GD&T

TECHNICAL HANDBOOK
Contents
Section 1 Technical Drawings Surface Texture Geometrical Tolerancing Sheet Sizes, Title Block, Non-standard Formats Drawings Suitable for Microfilming Section 2 Standardization ISO Metric Screw Threads (Coarse Pitch Threads) ISO Metric Screw Threads (Coarse and Fine Pitch Threads) Cylindrical Shaft Ends ISO Tolerance Zones, Allowances, Fit Tolerances Parallel Keys, Taper Keys, and Centre Holes Section 3 Physics Internationally Determined Prefixes Basic SI Units Derived SI Units Legal Units Outside the SI Physical Quantities and Units of Lengths and Their Powers Physical Quantities and Units of Time Physical Quantities and Units of Mechanics Physical Quantities and Units of Thermodynamics and Heat Transfer Physical Quantities and Units of Electrical Engineering Physical Quantities and Units of Lighting Engineering Different Measuring Units of Temperature Measures of Length and Square Measures Cubic Measures and Weights Energy, Work, Quantity of Heat Power, Energy Flow, Heat Flow Pressure and Tension Velocity Equations for Linear Motion and Rotary Motion Section 4 Mathematics/Geometry Calculation of Areas Calculation of Volumes Section 5 Mechanics/Strength of Materials Axial Section Moduli and Axial Second Moments of Area (Moments of Inertia) of Different Profiles Deflections in Beams Values for Circular Sections Stresses on Structural Members and Fatigue Strength of Structures
Page 23/24 25-38 39 40/41
43 44 45 46/47 48
50 50 51 51 52 53 53/55 55/56 56 57 57 58 59 59 60 60 60 61
63 64
66 67 68 69
18
19
Contents
Contents
Section 6 Hydraulics Hydrostatics Hydrodynamics
Page 71 72
Section 7 Electrical Engineering Basic Formulae 74 Speed, Power Rating and Efficiency of Electric Motors 75 Types of Construction and Mounting Arrangements of Rotating Electrical Machinery 76 Types of Protection for Electrical Equipment (Protection Against Contact and Foreign Bodies) 77 Types of Protection for Electrical Equipment (Protection Against Water) 78 Explosion Protection of Electrical Switchgear 79/80 Section 8 Materials Conversion of Fatigue Strength Values of Miscellaneous Materials Mechanical Properties of Quenched and Tempered Steels Fatigue Strength Diagrams of Quenched and Tempered Steels General-Purpose Structural Steels Fatigue Strength Diagrams of General-Purpose Structural Steels Case Hardening Steels Fatigue Strength Diagrams of Case Hardening Steels Cold Rolled Steel Strips for Springs Cast Steels for General Engineering Purposes Round Steel Wire for Springs Lamellar Graphite Cast Iron Nodular Graphite Cast Iron Copper-Tin- and Copper-Zinc-Tin Casting Alloys Copper-Aluminium Casting Alloys Aluminium Casting Alloys Lead and Tin Casting Alloys for Babbit Sleeve Bearings Comparison of Tensile Strength and Miscellaneous Hardness Values Values of Solids and Liquids Coefficient of Linear Expansion Iron-Carbon Diagram Fatigue Strength Values for Gear Materials Heat Treatment During Case Hardening of Case Hardening Steels Section 9 Lubricating Oils Viscosity-Temperature-Diagram for Mineral Oils Viscosity-Temperature-Diagram for Synthetic Oils of Poly--Olefine Base Viscosity-Temperature-Diagram for Synthetic Oils of Polyglycole Base Kinematic Viscosity and Dynamic Viscosity Viscosity Table for Mineral Oils
Section 10 Cylindrical Gear Units Symbols and Units General Introduction Geometry of Involute Gears Load Carrying Capacity of Involute Gears Gear Unit Types Noise Emitted by Gear Units Section 11 Shaft Couplings General Fundamental Principles Rigid Couplings Torsionally Flexible Couplings Torsionally Rigid Couplings Synoptical Table of Torsionally Flexible and Torsionally Rigid Couplings Positive Clutches and Friction Clutches Section 12 Vibrations Symbols and Units General Fundamental Principles Solution Proposal for Simple Torsional Vibrators Solution of the Differential Equation of Motion Symbols and Units of Translational and Torsional Vibrations Formulae for the Calculation of Vibrations Evaluation of Vibrations Section 13 Bibliography of Sections 10, 11, and 12
Page 106/107 108 108-119 119-127 127-130 131-134
82 83 84 85 86 87 88 89 89 90 90 91 92 92 93 94 95 96 97 97 97 98
136 136 136/138 138 139 140
142 143-145 145/146 146/147 148 149-151 151/152
153-155
100 101 102 103 104
20
21
Table of Contents Section 1
Technical Drawings Surface Texture
Technical Drawings Surface Texture Method of indicating surface texture on drawings acc. to DIN ISO 1302 Explanation of the usual surface roughness parameters Comparison of roughness values Geometrical Tolerancing General Application; general explanations Kinds of tolerances; symbols; included tolerances Tolerance frame Toleranced features Tolerance zones Datums and datum systems Theoretically exact dimensions Detailed definitions of tolerances Sheet Sizes, Title Blocks, Non-standard Formats Sheet sizes for technical drawings Title blocks for technical drawings Non-standard formats for technical drawings Drawings Suitable for Microfilming General Lettering Sizes of type Lines acc. to DIN 15 Part 1 and Part 2 Ink fountain pens Lettering example with stencil and in handwriting
Page
1. Method of indicating surface texture on drawings acc. to DIN 1302 1.1 Symbols
23 23 24
Symbol without additional indications. Basic symbol. The meaning must be explained by additional indications. Symbol with additional indications. Any production method, with specified roughness.
25 25 26 26 27 27 27-29 29 29-38
Symbol without additional indications. Removal of material by machining, without specified roughness. Symbol with additional indications. Removal of material by machining, with specified roughness. Symbol without additional indications. Removal of material is not permitted (surface remains in state as supplied). Symbol with additional indications. Made without removal of material (non-cutting), with specified roughness. 1.2 Position of the specifications of surface texture in the symbol a = Roughness value Ra in micrometres or microinches or roughness grade number N1 to N12 b = Production method, surface treatment or coating c = Sampling length d = Direction of lay e = Machining allowance f = Other roughness values, e.g. Rz Examples Production method Any Material removing Non-cutting Centre line average height Ra: maximum value = 0.8 m Mean peak-to-valley height Rz: maximum value = 25 m Mean peak-to-valley height Rz: maximum value = 1 m at cut-off = 0.25 mm 2. Explanation of the usual surface roughness parameters 2.1 Centre line average height Ra acc. to DIN 4768 The centre line average height Ra is the arithmetic average of the absolute values of the distances y between the profile heights and the centre line within the measuring length. This is equivalent to the height of a rectangle (Ag) with a length equal to the evaluation length lm and with an area equal to the sum of the areas enclosed between the roughness profile and the centre line (Aoi and Aui) (see figure 1). Explanation Ex lanation
39 39 39
40 40 40 40 41 41
22
23
Technical Drawings Surface Texture
Technical Drawings Geometrical Tolerancing
4. General 4.1 The particulars given are in accordance with the international standard DIN ISO 1101, March 1985 edition. This standard gives the principles of symbolization and indication on technical drawings of tolerances of form, orientation, location and runout, and establishes the appropriate geometrical definitions. The term geometrical tolerances is used in this standard as generic term for these tolerances. 4.2 Relationship between tolerances of size, form and position According to current standards there are two possibilities of making indications on technical drawings in accordance with: a) the principle of independence according to DIN ISO 8015 where tolerances of size, form and position must be adhered to independent of each other, i.e. there is no direct relation between them. In this case reference must be made on the drawing to DIN ISO 8015. b) the envelope requirements according to DIN 7167, according to which the tolerances of size, form and parallelism are in direct relation with each other, i.e. that the size tolerances limit the form and parallelism tolerances. In this case no special reference to DIN 7167 is required on the drawing. 5. Application; general explanations 5.1 Geometrical tolerances shall be specified on drawings only if they are imperative for the functioning and/or economical manufacture of the respective workpiece. Otherwise, the general tolerances according to DIN 7168 apply. 5.2 Indicating geometrical tolerances does not necessarily imply the use of any particular method of production, measurement or gauging. 5.3 A geometrical tolerance applied to a feature defines the tolerance zone within which the feature (surface, axis, or median plane) is to be contained. According to the characteristic which is to be tolerated and the manner in which it is dimensioned, the tolerance zone is one of the following: - the area within a circle; - the area between two concentric circles; - the area between two equidistant lines or two parallel straight lines; - the space within a cylinder; - the space between two coaxial cylinders; - the space between two parallel planes; - the space within a parallelepiped.
The toleranced feature may be of any form or orientation within this tolerance zone, unless a more restrictive indication is given. 5.4 Unless otherwise specified, the tolerance applies to the whole length or surface of the considered feature. 5.5 The datum feature is a real feature of a part, which is used to establish the location of a datum. 5.6 Geometrical tolerances which are assigned to features referred to a datum do not limit the form deviations of the datum feature itself. The form of a datum feature shall be sufficiently accurate for its purpose and it may therefore be necessary to specify tolerances of form for the datum features. 5.7 See Page 26 5.8 Tolerance frame The tolerance requirements are shown in a rectangular frame which is divided into two or more compartments. These compartments contain, from left to right, in the following order (see figures 3, 4 and 5): - the symbol for the characteristic to be toleranced; - the tolerance value in the unit used for linear dimensions. This value is preceded by the sign if the tolerance zone is circular or cylindrical; - if appropriate, the capital letter or letters identifying the datum feature or features (see figures 4 and 5)
Centre line
S A oi + S A ui
A g + S A oi ) S A ui
Figure 1
le = Sampling length lm = Evaluation length lt = Traversed length z1-z5 = Single irregularities
Start-up length
Run-out length
Figure 2 2.2 Mean peak-to-valley height Rz acc. to DIN 4768 The mean peak-to-valley height Rz is the arithmetic average of the single irregularities of five consecutive sampling lengths (see figure 2). Note: An exact conversion of the peak-to-valley height Rz and the centre line average height Ra can neither be theoretically justified nor empirically proved. For surfaces which are generated by manufacturing methods of the group metal cutting, a diagram for the conversion from Ra to Rz and vice versa is shown in supplement 1 to DIN 4768 Part 1, based on comparison measurements (see table Comparison of roughness values). 3. Comparison of roughness values
DIN ISO 1302 Roughness values Ra Roughness grade number m 0.025 0.05 in 1 N1 0.1 0.8 2 N2 0.25 1.6 0.1 4 N3 0.4 2.5 0.2 8 N4 0.8 4 0.4 16 N5 1.6 6.3 0.8 32 N6 3.15 12.5 1.6 63 N7 6.3 20 3.2 125 N8 12.5 31.5 6.3 250 N9 25 63 12.5 25 50
2.3 Maximum roughness height Rmax acc. to DIN 4768 (see figure 2) The maximum roughness height Rmax is the largest of the single irregularities z occurring over the evaluation length lm (in figure 2: z3). Rmax is stated in cases where the largest single irregularity (runaway) is to be recorded for reasons important for function. 2.4 Roughness grade numbers N.. acc. to DIN ISO 1302 In supplement 1 to DIN ISO 1302 it is recommended not to use roughness grade numbers. The N-grade numbers are most frequently used in America (see also table Comparison of roughness values).
Figure 3
Figure 4
500 1000 2000 N10 N11 N12 40 100 80 160 160 250
Figure 5
Suppl. 1 Roughness from to DIN values Rz to in m 4768/1
24
25
Remarks referred to the tolerance, for example 6 holes, 4 surfaces, or 6 x shall be written above the frame (see figures 6 and 7).
If it is necessary to specify more than one tolerance characteristic for a feature, the tolerance specifications are given in tolerance frames one below the other (see figure 8).
6 holes
6x
5.9 Toleranced features The tolerance frame is connected to the toler-anced feature by a leader line terminating with an arrow in the following way: - on the outline of the feature or an extension of the outline (but clearly separated from the dimension line) when the tolerance refers to the line or surface itself (see figures 9 and 10).
the points of a geometric feature (point, line, surface, median plane) must lie. The width of the tolerance zone is in the direction of the arrow of the leader line joining the tolerance frame to the feature which is toleranced, unless the tolerance value is preceded by the sign (see figures 15 and 16).
Figure 6
Figure 7
Figure 8
5.7 Table 1: Kinds of tolerances; symbols; included tolerances Tolerances Symbols Toleranced characteristics Straightness Flatness Form tolerances Circularity (Roundness) Cylindricity Parallelism O i t ti Orientation tolerances Perpendicularity Angularity Tolerances of position 1) Position Location tolerances Concentricity, Coaxiality Symmetry Runout tolerances Circular runout, Axial runout Included tolerances Straightness Straightness, Parallelism, Circularity Flatness Flatness Flatness Straightness, Flatness, Parallelism Circularity, Coaxiality 5.11.1 When a toleranced feature is referred to a datum, this is generally shown by datum letters. The same letter which defines the datum is repeated in the tolerance frame. To identify the datum, a capital letter enclosed in a frame is connected to a solid datum triangle (see figure 18). Figure 13 on the axis or the median plane when the tolerance refers to the common axis or median plane of two features (see figure 14). Figure 17 5.11 Datums and datum systems Datum features are features according to which a workpiece is aligned for recording the tolerated deviations. Figure 11 Figure 12 Figure 9 Figure 10 Figure 15 Figure 16
as an extension of a dimension line when the tolerance refers to the axis or median plane defined by the feature so dimensioned (see figures 11 to 13).
Where a common tolerance zone is applied to several separate features, the requirement is indicated by the words common zone above the tolerance frame (see figure 17).
Common zone
1) Tolerances of position always refer to a datum feature or theoretically exact dimensions. Table 2: Additional symbols Description Toleranced feature indications direct direct Dat m indications Datum by capital letter Theoretically exact dimension Note: Whether a tolerance should be applied to the contour of a cylindrical or symmetrical feature or to its axis or median plane, depends on the functional requirements. 5.10 Tolerance zones The tolerance zone is the zone within which all Symbols Figure 14
Figure 18
26
27
The datum triangle with the datum letter is placed: - on the outline of the feature or an extension of the outline (but clearly separated from the dimension line), when the datum feature is the line or surface itself (see figure 19).
A single datum is identified by a capital letter (see figure 25). A common datum formed by two datum features is identified by two datum letters separated by a hyphen (see figures 26 and 28). In a datum system (see also 5.11.2) the sequence of two or more datum features is important. The datum letters are to be placed in different compartments, where the sequence from left to right shows the order of priority, and the datum letter placed first should refer to the directional datum feature (see figures 27, 29 and 30).
Datum system formed by one plane and one perpendicular axis of a cylinder: Datum A is the plane formed by the plane contact surface. Datum B is the axis of the largest inscribed cylinder, the axis being at right angles with datum A (see figure 30).
larity tolerance specified within the tolerance frame (see figures 31 and 32).
Figure 19 Figure 30 as an extension of the dimension line when the datum feature is the axis or median plane (see figures 20 and 21). Figure 25 Figure 26
Secondary datum
Figure 31
Note: If there is not enough space for two arrows, one of them may be replaced by the datum triangle (see figure 21).
Primary datum
Tertiary datum
Figure 27 5.11.2 Datum system A datum system is a group of two or more datums to which one toleranced feature refers in common. A datum system is frequently required because the direction of a short axis cannot be determined alone. Datum formed by two form features (common datum):
5.12 Theoretically exact dimensions If tolerances of position or angularity are prescribed for a feature, the dimensions determining the theoretically exact position or angle shall not be toleranced. These dimensions are enclosed, for example 30 . The corresponding actual dimensions of the part are subject only to the position tolerance or angu-
Figure 32
5.13 Detailed definitions of tolerances Symbol Definition of the tolerance zone 5.13.1 Straightness tolerance The tolerance zone when projected in a Any line on the upper surface parallel to the plane is limited by two parallel straight plane of projection in which the indication is lines a distance t apart. shown shall be contained between two parallel straight lines 0.1 apart. Indication and interpretation
Figure 20 -
Figure 21
on the axis or median plane when the datum is: a) the axis or median plane of a single feature (for example a cylinder); b) the common axis or median plane formed by two features (see figure 22).
Figure 28 Figure 22 If the tolerance frame can be directly connected with the datum feature by a leader line, the datum letter may be omitted (see figures 23 and 24). Datum system formed by two datums (short axis A and directional datum B):
Figure 33
Figure 34 Any portion of length 200 of any generator of the cylindrical surface indicated by the arrow shall be contained between two parallel straight lines 0.1 apart in a plane containing the axis.
Figure 23
Figure 24
Figure 29
Figure 35
28
29
Symbol
Definition of the tolerance zone
Indication and interpretation
Symbol
Definition of the tolerance zone 5.13.4 Cylindricity tolerance
The tolerance zone is limited by a parallel- The axis of the bar shall be contained within epiped of section t1 t2 if the tolerance is a parallelepipedic zone of width 0.1 in the specified in two directions perpendicular vertical and 0.2 in the horizontal direction. to each other.
The tolerance zone is limited by two The considered surface area shall be coaxial cylinders a distance t apart. contained between two coaxial cylinders 0.1 apart.
Figure 36
Figure 37
Figure 45 5.13.5 Parallelism tolerance
Figure 46
The tolerance zone is limited by a cylinder The axis of the cylinder to which the tolerof diameter t if the tolerance value is ance frame is connected shall be contained preceded by the sign . in a cylindrical zone of diameter 0.08.
Parallelism tolerance of a line with reference to a datum line The tolerance zone when projected in a plane is limited by two parallel straight lines a distance t apart and parallel to the datum line, if the tolerance zone is only specified in one direction. The toleranced axis shall be contained between two straight lines 0.1 apart, which are parallel to the datum axis A and lie in the vertical direction (see figures 48 and 49).
Figure 38 5.13.2 Flatness tolerance
Figure 39
The tolerance zone is limited by two paral- The surface shall be contained between two lel planes a distance t apart. parallel planes 0.08 apart. Figure 47 Figure 48 Figure 49
Figure 40 5.13.3 Circularity tolerance
Figure 41
The toleranced axis shall be contained between two straight lines 0.1 apart, which are parallel to the datum axis A and lie in the horizontal direction.
The tolerance zone in the considered The circumference of each cross-section of plane is limited by two concentric circles the outside diameter shall be contained a distance t apart. between two co-planar concentric circles 0.03 apart.
Figure 50 Figure 51 The tolerance zone is limited by a parallelepiped of section t1 t2 and parallel to the datum line if the tolerance is specified in two planes perpendicular to each other. The toleranced axis shall be contained in a parallelepipedic tolerance zone having a width of 0.2 in the horizontal and 0.1 in the vertical direction and which is parallel to the datum axis A (see figures 53 and 54).
Figure 42
Figure 43 The circumference of each cross-section shall be contained between two co-planar concentric circles 0.1 apart.
Figure 52 Figure 44 Figure 53 Figure 54
30
31
Symbol
Symbol
Definition of the tolerance zone 5.13.6 Perpendicularity tolerance
Parallelism tolerance of a line with reference to a datum line The tolerance zone is limited by a cylinder The toleranced axis shall be contained in a of diameter t parallel to the datum line if cylindrical zone of diameter 0.03 parallel to the tolerance value is preceded by the the datum axis A (datum line). sign .
Perpendicularity tolerance of a line with reference to a datum line The tolerance zone when projected in a plane is limited by two parallel straight lines a distance t apart and perpendicular to the datum line. The toleranced axis of the inclined hole shall be contained between two parallel planes 0.06 apart and perpendicular to the axis of the horizontal hole A (datum line).
Figure 55 Parallelism tolerance of a line with reference to a datum surface
Figure 56 Figure 64 Figure 65
The tolerance zone is limited by two paral- The toleranced axis of the hole shall be conlel planes a distance t apart and parallel tained between two planes 0.01 apart and to the datum surface. parallel to the datum surface B.
Perpendicularity tolerance of a line with reference to a datum surface The tolerance zone when projected in a plane is limited by two parallel straight lines a distance t apart and perpendicular to the datum plane if the tolerance is specified only in one direction. The toleranced axis of the cylinder, to which the tolerance frame is connected, shall be contained between two parallel planes 0.1 apart, perpendicular to the datum surface.
Figure 57 Parallelism tolerance of a surface with reference to a datum line
Figure 58
The tolerance zone is limited by two paral- The toleranced surface shall be contained lel planes a distance t apart and parallel between two planes 0.1 apart and parallel to to the datum line. the datum axis C of the hole.
Figure 66 The tolerance zone is limited by a parallelepiped of section t1 t2 and perpendicular to the datum surface if the tolerance is specified in two directions perpendicular to each other.
Figure 67 The toleranced axis of the cylinder shall be contained in a parallelepipedic tolerance zone of 0.1 0.2 which is perpendicular to the datum surface.
Figure 59
Figure 60
Parallelism tolerance of a surface with reference to a datum surface The tolerance zone is limited by two parallel planes a distance t apart and parallel to the datum surface. The toleranced surface shall be contained between two parallel planes 0.01 apart and parallel to the datum surface D (figure 62). Figure 69 The toleranced axis of the cylinder to which the tolerance frame is connected shall be contained in a cylindrical zone of diameter 0.01 perpendicular to the datum surface A.
Figure 68 The tolerance zone is limited by a cylinder of diameter t perpendicular to the datum surface if the tolerance value is preceded by the sign .
Figure 62 Figure 61
Figure 63
All the points of the toleranced surface in a length of 100, placed anywhere on this surface, shall be contained between two parallel planes 0.01 apart and parallel to the datum surface A (figure 63).
Figure 70
Figure 71
32
33
Symbol
Symbol
Definition of the tolerance zone 5.13.8 Positional tolerance Positional tolerance of a line The tolerance zone when projected in a plane is limited by two parallel straight lines a distance t apart and disposed symmetrically with respect to the theoretically exact position of the considered line if the tolerance is specified only in one direction.
Perpendicularity tolerance of a surface with reference to a datum line The tolerance zone is limited by two The toleranced face of the workpiece shall parallel planes a distance t apart and be contained between two parallel planes perpendicular to the datum line. 0.08 apart and perpendicular to the axis A (datum line).
Each of the toleranced lines shall be contained between two parallel straight lines 0.05 apart which are symmetrically disposed about the theoretically exact position of the considered line, with reference to the surface A (datum surface).
Figure 72
Figure 73
Perpendicularity tolerance of a surface with reference to a datum surface The tolerance zone is limited by two The toleranced surface shall be contained parallel planes a distance t apart and between two parallel planes 0.08 apart and perpendicular to the horizontal datum surperpendicular to the datum surface. face A. Figure 81 Figure 80 The axis of the hole shall be contained within a cylindrical zone of diameter 0.08 the axis of which is in the theoretically exact position of the considered line, with reference to the surfaces A and B (datum surfaces).
Figure 74 5.13.7 Angularity tolerance Angularity tolerance of a line with reference to a datum line Line and datum line in the same plane. The tolerance zone when projected in a plane is limited by two parallel straight lines a distance t apart and inclined at the specified angle to the datum line.
Figure 75 The tolerance zone is limited by a cylinder Figure 83 of diameter t the axis of which is in the theoretically exact position of the Each of the axes of the eight holes shall be considered line if the tolerance value is contained within a cylindrical zone of diameter 0.1 the axis of which is in the theoretically preceded by the sign . exact position of the considered hole, with reference to the surfaces A and B (datum surfaces).
The toleranced axis of the hole shall be contained between two parallel straight lines 0.08 apart which are inclined at 60 to the horizontal axis A-B (datum line).
Figure 82 Figure 84 Figure 76 Figure 77 Positional tolerance of a flat surface or a median plane The tolerance zone is limited by two parallel planes a distance t apart and disposed symmetrically with respect to the theoretically exact position of the considered surface. The inclined surface shall be contained between two parallel planes which are 0.05 apart and which are symmetrically disposed with respect to the theoretically exact position of the considered surface with reference to the datum surface A and the axis of the datum cylinder B (datum line).
Angularity tolerance of a surface with reference to a datum surface The tolerance zone is limited by two paral- The toleranced surface shall be contained lel planes a distance t apart and inclined between two parallel planes 0.08 apart which at the specified angle to the datum are inclined at 40 to the datum surface A. surface.
Figure 78
Figure 79
Figure 85
Figure 86
34
35
Symbol
Symbol
Definition of the tolerance zone Symmetry tolerance of a line or an axis The tolerance zone is limited by a parallelepiped of section t1 . t2, the axis of which coincides with the datum axis if the tolerance is specified in two directions perpendicular to each other.
5.13.9 Concentricity and coaxiality tolerance Concentricity tolerance of a point The tolerance zone is limited by a circle of The centre of the circle, to which the tolerdiameter t the centre of which coincides ance frame is connected, shall be contained with the datum point. in a circle of diameter 0.01 concentric with the centre of the datum circle A.
The axis of the hole shall be contained in a parallelepipedic zone of width 0.1 in the horizontal and 0.05 in the vertical direction and the axis of which coincides with the datum axis formed by the intersection of the two median planes of the datum slots A-B and C-D.
Figure 87 Coaxiality tolerance of an axis The tolerance zone is limited by a cylinder of diameter t, the axis of which coincides with the datum axis if the tolerance value is preceded by the sign .
Figure 88 Figure 95 The axis of the cylinder, to which the tolerance frame is connected, shall be contained in a cylindrical zone of diameter 0.08 coaxial with the datum axis A-B. 5.13.11 Circular runout tolerance Circular runout tolerance - radial The tolerance zone is limited within any The radial runout shall not be greater than plane of measurement perpendicular to 0.1 in any plane of measurement during one the axis by two concentric circles a revolution about the datum axis A-B. distance t apart, the centre of which coincides with the datum axis.
Toleranced surface
Figure 96
Figure 89 5.13.10 Symmetry tolerance Symmetry tolerance of a median plane The tolerance zone is limited by two parallel planes a distance t apart and disposed symmetrically to the median plane with respect to the datum axis or datum plane.
Figure 90
Figure 98
Plane of measurement
The median plane of the slot shall be contained between two parallel planes, which are 0.08 apart and symmetrically disposed about the median plane with respect to the datum feature A.
The radial runout shall not be greater than 0.2 in any plane of measurement when measuring the toleranced part of a revolution about the centre line of hole A (datum axis). Figure 97
Runout normally applies to complete revolutions about the axis but could be limited to apply to a part of a revolution.
Figure 91 Symmetry tolerance of a line or an axis The tolerance zone when projected in a plane is limited by two parallel straight lines a distance t apart and disposed symmetrically with respect to the datum axis (or datum plane) if the tolerance is specified only in one direction.
Figure 92 Circular runout tolerance - axial The axis of the hole shall be contained between two parallel planes which are 0.08 apart and symmetrically disposed with respect to the actual common median plane of the datum slots A and B.
Figure 99
Figure 100
The tolerance zone is limited at any radial The axial runout shall not be greater than 0.1 position by two circles a distance t apart at any position of measurement during one lying in a cylinder of measurement, the revolution about the datum axis D. axis of which coincides with the datum axis.
Cylinder of measurement
Figure 102 Figure 93 Figure 94 Figure 101
36
37
Technical Drawings Sheet Sizes, Title Block, Non-standard Formats

Indication and interpretation Technical drawings [extract from DIN 476 (10.76) and DIN 6671 Part 6 (04.88)] 6. Sheet sizes The DIN 6771 standard Part 6 applies to the preTable 3 Trimmed sheet Sheet sizes acc. to DIN 476, A series axb A0 Figure 104 A1 594 x 841 420 x 594 297 x 420 210 x 297 584 x 831 410 x 584 287 x 410 200 x 287 625 x 880 450 x 625 330 x 450 240 x 330 The runout in the direction perpendicular to the tangent of a curved surface shall not be greater than 0.1 in any cone of measurement during one revolution about the datum axis C. 841 x 1189 Drawing area 1) a1 x b1 831 x 1179 a2 x b2 880 x 1230 Untrimmed sheet sentation of drawing forms even if they are created by CAD. This standard may also be used for other technical documents. The sheet sizes listed below have been taken from DIN 476 and DIN 6771 Part 6.
Symbol
Definition of the tolerance zone Circular runout tolerance in any direction The tolerance zone is limited within any cone of measurement, the axis of which coincides with the datum axis by two circles a distance t apart. Unless otherwise specified the measuring direction is normal to the surface.
Cone of measurement
The runout in the direction indicated by the arrow shall not be greater than 0.1 in any cone of measurement during one revolution about the datum axis C.
Figure 103
A2 A3 A4
1) The actually available drawing area is reduced by the title block, the filing margin, the possible sectioning margin, etc. Figure 105 Circular runout tolerance in a specified direction The tolerance zone is limited within any cone of measurement of the specified angle, the axis of which coincides with the datum axis by two circles a distance t apart. The runout in the specified direction shall not be greater than 0.1 in any cone of measurement during one revolution about the datum axis C. Drawing area
6.1 Title block Formats w A3 are produced in broadside. The title block area is in the bottom right corner of the trimmed sheet. For the A4 format the title block area is at the bottom of the short side (upright format).
Trimmed drawing sheet
Figure 106
Title block
6.2 Non-standard formats Non-standard formats should be avoided. When necessary they should be created using the
dimensions of the short side of an A-format with the long side of a greater A-format.
38
39
Technical Drawings Drawings Suitable for Microfilming

7. General In order to obtain perfect microfilm prints the following recommendations should be adhered to: 7.1 Indian ink drawings and CAD drawings show the best contrasts and should be preferred for this reason. 7.2 Pencil drawings should be made in special cases only, for example for drafts. Recommendation: 2H-lead pencils for visible edges, letters and dimensions; 3H-lead pencils for hatching, dimension lines and hidden edges. 9. Type sizes Table 4: Type sizes for drawing formats (h = type height, b = line width) Paper sizes Application range g for lettering g h Type, drawing no. Texts and nominal dimensions Tolerances, roughness values, symbols 10 5 3.5 A0 and A1 b 1 0.5 0.35 A2, A3 and A4 h 7 3.5 2.5 b 0.7 0.35 0.25 8. Lettering For the lettering - especially with stencil - the vertical style standard lettering has to be used acc. to DIN 6776 Part 1, lettering style B, vertical (ISO 3098). In case of manual lettering the vertical style or sloping style standard lettering may be used according to DIN 6776 Part 1, lettering style B (ISO 3098). 8.1 The minimum space between two lines in a drawing as well as for lettering should be at least once, but better twice the width of a line in order to avoid merging of letters and lines in case of reductions.
Technical Drawings Drawings Suitable for Microfilming

10.1 Line groups 0.5 and 0.7 with the pertaining line width according to table 5 may only be used. Assignment to the drawing formats A1 and A0 is prescribed. For the A4, A3 and A2 formats, line group 0.7 may be used as well. 12. Lettering examples for stenciling and handwritten entries 12.1 Example for formats A4 to A2 11. Indian ink fountain pen The use of the type sizes according to table 4 and the lines according to table 5 permits a restricted number of 5 different fountain pens (line widths 0.25; 0.35; 0.5; 0.7; 1 mm).
9.1 The type sizes as assigned to the paper sizes in table 4 must be adhered to with regard to their application range. Larger type heights are 10. Lines according to DIN 15 Part 1 and Part 2 Table 5: Line groups, line types and line widths Line group Drawing format Line type Solid line (thick) Solid line (thin) Short dashes (thin) Dot-dash line (thick) Dot-dash line (thin) Dash/double-dot line (thin) Freehand (thin)
also permissible. Type heights smaller by approx. 20% will be accepted if this is required in a drawing because of restricted circumstances.
0.5 A4, A3, A2 Line width 0.5 0.25 0.25 0.5 0.25 0.25 0.25
0.7 A1, A0
0.7 0.35 0.35 0.7 0.35 0.35 0.35
40
41
Standardization ISO Metric Screw Threads (Coarse Pitch Threads)

