ABSOLUTE ROTARY ENCO DER ETHERNET -TCP/IP, -UDP

Main Features - Compact and heavy duty industrial model - Communication via standard protocols - Integrated web server - Interface: - Housing: - Full shaft: - Resolution: - Code: Ethernet-TCP/IP, -UDP 58 mm 6 or 10 mm / hollow shaft15 mm max. 30 Bit = 1,073,741,824 steps over 16384 revolutions Binary

Programmable Parameters - Used scope of physical resolution - Total scaled resolution - Preset value - Direction of rotation (complement) - Different modes for output of position, velocity and time stamp - Network- and e-mail- parameters

Mechanical Structure - Flange and housing, Aluminum and Brass respectively - Stainless steel shaft - Precision ball bearings with sealing rings
- Code disc made of durable and unbreakable

Electrical Features - Status indication with LEDs - Temperature insensitive IR-Opto-receiver-ASIC - Polarity inversion protection - Over-voltage-peak protection

plastic - Robust electrical connection with M12-connector

AMERICA FRABA Inc. 1800 East State Street, Suite 148 Hamilton, NJ 08609-2020, USA T +1-609-750-8705, F +1-609-750-8703 www.posital.com, [email protected]

EUROPE POSITAL GmbH Carlswerkstrasse 13c D-51063 Kln, Germany T +49 221 96213-0, F +49 221 96213-20 www.posital.eu, [email protected]

ASIA FRABA Pte. Ltd. 60 Alexandra Terrace Singapore 118502, Singapore T +65 65148880, F +65 62711792 www.posital.sg, [email protected]

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Technical Data
Electrical Data Supply voltage Power consumption EMC Bus connection Transmission rate Accuracy of division Step frequency LSB Cycle time Electrical lifetime Device addressing Mechanical Data Housing Lifetime Max. shaft load Inertia of rotor Friction torque RPM (continuous operation) Shock (EN 60068-2-27) Permanent shock (EN 60028-2-29) Vibration (EN 60068-2-6) Weight (standard version) Aluminum, optional stainless steel Dependent on shaft version and shaft loading refer to table Axial 40 N, radial 110 N 30 gcm
2

10 - 30 V DC (absolute limits) max. 4 Watt Emitted interference: EN 61000-6-4 Noise immunity: 10/100 MBit LSB (up to 12 Bit), 2 LSB (up to 16 Bit) max. 800kHz (valid code) > 1 ms (Cyclic mode), > 5 ms (Change of state) > 10 h Programmable IP-Address and Network parameters
5

EN 61000-6-2

Ethernet TCP/IP and UDP

3 Ncm (without shaft sealing) max. 12,000 RPM 30 g (halfsine, 11 ms) 10 g (halfsine, 16 ms) 10 g (10 Hz ... 1,000 Hz) Singleturn: Multiturn: 500 g 700 g Clamp (C) 10 mm 20 mm Hollow shaft (B) 15 mm 15 mm / 30 mm

Flange Shaft diameter Shaft length hollow shaft depth min. / max.

Synchro (S) 6 mm 10 mm 10 mm 20mm -

Page 2

E Info OCD ETA1

Version: 03/07

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Minimum (mechanical) lifetime Flange C10 (Clamp flange 10 x 20) S10 (Synchro flange 10 x 20) S6 (Synchro flange 6 x 10) without shaft sealing Lifetime in 10 revolutions with Fa / Fr 40 N / 60 N 247 262 822 40 N / 80 N 104 110 347 40 N / 110 N 40 42 133
8

S6 (Synchro flange 6 x 10) with shaft sealing: max. 20 N axial, 80 N radial

Environmental Conditions Operating temperature Storage temperature Humidity Protection class (EN 60529) 0 .. +60C - 40 .. + 85 C 98 % (without liquid state) Casing side: IP 65 Shaft side: IP 64 (optional with shaft sealing: IP66)

Version 03/07

E Info OCD ETA1

Page 3

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Interface
Protocols The communication is based on Ethernet-TCP/IP or UDP at data rates of 10 Mbps or 100 Mbps. TCP/IP stacks are available in all common operating systems. A data exchange in heterogeneous networks is possible by using the IP protocol. The control system send commands to and receive data from the Encoder by the exchange of commands in ASCII text. Java Applets providing a graphical user interface (GUI) and documentation is provided on a Web server integrated in the Encoder for convenient configuration and diagnosis. Based on http, html and Java applets the GUI and all documents can IP

be displayed on all common web browsers. In addition to the encoder parameters all necessary network parameters, like the IP-address, can be set. All parameters are saved in a non volatile memory so that the configuration is available promptly after a restart. Another feature of the web server is the optional output of messages via the SMTP protocol. In this way parameters and diagnosis messages can be sent by e-mail. As UDP does not provide a secure transmission of data, only polling the encoder and receiving position values are available in the UDP mode.

A data exchange in heterogeneous networks is possible by using the well known internet protocol "IP". The universal IP addressing simplifies the implementation of communication processes significantly.

TCP / UDP

TCP-Protocol assures an error free data transmission. For an enhanced real-time performance, the UDP protocol can be used alternatively.

http smtp

Via http a common web browser can be used for read out, configuration and diagnosis of the encoder. Via smtp protocol messages of the encoder can simply be sent by email.

