Zebralette User Guide
Zebralette User Guide
Zebralette User Guide
User Guide
version 2.5
TABLE OF CONTENTS
Introduction
About Zebralette __________________________________________3 Online resources _______________________________________3 Installation ____________________________________________3 File locations __________________________________________3 Presets _________________________________________________4 Load ________________________________________________4 Save ________________________________________________4 Favourites and Junk ____________________________________4 Control Bar _______________________________________________5 Knobs __________________________________________________5 Mod _________________________________________________5
6 8
Oscillator Panels
12
Waveform _______________________________________________12 Tune ___________________________________________________13 Spectral FX______________________________________________13 List of spectral effects __________________________________14 Phase __________________________________________________16 VCA ___________________________________________________17
Modulation
18
Envelope _______________________________________________18 MSEG__________________________________________________19 The Edit Window ______________________________________19 LFOs __________________________________________________20 LFO Global __________________________________________20 LFO1 _______________________________________________21 List of Modulation Sources __________________________________22
Effects
23
INTRODUCTION
Introduction
About Zebralette
Zebralette is a single oscillator plucked from Zebra2 and transplanted into a much simpler, easy-to-learn framework. As the Zebra2 oscillators are so powerful, Zebralette is a great little synth in its own right with the same pristine basic sound as Zebra2. The LFOs, MSEG and effects in Zebralette are also simplified versions of those in Zebra2. Most of the parameters are immediately visible in the window. Only the panels used for modulation parameters and effects as well as the preset browser are tabbed. Zebralette doesnt have any virtual analogue filters, but the pair of spectral effects are flexible enough to make some very squelchy filter-like sounds. After having learned how Zebralette works, you will also have learned a lot about the most important module in Zebra2...
Online resources
To check out all the other u-he products, go to the u-he website For a lively discussion of all things u-he, go to the u-he forum at kvr For sound design tips, interviews and more, go to our patchbender webzine
Installation
Go to the zebralette webpage, grab the appropriate installer for your system, doubleclick on the downloaded file and follow further instructions. For additional information, please refer to the included ReadMe file.
File locations
Like all u-he software, the Zebralette installer doesnt write anything into the Windows registry. Nor does it create hidden files or otherwise modify your system. To uninstall, delete the plugin itself, then the associated files from the following directories (the exact locations depend on your specific installation): Win: Preset files Preferences Mac: Preset files Preferences ...\VstPlugins\u-he\Zebra2.data\Presets\Zebralette\ ...\VstPlugins\u-he\ Zebra2.data\Support\ (all .txt files) MacHD/Library/Audio/Presets/u-he/Zebralette/ ~/Library/Application Support/u-he/com.u-he.Zebralette... (.* files)
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 3
INTRODUCTION
Presets
Load
To browse through Zebralettes presets, click on the Presets tab in the lower left of the window. Select a folder, then a preset. After having clicked on a preset, you should be able to use the up/down cursor keys on your computer to scroll through the others.
Save
Save Patch Select the folder where you want to put your sounds (the User folder is probably the best place you will find it at the very bottom of the folder list). Click on the Save Patch button. A window opens in which you can give your sound a name, enter your name (as author) and any details you want to add: preset description, preset usage etc.. Then confirm via the Apply button. Right-click in the Folders window whenever you need to create a new folder or refresh the list (necessary whenever folders or presets are added from Explorer / Finder). Patch Format This switch specifies the way patches are saved. The default setting is u-hes own .h2p format, recommended because it is platform-independent. To save patches in your plugin versions native format, select native. Note that .h2p files are readable text (except for a block of data at the end). More readable still is the .h2p extended format, which includes comments for each line.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 4
INTRODUCTION
Control Bar
Data Display The central display has several uses. Primarily, it shows the name of the currently selected patch. Clicking on the triangles either side of the display steps through patches. Clicking on the name will open a drop-down list containing all the patches in the current directory a convenient way of jumping to another patch without having to open the Presets panel. Voices few = 4 notes, medium = 8 notes, many = 16 notes Specifies the number of notes that Zebralette will attempt to play in parallel. As Zebralette is very CPU-friendly, this parameter is not overly important. Mode poly normal polyphonic (see Voices parameter above). mono monophonic, each new notes triggers the envelopes. legato also monophonic, but envelopes continue i.e. they are not retriggered until you leave a space between consecutive notes. Legato is essential for nuanced phrasing. PitchBend Pitch bend range up / down, from 0 to +12 semitones. The default value is +/-2.