Page 43 44 45 46
Bolt
Standardization ISO Metric Screw Threads (Coarse Pitch Threads) ISO Metric Screw Threads (Coarse and Fine Pitch Threads) Cylindrical Shaft Ends ISO Tolerance Zones, Allowances, Fit Tolerances; Inside Dimensions (Holes) ISO Tolerance Zones, Allowances, Fit Tolerances; Outside Dimensions (Shafts) Parallel Keys, Taper Keys, and Centre Holes
ISO metric screw threads (coarse pitch threads) following DIN 13 Part 1, 12.86 edition
Nut
D1 d2 d3 H H1 h3 R
Bolt thread diameter
d + 2 H1 D2 d + 0.64952 P d + 1.22687 P 0.86603 P 0.54127 P 0.61343 P H 6 0.14434 P
47 48
Nut thread diameter
Diameters of series 1 should be preferred to those of series 2, and these again to those of series 3. Nominal thread diameter d=D
Series 1 Series 2 Series 3 3 3.5 4 4.5 5 6 7 8 9 10 11 12 14 16 18 20 22 24 27 30 33 36 39 42 45 48 52 56 60 64 68
Pitch P
mm 0.5 0.6 0.7 0.75 0.8 1 1 1.25 1.25 1.5 1.5 1.75 2 2 2.5 2.5 2.5 3 3 3.5 3.5 4 4 4.5 4.5 5 5 5.5 5.5 6 6
Pitch diameter d2 = D2
mm 2.675 3.110 3.545 4.013 4.480 5.350 6.350 7.188 8.188 9.026 10.026 10.863 12.701 14.701 16.376 18.376 20.376 22.051 25.051 27.727 30.727 33.402 36.402 39.077 42.077 44.752 48.752 52.428 56.428 60.103 64.103
Core diameter d3
mm 2.387 2.764 3.141 3.580 4.019 4.773 5.773 6.466 7.466 8.160 9.160 9.853 11.546 13.546 14.933 16.933 18.933 20.319 23.319 25.706 28.706 31.093 34.093 36.479 39.479 41.866 45.866 49.252 53.252 56.639 60.639
Depth of thread h3
mm 0.307 0.368 0.429 0.460 0.491 0.613 0.613 0.767 0.767 0.920 0.920 1.074 1.227 1.227 1.534 1.534 1.534 1.840 1.840 2.147 2.147 2.454 2.454 2.760 2.760 3.067 3.067 3.374 3.374 3.681 3.681
Round R
mm 0.072 0.087 0.101 0.108 0.115 0.144 0.144 0.180 0.180 0.217 0.217 0.253 0.289 0.289 0.361 0.361 0.361 0.433 0.433 0.505 0.505 0.577 0.577 0.650 0.650 0.722 0.722 0.794 0.794 0.866 0.866
D1
mm 2.459 2.850 3.242 3.688 4.134 4.917 5.917 6.647 7.647 8.376 9.376 10.106 11.835 13.835 15.294 17.294 19.294 20.752 23.752 26.211 29.211 31.670 34.670 37.129 40.129 42.587 46.587 50.046 54.046 57.505 61.505
H1
mm 0.271 0.325 0.379 0.406 0.433 0.541 0.541 0.677 0.677 0.812 0.812 0.947 1.083 1.083 1.353 1.353 1.353 1.624 1.624 1.894 1.894 2.165 2.165 2.436 2.436 2.706 2.706 2.977 2.977 3.248 3.248
2
Tensile stress crosssection As 1)

mm2 5.03 6.78 8.78 11.3 14.2 20.1 28.9 36.6 48.1 58.0 72.3 84.3 115 157 193 245 303 353 459 561 694 817 976 1121 1306 1473 1758 2030 2362 2676 3055
1) The tensile stress cross-section is calculated acc. to DIN 13 Part 28 with formula
As
p 4
d2 ) d3 2
42
43
Standardization ISO Metric Screw Threads (Coarse and Fine Pitch Threads)
Selection of nominal thread diameters and pitches for coarse and fine pitch threads from 1 mm to 68 mm diameter, following DIN 13 Part 12, 10.88 edition Nominal thread diameter d=D Series Series 1 2 1 1.2 1.4 1.6 1.8 2 2.2 2.5 3 3.5 4 5 6 8 10 12 14 16 18 20 22 24 Coarse itch pitch Series thread 3 0.25 0.25 0.3 0.35 0.35 0.4 0.45 0.45 0.5 0.6 0.7 0.8 1 1.25 1.5 1.75 2 15 2 17 2.5 2.5 2.5 3 25 26 3 28 3.5 32 3.5 35 4 38 4 40 4.5 4.5 5 50 5 55 5.5 58 5.5 6 65 6 Pitches P for fine pitch threads 4 3 2 1.5 1.25 1 0.75 0.5
Standardization Cylindrical Shaft Ends
Cylindrical shaft ends Acc. to DIN 748/1, 1.70 edition

Diameter ISO Series toler1 2
zone
Cylindrical shaft ends Acc. to DIN 748/1, 1.70 edition

Diameter ISO Series toler1 2
zone
FLENDER works standard W 0470, 5.82 edition

ISO
FLENDER works standard W 0470, 5.82 edition

ISO
tolerDiaLength ance ance meter Long Short zone
Length
tolerDiaLength ance ance meter Long Short zone
Length
mm mm 6 7 8 9
mm 16 16 20 20 23 23 30 30 40 40 50 50 50 60 60 80 80 80 80 110 110 110 110 110 110 140 140 m6 140 140 170 170 170 170
mm
mm
mm
mm mm 100 110 120 130 140 150 160 170
mm 210 210 210 250 250 250 300 300 300 350 350 350
mm 165 165 165 200 200 200 240 240 240 280 280 280 330 330 330 380 380 380 450 450 450 540 540 540 540 540 540 540 680 680 680 680
mm 100 110 120 130 140 150 160 170 180 190 200 220 240 250 260 280 300 320 340 360 380 400 420 440 450 460 480 500
mm m6 180
210 240 270
1.5 1.5 1.5 1.5 2 2 2 2 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.25 1.25 1.25
1 1 1 1 1 1 1 1 1 1 1
0.75 0.75 0.75
0.5 0.5 0.5 0.5
10 11 12 14 16 19 20 22 24 25 28 30 32 35 38 40 42 45 48 50 55 60 65 70 75 80 85 90 95
15 15 18 18 28 28 36 36 36 42 42 58 58 58 58 82 82 82 82 82 82 105 105 105 105 130 130 130 130 14 16 19 20 22 24 25 28 30 32 35 38 40 42 45 48 50 55 60 65 70 75 80 85 90 95 30
180 190 200
310
35
k6
220 350 240 250 260 410 410 410 470 m6 300 470 470 550 550 550 650 650 650 650 650 650 650 800 800 800 800
k6
40 50
400 n6
280
450 500 550 590
27 30 33 36 39 42 45 48 52 56 60 64 68
2 2 2 3 3 3 3 3 3 4 4 4 4 3 3 3 3 2 2 2 2 2 2 2 2 2 2 2 2
60
320 340
70
360 380
80 m6 90 105 120
400 420 440 450 460 480 500
650 690 750
790
140
560
530 600 630
160
44
45
Standardization ISO Tolerance Zones, Allowances, Fit Tolerances Inside Dimensions (Holes)
ISO tolerance zones, allowances, fit tolerances; Inside dimensions (holes) acc. to DIN 7157, 1.66 edition; DIN ISO 286 Part 2, 11.90 edition
m + 500 + 400 + 300 + 200 + 100 0 100 200 300 400 500 ISO Series 1 abbrev. Series 2 from to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to 1 3 3 6 6 10 10 14 14 18 18 24 24 30 30 40 40 50 50 65 65 80 80 100 100 120 120 140 140 160 160 180 180 200 200 225 225 250 250 280 280 315 315 355 355 400 400 450 450 500 H7 P7 6 16 8 20 9 24 11 29 N7 4 14 4 16 4 19 5 23 N9 4 29 0 30 0 36 0 43 M7 2 12 0 12 0 15 0 18 K7 0 10 + 3 9 + 5 10 + 6 12 J6 + + + 2 4 5 3 5 4 J7 + + + 4 6 6 6 8 7 +10 0 +12 0 +15 0 +18 0 +14 0 +18 0 +22 0 +27 0 H8 H11 + 60 0 + 75 0 + 90 0 +110 0 G7 +12 + 2 +16 4 +20 + 5 +24 + 6 + + + + + + 20 6 28 10 35 13 + + + + + + 39 14 50 20 61 25 F8 E9 D9 + + + + + + 45 20 60 30 76 40 + + + + + + 60 20 78 30 98 40 +120 + 60 +145 + 70 +170 + 80 D10 C11
Standardization ISO Tolerance Zones, Allowances, Fit Tolerances Outside Dimensions (Shafts)
ISO tolerance zones, allowances, fit tolerances; Outside dimensions (shafts) acc. to DIN 7157, 1.66 edition; DIN ISO 286 Part 2, 11.90 edition
m + 500
Tolerance zones shown for nominal dimension 60 mm
+ 400 + 300 + 200 + 100 0 100 200 300 400 500 ISO abbrev. from to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to above to ISO abbrev. Series 1 x8/u8 Series 2 1) 1 + 34 3 + 20 3 + 46 6 + 28 6 + 56 10 + 34 10 + 67 14 + 40 14 + 72 18 + 45 18 + 87 24 + 54 24 + 81 30 + 48 30 + 99 40 + 60 40 +109 50 + 70 50 +133 65 + 87 65 +148 80 +102 80 +178 100 +124 100 +198 120 +144 120 +233 140 +170 140 +253 160 +190 160 +273 180 +210 180 +308 200 +236 200 +330 225 +258 225 +356 250 +284 250 +396 280 +315 280 +431 315 +350 315 +479 355 +390 355 +524 400 +435 400 +587 450 +490 450 +637 500 +540 Series 1 x8/u8 Series 2 1) r6 s6 + 20 + 14 + 27 + 19 + 32 + 23 r5 + 14 + 10 + 20 + 15 + 25 + 19 + + + + + + 16 10 23 15 28 19 n6 +10 + 4 +16 + 8 +19 +10 m5 + 6 + 2 + 9 + 4 +12 + 6 m6 + 8 + 2 +12 + 4 +15 + 6 k5 + 4 0 + 6 + 1 + 7 + 1 k6 + 6 0 + 9 + 1 +10 + 1
Tolerance zones shown for nominal dimension 60 mm
A11 +330 +270 +345 +270 +370 +280 +400 +290
j6 + 4 2 + 6 2 + 7 2
h6 h9 js6 h7 h8 h11 + 3 0 0 0 0 0 3 6 10 14 25 60 + 4 0 0 0 0 0 4 8 12 18 30 75 +4.5 0 0 0 0 0 4.5 9 15 22 36 90
f7 g6 2 8 4 12 5 14 6 16 10 22 13 28 e8 14 28 20 38 25 47 d9 20 45 30 60 40 76 c11 60 120 70 145 80 170 a11 270 330 270 345 280 370
+ 6 5
+10 8
+ 43 + 75 + 93 +120 +205 + 16 + 32 + 50 + 50 + 95
+ 39 + 31 + 34 +23 +15 +18 + 9 +12 + 8 +5.5 0 0 0 0 0 6 16 32 50 95 290 + 28 + 23 + 23 +12 + 7 + 7 + 1 + 1 3 5.5 11 18 27 43 110 17 34 59 93 205 400
14 35
7 28
0 52
0 21
+ 6 15
+ 8 5
+12 9
+21 0
+33 0
+130 0
+28 + 7
+ 53 + 92 +117 +149 +240 + 20 + 40 + 65 + 65 +110 +280 + 64 +112 +142 +180 +120 + 25 + 50 + 80 + 80 +290 +130 +330 + 76 +134 +174 +220 +140 + 30 + 60 +100 +100 +340 +150 +390 + 90 +159 +207 +260 +170 + 36 + 72 +120 +120 +400 +180 +450 +200 +106 +185 +245 +305 +460 + 43 + 85 +145 +145 +210 +480 +230 +530 +240 +122 +215 +285 +355 +550 + 50 +100 +170 +170 +260 +570 +280 +620 +137 +240 +320 +400 +300 + 56 +110 +190 +190 +650 +330 +720 +151 +265 +350 +440 +360 + 62 +125 +210 +210 +760 +400 +840 +165 +290 +385 +480 +440 + 68 +135 +230 +230 +880 +480 F8 E9 D9 D10 C11
+430 +300 +470 +310 +480 +320 +530 +340 +550 +360 +600 +380 +630 +410 +710 +460 +770 +520 +830 +580 +950 +660 +1030 + 740 +1110 + 820 +1240 + 920 +1370 +1050 +1560 +1200 +1710 +1350 +1900 +1500 +2050 +1650 A11
+ 48 + 37 + 41 +28 +17 +21 +11 +15 + 9 +6.5 0 0 0 0 0 7 20 40 65 110 300 + 35 + 28 + 28 +15 + 8 + 8 + 2 + 2 4 6.5 13 21 33 52 130 20 41 73 117 240 430 120 310 0 0 0 0 0 9 25 50 80 280 470 16 25 39 62 160 25 50 89 142 130 320 290 480 140 340 0 0 0 0 0 10 30 60 100 330 530 19 30 46 74 190 29 60 106 174 150 360 340 550 170 380 0 0 0 0 0 12 36 72 120 390 600 22 35 54 87 220 34 71 126 207 180 410 400 630 200 460 450 710 0 0 0 0 0 14 43 85 145 210 520 25 40 40 63 63 100 100 250 250 39 39 83 148 148 245 245 460 770 25 230 580 480 830 240 660 530 950 0 0 0 0 0 15 50 100 170 260 740 29 46 46 72 72 115 115 290 290 44 44 96 172 172 285 285 550 1030 29 280 820 570 1100 300 920 0 0 0 0 0 17 56 110 190 620 1240 32 52 81 130 320 49 108 191 320 330 1050 650 1370 360 1200 0 0 0 0 0 18 62 125 210 720 1560 36 57 89 140 360 54 119 214 350 400 1350 760 1710 440 1500 0 20 68 135 230 840 1900 0 0 0 0 40 63 97 155 400 60 131 232 385 480 1650 880 2050 h6 h9 f7 h7 h8 h11 g6 e8 d9 c11 a11
17 42
8 33
0 62
0 25
+ 7 18
+10 6
+14 11
+25 0
+39 0
+160 0
+34 + 9
+ 59 + 45 + 50 +33 +20 +25 +13 +18 +11 + 43 + 34 + 34 +17 + 9 + 9 + 2 + 2 5 + 72 + 53 + 78 + 59 + 93 + 71 +101 + 79 +117 + 92 +125 +100 +133 +108 +151 +122 +159 +130 +169 +140 +190 +158 +202 +170 +226 +190 +244 +208 +272 +232 +292 +252 s6 + 54 + 41 + 56 + 43 + 66 + 51 + 69 + 54 + 81 + 63 + 83 + 65 + 86 + 68 + 97 + 77 +100 + 80 +104 + 84 +117 + 94 +121 + 98 +133 +108 +139 +114 +153 +126 +159 +132 r5 + 60 + 41 + 62 + 43 + 73 + 51 + 76 + 54 + 88 + 63 + 90 + 65 + 93 + 68 +106 + 77 +109 + 80 +113 + 84 +126 + 94 +130 + 98 +144 +108 +150 +114 +166 +126 +172 +132 r6
+8 8
Nominal dimensions in mm
Nominal dimensions in mm
21 51
9 39
0 74
0 30
+ 9 21
+13 6
+18 12
+30 0
+46 0
+190 0
+40 +10
+39 +24 +30 +15 +21 +12 +9.5 +20 +11 +11 + 2 + 2 7 9.5
24 59
10 45
0 87
0 35
+10 25
+16 6
+22 13
+35 0
+54 0
+220 0
+47 +12
+45 +28 +35 +18 +25 +13 +11 +23 +13 +13 + 3 + 3 9 11
28 68 68
12 52 52
0 100 100
0 40 40
+12 28 28
+18 7
+26 14 14
+40 0
+63 0
+250 0
+54 +14
+52 +33 +40 +21 +28 +14 +12.5 +27 +15 +15 + 3 + 3 11 11 12.5 12.5
33 79 79
14 60 60
0 115 115
0 46 46
+13 33 33
+22 7
+30 16 16
+46 0
+72 0
+290 0
+61 +15
+60 +37 +46 +24 +33 +16 +14.5 +31 +17 +17 + 4 + 4 13 13 14.5 14.5
36 88
14 66
0 130
0 52
+16 36
+25 7
+36 16
+52 0
+81 0
+320 0
+69 +17
+66 +43 +52 +27 +36 +16 +16 +34 +20 +20 + 4 + 4 16 16
41 98
16 73
0 140
0 57
+17 40
+29 7
+39 18
+57 0
+89 0
+360 0
+75 +18
+73 +46 +57 +29 +40 +18 +18 +37 +21 +21 + 4 + 4 18 18
45 108
17 80
0 155
0 63
+18 45
+33 7
+43 20
+63 0 H7
+97 0 H8
+400 0
+83 +20
+80 +50 +63 +32 +45 +20 +20 +40 +23 +23 + 5 + 5 20 20 n6 m5 m6 k5 k6 j6 js6
ISO Series 1 abbrev. Series 2
P7
N7
N9
M7
K7
J6
J7
H11
G7
1) Up to nominal dimension 24 mm: x8; above nominal dimension 24 mm: u8
46
47
Standardization Parallel Keys, Taper Keys, and Centre Holes

Dimensions of parallel keys and taper keys
Depth of keyDiameter Width Height way in shaft d b h t1 above to
1) 2)
Parallel keys y and taper p keys y acc to DIN 6885 Part 1, acc. 1 6886 and 6887
Editions: 08.68 12.67 4.68
Physics Internationally Determined Prefixes Basic SI Units Derived SI Units Legal Units Outside the SI Physical Quantities and Units of Lengths and Their Powers Physical Quantities and Units of Time Physical Quantities and Units of Mechanics Physical Quantities and Units of Thermodynamics and Heat Transfer Physical Quantities and Units of Electrical Engineering Physical Quantities and Units of Lighting Engineering Different Measuring Units of Temperature Measures of Length and Square Measures Cubic Measures and Weights Energy, Work, Quantity of Heat Power, Energy Flow, Heat Flow Pressure and Tension Velocity Equations for Linear Motion and Rotary Motion
Page 50 50 51 51 52 53 53/55 55/56 56 57 57 58 59 59 60 60 60 61
Depth of keyway in hub t2 DIN 6885/1 6886/ 6887

2)
Lengths, see below l1 DIN 6885/1 6886 l
Side fitting square and rectangular keys
mm mm mm 6 8 2 8 10 3 10 12 4 12 17 5 17 22 6 22 30 8 30 38 10 38 44 12 44 50 14 50 58 16 58 65 18 65 75 20 75 85 22 85 95 25 95 110 28 110 130 32 130 150 36 150 170 40 170 200 45 200 230 50 230 260 56 260 290 63 290 330 70 330 380 80 380 440 90 440 500 100 Lengths mm I1 or I
mm mm mm 2 1.2 1.0 3 1.8 1.4 4 2.5 1.8 5 3 2.3 6 3.5 2.8 7 4 3.3 8 5 3.3 8 5 3.3 9 5.5 3.8 10 6 4.3 11 7 4.4 12 7.5 4.9 14 9 5.4 14 9 5.4 16 10 6.4 18 11 7.4 20 12 8.4 22 13 9.4 25 15 10.4 28 17 11.4 32 20 12.4 32 20 12.4 36 22 14.4 40 25 15.4 45 28 17.4 50 31 19.5 6 8 10 12 14 90 100 110 125
from to from to mm mm mm mm mm Parallel key and keyway acc. to DIN 6885 Part 1 0.5 6 20 6 20 0.9 6 36 8 36 1.2 8 45 10 45 Square and rectangular taper keys 1.7 10 56 12 56 2.2 14 70 16 70 2.4 18 90 20 90 2.4 22 110 25 110 2.4 28 140 32 140 2.9 36 160 40 160 3.4 45 180 45 180 3.4 50 200 50 200 Taper and round-ended sunk key y and 3.9 56 220 56 220 k keyway acc. to t DIN 6886 4.4 63 250 63 250 4.4 70 280 70 280 ) The tolerance zone for hub keyway y y width b for 5.4 80 320 80 320 1) parallel keys with normal fit is ISO JS9 and 6.4 90 360 90 360 with close fit ISO P9. The tolerance zone for 7.1 100 400 100 400 shaft keyway width b with normal fit is ISO N9 8.1 110 400 110 400 and with close fit ISO P9. P9 9.1 125 400 125 400 10.1 140 400 140 400 2) Dimension h of the taper key names the largest height g g of the key, y, and dimension tz the 11.1 160 400 keyway The shaft largest depth of the hub keyway. 11.1 180 400 keyway and hub keyway dimensions 13.1 200 400 Lengths according to DIN 6887 - taper keys with gib not 14.1 220 400 deterhead - are equal to those of DIN 6886 6886. 16.1 250 400 mined 18.1 280 400 16 18 20 22 25 28 32 36 40 45 50 56 63 70 80 140 160 180 200 220 250 280 320 360 400 Centre holes i shaft in h f ends d (centerings) ( i ) acc. to DIN 332 P Part 1
Dimensions of 60 centre holes

Recommended Bore diameters diameter d 2) d1 a 1) above to mm mm mm mm 6 10 1.6 5.5 10 25 2 6.6 2.5 8.3 25 63 3.15 10 4 12.7 63 100 5 15.6 6.3 20 Recommended diameters d6 2) d1 d2 d3 3) above to mm mm mm mm mm 7 10 M3 2.5 3.2 10 13 M4 3.3 4.3 13 16 M5 4.2 5.3 16 21 M6 5 6.4 21 24 M8 6.8 8.4 24 30 M10 8.5 10.5 30 38 M12 10.2 13 38 50 M16 14 17 50 85 M20 17.5 21 85 130 M24 21 25 130 225 M30* 26 31 225 320 M36* 31.5 37 320 500 M42* 37 43 Form B b mm 0.5 0.6 0.8 0.9 1.2 1.6 1.4 d2 mm 3.35 4.25 5.3 6.7 8.5 10.6 13.2 d3 mm 5 6.3 8 10 12.5 16 18 Minimum dimensions t mm 3.4 4.3 5.4 6.8 8.6 10.8 12.9
Form B DIN 332/1 4.80
Form DS d4 mm 5.3 6.7 8.1 9.6 12.2 14.9 18.1 23 28.4 34.2 44 55 65 d5 mm 5.8 7.4 8.8 10.5 13.2 16.3 19.8 25.3 31.3 38 48 60 71 t1 +2 mm 9 10 12.5 16 19 22 28 36 42 50 60 74 84 t2 min. mm 12 14 17 21 25 30 37 45 53 63 77 93 105 t3 +1 mm 2.6 3.2 4 5 6 7.5 9.5 12 15 18 17 22 26 t4 mm 1.8 2.1 2.4 2.8 3.3 3.8 4.4 5.2 6.4 8 11 15 19 t5 mm 0.2 0.3 0.3 0.4 0.4 0.6 0.7 1.0 1.3 1.6 1.9 2.3 2.7
Keyway
Form DS (with thread) DIN 332/1 5.83
1) 2) ) * 3)
Cutting-off dimension in case of no centering Diameter applies to finished workpiece Dimensions not acc acc. to DIN 332 Part 2 Drill diameter for tapping-size holes acc. to DIN 336 Part 1
48
49
Physics Internationally Determined Prefixes Basic SI Units

Internationally determined prefixes Decimal multiples and sub-multiples of units are represented with prefixes and symbols. Prefixes and symbols are used only in combination with unit names and unit symbols. Factor by which the unit is multiplied 1018 1015 1012 109 106 103 102 101 Prefix Atto Femto Pico Nano Micro Milli Centi Deci Symbol a f p n m c d Factor by which the unit is multiplied 101 102 103 106 109 1012 1015 1018 Prefix Deka Hecto Kilo Mega Giga Tera Peta Exa Symbol da h k M G T
Physics Derived SI Units Legal Units Outside the SI

Derived SI units having special names and special unit symbols SI unit Physical quantity Name Plane angle Solid angle Frequency, cycles per second Force Pressure, mechanical stress Energy; work; quantity of heat Power, heat flow P E Electric charge Electric potential Electric capacitance Electric resistance Electric conductance Celsius temperature Inductance Radian Steradian Hertz Newton Pascal Joule Watt Coulomb Volt Farad Ohm Siemens degrees Celsius Henry Symbol rad sr Hz N Pa J W C V F S C H 1 rad = 1 m/m 1 sr = 1 m2/m2 1 Hz = 1 s1 1 N = 1 kg . m/s2 1 Pa = 1 N/m2 = 1 kg/ (m . s2) 1 J = 1 N . m = 1 W . s = 1 kg . m2/m2 1 W = 1 J/s = 1 kg . m2/s3 1C=1A. s 1 V = 1 J/C = 1 (kg . m2)/(A . s3) 1 F = 1 C/V = 1 (A2 . s4)/(kg . m2) 1 = 1 V/A = 1 (kg . m2)/A2 . s3) 1 S = 1 1 = 1 (A2 . s3)/(kg . m2) 1 C = 1 K 1 H = 1 V . s/A Relation
Prefix symbols and unit symbols are written When giving sizes by using prefix symbols and without blanks and together they form the unit symbols, the prefixes should be chosen in symbol for a new unit. An exponent on the unit such a way that the numerical values are symbol also applies to the prefix symbol. between 0.1 and 1000. Example: 1 cm3 = 1 . (102m)3 = 1 . 106m3 1 s = 1 . 106s 106s1 = 106Hz = 1 MHz Example: 12 kN 3.94 mm 1.401 kPa 31 ns 1.2 104N 0.00394 m 1401 Pa 3.1 . 108s
instead of instead of instead of instead of
Prefixes are not used with the basic SI unit kilo- Combinations of prefixes and the following gram (kg) but with the unit gram (g). units are not allowed: Units of angularity: degree, minute, second Example: Units of time: minute, hour, year, day Milligram (mg), NOT microkilogram (kg). Unit of temperature: degree Celsius Basic SI units Basic SI unit Physical quantity Name Length Mass Time Electric current Metre Kilogram Second Ampere Symbol m kg s A Thermodynamic temperature Amount of substance Luminous intensity Kelvin K Physical quantity Name Symbol Basic SI unit
Legal units outside the SI Physical quantity Unit name Round angle Gon Degree Minute Second Litre Minute Hour Day Year Ton Bar Unit symbol 1) gon 2) 2) 2) l min h d a t bar 2) 2) 2) 2) Definition 1 perigon = 2 rad 1 gon = (/200)rad 1 = (/180)rad 1 = (1/60) 1 = (1/60) 1 l = 1 dm3 = (1/1000) m3 1 min = 60 s 1 h = 60 min = 3600 s 1 d = 24 h = 86 400 s 1 a = 365 d = 8 760 h 1 t = 103 kg = 1 Mg 1 bar = 105 Pa
Plane angle
Volume
Time
Mass Mole Candela mol cd Pressure
1) A symbol for the round angle has not yet been internationally determined 2) Do not use with prefixes
50
51
Physics Physical Quantities and Units of Lengths and Their Powers

Physical quantities and units of lengths and their powers Symbol Physical quantity SI unit Symbol Name m (metre) N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Basic unit L.U.: m; mm; cm; dm; km; etc. N.A.: micron (): 1 = 1 m ngstrm unit (): 1 = 1010 m L.U.: mm2; cm2; dm2; km2 are (a): 1 a = 102 m2 hectare (ha): 1 ha = 104 m2 L.U.: mm3; cm3; dm3 litre (l): 1 l = dm3 N.: moment of a force; moment of resistance L.U.: mm3; cm3 N.: formerly: geometrical moment of inertia L.U.: mm4; cm4 N. : 1 rad ) 1 m (arc) 1m ) ) 1m m 1 m (radius) 1m
Physics Physical Quantities and Units of Time and of Mechanics

Physical quantities and units of time Symbol Physical quantity SI unit Symbol Name N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Basic unit L.U.: ns; s; ms; ks Minute (min): 1 min = 60 s Hour (h): 1 h = 60 min Day (d): 1 d = 24 h Year (a): 1 a = 365 d (Do not use prefixes for decimal multiples and sub-multiples of min, h, d, a) L.U.: kHz; MHz; GHz; THz Hertz (Hz): 1 Hz = 1/s N.: Reciprocal value of the duration of one revolution L.U.: min1 = 1/min L.U.: cm/s; m/h; km/s; km/h 1 km h ) 1 m s 3.6 N.: Time-related velocity L.U.: cm/s2 N.: Gravity varies locally. Normal gravity (gn): gn = 9.80665 m/s2 9.81 m/s2
Length
Time, Period, Duration
s (second)
Area
m2 (square metre) m3 (cubic metre) m3 m4
V H
Volume Moment of area Second moment of area
Frequency, Periodic frequency Rotational frequency (speed) Velocity Acceleration, linear Gravity Angular velocity Angular acceleration Volume flow rate
Hz (Hertz) s1
v a g
m/s m/s2 m/s2 rad/s rad/s2 m3/s
1 rad
1 degree ) 1 o ) p rad 180

90 o ) p rad 2
L.U.: rad/min L.U.: /s2 L.U.: l/s; l/min; dm3/s; l/h; m3/h; etc.
L.U. : mrad, mrad ,. Plane angle rad (radian) Degree ( o) : 1 o ) p rad 180 o Minute ( ) : 1 ) 1 60 Second ( ) : 1 ) 1 60 Gon (gon) : 1 gon ) p rad 200 N.A. : Right angle +(L) : 1L ) p rad 2 Centesimal degree (g) : 1g ) 1 gon Centesimal minute ( c) : 1 c ) 1 gon 100 c cc cc Centesimal second ( ) : 1 ) 1 100 , Solid angle sr (steradian)
N. : 1 sr ) 1 m 2 (spherical surface) 1 m 2 (square of spherical radius)
2 ) 1 m2 m
Physical quantities and units of mechanics Symbol Physical quantity Mass SI unit Symbol Name kg (kilogram) N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Basic unit L.U.: g; mg; g; Mg ton (t): 1 t = 1000 kg N.: m = m/l L.U.: mg/m; g/km; In the textile industry: Tex (tex):1 tex = 10-6 kg/m = 1 g/km N.: m = m/A L.U.: g/mm2; g/m2; t/m2 N.: r = m/V L.U.: g/cm3, kg/dm3, Mg/m3, t/m3, kg/l 1g/cm3 = 1 kg/dm3 = 1 Mg/m3 = 1 t/m3 = 1 kg/l
Mass per unit length Mass in relation to the surface Density
kg/m
kg/m2
kg/m3
52
53
Physics Physical Quantities and Units of Mechanics

Physical quantities and units of mechanics (continued) Symbol Physical quantity Mass moment of inertia; second mass moment Rate of mass flow Force Weight Torque Bending moment SI unit Symbol Name kg . m2 N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Instead of the former flywheel effect GD2 2 GD 2 in kpm 2 now : J ) GD 4 L.U.: g m2; t m2 L.U.: kg/h; t/h L.U.: N; mN; kN; MN; etc.; 1 N = 1 kg m/s2 N.A.: kp (1 kp = 9.80665 N) N.: Weight = mass acceleration due to gravity L.U.: kN; MN; GN; etc. L.U.: Nm; mNm; kNm; MNm; etc. N.A.: kpm; pcm; pmm; etc. L.U.: Nmm; Ncm; kNm etc. N.A.: kpm; kpcm; kpmm etc. N.: 1 Pa = 1 N/m2 L.U.: Bar (bar): 1 bar = 100 000 Pa = 105 Pa bar, mbar N.A.: kp/cm2; at; ata; at; mmWS; mmHg; Torr 1kp/cm2 = 1 at = 0.980665 bar 1 atm = 101 325 Pa = 1.01325 bar 1 Torr ) 101325 Pa ) 133.322 Pa 760 1 mWS = 9806.65 Pa = 9806.65 N/m2 1 mmHg = 133.322 Pa = 133.322 N/m2
Physics Physical Quantities and Units of Mechanics, Thermodynamics and Heat Transfer
Physical quantities and units of mechanics (continued) Symbol Physical quantity SI unit Symbol Name N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: 1 W = 1 J/s = 1 Nm/s L.U.: W; mW; kW; MW; etc. kJ/s; kJ/h; MJ/h, etc. N.A.: PS PS; k kpm/s; m/s kcal/h 1 PS = 735.49875 W 1 kpm/s = 9.81 W 1 kcal/h = 1.16 W 1 hp = 745.70 W N.: 1 Pa . s = 1 Ns/m2 L.U.: dPa . s, mPa . s N.A.: Poise (P): 1 P = 0.1 Pa . s L.U.: mm2/s; cm2/s N.A.: Stokes (St): 1 St = 1/10000 m2/s 1cSt = 1 mm2/s
.Power
W Watt) Heat flow
m F G M, T Mb
kg/s N (Newton) N (Newton) Nm Nm
Dynamic viscosity Kinematic viscosity
Pa . s
m2/s
Physical quantities and units of thermodynamics and heat transfer Symbol Physical quantity Thermodynamic temperature Celsius temperature Heat Quantity of heat SI unit Symbol Name K (Kelvin) N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Basic unit 273.15 K = 0 C 373.15 K = 100 C L.U.: mK N.: t C The degrees Celsius (C) is a special name for the degrees Kelvin (K) when stating Celsius temperatures. The temperature interval of 1 K equals that of 1 C.
Pressure
Pa (Pascal)
pabs pamb
Absolute pressure Ambient atmospheric pressure Pressure above atmospheric Direct stress (tensile and compressive stress) Shearing stress Extension Work
Pa (Pascal) Pa (Pascal) Pa (Pascal)
1 J = 1 Nm = 1 Ws L.U.: mJ; kJ; MJ; GJ; TJ N.A.: cal; kcal

a) m+ cp
pe
pe = pabs - pamb a L.U.: N/mm2 1 N/mm2 = 106 N/m2 H
Temperature conductivity
m2/s
[ W/(m . K)] = thermal conductivity m [kg/m3] = density of the body cp [J/(kg K)] = specific heat capacity at constant pressure
N/m2
W, A E, W
N/m2 m/m
L.U.: N/mm2 N.: l / l L.U.: m/m; cm/m; mm/m N.: 1 J = 1 Nm = 1 Ws L.U.: mJ; kJ; MJ; GJ; TJ; kWh 3 6 MJ 1 kWh = 3.6 N.A.: kpm; cal; kcal 1 cal = 4.1868 J; 860 kcal = 1 kWh s ,h
Enthalpy (Heat content) Entropy Heat transfer coefficient
N.: J
Quantity of heat absorbed under certain conditions L.U.: kJ; MJ; etc. N.A.: kcal; Mcal; etc.
J/K
1 J/K = 1 Ws/K = 1 Nm/K L.U.: kJ/K N.A.: kcal/deg; kcal/K L.U.: W/(cm2 . K); kJ/(m2 . h . K) N.A.: cal/(cm2 . s . grd) kal/(m2 . h . grd) 4.2 kJ/(m2 . h . K)
J (Joule) Energy
W/(m2 . K)
54
55
Physics Physical Quantities and Units of Thermodynamics, Heat Transfer and Electrical Engineering
Physical quantities and units of thermodynamics and heat transfer (continued) Symbol Physical quantity Specific heat capacity Coefficient of linear thermal expansion Coefficient of volumetric expansion SI unit Symbol Name J/(K . kg) N.: Note L.U.: Further legal units N.A.: Units no longer allowed 1 J/(K . kg) = W . s / (kg . K) N.: Heat capacity referred to mass N.A.: cal / (g . deg); kcal / (kg . deg); etc. m / (m . K) = K1 N.: Temperature unit/length unit ratio L.U.: m / (m . K); cm / (m . K); mm / (m . K) m3 / (m3 . K) = K1 N.: Temperature unit/volume ratio N.A.: m3 / (m3 . deg)
Physics Physical Quantities and Units of Lighting Engineering, Different Measuring Units of Temperature
Physical quantities and units of lighting engineering Symbol Physical quantity Luminous intensity Luminous density; Luminance Luminous flux Illuminance SI unit Symbol Name cd (Candela) N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Basic unit 1 cd = 1 lm (lumen)/sr (Steradian) L.U.: mcd; kcd L.U.: cd / cm2; mcd/m2; etc. 1 2 N.A.: Apostilb (asb); 1 asb p cd m Nit (nt): 1 nt = 1 cd / m2 Stilb (sb): 1 sb = 104 cd / m2 1 Im = 1 cd . sr L.U.: klm 1 lx = 1 lm / m2
K1
cd /
m2
v,
K1
lm (Lumen) lx (Lux)
Physical quantities and units of electrical engineering Symbol I Physical quantity Current strength Electriccharge; Quantity of electricity Electric voltage Electric resistance Electric conductance Electrostatic capacitance SI unit Symbol Name A (Ampere) C (Coloumb) V (Volt) (Ohm) S (Siemens) F (Farad) N.: Note L.U.: Further legal units N.A.: Units no longer allowed N.: Basic unit L.U.: pA; nA; A; mA; kA; etc. 1C=1A.s 1 Ah = 3600 As L.U.: pC; nC; C; kC 1 V = 1 W / A = 1 J / (s . A) = 1 A . = 1 N . m / (s . A) L.U.: V; mV; kV; MV; etc. 1 = 1 V / A = 1 W / A2 1 J / (s . A2) = 1 N . m / (s . A2) L.U.: ; m; k; etc. Reciprocal of electric resistance 1 S = 1 1 = 1 / ; G = 1 / R L.U.: S; mS; kS 1F=1C/V=1A.s/V = 1 A2 . s / W = 1 A 2 . s2 / J = 1 A2 . s2/ (N . m) L.U.: pF; F; etc. N.: TK TK TK Kelvin K TK 273.15 ) t c 255.38 ) 5 9 5 9 TR tF
Different measuring units of temperature Degrees Celsius C tC tC tC tC T K + 273.15 5 t + 32 9 F 5 T + 273.15 9 R Degrees Fahrenheit F tF tF tF tF 9 5 T K + 459.67 32 ) 9 5 tC Degrees Rankine R TR TR TR TR 9 5 TK
9 t ) 273.15 5 c 459.67 ) t F
T R + 459.67
Comparison of some temperatures 0.00 + 255.37 + 273.15 + 273.16 + 373.15 273.15 17.78 0.00 + 0.01 + 100.00 459.67 0.00 + 32.00 + 32.02 + 212.00 0.00 + 459.67 + 491.67 + 491.69 + 671.67
1)
1)
1) The triple point of water is +0.01 C. The triple point of pure water is the equilibrium point between pure ice, air-free water and water vapour (at 1013.25 hPa). Temperature comparison of F with C
56
57
Physics Measures of Length and Square Measures

