 0.010" = 0.746"
01/15/06
8-3
www.parkerseals.com
Engineering
Table 8-2. Part Number Examples
0204LEN43703624375EN 0301LDE50105550525VS M127LGN09106620140SS M615LFE12516000200NN Profile LEN-N LDE-S LGN-S LFE-N Shaft Dia. 2.750 .002" 4.548 .002" 48.0 .08 mm 135.0 .0 8 mm Bore Dia. 3.624 + .004/-.000" 5.550 + .004/-.000" 66.2 + .16/-0 mm 160.0 + .16/-0 mm
Min. Bore Depth 0.385" 0.535" 14.25 mm 20.25 mm
O-ring Material EPDM Fluorocarbon Silicone Nitrile
FlexiLip Installation
Proper installation tools and techniques must be used to install the seal without damaging the critical sealing areas.
FlexiLip LFE (Mandrel Formed at Factory)
Sealing Diameter Installation Tool
Preform sealing lips by pushing seal completely over install tool. Refer to lip direction in the above illustration.
Lightly lube housing with system compatible lubricant. Place seal onto the end of the install tool. Slide install tool over end of shaft and onto sealing diameter.
Push seal over install tool and onto shaft. Remove install tool. IMPORTANT: Do not let seal dwell on installation tool.
Press seal into bore. Ensure that seal is square in the bore.
Figure 8-1. FlexiLip Installation
01/15/06
8-4
www.parkerseals.com

FlexiLip Installation Tool
1.50" Radius (Blended)
Engineering
0.020 Max.
80 85
16
Max. Shaft +.002 in.
Shaft .30
R 0.020 Max.
Figure 8-2. Installation Tool Dimensions
Hardware Notes
Each FlexiLip profile is given a standard pressure rating in Table 8-3 to aid the user in the selection of the most appropriate profile for an application. These pressure ratings are based on the assumptions that there is a large extrusion gap as shown in the first illustration and that the temperature at the gap is less than 300 F. Tightening the extrusion gap to around 0.015" on non-excluder lip profiles can double or triple the pressure rating for the seal. The extrusion gap for profiles with excluder lips must be at least 0.062" to allow the excluder lip to extend beyond the outside of the seal envelope if necessary. Reducing the extrusion gap does not improve the pressure rating of a seal with an excluder lip.
0.062 Min. Extrusion Gap
Fluid Pressure
Dust/ Dirt
Excluder Lip
0.015 Max. Extrusion Gap
Fluid Pressure
01/15/06
8-5
www.parkerseals.com
FlexiLip Rotary Seals Materials

The most popular fillers for FlexiLip products are graphite, fiberglass/ molybdenum disulfide, carbon fiber and mineral. 0301 Graphite Filled
Since graphite is often used as a lubricant, it does not significantly increase the coefficient of friction of PTFE when used as a filler. The low friction allows the compound to be used when both shaft speed and pressure are high. Graphite also is chemically inert which enables its use in corrosive medias. 0615 Proprietary Low Wear PTFE This proprietary filled PTFE offers low wear and friction properties, used in general applications where long life is required. Not recommended for applications with abrasive media.
A complete listing of material properties and limitations appears on Page 3-4. Feel free to contact the EPS division PTFE Engineering Team at (801) 972-3000 for more guidance on material selection.
0204 Molybdenum Disulfide and Fiberglass Filled Molybdenum disulfide increases the hardness of the seal surface while decreasing friction. It is normally used in small proportions combined with other fillers such as glass. MoS2 is also inert towards most chemicals. 0512 Carbon Fiber Filled Carbon fiber lowers creep, increases flex and compressive modulus and raises hardness. Coefficient of thermal expansion is lowered and thermal conductivity is higher for compounds of carbon fiber filled PTFE. Ideal for automotive applications in shock absorbers and water pumps. 0127 Mineral Filled Mineral is ideal for high temperatures and offers low abrasion to soft surfaces. PTFE with this filler can easily be qualified to FDA and other food-grade specifications.
01/15/07
8-6
www.parkerseals.com
FlexiLip Rotary Seals Product Offering

Decision Trees
The key application considerations that help in the selection of the right FlexiLip profile are operating temperature, media abrasiveness, pressure, external contamination, friction requirements, shaft diameter and Total Indicator Runout (TIR). Total Indicator Runout (TIR) is how far the shaft is misaligned with the bore during rotation. This is fully characterized in the general engineering section on Page 2-19. Only one FlexiLip profile is able to handle continuous service with runout conditions up to 0.020"; the LGN-N (or the LGN-S with the steel band). Keep in mind that the faster a shaft spins, the less TIR the seal can withstand. If the temperatures are extreme or if the shaft is over 4 inches in diameter, Parker recommends using a profile with a stainless steel band inserted into the side for dimensional stability during thermal cycling. This standard design can be called out by switching the -N for a -S in the profile code (and the part number). These decision trees are to be used as an engineering guide only. Often several other parameters must be considered to optimize seal design. Contact Parkers PTFE Engineering Team for confirmation of your choice or further recommendations. Parker also recommends that any seal be tested in the application conditions before releasing for production.
Use Banded Profile Follow the decision tree as normal, but substitute an -S instead of -N in the resulting profile code, indicating the same design with a steel band insert.
Temperature: <0 or >250 F or Shaft: > 4"?
LDE-N
Yes No
Need to exclude contaminates?
Yes No
Pressure in psi?
< 150 < 60
LDN-N
LEE-N Need to exclude contaminates?
Yes No
Abrasive Media?
LEN-N
Yes No
LFE-N Low speed and high runout? No

Yes
Need to exclude contaminates?
8
Yes No
LMN-N
Low Friction? Higher Friction/ Better Sealability?
LFN-N
LGN-N
01/15/06
8-7
www.parkerseals.com

Standard Profile
LFN-N LFN-S
Banded Profile*
Features
Formed Primary Lip
Multipurpose Seal
LFE-N
LFE-S
Multipurpose Seal
LMN-N
LMN-S
Low Friction
LEN-N
LEN-S
Elf-Toe Primary Lip
Abrasive Media
LEE-N
LEE-S
Abrasive Media
LDN-N
LDN-S
Dual Primary Lips
8
LDE-N LDE-S Dual Primary Lips w/ Excluder Lip Oil Seal Flooded, Severe Splash
LGN-N
LGN-S
0.020" > TIR > 0.005"
***Metal Banded 301 Stainless Steel. For use when temperature is <0 or >250 F or shaft diameter >4.000". ***Consult engineering for shaft diameters that are outside the range of our standards. ***Seals that are retained with an extrusion gap smaller than 0.020" will go to higher pressures than listed. Consult EPS Division Engineering. 01/15/06
8-8
www.parkerseals.com
Product Offering
Shaft Diameter**
0.625 to 12"
Cross-Section (Min.)
Standard 0.250" Banded 0.312"
Height (Min.)
Pressure (Max.)***
60 psi
Surface Speed (Max.)

5000 sfpm
Friction Rating (1 5 with 1 Best)

2
0.750 to 12"
60 psi
5000 sfpm
0.750 to 12"
30 psi
6000 sfpm
0.750 to 12"
60 psi
5000 sfpm
0.750 to 12"
60 psi
5000 sfpm
0.750 to 12"
150 psi
5000 sfpm
8
0.750 to 12" Standard 0.250" Banded 0.437" Standard 0.437" Banded 0.437" 150 psi 5000 sfpm 5
0.750 to 12"
60 psi
2000 sfpm
01/15/06
8-9
www.parkerseals.com
Notes
8-10
www.parkerseals.com
FlexiCase Rotary Seals Introduction

Contents
Engineering . . . . . . . . . . . . . . . . . Materials . . . . . . . . . . . . . . . . . . . Product Offering . . . . . . . . . . . . . 9-3 9-6 9-7
What Is a FlexiCase and How Does It Work?
The Parker FlexiCase is a rotary lip seal that features an ID lip that seals dynamically on a shaft and metal casing on its OD to seal statically press-fit into a bore. A gasket is sandwiched between layers of sealing lips and the can to seal off the potential leak path. Since the lip is not springenergized, the radial lip contact forces are lower than a rotary FlexiSeal, which allows the seal to function at much higher surface speeds (up to 10,000 sfpm).
FlexiCase
FlexiSeal Application
The seals are manufactured from a wide variety of PTFE composites and other machinable plastic materials. Standard gasket choices are fluorocarbon, nitrile, EPDM and Armstrong reinforced paper. Users can choose between stainless steel, cold-rolled steel, zinc plated cold-rolled steel and aluminum. This broad foundation of standard gasket, metal and PTFE materials can be tailored to suit nearly all applications. Standard and Nonstandard FlexiCase profiles are precision machined to fit inch and metric gland geometries. FlexiCase seals are used in demanding applications where the operating conditions exceed the capabilities of elastomeric seals.
Inner Case
Outer Gasket Case Excluder Lip
Spacer Washer
B/U Washer
Applications
The FlexiCases versatility makes it suitable for a wide range of applications including:
Motors Gear Boxes Pumps Bearings Compressors Cryogenics Extruders Valves Blowers Spindles Robotics Mixers
Garter Spring
Markets
Primary Lip Secondary Lip FlexiCase Components
FlexiCases low costs and high production capability make the FlexiCase an appealing choice for customers in a variety of markets including:
Aerospace Automotive Chemical Process Appliances Machine Tools Marine Medical Pharmaceutical Military Heavy Machinery Pulp & Paper Hydraulic Food Processing Electronic Oil & Gas Steel Mill Plastics 01/15/06
9-1
www.parkerseals.com
Introduction Part Number Nomenclature FlexiCase

