MEC1/2 COURSE: ELECTROTECHNOLOGY

Part A: Learning Elements 1. 2. 3. 4. Electric and Electronic Components Electric Circuit Principles Electromagnetism Electrical Machines

Element 1 1. Understands the physical construction and characteristics of basic components. Performance Criteria 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 Compares the characteristics of conductors, semi-conductors and insulators in terms of the Electron Theory. Defines the basic quantities of electricity, eg, charge, current, emf, potential difference, energy and power. Describes resistance, inductance and capacitance in terms of physical dimensions and materials. Solves numerical problems relating R, L and C to their physical parameters. Appreciates how temperature affects conductors, semi-conductors and insulators. Defines temperature coefficient of resistance at O(xo) and also at a stated temperature (xt) . Calculates change in conductor resistance using the temperature coefficients in 1.6. Draws and labels the principal parts of a lead acid cell. Describes (without using chemical formulae) the action of charge and discharge on the components of the cell. Explains how the state of charge of a lead acid cell may be measured using a hydrometer. Draws and labels the principal parts of an alkaline cell, Nickel iron or nickel cadmium. Explains how the state of charge may be assessed for alkaline cells. Compares lead acid and alkaline cells on the basis of: (a) voltage per cell; (b) performance under poor conditions of charge/discharge; (c) retention of charge; (d) effect of temperature; (e) mechanical strength; (f) weight; (g) cost. States that the capacity of a battery is measured in ampere hours at a given rate. Solves problems on efficiency of batteries in terms of ampere-hours and watt-hours.

1.14 1.15

1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24

Solves problems involving batteries in series and in parallel combinations including internal resistance and current in a connected load. Draws a simple charging circuit from a dc supply. Measures the state of charge of a battery before and after carrying out the charging procedure. States the two common types of semi conductor material as germanium and silicon. Explains the formation of Ipl type and Inl type semi conductor materials referring to the doping process. Draws a p-n junction in forward and reverse bias modes and indicates electron flow and conventional current flow in the junction and in the external circuit. Obtains the static characteristic curves for forward and reverse biasing of the pn junction from test results. States the need for rectification of alternating voltages. Explains and draws circuit diagrams to show how rectification of an ac single phase supply is obtained using: one diode; two diodes and centre tapped transformer; and bridge connected diodes. Draws the input and output waveforms for the rectifier circuits in 1.24. Explains the formation of a pnp and npn alloy junction transistor. Draws a circuit diagram showing pnp and npri transistors connected in the common emitter mode Draws and explains a circuit diagram illustrating the use of a transistor as a switch. Draws and explains a circuit diagram illustrating the use of a transistor as an alternating small signal amplifier. Describes the photo-electric effect and its application to photo-diodes. State some marine applications of 1.28 and 1.30.

1.25 1.26 1.27 1.28 1.29 1.30 1.31

Element 2 2. Understands the operation of simple linear dc and ac electrical circuits and solves related problems. Performance Criteria 2.1 2.2 2.3 2.4 2.5 States Ohms Law. Solves problems on 2.1. States Kirchhoffs Current Law. States Kirchhoffs Voltage Law. Describes a series circuit configuration using a variety of components and finds the equivalent resistance.

2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 2.23 2.24 2.25 2.26 2.27 2.28 2.29 2.30