Measures of length
Unit 1 in 1 ft 1 yd 1 stat mile 1 naut mile 1 mm 1m 1 km = = = = = = = = Inch in 1 12 36 63 360 72 960 0.03937 39.37 39 370 Foot ft 0.08333 1 3 5280 6080 3.281 . 103 3.281 3281 Yard yd 0.02778 0.3333 1 1760 2027 1.094 . 103 1.094 1094 Stat mile Naut mile 1 1.152 0.6214 0.8684 1 0.5396 mm 25.4 304.8 914.4 1 1000 106 m 0.0254 0.3048 0.9144 1609.3 1853.2 0.001 1 1000 km 1.609 1.853 106 0.001 1
Physics Cubic Measures and Weights; Energy, Work, Quantity of Heat

Cubic measures
Unit 1 cu in 1 cu ft 1 cu yd 1 US liquid quart 1 US gallon 1 imp quart 1 imp gallon 1 cm3 1 dm3 (l) 1 m3 = = = = = = = = = cu in 1 1728 46656 57.75 231 69.36 277.4 0.06102 61.02 61023 cu ft 1 27 0.03342 0.1337 0.04014 0.1605 0.03531 35.31 US liquid US Imp quart quart gallon 0.01732 0.01442 29.92 7.481 24.92 807.9 202 672.8 1 0.25 0.8326 4 1 3.331 1.201 0.3002 1 4.804 1.201 4 1.057 0.2642 0.88 1057 264.2 880 Imp gallon 6.229 168.2 0.2082 0.8326 0.25 1 0.22 220 cm3 16.39 946.4 3785 1136 4546 1 1000 106 dm3 (l) 0.01639 28.32 764.6 0.9464 3.785 1.136 4.546 0.001 1 1000 m3 0.02832 0.7646 106 0.001 1
1 German statute mile = 7500 m 1 geograph. mile = 7420.4 m = 4 arc minutes at the equator (1 at the equator = 111.307 km) 1 internat. nautical mile 1 German nautical mile (sm) 1 mille marin (French)
=1852 m = 1 arc minute at the degree of longitude (1 at the meridian = 111.121 km)
Astronomical units of measure 1 light-second = 300 000 km 1 l.y. (light-year) = 9.46 .1012 km 1 parsec (parallax second, distances to the stars) = 3.26 l.y. 1 astronomical unit (mean distance of the earth from the sun) = 1.496 .108 km Typographical unit of measure: 1 point (p) = 0.376 mm
Other measures of length of the Imperial system 1 micro-in = 106 in = 0.0254 m 1 mil = 1 thou = 0.001 in = 0.0254 mm 1 line = 0.1 in = 2,54 mm 1 fathom = 2 yd = 1.829 m 1 engineers chain = 100 eng link = 100 ft = 30.48 m 1 rod = 1 perch = 1 pole = 25 surv link = 5.029 m 1 surveyors chain = 100 surv link = 20.12 m 1 furlong = 1000 surv link = 201.2 m 1 stat league = 3 stat miles = 4.828 km
Other measures of length of the metric system France: 1 toise = 1.949 m 1 myriametre = 10 000 m Russia: 1 werschok = 44.45 mm 1 saschen = 2.1336 m 1 arschin = 0.7112 m 1 werst = 1.0668 km Japan: 1 shaku = 0.3030 m 1 ken = 1.818 m 1 ri = 3.927 km
1 US minim = 0.0616 cm3 (USA) 1 US fl dram = 60 minims = 3.696 cm3 1 US fl oz = 8 fl drams = 0,02957 l 1 US gill = 4 fl oz = 0.1183 l 1 US liquid pint = 4 gills = 0.4732 l 1 US liquid quart = 2 liquid pints = 0.9464 l 1 US gallon = 4 liquid quarts = 3.785 l 1 US dry pint = 0.5506 l 1 US dry quart = 2 dry pints = 1.101 l 1 US peck = 8 dry quarts = 8.811 l 1 US bushel = 4 pecks = 35.24 l 1 US liquid barrel = 31.5 gallons = 119.2 l 1 US barrel = 42 gallons = 158.8 l (for crude oil) 1 US cord = 128 cu ft = 3.625 m2
1 Imp minim = 0.0592 cm3 (GB) 1 Imp ft drachm = 60 minims = 3.552 cm3 1 Imp ft oz = 8 ft drachm = 0,02841 l 1 Imp gill = 5 ft oz = 0.142 l 1 Imp pint = 4 gills = 0.5682 l 1 Imp quart = 2 pints = 1.1365 l 1 imp gallon = 4 quarts = 4.5461 l 1 iImp pottle = 2 quarts = 2.273 l 1 Imp peck = 4 pottles = 9.092 l 1 Imp bushel = 4 pecks = 36.37 l 1 Imp quarter = 8 bushels = 64 gallons = 290.94 l
Weights
Unit dram oz lb short cwt long cwt short long ton ton g kg t
Square measures
Unit 1 square inch 1 square foot 1 square yard 1 square mile 1 cm2 1 dm2 1 m2 1a 1 ha 1 km2 = = = = = = = = = = sq in 1 144 1296 0.155 15.5 1550 sq ft 1 9 0.1076 10.76 1076 sq yd 0.1111 1 0.01196 1.196 119.6 sq mile 1 0.3861 cm2 6.452 929 8361 1 100 10000 dm2 0.06452 9.29 83.61 0.01 1 100 10000 m2 0.0929 0.8361 0.01 1 100 10000 a 0.01 1 100 10000 ha 259 0.01 1 100 km2 2.59 0.01 1
1 dram = 1 0.0625 0.003906 1.772 0.00177 1 oz (ounze) = 16 1 0.0625 28.35 0.02835 1 lb (pound) = 256 16 1 0.01 0.008929 453.6 0.4536 1 short cwt (US) = 25600 1600 100 1 0.8929 0.05 0.04464 45359 45.36 0.04536 1 long cwt (GB/US) = 28672 1792 112 1.12 1 0.056 0.05 50802 50.8 0.0508 1 short ton (US) = 32000 2000 20 17.87 1 0.8929 907.2 0.9072 1 long ton (GB/US) = 35840 2240 22.4 20 1.12 1 1016 1.016 1g = 0.5643 0.03527 0.002205 1 0.001 106 1kg = 564.3 35.27 2.205 0.02205 0.01968 1000 1 0.001 1t = 35270 2205 22.05 19.68 1.102 0.9842 106 1000 1 1 grain = 1 / 7000 lb = 0.0648 g (GB) 1 solotnik = 96 dol = 4.2659 g (CIS) 1 stone = 14 lb = 6.35 kg (GB) 1 lot = 3 solotnik = 12.7978 g (CIS) 1 short quarter = 1/4 short cwt = 11.34 kg (USA) 1 funt = 32 lot = 0.409 kg (CIS) 1 pud = 40 funt = 16.38 kg (CIS) 1 long quarter = 1/4 long cwt = 12.7 kg (GB / USA) 1 berkowetz = 163.8 kg (CIS) 1 quintal or 1 cental = 100 lb = 45.36 kg (USA) 1 kwan = 100 tael = 1000 momme = 10000 fun = 1 quintal = 100 livres = 48.95 kg (F) 3.75 kg (J) (J) 1 kilopound = 1kp = 1000 lb = 453.6 kg (USA) 1 hyaku kin = 1 picul = 16 kwan = 60 kg (J)
tdw = tons dead weight = lading capacity of a cargo vessel (cargo + ballast + fuel + stores), mostly given in long tons, i.e. 1 tdw = 1016 kg
Other square measures of the Imperial system 1 sq mil = 1 S 106 sq in = 0.0006452 mm2 1 sq line = 0.01 sq in = 6.452 mm2 1 sq surveyors link = 0.04047 m2 1 sq rod = 1 sq perch = 1 sq pole = 625 sq surv link = 25.29 m2 1 sq chain = 16 sq rod = 4.047 a 1 acre = 4 rood = 40.47 a 1 township (US) = 36 sq miles = 3.24 km2 p 1 circular in + sq in + 5.067cm 2(circular area with 1 in dia.) 4 p 1 circular mil + sq mil + 0.0005067mm2 (circular area with 1 mil dia.) 4
Other square measures of the metric system
Energy, work, quantity of heat

Work
1 ft lb 1 erg 1 Joule (WS) 1 kpm 1 PSh 1 hph 1 kWh 1 kcal 1 Btu
Russia:
1 kwadr. archin 1 kwadr. saschen 1 dessjatine 1 kwadr. werst = 0.5058 m2 = 4.5522 m2 = 1.0925 ha = 1.138 km2 = 3.306 m2 = 0.9917a = 15.42 km2
ft lb
= 1 = 0.7376 . 107 = 0.7376 = 7.233 = 1.953 . 106 = 1.98 . 106 = 2.655 . 106 = 3.087 . 103 = 778.6
erg
J = Nm = Ws
kpm
PSh
hph
0.505 . 106 37.25 . 1015 372.5 . 109 3.653 . 106 0.9863 1 1.341 1.559 . 103 392.9 . 106
kWh
0.3768 . 106 27.78 . 1015 277.8 . 109 2.725 . 106 0.7355 0.7457 1 1.163 . 103 293 . 106
kcal
0.324 . 103 23.9 . 1012 238 . 106 2.344 . 103 632.5 641.3 860 1 0.252
Btu
1.286 . 103 94.84 . 1012 948.4 . 106 9.301 . 103 2510 2545 3413 3.968 1
Japan:
1 tsubo 1 se 1 ho-ri
1.356 . 107 1.356 0.1383 0.5121 . 106 107 0.102 . 107 37.77 . 1015 1 107 1 0.102 377.7 . 109 9.807 1 9.807 . 107 3.704 . 106 12 6 3 . . . 270 10 26.48 10 2.648 10 1 1.014 26.85 . 1012 2.685 . 106 273.8 . 103 1.36 36 . 1012 3.6 . 106 367.1 . 103 1.581 . 103 41.87 . 109 4186.8 426.9 1055 107.6 10.55 . 109 398.4 . 106
1 in oz = 0.072 kpcm; 1 in lb = 0.0833ft lb = 0.113 Nm, 1 thermi (French) = 4.1855 . 106 J; 1 therm (English) = 105.51 . 106 J Common in case of piston engines: 1 litre-atmosphere (litre . atmosphere ) = 98.067 J
58
59
Physics Power, Energy Flow, Heat Flow, Pressure and Tension, Velocity
Power, energy flow, heat flow
Power 1 erg/s 1W 1kpm/s 1 PS (ch) 2) 1hp 1 kW 1 kcal/s 1 Btu/s = = = = = = = = erg/s 1 107 9.807 . 107 7.355 . 109 7.457 . 109 1010 41.87 . 108 10.55 . 109 W kpm/s PS hp kW kcal/s Btu/s 107 0.102 . 107 0.136 . 109 0.1341 . 109 1010 23.9 . 1012 94.84 . 1012 1 0.102 1.36 . 103 1.341 . 103 103 239 . 106 948.4 . 106 9.807 1 13.33 . 103 13.15 . 103 9.804 . 103 2.344 . 103 9.296 . 103 735.5 75 1 0.9863 0.7355 0.1758 0.6972 745.7 76.04 1.014 1 0.7457 0.1782 0.7068 1000 102 1.36 1.341 1 0.239 0.9484 4187 426.9 5.692 5.614 4.187 1 3.968 1055 107.6 1.434 1.415 1.055 0.252 1
Physics Equations for Linear Motion and Rotary Motion

SI Sym Symunit bol Basic formulae Linear motion
distance moved divided by time
Definition
Uniform motion Velocity Angular velocity Angle of rotation Distance moved
atm
Rotary motion
angular velocity = angle of rotation in radian measure/time
m/s rad/s rad m/s m
v r v s
v+
s2 ) s1 t2 ) t1
s + const. t
p +
r2 ) r1 t2 ) t1
r t
+ const.
motion accelerated from rest:
1 poncelet (French) = 980.665 W; flywheel effect: 1 kgm2 = 3418 lb in 2
v+s t s=v.t
acceleration equals change of velocity divided by time
r+
r t
Pressure and tension

Unit 1 b=daN = 1mbar=cN/cm2 = 1 bar = daN/cm2 = 1 WS at 4 C 1 p/cm2 kp/m2=1mm mbar bar = = cN/ dN/m2 cm2 1 1000 106 0.001 1 1000 bar = daN/ cm2 kp/m2 Torr= kp/cm2 kp/mm2 mm mm p/cm2 = at WS QS 1.02 1020 0.1 1 1000 105 1.02 0.0001 0.001 1 100 0.7501
angle of rotation = . t angular acceleration equals change of angular velocity divided by time
lb sq ft
lb sq in
long ton {sh ton} sq in
sq in

Uniformly accelerated motion Acceleration Angular acceleration
0.0102 0.001 10.2 1 10197 1 10
2.089 0.0145 14.5
m/s2 rad/s2 m/s2
a a v v s
a+
v2 ) v1 t2 ) t1
v + const. t
m+
p2)p1 t2 ) t1
p t
+ const.
0.0102 750.1 0.9869 2089 0.01 1 0.7356 0.2048
0.0064 0.0072 0.635
motion accelerated from rest:
= 98.07
= 980.7 0.9807 1333
2.048 0.0142 14.22 1422
v2 2s a+v+ + t 2s t2 v+a t+ 2 a s
p2 2r m+p + + 2 t t 2r p +m v+r p +r t+m 2 t m t
1 kp/cm2=1at = (techn. atmosph.) 1 kp/mm2 =
Velocity
980.7 0.9807 10000 98067 98.07 106 735.6 0.9678 2048 73556 96.78 1 0.7112
m/s m/s m
Circumferential speed Distance moved Uniform motion and constant force or constant torque Work
1 Torr = 1 mm = QS at 0 C 1 atm (pressure of the atmosphere) 1 lb/sq ft
1.333 0.00133 13.6
1.36 0.00136
2.785 0.01934
s+v 2
t+a 2
2 t2 + v 2a
r +p 2
angle of rotation
2 t2 + p 2m
1013
1.013 10332
1033
1.033
760
2116
14.7
force . distance moved
torque . angle of rotation in radian measure
= 478.8 0.4788
4.882 0.4882
1.575 1.406
0.3591 51.71
0.068 152.4 136.1
1 144
1 2240 2000
1 0.8929
0.0005 1.12 1
W=F.s
work in unit of time = force . velocity
1 lb/sq in=1 psi = 68948 68.95 0.0689 703.1 1 long ton/sq = in (GB) 1 short ton/sq = in (US) 154.4 137.9
70.31 0.0703 157.5 140.6
W=M.
work in unit of time = torque . angular velocity
Power Non-uniform (accelerated) motion Force In case of any motion Energy
P+W+F t
P+W+M t
1 psi = 0.00689 N / mm2 1 N/m2 (Newton/m2) = 10 b, 1 barye (French) = 1 b, 1 piece (pz) (French) = 1 sn/m2 102 kp/m2. 1 hpz = 100 pz = 1.02 kp/m2. In the USA, inches Hg are calculated from the top, i.e. 0 inches Hg = 760 mm QS and 29.92 inches Hg = 0 mm QS = absolute vacuum. The specific gravity of mercury is assumed to be 13.595 kg/dm 3.
accelerating force = mass . acceleration
accel. torque = second mass moment . angular acceleration
F *)
F=m.a * *) m 2 v2
M=J.
J J N
Ek Ep FF
Ek
Ek + J 2
weight . height
p2
Velocity
Unit m/s m/min km/h ft/min mile/h = = = = = m/s 1 0.0167 0.278 0.0051 0.447 m/min 60 1 16.67 0.305 26.82 km/h 3.6 0.06 1 0.0183 1.609 ft/min 196.72 3.279 54.645 1 87.92 mile/h 2.237 0.0373 0.622 0.0114 1
Potential energy (due to force of gravity) Centrifugal force
Ep = G . h = m . g . h FF = m . rs . 2 (rs = centre-of-gravity radius)
*) Momentum (kinetic energy) equals half the mass . second power of velocity. **) Kinetic energy due to rotation equals half the mass moment of inertia . second power of the angular velocity.
60
61
Mathematics/Geometry Calculation of Areas
Mathematics / Geometry Calculation of Areas Calculation of Volumes
Page 63 64 Square
A = area
A = a2 a d A
U = circumference Polygon
A a A1 ) A2 ) A3 h1 ) b h2 ) b h3 2
a 2
Rectangle
A d a b
Formed area
A r 2 (2 3 + m) 2 0.16 r2
a2 ) b2
Parallelogram
A a h
Circle
A
d2 m 4 0.785 d2 d
r2
A h Circular ring
2rm
Trapezium
A m h
m 4
(D 2 + d 2) m
(d ) b) b m {a ) b} 2 b {D + d} 2 r2 m
o
Triangle
A a {a 2 {2 h A} h}
Circular sector
A
360 o {b r} 2 o} {r m b 180 o
Equilateral triangle
A a2 3 4 a 3 2
Circular segment
r 2 { o m} + sin 2 180 1 [ r(b + s) ) sh] 2
s h
2 r sin
Hexagon
3 A d s 2 3 a a a2 2 3
2 a r (1 + cos ) 2 { o m} 180 r ^ {D d m} a 4 {D ) d} m 2 m (a ) b) [ 1 )
2
s tan 2 4
Ellipse
A U
Octagon
A d s
2a 2( 2 ) 1) a 4)2 a( 2 ) 1) 2
1 {a + b} 4 {a ) b}
{a + b} ) 1 64 {a ) b}
6
{a + b} ) 1 256 {a ) b}
.. ]
62
63
Mathematics / Geometry Calculation of Volumes
V = volume Cube
V O d a3 6 a2
O = surface
M = generated surface Frustum of cone

V M {p h} ( D 2 ) Dd ) d 2 ) 12 {p m} (D)d) 2 2p p h {D + d} 2
2
Mechanics / Strength of Materials Axial Section Moduli and Axial Second Moments of Area (Moments of Inertia) of Different Profiles Deflections in Beams Values for Circular Sections Stresses on Structural Members and Fatigue Strength of Structures
Page 66 67 68 69
a 3
) h2
Parallelepiped
V O d a b c 2 (ab ) ac ) bc ) a2 ) b2 ) c2
Sphere
V
4 r3 p 3 4.189
1 6 r3 p
d 3p
4p
r2
d2
Rectangular block
V A h
Spherical zone
V M {p 6 2 r h} (3a 2 ) 3b 2 ) h 2) p h
(Cavalier principle)
Pyramid
V {A 3 h}
Spherical segment
{p
h} 3 2 s ) h2 4 p h2 r + h 3 6 2 r p h p ( s 2 ) 4h 2 ) 4
Frustum of pyramid
V h (A ) A ) A 2 1 3 1 h A1 ) A2 2 A 2)
Spherical sector
V O 2 3 {p 2 h r} r2 p
(4h ) s)
Cylinder
V M O
d2 p h 4 2 2 r r p p h (r ) h)
Cylindrical ring
V O D p2 4 d d2
p2
Hollow cylinder
V {h 4 p} (D 2 + d 2 )
Cylindrical barrel
V {h p} ( 2D 2 ) d 2 ) 12
Cone
V M O m
r2 r r p p
p 3
h m ( r ) m) d 2
2
Prismatoid
V h ( A ) A ) 4A ) 1 2 6
h2 )
64
65
Mechanics / Strength of Materials Axial Section Moduli and Axial Second Moments of Area (Moments of Inertia) of Different Profiles
Cross-sectional area
W1 W2
Mechanics / Strength of Materials Deflections in Beams
Section modulus
bh 2 6 hb 2 6
Second moment of area

1 2
bh 3 hb 3
12 12
f, fmax, fm, w, w1, w2 a, b, l, x1, x1max, x2 E q, qo
Deflection (mm) Lengths (mm) Modulus of elasticity (N/mm2) Line load (N/mm)
F 3
w(x)
, 1, 2, A, B, Angle () Forces (N) F, FA, FB Second moment of area (mm4) (moment of inertia)
F 3
f
{3E }
F
1+
3 x 1 x ) 2 2
{3E }
tan m
F 2 {2 E }
W1
W2
a3 6
a4
Fp
12
q 4
w(x)
{8E }
q
1+
4 x)1 x 3 3
4
f
q 4 {8E }
tan m
q 3 {6 E }
W1 W2
bh 2 24 for e hb 2 24
2 h 3
1 2
bh 3 hb 3
36 48
w(x)
5 qo 4 x) x 4+5 {120E } qo
qo 4 {30E }
tan m
qo 3 {24 E }
W1 W2 W1 for e
5 3 R 8
0.625 R 3
1 2
0.5413 R 3 6b 2 ) 6bb 1 ) b 2 1 12( 3b ) 2b 1 ) 1 3b ) 2b 1 h 3 2b ) b 1 h2
5 16
3 R4
0.5413 R 4
2 F 3 x
1+
w(x)
{16E }
F
4 x 3 l
2
x
F 3 2
f
{48 E }
tan m
F 2 {16 E }
6b 2 ) 6bb 1 ) b 2 1
1
36 (2b ) b1 )
h3
F 2 F 3 a b 2 x 1 x2 l+ 1 b ab x2 2 ab F 3
x
w (x )
1 1
{6E }
1)
2
tan m
{3E }
f 1) 2a b
W1
BH 3 + bh 3 6H
1
BH 3 + bh 3 12
x1max a (l ) b) 3a for a > b change a and b for a < b
F 3
w (x )
b a
2x 2
2 2
{6E } b F 3
F
1)
fmax
{ ) b} 3b
) b 3a
tan m
f 1) a 2b
a 2
f
w(x)
x
2
W1
W2
r D3
32
D3
{2E }
a
1+
1 x 3
F 3 {2E }
a l
2
1+
4 a 3
tan m
F 2 1 {2E } F 2 2 {2E }
1+
10
rD 4
64
D 4 20
F 3
w(x)
W1
W2
r 32
D4 + d4 D (r ) s 2) rsr 2
1 2
{2E }
x 2
x 1+ x + 1 a 3
2
fm
F 3 {8E }
1+
4 a 3
2
tan m
1+2
r ( D4 + d4 ) 64 rsr 3 1 ) (s 2r) 2
or in case of thin wall thickness s:

W1 W2
1 2
FA = FB = F
F 3
x
w (x )
1 1
rsr 3 W1 W2 r a 2b 4 r b 2a 4 r a 3b 4
x
{2E }
1 x1 3
3
+
1)
2 a x1 a 2 a ) 1) 3
tan m
F 2 a a 1) {2E } 3 2 F a 2 a 1) {2E } 3 1 F 2 2 {2E } a
1 2
F 3 2
w (x )
r b 3a 4 r 3 (a 1b 1 + a 3 2b 2 ) 4 2 (b + b2) thin r 2 a (a ) 3b) s 4
2 2
{2E }
x2 a x2 1+
F 3
fm
{8E }
tan m
FA = FB = F
F 3
w (x )
a x1
W1
1 a1
1 1
{6E } F 3 x2
1+
x1
2
x
F 3 1
f
2
1)
F 2
tan m
{3E }
{6E }
a l
or if the wall thickness is

s W1 W1 with e a1 + a2 b1 + b2 2 (a + a 2)
1
w (x )
2a
2 2
{6E } a q 4
F
x2 3a x 2 + a 3
2
x
F 3 2
a fmax
tan m
9 3E
tan m
B a
2 tan m
r a (a ) 3b) s 4
1 e
F 2 {6E }
tan m
F 1)
2)3
0.1908 r 3 0.5756 r
1
w(x)
r 1+ 4 {3r}
[r 8+8
(9 r) r 4
0.1098 r 4
F
{24E } q
1+2
2
)
5q 4
0 x fm
q 3 {24E }
{384E }
q 2
F
axis 1-1 = axis of centre of gravity
66
67
Mechanics / Strength of Materials Values for Circular Sections
Mechanics / Strength of Materials Stresses on Structural Members and Fatigue Strength of Structures
p 4 p 4 7, 85 p d2 l r d2 Diffusion of stress in structural members: loading types
Axial section modulus: Polar section modulus:
Wa Wp
a
Axial second moment of area (axial moment of inertia): Polar second moment of area (polar moment of area):
d mm 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 32. 34. 36. 38. 40. 42. 44. 46. 48. 50. 52. 54. 56. 58. 60. 62. 64. 66. 68. 70. 72. 74. 76. 78. 80. 82. 84. 86. 88. 90. 92. 95. 100. 105. 110. A cm2 0.293 0.385 0.503 0.636 0.785 0.950 1.131 1.327 1.539 1.767 2.011 2.270 2.545 2.835 3.142 3.464 3.801 4.155 4.524 4.909 5.309 5.726 6.158 6.605 7.069 8.042 9.079 10.179 11.341 12.566 13.854 15.205 16.619 18.096 19.635 21.237 22.902 24.630 26.421 28.274 30.191 32.170 34.212 36.317 38.485 40.715 43.008 45.365 47.784 50.265 52.810 55.418 58.088 60.821 63.617 66.476 70.882 78.540 86.590 95.033 Wa cm3 0.0212 0.0337 0.0503 0.0716 0.0982 0.1307 0.1696 0.2157 0.2694 0.3313 0.4021 0.4823 0.5726 0.6734 0.7854 0.9092 1.0454 1.1945 1.3572 1.5340 1.7255 1.9324 2.1551 2.3944 2.6507 3.2170 3.8587 4.5804 5.3870 6.2832 7.2736 8.3629 9.5559 10.8573 12.2718 13.9042 15.4590 17.2411 19.1551 21.2058 23.3978 25.7359 28.2249 30.8693 33.6739 36.6435 39.7828 43.0964 46.5890 50.2655 54.1304 58.1886 62.4447 66.9034 71.5694 76.4475 84.1726 98.1748 113.6496 130.6706 a cm4 0.0064 0.0118 0.0201 0.0322 0.0491 0.0719 0.1018 0.1402 0.1986 0.2485 0.3217 0.4100 0.5153 0.6397 0.7854 0.9547 1.1499 1.3737 1.6286 1.9175 2.2432 2.6087 3.0172 3.4719 3.9761 5.1472 6.5597 8.2448 10.2354 12.5664 15.2745 18.3984 21.9787 26.0576 30.6796 35.8908 41.7393 48.2750 55.5497 63.6173 72.5332 82.3550 93.1420 104.9556 117.8588 131.9167 147.1963 163.7662 181.6972 201.0619 221.9347 244.3920 268.5120 294.3748 322.0623 351.6586 399.8198 490.8739 596.6602 718.6884
p Mass /I kg/m 0.222 0.302 0.395 0.499 0.617 0.746 0.888 1.042 1.208 1.387 1.578 1.782 1.998 2.226 2.466 2.719 2.984 3.261 3.551 3.853 4.168 4.495 4.834 5.185 5.549 6.313 7.127 7.990 8.903 9.865 10.876 11.936 13.046 14.205 15.413 16.671 17.978 19.335 20.740 22.195 23.700 25.253 26.856 28.509 30.210 31.961 33.762 35.611 37.510 39.458 41.456 43.503 45.599 47.745 49.940 52.184 55.643 61.654 67.973 74.601
d3 32 p d3 16 p d4 64 p d4 32
J/I kgm2/m 0.000001 0.000002 0.000003 0.000005 0.000008 0.000011 0.000016 0.000022 0.000030 0.000039 0.000051 0.000064 0.000081 0.000100 0.000123 0.000150 0.000181 0.000216 0.000256 0.000301 0.000352 0.000410 0.000474 0.000545 0.000624 0.000808 0.001030 0.001294 0.001607 0.001973 0.002398 0.002889 0.003451 0.004091 0.004817 0.005635 0.006553 0.007579 0.008721 0.009988 0.011388 0.012930 0.014623 0.016478 0.018504 0.020711 0.023110 0.025711 0.028526 0.031567 0.034844 0.038370 0.042156 0.046217 0.050564 0.055210 0.062772 0.077067 0.093676 0.112834
Area: Mass: Density of steel:
A m r
Second mass moment of inertia (mass moment of inertia): J

d mm 115. 120. 125. 130. 135. 140. 145. 150. 155. 160. 165. 170. 175. 180. 185. 190. 195. 200. 210. 220. 230. 240. 250. 260. A cm2 103.869 113.097 122.718 132.732 143 139 153.938 165.130 176.715 188.692 201.062 213.825 226.980 240.528 254.469 268.803 283.529 298.648 314.159 346.361 380.133 415.476 452.389 490.874 530.929 Wa cm3 149.3116 169.6460 191.7476 215.6900 241.5468 269.3916 299.2981 331.3398 365.5906 402.1239 441.0133 482.3326 526.1554 572.5553 621.6058 673.3807 727.9537 785.3982 909.1965 1045.3650 1194.4924 1357.1680 1533.9808 1725.5198 1932.3740 2155.1326 2650.7188 3216.9909 3858.6612 4580.4421 5387.0460 6283.1853 7273.5724 8362.9196 9555.9364 10857.3442 12271.8463 13804.1581 15458.9920 17241.0605 19155.0758 21205.7504 23397.7967 25735.9270 28224.8538 30869.2894 33673.9462 36643.5367 39782.7731 43096.3680 46589.0336 50265.4824 54130.4268 58188.5791 62444.6517 66903.3571 71569.4076 76447.5155 81542.3934 86858.7536 92401.3084 98174.7703 a cm4 858.5414 1017.8760 1198.4225 1401.9848 1630.4406 1895.7410 2169.9109 2485.0489 2833.3269 3216.9909 3638.3601 4099.8275 4603.8598 5152.9973 5749.8539 6397.1171 7097.5481 7853.9816 9546.5638 11499.0145 13736.6629 16286.0163 19174.7598 22431.7569 26087.0491 30171.8558 39760.7820 51471.8540 65597.2399 82447.9575 102353.8739 125663.7060 152745.0200 183984.2320 219786.6072 260576.2608 306796.1572 358908.1107 417392.7849 482749.6930 555497.1978 636172.5116 725331.6994 823549.6636 931420.1743 1049555.8389 1178588.1176 1319167.3201 1471962.6056 1637661.9830 1816972.3105 2010619.2960 2219347.4971 2443920.3207 2685120.0234 2943747.7113 3220623.3401 3516585.7151 3832492.4910 4169220.1722 4527664.1126 4908738.5156
kg dm 3 d4 l r 32
J/I kgm2/m 0.134791 0.159807 0.188152 0.220112 0.255979 0.296061 0.340676 0.390153 0.444832 0.505068 0.571223 0.643673 0.722806 0.809021 0.902727 1.004347 1.114315 1.233075 1.498811 1.805345 2.156656 2.556905 3.010437 3.521786 4.095667 4.736981 6.242443 8.081081 10.298767 12.944329 16.069558 19.729202 23.980968 28.885524 34.506497 40.910473 48.166997 56.348573 65.530667 75.791702 87.213060 99.879084 113.877076 129.297297 146.232967 164.780267 185.038334 207.109269 231.098129 257.112931 285.264653 315.667229 348.437557 383.695490 421.563844 462.168391 505.637864 552.103957 601.701321 654.567567 710.843266 770.671947
Mass/ I kg/m 81.537 88.781 96.334 104.195 112.364 120.841 129.627 138.721 148.123 157.834 167.852 178.179 188.815 199.758 211.010 222.570 234.438 246.615 271.893 298.404 326.148 355.126 385.336 416.779 449.456 483.365 554.884 631.334 712.717 799.033 890.280 986.460 1087.572 1193.617 1304.593 1420.503 1541.344 1667.118 1797.824 1933.462 2074.032 2219.535 2369.970 2525.338 2685.638 2850.870 3021.034 3196.131 3376.160 3561.121 3751.015 3945.840 4145.599 4350.289 4559.912 4774.467 4993.954 5218.374 5447.726 5682.010 5921.227 6165.376
static Maximum stress limit: Mean stress: Minimum stress limit:
dynamic
o m u sch
sch
alternating o ) w 0 m w u +
o m u
oscillating m) a v (initial stress) m+ a
Ruling coefficient of strength of material for the calculation of structural members: Resistance to Fatigue strength under Fatigue strength under Resistance to breaking Rm fluctuating stresses Sch alternating stresses W deflection A Yield point Re; Rp0.2 Coefficients of fatigue strength D
Stress-number diagram
Stress Stress-number curve Damage curve Endurance limit Fatigue limit Fatigue strength under alternating stresses W Example: Tension-Compression Coefficient of fatigue strength
Fatigue strength diagram acc. to SMITH