Table 9-1. FlexiCase Part Number Nomenclature
English 0 5 0 2 CF E 2 5 0 0 0 8 7 5 2 5 0 N S
Gland Cross-Section Examples: 250 = 0.250" 375 = 0.375" 750 = 0.750" Excluder Lip Designation E = Excluder Lip N = No Excluder Lip
Seal Height Designation 250 = 0.250" 375 = 0.375" 750 = 0.750" Shaft Diameter Examples: 00875 = 0.875" 02500 = 2.500" 11000 = 11.000" Internal Gasket Material Designation N = Nitrile (NBR) V = Fluorocarbon (FKM) E = EPDM A = Special Paper Metal Case Material Designation S = 304 Stainless Steel C = Cold Rolled Steel Z = Zinc Plated CRS A = Aluminum
Metric M 5 0 2 CF E 1 4 0 0 1 2 0 0 0 2 0 0 N S
Gland Cross-Section Examples: 0900 = 9.00 mm 1250 = 12.50 mm 1400 = 14.00 mm Excluder Lip Designation E = Excluder Lip N = No Excluder Lip
Seal Height Designation 090 = 9.0 mm 200 = 20.0 mm 384 = 38.4 mm Shaft Diameter Examples: 00705 = 7.05 mm 05050 = 50.50 mm 12000 = 120.00 mm Internal Gasket Material Designation N = Nitrile (NBR) V = Fluorocarbon (FKM) E = EPDM A = Special Paper
Metal Case Material Designation S = 304 Stainless Steel C = Cold Rolled Steel Z = Zinc Plated CRS A = Aluminum
CFN
CMN
CEN
CDN
CGN
CJN
CHN
CFE
CME
CEE
CDE
CGE
CJE
CHE 01/15/06
9-2
www.parkerseals.com
FlexiCase Rotary Seals Engineering

From Gland Dimensions to Part Number
Step 1 Choose profile. Choose the best profile for your application from the decision tree and table on Pages 9-7 through 9-9, and place the 3-character profile description into the part number as shown here in this example. Choice: CFE profile XXXXCFEXXXXXXXXXXXXX Step 2 Choose material. Choose the best material for the application and place the 4-digit material code into the part number as shown here: Choice: 0301 Graphite Filled PTFE 0301CFEXXXXXXXXXXXXX Step 3 Choose gasket material. Choose the best gasket material after considering the chemicals and temperatures it will be exposed to. Consult the Parker O-Ring Handbook (ORD 5700A/US Section II) as a general reference and choose the most appropriate material family. Place in the part number as shown here: Choice: Nitrile gasket (N code) 0301CFEXXXXXXXXXXXNX Step 4 Choose metal can material. Consult Page 9-6 and choose the best fit for the application. Place the choices in the part number as shown here: Choice: Cold rolled steel can (C code) 0301CFEXXXXXXXXXXXNC Step 5 Fill in the size portion of the part number. Choose the optimal size of the part based on the limitations of the cross-section and diameter (Pages 9-8 to 9-9) and place into the part number as shown: Choice: 2.250" shaft x 3.125 .0015 bore x 0.500" bore depth Calculate Radial Gland Cross-Section and input into part number: (3.125" Bore 2.250" Shaft) 2 = 0.4375", rounds to 0.438" 0301CFE438XXXXXXXXNC Input shaft diameter into part number: 0301CFE43802250XXXNC
32 30 0.063
Bore Depth R 0.025 Max.
Shaft .002 Bore Radius
15 0.25 Radial Cross-Section *Note: For more specific information on surface finish refer to Table 2-6 on Page 2-9.
Step 6 Find minimum seal width from Pages 9-8 to 9-9 and input into part number. Minimum seal width is always the most economical, but you can choose any width between the minimum recommended seal width and the actual bore depth. In this case you could choose any width between 0.200" and 0.500". Minimum seal width = 0.200" 0301CFE43802250200NC
From Part Number to Gland Dimensions

Step 1 Extract shaft dimensions from part number: 0301CGN50001125437VS 01125 = 1.125" shaft diameter Apply tolerance according to Table 9-2 For 1.125" shaft tolerance = .003" plunge grind shaft to achieve low surface finish Step 2 Extract bore diameter from part number:
0301CGN50001125437VS
500 = 0.500" cross-section Bore = Shaft + (2 x cross-section) Bore = 1.125" + (2 x .500) = 2.125" Apply tolerance according to Table 9-2 For 2.125" bore, tolerance = .001" Step 3 Extract bore depth from part number:
0301CGN50001125437VS
437 = 0.437" seal height min. bore depth = seal height min. bore depth = 0.437"
01/15/06
9-3
www.parkerseals.com
Engineering
Table 9-2. Bore Tolerance
Bore Up to 3" 3.001 to 6" 6.001 to 8" 8.001 to 9" 9.001 to 10" Bore Tolerance .001" .0015" .002" .002" .002" Max. Housing Radius 0.045" 0.054" 0.072" 0.090" 0.125" Metric Bore Up to 75 mm 75.01 to 150 mm 150.01 to 200 mm 200.01 to 230 mm 230.01 to 254 mm
Bore Tolerance .025" .038" .050" .050" .050"
Max. Housing Radius 1.14 mm 1.37 mm 1.83 mm 2.29 mm 3.18 mm
Table 9-3. Part Number Examples

Profile 0204CEN43702750375VCN 0301CJE50104548525NSP M127CDN091004800140NSZ M615CFE125013500200EAG CEN CJE CDN CFE Shaft 2.750 .002" 4.548 .002" 48.0 .08 mm 135.0 .08 mm Bore 3.624 .0015" 5.550 .0015" 66.2 .025 mm 160.0 .050 mm Min. Bore Depth 0.385" 0.535" 14.25 mm 20.25 mm Gasket Material FKM Nitrile Nitrile EPDM
FlexiCase Installation
Proper installation tools and techniques must be used to install the seal without damaging the critical sealing areas.
FlexiCase CFE (Mandrel Formed at Factory)
Sealing Diameter Installation Tool
Preform sealing lips by pushing seal completely over install tool.
Place seal onto the end of the install tool. Slide install tool over end of shaft and onto sealing diameter.
Push seal over install tool and onto shaft. Remove install tool. IMPORTANT: Do not let seal dwell on installation tool.
Press seal into bore. Ensure that seal is square in the
Figure 9-1. FlexiCase Installation

01/15/06
9-4
www.parkerseals.com

FlexiCase Installation Tool
1.50" Radius (Blended)
Engineering
0.020 Max.
80 85
16
Max. Shaft +.002 in.
Shaft .30
R 0.020 Max.
Figure 9-2. Installation Tool Dimensions
01/15/06
9-5
www.parkerseals.com
FlexiCase Rotary Seals Materials

The most popular fillers for FlexiCase products are graphite, fiberglass/molybdenum disulfide, carbon fiber and mineral. 0502 Carbon Fiber Filled
Carbon fiber lowers creep, increases flex and compressive modulus and raises hardness. Coefficient of thermal expansion is lowered and thermal conductivity is higher for compounds of carbon fiber filled PTFE. Ideal for automotive applications in shock absorbers and water pumps. 0127 Mineral Filled Mineral is ideal for improved upper temperatures and offers low abrasion to soft surfaces. PTFE with this filler can easily be qualified to FDA and other food-grade specifications.
A complete listing of material properties and limitations appears on Page 3-4. Feel free to contact the EPS division PTFE Engineering Team at (801) 972-3000 for more guidance on material selection. 0301 Graphite Filled Since graphite is often used as a lubricant, it does not significantly increase the coefficient of friction of PTFE when used as a filler. The low friction allows the compound to be used when both shaft speed and pressure are high. Graphite also is chemically inert which enables its use in corrosive medias. 0615 Proprietary Low Wear PTFE
Metal Can Materials

S Stainless Steel Good chemical resistance properties up to 600 F. Resists corrosive media up to 400 F. C Cold-Rolled Steel Good in oils and other media friendly to ferrous metals up to 600 F. Excellent value for costsensitive projects. Z Zinc-Plated Cold-Rolled Steel
This proprietary filled PTFE offers low wear and friction properties, used in general applications where long life is required. Not recommended for applications with abrasive media. 0204 Molybdenum Disulfide and Fiberglass Filled Molybdenum disulfide increases the hardness of the seal surface while decreasing friction. It is normally used in small proportions combined with other fillers such as glass. MoS2 is inert towards most chemicals.
Good in oils and mildly corrosive media up to 450 F. A lower cost alternative to stainless steel. A Aluminum Excellent lightweight, high-strength material. Should be used with aluminum housing when thermal cycling is likely.
01/15/07
9-6
www.parkerseals.com
FlexiCase Rotary Seals Product Offering

Decision Tree
The key application considerations that help in the selection of the right FlexiCase profile are operating temperature, media abrasiveness, pressure, external contamination, friction requirements, shaft diameter and Total Indicator Runout (TIR). Also see Table 9-4 for more information on temperatures, pressures, speeds and friction. Total Indicator Runout (TIR) is how far the shaft is misaligned with the bore during rotation. This is fully characterized in the general engineering section on Page 2-19. Four FlexiCase profiles are able to handle continuous service with runout conditions up to 0.010" if speeds are slower than 200 RPM; the CGN, CGE, CJN and CJE. Keep in mind that the faster a shaft spins, the less TIR the seal can withstand. These decision trees are to be used as an engineering guide only. Often several other parameters must be considered to optimize seal design. Contact Parkers PTFE Engineering Team for confirmation of your choice or further recommendations. Parker also recommends that any seal be tested in the application conditions before releasing for production.
CME Need to exclude contaminants?