Describes a parallel circuit configuration using a variety of components and finds the equivalent resistance. Solves problems on series/parallel circuits. Solves problems on power and energy in dc resistive circuits. Solves problems using Kirchhoffs laws by application of simultaneous equations (two unknowns only). Explains the principle of the Wheatstone bridge and derives the balance equation. Solves problems related to 2.10. Defines an alternating emf in terms of its maximum value, rms level,-periodic time, frequency "and its time equation. States that e = EMAX sin 2ft volts. Explains that the resultant current will also be sinusoidal and represented by i = lMAX sin 2ft ampers. Solves problems related to 2.13 and 2.14. Draws the wave forms for above and indicates peak value; peak to peak value; periodic time; frequency. Explains terms, mean value, rms value and form factor with reference to a sine wave. Calculates the rms value, mean value and form factor of sinusoidal and non-sinusoidal wave forms. Explains the term phasor quantity. Explains how phasors may be used to represent sinusoidal quantities. Solves graphical problems involving addition and subtraction of ac voltages and currents using phasor method. Sketches the current, voltage and power waveform patterns of a pure: (a) resistor; (b) inductor; (c) capacitor; when connected to a sinusoidal supply. Draws phasor diagrams for pure resistive, inductive and capacitive circuits and distinguishes between in phase, lagging and leading currents. Defines and calculates inductive reactance and capacitive reactance. Constructs and uses phasor "diagrams for R-L, R-C and R-L-C series circuits. Sketches and uses impedance triangles for the series circuits in 2.25. Defines phase angle and active and reactive components. Resolves phasor quantities into active and reactive components eg I cos and I sin . Solves circuit problems using circuit elements connected as in 2.28. Constructs a diagram in terms of active power, apparent power and reactive power.

2.31 2.32 2.33 2.34

Defines power factor as the ratio of active power to apparent power. Solves problems related to 2.30 and 2.31. Measures and notes value of V, I and P in an R-C and R-L series ac circuit. Draws a phasor diagram from the results in 2.33 and calculates the power factor and capacitance/inductance of the circuit.

Element 3 3. Understands the principles of magnetism and electromagnetic induction. Performance Criteria 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 Explains the terms magnetic polarity, magnetic field, magnetic flux, magnetic flux density. States that a current carrying conductor produces a magnetic field. Draws the magnetic field pattern for a straight conductor, loop and a solenoid carrying current. Determines the polarity of fields in 3.3 using corkscrew rule, right-hand gripping rule, end rule as appropriate. Explains the terms magnetomotive force and magnetic field strength. Explains the effect of introducing a magnetic material into a magnetic field. States the units of flux and flux density. Explains the use of magnetic screening. Explains the term reluctance and states the advantages and disadvantages of leaving air gaps in magnetic circuits. States that S = F Explains the terms (a) absolute permeability; (b) permeability of free space; (c) relative permeability. States that B = o r.H and explains that r is not a constant. Draws the B-H curve for a non magnetic material. Draws the B..;H curve for a typical ferromagnetic material. States that different ferromagnetic materials will give different B-H curves. Solves problems on simple non composite magnetic circuits to include the use of graphs. Solves problems on composite magnetic circuits (to include air gap) and the effect of fringing and leakage. States that a current carrying conductor in a magnetic field has a force exerted on it.

3.19 3.20

Determines the direction of the force in 3.18. States that the magnitude of the force is given by F = B I newton and F = aB newton 20 Solves problems related to 3.20 States that the ampere is defined on the basis of the force between two current carrying conductors. States Faraday's law of electromagnetic induction. States Lenz's Law. States that the magnitude of the emf induced in a coil is determined by: (a) the number of turns; (b) the rate of change of flux cutting the coil. Explains that other factors, principally the material of the coil core, also determine the value of induced emf. Solves problems related to 3.25. States that an emf can be self induced in a coil. States that L i volts t Defines the unit of self inductance. States that L = N and L = N I S Solves problems related to 3.29, 3.31. Shows that the energy stored in the magnetic field of a current carrying coil is given by L I joules. States that changing magnetic flux emanating from one circuit can induce an emf in another. States that the effect in 3.34 is called mutual inductance. Defines the unit of mutual inductance. States that the emf of mutual inductance is given by e = M i. and M = k L1L2. t States examples of mutual inductance effect eg transformer, engine ignition coil. Solves problems related to 3.37. States that a conductor moved in and at right angles to a magnetic field will have an emf induced between its ends and determines its direction. States that the magnitude of the emf will be determined by E = B lv volts. Solves problems related to 3.41.