Knobs
Values are adjusted via the usual click-and-drag, often allowing finer resolution via the SHIFT key on your computer. Note that several of the knobs are bipolar (i.e. zero is in the center so you can set negative values). Knobs can be reset to their default values via double-click, or remote-controlled / automated via right-click (MidiLearn function). Tip for wheel-mouse owners: Unless you need very fine control, you dont even have to click on knobs and switches to change values just mouseover and roll the wheel.
Mod
Dotted around the interface are several knobs all labeled Mod. These are definable modulation depth controls for the following parameters: OSC Tune, FX1, FX2, SyncTune, Phase, WaveWarp, Pan, Volume and LFO1 depth. Click on the associated button (none by default) to select a source, then adjust the value of the knob.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 5
TUTORIAL
TUTORIAL
Part 2 of 2 Go to the FX panel and select Exophase for FX2 (Exophase is about 3/4 down the list). Play a low note and slowly turn FX2 down to -80. Take FX1 back up a bit e.g. to -40. Go to the VCA panel and take Width to maximum. Click dual and change it to eleven. Play your keyboard. Go to the Tune panel and increase Detune to taste... Go to the FX panel and select PitchW as the FX2 modulation source. Turn Mod up to 60, play your keyboard and use the pitch bend wheel. Go to the top right corner and change PitchBend to 0. Click on the Effects tab (lower left, next to Modulation). In the lefthand panel (ModFX), find the knob next to the EQ button and turn it up to 50. Play a very low note and slowly turn up the knob to the right of that (low Boost). Stop when you get too much bass... Go to FX2 and remove the exophase effect: click on it and select none. Go back to the left Effects panel and slowly turn Mix up to 60% while playing low notes (you will lose some bass frequencies). Turn high Boost (two knobs to the right) up to 6.00, play a very low note and slowly turn down high CutFreq until you find a beefy sound (adjust VCA Volume if it gets too loud!) Go to the Delay panel to the right. Have a look around... Turn Mix up to 30%. Stab a high chord.... then go back to the Modulation tab. Turn R back down to 20. Stab another high chord. Click on the Effects tab again, change Sync2 (in the Delay panel to the right) to 1/4 dot. Play some more... Go to FX1 and replace LfoG1 with PitchW. Turn the Mod knob up to 70. Play chords while pushing the pitch bender...
Part 3 of 2 Immediately above the Modulation and Effects tabs is a long button. Click on it. Have a look around, try out a few of the oscillator presets. When you have found something interesting, close the floating window. Go to the Waveform panel, turn up Resolution and play with the WaveWarp value. Now work out how to modulate WaveWarp from LfoG1... Enjoy!
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 7
WAVE EDITOR
the wave selector bar, wave 11 selected The wave selector is (almost) the same as the WaveWarp knob in the Tune panel if you adjust one, the other will also move. The main difference is that, unlike the WaveWarp knob, the selector doesnt give you intermediate values (e.g. wave 1.5). Mouse operations in the Wave Selector
rearrange
(Mac) alt + drag (PC) ctrl + drag
duplicate
(Mac) alt + cmd + click on the desired target wave (PC) ctrl + alt + click on the desired target wave
WAVE EDITOR
GeoMorph mode lets you draw waveforms by defining up to 32 handles, and (if you like) adjusting the curvature of the lines connecting them. Note that the first and last handles define the level at 0 phase they cannot be deleted or moved horizontally. The minimum number of handles is 4, and all waves in the waveset adopt the same number of handles. SpectroMorph
Typical SpectroMorph wave Although it looks and feels like GeoMorph, SpectroMorph is a completely different animal! It does not depict a waveform directly, but rather its spectrum. 1023 harmonics in the horizontal axis are scaled logarithmically, for a total span of about 10 octaves. In this mode, a horizontal line spanning the width of the editor (i.e. all harmonics have equal levels) describes a bright saw wave. Mouse operations in GeoMorph and SpectroMorph modes
multiple selection
Click in the background and drag over one or more handles Shift + click on a handle to add or remove it from the selection To move all selected handles, click and drag one of them
WAVE EDITOR