Resistance to breaking Rm Yield point Re
Resistance to deflection A Fatigue strength under fluctuating stresses Sch Mean stress m
Number of cycles to failure N
270. 572.555 280. 615.752 300. 706.858 320. 804.248 340. 907.920 360. 1017.876 380. 400. 420. 440. 460. 480. 500. 520. 540. 560. 580. 600. 620. 640. 660. 680. 700. 720. 740. 760. 780. 800. 820. 840. 860. 880. 900. 920. 940. 960. 980. 1000. 1134.115 1256.637 1385.442 1520.531 1661.903 1809.557 1693.495 2123.717 2290.221 2463.009 2642.079 2827.433 3019.071 3216.991 3421.194 3631.681 3848.451 4071.504 4300.840 4536.460 4778.362 5026.548 5281.017 5541.769 5808.805 6082.123 6361.725 6647.610 6939.778 7238.229 7542.964 7853.982
In case of stresses below the damage curve initial damage will not occur to the material. Reduced stress on the member
v
Alternate area/Area of fluctuation
Permissible stress
perm.
Design strength of the member

D
bo S k
bd
with: D = ruling fatigue strength value of the material b = surface number ( 1) bd = size number ( 1) k = stress concentration factor ( 1) S = safety (1.2 ... 2)
Reduced stress v with: For the frequently occurring case of com = single axis bending stress bined bending and torsion, according to = torsional stress the distortion energy theory: 0 = constraint ratio according to Bach Alternating bending, dynamic torsion: 0 0.7 2 ) 3 (m o ) 2 v Alternating bending, alternating torsion: 0 1.0 Static bending, alternating torsion: 0 1.6
For bending and torsion Surface roughness Rt in m Surfaces with rolling skin Resistance to breaking of the material Rm
for tension compression bd = 1.0
Diameter of component d
68
69
Surface number bo
Size number bd
Hydraulics Hydrostatics
Hydraulics Hydrostatics (Source: K. Gieck, Technische Formelsammlung, 29th Edition, Gieck Verlag, D-7100 Heilbronn) Hydrodynamics (Source: K. Gieck, Technische Formelsammlung, 29th Edition, Gieck Verlag, D-7100 Heilbronn)
Page 71 p1 72 P2 po ) g h1 p 1 ) g (h 2 + h 1)
Pressure distribution in a fluid
p1 ) g
h
Linear pressure
Hydrostatic force of pressure on planes The hydrostatic force of pressure F is that force which is exerted on the wall by the fluid only i.e. without consideration of pressure p. F yD g g y s A cos p ms mx ys ) y sA y sA hs A ; xD mxy y sA m, mm
Hydrostatic force of pressure on curved surfaces The hydrostatic force of pressure on the curved surface 1, 2 is resolved into a horizontal component FH and a vertical component FV. FV is equal to the weight of the fluid having a volume V located (a) or thought to be located (b) over the surface 1, 2. The line of application runs through the centre of gravity. Fv g V (N, kN) FH is equal to the hydrostatic force of pressure on the projection of the considered surface 1, 2 on the plane perpendicular to FH. Buoyance The buoyant force FA is equal to the weight of the displaced fluids having densities and . g V)g V ( N, kN ) FA If the fluid with density is a gas, the following applies: FA For > = < g V ( N, kN )
k density of the body applies: k the body floats in k the body is suspended k the body sinks
a heavy liquid
S = centre of gravity of plane A D = centre of pressure x, s = moments of inertia xy = product of inertia of plane A referred to the x- and y-axes
70
71
Hydraulics Hydrodynamics
Discharge of liquids from vessels Vessel with bottom opening
Electrical Engineering Basic Formulae Speed, Power Rating and Efficiency of Electric Motors
Page 74 75 76 77 78 79 80
v
.
2 gH r A 2 gH Vessel with small lateral opening Types of Construction and Mounting Arrangements of Rotating Electrical Machinery Types of Protection for Electrical Equipment (Protection Against Contact and Foreign Bodies) Types of Protection for Electrical Equipment (Protection Against Water) Explosion Protection of Electrical Switchgear (Types of protection) Explosion Protection of Electrical Switchgear (Gases and vapours) Vessel with wide lateral opening
v s
.
2 gH 2 Hh (without any coefficient of friction) r A 2 gH

.
V F
Vv
2 r b 2 g (H 2 3
3 2
+ H1
3 2
Vessel with excess pressure on liquid level v

.
2 (gH ) A
) p
2 (gH )
Vessel with excess pressure on outlet v

.
2 A
p p
v: discharge velocity g: gravity : density p: excess pressure compared to external pressure : coefficient of friction (for water = 0.97) : coefficient of contraction ( = 0.62 for sharp-edged openings) ( = 0.97 for smooth-rounded openings) F: force of reaction . V : volume flow rate b: width of opening
72
73
Electrical Engineering Basic Formulae
Electrical Engineering Speed, Power Rating and Efficiency of Electric Motors

p Speed:
m mm 2 m
Ohms law: U R U R R U Material
Power rating: 60 p Output power 1) Direct current: . Pab = U . . Single-phase alternating current: Pab = U . . cos . r Three-phase current: Pab = 1.73 . U . . cos . r
m m mm 2
Series connection of resistors: R R1 ) R2 ) R3 ) ) Rn
Direct current
a) Metals Aluminium Bismuth R total resistance m Lead Rn individual resistance m Cadmium Iron wire Gold Shunt connection of resistors: Copper 1 ) 1 ) 1 ) ) 1 1 Magnesium Rn R1 R2 R3 R Nickel R total resistance m Platinum Mercury individual resistance m Rn Silver Tantalum Electric power: Tungsten Current consumption Zinc Power Tin P U b) Alloys Aldrey (AlMgSi) Bronze I Bronze II Bronze III Constantan (WM 50) Manganin Brass Nickel silver (WM 30) Nickel chromium Niccolite (WM 43) Platinum rhodium Steel wire (WM 13) Woods metal c) Other conductors Graphite Carbon, homog. Retort graphite
36 0.83 4.84 13 6.7...10 43.5 58 22 14.5 9.35 1.04 61 7.4 18.2 16.5 8.3
0.0278 1.2 0.2066 0.0769 0.15..0.1 0.023 0.01724 0.045 0.069 0.107 0.962 0.0164 0.135 0.055 0.061 0.12
n = speed (min -1) f = frequency (Hz) p = number of pole pairs Example: f = 50 Hz, p = 2 n 50 2 60 1500 min +1
Efficiency: r P ab P zu 100 %
1)
Example: Efficiency and power factor of a four-pole 1.1-kW motor and a 132-kW motor dependent on the load
cos
P U cos
30.0 48 36 18 2.0 2.32 15.9 3.33 0.92 2.32 5.0 7.7 1.85
0.033 0.02083 0.02778 0.05556 0.50 0.43 0.063 0.30 1.09 0.43 0.20 0.13 0.54
Power factor cos
Efficiency
Single-phase alternating current
132-kW motor
1.1-kW motor
Three-phase current
1.73
cos
1.73
P U cos
0.046 0.015 0.014
22 65 70
Resistance of a conductor: l l R A p A R l A = = = = = resistance () length of conductor (m) electric conductivity (m/ mm2) cross section of conductor (mm2) specific electrical resistance ( mm2)/m)
Power output P / PN
1) Pab = mechanical output power on the motor shaft Pzu = absorbed electric power
74
75
Electrical Engineering Types of Construction and Mounting Arrangements of Rotating Electrical Machinery
Types of construction and mounting arrangements of rotating electrical machinery [Extract from DIN/IEC 34, Part 7 (4.83)] Machines with end shields, horizontal arrangement Design
Symbol Figure Bearings 2 end shields 2 end shields 2 end shields 2 end shields 2 end shields 2 end shields Stator (Housing) with feet without feet Shaft free shaft end free shaft end free shaft end free shaft end free shaft end free shaft end
Electrical Engineering Types of Protection for Electrical Equipment (Protection Against Contact and Foreign Bodies)
Types of protection for electrical equipment [Extract from DIN 40050 (7.80)] Example of designation
Design/Explanation Fastening or Installation installation on substructure
Explanation
General design
Type of protection
DIN 40050
IP
Designation DIN number Code letters First type number Second type number
B3
mounting flange close to bearing, access from housing side design B3, if necessary end shields turned through -90 design B3, if necessary end shields turned through 90 design B3, if necessary end shields turned through 180 mounting flange close to bearing, access from housing side
B5
flanged
An enclosure with this designation is protected against the ingress of solid foreign bodies having a diameter above 1 mm and of splashing water. Degrees of protection for protection against contact and foreign bodies (first type number) First type number 0 1 Degree of protection (Protection against contact and foreign bodies) No special protection Protection against the ingress of solid foreign bodies having a diameter above 50 mm (large foreign bodies) 1) No protection against intended access, e.g. by hand, however, protection of persons against contact with live parts Protection against the ingress of solid foreign bodies having a diameter above 12 mm (medium-sized foreign bodies) 1) Keeping away of fingers or similar objects Protection against the ingress of solid foreign bodies having a diameter above 2.5 mm (small foreign bodies) 1) 2) Keeping away tools, wires or similar objects having a thickness above 2.5 mm Protection against the ingress of solid foreign bodies having a diameter above 1 mm (grain sized foreign bodies) 1) 2) Keeping away tools, wires or similar objects having a thickness above 1 mm Protection against harmful dust covers. The ingress of dust is not entirely prevented, however, dust may not enter to such an amount that operation of the equipment is impaired (dustproof). 3) Complete protection against contact Protection against the ingress of dust (dust-tight) Complete protection against contact
B6
with feet
wall fastening, feet on LH side when looking at input side wall fastening, feet on RH side when looking at input side
B7
with feet
B8
with feet
fastening on ceiling
B 35
with feet
installation on substructure with additional flange
3 Machines with end shields, vertical arrangement Design

Symbol Figure Bearings Stator (Housing) Shaft free shaft end at the bottom free shaft end at the top free shaft end at the bottom free shaft end at the top
Explanation
General design mounting flange close to bearing on input side, access from housing side mounting flange close to bearing on input side, access from housing side Design/Explanation Fastening or Installation
V1
2 end shields
without feet
flanged at the bottom
V3
2 end shields 2 end shields 2 end shields
without feet
flanged at the top
V5
with feet
fastening to wall or on substructure
V6
with feet
fastening to wall or on substructure
1) For equipment with degrees of protection from 1 to 4, uniformly or non-uniformly shaped foreign bodies with three dimensions perpendicular to each other and above the corresponding diameter values are prevented from ingress. 2) For degrees of protection 3 and 4, the respective expert commission is responsible for the application of this table for equipment with drain holes or cooling air slots. 3) For degree of protection 5, the respective expert commission is responsible for the application of this table for equipment with drain holes.
76
77
Electrical Engineering Types of Protection for Electrical Equipment (Protection Against Water)
Types of protection for electrical equipment [Extract from DIN 40050 (7.80)] Example of designation Designation DIN number Code letters First type number Second type number An enclosure with this designation is protected against the ingress of solid foreign bodies having a diameter above 1 mm and of splashing water. Degrees of protection for protection against water (second type number) Second type number 0 1 No special protection Protection against dripping water falling vertically. It may not have any harmful effect (dripping water). Protection against dripping water falling vertically. It may not have any harmful effect on equipment (enclosure) inclined by up to 15 relative to its normal position (diagonally falling dripping water). Protection against water falling at any angle up to 60 relative to the perpendicular. It may not have any harmful effect (spraying water). Protection against water spraying on the equipment (enclosure) from all directions. It may not have any harmful effect (splashing water). Protection against a water jet from a nozzle which is directed on the equipment (enclosure) from all directions. It may not have any harmful effect (hose-directed water). Protection against heavy sea or strong water jet. No harmful quantities of water may enter the equipment (enclosure) (flooding). Protection against water if the equipment (enclosure) is immersed under determined pressure and time conditions. No harmful quantities of water may enter the equipment (enclosure) (immersion). The equipment (enclosure) is suitable for permanent submersion under conditions to be described by the manufacturer (submersion). 1) Degree of protection (Protection against water) Type of protection DIN 40050 IP 4 4
Electrical Engineering Explosion Protection of Electrical Switchgear
Explosion protection of electrical switchgear Example of designation / Type of protection [Extract from DIN EN 50014 ... 50020] Example of designation Symbol for equipment certified by an EC testing authority Symbol for equipment made according to European Standards Type of protection Explosion group Temperature class Types of protection Type of protection Flameproof enclosure Symbol d Gap-s Scheme Application Heavy-current engineering (commutator) motors, transformers, switchgear, lighting fittings, and other spark generating parts Ex EEx d II B T3
Pressurized enclosure
3 4
Especially for large apparata, switchgears, motors, generators
Oil-immersion enclosure Sand-filled enclosure Increased safety
Switchgears, transformers
Capacitors
Squirrel-cage motors, terminal and junction boxes, lighting fittings, current transformers, measuring and control devices
1) This degree of protection is normally for air-tight enclosed equipment. For certain equipment, however, water may enter provided that it has no harmful effect.
Intrinsic safety
Low-voltage engineering: measuring and control devices (electrical equipment and circuits)
Potentially explosive atmosphere
78
79
Electrical Engineering Explosion Protection of Electrical Switchgear
Explosion protection of electrical switchgear Designation of electrical equipment / Classification of areas acc. to gases and vapours [Extract from DIN EN 50014 ... 50020] Designation of electrical equipment Designation acc. to Firedamp protection Explosion protection Classification according to gases and vapours For flame proof enclosures: maximum width of gap > 0.9 mm 0.5 - 0.9mm < 0.5 mm
For intrinsically safe circuits: minimum ignition current ratio referred to methane 1)
Materials Conversion of Fatigue Strength Values of Miscellaneous Materials Mechanical Properties of Quenched and Tempered Steels
Page 82 83 84 85 86 87 88 89 89 90 91 91 92 92 93 94 95 96 97 97 97 98
VDE 0170/0171/2.61 Sch Ex Explosion class
EN 50014 ... 50020 EEx..I EEx..II Explosion group
Fatigue Strength Diagrams of Quenched and Tempered Steels General-Purpose Structural Steels Fatigue Strength Diagrams of General-Purpose Structural Steels Case Hardening Steels Fatigue Strength Diagrams of Case Hardening Steels Cold Rolled Steel Strips for Springs
> 0.8 mm 0.45 - 0.8mm < 0.45 mm
1 2 3a ... 3n Ignition group Ignition temperature C G1> 450 G2> 300...450 G3> 200...300 G4> 135...200 G5 from 100...135 Permissible limiting temperature C 360 240 160 110 80
A B C Temperature class Ignition Maximum temperature surface temperature C C T1 > 450 450 T2 > 300 300 T3 > 200 200 T4 > 135 135 T5 > 100 100 T6 > 85 85
Cast Steels for General Engineering Purposes Round Steel Wire for Springs Lamellar Graphite Cast Iron
Ignition temperature of gases and vapours in C
Nodular Graphite Cast Iron Copper-Tin- and Copper-Zinc-Tin Casting Alloys Copper-Aluminium Casting Alloys Aluminium Casting Alloys Lead and Tin Casting Alloys for Babbit Sleeve Bearings Comparison of Tensile Strength and Miscellaneous Hardness Values Values of Solids and Liquids Coefficient of Linear Expansion Iron-Carbon Diagram Fatigue Strength Values for Gear Materials Heat Treatment During Case Hardening of Case Hardening Steels
1) For definition, see EN 50014, Annex A
Classification of areas according to gases and vapours Zone 0 Areas with permanent or long-term potentially explosive atmospheres. Zone 1 Areas where potentially explosive atmospheres are expected to occur occasionally. Zone 2 Areas where potentially explosive atmospheres are expected to occur only rarely and then only for short periods.
Safe area
ZONE Potentially explosive atmosphere Existing explos. atmosphere permanent or long-term probably during normal operation (occasionally) rarely and at short terms
practically never
Ignition sources
(n) additionally
80
81
Materials Conversion of Fatigue Strength Values of Miscellaneous Materials

Conversion of fatigue strength values of miscellaneous materials Tension 3) Material Structural steel Quenched and tempered steel W 0.45 Rm Sch 1.3 W 1.7 W 1.6 W 1.6 W bW Bending 1) bSch bF 1.5 Re tW 0.35 Rm Torsion 1) tSch 1.1 tW 1.6tW 1.4tW 1.6tW F 0.7 Re
Materials Mechanical Properties of Quenched and Tempered Steels

Quenched and tempered steels [Extract from DIN 17200 (3.87)] Mechanical properties of steels in quenched and tempered condition (Code letter V)
Diameter Steel grade up to 16 mm
Yield point (0.2 MateGr) rial N/mm2 no. min. R e, Rp 0.2
above 16 up to 40 mm
Yield point (0.2 Gr) N/mm2 min.
Re, Rp 0.2
Yield point (0.2 Gr) N/mm2 min. R e, Rp 0.2


0.49 Rm 1.5 bW 0.44 Rm 1.7 bW 0.41 Rm 1.7 bW 0.37 Rm 1.8 bW 0.40 Rm
0.41 Rm
1.4 Re
0.30 Rm
0.7 Re
Symbol
Tensile strength N/mm2 Rm
Case harden0.40 Rm ing steel 2) Grey cast iron 0.25 Rm Light metal 0.30 Rm
1.4 Re
0.30 Rm 0.36 Rm 0.25 Rm
0.7 Re
C 22 C 35 C 45 C 55 C 60 Ck 22 Ck 35 Cm 35 Ck 45 Cm 45 Ck 55 Cm 55 Ck 60 Cm 60 28 Mn 6 38 Cr 2 46 Cr 2 34 Cr 4 34 Cr S4 37 Cr 4 37 Cr S4 41 Cr 4 41 Cr S4 25 CrMo 4 34 CrMo 4 34 CrMo S4 42 CrMo 4 42 CrMo S4 50 CrMo 4
1.0402 1.0501 1.0503 1.0535 1.0601 1.1151 1.1181 1.1180 1.1191 1.1201 1.1203 1.1209 1.1221 1.1223 1.1170 1.7003 1.7006 1.7033 1.7037 1.7034 1.7038 1.7035 1.7039 1.7218 1.7220 1.7226 1.7225 1.7227 1.7228
350 430 500 550 580 350 430 430 500 500 550 550 580 580 590
550 700 630 780 700 850 800 950 8501000 550 700 630 780 630 780 700 850 700 850 800 950 800 950 8501000 8501000 780 930
300 370 430 500 520 300 370 370 430 430 500 500 520 520 490
500 600 650 750 800 500 600 600 650 650 750 750 800 800
650 750 800 900 950 650 750 750 800 800 900 900 950 950
320 370 430 450 320 320 370 370 430 430 450 450 440 350 400 460 460 510 510 560 560 450 550 550 650 650 700
550 630 700 750 550 550 630 630 700 700 750 750
700 780 850 900
400 500 500 550 550 650
650 800 750 900 750 900 800 950 800 950 8501000
450 450 500 500 550
700 850 700 850 750 900 750 900 800 950 750 900 800 950 9001100 800 950 9001100
1) For polished round section test piece of about 10 mm diameter. 2) Case-hardened; determined on round section test piece of about 30 mm diameter. Rm and Re of core material. 3) For compression, Sch is larger, e.g. for spring steel dSch 1.3 Sch For grey cast iron dSch 3 . Sch Ultimate stress values Rm Re W Sch bW bSch bF tW tSch tF Tensile strength Yield point Fatigue strength under alternating stresses Fatigue strength under fluctuating stresses Fatigue strength under alternating stresses Fatigue strength under fluctuating stresses Yield point Fatigue strength under alternating stresses Fatigue strength under fluctuating stresses Yield point Type of load Tension Tension Tension Tension Bending Bending Bending Torsion Torsion Torsion
700 700 780 780 850 850 900 900
690 840 700 850 800 950 800 950 800 950 8501000 8501000 9001100 9001100 800 950 9001100 9001100 10001200 10001200 10001200
640 790 600 650 700 700 750 750 800 800 750 800 850 850 900 900 950 950
550 800 950 450 650 9001100 550 700 9001100 590 700 9001100 590 750 9501150 630 750 9501150 630 800 10001200 660 800 10001200 660 700 800 800 900 900 900 9001100 10001200 10001200 11001300 11001300 11001300 600 650 650 750 750 780
700 850 800 950 800 950 9001100 9001100 9001100
36 CrNiMo 4 1.6511 900 11001300 800 10001200 700 34 CrNiMo 6 1.6582 1000 12001400 900 11001300 800 30 CrNiMo 6 1.6580 1050 12501450 1050 12501450 900 50 CrV 4 1.8159 900 11001300 800 10001200 700 30 CrMoV9 1.7707 1050 12501450 1020 12001450 900
9001100 600 10001200 700 11001300 800 9001100 11001300 650 800
800 950 550 9001100 600 10001200 700 8501000 600 10001200 700
82
83
Materials Fatigue Strength Diagrams of Quenched and Tempered Steels

Fatigue strength diagrams of quenched and tempered steels, DIN 17200 (in quenched and tempered condition, test piece diameter d = 10 mm)
Materials General-Purpose Structural Steels
General-purpose structural steels [Extract from DIN 17100 (1.80)] Steel grade TreatSimilar steel Tensile strength Rm Upper yield point ReH in N/mm2 ment grades in N/mm2 for product roduct (minimum) for product roduct thickness in condi condithickness in mm mm EURON. 25 tion
1)
Symbol
Mate Material no.
<3 Fe 310-0 Fe 360-BFU 310... 540
3 >16 >40 >63 >80 >100 16 >100 100 40 63 80 100 290 185 175
2)
St 33
1.0035 U, N
St 37-2 1.0037 U, N U St 37-2 1.0036 U, N
235 225 215 205 195 360... 340... 360 340 510 470 To be agreed upon To be agreed upon 235 225 215 215 215
R St 37-2 1.0038 U, N, Fe 360-BFN St 37-3 1.0116 U N Fe 360-C Fe 360-D Fe 430-B Fe 430-C Fe 430-D Fe 510-C Fe 510-D Fe 490-2 Fe 590-2 Fe 690-2
St 44-2 1.0044 U, N St 44-3 St 44-3 1.0144 a) Tension/compression fatigue strength c) Torsional fatigue strength St 52-3 1.0570 U N U N
430... 410... 580 540
275 265 255 245 235
510... 490... 680 630 490... 470... 660 610 590... 570... 770 710 690... 670... 900 830
355 345 335 325 315
St 50-2 1.0050 U, N Quenched and tempered steels not illustrated may be used as follows: 34 CrNiMo 6 30 CrMoV 4 42 CrMo 4 36 CrNiMo 4 50 CrV 4 34 CrMo 4 28 Cr 4 C 45 C 22 like 30 CrNiMo 8 like 30 CrNiMo 8 like 50 CrMo 4 like 50 CrMo 4 like 50 CrMo 4 like 41 Cr 4 like 46 Cr 2 like Ck 45 like Ck 22 St 60-2 1.0060 U, N St 70-2 1.0070 U, N
295 285 275 265 255 335 325 315 305 295 365 355 345 335 325
1) N normalized; U hot-rolled, untreated 2) This value applies to thicknesses up to 25 mm only
C 60 and C 50 lie approximately between Ck 45 and 46 Cr 2. C 40, 32 Cr 2, C 35 , C 30 and C 25 lie approximately between Ck 22 and Ck 45. Loading type I: static Loading type II: dynamic b) Bending fatigue strength Loading type III: alternating
84
85
Materials Fatigue Strength Diagrams of General-Purpose Structural Steels

Fatigue strength diagrams of general-purpose structural steels, DIN 17100 (test piece diameter d = 10 mm)
Materials Case Hardening Steels
Case hardening steels; Quality specifications to DIN 17210 (12.69) from SI tables (2.1974) of VDEh Steel grade Treatment condition 1) For dia. 11 Yield point Re N/mm2 min. 390 390 440 440 440 For details, see DIN 17210 510 635 635 735 735 635 635 735 735 685 835 835 Tensile strength Rm N/mm2 640 790 640 790 740 890 740 890 740 890 7801030 8801180 8801180 10801380 10801380 8801180 8801180 10801380 10801380 9601280 12301480 11801430 For dia. 30 Yield point Re N/mm2 min. 295 295 355 355 355 440 590 590 685 685 590 590 685 685 635 785 785 Tensile strength Rm N/mm2 490 640 490 640 590 790 590 790 590 790 690 890 7801080 7801080 9801280 9801280 7801080 7801080 9801280 9801280 8801180 11801430 10801330 For dia. 63 Yield point Re N/mm2 min. 440 440 540 540 540 685 685 640 940 640 940 7801080 7801080 7801080 10801330 9801280 Tensile strength Rm N/mm2
Symbol
Material no.
C 10 Ck 10 C 15 Ck 15 Cm 15 15 Cr 13 16 MnCr 5 16 MnCrS 5 20 MnCr 5 20 MnCrS5 a) Tension/compression fatigue strength 20 MoCr 4 20 MoCrS 4 25 MoCrS4 25 MoCrS 4 15 CrNi 6 18 CrNi 8
1.0301 1.1121 1.0401 1.1141 1.1140 1.7015 1.7131 1.7139 1.7147 1.7149 1.7321 1.7323 1.7325 1.7326 1.5919 1.5920
c) Torsional fatigue strength
17 CrNiMo 6 1.6587
1) Dependent on treatment, the Brinell hardness is different. Treatment condition C G BF BG Meaning treated for shearing load soft annealed treated for strength treated for ferrite/pearlite structure
Loading type I: static Loading type II: dynamic b) Bending fatigue strength Loading type III: alternating
86
87
Materials Fatigue Strength Diagrams of Case Hardening Steels

Fatigue strength diagrams of case hardening steels, DIN 17210 (Core strength after case hardening, test piece diameter d = 10 mm)
Materials Cold Rolled Steel Strips for Springs Cast Steels for General Engineering Purposes
Cold rolled steel strips for springs [Extract from DIN 17222 (8.79)]
Steel grade Symbol C 55 Ck 55 C 60 Ck 60 C 67 Ck 67 C 75 CK75 Ck 85 CK 101 55 Si 7 71 Si 7 67 SiCr 5 Material no. 1.0535 1.1203 1.0601 1.1221 1.0603 1.1231 1.0605 1.1248 1.1269 1.1274 1.0904 1.5029 1.7103 1.8159
Comparable Com arable grade acc. to EURONORM 132 1 CS 55 2 CS 55 1 CS 60 2 CS 60 1 CS 67 2 CS 67 1 CS 75 2 CS 75 2 CS 85 CS 100 67 SiCr 5 50 CrV 4
Degree of conformity 1) F F F F F F F F F F f F
Tensile strength Rm
2)
N/mm2 maximum 610 620 640 640 670 690 740 800 800 740
a) Tension/compression fatigue strength
50 CrV 4 c) Torsional fatigue strength
1) F = minor deviations f = substantial deviations 2) Rm for cold rolled and soft-annealed condition; for strip thicknesses up to 3 mm
Cast steels for general engineering purposes [Extract from DIN 1681 (6.85)] Cast steel grade Yield point Re, e Rp 0 0.2 2 Symbol Material no. Tensile strength Rm Notched bar impact work (ISO-V-notch specimens) Av 30 mm > 30 mm
N/mm2 min. 200 230 260 300
N/mm2 min. 380 450 520 600
Mean value 1) J min. 35 27 27 27 35 27 22 20
Case hardening steels not illustrated may be used as follows: 25 MoCr 4 like 20 MnCr 5 17 CrNiMo 6 like 18 CrNi 8
GS-38 GS-45 GS-52 GS-60
1.0420 1.0446 1.0552 1.0558
Loading type I: static Loading type II: dynamic b) Bending fatigue strength Loading type III: alternating
The mechanical properties apply to specimens which are taken from test pieces with thicknesses up to 100 mm. Furthermore, the yield point values also apply to the casting itself, in so far as the wall thickness is 100 mm. 1) Determined from three individual values each.
88
89
Materials Round Steel Wire for Springs
Materials Lamellar Graphite Cast Iron Nodular Graphite Cast Iron

Lamellar graphite cast iron [Extract from DIN 1691 (5.85)] D Grade Material Symbol GG-10 GG-15 Number 0.6010 0.6015 Wall thicknesses in mm above 5 10 20 40 80 10 20 40 80 10 20 40 80 10 20 40 80 10 20 40 80 up to 40 20 40 80 150 20 40 80 150 20 40 80 150 20 40 80 150 20 40 80 150 Tensile strength 1) Rm N/mm2 min. 100 2) 130 110 95 80 180 155 130 115 225 195 170 155 270 240 210 195 315 280 250 225 Brinell hardness
1)
Round steel wire for springs [Extract from DIN 17223, Part 1 (12.84)] Grade of wire Diameter of wire mm 0.07 0.3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 17201970 15201750 14101620 13201520 12601450 12101390 11601340 11201300 10901260 10601230 A B C
Tensile strength Rm in N/mm2 23702650 19802220 17601970 16301830 15301730 14601650 14001580 13501530 13101480 12701440 12401400 12101370 11801340 11601310 11301280 11101260 10901230 10701210 10501190 10301170 10201150 19802200 18402040 17401930 16601840 15901770 15401710 14901660 14501610 14101570 13801530 13501500 13201470 12901440 12701410 12401390 12201360 12001340 11801320 11601300 28003100 26602940 22302470 19802200 18402040
Compressive strength 2) dB N/mm2 600
HB 30 225 205 250 235 265 250 285 265 285 275
GG-20 17401930 16601840 15901770 15401710 14901660 14501610 14101570 13801530 13501500 13201470 12901440 12701410 12401390 12201360 12001340 11801320 GGG-40.3 11601300 GGG-40 GGG-50 GGG-60 GGG-70 GG-35 GG-30 GG-25
0.6020
720
0.6025
840
0.6030
960
0.6035
1080
The values apply to castings which are made in sand moulds or moulds with comparable heat diffusibility. 1) These values are reference values. 2) Values in the separately cast test piece with 30 mm diameter of the unfinished casting. Nodular graphite cast iron [Extract from DIN 1693, Part 2 (10.77)] Properties in cast-on test pieces Grade Material Symbol Number 0.7043 0.7040 0.7050 0.7060 0.7070 Wall thickness of casting mm from 30 above 60 from 30 above 60 from 30 above 60 from 30 above 60 from 30 above 60 mm up to 60 up to 200 up to 60 up to 200 up to 60 up to 200 up to 60 up to 200 up to 60 up to 200 Thickness of cast-on test piece mm 40 70 40 70 40 70 40 70 40 70 Tensile strength Rm N/mm2 390 370 390 370 450 420 600 550 700 650 0.2% proof stress Rp0.2 N/mm2 250 240 250 240 300 290 360 340 400 380
90
91
Materials Copper-Tin- and Copper-Zinc-Tin Casting Alloys Copper-Aluminium Casting Alloys