Yes No
CMN
CEE Need to exclude contaminants?

Yes No
Abrasive Media? Low speed & high runout?
Yes No
CEN
CFE
No Yes Yes No Need to exclude contaminants?
CFN
< 35 CGE Operating Pressure in psi 35 to 75 75 to 500 Need to exclude contaminants?

Yes No
CGN
500 to 750 Need to exclude contaminants?

Yes No
CDE
CDN
No
Low speed & high runout?
Yes
CJE
Yes
Need to exclude contaminants?
No
CJN
CHE Need to exclude contaminants?

Yes No
CHN
01/15/06
9-7
www.parkerseals.com

Profile CFN Features Formed Primary Lip Recommended Applications General purpose rotary shaft seal. Shaft Diameter Limits CrossSection Limits Height Limits* 0.175"
Pressure Limit at Room Temp. 250 psi
Surface Speed Max. 5000 sfpm
Friction Rating 2
0.125" to 6" Min 0.250" Max 2"
CFE
Ideal to keep oil in and water & dirt out.
0.250" to 6" Min 0.250" Max 2"
0.200"
125 psi
5000 sfpm
CMN
General purpose rotary shaft seal w/ low breakaway torque.
0.250" to 6" Min 0.250" Max 2"
0.175"
125 psi
6000 sfpm
CME
Machined Primary Lip w/ Excluder Lip
Ideal to keep oil in and water & dirt out. Low Breakaway torque.
0.250" to 6" Min 0.250" Max 2"
0.200"
125 psi
6000 sfpm
CEN
Elf-Toe Primary Lip
General purpose rotary 0.125" to 6" Min 0.250" shaft seal where shaft Max 2" runout is 0.005" to 0.010" or abrasive media.
0.175"
250 psi
5000 sfpm
CEE
Ideal to keep oil in and water & dirt out where shaft runout is 0.005" to 0.010" or abrasive media.
0.250" to 6" Min 0.250" Max 2"
0.200"
125 psi
5000 sfpm
CDN
Dual Redundant sealing for Primary Lips aircraft or other low leakage systems.
0.250" to 6" Min 0.250" Max 2"
0.500"
250 psi
5000 sfpm
CDE
Redundant sealing for 0.250" to 6" Min 0.250" aircraft or other low Max 2" leakage systems. Keeps water & dirt out.
0.500"
250 psi
5000 sfpm
* Minimum height requirements can be reduced significantly if pressures are low and diameters are small. Consult PTFE Engineering for recommendations. 01/15/06
9-8
www.parkerseals.com

Profile CGN Features Primary Lip Energized with Garter Spring Recommended Applications Shaft Diameter Limits CrossSection Limits Height Limits* 0.200" Pressure Limit at Room Temp. 125 psi
Product Offering
Surface Speed Max. 2000 sfpm
Friction Rating 3
Use when shaft runout 0.250" to 6" Min 0.250" is 0.010" to 0.020" or Max 2" abrasive media.
CGE
Primary Lip Energized with Garter Spring w/ Excluder Lip
Use when shaft runout 0.250" to 6" Min 0.250" is 0.010" to 0.020" or Max 2" abrasive media. Keeps water & dirt out.
0.200"
125 psi
2000 sfpm
CJN
Dual Lip Seal w/ Primary Lip Energized with Garter Spring Dual Lip Seal w/ Primary Lip Energized with Garter Spring w/ Excluder Lip High Pressure Dual-Lip Seal with Metal Backup Washer High Pressure Dual-Lip Seal with Metal Backup Washer w/ Excluder Lip
Use when redundant sealing is needed & shaft runout is 0.010" to 0.020" or abrasive media.
0.250" to 6" Min 0.250" Max 2"
0.500"
125 psi
2000 sfpm
CJE
Use when redundant sealing is needed & shaft runout is 0.010" to 0.020" or abrasive media. Keeps water & dirt out. Redundant seal for high pressure aircraft or other low leakage systems.
0.250" to 6" Min 0.250" Max 2"
0.500"
125 psi
2000 sfpm
CHN
0.250" to 6" Min 0.250" Max 2"
0.500"
500 psi
2000 sfpm
CHE
Redundant seal for high pressure aircraft or other low leakage systems. Keeps water & dirt out.
0.250" to 6" Min 0.250" Max 2"
0.500"
500 psi
2000 sfpm
* Minimum height requirements can be reduced significantly if pressures are low and diameters are small. Consult PTFE Engineering for recommendations.
01/15/06
9-9
www.parkerseals.com
Notes
9-10
www.parkerseals.com
NEED HELP? If you need assistance, please photocopy these three pages. Fill out the required information and fax to (801) 973-4019. Use the information below and other information in this catalog to determine the dimensions needed. We will contact you to discuss your specific application and make recommendations. If you need help filling out this form, please call Applications Engineering at (801) 972-3000. ENGINEERED POLYMER SYSTEMS DIVISION DESIGN ACTION REQUEST
EPS Division 2220 South 3600 West Salt Lake City, UT Tel: (801) 972-3000 Fax: (801) 973-4019 Referred by _________________ Lead # _____________________ Applications Engineering Use: Project # ____________________________ Date Entered ________________________ Date Required _______________________ Prepared by _________________________ Territory Mgr. ________________________ Distributor ___________________________ Distributor ___________________________ Dist. Sales __________________________
COMPANY: ___________________________________________ ADDRESS: ___________________________________________ CITY: _________________________ CONTACT: ____________________ ALT. CONTACT: ________________ STATE: ______________ TITLE: _______________ TITLE: _______________
FAX NUMBER:_________________________________________ P.O. BOX:______________________ ZIP:___________________________ PHONE: _______________________ PHONE: _______________________ MAIL STOP: __________ COUNTRY: ___________ EXT:_________________ EXT:_________________
E-MAIL: ______________________________________________
EQUIPMENT/MANUFACTURER: _________________________________________________________ EXISTING SEAL MANUFACTURER: ______________________________________________________ REASON FOR CHANGE: PERFORMANCE DELIVERY NEW APPLICATION
MODEL NO.: _____________ PART NO.: ______________ PRICE
CURRENT PRICE: ________ @ _____ PCS. MONTHLY USAGE: _____ TARGET PRICE: ________ @ _____ PCS. SPECIAL INSPECTION REQUIREMENTS: QUOTE QTY.: _____ YES NO
HOURS OPERATION: _____ HOURS SERV. LIFE: _____ PROTO QTY.: _____ DATE PROTO REQD.: _____ YES NO
SPECIAL PACKAGING REQUIREMENTS:
EXPLAIN: _____________________________________________________________________________________________________
MOTION STATIC RECIPROCATING OSCILLATORY ROTARY
PRODUCT TYPE NON-ROTARY FILL OUT SECOND PAGE ROD/SHAFT PISTON INTERNAL FACE EXTERNAL FACE WIPER BEARING VANE NON-SEAL 01/15/06 ROTARY FILL OUT THIRD PAGE SOLID SEAL SPLIT SEAL BEARING ISOLATOR PTFE LIP SEAL ELASTOMER LIP SEAL
A-1
www.parkerseals.com
A
OPERATING PARAMETERS TEMPERATURE: PRESSURE: STROKE LENGTH (RECIPROCATING): CYCLE RATE: DEGREE OF ARC (OSCILLATING): VELOCITY: VACUUM: UNIT (CIRCLE ONE) K F C PSI BAR MPA INCH MM /MIN. /HR. HZ DEGREES FT/MIN. MM/MIN. IN HG TORR MINIMUM ____________ ____________ ____________ ____________ ____________ ____________ ____________ OPERATING ____________ ____________ ____________ ____________ ____________ ____________ ____________ MAXIMUM ____________ ____________ ____________ ____________ ____________ ____________ ____________
MEDIA TO BE SEALED: __________________________________
Rod
D E
Piston
E D
Face Seal
B A D
C B A
B C
Other Piston
E D
Other Rod
D F E
F A B C A B C
HARDWARE SPECIFICATIONS A DIAMETER: B DIAMETER: C DIAMETER: D GROOVE WIDTH: E RADIAL CLEARANCE: F ROD / PISTON STEP HEIGHT: SIDE LOAD (LBS. NEWTONS): MIL-G-5514 O-RING DASH #: AS4716 O-RING DASH #: GLAND TYPE ____ SPLIT ____ OPEN ____ SOLID ____ STEPPED
HARDWARE DRAWINGS INCLUDED WITH DAR: YES NO MIN. ________ MAX. ________ HARDNESS ________ FINISH ________ MATL ________ MIN. ________ MAX. ________ HARDNESS ________ FINISH ________ MATL ________ MIN. ________ MAX. ________ HARDNESS ________ FINISH ________ MATL ________ MIN. ________ MAX. ________ CAN HARDWARE BE CHANGED? YES NO MIN. ________ MAX. ________ HOW? ________________________________________________ MIN. ________ MAX. ________ _______ PERFORMANCE REQUIREMENTS ______ BACK-UP WIDTH ____ (CIRCLE ONE) ______ BACK-UP WIDTH ____ FRICTION: LBS OZ GMS BREAKOUT ____ DYNAMIC ____ EXPECTED LIFE: CYC HRS YRS _______________________ METRIC MAX. LEAKAGE: DROPS CC/MIN _________________________ YES MOST CRITICAL ASPECT: _______________________________ NO CONTAMINATION: ______________________________________
01/15/06
A-2
www.parkerseals.com