Typical GeoBlend wave A single cycle is defined by 128 columns. GeoBlend is similar to GeoMorph in that it reflects the actual shape of the wave. However, when the morph function is used or WaveWarp is modulated, waveforms are not morphed, they are blended. The main advantage of GeoBlend over GeoMorph is that waveforms can be drawn freehand. Note: GeoMorph wavesets can be extracted from audio sources. A few third-party utilities are available for this purpose try googling Wav2Zebra and Blueberry Thing. SpectroBlend
Typical SpectroBlend wave The spectrum is represented by 128 (bipolar) columns. Similar to SpectroMorph except that it has fewer harmonics, which are scaled linearly for a total range of six octaves. The lower half is anti-phase, so the same harmonic in adjacent waves (e.g. 1 and 2), but with opposite phases, can cancel each other out (at exactly 1.50 in this example). This cancellation effect can be put to good use see the oscillator preset Bells Flipper. The main advantage of SpectroBlend over SpectroMorph is that you have total control over individual harmonics, including polarity. Waves are not morphed in this mode, they are blended.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 10
WAVE EDITOR
draw freehand
click + drag
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 11
OSCILLATOR PANELS
Oscillator Panels
Waveform
WaveWarp Position (index 116) in the waveset. Unlike the row of selectors below the wave editor (see the previous chapter), the WaveWarp knob lets you set intermediate values. Mod The Mod knob is for WaveWarp modulation (+/-16), and the source is selected in the field to its right (none by default). How smoothly or precisely waves are interpolated depends on the Resolution setting... Resolution This parameter controls the interval (in time) between successive waveform calculations. This trick ensures that Zebralette is very CPU-efficient compared with other spectral synthesizers that calculate their waveforms in realtime. The range is from 4 seconds (at 1.00) to less than one millisecond (at 9.00). Theoretically, high resolution leads to more precise transitions at the cost of higher CPU load. Low resolution can actually make transitions smoother (intermediates are interpolated), but can also introduce other unwanted effects (e.g. during rapid pitch-modulation). For most purpose, the default value of 5.00 is best. Oscillator Preset The button at the bottom left of the Waveform panel lets you load or save complete oscillators. Left-click to select a preset from a floating window. Right-click to open a drop-down menu. Select save oscillator settings from this menu to store the oscillator. Please note that modulation assignments (e.g. WaveWarp modulated by LFO1) are oscillator settings, but the settings in the modulation sources themselves are not. This means that an oscillator preset might not sound the same as when you saved it for instance if the original LFO1 was a 1/16 square wave and the current one is a 10s sine. Oscillator preset le locations Mac: Win: ~/Library/Application Support/u-he/Zebra2/Modules/Oscillator ...\VstPlugins\u-he\Zebra2.data\Modules\Oscillator
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 12
OSCILLATOR PANELS
Tune
the Tune panel OSC Tune Oscillator pitch offset (+/- 48 semitones). Mod Tune modulation (+/- 48 semitones). Click on the label to select a source. Detune Detune describes two slightly different jobs. In single mode, it is for fine tuning (+/- 50 cents). In Dual, Quad or Eleven modes it does not lower or raise the overall pitch of the oscillator, but spreads detuning equally. Of course you can still do normal fine tuning via SHIFT + OSC Tune. Vibrato (LFO1) The amount of pitch modulation directly from LFO1 (0 100). The maximum depth here is only +/- 50 cents for deeper vibrato, use the Mod knob with LFO1 as source. Portamento Portamento is a smooth slur (or glide) between consecutive notes. The Portamento knob adjusts the speed of this effect.
Spectral FX
spectral FX panel FX1, FX2 The waveform can be radically transformed via a pair of spectral effects routed in series (FX1 > FX2), often with very surprising results. Note that many of the effects are highly dependent on the waveform Resolution. To select an effect, click on the label below the FX knob.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 13
OSCILLATOR PANELS
Mod The two lower knobs are for modulating the depth of each spectral effect. Click on the label to select a Mod source, then adjust Mod to taste. Norm Normalize: The output level of the generated wave is analyzed (RMS), then low-level waves are boosted so that the final level would be 0dB if Norm were at 100%. High normalization values are fine for boosting most low-level waves, but please keep Norm relatively low on very spiky waves unless of course you enjoy blasting a lot of high frequencies through your system!