Copper-tin- and copper-zinc-tin casting alloys [Extract from DIN 1705 (11.81)] Material Symbol G-CuSn 12 GZ-CuSn 12 GC-CuSn12 G-CuSn 12 Ni GZ-CuSn 12 Ni GC-CuSn 12 Ni G-CuSn 12 Pb GZ-CuSn 12 Pb GC-CuSn 12 Pb G-CuSn 10 G-CuSn 10 Zn G-CuSn 7 ZnPb GZ-CuSn 7 ZnPb GC-CuSn 7 ZnPb G-CuSn 6 ZnNi G-CuSn 5 ZnPb G-CuSn 2 ZnPb Number 2.1052.01 2.1052.03 2.1052.04 2.1060.01 2.1060.03 2.1060.04 2.1061.01 2.1061.03 2.1061.04 2.1050.01 2,1086.01 2.1090.01 2.1090.03 2.1090.04 2.1093.01 2.1096.01 2.1098.01 Sand-mould cast iron Centrifugally cast iron Continuously cast iron Sand-mould cast iron Centrifugally cast iron Continuously cast iron Sand-mould cast iron Centrifugally cast iron Continuously cast iron Sand-mould cast iron Sand-mould cast iron Sand-mould cast iron Centrifugally cast iron Continuously cast iron Sand-mould cast iron Sand-mould cast iron Sand-mould cast iron Condition on delivery 0.2% proof stress 1) Rp0.2 min. in N/mm2 140 150 140 160 180 170 140 150 140 130 130 120 130 120 140 90 90 Tensile strength 1) Rm min. in N/mm2 260 280 280 280 300 300 260 280 280 270 260 240 270 270 270 220 210
Materials Aluminium Casting Alloys
Aluminium casting alloys [Extract from DIN 1725 (2.86)] Material Symbol G-AlSi 12 G-AlSi 12 g GK-AlSi 12 GK-AlSi 12 g G-AlSi 10 Mg G-AlSi 10 Mg wa GK-AlSi 10 Mg GK-AlSi 10 Mg wa G-AlSi 11 G-AlSi 11 g GK-AlSi 11 GK-AlSi 11g G-AlSi 7 Mg wa GK-AlSi 7 Mg wa GF-AlSi 7 Mg wa G-AlMg 3 Si G-AlMg 3 Si wa GK-AlMg 3 Si GK-AlMg 3 Si wa GF-AlMg 3 Si wa Number 3.2581.01 3.2581.44 3.2581.02 3.2581.45 3.2381.01 3.2381.61 3.2381.02 3.2381.62 3.2211.01 3.2211.81 3.2211.02 3.2211.82 3.2371.61 3.2371.62 3.2371.63 3.3241.01 3.3241.61 3.3241.02 3.3241.62 3.3241.63 Sand-mould cast iron as cast Sand-mould cast iron annealed and quenched Chilled casting as cast Chilled casting annealed and quenched Sand-mould cast iron as cast Sand-mould cast iron temper-hardened Chilled casting as cast Chilled casting temper-hardened Sand-mould cast iron as cast annealed Chilled casting as cast annealed Sand-mould cast iron temper-hardened Chilled casting temper-hardened High-quality casting temper-hardened Sand-mould cast iron as cast Sand-mould cast iron temper-hardened Chilled casting as cast Chilled casting temper-hardened Chilled casting temper-hardened Casting method and condition on delivery 0.2 proof stress Rp0.2 in N/mm2 70 up to 100 70 up to 100 80 up to 110 80 up to 110 80 up to 110 180 up to 260 90 up to 120 210 up to 280 70 up to 100 70 up to 100 80 up to 110 80 up to 110 190 up to 240 200 up to 280 200 up to 260 80 up to 100 120 up to 160 80 up to 100 120 up to 180 120 up to 160 Tensile strength Rm in N/mm2 150 up to 200 150 up to 200 170 up to 230 170 up to 230 160 up to 210 220 up to 320 180 up to 240 240 up to 320 150 up to 200 150 up to 200 170 up to 230 170 up to 230 230 up to 310 250 up to 340 260 up to 320 140 up to 190 200 up to 280 150 up to 200 220 up to 300 200 up to 280
1) Material properties in the test bar Copper-aluminium casting alloys [Extract from DIN 1714 (11.81)] Material Symbol G-CuAl 10 Fe GK-CuAl 10 Fe GZ-CuAl 10 Fe G-CuAl 9 Ni GK-CuAl 9 Ni GZ-CuAl 9 Ni G-CuAl 10 Ni GK-CuAl 10 Ni GZ-CuAl 10 Ni GC-CuAl 10 Ni G-CuAl 11 Ni GK-CuAl 11 Ni GZ-CuAl 11 Ni G-CuAl 8 Mn GK-CuAl 8 Mn Number 2.0940.01 2.0940.02 2.0940.03 2.0970.01 2.0970.02 2.0970.03 2.0975.01 2.0975.02 2.0975.03 2.0975.04 2.0980.01 2.0980.02 2.0980.03 2.0962.01 2.0962.02 Sand-mould cast iron Chilled casting Centrifugally cast iron Sand-mould cast iron Chilled casting Centrifugally cast iron Sand-mould cast iron Chilled casting Centrifugally cast iron Continuously cast iron Sand-mould cast iron Chilled casting Centrifugally cast iron Sand-mould cast iron Chilled casting 0.2% proof stress 1) Rp0.2 min. in N/mm2 Tensile strength 1) Rm min. in N/mm2
Condition on delivery
180 200 200 200 230 250 270 300 300 300 320 400 400 180 200
500 550 550 500 530 600 600 600 700 700 680 680 750 440 450
1) Material properties in the test bar
92
93
Materials Lead and Tin Casting Alloys for Babbit Sleeve Bearings
Materials Comparison of Tensile Strength and Miscellaneous Hardness Values

Vickers Tensile hardstrength ness N/mm2 (F>98N) 255 270 285 305 320 335 350 370 385 400 415 430 450 465 480 495 510 530 545 560 575 595 610 625 640 660 675 690 705 720 740 755 770 785 800 820 835 850 865 880 900 915 930 950 965 995 1030 1060 1095 1125 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240 245 250 255 260 265 270 275 280 285 290 295 300 310 320 330 340 350 Brinell hardness 2)
F N 0.102 + ) 30 D2 mm 2
Lead and tin casting alloys for babbit sleeve bearings [Extract from DIN ISO 4381 (10.82)] Grade Material Symbol PbSb 15 SnAs PbSb 15 Sn 10 PbSb 14 Sn 9 CuAs PbSb 10 Sn 6 SnSb 12 Cu 6 Pb SnSb 8 Cu 4 SnSb 8 Cu 4 Cd Number 2.3390 2.3391 2.3392 2.3393 2.3790 2.3791 2.3792 Brinell hardness 1) HB 10/250/180 20 C 18 21 22 16 25 22 28 50 C 15 16 22 16 20 17 25 120 C 14 14 16 14 12 11 19 0.2% proof stress 1) Rp 0.2 in N/mm2 20 C 39 43 46 39 61 47 62 50 C 37 32 39 32 60 44 44 100 C 25 30 27 27 36 27 30
Rockwell hardness HRB HRC HRA HRD 1)
Vickers Tensile hardstrength ness N/mm2 (F>98N) 1155 1190 1220 1255 1290 1320 1350 1385 1420 1455 1485 1520 1555 1595 1630 1665 1700 1740 1775 1810 1845 1880 1920 1955 1995 2030 2070 2105 2145 2180 360 370 380 390 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650 660 670 680 690 700 720 740 760 780 800 820 840 860 880 900 920 940
Brinell hardness 2)
F N 0.102 + ) 30 D2 mm 2
Rockwell hardness HRC HRA 36.6 37.7 38.8 39.8 40.8 41.8 42.7 43.6 44.5 45.3 46.1 46.9 47.7 48.4 49.1 49.8 50.5 51.1 51.7 52.3 53.0 53.6 54.1 54.7 55.2 55.7 56.3 56.8 57.3 57.8 58.3 58.8 59.2 59.7 60.1 61.0 61.8 62.5 63.3 64.0 64.7 65.3 65.9 66.4 67.0 68.7 69.2 69.8 70.3 70.8 71.4 71.8 72.3 72.8 73.3 73.6 74.1 74.5 74.9 75.3 75.7 76.1 76.4 76.7 77.0 77.4 77.8 78.0 78.4 78.6 78.9 79.2 79.5 79.8 80.0 80.3 80.6 80.8 81.1 81.3 81.8 82.2 82.6 83.0 83.4 83.8 84.1 84.4 84.7 85.0 HRD 1) 52.8 53.6 54.4 55.3 56.0 56.8 57.5 58.2 58.8 59.4 60.1 60.7 61.3 61.6 62.2 62.9 63.5 63.9 64.5 64.8 65.4 65.8 66.2 66.7 67.0 67.5 67.9 68.3 68.7 69.0 69.4 69.8 70.1 70.5 70.8 71.5 72.1 72.6 73.3 73.8 74.3 74.8 75.3 75.7 76.1
76.0 80.7 85.5 90.2 95.0 99.8 105 109 114 119 124 128 133 138 143 147 152 156 162 166 171 176 181 185 190 195 199 204 209 214 219 223 228 233 238 242 247 252 257 261 266 271 276 280 285 295 304 314 323 333
41.0 48.0 52.0 56.2 62.3 66.7 71.2 75.0 78.7 81.7 85.0 87.1 89.5 91.5 92.5 93.5 94.0 95.0 96.0 96.7 98.1 20.3 60.7 40.3 21.3 61.2 41.1 99.5 22.2 61.6 41.7 23.1 (101) 24.0 24.8 (102) 25.6 26.4 (104) 27.1 27.8 (105) 28.5 29.2 29.8 31.0 32.3 33.3 34.4 35.5 62.0 62.4 62.7 63.1 63.5 63.8 64.2 64.5 64.8 65.2 65.8 66.4 67.0 67.6 68.1 42.2 43.1 43.7 44.3 44.9 45.3 46.0 46.5 47.1 47.5 48.4 49.4 50.2 51.1 51.9
342 352 361 371 380 390 399 409 418 428 437 447 (456) (466) (475) (485) (494) (504) (513) (523) (532) (542) (551) (561) (570) (580) (589) (599) (608) (618)
1) Material properties in the test bar
67.5 85.3 76.5 68.0 85.6 76.9
The figures in brackets are hardness values outside the domain of definition of standard hardness test methods which, however, in practice are frequently used as approximate values. Furthermore, the Brinell hardness values in brackets apply only if the test was carried out with a carbide ball. 1) Internationally usual, e.g. ASTM E 18-74 (American Society for Testing and Materials) 2) Calculated from HB = 0.95 HV (Vickers hardness) Determination of Rockwell hardness HRA, HRB, HRC, and HRD acc. to DIN 50103 Part 1 and 2 Determination of Vickers hardness acc. to DIN 50133 Part 1 Determination of Brinell hardness acc. to DIN 50351 Determination of tensile strength acc. to DIN 50145
94
95
Materials Values of Solids and Liquids
Materials Coefficient of Linear Expansion; Iron-Carbon Diagram; Fatigue Strength Values for Gear Materials
Mean density of the earth = 5.517 g/cm3
Symbol Density p g/cm3 Porcelain Pyranite Quartz-flint Radium Rhenium Rhodium Gunmetal (CuSn5ZnPb) Rubidium Ruthenium Sand, dry Sandstone Brick, fire Slate Emery Sulphur, rhombic Sulphur, monoclinic Barytes Selenium, red Silver Silicon Silicon carbide Sillimanite Soapstone (talcous) Steel, plain + low-alloy stainless 18Cr8Ni non-magnetic 15Ni7Mn Tungsten steel 18W Steanit Hard coal Strontium Tantalum Tellurium Thorium Titanium Tombac Uranium 99.99% Uranium 99.99% Vanadium Soft rubber White metal Bismuth Wolfram Cesium Cement, hard Cerium Zinc Tin Zirconium Melting point t in C Thermal conductivity at 20 C W/(mK)
Values of solids and liquids

Symbol Density p g/cm3 Agate Aluminium Aluminium bronze Antimony Arsenic Asbestos Asphaltum Barium Barium chloride Basalt, natural Beryllium Concrete Lead Boron (amorph.) Borax Limonite Bronze (CuSn6) Chlorine calcium Chromium Chromium nickel (NiCr 8020) Delta metal Diamond Iron, pure Grease Gallium Germanium Gypsum Glass, window Mica Gold Granite Graphite Grey cast iron Laminated fabric Hard rubber Hard metal K20 Al Sb As Ba Be Pb B 2.5...2.8 2.7 7.7 6.67 5.72 2.5 1.1...1.5 3.59 3.1 2.7...3.2 1.85 2 11.3 1.73 1.72 3.4...3.9 8.83 2.2 7.1 7.4 8.6 3.5 7.86 0.92...0.94 5.9 5.32 2.3 2.5 2.8 19.29 2.6...2.8 2.24 7.25 1.3...1.42 1.4 14.8 0.45...0.85 7.31 22.5 8.64 0.86 2.6 1.55 3.4 0.95 8.8 2.15 1.6...1.9 8.89 3.9...4 1.8...2.6 8.9 0.9....1 0.53 1.74 1.8...1.83 7.43 2.6...2.8 8.6...9.1 8.5 10.2 8.8 0.98 8.7 8.9 8.6 22.5 12 0.9 1.25 1.83 21.5 1.13 Thermal Melting conductivity point at 20 C t in C W/(mK) 1600 11.20 658 204 1040 128 630 22.5 1300 80...100 0.698 704 960 1.67 1280 1.65 1 327.4 34.7 2300 740 1565 910 64 774 1800 69 1430 52.335 950 104.7 1530 81 30...175 0.209 29.75 936 58.615 1200 0.45 700 0.81 1300 0.35 1063 310 3.5 3800 168 1200 58 0.34...0.35 0.17 2000 81 0.12...0.17 156 24 2450 59.3 321 92.1 63.6 110 2.2 850 2572 125 0.2 1490 69.4 802 0.184 1600 23.3 2050 12...23 0.92 1083 384 0.15 179 71 657 157 650 69.8..145.4 1250 30 1290 2.8 0.7 900 116 2600 145 1300 19.7 97.5 126 1020 48 1452 59 2415 54.43 2500 1552 70.9 52 0.26 0.13 44 1770 70 250 0.34
Coefficient of linear expansion The coefficient of linear expansion gives the fractional expansion of the unit of length of a substance per 1 degree K rise in temperature. For the linear expansion of a body applies: m+ T l ) lo + where l: change of length l: original length : coefficient of linear expansion T: rise of temperature
Coefficients of linear expansion of some substances at 0 ... 100 C Substance Aluminium alloys Grey cast iron (e.g. GG-20, GG-25) Steel, plain and low-alloy Steel, stainless (18Cr 8Ni) Steel, rapid machining steel Copper Brass CuZn37 Bronze CuSn8 [106/K] 21 ... 24 10.5 11.5 16 11.5 17 18.5 17.5
Substance (solid)
Substance (solid)
Ra Re Rh Rb Ru
S S Se Ag Si
Cr C Fe Ga Ge
Au C
Temperature in C
Sr Ta Te Th Ti
Woods Indium Iridium

Cadmium Potassium Limestone Calcium Calcium oxide (lime) Caoutchouc, crude Cobalt Salt, common Coke Constantan Corundum (AL2O3) Chalk Copper Leather, dry Lithium Magnesium Magnesium, alloyed Manganese Marble Red lead oxide Brass (63Cu37Zn) Molybdenum Monel metal Sodium Nickel silver
In Ir Cd K Ca Co
U V
Bi W Cs Ce Zn Sn Zr
Sec.cem. + pearlite
Sec.cem. + pearlite + ledeburite
Ledeburite
2.2...2.5 1650 1 3.3 1800 8.14 2.5...2.8 1480 9.89 5 700 21 3175 71 12.3 1960 88 8.8 950 38 1.52 39 58 12.2 2300 106 1.4...1.6 1480 0.58 2.1...2.5 1500 2.3 1.8...2.3 2000 1.2 2.6...2.7 2000 0.5 4 2200 11.6 2.07 112.8 0.27 1.96 119 0.13 4.5 1580 4.4 220 0.2 10.5 960 407 2.33 1420 83 3.12 15.2 2.4 1816 1.69 2.7 3.26 7.9 1460 47...58 7.9 1450 14 8 1450 16.28 8.7 1450 26 2.6...2.7 1520 1.63 1.35 0.24 2.54 797 0.23 16.6 2990 54 6.25 455 4.9 11.7 1800 38 4.5 1670 15.5 8.65 1000 159 1.8...2.6 1500..1700 0.93...1.28 18.7 1133 28 6.1 1890 31.4 1...1.8 0.14...0.23 7.5...10.1 300...400 34.9...69.8 9.8 271 8.1 19.2 3410 130 1.87 29 2...2.2 0.9...1.2 6.79 630 6.86 419 110 7.2 232 65 6.5 1850 22
Iron-carbon diagram
Mixed crystals Mixed crystals Melting + -mixed crystals Melting (Cementite)
-mixed crystals (austenite)
Melting + -mixed crystals -mixed crystals + sec. cementite + ledeburite
Melting + primary cementite
Primary cementite + ledeburite
(cubic face centered)
Mixed crystals
Pearlite
Mixed crystals (Ferrite)
-m.c. + sec.cem.
Primary cementite + ledeburite
Pearlite Boiling Thermal oint point conductiat vity 1.013MPa MP at 20 C C 35 25...210 80 210...380 290 150...300 > 175 316 380...400 65 24 > 360 > 40 > 150 357 102 338 W/(mK) 0.14 0.13 0.14 0.15 0.29 0.15 0.14 0.17 0.125 0.21 0.16 0.13 0.14 0.13 10 0.5 0.47 0.22
Cu Li Mg Mn
Substance (liquid)
Symbol
Density p g/cm3 at C 0.72 20 0.73 15 0.83 15 0.83 15 1.26 20 0.96 20 0.83 20 0.93 20 0.91 15 0.8 15 0.95 15 0.91 20 0.66 20 0.81 20 13.55 20 1.05 15 1.84 15 0.94 20
(cubic body centered)
Carbon content in weight percentage
Cementite content in weight percentage
Mo Na Ni Nb Os Pd P Pt
Nickel
Niobium Osmium Palladium Paraffin Pitch Phosphorus (white) Platinum Polyamide A, B
Ether Benzine Benzole, pure Diesel oil Glycerine Resin oil Fuel oil EL Linseed oil Machinery oil Methanol Methyl chloride Mineral oil Petroleum ether Petroleum Mercury Hydrochloric acid 10% Sulphuric acid, strong Silicon fluid
Pitting and tooth root fatigue strength of case hardening steels, DIN 17210 Hardness on finished gear Symbol HV1 16 MnCr 5 15 CrNi 6 17 CrNiMo 6 720 730 740 Hlim N/mm2 1470 1490 1510 Flim N/mm2 430 460 500
Hg
96
97
Materials Heat Treatment During Case Hardening of Case Hardening Steels

Heat treatment during case hardening of case hardening steels acc. to DIN 17210 Usual heat treatment during case hardening
A. Direct hardening or double hardening B. Single hardening C. Hardening after isothermal transformation
Lubricating Oils Viscosity-Temperature-Diagram for Mineral Oils Viscosity-Temperature-Diagram for Synthetic Oils of Polyglycole Base Viscosity-Temperature-Diagram for Synthetic Oils of Poly--Olefine Base Kinematic Viscosity and Dynamic Viscosity
Page 100 101 102 103 104
Direct hardening from carburizing temperature
Single hardening from core or case hardening temperature
Hardening after isothermal transformation in the pearlite stage (e)
Viscosity Table for Mineral Oils
Direct hardening after lowering to hardening temperature
Single hardening after intermediate annealing (soft annealing) (d)
Hardening after isothermal transformation in the pearlite stage (e) and cooling-down to room temperature
Double hardening
a b c d e
carburizing temperature hardening temperature tempering temperature temperature intermediate annealing (soft annealing) tem erature transformation temperature in the pearlite stage
Usual case hardening temperatures

Grade of steel Material number 1.0301 1.1121 1.0401 1.1141 1.1140 1.7016 1.7027 1.7028 1.7131 1.7139 1.7147 1.7149 1.7321 1.7323 1.7333 1.6523 1.6526 1.5919 1.6587 a Carburizing temperature
1)
b Case Core hardening hardening temperature 2) temperature 2) C C 880 up to 920 With regard to the properties of the component, the selection of the quenchant depends on the hardenability or casehardenability of the steel, the shape and cross section of the work piece to be hardened, as well as on the effect of the quenchant. Quenchant
c Tempering C
Symbol
C C 10 Ck 10 Ck 15 Cm 15 17 Cr 3 20 Cr 4 20 CrS 4 16 MnCr 5 16 MnCrS5 20 MnCr 5 20 MnCrS 5 20 MoCr 4 20 MoCrS 4 22 CrMoS 3 5 21 NiCrMo 2 21 NiCrMoS 2 15 CrNi 6 17 CrNiMo 6
880 up to 980
860 up to 900
780 up to 820
150 up to 200
830 up to 870
1) Decisive criteria for the determination of the carburizing temperature are mainly the required time of carburizing, the chosen carburizing agent, and the plant available, the provided course of process, as well as the required structural constitution. For direct hardening, carburizing usually is carried out at temperatures below 950 C. In special cases, carburizing temperatures up to above 1000 C are applied. 2) In case of direct hardening, quenching is carried out either from the carburizing temperature or any lower temperature. In particular if there is a risk of warping, lower hardening temperatures are preferred.
98
99
Lubricating Oils Viscosity-Temperature-Diagram for Mineral Oils
Lubricating Oils Viscosity-Temperature-Diagram for Synthetic Oils of Poly--Olefine Base
Viscosity-temperature-diagram for mineral oils
Viscosity-temperature-diagram for synthetic oils of poly--olefine base
Kinematic viscosity (mm2/s)
Temperature (C)
Temperature (C)
100
101
Lubricating Oils Viscosity-Temperature-Diagram for Synthetic Oils of Polyglycole Base
Lubricating Oils Kinematic Viscosity and Dynamic Viscosity for Mineral Oils at any Temperature
Kinematic viscosity Quantities for the determination of the kinematic viscosity VG grade 32 46 68 100 150 220 320 460 680 1000 1500 W40 [] 0.18066 0.22278 0.26424 0.30178 0.33813 0.36990 0.39900 0.42540 0.45225 0.47717 0.50192 W = m (2.49575 lgT) + W40 W m + 10 10 ) 0.8 m [-]: T [K]: W40 [-]: W [-]: [cSt]: 1) T = t + 273.15 [K] Dynamic viscosity
. 0.001 = = 15 (t 15) . 0.0007 .
Viscosity-temperature-diagram for synthetic oils of polyglycole base
m [] 3.7664 3.7231 3.6214 3.5562 3.4610 3.4020 3.3201 3.3151 3.2958 3.2143 3.1775 (1) (2)
slope thermodynamic temperature 1) auxiliary quantity at 40 C auxiliary quantity kinematic viscosity
(3) (4)
t [C]: temperature 3 15 [kg/dm ]: density at 15 C [kg/dm3]: density [cSt]: kinematic viscosity [Ns/m2]: dynamic viscosity Density 15 in kg/dm3 of lubricating oils for gear units ) (Example) 2) VG grade Temperature (C) ARAL Degol BG ESSO Spartan EP MOBIL OIL Mobilgear 626 ... 636 OPTIMOL Optigear BM TRIBOL Tribol 1100 68 0.890 0.880 0.882 0.890 0.890 100 0.890 0.885 0.885 0.901 0.895 150 0.895 0.890 0.889 0.904 0.901 220 0.895 0.895 0.876 0.910 0.907 320 0.900 0.900 0.900 0.917 0.912 460 0.900 0.905 0.905 0.920 0.920 680 0.905 0.920 0.910 0.930 0.934
2) Mineral base gear oils in accordance with designation CLP as per DIN 51502. These oils comply with the minimum requirements as specified in DIN 51517 Part 3. They are suitable for operating temperatures from -10 C up to +90 C (briefly +100 C).
102
103
Lubricating Oils Viscosity Table for Mineral Oils
Approx. A rox. ISO-VG assignment DIN to previous 51519 DIN 51502
Mean viscosity (40 C) and approx. viscosities in mm2/s (cSt) at
20 C cSt
40 C cSt
Approx. Saybolt assignment universal AGMA to seconds lubricant (SSU) at motorN at 40 C car motor 50 C 100 C (mean 40 C gear oils value) ) oils 1) 1) cSt Engler cSt SAE SAE
Cylindrical Gear Units Symbols and Units General Introduction Geometry of Involute Gears Concepts and Parameters Associated With Involute Teeth Reference Profile Module Tool Profile Generating Tooth Flanks Concepts and Parameters Associated With Cylindrical Gears Geometric Definitions Pitch Addendum Modification Concepts and Parameters Associated With a Cylindrical Gear Pair Definitions Mating Quantities Contact Ratios Summary of the Most Important Formulae Gear Teeth Modifications Load Carrying Capacity of Involute Gears Scope of Application and Purpose Basic Details General Factors Application Factor Dynamic Factor Face Load Factor Transverse Load Factor Tooth Flank Load Carrying Capacity Effective Hertzian Pressure Permissible Hertzian Pressure Tooth Root Load Carrying Capacity Effective Tooth Root Stress Permissible Tooth Root Stress Safety Factors Calculation Example Gear Unit Types Standard Designs Load Sharing Gear Units Comparisons Load Value Referred Torques Efficiencies Example Noise Emitted by Gear Units Definitions Measurements Determination via Sound Pressure Determination via Sound Intensity Prediction Possibilities of Influencing
Page 106/107 108 108 108 109 109 110 111 111 111 112 113 113 113 114 115-117 118/119 119/120 120/121 122 122 122 122 122 123 123 123/124 124 124/125 126 126 126/127 127 127 127/128 128 129 130 130 131 132 132 132/133 133 134
5 7 10 15 22 32
2 4 9
8 (1.7 E) 12 (2 E) 21 (3 E) 34 55 88
46 4.6 68 6.8 10 15 22 32 46 68 100 150 220 320 460 680 1000 1500
4 5 8 11 15 21 30 43 61 90 125 180 250 360 510 740
13 1.3 14 1.4 17 1.7 19 1.9 23 2.3 3 4 6 8 12 16 24 33 47 67 98
15 1.5 20 2.0 25 2.5 35 3.5 45 4.5 10 W 55 5.5 65 6.5 85 8.5 11 15 19 24 30 40 50 250 65 214 316 464 696 1020 1484 2132 3152 1 EP 2 2 EP 2.2 3.3 EP 4 4 EP 4.4 5 5 EP 5.5 6 6 EP 6.6 7 EP 8 EP 15 W 20 W 20 30 85 W 40 50 70 W 75 W 5W
16
25 46 36 68 49 100 150 220 320 460 680 1000 1500 68 92 114 144 169 225 324 345 550 865 1340 2060 3270 5170 8400 219 137
80 W
90
140
1) Approximate comparative value to ISO VG grades
104
105
Cylindrical Gear Units Symbols and units for cylindrical gear units
Cylindrical Gear Units Symbols and units for cylindrical gear units
mm mm mm mm mm mm mm mm mm mm mm Hz mm mm mm mm mm mm mm mm mm mm
Centre distance Reference centre distance Facewidth Bottom clearance between standard basic rack tooth profile and counter profile Reference diameter Tip diameter Base diameter Root diameter Pitch diameter Spacewidth on the reference cylinder Spacewidth on the standard basic rack tooth profile Frequency Length of path of contact Tooth depth Addendum Addendum of the standard basic rack tooth profile Addendum of the tools standard basic rack tooth profile Dedendum Dedendum of the standard basic rack tooth profile Dedendum of the tools standard basic rack tooth profile Tooth depth of the standard basic rack tooth profile Tooth depth of the tools standard basic rack tooth profile Protuberance height of the tools standard basic rack tooth profile Working depth of the standard basic rack tooth profile and the counter profile Tip diameter coefficient Module Normal module Transverse module modification
n p p pbt pe pen pet pex pt prPO q r ra rb rw s san sp sPO u v w x xE z A As BL
1/min N/mm2 mm mm mm mm mm mm mm
Speed Sound pressure Pitch on the reference circle Pitch on the base circle Normal base pitch Normal base pitch at a point Normal transverse pitch Axial pitch Transverse base pitch, reference circle pitch Protuberance value on the tools standard basic rack tooth profile Machining allowance on the cylindrical gear tooth flanks Reference circle radius, radius Tip radius Base radius Radius of the working pitch circle Tooth thickness on the reference circle Tooth thickness on the tip circle Tooth thickness of the standard basic rack tooth profile Tooth thickness of the tools standard basic rack tooth profile Gear ratio Circumferential speed on the reference circle Line load Addendum modification coefficient Generating addendum modification coefficient Number of teeth Gear teeth surface Tooth thickness deviation Load value
D Fn Ft G HV1 KA KF KF KH KH Kv LpA LWA P RZ SF SH S T V40 Y Y YFS YR YX Z Z ZH ZL ZV
mm N N kg dB dB kW m m2 Nm mm2/s
Construction dimension Load Nominal peripheral force at the reference circle Gear unit weight Vickers hardness at F = 9.81 N Application factor Transverse load factor (for tooth root stress) Face load factor (for tooth root stress) Transverse load factor (for contact stress) Face load factor (for contact stress) Dynamic factor Sound pressure level A Sound power level A Nominal power rating of driven machine Mean peak-to-valley roughness Factor of safety from tooth breakage Factor of safety from pitting Enveloping surface Torque Lubricating oil viscosity at 40 C Helix angle factor Contact ratio factor Tip factor Roughness factor Size factor Helix angle factor Contact ratio factor Zone factor Lubricant factor Speed factor
ZX
^
Size factor Transverse pressure angle at a point; Pressure angle Angle in the circular ^ ) m+ 180 measure Transverse pressure angle at the tip circle
ad b cp d da db df dw e ep f g h ha haP haPO hf hfP hfPO hp hPO hprPO
Degree rad Degree
at n P
Degree Normal pressure angle Pressure angle at a point of Degree the standard basic rack tooth profile
mm
Pressure angle at a point of PO Degree the tools standard basic rack tooth profile prPO Degree t wt b p Degree Degree Degree Protuberance pressure angle at a point Transverse pressure angle at the reference circle Working transverse pressure angle at the pitch circle Helix angle at the reference circle
mm mm mm mm mm mm mm mm
Degree Base helix angle

Transverse contact ratio Overlap ratio Total contact ratio Efficiency
Degree Working angle of the involute mm

mm
mm m/s N/mm m2 mm N/mm2
Radius of curvature Tip radius of curvature of the tools standard basic rack tooth profile Root radius of curvature of the tools standard basic rack tooth profile Effective Hertzian pressure Allowable stress number for contact stress Allowable Hertzian pressure Effective tooth root stress Bending stress number Allowable tooth root stress
aPO
fPO
mm
mm
N/mm2
hwP k m mn mt
mm
Hlim N/mm2 HP F FB N/mm2 N/mm2
mm mm mm
Flim N/mm2 N/mm2
Note: The unit rad may be replaced by 1.
106
107
Cylindrical Gear Units General Introduction Geometry of Involute Gears