ROTARY SEALS
SHAFT MOVEMENT CLOCKWISE COUNTERCLOCKWISE BIDIRECTIONAL OSCILLATING MEDIA TO SEAL IN: ____________________________________ MEDIA TO SEAL OUT: __________________________________ SHAFT POSITION HORIZONTAL VERTICAL UP VERTICAL DOWN LUBRICATION METHOD OIL SPLASH, OIL LEVEL BELOW SHAFT OIL FLOODED, OIL LEVEL ABOVE SHAFT GREASE W/O PURGE GREASE WITH PURGE OIL MIST
ALLOWABLE LEAKAGE: ______________________________
OPERATING PARAMETERS TEMPERATURE: PRESSURE:
UNIT (CIRCLE ONE) K PSI F BAR Nm C MPA
MINIMUM ____________ ____________ ____________
OPERATING ____________ ____________ ____________
MAXIMUM ____________ ____________ ____________
FRICTIONAL TORQUE REQUIREMENTS: in-lb.
DIMENSIONS LISTED ARE: SHAFT AXIAL:_______ ______ A SHAFT:___________ ______ C BORE: ___________ ______ D BORE: ___________ ______ SHAFT (RPM):_______________
INCH
METRIC
SHAFT TO BORE: ______________ B SHAFT:_____________________ E DISTANCE TO FIRST: _________ F DIST. FROM HSG.: ___________ SHAFT FINISH (Ra): ____________
Distance from step to housing
30
CHb Radius CHa C Housing Diameter 15
SHAFT MATERIAL: _____________________________________________ BORE (RA): _________________ BORE MATERIAL:______________
RUNOUT (TIR): ________________________________________________ ECCENTRICITY: _______________________________________________
E Distance to 1st Obstruction (keyway or coupling or step on shaft)

SNAP RING GROOVE O-RING GROOVE
SHAFT FEATURES: KEYWAY SPLINE
D Cavity Width
FDA MATERIAL REQUIRED
SEAL NEEDS TO EXCLUDE HIGH PRESSURE WATER SPRAY
SEAL INSTALLATION DATA INSTALLATION DIRECTION: LIP FACES TOWARDS BEARING LIP FACES AWAY FROM BEARING
SEAL INSTALLED BY:
PUSHING SEAL OVER SHAFT
PUSHING SHAFT THROUGH SEAL SHAFT DIRECTION IS SAME AS LIP DIRECTION
IF SHAFT IS PUSHED THROUGH SEAL:
SHAFT DIRECTION OPPOSES LIP DIRECTION
01/15/06
A-3
www.parkerseals.com
A
Notes
A-4
www.parkerseals.com
Problem Solved Case Studies

This section is filled with real-world applications for which Parker has designed a successful solution. The following solutions illustrate the wide capability of PTFE sealing in various applications.
FlexiSeal Applications
Robotic Arm Wafer Press
Motion: Rotation: Speed: Pressure: Temperature: Media: Life: Breakaway Friction: Allowable Leakage: Dynamic Surface: Static Surface: Spring Material: Jacket Material: Oscillatory 60 16 sfpm 0.5 Torr 14.5 psi 68 to 77 F Vacuum/Atmosphere 2,500,000 cycles 2 in/oz max. (Repeatable) Zero 4 Ra Electrolysis Nickel/Aluminum 70 Rc 16 Ra Electrolysis Nickel/Aluminum 70 Rc 301 Stainless Steel (Cantilever) Ekonol Filled PTFE (Aromatic Polyester Filled PTFE)
01/15/06
B-1
www.parkerseals.com
Problem Solved Case Studies FlexiSeal Applications (Continued)

Plasma Generator
Motion: Stroke: Frequency: Pressure: Temperature: Media: Life: Breakaway Friction: Allowable Leakage: Dynamic Surface: Static Surface: Spring Material: Jacket Material:
Reciprocating (Rod) 0.040 0.080" 90 cycles/hr. 20 MTorr 14.7 psi 70 to 150 F Vacuum/Atmosphere 750,000 Cycles Repeatable Zero 4 Ra Sapphire or Quartz Tube 16 Ra Aluminum 301 Stainless Steel (Cantilever) UHMWPE
UHMWPE FlexiSeal for this semiconductor application is best suited for the cleanliness demands and vacuum requirements.
Spiked Flange Male Flanged Seal Female
Liquid Oxygen Quick Disconnect

Motion: Stroke: Frequency: Pressure: Temperature: Media: Dynamic Friction: Allowable Leakage: Spring Material: Jacket Material: Reciprocating (Rod) 0.500" 1 50 cycles/day 0 60 psi -320 to +120 F Liquid Oxygen 5 lbs. Force max. Zero 301 Stainless Steel (Cantilever) Virgin PTFE
Media Poppet Poppet
Quick Coupling to transfer and refill LOX home and portable units. Flanged spiked for sealability and to prevent seal shrinkage during thermal cycling.
01/15/06
B-2
www.parkerseals.com

Biomedical Liquid Handling Systems
Motion: Stroke: Frequency: Pressure: Temperature: Media: Life: Breakaway Friction: Allowable Leakage: Dynamic Surface: Static Surface: Energizer Material: Jacket Material: Reciprocating (Rod) 0 0.500" 60 Hz Vacuum 50 to 100 F Dimethyl Sulfoxide 500,000 Cycles Repeatable Zero 4 Ra 303 Stainless Steel (Plunger) 20 Rc Chem Film (Yellow) Aluminum Fluorocarbon Virgin PTFE
Liquid Dispensing Cylinder

Motion: Stroke: Frequency: Pressure: Temperature: Media: Life: Allowable Leakage: Dynamic Surface: Static Surface: Energizer Material: Jacket Material: Reciprocating (Rod) 2.000 4.000" 1 4 cycles/min. 200 3000 psi -60 to +180 F Epoxy, Adhesives and Catalysts 1,000,000 Cycles Zero 8 16 Ra Steel (Chrome) 60 65 Rc 32 Ra Aluminum EPDM UHMWPE
01/15/06
B-3
www.parkerseals.com

High Pressure Washers Axial Pump
Motion: Stroke: Frequency: Speed: Pressure: Temperature: Media: Life: Allowable Leakage: Dynamic Surface: Static Surface: Jacket Material: O-Ring Material:
Reciprocating (Rod) 0.250" 3,450 cycles/min. 1,725 sfpm 0 3,000 psi 35 to 160 F Water 2,000 8,000 Hrs. 2 drops/Hr. 6 10 Ra (55 60 Rc) 440C Stainless Steel 120 Ra Brass Carbon Fiber Filled PTFE Nitrile
A commercial power washer manufacturer was seeking high pressure seal which would meet 8000 hour requirement. Elastomer energized FlexiSeal provided a best-value solution. Carbon fiber-filled provided the life requirement in this non-lubricated environment.
Gas Turbine Gear Box and Bearing Compartment Static Seals

Motion: Pressure: Temperature: Media: Static Face Seal 'P = -30 to 200 psi 65 to 400 F MIL-L-23699, MIL-L-7808 or Oil/Air Mixture Life: 5,000 Hrs. Allowable Leakage: Zero Static Surface: 32 Ra Titanium and 63 Ra Nickel Alloy Jacket Material: Virgin PTFE Spring Material: Tempered Elgiloy (Helical) Aerospace engine manufacturers utilize high temperature FlexiSeals where standard O-ring compounds fail to meet the required temperature ranges and life requirements. Excellent compatibility is achieved with use of virgin PTFE.
01/15/06
B-4
www.parkerseals.com

Tank Cleaners
Motion: RPM: Pressure: Temperature: Media: Rotates on ID and OD 20 40 50 1000 psi 32 to 220 F Water/Detergents, Solvents, Abrasive Compounds Speed: 2.7 sfpm Allowable Leakage: Zero Dynamic Surface: 16 Ra 17 4PH HT (Shaft) 45 Rc 32 Ra 316 Stainless Steel (Bore) 28 Rc Static Surface: 32 Ra 316 Stainless Steel Spring Material: Elgiloy (Cantilever) Jacket Material: PPS/Carbon Fiber Filled PTFE Bearing Material: Carbon Fiber Filled PPS
Carpet Steam Cleaner Pump