Brilliance Filter
Turbulence
Expander Symmetry
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 14
OSCILLATOR PANELS
Phase Xfer
A variant of PD (phase distortion) synthesis. The original waveform is not output directly, but is used as the phase response of an extra sine wave which you can hear when the value is zero. The original wave multiplies the phase response of the sine wave. The original wave adds to the phase response of the sine wave. Like phase modulation in FM synthesizers try Trajector on a pure sine. Multiplies the waveform with a harmonic, resulting in resonant sounds. Multiplies the wave spectrum with a variable harmonic, resulting in formant sounds with a number of strong peaks and troughs. Simulates hard sync by contracting the time axis then writing the waveform back into wave memory. Like Sync Mojo, except that the contracted wave is contracted again etc.. This results in a fractal waveform with even more harmonics than Sync Mojo. A classic 7-stage phaser is applied to the original wave. This effect is equally useful for static coloration or resonant sweeps. The relative amplitudes of harmonics are scaled, either to the power of 2 (negative, softer) or 3 (positive, brighter). This results in finer resolution of quieter harmonics, i.e. more precise control over the overtone structure. Similar to the Scrambler effect, but in this case the phase of the waveform is modulated by itself squared (i.e. to the power of 2). An FM triangle or square from a pure sine or absolute chaos from a sawtooth Scatter is flexible. Negative values raise an amplitude threshold below which all harmonics are faded out (Chop). Positive values raise the levels of fainter harmonics (Lift). Adds two (negative) or three (positive) copies of the original wave. The phases are randomly shifted, resulting in a subtle to dramatic effect similar to chorus. HyperComb is particularly dependent on the value of Resolution. Phase distortion, as in the 80s Casio CZ series of synthesizers... The wave acts as a function for the phase of an inverse cosine. The amount knob cross-fades between zero and full effect, so the most dramatic uses of this effect involve modulating WaveWarp. Inverts any parts of the original wave that extend above or below a variable threshold. The limits for multiple wrapping are greater for negative values.
Exophase Scale
Scatter
ChopLift
HyperComb
PhaseDist
Wrap
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 15
OSCILLATOR PANELS
Phase
the Phase panel SyncTune Offset for the oscillator-internal hard-sync effect. This classic analogue sync adds a lot of upper harmonics, and is probably why it was often used to imitate screaming guitar sounds back in the shoulder-padded and hairsprayed 1980s. Sync Switches the sync effect on / off. Mod (left) User-definable SyncTune modulation. Reset Reset causes the wave to start at the same position (set by Phase) every time a note is played. Phase Adjusts oscillator phase for the following two parameters: PWM The PWM switch adds an upside-down copy of the oscillator to itself... Mod (right) ... and this is user-definable phase modulation. If the PWM switch is on, the effect is very similar to classic pulse width modulation (because only the phase of the original wave is modulated).
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 16
OSCILLATOR PANELS
VCA
This is Zebralettes Output panel....