1. Cylindrical gear units 1.1 Introduction In the industry, mainly gear units with case hardened and fine-machined gears are used for torque and speed adaptation of prime movers and driven machines. After carburising and hardening, the tooth flanks are fine-machined by hobbing or profile grinding or removing material (by means of shaping or generating tools coated with mechanically resistant material). In comparison with other gear units, which, for example, have quenched and tempered or nitrided gears, gear units with case hardened gears have higher power capacities, i.e. they require less space for the same speeds and torques. Further, gear units have the best efficiencies. Motion is transmitted without slip at constant speed. As a rule, an infinitely variable change-speed gear unit with primary or secondary gear stages presents the most economical solution even in case of variable speed control. In industrial gear units mainly involute gears are used. Compared with other tooth profiles, the technical and economical advantages are basically: H Simple manufacture with straight-sided flanked tools; H The same tool for all numbers of teeth; H Generating different tooth profiles and centre distances with the same number of teeth by means of the same tool by addendum modification; H Uniform transmission of motion even in case of centre distance errors from the nominal value; H The direction of the normal force of teeth remains constant during meshing; H Advanced stage of development; H Good availability on the market. When load sharing gear units are used, output torques can be doubled or tripled in comparison with gear units without load sharing. Load sharing gear units mostly have one input and one output shaft. Inside the gear unit the load is distributed and then brought together again on the output shaft gear. The uniform sharing of the load between the individual branches is achieved by special design measures. 1.2 Geometry of involute gears The most important concepts and parameters associated with cylindrical gears and cylindrical gear pairs with involute teeth in accordance with DIN 3960 are represented in sections 1.2.1 to 1.2.4. /1/ 1.2.1 Concepts and parameters associated with involute teeth 1.2.1.1 Standard basic rack tooth profile The standard basic rack tooth profile is the normal section through the teeth of the basic rack which is produced from an external gear tooth system with an infinitely large diameter and an infinitely large number of teeth. From figure 1 follows: The flanks of the standard basic rack tooth profile are straight lines and are located symmetrically below the pressure angle at a point P to the tooth centre line; Between module m and pitch p the relation is p = m; The nominal dimensions of tooth thickness and spacewidth on the datum line are equal, i.e. sP = eP = p/2; The bottom clearance cP between basic rack tooth profile and counter profile is 0.1 m up to 0.4 m; The addendum is fixed by haP = m, the dedendum by hfP = m + cP and thus, the tooth depth by hP = 2 m + cP; The working depth of basic rack tooth profile and counter profile is hwP = 2 m.
Cylindrical Gear Units Geometry of Involute Gears
1.2.1.2 Module The module m of the standard basic rack tooth profile is the module in the normal section mn of the gear teeth. For a helical gear with helix angle on the reference circle, the transverse module
in a transverse section is mt = mn/cos. For a spur gear = 0 and the module is m = mn = mt. In order to limit the number of the required gear cutting tools, module m has been standardized in preferred series 1 and 2, see table 1.
Table 1 Selection of some modules m in mm (acc. to DIN 780) Series 1 Series 2 1 1.25 1.5 1.75 2 2.5 3 3.5 4 4.5 5 6 7 8 9 10 12 14 16 18 20 22 25 32 28
1.2.1.3 Tool reference profile The tool reference profile according to figure 2a is the counter profile of the standard basic rack tooth profile according to figure 1. For industrial gear units, the pressure angle at a point of the tool reference profile PO = P is 20, as a rule. The tooth thickness sPO of the tool on the tool datum line depends on the stage of machining. The pre-machining tool leaves on both flanks of the teeth a machining allowance q for finishmachining. Therefore, the tooth thickness for pre-machining tools is sPO < p/2, and for finishmachining tools sPO = p/2. The pre-machining tool generates the root diameter and the fillet on a cylindrical gear. The finish-machining tool removes the machining allowance on the flanks, however, normally it does not touch the root circle - like on the tooth profile in figure 3a. Between pre- and finish- machining, cylindrical gears are subjected to a heat treatment which, as a rule, leads to warping of the teeth and growing of the root and tip circles.
Especially for cylindrical gears with a relatively large number of teeth or a small module there is a risk of generating a notch in the root on finish machining. To avoid this, pre-machining tools are provided with protuberance flanks as shown in figure 2b. They generate a root undercut on the gear, see figure 3b. On the tool, protuberance value prPO, protuberance pressure angle at a point prPO, as well as the tip radius of curvature ma PO must be so dimensioned that the active tooth profile on the gear will not be reduced and the tooth root will not be weakened too much. On cylindrical gears with small modules one often accepts on purpose a notch in the root if its distance to the root circle is large enough and thus the tooth root load carrying capacity is not impaired by a notch effect, figure 3c. In order to prevent the tip circle of the mating gear from touching the fillet it is necessary that a check for meshing interferences is carried out on the gear pair. /1/
Tip line
Counter profile
Datum line Standard basic rack tooth profile Root line Fillet Tooth root surface Tooth centre line Figure 1 Basic rack tooth profiles for involute teeth of cylindrical gears (acc. to DIN 867) a) Tool datum line b) Protuberance flank
Figure 2 Reference profiles of gear cutting tools for involute teeth of cylindrical gears a) For pre-machining and finish-machining b) For pre-machining with root undercut (protuberance)
108
109
Pre-machining
Finish-machining
1.2.2 Concepts and parameters associated with cylindrical gears 1.2.2.1 Geometric definitions In figure 6 the most important geometric quantities of a cylindrical gear are shown. The reference circle is the intersection of the reference cylinder with a plane of transverse section. When generating tooth flanks, the straight pitch line of the tool rolls off at the reference circle. Therefore, the reference circle periphery corresponds to the product of pitch p and number of teeth z, i.e. d = p z. Since mt = p/, the equation for the reference diameter thus is d = mt z. Many geometric quantities of the cylindrical gear are referred to the reference circle. For a helical gear, at the point of intersection of the involute with the reference circle, the trans-
Machining allowance q
Root undercut a) b)
Notch c)
Figure 3 Tooth profiles of cylindrical gears during pre- and finish-machining a) Pre- and finish-machining down to the root circle b) Pre-machining with root undercut (protuberance) c) Finish-machining with notch 1.2.1.4 Generating tooth flanks With the development of the envelope, an envelope line of the base cylinder with the base diameter db generates the involute surface of a spur gear. A straight line inclined by a base helix angle b to the envelope line in the developed envelope is the generator of an involute surface (involute helicoid) of a helical gear, figure 4. The involute which is always lying in a transverse section, figure 5, is described by the transverse Base cylinder envelope line Involute of base cylinder Involute helicoid Base cylinder Involute pressure angle at a point and radius r in the equations inv = tan r = rb / cos
^
verse pressure angle at a point in the transverse section is termed transverse pressure angle t, see figures 5 and 7. If a tangent line is put against the involute surface in the normal section at the point of intersection with the reference circle, the corresponding angle is termed normal pressure angle n; this is equal to the pressure angle PO of the tool. The interrelationship with the helix angle at the reference circle is tann = cos tant. On a spur gear n = t. Between the base helix angle b and the helix angle on the reference circle the relationship is sinb = cosn sin. The base diameter db is given by the reference diameter d, by db = d cost. In the case of internal gears, the number of teeth z and thus also the diameters d, db, da, df are negative values. Right flank
Left flank
Tooth trace Reference cylinder Reference circle d da df b h ha hf s e p Reference diameter Tip diameter Root diameter Facewidth Tooth depth Addendum Dedendum Tooth thickness on the reference circle Spacewidth on the reference circle Pitch on the reference circle
(1) (2)
rb = db/2 is the base radius. The angle inv is termed involute function, and the angle =
^
+ inv = tan is termed working angle.
Figure 6 Definitions on the cylindrical gear Developed involute line 1.2.2.2 Pitches The pitch pt of a helical gear (p in the case of a spur gear) lying in a transverse section is the length of the reference circle arc between two successive right or left flanks, see figures 6 and 7. With the number of teeth z results pt = d/z = mt. The normal transverse pitch pet of a helical gear is equal to the pitch on the basic circle pbt, thus pet = pbt = db/z. Hence, in the normal section the normal base pitch at a point pen = pet cosb is resulting from it, and in the axial section the axial pitch pex = pet/tanb, see figure 13. Figure 5 Involute in a transverse section Figure 7 Pitches in the transverse section of a helical gear
Generator Involute of base cylinder Developed base cylinder envelope Figure 4 Base cylinder with involute helicoid and generator
110
111
1.2.2.3 Addendum modification When generating tooth flanks on a cylindrical gear by means of a tooth-rack-like tool (e.g. a hob), a straight pitch line parallel to the datum line of tool rolls off on the reference circle. The distance (x mn) between the straight pitch line and the datum line of tool is the addendum modification, and x is the addendum modification coefficient, see figure 8. An addendum modification is positive, if the datum line of tool is displaced from the reference circle towards the tip, and it is negative if the datum line is displaced towards the root of the gear. This is true for both external and internal gears. In the case of internal gears the tip points to the inside. An addendum modification for external gears should be carried through approximately within the limits as shown in figure 9. The addendum modification limits xmin and xmax are represented dependent on the virtual number of teeth zn = z/(cos cos2b). The upper limit xmax takes into account the intersection circle of the teeth and applies to a normal crest width in the normal section of san = 0.25 mn. When falling below the lower limit xmin this results in an undercut which shortens the usable involute and weakens the tooth root. A positive addendum modification results in a greater tooth root width and thus in an increase in the tooth root carrying capacity. In the case of small numbers of teeth this has a considerably stronger effect than in the case of larger ones. One mostly strives for a greater addendum modification on pinions than on gears in order to achieve equal tooth root carrying capacities for both gears, see figure 19. Further criteria for the determination of addendum modification are contained in /2/, /3/, and /4/. The addendum modification coefficient x refers to gear teeth free of backlash and deviations. In order to take into account tooth thickness deviation As (for backlash and manufacturing tolerances) and machining allowances q (for premachining), one has to give the following generating addendum modification coefficient for the manufacture of a cylindrical gear: XE = x + As q + mn sin n 2mn tan n (3)
Datum line of tool = straight pitch line
1.2.3 Concepts and parameters associated with a cylindrical gear pair 1.2.3.1 Terms The mating of two external cylindrical gears (external gears) gives an external gear pair. In the case of a helical external gear pair one gear has left-handed and the other one right-handed flank direction. The mating of an external cylindrical gear with an internal cylindrical gear (internal gear) gives an internal gear pair. In the case of a helical internal gear pair, both gears have the same flank direction, that is either right-handed or left-handed. The subscript 1 is used for the size of the smaller gear (pinion), and the subscript 2 for the larger gear (wheel or internal gear). In the case of a zero gear pair both gears have as addendum modification coefficient x1 = x2 = 0 (zero gears). In the case of a V-zero gear pair, both gears have addendum modifications (V-gears), that is with x1 + x2 = 0, i.e. x1 = -x2. For a V-gear pair, the sum is not equal to zero, i.e. x1 + x2 0. One of the cylindrical gears in this case may, however, have an addendum modification x = 0. 1.2.3.2 Mating quantities The gear ratio of a gear pair is the ratio of the number of teeth of the gear z2 to the number of teeth of the pinion z1, thus u = z2/z1. Working pitch circles with diameter dw = 2rw are those transverse intersection circles of a cylindrical gear pair, which have the same circumferential speed at their mutual contact point (pitch point C), figure 10. The working pitch circles divide the centre distance a = rw1 + rw2 in the ratio of the tooth numbers, thus dw1 = 2 a/(u + 1) and dw2 = 2 a u/(u +1). In the case of both a zero gear pair and a V-zero gear pair, the centre distance is equal to the zero centre distance ad = (d1 + d2)/2, and the pitch circles are simultaneously the reference circles, i.e. dw = d. However, in the case of a V-gear pair the centre distance is not equal to the zero centre distance, and the pitch circles are not simultaneously the reference circles. If in the case of V-gear pairs the bottom clearance cp corresponding to the standard basic rack tooth profile is to be retained (which is not absolutely necessary), then an addendum modification is to be carried out. The addendum modification factor is k = (a - ad)/mn - (x1 + x2). For zero gear pairs and V-zero gear pairs k = 0. In the case of external gear pairs k < 0, i.e. the tip diameters of both gears become smaller. In the case of internal gear pairs k > 0, i.e. the tip diameters of both gears become larger (on an internal gear with negative tip diameter the
a)
Straight pitch line
b)
Datum line of tool
Straight pitch line
c)
Figure 10 Transverse section of an external gear pair with contacting left-handed flanks absolute value becomes smaller). In a cylindrical gear pair either the left or the right flanks of the teeth contact each other on the line of action. Changing the flanks results in a line of action each lying symmetrical in relation to the centre line through O1O2. The line of action with contacting left flanks in figure 10 is the tangent to the two base circles at points T1 and T2. With the common tangent on the pitch circles it includes the working pressure angle wt. The working pressure angle wt is the transverse pressure angle at a point belonging to the working pitch circle. According to figure 10 it is determined by cos wt = db1/dw1 = db2/dw2. In the case of zero gear pairs and V-zero gear pairs, the working pressure angle is equal to the transverse pressure angle on the reference circle, i.e. wt = t. The length of path of contact g is that part of the line of action which is limited by the two tip circles of the cylindrical gears, figure 11. The starting point A of the length of path of contact is the point at which the line of action intersects the tip circle of the driven gear, and the finishing point E is the point at which the line of action intersects the tip circle of the driving gear.
Figure 8 Different positions of the datum line of tool in relation to the straight pitch line through pitch point C. a) Zero addendum modification; x = 0 b) Negative addendum modification; x < 0 c) Positive addendum modification; x > 0
Figure 9 Addendum modification limit xmax (intersection circle) and xmin (undercut limit) for external gears dependent on the virtual number of teeth zn (for internal gears, see /1/ and /3/).
112
113
Driven
Driven
Line of action
1.2.4 Summary of the most important formulae Tables 2 and 3 contain the most important formulae for the determination of sizes of a cylindrical gear and a cylindrical gear pair, and this for both external and internal gear pairs. The following rules for signs are to be observed: In the case of internal gear pairs the number of teeth z2 of the internal gear is a negative quantity. Thus, also the centre distance a or ad and the gear ratio u as well as the diameters d2, da2, db2, df2, dw2 and the virtual number of teeth zn2 are negative. When designing a cylindrical gear pair for a gear stage, from the output quantities of tables 2 and 3 only the normal pressure angle n and the gear ratio u are given, as a rule. The number of teeth of
the pinion is determined with regard to silent running and a balanced foot and flank load carrying capacity, at approx. z1 = 18 ... 23. If a high foot load carrying capacity is required, the number may be reduced to z1 = 10. For the helix angle, = 10 up to 15 degree is given, in exceptional cases also up to 30 degree. The addendum modification limits as shown in figure 9 are to be observed. On the pinion, the addendum modification coefficient should be within the range of x1 = 0.2 to 0.6 and from IuI > 2 the width within the range b1 = (0.35 to 0.45) a. Centre distance a is determined either by the required power to be transmitted or by the constructional conditions.
Driving Line of action Figure 11 Length of path of contact AE in the transverse section of an external gear pair A Starting point of engagement E Finishing point of engagement C Pitch point 1.2.3.3 Contact ratios The transverse contact ratio in the transverse section is the ratio of the length of path of contact g to the normal transverse pitch pet, i.e. = g/pet, see figure 12. In the case of spur gear pairs, the transverse contact ratio gives the average number of pairs of teeth meshing during the time of contact of a tooth pair. According to figure 12, the left-hand tooth pair is in the individual point of contact D while the right-hand tooth pair gets into mesh at the starting point of engagement A. The righthand tooth pair is in the individual point of contact B when the left-hand tooth pair leaves the mesh at the finishing point of engagement E. Along the individual length of path of contact BD one tooth pair is in mesh, and along the double lengths of paths of contact AB and DE two pairs of teeth are simultaneously in mesh. In the case of helical gear pairs it is possible to achieve that always two or more pairs of teeth are in mesh simultaneously. The overlap ratio gives the contact ratio, owing to the helix of the teeth, as the ratio of the facewidth b to the axial pitch pex, i.e. = b/pex, see figure 13. The total contact ratio is the sum of transverse contact ratio and overlap ratio, i.e. = + . With an increasing total contact ratio, the load carrying capacity increases, as a rule, while the generation of noise is reduced.
Driving
Figure 12 Single and double contact region in the transverse section of an external gear pair B, D Individual points of contact A, E Starting and finishing point of engagement, respectively C Pitch point
Length of path of contact Figure 13 Pitches in the plane of action A Starting point of engagement E Finishing point of engagement
114
115
Table 2 Parameters for a cylindrical gear *) Output quantities: mm mn degree n degree z x xE mm haPO Item normal module normal pressure angle reference helix angle number of teeth *) addendum modification coefficient generating addendum modification coefficient, see equation (3) addendum of the tool Formula mt = mn cos tann cos
Table 3 Parameters for a cylindrical gear pair *)
Output quantities: The parameters for pinion and wheel according to table 2 must be given, further the facewidths b1 and b2, as well as either the centre distance a or the sum of the addendum modification coefficients x1 + x2.
Item
Formula u= z2 z1 mt (z1 + z2) cost 2a z 1 + z2 (invwt invt) 2 tann x1 + x2 tann + invt z1 + z2
Transverse module Transverse pressure angle Base helix angle Reference diameter Tip diameter (k see table 3) Root diameter Base diameter Transverse pitch Transverse pitch on path of contact; Transverse base pitch Transverse pressure angle at tip circle Transverse tooth thickness on the pitch circle Normal tooth thickness on the pitch circle Transverse tooth thickness on the addendum circle Virtual number of teeth
Gear ratio Working transverse pressure angle (a given) Sum of the addendum modification coefficients (a given) Working transverse pressure angle (x1 + x2 given) Centre distance (x1 + x2 given) Reference centre distance Addendum modification factor **) Working pitch circle diameter of the pinion Working pitch circle diameter of the gear Length of path of contact Transverse contact ratio Overlap ratio Total contact ratio
tant =
coswt = x1 + x2 =
sinb = sin cosn d = mt z da = d + 2 mn (1 + x + k) df = d 2 (haPO mn xE) db = d cos t pt = d z = mt db = pt cost z
invwt = 2 a= ad = k=
cost mt (z1 + z2) coswt 2 mt (z1 + z2) 2
a ad (x1 + x2) mn cost 2a = d1 coswt u+1 cost 2au = d2 coswt u+1 1 2
dw1 = dw2 = g =
pet = pbt =
d cos at = b da st = mt ( + 2 x tann) 2
da12 db12 +
u
IuI
da22 db22
) asinwt
= =
g pet b tanb pet b = min (b1, b2)
sn = st cos sat = da zn =
( dt
+ invt invat)
**)
= +
z cos cos2b **) For inv, see equation (1).
*) For internal gear pairs, z2 and a are to be used as negative quantities. **) See subsection 1.2.3.2.
*) For an internal gear, z is to be used as a negative quantity.
116
117
Cylindrical Gear Units Geometry of Involute Gears Load Carrying Capacity of Involute Gears
facewidth are achieved. This has to be taken into consideration especially in the case of checks of contact patterns carried out under low loads. Under partial load, however, the local maximum load rise is always lower than the theoretical uniform load distribution under full load. In the case of modified gear teeth, the contact ratio is reduced under partial load because of incomplete carrying portions, making the noise generating levels increase in the lower part load range. With increasing load, the carrying portions and thus the contact ratio increase so that the generating levels drop. Gear pairs which are only slightly loaded do not require any modification. ting into engagement, and a load reduction on the tooth leaving the engagement. In the case of longitudinal correction, the tooth trace relief often is superposed by a symmetric longitudinal Profile correction crowning. With it, uniform load carrying along the face width and a reduction in load concentration at the tooth ends during axial displacements is attained. Longitudinal correction
1.2.5 Tooth corrections The parameters given in the above subsections 1.2.1 to 1.2.4 refer to non-deviating cylindrical gears. Because of the high-tensile gear materials, however, a high load utilization of the gear units is possible. Noticeable deformations of the elastic gear unit components result from it. The deflection at the tooth tips is, as a rule, a multiple of the manufacturing form errors. This leads to meshing interferences at the entering and leaving sides, see figure 14. There is a negative effect on the load carrying capacity and generation of noise.
Line of action Pinion
Wheel
Figure 16 Tooth corrections designed for removing local load increases due to deformations under nominal load Bending Torsion Manufacturing deviation Bearing deformation Housing deformation Running-in wear Effective tooth trace deviation F = f-y Load distribution across the facewidth w 1.3 Load carrying capacity of involute gears 1.3.1 Scope of application and purpose The calculation of the load carrying capacity of cylindrical gears is generally carried out in accordance with the calculation method according to DIN 3990 /8/ (identical with ISO 6336) which takes into account pitting, tooth root bending stress and scoring as load carrying limits. Because of the relatively large scope of standards, the calculation in accordance with this method may be carried out only by using EDP programs. As a rule, gear unit manufacturers have such a tool at hand. The standard work is the FVA-Stirnradprogramm /9/ which includes further calculation methods, for instance, according to Niemann, AGMA, British Standard, and other. In DIN 3990, different methods A, B, C ... are suggested for the determination of individual factors, where method A is more exact but also more time-consuming than method B, etc. The application standard /10/ according to DIN 3990 is based on simplified methods. Because of its - even though limited - universal validity it still is relatively time-consuming. The following calculation method for pitting resistance and tooth strength of case-hardened cylindrical gears is a further simplification if compared with the application standard, however, without losing some of its meaning. Certain conditions must be adhered to in order to attain high load carrying capacities which also results in preventing scuffing. Therefore, a calculation of load carrying capacity for scuffing will not be considered in the following. It has to be expressly emphasized that for the load carrying capacity of gear units the exact calculation method - compared with the simplified one - is always more meaningful and therefore is exclusively decisive in borderline cases. Design, selection of material, manufacture, heat treatment and operation of industrial gear units are subject to certain rules which lead to a long service life of the cylindrical gears. Those rules are: Gear teeth geometry acc. to DIN 3960; Cylindrical gears out of case-hardened steel; Tooth flanks in DIN quality 6 or better, fine machined; Quality of material and heat treatment proved by quality inspections acc. to DIN 3990 /11/; Effective case depth after carburizing according to instructions /12/ with surface hardnesses of 58 ... 62 HRC; Gears with required tooth corrections and without harmful notches in the tooth root; Gear unit designed for fatigue strength, i.e. life factors ZNT = YNT = 1.0; Flank fatigue strength Hlim y 1,200 N/mm2; Subcritical operating range, i.e. pitch circle velocity lower than approx. 35 m/s; Sufficient supply of lubricating oil; Use of prescribed gear oils with sufficient scuffing load capacity (criteria stage 12) and grey staining load capacity (criteria stage 10); Maximum operating temperature 95 C.
Figure 14 Cylindrical gear pair under load 1 Driving gear 2 Driven gear a, b Tooth pair being in engagement c, d Tooth pair getting into engagement Further, the load causes bending and twisting of pinion and wheel shaft, pinion and wheel body, as well as settling of bearings, and housing deformations. This results in skewing of the tooth flanks which often amounts considerably higher than the tooth trace deviations caused by manufacture, see figure 15. Non-uniform load carrying occurs along the face width which also has a negative effect on the load carrying capacity and generation of noise. The running-in wear of case hardened gears amounts to a few micrometers only and cannot compensate the mentioned deviations. In order to restore the high load carrying capacity of case hardened gears and reduce the generation of noise, intentional deviations from the involute (profile correction) and from the theoretical tooth trace (longitudinal correction) are produced in order to attain nearly ideal geometries with uniform load distribution under load again. The load-related form corrections are calculated and made for one load only - as a rule for 70 ... 100% of the permanently acting nominal load /5, 6, 7/. At low partial load, contact patterns which do not cover the entire tooth depth and
Figure 15 Deformations and manufacturing deviations on a gear unit shaft
In figure 16, usual profile and longitudinal corrections are illustrated. In the case of profile correction, the flanks on pinion and wheel are relieved at the tips by an amount equal to the length they are protruding at the entering and leaving sides due to the bending deflection of the teeth. Root relief may be applied instead of tip relief which, however, is much more expensive. Thus, a gradual load increase is achieved on the tooth get-
118
119
Cylindrical Gear Units Load Carrying Capacity of Involute Gears
If these requirements are met, a number of factors can be definitely given for the calculation of the load carrying capacity according to DIN 3990, so that the calculation procedure is partly considerably simplified. Non-observance of the above requirements, however, does not necessarily mean that the load carrying capacity is reduced. In case of doubt one should, however, carry out the calculation in accordance with the more exact method.
1.3.2 Basic details The calculation of the load carrying capacity is based on the nominal torque of the driven machine. Alternatively, one can also start from the nominal torque of the prime mover if this corresponds with the torque requirement of the driven machine. In order to be able to carry out the calculation for a cylindrical gear stage, the details listed in table 4 must be given in the units mentioned in the table. The geometric quantities are calculated according to tables 2 and 3. Usually, they are contained in the workshop drawings for cylindrical gears.
In the further course of the calculation, the quantities listed in table 5 are required. They are derived from the basic details according to table 4. Table 5 Derived quantities Designation Relation Unit
Gear ratio Reference diameter of the pinion Transverse tangential force at pinion reference circle Circumferential speed at reference circle Base helix angle Virtual number of teeth of the pinion Virtual number of teeth of the wheel Transverse module
u = z2/z1 d1 = z1 mn/cos Ft = 19.1 S 106 P/(d1 n1) v = d1 n1/60 000 b = arc sin(cosn sin) zn1 = z1 / (cos cos2b) zn2 = z2 / (cos cos2b) mt = mn / cos t = arc tan (tann / cos) wt = arc cos [(z1 + z2) mt cost / (2a)] pet = mt cost db1 = z1mt cost db2 = z2mt cost g = 1 2
mm
Table 4 Basic details Abbreviation P n1 a mn da1 da2 b1 b2 z1 z2 x1 x2 n V40 Rz1 Rz2 Meaning Power rating Pinion speed Centre distance Normal module Tip diameter of the pinion Tip diameter of the wheel Facewidth of the pinion Facewidth of the wheel Number of teeth of the pinion Number of teeth of the wheel Addendum modification coefficient of the pinion Addendum modification coefficient of the wheel Normal pressure angle Reference helix angle Kinematic viscosity of lubricating oil at 40 C Peak-to-valley height on pinion flank Peak-to-valley height on wheel flank Unit kW 1/min mm mm mm mm
m/s
Degree
mm Degree
mm mm Transverse pitch Degree Degree Length of path of contact cSt m m Transverse contact ratio Overlap ratio Base diameter of the pinion Base diameter of the wheel mm mm mm u
IuI
Transverse pressure angle Working transverse pressure angle
Degree
da12 db12 +
da22 db22
) asinwt
mm
= g / pet = b tanb / pet b = min (b1, b2)
120
121
1.3.3 General factors 1.3.3.1 Application factor With the application factor KA, all additional forces acting on the gears from external sources are taken into consideration. It is dependent on the characteristics of the driving and driven machines, as well as the couplings, the masses and stiffness of the system, and the operating conditions.
The application factor is determined by the service classification of the individual gear. If possible, the factor KA should be determined by means of a careful measurement or a comprehensive analysis of the system. Since very often it is not possible to carry out the one or other method without great expenditure, reference values are given in table 6 which equally apply to all gears in a gear unit.
1.3.4 Tooth flank load carrying capacity The calculation of surface durability against pitting is based on the Hertzian pressure at the pitch circle. For pinion and wheel the same effective Hertzian pressure H is assumed. It must not exceed the permissible Hertzian pressure Hp, i.e. H ) Hp. H = ZE ZH Z Z
1.3.4.1 Effective Hertzian pressure The effective Hertzian pressure is dependent on the load, and for pinion and wheel is equally derived from the equation
KA Kv KH KH
u + 1 Ft u d1 b
(8)
Table 6 Application factor KA Working mode of the driven machine Working mode of prime mover Uniform Moderate shock loads Average shock loads Heavy shock loads Uniform 1.00 1.10 1.25 1.50 Moderate shock loads 1.25 1.35 1.50 1.75 Average shock loads 1.50 1.60 1.75 2.00 Heavy shock loads 1.75 1.85 2.00 or higher 2.25 or higher H Effective Hertzian pressure in N/mm2 Further: b is the smallest facewidth b1 or b2 of pinion or wheel acc. to table 4 Ft, u, d1 acc. to table 5 KA Application factor acc. to table 6 KV Dynamic factor acc. to equation (4) KH Face load factor acc. to equ. (5) KH Transverse load factor acc. to equ. (7) 2 ZE Elasticity factor; ZE = 190 N/mm for gears out of steel ZH Zone factor acc. to figure 17 Z Helix angle factor acc. to equ. (9) Z Contact ratio factor acc. to equ. (10) or (11) With according to table 4 applies: Z = cos (9)
1.3.3.2 Dynamic factor With the dynamic factor KV, additional dynamic forces caused in the meshing itself are taken into consideration. Taking z1, v and u from tables 4 and 5, it is calculated from Kv = 1 + 0.0003 z1 v u2 1 + u2 (4)
1.3.3.3 Face load factor The face load factor KH takes into account the increase in the load on the tooth flanks caused by non-uniform load distribution over the facewidth. According to /8/, it can be determined by means of different methods. Exact methods based on comprehensive measurements or calculations or on a combination of both are very expensive. Simple methods, however, are not exact, as a consequence of which estimations made to be on the safe side mostly result in higher factors. For normal cylindrical gear teeth without longitudinal correction, the face load factor can be calculated according to method D in accordance with /8/ dependent on facewidth b and reference diameter d1 of the pinion, as follows: KH = 1.15 + 0.18 (b/d1)2 + 0.0003 b (5)
attain uniform load carrying over the facewidth, see subsection 1.2.5. Under such conditions, the face load factor lies within the range of KH = 1.1 ... 1.25. As a rough rule applies: A sensibly selected crowning symmetrical in length reduces the amount of KH lying above 1.0 by approx. 40 to 50%, and a directly made longitudinal correction by approx. 60 to 70%. In the case of slim shafts with gears arranged on one side, or in the case of lateral forces or moments acting on the shafts from external sources, for the face load factors for gears without longitudinal correction the values may lie between 1.5 and 2.0 and in extreme cases even at 2.5. Face load factor KF for the determination of increased tooth root stress can approximately be deduced from face load factor KH according to the relation KF = (KH )0.9 (6)
With and according to table 5 applies: Z = 4 (1 ) + for < 1 (10) 3
Z =
for + 1
(11)
Figure 17 Zone factor ZH depending on helix angle as well as on the numbers of teeth z1, z2, and addendum modification coefficients x1, x2; see table 4.
with b = min (b1, b2). As a rule, the gear unit manufacturer carries out an analysis of the load distribution over the facewidth in accordance with an exact calculation method /13/. If required, he makes longitudinal corrections in order to
1.3.3.4 Transverse load factors The transverse load factors KH and KF take into account the effect of the non-uniform distribution of load between several pairs of simultaneously contacting gear teeth. Under the conditions as laid down in subsection 1.3.1, the result for surface stress and for tooth root stress according to method B in accordance with /8/ is KH = KF = 1.0 (7)
1.3.4.2 Permissible Hertzian pressure The permissible Hertzian pressure is determined by HP = ZL Zv ZX ZR ZW Hlim SH (12)
ZL, Zv, ZR, ZW and ZX are the same for pinion and wheel and are determined in the following. The lubricant factor is computed from the lubricating oil viscosity V40 according to table 4 using the following formula: ZL = 0.91 + 0.25 (1 + 112 ) 2 V40 (13)
HP permissible Hertzian pressure in N/mm2. It is of different size for pinion and wheel if the strengths of materials Hlim are different. Factors
122
123
For the speed factor, the following applies using the circumferential speed v according to table 5: Zv = 0.93 + 0.157 40 1+ v (14)
degree
The roughness factor can be determined as a function of the mean peak-to-valley height RZ = (RZ1 + RZ2)/2 of the gear pair as well as the gear ratio u and the reference diameter d1 of the pinion, see tables 4 and 5, from
Flank hardness HV1
ZR =
[ 0.513 R
z
(1 + IuI) d1
0.08
(15)
For a gear pair with the same tooth flank hardness on pinion and wheel, the work hardening factor is
ZW = 1.0
(16)
Figure 18 Allowable stress number for contact stress Hlim of alloyed case hardening steels, case hardened, depending on the surface hardness HV1 of the tooth flanks and the material quality. ML modest demands on the material quality MQ normal demands on the material quality ME high demands on the material quality, see /11/ 1.3.5.1 Effective tooth root stress As a rule, the load-dependent tooth root stresses for pinion and wheel are different. They are calculated from the following equation: sF = Y Y YFS KA Kv KF KF Ft b mn
degree
The size factor is computed from module mn according to table 4 using the following formula:
ZX = 1.05 0.005 mn
(17)
(18)
with the restriction 0.9 x ZX x 1. Hlim Endurance strength of the gear material. For gears made out of case hardening steel, case hardened, figure 18 shows a range from 1300 ... 1650 N/mm2 depending on the surface hardness of the tooth flanks and the quality of the material. Under the conditions as described in subsection 1.3.1, material quality MQ may be selected for pinion and wheel, see table on page 97. SH required safety factor against pitting, see subsection 1.3.6.
F Effective tooth root stress in N/mm2 The following factors are of equal size for pinion and wheel: mn, Ft acc. to tables 4 and 5 Application factor acc. to table 6 KA KV Dynamic factor acc. to equation (4) Face load factor acc. to equation (6) KF Transverse load factor acc. to equ. (7) KF Y Contact ratio factor acc. to equ. (19) Helix angle factor acc. to equ. (20) Y The following factors are of different size for pinion and wheel: b1, b2 Facewidths of pinion and wheel acc. to table 4. If the facewidths of pinion and wheel are different, it may be assumed that the load bearing width of the wider facewidth is equal to the smaller facewidth plus such extension of the wider that does not exceed one times the module at each end of the teeth.
degree
1.3.5 Tooth strength The maximum load in the root fillet at the 30-degree tangent is the basis for rating the tooth strength. For pinion and wheel it shall be shown separately that the effective tooth root stress F does not exceed the permissible tooth root stress FP, i.e. F < FP.
Figure 19 Tip factor YFS for external gears with standard basic rack tooth profile acc. to DIN 867 depending on the number of teeth z (or zn in case of helical gears) and addendum modification coefficient x, see tables 4 and 5. The following only approximately applies to internal gears: YFS = YFS ( value for x = 1.0 and z = 300).
124
125
Cylindrical Gear Units Load Carrying Capacity of Involute Gears Gear Unit Types
flanks and the material quality. Under the conditions according to subsection 1.3.1, a strength pertaining to quality MQ may be used as a basis for pinion and wheel see table on page 97. SF Safety factor required against tooth breakage, see subsection 1.3.6. helix angle = 10 degree; kinematic viscosity of the lubricating oil V40 = 320 cSt; mean peak-tovalley roughness Rz1 = Rz2 = 4.8 m. The cylindrical gears are made out of the material 17 CrNiMo 6. They are case hardened and ground with profile corrections and width-symmetrical crowning. Calculation (values partly rounded): Gear ratio u = 1.88; reference diameter of the pinion d1 = 558.485 mm; nominal circumferential force on the reference circle Ft = 800,425 N; circumferential speed on the reference circle v = 4.123 m/s; base helix angle b = 9.391 degree; virtual numbers of teeth zn1 = 26.08 and zn2 = 49.03; transverse module mt = 22.339 mm; transverse pressure angle t = 20.284 degree; working transverse pressure angle wt = 22.244 degree; normal transverse pitch pet = 65.829; base diameters db1 = 523.852 mm and db2 = 984.842 mm; length of path of contact g = 98.041 mm; transverse contact ratio = 1.489; overlap ratio = 0.879. Application factor KA = 1.50 (electric motor with uniform mode of operation, coal mill with medium shock load); dynamic factor KV = 1.027; face load factor KH = 1.20 [acc. to equation (5) follows KH = 1.326, however, because of symmetrical crowning the calculation may be made with a smaller value]; KF = 1.178; KH = KF = 1.0. Load carrying capacity of the tooth flanks: Elasticity factor ZE = 190 N mm 2; zone factor ZH = 2.342; helix angle factor Z = 0.992; contact ratio factor Z = 0.832. According to equation (8), the Hertzian pressure for pinion and wheel is H = 1251 N/mm2. Lubricant factor ZL = 1.047; speed factor ZV = 0.978; roughness factor ZR = 1.018; work hardening factor ZW = 1.0; size factor ZX = 0.94. With the allowable stress number for contact stress (pitting) Hlim = 1500 N/mm2, first the permissible Hertzian pressure HP = 1470 N/mm2 is determined from equation (12) without taking into account the safety factor. The safety factor against pitting is found by SH = HP/H = 1470/1251 = 1.18. The safety factor referring to the torque is SH2 = 1.38. Load carrying capacity of the tooth root: Contact ratio factor Y = 0.738; helix angle factor Y = 0.927; tip factors YFS1 = 4.28 and YFS2 = 4.18 (for ha0 = 1.4 mn; a0 = 0.3 mn; pro = 10 degree; prO = 0.0205 mn). The effective tooth root stresses F1 = 537 N/mm2 for the pinion and F2 = 540 N/mm2 for the wheel can be obtained from equation (18). Stress correction factor YST = 2.0; relative sensitivity factor YrelT = 1.0; relative surface factor YRelT = 0.96; size factor YX = 0.83. Without taking into consideration the safety factor, the permissible tooth root stresses for pinion and wheel FP1 = FP2 = 797 N/mm2 can be obtained from equation (21) with the bending stress number Flim = 500 N/mm2. The safety factors against tooth breakage referring to the torque are SF = FP/F: for the pinion SF1 = 797/537 = 1.48 and for the wheel SF2 = 797/540 = 1.48. 1.4 Gear unit types 1.4.1 Standard designs In the industrial practice, different types of gear units are used. Preferably, standard helical and bevel-helical gear units with fixed transmission ratio and size gradation are applied. These single-stage to four-stage gear units according to the modular construction system cover a wide range of speeds and torques required by the driven machines. Combined with a standard electric motor such gear units are, as a rule, the most economical drive solution. But there are also cases where no standard drives are used. Among others, this is true for high torques above the range of standard gear units. In such cases, special design gear units are used, load sharing gear units playing an important role there. 1.4.2 Load sharing gear units In principle, the highest output torques of gear units are limited by the manufacturing facilities, since gear cutting machines can make gears up to a maximum diameter only. Then, the output torque can be increased further only by means of load sharing in the gear unit. Load sharing gear units are, however, also widely used for lower torques as they provide certain advantages in spite of the larger number of internal components, among others they are also used in standard design. Some typical features of the one or other type are described in the following. 1.4.3 Comparisons In the following, single-stage and two-stage gear units up to a ratio of i = 16 are examined. For common gear units the last or the last and the last but one gear stage usually come to approx. 70 to 80% of the total weight and also of the manufacturing expenditure. Adding further gear stages in order to achieve higher transmission ratios thus does not change anything about the following fundamental description. In figure 21, gear units without and with load sharing are shown, shaft 1 each being the HSS and shaft 2 being the LSS. With speeds n1 and n2, the transmission ratio can be obtained from the formula i = n1 / n2 (24)
YFS1, YFS2 Tip factors acc. to figure 19. They account for the complex stress condition inclusive of the notch effect in the root fillet. With the helix angle acc. to table 4 and the overlap ratio acc. to table 5 follows: Y = 0.25 + 0.75 cos2 (19)
with the restriction 0.625 ) Y ) 1 Y = 1 120 (20)
with the restriction Y + max [(1 - 0.25 ); (1 /120)]. 1.3.5.2 Permissible tooth root stress The permissible tooth root stress for pinion and wheel is determined by FP = YST YrelT YRrelT YX Flim (SF) (21)
Flank hardness HV1
FP permissible tooth root stress in N/mm2. It is not equal for pinion and wheel if the material strengths Flim are not equal. Factors YST, YrelT, YRrelT and YX may be approximately equal for pinion and wheel. is the stress correction factor of the reference test gears for the determination of the bending stress number Flim. For standard reference test gears, YST = 2.0 has been fixed in the standard. YrelT is the notch relative sensitivity factor (notch sensitivity of the material) referring to the standard reference test gear. By approximation YrelT = 1.0. YST For the relative surface factor (surface roughness factor of the tooth root fillet) referring to the standard reference test gear the following applies by approximation, depending on module mn : mn ) 8 mm YRrelT = 1.00 for = 0.98 for 8 mm < mn ) 16 mm (22) = 0.96 for mn > 16 mm and for the size factor YX = 1.05 0.01 mn (23) with the restriction 0.8 ) YX ) 1. Flim Bending stress number of the gear material. For gears out of case hardening steel, case hardened, a range from 310 ... 520 N/mm2 is shown in figure 20 depending on the surface hardness of the tooth
Figure 20 Bending stress number Flim of alloyed case hardening steel, case hardened, depending on the surface hardness HV1 of the tooth flanks and the material quality. ML modest demands on the material quality MQ normal demands on the material quality ME high demands on the material quality, see /11/ 1.3.6 Safety factors The minimum required safety factors according to DIN are: against pitting SH = 1.0 against tooth breakage SF = 1.3. In practice, higher safety factors are usual. For multistage gear units, the safety factors are determined about 10 to 20% higher for the expensive final stages, and in most cases even higher for the cheaper preliminary stages. Also for risky applications a higher safety factor is given. 1.3.7 Calculation example An electric motor drives a coal mill via a multistage cylindrical gear unit. The low speed gear stage is to be calculated. Given: Nominal power rating P = 3300 kW; pinion speed n1 = 141 1/min.; centre distance a = 815 mm; normal module mn = 22 mm; tip diameter da1 = 615.5 mm and da2 = 1100 mm; pinion and wheel widths b1 = 360 mm and b2 = 350 mm; numbers of teeth z1 = 25 and z2 = 47; addendum modification coefficients x1 = 0.310 and x2 = 0.203; normal pressure angle n = 20 degree;
126
127
Cylindrical Gear Units Gear Unit Types
The diameter ratios of the gears shown in figure 21 correspond to the transmission ratio i = 7. The gear units have the same output torques, so that in figure 21 a size comparison to scale is illustrated. Gear units A, B, and C are with offset shaft arrangement, and gear units D, E, F, and G with coaxial shaft arrangement.
In gear unit D the load of the high-speed gear stage is equally shared between three intermediate gears which is achieved by the radial movability of the sun gear on shaft 1. In the low-speed gear stage the load is shared six times altogether by means of the double helical teeth and the axial movability of the intermediate shaft. In order to achieve equal load distribution between the three intermediate gears of gear units E, F, and G the sun gear on shaft 1 mostly is radially movable. The large internal gear is an annulus gear which in the case of gear unit E is connected with shaft 2, and in the case of gear units F and G with the housing. In gear units F and G, web and shaft 2 form an integrated whole. The idler gears rotate as planets around the central axle. In gear unit G, double helical teeth and axial movability of the idler gears guarantee equal load distribution between six branches. 1.4.3.1 Load value By means of load value BL, it is possible to compare cylindrical gear units with different ultimate stress values of the gear materials with each other in the following examinations. According to /14/, the load value is the tooth peripheral force Fu referred to the pinion pitch diameter dw and the carrying facewidth b, i.e. BL = Fu b dw (25)
1.4.3.2 Referred torques In figure 22, referred torques for the gear units shown in figure 21 are represented, dependent on the transmission ratio i. Further explanations are given in table 7. The torque T2 is referred to the construction dimension D when comparing the sizes, to the weight of the gear unit G when comparing the weights, and to the generated Table 7 Referred Torques Comparison criteria Size Weight Gear teeth surface Definition = = = T2 D3 BL T2 G BL T2 A3/2 BL
surface A of the pitch circle cylinders when comparing the gear teeth surfaces. Gear unit weight G and gear teeth surface A (= generated surface) are one measure for the manufacturing cost. The higher a curve, in figure 22, the better the respective gear unit in comparison with the others.
Dimension m mm m mm2 kg mm2 m2
Units of the basic details T2 in mm BL in N/mm2 D in mm G in kg A in m2
The permissible load values of the meshings of the cylindrical gear units can be computed from the pitting resistance by approximation, as shown in /15/ (see section 1.3.4), using the following formula: Figure 21 Diagrammatic view of cylindrical gear unit types without and with load sharing. Transmission ratio i = 7. Size comparison to scale of gear units with the same output torque. BL 7 . 10-6 u u+1 2Hlim KA SH2 (26)
Ratio i a) Torque referred to size
Ratio i b) Torque referred to gear unit weight
Gear unit A has one stage, gear unit B has two stages. Both gear units are without load sharing. Gear units C, D, E, F, and G have two stages and are load sharing. The idler gears in gear units C and D have different diameters. In gear units E, F, and G the idler gears of one shaft have been joined to one gear so that they are also considered to be single-stage gear units. Gear unit C has double load sharing. Uniform load distribution is achieved in the high-speed gear stage by double helical teeth and the axial movability of shaft 1.
with BL in N/mm2 and allowable stress number for contact stress (pitting) Hlim in N/mm2 as well as gear ratio u, application factor KA and factor of safety from pitting SH. The value of the gear ratio u is always greater than 1, and is negative for internal gear pairs (see table 3). Load value BL is a specific quantity and independent of the size of the cylindrical gear unit. The following applies for practically executed gear units: cylindrical gears out of case hardening steel BL = 4...6 N/mm2; cylindrical gears out of quenched and tempered steel BL = 1...1.5 N/mm2; planetary gear stages with annulus gears out of quenched and tempered steel, planet gears and sun gears out of case hardening steel BL = 2.0...3.5 N/mm2.
Ratio i c) Torque referred to gear teeth surface
Ratio i d) Full-load efficiency
Figure 22 Comparisons of cylindrical gear unit types in figure 21 dependent on the transmission ratio i. Explanations are given in table 7 as well as in the text.
128
129
Cylindrical Gear Units Noise Emitted by Gear Units
For all gear units explained in figures 21 and 22, the same prerequisites are valid. For all gear units, the construction dimension D is larger than the sum of the pitch diameters by the factor 1.15. Similar definitions are valid for gear unit height and width. Also the wall thickness of the housing is in a fixed relation to the construction dimension D /15/. With a given torque T2 and with a load value BL computed according to equation (26), the construction dimension D, the gear unit weight G, and the gear teeth surface A can be determined by approximation by figure 22 for a given transmission ratio i. However, the weights of modular-type gear units are usually higher, since the housing dimensions are determined according to different points of view. Referred to size and weight, planetary gear units F and G have the highest torques at small ratios i. For ratios i < 4, the planetary gear becomes the pinion instead of the sun gear. Space requirement and load carrying capacity of the planetary gear bearings decrease considerably. Usually, the planetary gear bearings are arranged in the planet carrier for ratio i < 4.5. Gear units C and D, which have only external gears, have the highest torque referred to size and weight for ratios above i 7. For planetary gear units, the torque referred to the gear teeth surface is more favourable only in case of small ratios, if compared with other gear units. It is to be taken into consideration, however, that internal gears require higher manufacturing expenditure than external gears for the same quality of manufacture. The comparisons show that there is no optimal gear unit available which combines all advantages over the entire transmission ratio range. Thus, the output torque referred to size and weight is the most favourable for the planetary gear unit, and this all the more, the smaller the transmission ratio in the planetary gear stage. With increasing ratio, however, the referred torque decreases considerably. For ratios above i = 8, load sharing gear units having external gears only are more favourable because with increasing ratio the referred torque decreases only slightly. With regard to the gear teeth surface, planetary gear units do not have such big advantages if compared to load sharing gear units having external gears only. 1.4.3.3 Efficiencies When comparing the efficiency, figure 22d, only the power losses in the meshings are taken into consideration. Under full load, they come to approx. 85% of the total power loss for common cylindrical gear units with rolling bearings. The efficiency as a quantity of energy losses results
from the following relation with the input power at shaft 1 and the torques T1 and T2 h) 1 i
All gear units shown in figure 21 are based on the same coefficient of friction of tooth profile z = 0.06. Furthermore, gears without addendum modification and numbers of teeth of the pinion z = 17 are uniformly assumed for all gear units /15/, so that a comparison is possible. The single stage gear unit A has the best efficiency. The efficiencies of the two stage gear units B, C, D, E, F, and G are lower because the power flow passes two meshings. The internal gear pairs in gear units E, F, and G show better efficiencies owing to lower sliding velocities in the meshings compared to gear units B, C, and D which only have external gear pairs. The lossfree coupling performance of planetary gear units F and G results in a further improvement of the efficiency. It is therefore higher than that of other comparable load sharing gear units. For higher transmission ratios, however, more planetary gear stages are to be arranged in series so that the advantage of a better efficiency compared to gear units B, C, and D is lost. 1.4.3.4 Example Given: Two planetary gear stages of type F arranged in series, total transmission ratio i = 20, output torque T2 = 3 . 106 Nm, load value BL = 2.3 N/mm2. A minimum of weight is approximately achieved by a transmission ratio division of i = 5 . 4 of the HS and LS stage. At 1 = 30 m mm2/kg and 2 = 45 m mm2/kg according to figure 22b, the weight for the HS stage is approximately 10.9 t and for the LS stage approximately 30 t, which is a total 40.9 t. The total efficiency according to figure 22d is = 0.986 . 0.985 = 0.971. In comparison to a gear unit of type D with the same transmission ratio i = 20 and the same output torque T2 = 3 . 106 Nm, however, with a better load value BL = 4 N/mm2 this gear unit has a weight of 68.2 t according to figure 22 with = 11 m mm2/kg and is thus heavier by 67%. The advantage is a better efficiency of = 0.98. The two planetary gear stages of type F together have a power loss which is by 45% higher than that of the gear unit of type D. In addition, there is not enough space for the rolling bearings of the planet gears in the stage with i = 4.
Level correction (dB)
+T + T
2
(27)
Correction curve A
Frequency (Hz) Figure 23 Correction curve according to DIN 45635 /16/ for the A-weighted sound power level or sound pressure level 1.5 Noise emitted by gear units 1.5.1 Definitions Noise emitted by a gear unit - like all other noises - is composed of tones having different frequencies f. Measure of intensity is the sound pressure p which is the difference between the highest (or lowest) and the mean pressure in a sound wave detected by the human ear. The sound pressure can be determined for a single frequency or - as a combination - for a frequency range (single-number rating). It is dependent on the distance to the source of sound. In general, no absolute values are used but amplification or level quantities in bel (B) or decibel (dB). Reference value is, for instance, the sound pressure at a threshold of audibility po = 2 . 10 -5 N/m2. In order to take into consideration the different sensitivities of the human ear at different frequencies, the physical sound pressure value at the different frequencies is corrected according to rating curve A, see figure 23. Apart from sound pressures at certain places, sound powers and sound intensities of a whole system can be determined. From the gear unit power a very small part is turned into sound power. This mainly occurs in the meshings, but also on bearings, fan blades, or by oil movements. The sound power is transmitted from the sources to the outside gear unit surfaces mainly by structure-borne noise (material vibrations). From the outside surfaces, air borne noise is emitted. The sound power LWA is the A-weighted sound power emitted from the source of sound and thus a quantity independent of the distance. The sound power can be converted to an average sound pressure for a certain place. The sound pressure decreases with increasing distance from the source of sound. The sound intensity is the flux of sound power through a unit area normal to the direction of propagation. For a point source of sound it results from the sound power LW divided by the spherical enveloping surface 4 r2, concentrically enveloping the source of sound. Like the sound pressure, the sound intensity is dependent on the distance to the source of sound, however, unlike the sound pressure it is a directional quantity. The recording instrument stores the sound pressure or sound intensity over a certain period of time and writes the dB values in frequency ranges (bands) into the spectrum (system of coordinates). Very small frequency ranges, e.g. 10 Hz or 1/12 octaves are termed narrow bands, see figure 24.
130
131
range) is a single-number rating. The total level is the common logical value for gear unit noises. The pressure level is valid for a certain distance, in general 1 m from the housing surface as an ideal parallelepiped.
(Frequency)
Figure 24 Narrow band frequency spectrum for LpA (A-weighted sound pressure level) at a distance of 1 m from a gear unit.
Histograms occur in the one-third octave spectrum and in the octave spectrum, see figures 25 and 26. In the one-third octave spectrum (spectrum with 1/3 octaves), the bandwidth results from
1.5.2 Measurements The main noise emission parameter is the sound power level. 1.5.2.1 Determination via sound pressure DIN 45635 Part 1 and Part 23 describe how to determine the sound power levels of a given gear unit /16/. For this purpose, sound pressure levels LpA are measured at fixed points surrounding the gear unit and converted to sound power levels LWA. The measurement surface ratio LS is an auxiliary quantity which is dependent on the sum of the measurement surfaces. When the gear unit is placed on a reverberant base, the bottom is not taken into consideration, see example in figure 27.
Machine enclosing reference box Measurement surface
The results correspond to the sound power levels as determined in accordance with DIN 45635. This procedure requires a larger number of devices to be used, however, it is a very quick one. Above all, foreign influences are eliminated in the simplest way. 1.5.3 Prediction It is not possible to exactly calculate in advance the sound power level of a gear unit to be made. However, one can base the calculations on experience. In the VDI guidelines 2159 /17/, for example, reference values are given. Gear unit manufacturers, too, mostly have own records. The VDI guidelines are based on measurements carried out on a large number of industrial gear units. Main influence parameters for gear unit noises are gear unit type, transmitted power, manufacturing quality and speed. In VDI 2159, a Gear units Cylindrical gear units (rolling bearings) Cylindrical gear units (sliding bearings) Bevel gear and bevel-helical gear units Planetary gear units Worm gear units For restrictions, see VDI 2159.
fo / fu = 2, i.e. fo / fu = 1.26, fo = fm . 1.12 and fu = fm / 1.12;