Motion: RPM: Speed: Pressure: Temperature: Media: Friction: Life: Allowable Leakage: Dynamic Surface: Static Surface: Jacket Material: O-Ring Material: Rotary Shaft 13,000 425 sfpm 20" Hg Vacuum to 10 psi 70 to 100 F Exposure to Cleaning Solutions Low (Continuous Dry Run) 300 500 Hrs. Zero (Air) 10 30 Ra 303 Stainless Steel (Shaft) 20 Rc 32 Ra Plastic Housing Carbon Fiber Filled PTFE Nitrile
01/15/06
B-5
www.parkerseals.com
Problem Solved Case Studies FlexiLip Applications

Air Conditioning Compressors
Motion: Rotation: RPM: Pressure: Temperature: Media:
Rotary Shaft CW 1725 1850 20 300 psi 32 to 325 F R12, R22, R500, R502, R134, R404A, R410A Speed: 260 sfpm Life: 15,000 Hrs. Allowable Leakage: Zero Seal Material: Pigmented Virgin PTFE The LDN FlexiLip profile is often selected for use as a compressor shaft seal. The seal material meets compatibility testing with all refrigerants in conjunction with high-speed, long life application requirements. Meets EPA zero leakage requirements.
Transportation Supercharger
Motion: RPM: Pressure: Temperature: Media: Rotary Shaft 14,000 max. 19 25 in vacuum, 10 12 psi boost 220 F Sealed In Synthetic Oil, GL5, 75W Sealed Out Atmosphere Velocity: 3100 sfpm Allowable Leakage: None Dynamic Surface: Case Hardened Steel, 16 Ra 60 Rc Static Surface: Cast Aluminum, 32 Ra Seal Materials: Glass/Moly Filled PTFE with Fluorocarbon O-Ring
01/15/06
B-6
www.parkerseals.com
Problem Solved Case Studies FlexiLip Applications (Continued)

Transportation Universal Joint
Motion: RPM: Temperature: Media: Rotary Oscillating 250 500 Ambient Sealed In Grease Sealed Out Dust Velocity: 150 300 sfpm Allowable Leakage: None Dynamic Surface: 4140, 10 20 Ra 50 Rc Static Surface: 4140, 10 20 Ra 50 Rc Seal Material: Graphite Filled PTFE with Fluorocarbon O-Ring
Industrial Gearbox
Motion: Rotation: RPM: Pressure: Temperature: Media: Rotary Shaft CW/CCW (Bi-directional) 200 1800 5 psi Ambient Sealed In Gear Oil Sealed Out Water Washdown Velocity: 110 1020 sfpm Allowable Leakage: None Dynamic Surface: 440 Stainless Steel, 10 20 Ra 15 Rc Static Surface: Cast Iron, 63 Ra Seal Materials: Proprietary Filled PTFE with Fluorocarbon O-Ring
01/15/06
B-7
www.parkerseals.com
Problem Solved Case Studies FlexiCase Applications

Stationary and Portable Air Compressors
Motion: Rotation: RPM: Speed: Pressure: Vacuum: Temperature: Media:
Rotary Shaft CW/CCW (Bi-directional) 1780 3600 1650 sfpm 30 175 psi 28 Hg -40 to +250 F Silicone/Polyglycol, Diester, Hydrocarbon SHC Lube Oils Life: 15,000 Hrs. Allowable Leakage: Zero Shaft Surface: 16 20 Ra Steel 30 36 Rc Seal Material: Carbon Fiber Filled PTFE Case Material: S.A.E. 1008/1020 CRS
Hydraulic Gear Pumps and Motors

Motion: Rotation: RPM: Pressure: Temperature: Media: Speed: Life: Allowable Leakage: Dynamic Surface: Static Surface: Seal Material: Case Material: Rotary Shaft CW/CCW (Bi-directional) 1750 3000 100 250 psi -30 to +250 F S.A.E. 10W Hydraulic Oil 612 spfm 500 1000 Hrs. 1 drop/Hr. 12 Ra Hardened Steel 58 62 Rc 32 Ra Cast Iron or Aluminum Carbon/Graphite Filled PTFE S.A.E. 1008/1020 CRS
A gear pump manufacturer looking for increasing longevity selected CHE profile FlexiCase featuring redundant sealing lips and wiper/scraper. Seal material provided increased wear resistance to achieve 1000 hour requirement.
01/15/06
B-8
www.parkerseals.com
Problem Solved Case Studies FlexiCase Applications (Continued)

Freon Recovery System Compressor
Motion: Rotation: RPM: Pressure: Temperature: Media: Rotary Shaft CW 1725 1850 20 300 psi 32 to 325 F R12, R22, R500, R502, R134, R404A, R410A Speed: 250 sfpm Life: 1,000 1,500 Hrs. Allowable Leakage: Zero Dynamic Surface: 8 Ra Tool Steel 58 62 Rc Static Surface: 16 Ra Aluminum Seal Material: Glass/Moly Filled PTFE Case Material: 304 Stainless Steel
Gas Turbine Engine Sump

Motion: RPM: Speed: PV: Pressure: Temperature: Media: Leakage: Dynamic Surface: Static Surface: Life: Seal Lip Material: Cases: Gasket: Rotary Shaft 8,000 8,700 14,300 15,500 sfpm 77,400 0 5 psi -65 to +250 F MIL-L-23699/MIL-L-7808/Hot Air Zero (Static) 20 Ra Chromium Carbide 60 70 Rc 125 Ra Type III Anodized Aluminum 10,000 Hrs. Carbon/Graphite Filled PTFE Inner/Outer Aluminum AMS 4016/4150 Fluorocarbon
01/15/06
B-9
www.parkerseals.com
Problem Solved Case Studies FlexiCase Applications (Continued)

