TSA

Swirl Diffuser

Horizontal radial or alternatively vertical compact swirl jet air supply, also suitable for heating applications Also well suited to large and high spaces Supply air pattern can be adjusted either manually or controlled by actuator High induction swirl jet ensures efficient mixing and fast reduction of air velocity Installation using plenum or directly to ductwork

Accessories Balancing plenum with adjustment function (PLC) or also with measurement function (TRI) Actuator (with 24 VAC power supply and proportional 010 VDC control signal or alternatively self actuating wax-bulb) for the direction of airflow pattern

MATERIAL AND FINISHING

PART Casing Deflector ring or cylinder Front vane panel Finishing MATERIAL Steel Steel Steel Polyester painted White RAL 9010 Special colours available NOTE

TSA - Swirl Diffuser

186

20/TSA/3500/1107/EN

QUICK SELECTION
Pa qv TSA-250(R) l/s m 3/h LpA DPst DPtot Ld Lmin L0.2 TSA-315(R) LpA DPst DPtot Ld Lmin L0.2 TSA-400(R) LpA DPst DPtot Ld Lmin L0.2 TSA-500(R) LpA DPst DPtot Ld Lmin L0.2 TSA-600(R) LpA DPst DPtot Ld Lmin L0.2 LpA values presented with room attenuation 4 dB (red 10m 2 sab). When using room attenuation 8 dB (red 25m 2 - sab): LpA - 4dB. Pa LpA Supply air cooling capacity, W A-weighted sound pressure level, reduced by total equivalent absorption surface of 10m 2, dB(A) red 10m 2 - sab Static pressure drop, Pa DPtot Ld 1200 100 360 23 19 21 2,2 2,6 2,3 1440 120 432 29 27 30 2,4 3,4 2,8 1800 150 540 37 42 47 2,6 4,8 3,4 23 14 16 2,4 3,4 2,8 2160 180 648 45 60 68 3,0 6,2 4,2 28 20 23 2,6 4,4 3,4 2640 220 792 54 90 102 3,4 8,0 5,2 35 30 35 3,2 6,0 4,2 43 46 53 3,4 7,8 5,2 25 16 19 3,0 5,6 5,0 55 77 89 4,2 10,6 6,8 34 27 32 3,6 8,0 6,4 43 45 52 4,2 10,8 8,2 26 17 20 3,2 8,2 6,0 55 79 93 5,0 15,0 11,0 36 30 36 4,0 11,6 8,2 22 11 13 3,0 8,8 6,4 45 47 56 4,8 15,0 10,2 29 17 21 3,6 11,4 8,0 52 68 80 5,4 18,4 12,2 35 25 30 4,2 14,2 9,6 42 37 45 5,0 17,8 11,8 52 60 73 5,8 23,2 15,0 3240 270 972 4200 350 1260 5400 450 1620 7200 600 2160 9000 750 2700 10800 900 3240 13200 1100 3960 16800 1400 5040

DPst

Total pressure drop, Pa Distance from the supply unit, at which air jet detaches from ceiling, m Lmin Minimum distance between central lines of two supply units, m (V3 = 0,25m/s at 1.8m height) L0.2 Isotermal throw length, m when residual velocity of supply air jet 0,2 m/s Room temperature (Tr) = 24 C Supply air temperature (Ta) = 14 C Room height = 2,8 m

TSA - Swirl Diffuser

187

20/TSA/3500/1107/EN

QUICK SELECTION
Pa qv TSA-250(C) l/s m 3/h LpA DPst DPtot L0.2 TSA-315(C) LpA DPst DPtot L0.2 TSA-400(C) LpA DPst DPtot L0.2 TSA-500(C) LpA DPst DPtot L0.2 TSA-600(C) LpA DPst DPtot L0.2 LpA values presented with room attenuation 4 dB (red 10m sab). When using room attenuation 8 dB (red 25m 2 - sab): LpA - 4dB.
2