fm = mean band frequency, fo = upper band frequency, fu = lower band frequency. In case of octaves, the upper frequency is as twice as big as the lower one, or fo = fm . 1.41 and fu = fm / 1.41.
Bandwidth Sound intensity level dB(A)
distinction is made between cylindrical gear units with rolling bearings, see figure 28, cylindrical gear units with sliding bearings (high-speed gear units), bevel gear and bevel-helical gear units, planetary gear units and worm gear units. Furthermore, information on speed variators can be found in the guidelines. Figure 28 exemplary illustrates a characteristic diagram of emissions for cylindrical gear units. Similar characteristic diagrams are also available for the other gear unit types mentioned. Within the characteristic diagrams, 50%- and 80%-lines are drawn. The 80%-line means, for example, that 80% of the recorded industrial gear units radiate lower noises. The lines are determined by mathematical equations. For the 80%-lines, the equations according to VDI 2159 are: Total sound power level LWA 77.1 + 12.3 . log P / kW (dB) 85.6 + 6.4 . log P / kW (dB) 71.7 + 15.9 . log P / kW (dB) 87.7 + 4.4 . log P / kW (dB) 65.0 + 15.9 . log P / kW (dB)
Frequency (HZ)
Figure 25 One-third octave spectrum of a gear unit (sound intensity level, A-weighted)
Bandwidth Sound intensity level dB(A)
In order to really detect the noise radiated by the gear unit alone, corrections for background noise and environmental influences are to be made. It is not easy to find the correct correction values, because in general, other noise radiating machines are in operation in the vicinity. 1.5.2.2 Determination via sound intensity The gear unit surface is scanned manually all around at a distance of, for instance, 10 cm, by means of a special measuring device containing two opposing microphones. The mean of the levels is taken via the specified time, e.g. two minutes. An analyzer computes the intensity or power levels in one-third octave or octave bands. The results can be seen on a display screen. In most cases, they can also be recorded or printed, see figures 25 and 26.
Frequency (HZ)
Figure 26 Octave spectrum of a gear unit (sound intensity level, A-weighted) The total level (resulting from logarithmic addition of individual levels of the recorded frequency
132
Sound power level LWA
Figure 27 Example of arrangement of measuring points according to DIN 45 635 /16/
Type: Cylindrical gear units with external teeth mainly (> 80%) having the following characteristic features: Housing: Cast iron housing Bearing arrangement: Logarithmic regression LWA = 77.1 + 12.3 x log P/kW dB Rolling bearings (80%-line) Lubrication: Certainty rate r2 = 0.83 Dip lubrication Probability 90% Installation: Rigid on steel or concrete Power rating: 0.7 up to 2400 kW Input speed (= max. speed): 1000 up to 5000 min-1 (mostly 1500 min-1) Max. circumferential speed: 1 up to 20 ms-1 Output torque: 100 up to 200000 Nm No. of gear stages: 1 to 3 Mechanical power rating P Information on gear teeth: HS gear stage with helical teeth (b = 10 up to 30), hardened, fine-machined, DIN quality 5 to 8 Figure 28 Characteristic diagram of emissions for cylindrical gear units (industrial gear units) acc. to VDI 2159 /17/
133
The measurement surface sound pressure level LpA at a distance of 1 m is calculated from the total sound power level LpA = LWA Ls (dB) Ls = 10 . log S (dB) (28) (29)
S = Sum of the hypothetical surfaces (m2) enveloping the gear unit at a distance of 1 m (ideal parallelepiped) Example of information for P = 100 kW in a 2-stage cylindrical gear unit of size 200 (centre distance in the 2nd gear stage in mm), with rolling bearings, of standard quality: The sound power level, determined in accordance with DIN 45635 (sound pressure measurement) or according to the sound intensity measurement method, is 102 + 2 dB (A). Room and connection influences have not been taken into consideration. If it is agreed that measurements are to be made they will be carried out on the manufacturers test stand. Note: For this example, a measurement surface sound pressure level of 102 - 13.2 89 db (A), tolerance + 2 dB, is calculated at a distance of 1 m with a measurement surface S = 21 m2 and a measurement surface ratio LS = 13.2 dB. Individual levels in a frequency spectrum cannot safely be predicted for gear units because of the multitude of influence parameters.
1.5.4 Possibilities of influencing With the selection of other than standard geometries and with special tooth modifications (see section 1.2.5), gear unit noises can be positively influenced. In some cases, such a procedure results in a reduction in the performance (e.g. module reduction) for the same size, in any case, however, in special design and manufacturing expenditure. Housing design, distribution of masses, type of rolling bearing, lubrication and cooling are also important. Sometimes, the only way is to enclose the gear units which makes possible that the total level is reduced by 10 to 25 dB, dependent on the conditions. Attention has to be paid to it, that no structureborne noise is radiated via coupled elements (couplings, connections) to other places from where then airborne noise will be emitted. A sound screen does not only hinder the propagation of airborne noise but also the heat dissipation of a gear unit, and it requires more space.
Shaft Couplings General Fundamental Principles Rigid Couplings Torsionally Flexible Couplings Torsionally Rigid Couplings Positive Clutches Friction Clutches Synoptical Table of Torsionally Flexible and Torsionally Rigid Couplings Positive Clutches and Friction Clutches
Page 136 136 136-138 138 138 138 139 140
134
135
Shaft Couplings General Fundamental Principles Rigid and Torsionally Flexible Couplings
2. Shaft couplings 2.1 General fundamental principles In mechanical equipment, drives are consisting of components like prime mover, gear unit, shafts and driven machine. Such components are connected by couplings which have the following tasks: - Transmitting an as slip-free as possible motion of rotation, and torques; - Compensating shaft misalignments (radial, axial, angular); - Reducing the torsional vibration load, influencing and displacing the resonant ranges; Damping torque and speed impulses; Interrupting the motion of rotation (clutches); Limiting the torque; Sound isolation; Electrical insulation.
Shaft Couplings Torsionally Flexible Couplings
The diversity of possible coupling variants is shown in the overview in figure 29. A distinction is made between the two main groups couplings and clutches, and the subgroups rigid/flexible couplings and positive/friction clutches.
The flexible properties of the couplings are generated by means of metal springs (coil springs, leaf springs) or by means of elastomers (rubber, plastics). For couplings incorporating flexible metal elements, the torsional flexibility is between 2 and 25 degree, depending on the type. The stiffness characteristics, as a rule, show a linear behaviour, unless a progressive characteristic has intentionally been aimed for by design measures. Damping is achieved by means of friction and viscous damping means. In case of couplings incorporating elastomer elements, a distinction is made between couplings of average flexibility with torsion angles of 2 up to 5 degree and couplings of high flexibility with torsion angles of 5 up to 30 degree. Depending on the type, the flexible elements of the coupling are subjected to compression (tension), bending and shearing, or to a combined form of stressing. In some couplings (e.g. tyre couplings), the flexible elements are reinforced by fabric or thread inserts. Such inserts absorb the coupling forces and prevent the elastic-viscous flow of the elastomer. Couplings with elastomer elements primarily subjected to compression and bending have non-linear progressive stiffness characteristics, while flexible elements (without fabric insert) merely subjected to shearing generate linear stiffness characteristics. The quasi-statical torsional stiffness of an elastomer coupling increases at dynamic load (up to approximately 30 Hz, test frequency 10 Hz) by approximately 30 to 50%. The dynamic stiffness of a coupling is influenced [(+) increased; () reduced] by the average load (+), the oscillation amplitude (), temperature (), oscillation frequency (+), and period of use (). For rubber-flexible couplings, the achievable damping values are around = 0.8 up to 2 (damping coefficient ; DIN 740 /18/). Damping leads to heating of the coupling, and the heat loss has to be dissipated via the surface. The dynamic loading capacity of a coupling is determined by the damping power and the restricted operating temperature of elastomers of 80C up to max. 100C. When designing drives with torsionally flexible couplings according to DIN 740 /18/, torsional vibrations are taken into account by reducing the drive to a two-mass vibration generating system, or by using torsional vibration simulation programs which can compute detailed vibration systems for both steady and unsteady conditions. Examples of couplings incorporating elastomer elements of average flexibility are claw-, pin-, and pin and bush couplings.
The N-EUPEX coupling is a wear-resistant pin coupling for universal use (figure 30) absorbing large misalignments. The coupling is available as fail-safe coupling and as coupling without failsafe device. In its three-part design it is suitable for simple assembly and simple replacement of flexible elements. The coupling is made in different types and sizes for torques up to 62,000 Nm. The BIPEX coupling is a flexible fail-safe claw coupling in compact design for high power capacity and is offered in different sizes for maximum torques up to 3,700 Nm. The coupling is especially suitable for plug-in assembly and fitting into bell housings. The RUPEX coupling is a flexible fail-safe pin and bush coupling which as a universal coupling is made in different sizes for low up to very high torques (106 Nm) (figure 31). The coupling is suitable for plug-in assembly and capable of absorbing large misalignments. The optimized shape of the barrelled buffers and the conical seat of the buffer bolts facilitate assembly and guarantee maintenance-free operation. Because of their capability to transmit high torques, large RUPEX couplings are often used on the output side between gear unit and driven machine. Since the coupling hubs are not only offered in grey cast iron but also in steel, the couplings are also suitable for high speeds. Examples of highly flexible couplings incorporating elastomer elements are tyre couplings, flange couplings, ring couplings, and large-volume claw couplings with cellular elastic materials. Examples of flexible couplings incorporating metal elements are coil spring and leaf spring couplings. The ELPEX coupling (figure 32) is a highly flexible ring coupling without torsional backlash which is suitable for high dynamic loads and has good damping properties. Rings of different elasticity are suitable for optimum dynamic tuning of drives. Torque transmitting thread inserts have been vulcanized into the rings out of high-quality natural rubber. Due to the symmetrical design the coupling is free from axial and radial forces and allows large shaft misalignments even under torque loads. Typical applications for ELPEX couplings which are available for torques up to 90,000 Nm are drives with periodically exciting aggregates (internal combustion engines, reciprocating engines) or extremely shockloaded drives with large shaft misalignments. Another highly flexible tyre coupling with a simple closed tyre as flexible element mounted between two flanges is the ELPEX-B coupling. It is available in different sizes for torques up to 20,000 Nm.
Shaft couplings
Couplings
Clutches
Rigid
Flexible
Positive
Friction
Torsionally flexible
Clamp, Flange, Radial tooth Pin and bush, Claw, Tyre, Flange, Coil spring, Leaf spring, Air bag spring, Cardan
Rigid, universal joint

Gear, Steel plate, Membrane, Universal joint, Rolling contact joint, Oldham coupling Claw, Pin and bush, Gear
Friction
Hydrodyn.
Electrodyn.
(*)
Cone, Foettinger Plate, Multiple disk, Centrifugal force, Overrunning, Automatic disengaging, Friction
Eddy current
(*) In case of additional gearing, all clutches are disengageable when stationary.
Figure 29 Overview of possible shaft coupling designs 2.2 Rigid couplings Rigid couplings connect two shaft ends and do practically not allow any shaft misalignment. They are designed as clamp, flange and radial tooth couplings and allow the transmission of high torques requiring only small space. The coupling halves are connected by means of bolts (close fitting bolts). In case of clamp and flange couplings (with split spacer ring), radial disassembly is possible. Radial tooth couplings are self-centering and transmit both high and alternating torques. 2.3 Torsionally flexible couplings Torsionally flexible couplings are offered in many designs. Main functions are the reduction of torque impulses by elastic reaction, damping of torsional vibrations by internal damping in case of couplings with flexible rubber elements, and frictional damping in case of couplings with flexible metal elements, transfer of resonance frequencies by variation of the torsional stiffness, and compensation of shaft misalignments with low restoring forces.
136
137
Shaft Couplings Torsionally Flexible Couplings Torsionally Rigid Couplings Positive and Friction Clutches
This coupling features high flexibility without torsional backlash, absorbs large shaft misalignments, and permits easy assembly and disassembly (radial). The ELPEX-S coupling (figure 33) is a highly flexible, fail-safe claw coupling absorbing large shaft misalignments. The large-volume cellular flexible elements show very good damping properties with low heating and thus allow high dynamic loads. The couplings have linear stiffness characteristics, and with the use of different flexible elements they are suitable for optimum dynamic tuning of drives. The couplings are of compact design and are suitable for torques up to 80,000 Nm. Plug-in assembly is possible. This universal coupling can be used in drives with high dynamic loads which require low frequency with good damping. 2.4 Torsionally rigid couplings Torsionally rigid couplings are used where the torsional vibration behaviour should not be changed and exact angular rotation is required, but shaft misalignment has to be absorbed at the same time. With the use of long floating shafts large radial misalignments can be allowed. Torsionally rigid couplings are very compact, however, they have to be greased with oil or grease (exception: steel plate and membrane couplings). Typical torsionally rigid couplings are universal joint, gear, membrane and steel plate couplings, which always have to be designed as double-jointed couplings with floating shafts (spacers) of different lengths. Universal joints allow large angular misalignments (up to 40 degree), the dynamic load increasing with the diffraction angle. In order to avoid pulsating angular rotation (2 times the torsional frequency), universal joints must always be arranged in pairs (same diffraction angle, forks on the intermediate shaft in one plane, input and output shaft in one plane). Constant velocity joints, however, always transmit uniformly and are very short. Gear couplings of the ZAPEX type (figure 34) are double-jointed steel couplings with crowned gears which are capable of absorbing shaft misalignments (axial, radial and angular up to 1 degree) without generating large restoring forces. The ZAPEX coupling is of compact design, suitable for high speeds, and transmits very high torques (depending on the size up to > 106 Nm), and in addition offers large safety reserves for the absorption of shock loads. It is lubricated with oil or grease. Fields of application are, among others, rolling mills, cement mills, conveyor drives, turbines. The ARPEX coupling (figure 35) is a doublejointed, torsionally rigid plate coupling for the absorption of shaft misalignments (angular up to 1 degree). The coupling is maintenance-free (no lubrication) and wear-resistant and owing to its closed plate packs allows easy assembly. A wide range of ARPEX couplings is available - from the miniature coupling up to large-size couplings for torques up to > 106 Nm. The coupling transmits torques very uniformly, and owing to its all-steel design is suitable for high ambient temperatures (up to 280C) and high speeds. Fields of application are, among others, paper machines, ventilators, pumps, drives for materials-handling equipment as well as for control systems. 2.5 Positive clutches This type includes all clutches which can be actuated when stationary or during synchronous operation in order to engage or disengage a machine to or from a drive. Many claw, pin and bush, or gear couplings can be used as clutches by axially moving the driving member. With the additional design element of interlocking teeth, all flexible couplings can be used as clutches. 2.6 Friction clutches In friction clutches, torques are generated by friction, hydrodynamic or electrodynamic effect. The clutch is actuated externally, even with the shaft rotating (mechanically, hydraulically, pneumatically, magnetical), speed-dependent (centrifugal force, hydrodynamic), torquedependent (slip clutches, safety clutches), and dependent on the direction of rotation (overrunning clutches). Of the different clutch types, friction clutches are most commonly used which may contain either dry- or wet- (oil-lubricated) friction elements. Dependent on the friction element and the number of friction surface areas, a distinction is made between cylindrical, cone, flange and disk clutches. The larger the number of friction surface areas, the smaller the size of the clutch. Further criteria are wear, service life, idle torque, cooling, cycle rate, and uniform friction effect (non-chattering). The PLANOX clutch is a dry-friction multiple disk clutch with one up to three disks, which has been designed with overload protection for application in general mechanical engineering. It is actuated externally by mechanical, electrical, pneumatic or hydraulic force. Uniform transmission of torque is guaranteed by spring pressure even after high cylce rates. The clutch is made in different types and sizes for torques up to 3 S 105 Nm.
Shaft Couplings Synoptical Table of Torsionally Flexible and Torsionally Rigid Couplings
Figure 30 Flexible pin coupling, N-EUPEX, in three parts
Figure 33 Highly flexible claw coupling with cellular flexible elements, ELPEX-S
Figure 31 Flexible pin and bush coupling, RUPEX
Figure 34 Gear coupling, ZAPEX
Figure 32 Highly flexible ring coupling, ELPEX
Figure 35 All-steel coupling, with plate packs, ARPEX
138
139
Shaft Couplings Friction Clutches Fluid Couplings