3.21 3.22 3.23 3.24 3.25 3.26 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 3.36 3.37

3.38 3.39 3.40 3.41 3.42

Element 4 4. Understands the principles and applications of dc and ac motors and generators. Performance Criteria 4.1 4.2 4.3 4.4 4.5 4.6 States that: (a) motors convert electrical energy into mechanical energy; (b) generators convert mechanical energy into electrical energy. Explains using simple sketches the action of a single loop dc generator and motor. Describes the function of a commutator. Labels on a given diagram the essential parts of a dc machine. Sketch circuits for shunt, series arid compound wound dc machines. Relates the emf induced in the armature of a dc generator to the expression = 2Z O n P volts. A Solves problems related to 4.6. Solves dc generator circuit problems using V = E -IARA. Obtains the load characteristics of shunt and compound dc generators. Relates the 'back emf' {Eb) induced in the armature of a dc motor to the expression Eb = 2Z O P volts A Solves dc motor circuit problems using V = Eb + IaRa. Explains the need for starting resistance for a dc motor. Explains the method of speed control for a dc motor using variation of armature voltage and field methods. Explains that for a dc machine Eon and TIaO. Solves problems using E

4.7 4.8 4.9 4.10

4.11 4.12 4.13 4.14 4.15

4.16 4.17 4.18 4.19 4.20 4.21

Recognises the power losses which occur in dc machines. Obtains the load characteristics {T/la) of shunt, series and compound dc motors. Explains the basic operation of an ac generator. Labels on a given diagram the essential parts of a 3 phase, ac generator of both salient and cylindrical rotor construction. Explains how to safely synchronise an incoming 3 phase ac generator to live busbars using lamps and/or synchroscope and voltmeters. Obtains the load characteristics of a 3 phase ac generator under various power factor conditions.

4.22 4.23 4.24 4.25 Part B

Explains the basic principle of operation of the 3 phase single cage ac induction motor. Describes with sketches the construction of the 3 phase single cage ac induction motor. Obtains the load characteristic {T/n) of a 3 phase ac single cage induction motor. States typical marine applications for the motors in 4.17 and 4.23 and generators.

Learning Elements 5 6 7 8 9 Electric Circuit Principles Electronic Circuit Principles Generation Distribution Utilisation

Elements and Performance Criteria Element 5 5 Solves dc linear circuit problems under steady and transient conditions.

Performance Criteria 5.1 5.2 Solves steady-state dc circuit problems involving not more than three unknowns using Kirchhoff's laws. Predicts graphically transient voltage and current relationships in simple resistance-inductance (R-L) and resistance-capacitance (R-C) circuits when switched on and off a steady dc supply. States the time constants of simple R-L and R-C circuits as = L and = CR respectively. R States the form of exponential growth and decay formulae applied to R-L and RC circuits. Uses exponential growth and decay formulae to obtain particular values of current or voltage at a given time or vice-versa in simple R-L and R-C circuits.

5.3

5.4 5.6

Element 6 6 Solves dc non-linear circuit problems under steady-state conditions.

Performance Criteria 6.1 States that a non-linear device is one that does not obey Ohm's law.

6.2 6.3 6.4 6.5 6.6 6.7

Shows that a non-linear element may be described by its V/I characteristic in a graphical or mathematical form. Lists typical examples of non-linear devices eg generators, rectifier elements, transistors, thermistors etc. Estimates dc and ac resistances of a non-linear element under given operating conditions. Derives graphically an overall (dynamic) V/I characteristic for a simple dc series or parallel circuit including a non-linear element and a linear resistor. Solves simple dc non-linear circuits mathematically given the V/I law of the non-linear element. Solves simple dc non-linear circuits graphically using load-line technique or dynamic characteristics.

Element 7 7 Understands operation of single-phase and three-phase ac circuits.