Gas Turbine Scavenge Pump Line
Motion: RPM: Speed: Pressure: PV: Temperature: Media: Leakage: Dynamic Surface: Static Surface: Life: Seal Lip Material: Cases: Gasket:
Rotary Shaft 8,000 1,450 sfpm 45 psi 65,250 -65 to +425 F MIL-L-23699/MIL-L-7808/Hot Air Zero 16 Ra Type III Anodized Aluminum 60 70 Rc 10,000 Hrs. Carbon Fiber Filled PTFE, Uni-directional Hydro Lip Inner/Outer 304 Stainless Steel Fluorocarbon
01/15/06
B-10
www.parkerseals.com
Medias Acetaldehyde Acetamide Acetate solvent Acetic acid Acetic acid, 20% Acetic acid, 80% Acetic acid, Glacial Acetic anhydride Acetone Acetyl chloride (dry) Acetylene Acrylonitrile Adipic acid Alcohols: Amyl Benzyl Butyl Diacetone Ethyl Hexyl Isobutyl Isopropyl Methyl Octyl Propyl Aluminum chloride Aluminum chloride, 20% Aluminum fluoride Aluminum hydroxide Aluminum nitrate Alum. Potassium sulfate Aluminum sulfate Alums Amines Ammonia 10% Ammonia nitrate Ammonia, anhydrous Ammonia, liquid Ammonium acetate Ammonium bifluoride Ammonium carbonate Ammonium chloride Ammonium hydroxide Ammonium nitrate Ammonium persulfate Ammonium phosphate: Dibasic Mono-basic Tribasic Ammonium sulfate Amyl acetate Amyl chloride Aniline Aniline hydrochloride A2 A A A A A A A A2 A C A1 C1 D C D B1 B1 C1 D B B B B A A2 A D B B B B A A1 B D A A A A A A A A2 A2 A A A A A A A A A A A2 A A A A A A A A A A A1 B2 D A B1 B A A2 A2 A1 A A2 B2 B2 A2 A2 A2 A2 A2 A C1 C1 A B2 C1 A A2 B2 A2 A1 A1 A2 A A A B C B1 D A1 D A1 C B1 A A A A A A A B A A A B D D A1 A D B A A A A B2 B D B C A1 A1 A A A A A A A A A A C A A A B B C B B B A B B B B D B B B A A A A A A A A A A A B C C A A A A B C A A PTFE A A A A A A A A A A A A A UHMW PE C A A A2 A D D D B D D A A TPE A A B B A 301 SS A B A D B D C B A A A A1 A1 Hast C-276 A A A A A A A A A B Elgiloy A A A A A A A A A A Medias Antimony trichloride Aqua regia Arochlor 1248 Aromatic hydrocarbons Arsenic acid Asphalt Barium carbonate Barium chloride Barium cyanide Barium hydroxide Barium nitrate Barium sulfate Barium sulfide Benzaldehyde Benzene Benzenesulfonic acid Benzoic acid Benzol Boric acid Bromine Butadiene Butane Butyl Acetate Butylene Butyric acid Calcium bisulfide Calcium carbonate Calcium chloride Calcium hydroxide Calcium hypochlorite Calcium oxide Calcium sulfate Carbon bisulfide Carbon dioxide Carbon dioxide (Dry) Carbon dioxide (Wet) Carbon disulfide Carbon monoxide Carbon tetrachloride Carbonic acid Catsup Chlorinated glue Chlorine water Chlorine, anhydrous liquid Chlorine, dry Chlorobenzene (Mono) Chloroform Chlorosulfonic acid Chromic acid 5% Chromic acid 10% Chromic acid 30% Chromic acid 50% Cider Citric acid PTFE A A A A A1 A A A1 A A1 A A A1 A A A2 A A A A2 A A A A2 A A A A A A A A A A A A A A A A A B A1 A A A A A A UHMW PE B2 B1 C1 C B2 A1 B2 A1 B B2 B2 B2 B2 A1 C1 A1 A1 C1 A2 D D C1 C1 B1 D B1 B1 B2 A2 A1 B1 B1 A1 A1 A1 C1 A2 D B2 B1 D D C1 C1 D D D D D B D
TPE C1 C1 B1 B1 B1 D B C B D C A1 D B B1 B1 A1 B1 C1 A C1 A A1 A D D D D D D D D D D B1 A1
301 SS D D B A2 B B1 A1 A1 B B B B B B B B A1 B2 D A A2 B A B2 B A1 C2 B1 C1 A B A A A A A1 A B A1 A C C1 A1 A A D B B B2 C A B1
Hast C-276 C A B B B A B A A B B B1 B A A C A A A1 A B A A B A B A A A B B A1 A2 A2 D A2 A A1 A1 B A D B A
Elgiloy D C A C A C A A A A A A A A A A B B B C A A
A = No Effect/Excellent 1Maximum 72 F (22 C)
B = Minor Effect/Good C = Moderate Effect/Fair 2Maximum 120 F (48 C)
D = Severe Effect/Poor
01/15/06
C-1
www.parkerseals.com
Medias Clorox (bleach) Coffee Copper chloride Copper cyanide Copper fluoborate Copper nitrate Copper sulfate 5% Copper sulfate >5% Cream PTFE A A A A A A A A A A A A A1 A A D A2 D A1 A A A A1 A A A A A A A A A A A A A A A A A D A A A A A A A A A A A B A A B UHMW PE B2 B2 A2 A2 C1 B1 B1 D D A C1 C1 D B2 A A2 B D D C2 C1 D D D A D D A D A1 A2 A2 A2 A2 D A2 A2 D B D C A1 A B D D A TPE A1 A1 A1 D A1 C B C C A A C B B A A A A 301 SS A A D B D A B B A A2 A1 A1 A1 A1 B1 B A1 B1 A A1 A B1 A A A A A B A A B B B1 B B B B D B B1 D B C B C A1 C B1 A B1 A A A A A1 A A Hast C-276 A A A1 B B2 A A B2 B1 B A1 B A B B1 A B1 B1 B A B B1 A B1 B B C B B1 A A B2 B1 A1 B1 B B1 A1 B B A A A A A A A A A1 B B B1 Elgiloy A A A A A A A A A A A A A A A C B B C B C A A A A A A A A A A Gasoline Gelatin Glucose Glue, PVA Glycerin Glycolic acid Grape juice Grease Heptane Hexane Honey Hydraulic oil (Petro) Hydraulic oil (Synthetic) Hydrazine Hydrobromic acid 20% Hydrobromic acid 100% Hydrochloric acid 20% Hydrochloric acid 37% Hydrochloric acid 100% Hydrocyanic acid Hydrocyanic acid gas 10% Hydrofluoric acid 20% Hydrofluoric acid 50% Hydrofluoric acid 75% Hydrofluoric acid 100% Hydrofluorosilicic acid 20% Hydrofluorosilicic acid 100% Hydrogen gas Hydrogen peroxide 10% Hydrogen peroxide 30% Hydrogen peroxide 50% Hydrogen peroxide 100% Hydrogen sulfide (aqua) Hydrogen sulfide (dry) Hydroquinone Hydroxyacetic acid 70% Iodine Isopropyl acetate Isopropyl ether Jet fuel (JP3,4,5,6,8) Jet fuel (JP9, 10) Kerosene Ketones Lacquer thinners Lacquers Lactic acid Lard Latex Lead acetate Lead sulfamate Ligroin Lime Lubricants Magnesium carbonate Magnesium chloride Magnesium hydroxide Magnesium nitrate Magnesium sulfate Maleic acid Medias PTFE B A A A A A A A A A A A A C A A A A A A A A A A A A A A A A A A A A A A A A1 A A A A A A A A A A B A A1 A A1 A A A A A UHMW PE A A2 A2 A1 A1 A2 B B1 D B C A B2 B1 A2 B2 A2 A2 A1 C1 B2 B1 A2 A C2 C2 C2 A A A A A1 B1 B D D C1 C1 A A A1 A A2 A1 A A D B A1 A2 A2 A2 B2 TPE A A A A C B C C D D D A A B C C D D A C C 301 SS A A2 A1 A1 A2 A A A A A A A A D D D D D B1 D D D B1 C2 D A B2 B2 B2 B2 C C1 B D C A A A A A A1 A1 B1 A A2 B C A A2 B D B B A A Hast C-276 A A A A A A A A A A A A A C A1 B A A B B B B B B A A A A A A A B A B A A A B A A A B1 A A B1 A B A2 A A B B Elgiloy A A A A A A A A A A A A A C D B C B C C C C C C A D D D D A A D A A A A A A A A A A A A A
Cresols Cresylic acid Cyclohexane Cyclohexanone Detergents Diacetone alcohol Dichloroethane Diesel fuel Diethyl ether Diethylamine Diethylene glycol Dimethyl formamide Diphenyl oxide Epsom salts Ethane Ethanol Ethanolamine Ether Ethyl acetate Ethyl benzoate Ethyl chloride Ethylene bromide Ethylene chloride Ethylene chlorohydrin Ethylene diamine Ethylene dichloride Ethylene glycol Ethylene oxide Fatty acids Ferric chloride Ferric nitrate Ferric sulfate Ferrous chloride Ferrous sulfate Fluorine Fluoroboric acid Fluosilcic acid Formaldehyde 40% Formaldehyde 100% Formic acid Freon 11 Freon 12 Freon 22 Freon 113 Freon TF Fruit juice Fuel oils Furan resin Furfural Gallic acid
01/15/06
C-2
www.parkerseals.com
Medias Malic acid Mayonnaise Melamine Mercuric chloride (dilute) Mercuric cyanide Mercury Methane Methanol Methyl acetate Methyl acrylate Methyl alcohol 10% Methyl bromide Methyl cellosolve Methyl chloride Methyl dichloride Methyl ethyl ketone (MEK) Methyl isobutyl ketone Methyl isopropyl ketone Methylamine Methylene chloride MIL-H-5606 MIL-L-7808 MIL-L-23699 MIL-H-46170 Milk Mineral spirits Molasses Monoethanolamine Mustard Naphtha Naphthalene Nickel chloride Nickel sulfate Nitric acid (5 10%) Nitric acid (20%) Nitric acid (50%) Nitric acid (concentrated) Nitrobenzene Nitrous acid Nitrous oxide Oils: Aniline Castor Cocoa Nut Cod Liver Corn Cotton Seed Creosote Diesel fuel Fuel Ginger Lemon Linseed Mineral Olive Orange Palm Peanut Peppermint A A A A A A A A A A A A A A1 A A A A A A C A B A B1 A1 C1 A A D B1 A A1 D A1 A B1 A A A A A A A B A A D A A A A A A A A B A A A A B B A1 B A A A A A A A A A A A A A A A A A A A A A PTFE A A A A B A A A A A A A A A A A A A A A A A A A A A A B A A A2 A A A A A A A UHMW PE B2 D A A A A1 B1 A1 C1 C1 B2 C D A1 C A B A C A A1 C A A B C B1 C1 C1 C TPE B B B B B B D B B C D D D D 301 SS A C D C A A A A A A A B A A B A A B A A A A A A A A A A A D B A A A2 A1 B B B Hast C-276 B A C A A2 A A A A B A A B A B A A B A B B A1 A1 A1 B1 D D B Elgiloy A D A A A A A B A A A A A A A A A A C A A A A Medias Oils (Continued): Pine Rapeseed Rosin Sesame Seed Silicone Soybean Tanning Transformer Turbine Oleic acid Oleum 25% Oleum 100% Oxalic acid (cold) Ozone Paraffin Pentane Perchloric acid Perchloroethylene Petrolatum Phenol (10%) Phosphoric acid (<40%) Phosphoric acid (>40%) Phosphoric acid (crude) Photographic developer Phthalic anhydride Picric acid Potash Potassium bicarbonate Potassium bromide Potassium chlorate Potassium chloride Potassium chromate Potassium cyanide sols. Potassium dichromate Potassium ferrocyanide Potassium hydroxide Potassium nitrate Potassium permanganate Potassium sulfate Potassium sulfide Propane (liquefied) Propylene glycol Pyridine Pyrogallic acid Rosins Rum Rust inhibitors Salad dressings Sea water Shellac (bleached) Silicone Silver bromide Silver nitrate Skydrol 500B Soap solutions Sodium acetate Sodium aluminate Sodium bicarbonate A A A A A A A A A A A A1 A A A A A C A A A A A A A A A A A A1 A A A A A A A A A A A A A A A A A A A A A A A D D B2 A A1 C1 C C2 D D A2 A B D B D B B A B1 B1 A A A1 A A A1 A1 A A A A1 A B A A2 A2 C1 B2 B1 B1 A2 A1 A A D A A2 A B A C D C C D B B C D B D B A C A A D A A A A1 A A A A A A A B2 A B B A C C B A B D D D A A B B B B B1 B1 B1 B1 B B B B B1 B1 B A B A B2 A1 A A A C A A D B A A B A A A A A A2 A D B B A B B A B A2 A2 A2 B A B B B B B A A B B B B1 B1 A1 B1 A B B B A A A A A B B1 A A A A A A A A A A B A A A B C A B B B A B A A A A A A A A A PTFE UHMW PE TPE 301 SS Hast C-276 Elgiloy
01/15/06
C-3
www.parkerseals.com
Medias Sodium bisulfate Sodium bisulfite Sodium borate Sodium carbonate Sodium chlorate Sodium chloride Sodium chromate Sodium cyanide Sodium fluoride PTFE A A A A A A A A A1 A A A1 A A A A A A A A A A A A A A A A A A A A A A A A A UHMW PE A2 A2 A2 B2 B2 A2 A2 A2 D D D B2 A A1 A2 A1 A A A2 A2 B1 A2 A1 A2 B2 B B1 C1 A2 C1 A1 B TPE C B B A B B C D A C C D C 301 SS D B1 B2 A A B B1 A1 D B B C D C A A A B1 B A B A B B B A2 D C2 A B A A A B D D A Hast C-276 B2 B A A B1 A A A A B C A1 B A A B B B A B B B1 B B B B A D A B A B Elgiloy A A B B B B C B B A C B A A B A B Medias Sulfur trioxide (dry) Sulfuric acid (10 75%) Sulfuric acid (75 100%) Sulfuric acid (<10%) Sulfuric acid (cold conc) Sulfuric acid (hot conc) Sulfurous acid Tallow Tannic acid Tanning liquors Tartaric acid Tetrachloroethane Tetrachloroethylene Tetrahydrofuran Tin Salts Toluene (toluol) Trichloroacetic acid Trichloroethane Trichloroethylene Trichloropropane Tricresyl phosphate Triethylamine Trisodium phosphate Turpentine Urea Uric acid Varnish Vegetable juice Vinegar Water acid, mine Water, distilled Water, fresh Water, salt Whiskey & wines White liquor (pulp mill) Xylene Zinc chloride PTFE A A A A A A A A A A A A A A A A A A A A1 A A A A A A A A A A A A A A A A A UHMW PE C1 A1 B1 A1 C D B2 C B2 A1 A1 B C1 C1 A D B1 A D A B A A A2 A2 A2 A2 C A2 B A1 TPE C A B A C B B C A A A B A 301 SS D D C D C D B1 A B1 A2 C2 B A A D B B A B A B A B B A A A B A A B A A B B Hast C-276 B B1 B1 B1 A1 D B B1 B B A A C A B A A A A A B B B A A A A A A A A B Elgiloy D C D C D A B A A A A A A A A A B A A A A A A A A A A
Sodium hydroxide (20%) Sodium hydroxide (50%) Sodium hydroxide (80%) Sodium hypochlorite (100%) Sodium hypochlorite (<20%) Sodium hyposulfite Sodium metaphosphate Sodium metasilicate Sodium nitrate Sodium perborate Sodium peroxide Sodium polyphosphate Sodium silicate Sodium sulfate Sodium sulfite Sodium tetraborate Sodium thiosulfate (hypo) Stannic chloride Stannous chloride Starch Stearic acid Stoddard solvent Styrene Sugar (liquids) Sulfate (liquors) Sulfur chloride Sulfur dioxide (dry) Sulfur hexaflouride Sulfur trioxide
Note: Chemical compatibility ratings on this and preceding pages are intended only as a guide for the users initial selection. Actual compatibility may be different based on application parameters including pressure, temperature and specific media contents and percentages. Actual testing in the specific application media and operating parameters is the responsibility of the user to determine final material selection and approval. Please call Parker EPS Application Engineering with any questions regarding material selection at (801) 972-3000.
01/15/06
C-4
www.parkerseals.com
ISO Tolerances
Limits in Millimeters
Above 3 mm 6 mm 10 mm 18 mm 30 mm 50 mm 80 mm 120 mm 180 mm 250 mm 315 mm 400 mm 500 mm 630 mm 800 mm 1000 mm Up to and Including 3 mm 6 mm 10 mm 18 mm 30 mm 50 mm 80 mm 120 mm 180 mm 250 mm 315 mm 400 mm 500 mm 630 mm 800 mm 1000 mm 1250 mm H9 +.025 -.000 +.030 -.000 +.036 -.000 +.043 -.000 +.052 -.000 +.062 -.000 +.074 -.000 +.087 -.000 +.100 .000 +.115 -.000 +.130 -.000 +.140 -.000 +.155 -.000 +.175 -.000 +.200 -.000 +.230 -.000 +.260 -.000 h9 +.000 -.025 +.000 -.030 +.000 -.036 +.000 -.043 +.000 -.052 +.000 -.062 +.000 -.074 +.000 -.087 +.000 -.100 +.000 -.115 +.000 -.130 +.000 -.140 +.000 -.155 +.000 -.175 +.000 -.200 +.000 -.230 +.000 -.260
01/15/06
D-1
www.parkerseals.com
Catalog EPS00-0000/US [?]
Notes
D-2
www.parkerseals.com
Other Parker EPS Products