The AUTOGARD torque limiter is an automatically actuating safety clutch which disconnects driving and driven side by means of a high-accuracy ball-operated mechanism and interrupts the transmission of torque as soon as the set disengagement torque is exceeded. The torque limiter is ready for operation again when the mechanism has been re-engaged during standstill. The clutch is made in different sizes for disengagement torques up to 56,500 Nm. Speed-controlled clutches allow soft starting of heavy-duty driven machines, the motor accelerating itself at first and then driving the machine. This permits the use of smaller dimensioned motors for high mass moments of inertia and a high number of starts. Speed-controlled clutches are designed as centrifugal clutches with segments, e.g. retaining springs which transmit torques only from a specified operating speed on, or with pellets (powder, balls, rollers). The torque which is generated by friction on the lateral area of the output part increases as the square of the input speed. After running up, the clutch operates without slip. The FLUDEX coupling (figure 36) is a hydrodynamic fluid coupling operating according to the Fttinger principle without mechanical friction. The coupling parts on the input (pump) and output (turbine) side are not mechanically connected and thus wear-resistant. Torque is transmitted by the rotating oil fluid in the coupling accelerated by the radial blades (pulse exchange). Fluid couplings have the same characteristics as turbines; torque increases with the second power, and power capacity is proportional to the third power of the input speed. During steady torque transmission little operating slip occurs which heats up the coupling. As safety elements for limiting the temperature, fusible safety plugs and electronically or mechanically controlled temperature monitors are used. Fluid couplings are mainly used for starting great masses, for separating torsional vibrations, and for limiting overloads during starting and in case of blockages.
Vibrations Symbols and Units General Fundamental Principles Solution Proposal for Simple Torsional Vibrators Solution of the Differential Equation of Motion Formulae for the Calculation of Vibrations Mass Mass Moment of Inertia Symbols and Units of Translational and Torsional Vibrations Determination of Stiffness Overlaying of Different Stiffnesses Conversions Natural Frequencies Evaluation of Vibrations
Page 142 143-145 145/146 146/147 147 147 147 148 149 150 150 150/151 151/152
Outer wheel drive 1 Blade wheel housing (outer wheel) 2 Cover 3 Fusible safety plug 4 Filler plug 5 Impeller (inner wheel) 6 Hollow shaft 7 Delay chamber 8 Working chamber 9 Flexible coupling (N-EUPEX D) 10 Damming chamber
Figure 36 Basic design of a fluid coupling with and without delay chamber, FLUDEX type
140
141
Vibrations Symbols and Units
Vibrations General Fundamental Principles
a A A AD; Ae c c d di da D Dm e= E f, fe f F F (t) G i iF la lp J, Ji J* k k l m, mi M (t) Mo Mo* ne n1; n2 q
m m2 m, rad
Length of overhanging end Cross-sectional area Amplitude of oscillation Damping energy; elastic energy
t T T V V x
^ x
s s Nm m3 m m rad rad 1/s rad 3.142 kg/m3 rad rad rad/s rad/s2 rad rad rad rad rad/s rad/s rad/s
Time Period of a vibration Torque Volume Magnification factor; Dynamic/ static load ratio Displacement co-ordinate (translational, bending) Displacement amplitude Phase angle Phase angle with free vibration Damping constant Phase displacement angle with forced vibration Excitation frequency/natural frequency ratio Inherent value factor for i-th natural frequency Logarithmic decrement Peripheral/diameter ratio Specific density Angle of rotation Angular amplitude of a vibration Angular velocity (first time derivation of ) Angular acceleration (second time derivation of ) Vibratory angle of the free vibration (homogeneous solution) Vibratory angle of the forced vibration (particular solution) Angular amplitude of the forced vibration Angular amplitude of the forced vibration under load ( = 0) Damping coefficient acc. to DIN 740 /18/
3.
Vibrations
Nm/ rad N/m m m m m 2.718 N/m2 Hz m N N N/m2 m4 m4 kgm2 kgm2 Nms/ rad Ns/m m kg Nm Nm Nm 1/min 1/min
Torsional stiffness Translational stiffness; bending stiffnes Diameter Inside diameter Outside diameter Attenuation ratio (Lehrs damping) Mean coil diameter (coil spring) Natural number Modulus of elasticity Frequency; natural frequency Deformation Force Time-variable force Shear modulus Transmission ratio Number of windings (coil spring) Axial moment of area Polar moment of area Mass moment of inertia Reduced mass moment of inertia of a two-mass vibration generating system Viscous damping in case of torsional vibrations Viscous damping in case of translational and bending vibrations Length; distance between bearings Mass Time-variable excitation moment Amplitude of moment Reduced amplitude of moment of a two-mass vibration generating system Natural frequency (vibrations per minute) Input speed; output speed Influence factor for taking into account the mass of the shaft when calculating the natural bending frequency
i = r , i
^ .
3.1 General fundamental principles Vibrations are more or less regularly occurring temporary variations of state variables. The state of a vibrating system can be described by suitable variables, such as displacement, angle, velocity, pressure, temperature, electric voltage/ current, and the like. The simplest form of a mechanical vibrating system consists of a mass and a spring with fixed ends, the mass acting as kinetic energy store
and the spring as potential energy store, see figure 37. During vibration, a periodic conversion of potential energy to kinetic energy takes place, and vice versa, i.e. the kinetic energy of the mass and the energy stored in the spring are converted at certain intervals of time. Dependent on the mode of motion of the mass, a distinction is made between translational (bending) and torsional vibrating systems as well as coupled vibrating systems in which translational and torsional vibrations occur at the same time, influencing each other.
Translational vibration generatig system
Bending vibration generating system
Torsional vibration generating system
Figure 37 Different vibrating systems with one degree of freedom Further, a distinction is made between free vibrations and externally forced vibrations, and whether the vibration takes place without energy losses (undamped) or with energy losses (damped). A vibration is free and undamped if energy is neither supplied nor removed by internal friction so that the existing energy content of the vibration is maintained. In this case the system carries out steady-state natural vibrations the frequency of which is determined only by the characteristics of the spring/mass system (natural frequency), figure 39a. The vibration variation with time x can be described by the constant amplitude of oscillation A and a harmonic function (sine, cosine) the arguments of which contain natural radian frequency = 2 . f (f = natural frequency in Hertz) and time, see figure 38.
..
h p
^
p
^
stat
Amplitude Vibration
Amplitude
Angular velocity, natural radian frequency of the damped vibration Natural radian frequency of the undamped vibration Radian frequency of the excitating vibration
Period x A t = = = = A . sin . t Amplitude Radian frequency Time
Note: The unit rad may be replaced by 1.
x = A . sin ( . t + ) = Phase angle
Figure 38 Mathematical description of an undamped vibration with and without phase angle
142
143
Vibrations General Fundamental Principles
Vibrations General Fundamental Principles Solution Proposal for Simple Torsional Vibrators
lead to high loads in the components and therefore are to be avoided or to be quickly traversed. (Example: natural bending frequency in highspeed gear units). The range of the occurring amplitudes of oscillation is divided by the resonance point (natural frequency = excitation frequency, critical vibrations) into the subcritical and supercritical oscillation range. As a rule, for technical vibrating systems (e.g. drives), a minimum frequency distance of 15% or larger from a resonance point is required. Technical vibrating systems often consist of several masses which are connected with each other by spring or damping elements. Such systems have as many natural frequencies with the corresponding natural vibration modes as degrees of freedom of motion. A free, i.e. unfixed torsional vibration system with n masses, for instance, has n-1 natural frequencies. All these natural frequencies can be excited to vibrate by periodic external or internal forces, where mostly only the lower natural frequencies and especially the basic frequency (first harmonic) are of importance. In technical drive systems, vibrations are excited by the following mechanisms: a) From the input side: Starting processes of electric motors, system short circuits, Diesel Otto engines, turbines, unsteady processes, starting shock impulses, control actions. b) From transmitting elements: Meshing, unbalance, universal-joint shaft, alignment error, influences from bearings. c) From the output side: Principle of the driven machine, uniform, nonuniform, e.g. piston compressor, propeller. As a rule, periodic excitation functions can be described by means of sine or cosine functions and the superpositions thereof. When analysing vibration processes, a Fourier analysis may often be helpful where periodic excitation processes are resolved into fundamental and harmonic oscillations and thus in comparison with the natural frequencies of a system show possible resonance points. In case of simple vibrating systems with one or few (maximum 4) masses, analytic solutions for the natural frequencies and the vibration variation with time can be given for steady excitation. For unsteady loaded vibrating systems with one or more masses, however, solutions can be calculated only with the aid of numerical simulation programmes. This applies even more to vibrating systems with non-linear or periodic variable parameters (non-linear torsional stiffness of couplings; periodic meshing stiffnesses). With EDP programmes, loads with steady as well as unsteady excitation can be simulated for complex vibrating systems (linear, non-linear, parameter-excited) and the results be represented in the form of frequency analyses, load as a function of time, and overvoltages of resonance. Drive systems with torsionally flexible couplings can be designed dynamically in accordance with DIN 740 /18/. In this standard, simplified solution proposals for shock-loaded Fixed one-mass vibration generating system and periodically loaded drives are made, the drive train having been reduced to a two-mass vibration generating system. 3.2 Solution proposal for simple torsional vibrators Analytic solution for a periodically excited one(fixed) or two-mass vibration generating system, figure 40.
A damped vibration exists, if during each period of oscillation a certain amount of vibrational energy is removed from the vibration generating system by internal or external friction. If a constant viscous damping (Newtons friction) exists, the amplitudes of oscillation decrease in accordance with a geometric progression, figure 39b. All technical vibration generating systems are subject to more or less strong damping effects. Displacement x
Free two-mass vibration generating system
a) Undamped vibration ( = 0)
Figure 40 Torsional vibrators J, J1, J2 c k M (t) = mass moment of inertia [kgm2] = torsional stiffness [Nm/rad] = viscous damping [Nms/rad] = external excitation moment [Nm] , time-variable = angle of rotation [rad] , ( = 1 2 for 2-mass vibration generating systems as relative angle) = angular velocity [rad/s] (first time derivation of ) = angular acceleration [rad/s2] (second time derivation of ) J1 ) J2 J1 J2
b) Damped vibration ( > 0)
..
c) Stimulated vibration ( < 0) Time t Figure 39 Vibration variations with time (A = initial amplitude at time t = 0; = damping constant) If the vibrating system is excited by a periodic external force F(t) or moment M(t), this is a forced or stimulated vibration, figure 39c. With the periodic external excitation force, energy can be supplied to or removed from the vibrating system. After a building-up period, a damped vibrating system does no longer vibrate with its natural frequency but with the frequency of the external excitation force. Resonance exists, when the applied frequency is at the natural frequency of the system. Then, in undamped systems the amplitudes of oscillation grow at an unlimited degree. In damped systems, the amplitude of oscillation grows until the energy supplied by the excitation force and the energy converted into heat by the damping energy are in equilibrium. Resonance points may
Differential equation of motion: One-mass vibration generating system:

..
rad s
(35)
)k J 2
)c J (
2 o
M (t) J
(30)
Natural frequency: fe
o
Two-mass vibration generating system with relative coordinate:

..
2
o
[Hz] 30
(36)
) k J* (
2
) c J* + (
2 o 2
M(t) J1
ne (31) k J
[1/min] [1/s]
(37) (38)
damping constant
with J* J1
(32) (33)
J2
J1 ) J2
o = natural radian frequency of the undamped vibration in rad/s fe = natural frequency in Hertz ne = natural frequency in 1/min Damped natural radian frequency:
Natural radian frequency (undamped):

o
c J
[ rad/s]
(34)
2 o
1 + D2
(39)
144
145
Vibrations Solution Proposal for Simple Torsional Vibrators Solution of the Differential Equation of Motion
Attenuation ratio (Lehrs damping): D D k 2
o
Vibrations Solution of the Differential Equation of Motion Formulae for the Calculation of Vibrations
a) Free vibration (homogeneous solution h) (40)

h
e {+
t}
cos (
t+
(43) Magnification factor V
= damping coefficient on torsionally flexible coupling, determined by a damping hysteresis of a period of oscillation acc. to DIN 740 /18/ and/or acc. to Flender brochure damping energy elastic deformation energy AD Ae
b) Forced vibration (particular solution p)

p
Reference values for some components: D = 0.001...0.01 shafts (material damping of steel) D = 0.04...0.08 gear teeth in gear units D = 0.04...0.15 (0.2) torsionally flexible couplings D = 0.01...0.04 gear couplings, all-steel couplings, universal joint shafts Static spring characteristic for one load cycle
M* o c
(1 + t+ )
2) 2
1 ) 4D 2
cos(m
(44) 2 D
2
Frequency ratio
m
o
Phase angle:
tan
1+ m
o
(45)
Figure 42 Magnification factors for forced, damped and undamped vibrations at periodic moment excitation (power excitation). Magnification factors V and phase displacement angle .
Frequency ratio:
(46) 3.4 Formulae for the calculation of vibrations For the calculation of natural frequencies and vibrational loads, a general vibration generating system has to be converted to a calculable substitute system with point masses, spring and damping elements without mass. 3.4.1 Mass m = r.V [kg] [kg/m3]
One-mass vibration generating system: Mo * Mo Two-mass vibration generating system: J2 Mo * Mo J1 ) J2
(47)
(48)
c) Magnification factor Mo * c V cos (m t+ )

^
V = volume [m3] r = specific density (49)
Figure 41 Damping hysteresis of a torsionally flexible component V 3.3 Solution of the differential equation of motion
^
3.4.2 Mass moment of inertia

p
1 (1 + 2) 2 ) 4D 2
stat
M (50) M* o
J =
r 2 dm:
general integral formula
Periodic excitation moment M(t) Mo cos m t (41)

^
= vibration amplitude of forced vibration = vibration amplitude of forced vibration at a frequency ratio = 0.
stat
Circular cylinder: 1 r J d4 l p (kgm2r 32 d = diameter [m] l = length of cylinder p mr
Mo = amplitude of moment [Nm] = exciting circuit frequency [rad/s] Total solution:

h
The magnification factor shows the ratio of the dynamic and static load and is a measure for the additional load caused by vibrations (figure 42). (42)
146
147
Phase displacement angle
Constants A and are determined by the starting . conditions, e.g. by h = 0 and h= 0 (initial-value problem). In damped vibrating systems ( > 0) the free component of vibration disappears after a transient period.
Vibrations Terms, Symbols and Units
Vibrations Formulae for the Calculation of Vibrations
Table 8 Symbols and units of translational and torsional vibrations Term Mass, Mass moment of inertia Instantaneous value of vibration (displacement, angle) Amplitude Oscillating velocity Inertia force, Moment of inertia forces Spring rate, Torsional spring rate Spring force, Spring moment Attenuation constant (Damping coefficient), Attenuation constant for rotary motion Damping factor (Decay coefficient) Attenuation ratio (Lehrs damping) Damping ratio Logarithmic damping decrement Time Phase angle Phase displacement angle Period of a vibration Frequency of natural vibration Radian frequency of natural vibration Natural radian frequency (Natural frequency) Natural radian frequency when damped Excitation frequency Radian frequency ratio
d
3.4.3 Determination of stiffness Explanation Table 9 Calculation of stiffness (examples) Example Coil spring G 8 d4 if N m iF = G = d = Dm = number of windings shear modulus 1) diameter of wire mean coil diameter Stiffness Symbol
Quantity m J x
^ x max, x , A ^ max, , A
Unit kg kg . m2 m rad*) m rad m/s rad/s
Translatory vibrating mass m; Torsionally vibrating mass with mass moment of inertia J Instantaneous, time-dependent value of vibration amplitude Amplitude is the maximum instantaneous value (peak value) of a vibration. Oscillating velocity; Velocity is the instantaneous value of the velocity of change in the direction of vibration. The dAlemberts inertia force or the moment of inertia force acts in the opposite direction of the positive acceleration.
D3 m
x x ..
..
Torsion bar c
G I
Ip
m J c c c . x c. k k
N NSm
Nm rad d4 32 32
4 (d 4 a + di )
Nm Linear springs N S m/rad N In case of linear springs, the spring recoil N S m is proportional to deflection. In case of Newtons friction, the damping N S s/m force is proportional to velocity and Nms/rad attenuation constant (linear damping). 1/s 1/s s rad rad s Hz rad/s rad/s rad/s The damping factor is the damping coefficient referred to twice the mass. For D < 1, a damped vibration exists; for D 1, an aperiodic case exists. The damping ratio is the relation between two amplitudes, one cycle apart. p p In (x n x n)1) In ( ^ n ^ n)1)
^ ^
Shaft : I p Hollow shaft : I p Tension bar E I A
Ip = polar moment of inertia l = length d, di, da = diameters of shafts
= k/(2 . m) = k/(2 . J) D = / xn
^ ^
N m
E = modulus of elasticity 1) A = cross-sectional area
x n) 1
^
n) 1
Cantilever beam
D 1 + D2 t
F f Shaft :
E Ia l3 Ia 64
N m d4 64
4 (d 4 a + di )
F f
= 1 2 T = 2 . / f = 1/T = /(2 . ) = 2 . . f
o o
Coordinate of running time In case of a positive value, it is a lead angle. Difference between phase angles of two vibration processes with same radian frequency. Time during which a single vibration occurs. Frequency is the reciprocal value to a period of vibrations; vibrations per sec. Radian frequency is the number of vibrations in 2 . seconds. Vibration frequency of the natural vibration (undamped) of the system For a very small attenuation ratio D < 1 becomes d o. Radian frequency of excitation Resonance exists at = 1.
= force = deformation at centre of mass under force F Ia = axial moment of area
Hollow shaft : I a Transverse beam (single load in middle) c F f 48 E l3
Ia
N m
c m c J
2 o
Transverse beam with overhanging end c F f
l 3 a2 E Ia (l ) a) N m a
+ r2 rad/s
= distance between bearings = length of overhanging end
= /
*) The unit rad may be replaced by 1.
1) For steel: E = 21 S 1010 N/m2; G = 8.1 S 1010 N/m2
148
149
Vibrations Formulae for the Calculation of Vibrations Evaluation of Vibrations

3.4.4 Overlaying of different stiffnesses To determine resulting stiffnesses, single stiffnesses are to be added where arrangements in series connection or parallel connection are possible. Series connection: Rule: The individual springs in a series connection carry the same load, however, they are subjected to different deformations. 1 c ges 1 1 1 1 c1 ) c2 ) c3 ) ) cn (53) 3.4.6 Natural frequencies a) Formulae for the calculation of the natural frequencies of a fixed one-mass vibration generating system and a free two-mass vibration generating system. Natural frequency f in Hertz (1/s): One-mass vibration generating system: Torsion : f e + 1 2p c J (58) Two-mass vibration generating system:
fe + 1 2p J1 ) J2 J1 J2
Measuring the stiffness: In a test, stiffness can be determined by measuring the deformation. This is particularly helpful if the geometric structure is very complex and very difficult to acquire. Translation: F N m c f F = applied force [N] f = measured deformation [m] Torsion: T Nm rad c T = applied torsion torque [Nm] = measured torsion angle [rad] Measurements of stiffness are furthermore required if the material properties of the spring material are very complex and it is difficult to rate them exactly. This applies, for instance, to rubber materials of which the resilient properties are dependent on temperature, load frequency, load, and mode of stress (tension, compression, shearing). Examples of application are torsionally flexible couplings and resilient buffers for vibration isolation of machines and internal combustion engines. These components often have non-linear progressive stiffness characteristics, dependent on the direction of load of the rubber material. For couplings the dynamic stiffness is given, as a rule, which is measured at a vibrational frequency of 10 Hz (vibrational amplitude = 25% of the nominal coupling torque). The dynamic torsional stiffness is greater than the static torsional stiffness, see figure 43. (51)
(59)
(52)
Parallel connection: Rule: The individual springs in a parallel connection are always subject to the same deformation. c ges c1 ) c2 ) c3 ) ) cn (54)
c = torsional stiffness in [Nm/rad] J, Ji = mass moments of inertia in [kgm2]

Translation, Bending : f e + 1 2p c m
(60)
fe + 1 2p
m1 ) m2 m1 m2
(61)
3.4.5 Conversions If drives with different speeds or shafts are combined in one vibration generating system, the stiffnesses and masses are to be converted to a reference speed (input or output). Conversion is carried out as a square of the transmission ratio: Transmission ratio: i n1 n2 reference speed speed (55)
c = translational stiffness (bending stiffness) in [N/m] m, mi = masses in [kg] b) Natural bending frequencies of shafts supported at both ends with applied masses with known deformation f due to the dead weight
fe + q 2p g f [Hz
Table 10 -values for the first three natural frequencies, dependent on mode of fixing Bearing application 1 1.875 4.730 3.927 2 4.694 7.853 2 7.069 3 7.855 10.966 3 10.210
(62)
Conversion of stiffnesses cn2 and masses Jn2 with speed n2 to the respective values cn1 and Jn1 with reference speed n1: C n1 J n1 c n2 i 2 J n2 i 2 (56) (57)
Before combining stiffnesses and masses with different inherent speeds, conversion to the common reference speed has to be carried out first. Slope = static stiffness
g = 9.81 gravity f = deformation due to dead weight [m] q = factor reflecting the effect of the shaft masses on the applied mass q = 1 shaft mass is neglected compared with the applied mass q = 1.03 ... 1.09 common values when considering the shaft masses q = 1.13 solid shaft without pulley c) Natural bending frequencies for shafts, taking into account dead weights (continuum); general formula for the natural frequency in the order fe, i.
f e,i + 1 2p mi l
2
m/s2
For the solid shaft with free bearing support on both sides, equation (63) is simplified to:
f e,i + p d 8 i l
2
E r
Hz
(64)
i = 1st, 2nd, 3rd ... order of natural bending frequencies. 3.5 Evaluation of vibrations The dynamic load of machines can be determined by means of different measurement methods. Torsional vibration loads in drives, for example, can be measured directly on the shafts by means of wire strain gauges. This requires, however, much time for fixing the strain gauges, for calibration, signal transmission and evaluation. Since torques in shafts are generated via bearing pressure in gear units, belt drives, etc., in case of dynamic loads, structure-borne noise is generated which can be acquired by sensing elements at the bearing points in different directions (axial, horizontal, vertical).
E Hz r A
(63)
Slope = dynamic stiffness
Figure 43 Static and dynamic torsional stiffness
i = inherent value factor for the i-th natural frequency l = length of shaft [m] E = modulus of elasticity [N/m2] I = moment of area [m4] r = density [kg/m3] A = cross-sectional area [m2] d = diameter of solid shaft [m]
150
151
Dependent on the requirements, the amplitudes of vibration displacement, velocity and acceleration can be recorded and evaluated in a sum (effective vibration velocity) or frequencyselective. The structure-borne noise signal reflects besides the torque load in the shafts also unbalances, alignment errors, meshing impulses, bearing noises, and possibly developing machine damages. To evaluate the actual state of a machine, VDI guideline 2056 1) or DIN ISO 10816-1 /19, 20/ is consulted for the effective vibration velocity, as a rule, taking into account structure-borne noise in the frequency range between 10 and 1,000 Hertz. Dependent on the machine support structure (resilient or rigid foundation) and power transmitted, a distinction is made between four machine groups (table 11). Dependent on the vibration velocity, the vibrational state of a
machine is judged to be good, acceptable, still permissible, and non-permissible. If vibration velocities are in the non-permissible range, measures to improve the vibrational state of the machine (balancing, improving the alignment, replacing defective machine parts, displacing the resonance) are required, as a rule, or it has to be verified in detail that the vibrational state does not impair the service life of the machine (experience, verification by calculation). Structure-borne noise is emitted from the machine surface in the form of airborne noise and has an impact on the environment by the generated noises. For the evaluation of noise, sound pressure level and sound intensity are measured. Gear unit noises are evaluated according to VDI guideline 2159 or DIN 45635 /17, 16/, see subsection 1.5.
Page Bibliography of Sections 10, 11, and 12 154/155
Table 11 Boundary limits acc. to VDI guideline 2056 1) for four machine groups Including gear units and machines with input power ratings of ... ... up to approx. 15 kW without special foundation. ... from approx. 15 up to 75 kW without special foundation. M ... from approx. 75 up to 300 kW and installation on highly tuned, rigid or heavy foundations. ... over 300 kW and installation on highly tuned, rigid or heavy foundations. ... over 75 kW and installation on broadly tuned resilient foundations (especially also steel foundations designed according to lightconstruction guidelines). up to 1.1 1.1 ... 2.8 2.8 ... 7.1 from 7.1 up Range classification acc. to VDI 2056 (Effective value of the vibration velocity in mm/s) Good up to 0.7 Acceptable 0.7 ... 1.8 Still permissible 1.8 ... 4.5 Non-permissible from 4.5 up
Machine groups
up to 1.8
1.8 ... 4.5
4.5 ... 11
from 11 up
up to 2.8
2.8 ... 7
7 ... 18
from 18 up
1) 08/97 withdrawn without replacement; see /20/
152
153
Bibliography
Bibliography
/1/
DIN 3960: Definitions, parameters and equations for involute cylindrical gears and gear pairs. March 1987 edition. Beuth Verlag GmbH, Berlin DIN 3992: Addendum modification of external spur and helical gears. March 1964 edition. Beuth Verlag GmbH, Berlin
/13/
/2/
FVA-Ritzelkorrekturprogramm: EDV-Programm zur Ermittlung der Zahnflankenkorrekturen zum Ausgleich der lastbedingten Zahnverformungen (jeweils neuester Programmstand). FVAForschungsvorhaben Nr. 30. Forschungsvereinigung Antriebstechnik, Frankfurt am Main Niemann, G.: Maschinenelemente 2. Bd., Springer Verlag Berlin, Heidelberg, New York (1965) Theissen, J.: Vergleichskriterien fr Grossgetriebe mit Leistungsverzweigung. VDI-Bericht 488 Zahnradgetriebe 1983 - mehr Know how fr morgen, VDI-Verlag, 1983 DIN 45635: Measurement of noise emitted by machines. Part 1: Airborne noise emission; Enveloping surface method; Basic method, divided into 3 grades of accuracy; April 1984 edition Part 23: Measurement of airborne noise; Enveloping surface method; Gear transmission; July 1978 edition Beuth Verlag GmbH, Berlin VDI-Richtlinien 2159: Emissionskennwerte technischer Schallquellen; Getriebegerusche; Verein Deutscher Ingenieure, July 1985 DIN 740: Flexible shaft couplings. Part 2. Parameters and design principles. August 1986 edition; Beuth Verlag GmbH, Berlin VDI-Richtlinien 2056: Beurteilungsmasstbe fr mechanische Schwingungen von Maschinen. VDI-Handbuch Schwingungstechnik; Verein Deutscher Ingenieure; October 1964; (08/97 withdrawn without replacement) DIN ISO 10816-1: Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts. August 1997 edition; Beuth Verlag GmbH, 10772 Berlin
/14/ /3/ DIN 3993: Geometrical design of cylindrical internal involute gear pairs; Part 3. August 1981 edition. Beuth Verlag GmbH, Berlin DIN 3994: Addendum modification of spur gears in the 05-system. August 1963 edition. Beuth Verlag GmbH, Berlin Niemann, G. und Winter, H.: Maschinenelemente, Band II, Getriebe allgemein, Zahnradgetriebe-Grundlagen, Stirnradgetriebe. 3rd edition. Springer Verlag, Heidelberg, New York, Tokyo (1985) Sigg, H.: Profile and longitudinal corrections on involute gears. Semi-Annual Meeting of the AGMA 1965, Paper 109.16 Hsel, Th.: Ermittlung von Tragbild und Flankenrichtungskorrekturen fr Evolventen-Stirnrder. Berechnungen mit dem FVA-Programm Ritzelkorrektur. Zeitschrift Antriebstechnik 22 (1983) Nr. 12 DIN 3990: Calculation of load capacity of cylindrical gears. Part 1: Introduction and general influence factors Part 2: Calculation of pitting resistance Part 3: Calculation of tooth strength Part 4: Calculation of scuffing load capacity Beuth Verlag GmbH, Berlin, December 1987 FVA-Stirnradprogramm: Vergleich und Zusammenfassung von Zahnradberechnungen mit Hilfe von EDV-Anlagen (jeweils neuester Programmstand). FVA-Forschungsvorhaben Nr. 1., Forschungsvereinigung Antriebstechnik, Frankfurt am Main DIN 3990: Calculation of load capacity of cylindrical gears. Application standard for industrial gears. Part 11: Detailed method; February 1989 edition Part 12: Simplified method; Draft May 1987 Beuth Verlag GmbH, Berlin DIN 3990: Calculation of load capacity of cylindrical gears. Part 5: Endurance limits and material qualities; December 1987 Beuth Verlag GmbH, Berlin FVA-Arbeitsblatt zum Forschungsvorhaben Nr. 8: Grundlagenversuche zur Ermittlung der richtigen Hrtetiefe bei Wlz- und Biegebeanspruchung. Stand Dezember 1976. Forschungsvereinigung Antriebstechnik, Frankfurt am Main /15/
/4/
/16/
/5/
/6/
/17/
/7/
/18/
/8/
/19/
/20/
/9/
/10/
/11/
/12/
154
155

GD&T

Uploaded by

Copyright:

Available Formats

GD&T

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GD&T

Uploaded by

Copyright:

Available Formats

TECHNICAL HANDBOOK

Page 23/24 25-38 39 40/41

Section 6 Hydraulics Hydrostatics Hydrodynamics

Page 106/107 108 108-119 119-127 127-130 131-134

136 136 136/138 138 139 140

142 143-145 145/146 146/147 148 149-151 151/152

100 101 102 103 104

Table of Contents Section 1

Technical Drawings Surface Texture

Technical Drawings Surface Texture

Technical Drawings Geometrical Tolerancing

le = Sampling length lm = Evaluation length lt = Traversed length z1-z5 = Single irregularities

Suppl. 1 Roughness from to DIN values Rz to in m 4768/1

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Definition of the tolerance zone

Indication and interpretation

Definition of the tolerance zone 5.13.4 Cylindricity tolerance

Indication and interpretation

Figure 45 5.13.5 Parallelism tolerance

Figure 38 5.13.2 Flatness tolerance

Figure 40 5.13.3 Circularity tolerance

Figure 52 Figure 44 Figure 53 Figure 54

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Definition of the tolerance zone

Indication and interpretation

Definition of the tolerance zone 5.13.6 Perpendicularity tolerance

Indication and interpretation

Figure 55 Parallelism tolerance of a line with reference to a datum surface

Figure 56 Figure 64 Figure 65

Figure 57 Parallelism tolerance of a surface with reference to a datum line

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Definition of the tolerance zone

Indication and interpretation

Indication and interpretation

Technical Drawings Geometrical Tolerancing

Technical Drawings Geometrical Tolerancing

Definition of the tolerance zone

Indication and interpretation

Indication and interpretation

Figure 102 Figure 93 Figure 94 Figure 101

Technical Drawings Geometrical Tolerancing

Technical Drawings Sheet Sizes, Title Block, Non-standard Formats

Trimmed drawing sheet

Technical Drawings Drawings Suitable for Microfilming

Technical Drawings Drawings Suitable for Microfilming

0.7 0.35 0.35 0.7 0.35 0.35 0.35

Table of Contents Section 2

Standardization ISO Metric Screw Threads (Coarse Pitch Threads)

d + 2 H1 D2 d + 0.64952 P d + 1.22687 P 0.86603 P 0.54127 P 0.61343 P H 6 0.14434 P

Tensile stress crosssection As 1)

Standardization Cylindrical Shaft Ends

Cylindrical shaft ends Acc. to DIN 748/1, 1.70 edition

Cylindrical shaft ends Acc. to DIN 748/1, 1.70 edition