Page 4

E Info OCD ETA1

Version: 03/07

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Programmable Parameters The encoder is able to provide three different kinds of output data: the position value, a velocity value and a time stamp. These can be used in arbitrary combinations. The following parameters can be modified: Parameter Description

Used scope of physical resolution Specifies the part of the physical resolution used for the encoder in (parameter 1.) physical steps. If e.g. for an encoder with a resolution of 8,192 steps per revolution 16,384 is chosen, the encoder will count 8,192 steps per revolution (if Total scaled resolution is set to the same value as Used scope of physical resolution) and start with zero again after 2 revolutions. If this value is not set to a value which results in an integer division with the total physical resolution, the encoder value will jump to zero when passing the physical zero point. Total scaled resolution (parameter 2.) Specifies the scaled resolution which is used over the area of physical steps defined by Used scope of physical resolution. If e.g. the encoder is set as described above and Total scaled resolution is set to 10, the encoder will count 10 steps over the physical steps defined with Used scope of physical resolution, i.e. 5 steps per revolution. Code sequence The parameter Code Sequence (Complement) determines whether the output code increases or decreases when the axis is turned clockwise. Preset value Offset value The preset value is the desired output value for the actual position of the axis. The actual output value will be set to this preset value. This variable makes it possible to directly change the offset calculated and set by the preset function.

Max. physical position value

Max. needed position value (parameter 2.)

Wanted zero crossing (parameter 1.)

Physical zero crossing

Version 03/07

E Info OCD ETA1

Page 5

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

The integrated web server of the encoder contains different web pages for information purposes and to parameterize the encoder. The html-page for configuration and diagnostics of the encoder provides the following website:

Pinning
Connector Ethernet 4 pin female, D-coded Pin Number 1 2 3 4 Signal Rx + Tx + Rx Tx Connector power supply 5 pin male, A-coded Pin Number 1 2 3 4 5 Sketch on encoder view Signal +24 V +24 V 0V 0V PE

4 5

Page 6

E Info OCD ETA1

Version: 03/07

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Mechanical Drawings
Synchro Flange (S) available in 2 versions
Single-Turn=77, Multi-Turn=88 35 3xM4x6

Synchro flange Version S06 Version S10

d / mm 6f6 10h8

l / mm 10 20

3x 12 0

59 (61)*

23

50 f7

58

60

* Edelstahl / Stainless steel 3 3 4 24

Clamp Flange (F)

30

Single-Turn=77, Multi-Turn=88 35 3xM3x6 10 3xM4x6

68

60

42

3x 12 0

59 (61)*

23

36 f7

10 h8

58

53

60

68

4 8

18

3x12 0

3 3 * Edelstahl / Stainless steel 24

Version 03/07

E Info OCD ETA1

Page 7

15

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Hollow shaft (B)

59 (61)*

23

F7

60

60

20

15

68

20

3,2

Anlagekante an Momentensttze

* Edelstahl / Stainless steel 24

Max. W ** = 30 Min. W ** = 15
** Welleneinstecktiefe (hollow shaft depth)

Mounting instructions The clamp ring should only be tightened after the shaft of the driving element was inserted into the hollow shaft. The diameter of the hollow shaft can be reduced to 12 mm, 10 mm or 8 mm by using an adapter (this reducing adapter can be pushed into the hollow shaft).

Maximum radial and axial misalignment of the drive shaft: axial static dynamic 0.3 mm 0.1 mm radial 0.5 mm 0.2 mm

Page 8

E Info OCD ETA1

Version: 03/07

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Models/Ordering Description
Description Optocode Interface Version Code Type Key OCDEthernet 2xM12 ET ET A1 B1 B 00 12 14 13 16 10 mm 6 mm 10 mm 15 mm C10 S06 S10 B15 0 S C PRM __ B__ _____ _PRM

Integrated hub, 3xM12 * Binary

Revolutions (Bits) Singleturn Multiturn (4,096 revolutions) Steps per revolution Flange (Bits) / Shaft diameter Multiturn (16,384 revolutions) 8,192 65,536 Clamp flange, full shaft: Synchro flange, full shaft: Blind hollow shaft, hollow shaft : Mechanical options Connection Without Shaft sealing (IP66) Customized M12 connector

Standard = bold, further models on request * available from III/06

Version 03/07

E Info OCD ETA1

Page 9

ABSOLUTE ROTARY ENCO DER ETHERNET-TCP/IP, -UDP

Accessories and Documentation Description Male cable connector Female cable connector Coupling * Clamp disc * Clamp half-ring * Reducing adapter ** M12, 4 pin, D-Coded M12, 5 pin Drilling: 10 mm Drilling: 6 mm Set = 4 pcs. Set = 2 pcs. 15 mm to 14 mm 15 mm to 12 mm 15 mm to 11 mm 15 mm to 10 mm 15 mm to 8 mm User manual * User manual * * ** Type PAM4 PAM5 GS 10 GS 06 SP 15 SP H RR14 RR12 RR11 RR10 RR8

Installation / configuration manual, English UMD-ETA1 Installation / configuration manual, German UME-ETA1

These can be downloaded free of charge from our homepage www.posital.de. usable only for full shaft

*** usable only for hollow shaft, in stainless steel available too We do not assume responsibility for technical inaccuracies or omissions. Specifications are subject to change without notice.

Page 10

E Info OCD ETA1

Version: 03/07