Parker EPS Division
Parker EPS Division designs and manufactures engineered elastomeric, polymeric and plastic seals and sealing systems for dynamic applications. EPS Division has a worldwide sealing network consisting of manufacturing locations in Utah, Texas, New York, Illinois and Baja, Mexico; and more than 200 distributor and service center locations in nine countries.
Rod Seals
Parker is the premiere manufacturer of quality rod sealing products both in standard inch as well as metric sizes, in a wide range of urethane and traditional elastomer compounds. See: Catalog EPS 3800 & 5225
Catalog Services
EPS Divisions catalogs and technical bulletins are available through Parkers Catalog Services. To order catalogs and have them shipped directly, call 1-800-C-PARKER, or send your requests via e-mail to: [email protected].
Piston Seals
Parker is pleased to provide a diverse offering of piston seal profiles to suit a broad range of applications. Various cap materials extend service to a broad range of application pressures and temperatures. See: Technical Bulletins EPS 5212, 5206, 5238, 5301, 5302
Technical Support
Parker product engineers are available to address temperature, pressure, gland design, surface finish and all other seal design considerations, and can often optimize an existing design or propose cost-effective alternatives. Our in-house test and R&D laboratories enable us to quickly develop and perform appropriate test protocols for our customers.
Rod Wipers & Scrapers

Parker is the leading manufacturer of rod wipers and scrapers in a variety of geometries to suit any rod application. Parkers rod wipers are offered in a wide range of urethanes as well as traditional elastomers in standard inch and metric sizes. See: Catalog PPD 3600
U-Cup Seals
Parkers U-cup seals are compact and versatile. Varying lip design configurations coupled with the broad range of available Parker materials mean versatility in U-cup sealing, both in hydraulic and pneumatic applications. See: Catalog PPD 5225
E-1
www.parkerseals.com
Other Parker EPS Products Finite Element Analysis & Seal Design Optimization
Using sophisticated Finite Element Analysis (FEA) software, Parker engineers can analyze critical design information, such as stress concentration, heat transfer, fluid flow and electromagnetic properties of new and existing seal geometry. This streamlines tooling and production processes, and helps ensure the selection of the right material and geometry for your application. Using FEA technology, our engineers can determine: Deformation (deformed shape)
Wear Rings and Bearings

Parker is pleased to offer a complete line of MolyGard, WearGard and PTFE wear rings and bearing products to fit any application. Expertise in both engineered hard plastics and in PTFE makes Parker the global leader for reciprocating bearing materials. By incorporating premium material blends with precision machining tolerances (down to .001"), Parker meets the full spectrum of needs, from heavy duty hydraulic cylinders operating under the highest temperatures and pressures to pneumatic applications requiring low friction, long life and self-lubrication. See: Catalog EPS 5276
Volume/void ratios, gland fill % Stress distribution

FEA plot of a Parker Seal geometry under compression
Integrated Piston Assembly

Parkers Integrated Piston combines the piston, bearing and seal into a self-contained package for low, medium and high pressure hydraulic cylinder applications. See: Catalog EPS 5220
Load - Deflection Stability analysis Friction force Thermal effects Material evaluation Seal life prediction
ProTech Bearing Isolators

ProTech bearing isolators are the ultimate in bearing protection with unitized, two-piece, non-contact design. ProTech provides zero lubricant leakage and total exclusion of contaminants. See: Catalog EPS 5275
Rotary Shaft Oil Seals