Performance Criteria 7.1 Describes using phasor diagrams, voltage and current relationships obtained in pure resistance, pure inductance and pure capacitance circuits when energised from a single phase sinusoidal ac supply. Calculates impedance (Z) of simple R-L-C circuit combinations in series and in parallel. Defines circuit power factor as ratio of active power to apparent power and as cos = R. Z 7.4 7.5 7.6 7.7 7.8 7.9 Solves simple series and parallel ac circuit problems including pf correction. ] Sketches voltage and current phasor diagrams representing simple R-L-C series and parallel circuits. Recognises that voltage and current resonance occurs when series and parallel R-L-C circuits respectively operate at unity power factor. Derives f = 1 as the resonant frequency of a series R-L-C circuit. 2LC

7.2 7.3

Defines active power (P), apparent power (S) and reactive power (Q). Sketches a power triangle (P Q and S) to represent operating conditions in a singlephase circuit.

7.10 Solves single-phase circuit problems using P Q and S quantities. 7.11 Sketches the interconnection of three separate single phases to form 3-phase star and delta connections. 7.12 Sketches, 3-phase voltage and current phasor diagrams to represent balanced star or delta connection.

7.13 Derives relationships VL = 3 Vph for star and IL = 3 Iph for delta balanced connections using phasor diagrams. 7.14 Shows mathematically that total 3-phase power is given as P = 3VL IL cos ; for both star and delta connections. 7.15 Solves 3-phase balanced circuit problems using voltage, current and power relationships. Element 8 8 Understands the operation of junction diodes in rectification circuits.

Performance Criteria 8.1 8.2 8.3 8.4 8.5 8.6 Recognises typical forward and reverse V/I characteristics for Si and Ge diodes. Compares half-wave, bi-phase, and bridge rectification circuits supplied from single and three phase power supplies. Sketches typical dc output waveforms from rectifier circuits in 4.2. Calculates mean dc voltage at output of half and full-wave single-phase circuits given the ac input supply and vice-versa. Describes the action of a simple C-only smoothing circuit in conjunction with a rectifier. Tests complete dc power supply circuits.

Element 9 9 Understands the operation of the Thyristor as a controlled rectifier.

Performance Criteria 9.1 9.2 9.3 9.4 9.5 9.6 9.7 Describes the construction of a thyristor as a 4-layer p-n device with anode, cathode and gate terminals. States bias voltage polarities necessary for "turn-on" of a thyristor. States conditions necessary for thyristor turn-off. Sketches simple circuit diagram of series connected thyristor controlling a dc load from an ac supply (no gate circuitry required). Describes circuit action of 5.4 under variable phase shift gate pulse control and block firing control. Sketches typical load current and voltage in a simple ac driven thyristor controller with variable phase shift gate control. Tests a complete single-phase thyristor power controller.

Element 10 10 Understands the function of a Zener Diode as a dc voltage stabilizer.

Performance Criteria 10.1 10.2 10.3 10.4 10.5 10.6 10.7 Defines voltage stabilisation as the ability of a power supply to maintain its output voltage against changes in loading and input voltage. Describes the action of a p-n junction Zener diode with forward and reverse bias voltages applied. Recognises that a Zener diode must be worked with reverse voltage bias to become a stabilising element. States that a Zener diode is rated in terms of its Zener voltage (VZ) and its power handling ability. Describes the action of a simple voltage stabilising circuit of a Zener diode and current limiting resistor in series across an unregulated dc supply. Calculates values of voltages, currents and powers in a given simple dc stabiliser circuit under changes in supply voltage and loading conditions. Tests a complete dc voltage stabiliser circuit.

Element 11 11 Understands the action of a transistor and its function as a switch and signal amplifier device.