1440 120 432 22 22 26 2,8

1800 150 540 30 35 40 3,6 17 12 14 2,4

2160 180 648 37 50 58 4,4 22 17 20 3,0

2640 220 792 46 75 87 5,6 28 26 30 4,0

3120 260 936 53 104 121 6,8 34 36 43 4,8 19 12 15 3,0

3600 300 1080

4200 350 1260

4800 400 1440

5400 450 1620

6000 500 1800

7200 600 2160

9000 750 2700

10800 900 3240

13200 1100 3960

15600 1300 4680

39 48 57 5,6 23 16 19 3,6

44 65 77 6,8 28 22 26 4,2

49 85 101 8,0 33 28 34 5,0 21 10 12 2,8

53 108 128 9,0 37 36 44 5,8 24 13 16 3,2 42 44 54 6,6 28 16 20 3,8 49 64 78 8,2 33 23 28 4,6 22 9 11 2,6 41 35 44 6,2 29 14 17 3,4 48 51 63 7,6 34 20 25 4,2 41 30 37 5,2 47 42 52 6,4

Pa LpA

DPst

Supply air cooling capacity, W A-weighted sound pressure level, reduced by total equivalent absorption surface of 10m 2, dB(A) red 10m 2 - sab Static pressure drop, Pa

Total pressure drop, Pa Distance from the supply unit, at which air jet detaches from ceiling, m L0,2 Isotermal throw length, m when residual velocity of supply air jet 0,2 m/s Room temperature (Tr) = 24 C Supply air temperature (Ta) = 14 C Room height = 2,8 m DPtot Ld

DIMENSIONS
NS 250 315 400 500 630 D 249 314 399 499 629 W 382 475 593 735 917 H 221 233 246 264 286

10

176 H

TSA with electrical actuator

NS 250 315 400 500 630 D 249 314 399 499 629 W 382 475 593 735 917 H 221 233 246 264 286 H3 430 459 486 499 524
H3

176

TSA with wax-bulb actuator

NS 250 315 400 500 630 D 249 314 399 499 629 W 382 475 593 735 917 H 221 233 246 264 286 H2
H2

302 329 342 367

176

273

10

TSA - Swirl Diffuser

188

10

20/TSA/3500/1107/EN

Compact jet

Radial Jet

Function The TSA is a high induction swirl diffuser with an adjustable flow pattern. The horizontal radial swirl jet is used mainly in cooling applications that use cool supply air or for ventilation with isothermal supply air. The vertical compact swirl jet with warm supply air is used in heating applications. Adjustment of the supply air pattern is effected by moving the internal adjustment element (cylinder). It is also possible to change from cooling mode to heating mode by adjusting the flow pattern using an electric or wax bulb actuator. The recommended maximum temperature differences between room and supply air temperatures are +15 C for heating and -15 C for cooling applications.

Product models TSA with electric actuator Siemens GDB161.2E/HA actuator with 24 VAC power supply and proportional 010 VDC control signal TSA with wax-bulb actuator TSA can be equipped with a wax-bulb actuator, which work without any power supply. The cylinder position changes according to the temperature of supply air. The temperature range of the wax-bulb actuator is about 20 C to 27 C. The time taken to change from radial to compact jet (or the other way around) is 10 - 20 minutes. When warm air is supplied the piston of the wax bulb actuator keeps moving until the TSA supply air pattern is vertical. When cold air is supplied, the TSA supply air pattern is changed back to horizontal by means of a spring.

TSA - Swirl Diffuser

189

20/TSA/3500/1107/EN

Installation The diffuser is connected either directly to the duct by screwing or riveting or alternatively to TRI or PLC balancing plenum. The front vane panel can be reattached Remove the screws through the front vane panel (sizes 250 and 315) or between the cylinder and casing (sizes 400, 500 and 630), turn and hold the front vane panel to remove. Take care during installation to ensure that the cylinder can move freely and that the actuator has adequate installation space. There should be at least 50 mm clearance space above the top of the device when the cylinder is in the lowest position. The connection and fixing rivets or screws may not be located more than 50 mm below the upper edge of the diffuser. A minimum safety distance upstream of the diffuser
TSA with PLC plenum TSA 500 630 D1 500 630 PLC PLC 500 PLC 630 H1 810-950 850-990 W1 620 785

Installation with plenum

TSA with TRI plenum TSA 250 315 400 D1 200 250 315 TRI TRI-200-250 TRI-250-315 TRI-315-400 H1 390-535 465-610 525-670 W1 310 400 500

It is recommended that the distance between the PLC plenum and TSA sizes 500 and 630 is at least 1xD to ensure proper diffuser operation.

