Turning circles

The turning circle of a car is the diameter of the circle described by the outside wheels when turning on full lock. There is no hard and fast forumla to calculate the turning circle but you can get close by using this: turning circle radius = (track/2) + (wheelbase/sin(average steer angle)) The numbers required to calculate the turning circle explain why a classic black London taxi has a tiny 8m turning circle to allow it to do U-turns in the narrow London streets. In this case, the wheelbase and track aren't radically different to any other car, but the average steering angle is huge. For comparison, a typical passenger car turning circle is normally between 11m and 13m with SUV turning circles going out as much as 15m to 17m. Like the site? The page you're reading is free, but if you like what you see and feel you've learned something, a small donation would be appreciated to help me pay my server space. Thank you.

Steering System designs : Pitman arm types

There really are only two basic categories of steering system today; those that have pitman arms with a steering 'box' and those that don't. Older cars and some current trucks use pitman arms, so for the sake of completeness, I've documented some common types. Newer cars and unibody light-duty trucks typically all use some derivative of rack and pinion steering.

Pitman arm mechanisms have a steering 'box' where the shaft from the steering wheel comes in and a lever arm comes out - the pitman arm. This pitman arm is linked to the track rod or centre link, which is supported by idler arms. The tie rods connect to the track rod. There are a large number of variations of the actual mechanical linkage from direct-link where the pitman arm is connected directly to the track rod, to compound linkages where it is connected to one end of the steering system or the track rod via other rods. The example here shows a compound link (left). Most of the steering box mechanisms that drive the pitman arm have a 'dead spot' in the centre of the steering where you can turn the steering wheel a slight amount before the front wheels start to turn. This slack can normally be adjusted with a screw mechanism but it can't ever be eliminated. The traditional advantage of these systems is that they give bigger mechanical advantage and thus work well on heavier vehicles. With the advent of power steering, that has become a moot point and the steering system design is now more to do with mechanical design, price and weight. The following are the four basic types of steering box used in pitman arm systems.

Worm and sector

In this type of steering box, the end of the shaft from the steering wheel has a worm gear attached to it. It meshes directly with a sector gear (so called because it's a section of a full gear wheel). When the steering wheel is turned, the shaft turns the worm gear, and the sector gear pivots around its axis as its teeth are moved along the worm gear. The sector gear is mounted on the cross shaft which passes through the steering box and out the bottom where it is splined, and the the pitman arm is attached to the splines. When the sector gear turns, it turns the cross shaft, which turns the pitman arm, giving the output motion that is fed into the mechanical linkage on the track rod. The following diagram shows the active components that are present inside the worm and sector steering box. The box itself is sealed and filled with grease.

Worm and roller

The worm and roller steering box is similar in design to the worm and sector box. The difference here is that instead of having a sector gear that meshes with the worm gear, there is a roller instead. The roller is mounted on a roller bearing shaft and is held captive on the end of the cross shaft. As the worm gear turns, the roller is forced to move along it but because it is held captive on the cross shaft, it twists the cross shaft. Typically in these designs, the worm gear is actually an hourglass shape so that it is wider at the ends. Without the hourglass shape, the roller might disengage from it at the extents of its travel.

Worm and nut or recirculating ball

This is by far the most common type of steering box for pitman arm systems. In a recirculating ball steering box, the worm drive has many more turns on it with a finer pitch. A box or nut is clamped over the worm drive that contains dozens of ball bearings. These loop around the worm drive and then out into a recirculating channel within the nut where they are fed back into the worm drive again. Hence recirculating. As the steering wheel is turned, the worm drive turns and forces the ball bearings to press against the channel inside the nut. This forces the nut to move along the worm drive. The nut itself has a couple of gear teeth cast into the outside of it and these mesh with the teeth on a sector gear which is attached to the cross shaft just like in the worm and sector mechanism. This system has much less free play or slack in it than the other designs, hence why it's used the most. The example below shows a recirculating ball mechanism with the nut shown in cutaway so you can see the ball bearings and the recirculation channel.

Cam and lever

Cam and lever steering boxes are very similar to worm and sector steering boxes. The worm drive is known as a cam and has a much shallower pitch and the sector gear is replaced with two studs that sit in the cam channels. As the worm gear is turned, the studs slide along the cam channels which forces the cross shaft to rotate, turning the pitman arm. One of the design features of this style is that it turns the cross shaft 90 to the normal so it exits through the side of the steering box instead of the bottom. This can result in a very compact design when necessary.

Steering System designs : Rack and pinion

This is by far the most common type of steering you'll find in any car today due to it's relative simplicity and low cost. Rack and pinion systems give a much better feel for the driver, and there isn't the slop or slack associated with steering box pitman arm type systems. The downside is that unlike those systems, rack and pinion designs have no adjustability in them, so once they wear beyond a certain mechanical tolerance, they need replacing completely. This is rare though. In a rack and pinion system, the track rod is replaced with the steering rack which is a long, toothed bar with the tie rods attached to each end. On the end of the steering shaft there is a simple pinion gear that meshes with the rack. When you turn the steering wheel, the pinion gear turns, and moves the rack from left to right. Changing the size of the pinion gear alters the steering ratio. It really is that simple. The diagrams here show an example rack and pinion system (left) as well as a close-up cutaway of the steering rack itself (right).

Variable-ratio rack and pinion steering

This is a simple variation on the above design. All the components are the same, and it all works the same except that the spacing of the teeth on the rack varies depending on how close to the centre of the rack they are. In the middle, the teeth are spaced close together to give slight steering for the first part of the turn - good for not oversteering at speed. As the teeth get further away from the centre, they increase in spacing slightly so that the wheels turn more for the same turn of the steering wheel towards full lock. Simple.

Vehicle dynamics and steering - how it can all go very wrong

Generally speaking, when you turn the steering wheel in your car, you typically expect it to go where you're pointing it. At slow speed, this will almost always be the case but once you get some momentum behind you, you are at the mercy of the chassis and suspension designers. In racing, the aerodynamic wings, air splitters and undertrays help to maintain an even balance of the vehicle in corners along with the position of the weight in the vehicle and the supension setup. The two most common problems you'll run into are understeer and oversteer.

Understeer

Understeer is so called because the car steers less than you want it to. Understeer can be brought on by all manner of chassis, suspension and speed issues but essentially it means that the car is losing grip on the front wheels. Typically it happens as you brake and the weight is transferred to the front of the car. At this point the mechanical grip of the front tyres can simply be overpowered and they start to lose grip (for example on a wet or greasy road surface). The end result is that the car will start to take the corner very wide. In racing, that normally involves going off the outside of the corner into a catch area or on to the grass. In normal you-and-me driving, it means crashing at the outside of the corner. Getting out of understeer can involve letting off the throttle in front-wheel-drive vehicles (to try to give the tyres chance to grip) or getting on the throttle in rear-wheel-drive vehicles (to try to bring the back end around). It's a complex topic more suited to racing driving forums but suffice to say that if you're trying to get out of understeer and you cock it up, you get.....

Oversteer