Performance Criteria 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9 Describes the basic construction of p n p and n p n bi-polar transistors. Describes the current distribution in p n p and n p n transistors when the emitter-base junction is forward biased and the collector-base junction is reverse biased. Defines dc current relationships as hFB = Ic and hFE = Ic Ie Ib Sketches the basic common-base, common-emitter and common-collector connections of a transistor. Recognises static transistor characteristics in common-emitter and common-base mode. Describes the "cut-off" condition of a transistor when the base-emitter junction is zero or reverse biased. Describes the "fully-on" (saturated) condition of a transistor when the base-emitter junction is heavily forward biased. Compares cut-off and saturation of a transistor with an ideal electric switch. Describes the action of a simple transistor switching circuit used for alarm and/or control purposes.

11.10

Sketches a practical common-emitter circuit arrangement showing dc bias arrangements, temperature stabilisation resistor and input and output signal connections. Describes the action of a common-emitter circuit as a small-signal amplifier. Draws a load-line onto the static output characteristics of a transistor to predict current gain.

11.11 11.12

Element 12 12 Understands the principles of operation of a dc generator.

Performance Criteria 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 12.10 12.11 12.12 12.13 12.14 12.15 12.16 12.17 12.18 12.19 Reviews basic operation of a dc generator. Derive the emf equation E = 2po.Z n = k o n. A Evaluates generated emf. Describes self excitation and states factors which may prevent it. Estimates generated emf from magnetisation curve and given shunt field resistance. Estimates critical shunt field resistance from a given magnetisation curve. Sketches field and armature circuits for shunt and compound wound machines (long shunt and short shunt). Explain voltage control using shunt field regulator. Describes armature reaction and its effects. Describes commutation, its effect and method of improving commutation eg brush shifting and interpoles. Solves problems involving E, V, Ia, Rf and Ra. Sketches V/I load characteristics of shunt and compound generators (cumulative and differential connections). Estimates voltage regulation from E V. V Lists typical marine applications of generators in 8.7. Calculates series turns required to produce given terminal voltage on load. Describes the connection of a dc compound generator to live busbars and effects of varying excitation. Explains the use of the equalising connection. Describes method of disconnecting a generator from the busbars. Solves load sharing problems graphically and mathematically for shunt and compound generators.

12.20 12.21 12.22 12.23 12.24 12.25

States the reasons for a d.c. generator failing to excite. Describes the methods of exciting d.c. generators that have lost their residual magnetism. Explains the need for preference trips. Describes, with the aid of a schematic diagram, the operation of a preference trip. Explains the need for a reverse current relay. Describes the operation of a reverse current relay.

Element 13 13 Understands the principles of operation of ac generators.

Performance Criteria 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 13.10 13.11 13.12 13.13 13.14 13.15 13.16 13.17 Describes the arrangement of an armature winding to produce a three phase emf. Sketches wave form diagram of three phase voltages. Derives relationship between frequency, poles and speed. Derives emf equation E = 2.22. o .Z.f. Sketches equivalent circuit per phase including Eph, Xs assuming resistance to be negligible. Explains the effect of load and power factor on terminal voltage. Calculates emf given terminal voltage inductive load conditions and winding reactance. Estimates voltage regulation from E-V. V Describes connection of a three phase generator to live busbars, disconnection and shut-down. Explains the effects of operating: (a) governor; (b) field regulator. Solves load sharing problems where information is limited to kW, kVA, kVAr. Describes the construction of salient and cylindrical pole a.c. generators. Appreciate the reason for the 2 types of rotor. Explains why an AVR is required for a.c. generators. Describes the methods of exciting a.c. generators. Describes, with the aid of diagrams, how brushless a.c. generators are excited using: (a) rectifiers; (b) silicon controlled rectifiers (thyristors) . Describes, with the aid of a schematic diagram, the operation of a compounded a.c. generator.

13.18 13.19 13.20 13.21

States the advantages and disadvantages of: (a) the insulated neutral system; (b) the earthed neutral system for marine a.c. generators. Explains the need for a reverse power relay. Describes the operation of a reverse power relay. Explains the need for preference trips.