Ensure that the actuator has adequate installation space when installed in TRI plenum. It is recommended to install the collar outwards. The technical performance for the combination of supply air diffuser and TRI plenum is presented separately for the two different installations. See HIT Design software.

0 10

W1

TSA - Swirl Diffuser

190

H1

of 3xD is recommended.

20/TSA/3500/1107/EN

Adjustment CODE 1 2 3 4 DESCRIPTION Control knob Casing Front vane panel Cylinder
qv = k * pm

Pass the tubes and control spindle through the front vane panel. Measure the differential pressure using a manometer. The flow rate is calculated using the formula below.

Throw pattern adjustment The supply air jet is adjusted by changing the position of the cylinder. When you turn the knob clockwise the throw pattern is changes from radial to compact. Airflow adjustment It is not possible to adjust the airflow in TSA itself. In order to enable airflow adjustment and measurement of airflow rate it is recommended that you connect the diffuser TSA 250, 315 and 400 to the TRI balancing plenum. The supply flow rate is determined by using the measurement and adjustment module MSM. Adjust the airflow rate by rotating the control spindle until the desired setting is achieved. Replace the tubes and spindle in the plenum.

TSA - Swirl Diffuser

191

20/TSA/3500/1107/EN

Supply, radial jet, ceiling installation flush to the ceiling

TSA-250, TSA-315, TSA-400

TSA-500, TSA-630
TSA-500(R) TSA-630(R)

Selection example : Requirements : qv = 350 l/s LpA < 35 dB(A) L0,2 < 8,0 Horizontal jet Selection : TSA-400 LpA = 34 dB(A) L0,2 = 8,0 DPtot = 32 Pa

Note : For exposed installation horizontal the throw pattern can be reduced by approximately 30 %, of the value given in the diagram. With isothermal air, the throw pattern can be calculated for other terminal velocity by using correction factor : L0.3 = L0.2 x 0.67 L0.4 = L0.2 x 0.5 With non-isothermal air, the throw pattern changes due to air density. Please refer to next page or to the Halton HIT. CD-rom calculation program.

SOUND LEVEL DATA

Radial Jet TSA-250(R) qv (l/s) 108 124 141 160 163 189 217 248 271 316 364 414 433 505 583 664 (m 3/h) 389 446 508 576 587 680 781 893 976 1138 1310 1490 1559 1818 2099 2390 DPst (Pa) 21 28 37 47 17 22 30 39 16 22 29 38 16 21 28 37 DPtot (Pa) 24 32 42 54 19 26 34 45 19 26 34 44 18 25 33 44 16 22 30 39 dB (red F (Hz) 125 29 32 36 39 29 32 36 39 28 33 37 41 29 33 37 40 29 34 37 41 10m 2 250 26 29 32 35 27 30 33 35 26 30 33 36 26 29 32 35 500 26 29 32 35 28 31 34 36 29 32 36 39 28 31 34 37 1000 26 31 36 41 25 31 36 41 24 31 37 42 25 31 36 41 2000 19 26 33 39 17 24 31 38 15 22 28 34 17 24 31 38 4000 15 20 25 30 13 17 22 26 14 19 24 28 13 19 24 29 8000 15 18 21 23 14 17 21 24 15 18 22 25 14 18 21 24 LpA [dB(A)] 25 30 35 40 25 30 35 40 25 30 35 40 25 30 35 40 NR 22 27 32 38 21 27 32 37 21 27 33 38 21 27 32 37 NC 20 25 31 36 19 25 31 36 19 25 31 37 19 25 31 36

TSA-315(R)

TSA-400(R)

TSA-500(R)

660 2376 13 776 2794 19 896 3226 25 1029 3704 33 LpA values presented with room attenuation 4 NR/NC noise criteria

TSA-630(R)

26 28 25 30 31 31 33 34 36 36 37 41 sab). When using room

16 12 14 25 21 19 24 18 18 30 27 25 31 23 21 35 32 31 37 28 24 40 37 36 attenuation 8 dB (red 25m 2 - sab): LpA - 4dB.

