Rectangular Concrete Tanks

PCA

Revised Fifth Edition

b y Javee dA . M u n shi

P o rtla nC e m e n ts s o c ia tio n 5 0 0N e w J e rsAev e n uNeW 7, t hflo o r d A 5 4 2 0 ldO r c h a Rdo a d O r W a s h in g tDo C2,0 0 0 1 - 2 0 6 6 n S k o k ie , o is6 0 0 7 7 -1 0 8 3 Illin 2 0 2 .4 0 8 .9 4F a x2 0 2 .4 0 8 .0 8 7 7 94 8 4 7 .9 6 6 .6 2 F a x8 4 7 .9 6 6 .9 7 8 1 w w .c e m e n t.o rg 00 w An organization cementcompanies improveand extend of to the uses of portland cem entand concretethroughmarket developm ent, engineering, research,education, and public affairswork.

C o n te n ts
Chapter 1 Introduction Chapter 2 Plate Analysis Results Chapter 3 Tank Analysis Results Chapter 4 Multicell Tanks Chapter 5 Examples Appendix 1-1 2-1 3-1 4-1 5-1

Introduction
Conventionally reinforced (non-prestressed) concrete tanks have been used extensively in municipal and indus trial facilities for several decades. The design of these structures requires that attention be given not only to strength requirements, but to serviceability requirements as well. A properly designed tank must be able to withstand the applied loads without cracks that could cause leakage. The goal of designing and constructing a structurally sound tank that will not leak is achieved by providing the proper amount and distribution of rein forcement, the proper spacing and detailing of construction joints, and the use of quality concrete, placed using proper construction practices. A thorough review of the latest report by ACI Committee 350 entitled Environmental Engineering Concrete Structures [11* is essential in understanding the design of tanks. The document recommends that, unless noted otherwise, the structural design should conform to Building Code Requirements for Structural Concrete (ACI 318) [2]. Therefore, a working knowledge of ACI 318 is also necessary. This publication consists of five chapters and an appendix. The contents of these are as follows:

Chapter1

Introduction

Except for the notations and the definitions, the topics discussed in this chapter are, for the most part, items presented in ACI 350 that are not addressed in ACI 318: Notations and Definitions Design Methods Durability Minimum Reinforcement Loading Conditions Crack Control Formwork Considerations Base Fixity Buoyancy Forces Earthquake Forces Codes, Specifications and Standards References Suggested Literature
-

Chapter2 Plate AnalysisResults

This chapter gives the design coefficients for deflection (Cd), shear (Cs) and moments (Ms, M M,,,) for , plates with different end conditions. Results are provided from finite element analyses of two-dimensional plates subject to out-of-plane loads using SAP9O [19]. Convergence analysis was made to ensure the quality of the results. The slab was assumed to act as a thin plate, for which equations and/or the design coefficients are available in some of the references listed [6-10]. However, since only a limited number of cases are available in such literature, this text was prepared to cover a wider range of loading configurations, end-restraint conditions, and width/height ratios.
*See the end of this chapter for cited references.

Coefficients for individual panels with fixed side edges apply without modification to continuous walls, pro vided there is no rotation about vertical edges. In a square tank, therefore, moment coefficients can be taken directly from the tables in Chapter 2. For a rectangular tank, adjustments must be made to account for redistri bution of bending moments to adjacent walls. The design coefficients for rectangular tanks are given in Chapter 3.

C h a p te r T an kA n alys is esu lts 3 R

-

This chapter gives the design coefficients for deflection (Cd) and moments (Mi, M, M,, and M for tanks ) with different end conditions. The design coefficients are based on finite element analysis of tanks. The design coefficients (M M Mx,,) presented in Chapter 2 for design of plates can also be used for tanks that , have square plan dimensions. For rectangular tanks, the plate analysis results are not applicable since they do not account for moment distribution that will occur between the walls of different stiffnesses. An adjustment must be made similar to the modification of fixed-end moments in a frame analyzed by moment distribution. The shear coef ficient (C 3) given in Chapter 2 for plates may be used for design of rectangular tanks. If the moment distribution method is used, the common side-edge of adjacent panels is first considered artifi cially restrained, so that no rotation can take place about the edge. Fixed-edge moments taken from the results presented in Chapter 2 are usually dissimilar in adjacent panels, and the differences, which correspond to unbal anced moments, tend to rotate the edge. When the artificial restraint is removed, the unbalanced moments will induce additional moments in the panels. Adding the induced and fixed-end moments at the edge gives final moments, which must be identical on both sides of the common edge. Note, however, that moment distribution cannot be applied as easily to continuous tank walls as it can to framed structures, because bending moments must be distributed simultaneously along the entire length of the side edge so that moments become equal at both sides at any point of the edge. Moreover, tanks will develop in-plane axial compression or tension. Effects of the tension force, if significant, should be recognized. If significant compression forces are developed, the reduction in the effective stiffness of the member may also need to be considered.