Element 14 14. Understands typical arrangements of marine dc and ac distribution systems.

Performance Criteria 14.1 14.2 14.3 14.4 Calculates current distribution and load potentials in dc: (a) radial feeders; (b) ring mains: (c) double fed systems using dissimilar voltages. Describes three phase, three wire and four wire systems. Calculates value of the neutral current in a three phase, four wire unbalanced system. Describes the function of the transformer in an ac distribution system.

Element 15 15 Understands the principles of operation of a transformer.

Performance Criteria 15.1 15.2 15.3 15.4 15.5 15.6 15.7 15.8 15.9 15.10 15.11 15.12 15.13 Relates induced emf to rate of change of flux linkages. Derives voltages and currents from turns ratios of single phase transformer. Derives emf equation E = 4.44 f o Z. Sketches phasor diagrams on and off load lag pf only and solves related problems. Sketches three phase connections eg star/delta, star/star etc. using correct terminal markings. Solves problems involving three phase transformers using turns and voltage ratios. Sketches circuit diagram of auto-transformer. Explains principles of operation of auto-transformer. Solves problems on auto-transformers involving voltages, turns and tapping point. Lists losses which occur in transformers. Calculates efficiency of a transformer given load conditions and losses. Explains the need for instrument transformers. Explains the reasons for earthing the secondary winding of instrument transformers.

Element 16 16 Understands the principles of operation of a dc motor. Reviews the basic operation of shunt, series and compound dc motors.

Performance Criteria 16.1 16.2 16.3 16.4 Derives speed equation n = V IaRa ko Explains speed control using shunt field regulator, diverter resistance, tapped field or armature voltage control methods. Derives torque equation T = p o Z a Ia = k o Ia. 2

Sketches torque/armature current, speed/armature current characteristics and derives from these torque/speed curves for shunt, series and compound motors (cumulative only). Solves problems involving changing load, field and/or circuit conditions. Lists the losses which occur in dc motors and generators. Calculates constant losses from no-load input as a motor and hence estimates efficiency of motor or generator under load conditions. Tests a dc motor using Swinburne test and assesses efficiency under stated load conditions.

16.5 16.6 16.7 16.8

Element 17 17 Understands the principles and operation of the three-phase induction motor.

Performance Criteria 17.1 17.2 17.3 17.4 Explains the production of a magnetic field rotating at synchronous speed by a three phase stator winding. Calculates slip given number of poles, frequency and motor speed. Evaluates rotor frequency. Shows that input to rotor equals motor input minus stator losses and that this input equals 2 Tns watts. Calculates rotor output = 2 Tnr watts. Evaluates rotor resistive power loss from difference between 13.4 and 13.5. Calculates motor output = 2TLn. Calculates efficiency from 13.4 to 13.7. Describes the construction of single, double-cage and slip ring motors. Sketches typical torque/slip curves for single, double- cage and slip-ring motors. Describes with the aid of sketches the following starters:

17.5 17.6 17.7 17.8 17.9 17.10 17.11

D.O.L.: 17.12 17.13 17.14 17.15

: slip ring

Explains the reasons why a motor may "single-phase". Describes the effect of a motor "single-phasing". Describes the motor enclosures used in the marine environment. Describes the methods of varying the speed of a.c. induction motors.

Element 18 18 Understands principles of operation of 3-phase synchronous motor.

Performance Criteria 18.1 18.2 18.3 18.4 18.5 Relates synchronous motor to ac generator. Describes pony motor and induction motor starting methods. Describes effects of changing load and excitation. Solves problems of pf improvement type. States marine applications of the synchronous motor.

Element 19 Performance Criteria 19.1 19.2 19.3 Describes with the aid of a sketch, the operation of a fluorescent lighting circuit. Sketches a navigation lighting circuit. Describes, with the aid of sketches, how earth faults are detected for (i) l-phase and (ii) 3-phase supplies.