Pan Pans the sound to the left or right. Stack Mode single / dual / quad / eleven Selects single or stacked (2, 4 or 11) oscillators. The eleven mode could be called a superwave (not a supersaw, hypersaw, terrorsaw etc.) because the stacking effect works with any wave the oscillator can deliver. Mod (left) User-definable Pan modulation. Click on the label to select a source. Width If the oscillator is in dual, quad or eleven mode, this knob controls the stereo separation of the stacked oscillators. Does nothing if Zebralette is in Single mode. Volume Main output level. Envelope selector Choose either the Gate or Env1 as your audio envelope. Selecting the gate here frees up the envelope for other duties. Note: Gate is a simple on/off whenever a note is played/released, but with a short but noticeable release time. Mod (right) User-definable Volume modulation. Scales the level from 0% through 100% (center) to 200%. Click on the label to select a source.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 17
MODULATION
Modulation
Envelope
modulation panel, envelope Shape The switch below the panel name sets the curvature of all time-based envelope stages: quadric linear v-slope Exponential curves. Attack is convex, Decay and Release are concave. Straight lines, as in the image below. Linear envelopes can sound unnatural. Exponential curvature via the Slope parameter:
Slope Only works in v-slope mode. The far left position is extremely concave, -50 is close to quadric, the center is linear, the far right is extremely convex. A Attack: The time it takes to rise from zero to maximum D Decay: The time it takes to drop from maximum to the Sustain level S Sustain: The level after Decay. Normally stays at that position until the note is released. F/R Fall/Rise: Fall to zero (negative values) or rise to maximum (positive values). Extreme values make this transition very short, values close to zero (use SHIFT to fine-tune) can be quite long. R Release: The time it takes to drop to zero after a note is released. Vel Velocity for envelope dynamics: keyboard velocity scales the envelopes output level.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 18
MODULATION
MSEG
modulation panel, MSEG The Multi Stage Envelope Generator is a complex modulation source offering total control of the shape as well as continuous control over the timing. Many different uses for MSEGs can be found in the factory presets. If you find shapes you would like to use elsewhere, save them as Presets... MSEG preset MSEG settings can be loaded and saved. Click on the MSEG button to load, right-click to select from a drop-down menu or save to the current folder. The Zebralette MSEG has no rate / synchronisation controls (use Zebra2 for this). MSEG preset locations: Mac: MacHD/Library/Application Support/u-he/Zebra2/Modules/MSEG PC: ...\VstPlugins\u-he\Zebra2.data\Modules\MSEG Velocity-MSEG For dynamic envelopes velocity scales the level of MSEG output. Switches Below the editing window are three small blue icons. From left to right, these are: Single......... moves individual handles, all other handles remain fixed Shift.............moves individual handles, all following handles also move Draw........... moves multiple handles vertically click on a handle and draw Handles jump to the nearest unit snap and value snap positions (see Context Menu).
MODULATION
Context Menu (right-click on a handle) Remove Point, Loop Start and Loop End are self-explanatory. To make a loop of zero length (you might need this from time to time), simply delete the loop end handle. Context Menu (right-click in the background) copy / paste................... clipboard functions for the waveset half size........................... shortens the envelope double size.....................lengthens the envelope upside down.................. inverts the envelope unit snap......................... horizontally restricts new input to 3, 4, 6 or 8 steps per unit value snap......................vertically restricts new input to 12, 24, 36, 48 or 15 levels quantize to snap..........quantizes all handles to the nearest step (see unit snap) unit spacing................... distributes all handles to successive units even spacing.................evenly distributes all handles between the leftmost and rightmost. pointer.............................. resolution of the position indicator. Reverts to Course by default
LFOs
Zebralette has two LFOs (low frequency oscillators). Alongside envelopes, LFOs represent THE classic modulators for vibrato or any kind of cyclic movement.
LFO Global
The global LFO is a bit simpler than LFO1 (see below). LFO Global does not retrigger per voice, it is quasi monophonic. Sync LFO rate: 0.1s, 1s, 10s...... absolute times adopted directly from Zebra2, no scaling factor yet! 1/64 8/1............ sync to song tempo, up to eight bars. Includes dotted and triplet values. Waveform sine......................... pure sine wave triangle.................. pure triangle wave saw up.................. rising saw (ramp) saw down............ falling saw sqr lo-hi................ square wave, restarted at the lower level sqr hi-lo................ square wave, restarted at the higher level rand hold..............random steps rand glide............ random curves Phase Sets the position within the LFO cycle at which it will Restart (see below). This parameter is meaningless if Restart is set to off.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 20
MODULATION
Restart off, each bar...32 bars: The GLFO is automatically restarted after a defined number of bars. Future versions of Zebralette may include gate-retriggering (like in the standard LFO module).