TSA - Swirl Diffuser

192

20/TSA/3500/1107/EN

Pressure drop, throw pattern and sound data

Supply, compact jet, ceiling installation

TSA-250, TSA-315, TSA-400

TSA-500, TSA-630

Selection example : Requirements : qv = 350 l/s LpA < 30 dB(A) L0,2 < 16,0 Selection : TSA-400 LpA = 28 dB(A) L0,2 = 15,0 DPtot = 26 Pa

Note : With non-isothermal air, the throw pattern changes due to air density. Please refer to next page or to the Halton HIT software.

SOUND LEVEL DATA

Compact Jet TSA-250(C) qv (l/s) 130 149 170 192 TSA-315(C) 199 232 270 311 TSA-400(C) 319 370 425 481 TSA-500(C) 458 539 628 726 TSA-630(C) 663 783 918 1065 (m 3/h) 468 536 612 691 716 835 972 1120 1148 1332 1530 1732 1649 1940 2261 2614 2387 2819 3305 3834 DPst (Pa) 26 34 45 57 21 29 39 51 18 24 32 41 13 18 25 33 11 15 21 28 DPtot (Pa) 30 40 52 66 25 34 46 61 22 30 39 50 16 23 31 41 14 19 26 35 F (Hz) 125 29 32 35 37 30 31 33 35 29 32 34 37 30 33 35 38 30 33 36 38 250 26 29 32 35 27 31 34 37 26 30 33 36 26 29 32 35 26 29 32 36 500 26 29 33 36 27 32 36 40 29 32 35 38 28 31 35 38 28 32 35 38 1000 23 29 34 39 23 29 34 39 22 29 35 41 23 30 36 41 23 30 36 41 2000 22 28 34 40 21 27 33 39 20 26 32 37 20 26 31 37 20 26 31 37 4000 18 22 26 30 16 19 22 25 17 21 25 29 16 21 25 29 15 20 25 29 8000 17 18 20 22 14 15 16 17 17 20 22 25 16 19 22 25 16 19 22 25 LpA [dB(A)] 25 30 35 40 25 30 35 40 25 30 35 40 25 30 35 40 25 30 35 40 21 28 34 39 21 27 33 38 20 25 31 37 20 26 32 37 20 26 32 37 19 25 31 37 18 24 30 36 19 23 30 36 18 24 30 36 18 24 30 36 NR NC

LpA values presented with room attenuation 4 dB (red 10m 2 - sab). When using room attenuation 8 dB (red 25m 2 - sab): LpA - 4dB. NR/NC noise criteria

TSA - Swirl Diffuser

193

20/TSA/3500/1107/EN

Pressure drop, throw pattern and sound data

Servicing Remove the front vane panel and clean the diffuser by wiping it with a damp cloth, instead of immersing it in water. Option with balancing plenum

Product code TSA-D D = Connection size 250, 315, 400, 500, 630

Specifics and accessories Remove the measurement and adjustment module by pulling gently the shaft; (not the control spindle or measurement tubes!). Wipe the parts with a damp cloth, instead of immersing them in water. Remount the measurement and adjustment module by pushing the shaft until the module meets the stopper. MO = Actuator type Suggested specifications The diffuser shall consist of a frame with fixed internal profiled vane rings and a movable deflector ring or cylinder for throw pattern selection. The front vane panel, the movable cylinder and the frame shall be made of powder painted steel, with a white (RAL 9010) as standard colour. The airflow pattern shall be adjustable automatically using an electrical or wax-bulb actuator, (in applications where both heating and cooling are required.) NA M2 M3 No actuator 24 VAC actuator, 0...10 VDC control signal Wax-bulb actuator CO = Colour W X White Special colour

Code example TSA-250, CO=W,MO=NA Sub products PLC Plenum (Ceiling diffusers) TRI Plenum (Diffusers)

TSA - Swirl Diffuser

194

20/TSA/3500/1107/EN