Parker offers a complete line of oil seal products including the proprietary Clipper Oil Seal design with integrally molded rubber/fiber outer case and elastomeric inner lip. Varying profiles include factory split, MIST, single-lip, dual-lip, excluder and molded-in spring. Parker Oil Seals are elastomer-lipped, metal-retained rotary shaft seals available in a multitude of configurations. See: Catalog EPS 5350
01/15/06 01/15/06
E-2
www.parkerseals.com
Notes
E-3
www.parkerseals.com
About Parker Hannifin Corporation
Parker Hannifin is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 500 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control motion in some 1,200 industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic and electromechanical motion-control solutions. Our company has the largest distribution network in its field, with over 7,500 distributors serving more than 400,000 customers worldwide. The Aerospace Group
is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high-technology markets, while achieving growth through premier customer service.
The Climate & Industrial Controls Group

designs, manufactures and markets system-control and fluid-handling components and systems to refrigeration, airconditioning and industrial customers worldwide.
The Fluid Connectors Group

designs, manufactures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems.
The Seal Group

designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction.
The Hydraulics Group

designs, produces and markets a full spectrum of hydraulic components and systems to builders and users of industrial and mobile machinery and equipment.
The Filtration Group

designs, manufactures and markets quality filtration and clarification products, providing customers with the best value, quality, technical support and global availability.
The Automation Group

is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide.
The Instrumentation Group

is a global leader in the design, manufacture and distribution of high-quality critical flow components for worldwide process instrumentation, ultrahigh-purity, medical and analytical applications.
Parkers Charter
To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifically, we will design, market and manufacture products controlling motion, flow and pressure. We will achieve profitable growth through premier customer service.
Product Information
North American customers seeking product information, the location of a nearby distributor, or repair services will receive prompt attention by calling Parker Product Information Center at our toll-free number: 1-800-C-PARKER (1-800-2727537). In Europe, call 00800-C-PARKER-H (00800-2727-5374).
01/15/06
E-4
www.parkerseals.com
Offer of Sale
The items described in this document are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer (Buyer) shall be governed by all of the following Terms and Conditions. Buyers order for any item described in this document, when communicated to Parker Hannifin Corporation, its subsidiary or any authorized distributor (Seller) verbally or in writing, shall constitute acceptance of this offer.
1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgements, acceptances and sales of Sellers products are subject to and shall be governed exclusively by the terms and conditions stated herein. Buyers acceptance of any offer to sell is limited to these terms and conditions. Any terms or conditions in addition to, or inconsistent with those stated herein, proposed by Buyer in any acceptance of an offer by Seller, are hereby objected to. No such additional, different or inconsistent terms and conditions shall become part of the contract between Buyer and Seller unless expressly accepted in writing by Seller. Sellers acceptance of any offer to purchase by Buyer is expressly conditional upon Buyers assent to all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in Buyers offer. Acceptance of Sellers products shall in all events constitute such assent. 2. Payment: Payment shall be made by Buyer net 30 days from the date of invoice of the items purchased hereunder. Seller reserves the right to charge interest on all past due amounts. Any claims by Buyer for omissions or shortages in a shipment shall be waived unless Seller receives notice thereof within 30 days after Buyers receipt of the shipment. 3. Delivery: Unless otherwise provided in the face hereof, delivery shall be made F.O.B. Sellers plant. Regardless of the method of delivery, however, risk of loss shall pass to Buyer upon Sellers delivery to a carrier. Any delivery dates shown are approximate only and Seller shall have no liability for any delays in delivery. 4. Warranty: Seller warrants that the items sold hereunder shall be free from defects in material or workmanship at the time of delivery. THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER. ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, MERCHANTIBILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED. NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIALLY, TO BUYERS DESIGNS OR SPECIFICATIONS. 5. Limitation of Remedy: SELLERS LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID BY BUYER, AT SELLERS SOLE OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING, BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY. 6. Changes, Reschedules and Cancellations: Buyer may request to modify the designs or specifications for the items sold hereunder as well as the quantities and delivery dates thereof, or may request to cancel all or part of this order, however, no such requested modification or cancellation shall become part of the contract between Buyer and Seller unless accepted by Seller in a written amendment to this Agreement. Acceptance of any such requested modification or cancellation shall be at Sellers discretion, and shall be upon such terms and conditions as Seller may require. 7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture items sold pursuant to this contract. Such special tooling shall be and remain Sellers property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the items sold hereunder, even if such apparatus has been specially converted or adapted for such manufacture and notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time. 8. Buyers Property: Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished by Buyer or any other items which become Buyers property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without Buyer placing an order for the items which are manufactured using such property. Seller shall not be responsible for any loss or damage to such property while it is in Sellers possession or control. 9. Taxes: Unless otherwise indicated on the face hereof, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by Seller or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. Buyer agrees to pay all such taxes or to reimburse Seller therefor upon receipt of its invoice. If Buyer claims exemption from any sales, use or other tax imposed by any taxing authority, Buyer shall save Seller harmless from and against any such tax, together with any interest or penalties thereon which may be assessed if the items are held to be taxable. 10. Indemnity for Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks, copyrights, trade dress and trade secrets (hereinafter Intellectual Property Rights). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. Sellers obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after the Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using said item, place or modify said item so as to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to items delivered hereunder for which the designs are specified in whole or part by Buyer, or infringements resulting from the modification, combination or use in a system of any item sold hereunder. The foregoing provisions of this Part 10 shall constitute Sellers sole and exclusive liability and Buyers sole and exclusive remedy for infringement of Intellectual Property Rights. If a claim is based on information provided by Buyer or if the design for an item delivered hereunder is specified in whole or in part by Buyer, Buyer shall defend and indemnify Seller for all costs, expenses or judgements resulting from any claim that such item infringes any patent, trademark, copyright, trade dress, trade secret or any similar right. 11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Sellers obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter Events of Force Majeure). Events of Force Majeure shall include without limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fires, floods, delays or failures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Sellers control. 12. Any special requirements for items to be provided by Seller hereunder including without limitation; compliance with military specifications, special documentation, or testing requirements, must be communicated to Seller in writing at the time the items are first requested. Any such requests that are communicated to Seller after preparation to manufacture an item has commenced may result in additional charges for rework or remanufacture of the item. 13. Entire Agreement/Governing Law: The terms and conditions set forth herein, together with any amendments, modifications and any different terms or conditions expressly accepted by Seller in writing, shall constitute the entire Agreement concerning the items sold, and there are no oral or other representations or agreements which pertain thereto. This Agreement shall be governed in all respects by the law of the State of Ohio. No actions arising out of the sale of the items sold hereunder or this Agreement may be brought by either more than two (2) years after the cause of action accrues.
www.parkerseals.com
Parker Hannifin Corporation Seal Group Engineered Polymer Systems Division Salt Lake City Operations and Headquarters 2220 South 3600 West Salt Lake City, UT 84119 USA Ph: 801-972-3000 Fax: 801-973-4019 Nacogdoches Operations 403 Industrial Drive Nacogdoches, TX 75963 USA Ph: 936-560-8900 Fax: 936-560-8998 Toll Free: 1-800-233-3900 Redmond Operations 3967 Buffalo Street Marion, NY 14505 USA Ph: 315-926-4211 Fax: 315-926-4498 Chicago Operations 2565 Northwest Parkway Elgin, IL 60123 USA Ph: 847-783-4300 Fax: 847-783-4301
Your Authorized Parker Seal Distributor

Parker Hannifin Corporation Corporate Office 6035 Parkland Blvd. Cleveland, OH 44124-4141 USA Ph: 216-896-3000 Fax: 216-896-4000 1-800-C-PARKER www.parkerseals.com
01/06 3.0M AP

Parker - PTFE Lip Seals

Uploaded by

Copyright:

Available Formats

Parker - PTFE Lip Seals

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Parker - PTFE Lip Seals

Uploaded by

Copyright:

Available Formats

PTFE Lip Seal Design Guide

Catalog EPS 5340/USA

2006 Parker Hannifin Corporation

PTFE Lip Seal Design Guide Table of Contents

FlexiLip Rotary Seals

FlexiCase Rotary Seals

Design Action Request Form

Problem Solved Case Studies

PTFE Lip Seal Design Guide Appendix

Other Parker Products

Catalog EPS 5340/USA

Catalog EPS 5340/USA

FBC-V FRC-V FPC-V

FBS-V FRS-V FPS-V

FBG-V FRG-V FPG-V

FBD-V FRD-V FPD-V

FBK-V FRK-V FPK-V

FBM-V FRM-V FPM-V

FBL-V FRL-V FPL-V

FBN-H FRN-H FPN-H

FBN-C FRN-C FPN-C

For additional information on all profiles, see Tab 4.

Catalog EPS 5340/USA

Introduction Engineering Excellence

Aircraft Engines Require High Temperature Ratings

Catalog EPS 5340/USA

Motors Require Wear Resistance

Control Valves Require Low Friction

Catalog EPS 5340/USA

How does the FlexiSeal work?

FlexiSeal Design Function

How do I choose the right profile for my application?

Catalog EPS 5340/USA

Engineering Testing and Validation

Catalog EPS 5340/USA

Engineering Gland Designs and Installation

Two-Piece Rod and Piston Glands

Two-Piece Gland Installation

Table 2-1. Heel First Recommended Lead-In Chamfer

Figure 2-1. Two-Piece Gland Heel First Installation

Note: Complete gland dimensions are provided in Tabs 5 9.

Catalog EPS 5340/USA

Figure 2-2. Two-Piece Gland Lips First Installation

Note: Complete gland dimensions are provided in Tabs 5 9.

Two-Piece Flanged Glands

Figure 2-3. Two-Piece Flanged Gland

Catalog EPS 5340/USA

Step Cut Glands

Table 2-3. Nominal Cross-Sections

C1 Min. 0.035 0.050 0.065 0.080 0.095

Step Cut Gland Installation

Figure 2-4. Step Cut Gland Installation

Catalog EPS 5340/USA

Heel First with Snap Ring

Lips First with Support Ring and Snap Ring

Figure 2-5. Alternative Installations

Table 2-4. Rod Seals Suitable for Solid Grooves

Table 2-5. Piston Seals Suitable for Solid Grooves

Closed Glands 01/15/06

Catalog EPS 5340/USA