LFO1
This module is called a voice (polyphonic) LFO because, unlike the global one, it is instantiated per voice. Every note you play gets its own LFO. So the main advantage is that different notes in a chord can have different phases. Sync LFO rate. The list of synced values includes dotted and triplet note lengths. 0.1s, 1s, 10s...... absolute times adopted directly from Zebra2, no scaling factor yet! 1/64 8/1............ sync to song tempo, up to eight bars Waveform sine......................... pure sine wave triangle.................. pure triangle wave saw up.................. rising saw (ramp) saw down............ falling saw sqr lo-hi................ square wave, restarted at the lower level sqr hi-lo................ square wave, restarted at the higher level rand hold..............random steps rand glide............ random curves Phase Sets the position within the LFO wave where it will restart each time a new note is played. Phase is ignored if Restart is set to free. Restart sync: LFO1 phase is offset for each note to synchronize best with the song gate: LFO1 starts at the same phase for each note (see Phase above) single: LFO1 becomes monophonic, it has the same phase for all notes random: LFO1 starts at a random phase for each note Depth Mod This label refers to both the field above it as well as the knob to the right. User-definable amplitude modulation of LFO1. Note that LFO1 is directly connected to Vibrato in the Tune panel: For traditional vibrato depth control, set the source to ModWhl. Delay Actually a ramp-up time for the LFO1 amplitude. Typically used for delayed vibrato. However: If you need an extra little envelope at the expense of an LFO, try this: Set Sync to 8/1, set Reset to Gate and adjust Delay (ramp time). Use negative modulation levels for ramp-down envelopes.
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 21
MODULATION
none ModWhl PitchW Breath Xpress LfoG1 Gate KeyFollow KeyFollow2 Velocity Pressure Env1 MSEG Lfo1
no modulator modulation wheel, MIDI CC#01 pitch wheel (pitch bender) breath control, MIDI CC#02 expression control, MIDI CC#11 global Low Frequency Oscillator simple on/off envelope MIDI note number. Breakpoint is E2 in Zebralette this is practically the same as KeyFollow MIDI velocity aftertouch (channel or poly, depending on which is received first) envelope multi-segment envelope generator per voice Low Frequency Oscillator
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 22
EFFECTS
Effects
ModFX
the ModFX panel Analogue purists may shudder at the mention of built-in chorus effects (which often signify a lack of beef in other departments), but we believe no synthesizer should be without one. So here it is... Mode Chorus....... chorus / flanger using short delay lines Phorus....... chorus / flanger using allpass filters Phaser....... classic phaser unit Center / Speed / Depth Center........ nominal delay time / allpass cutoff, i.e. before modulation Speed........ modulation LFO rate (from 0.001Hz to 1Hz) Depth......... modulation LFO amount Feedbk Bipolar feedback control for flanger type resonances especially at extreme values. Mix & Stereo Mix............... balance between dry and wet signal Stereo........ modulation LFO phase offset between the two stereo channels. Note that 50% is often more stereo than 100%. Quad & Q-Phase Quad.......... volume of an extra chorus effect, with independent LFO Q-Phase... modulation LFO phase offset (see Stereo above) for the Quad effect Equalizer This unique feature can e.g. preserve the stereo image of bass frequencies via low cut, while at the same time making the chorus effect sound less harsh via high cut. EQ............... switches ModFX equalization on/off. LowFreq....low crossover frequency HiFreq........ high crossover frequency Boost.......... cut/boost controls for the two frequency ranges
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 23
EFFECTS
Delay
the Delay panel The delay module in Zebralette is the same as in Zebra2, except that the parameters are not freely modulatable. It has four delay lines, each with time scaling and pan controls. Two flavours of feedback with inserted low and highpass filters can run at the same time, feeding each other... Mode stereo 2...........stereo delay, uses delay 1 and 2 only multitap 4....... all four delays in parallel dubby 2+2..... like two instances of stereo 2 in series serial 2............ ping-pong delay, uses delay 1 and 2 only Feedback & X-back Normal regeneration, cross-regeneration. In multitap mode, X-back is 1>2, 2>3, 3>4, 4>1 Mix Cross-fade between the dry and wet signal Lowpass & Hipass Simple filters in the feedback paths for changing the tonal quality of successive repeats. Sync1...Sync4 The button above each % knob sets either a synchronized note value (1/64th to 1/1 triplet) or absolute time (nominally 1 second). % The ratio (%) knobs scale the Sync values from 0% to 200%. Pan A panorama position for each delay line.
The End
Many thanks to u-he forum members for ideas and proof-reading Howard Scarr 2010
toc tutorial editor waveform tune spectral phase vca envelope mseg lfo modfx delay ! 24