T C h a p te r M ultice ll a nk s 4
-

This chapter provides information on how to modify single-cell coefficients for use in multicell tank design. An appropriate method based on relative wall stiffnesses is given to compute the design moments in intersecting walls of multi-cell tanks.

C hapter5- E xam p les

A complete design for a wall and the roof slab of a rectangular tank is presented. Two examples that explain the determination of the bending moments for multicell tanks are also provided.

A pp end ix
A design aid that can be used for determining the required reinforcment for a rectangular concrete section subject to a given bending moment is located in the appendix.

N o ta tio n s anD efin ition s d

a w q k
= = =

height of plate or wall. unit weight of soil or water (for example, lbIft3). k wa, pressure at bottom of plate/wall for triangular load distribution (for example, lb/ft2). uniform pressure along height of plate/wall (for example, lb/ft2). k w for coefficient of active or passive pressure, whichever is applicable [3]. For water, active pressure coefficient ka = 1, while for soil ka = (1 sintb)/(l + sin), where of internal friction of soil [3].
-

angle

C5 1 -2

shear coefficient given in tables of Chapter 2 for computation of shear: Shear per unit width C 5 q a.

RectangularTanks

Cd E
t

deflection coefficient given in tables of Chapters 2 and 3 for computation of deflections. Deflection = Cd q a4/1000 D, where D = E t3 / 12(1-!?). modulus of elasticity of concrete (E = w5 33J from ACI 318-95, where w is the unit weight of concrete and is the specified compressive strength of concrete, psi). thickness of plate or wall. Poissons ratio, taken as 0.2 for concrete. Coef.
=

= =

(M M M, M and M ) ,

moment coefficients given in tables of Chapters 2 and 3 for com putation of moments M ,3 M M, M and respectively. , Note that M and coefficients are given in absolute values.

moment per unit width about the x-axis stretching the fibers in the y-direction when the plate or wall is in the x-y plane (see Fig. 1-1). The moment is used to determine steel in the y (vertical) direction of the plate or wall (Fig. 1-1) and is given by: M Coef. =M X qa/1000

moment per unit width about the y-axis stretching the fibers in the x-direction when the plate or wall is in the x-y plane, or in the z-direction when the plate is in the y-z plane (see Fig. 1-1). The moment is used to determine steel in the x or z (horizontal) direction of the plate or wall (Fig. 11) and is given by: M
=

X M Coef. q a2/1000

moment per unit width about the z-axis stretching the fibers in the y-direction when the plate or wall is in the y-z plane (see Fig. 1-1). The moment is used to determine steel in the y (vertical) direction of the plate or wall (Fig. 1-1) and is given by: M Coef. =M
X

qa/1000

M ,

torsion or twisting moments for plate or wall in thex-y and y-z planes, respectively, given by: M M o f. = Ce
=

qa/1000

Coef. X q a2/1000

y z

Platein x-yIane

Figure1-1 Coordinate System for Plates

Introduction

1 -3

The twisting moment such as M may be used to add to the effects of orthogonal moments M and M for the purpose of determining the steel reinforcement when the plate is in the x-y plane. can be similarly used for the plate in the y-z plane. These moments should be considered for safe design wherever their effect is deemed to adversely affect the steel requirement. The Principle of Minimum Resistance [4] may be used for determining the equivalent orthogonal moments in this case. The equivalent orthogonal moments M and M for a plate in x-y plane are computed as , follows: Where positive moments produce tension: M2
=

M +jM3,j

= M

+ M E ,I

However, if either M or M is found to be negative, the negative value of the moment is changed to zero (no steel required) and the other moment is given as follows: M2 >0

ifM t<0,thenM tx=OandM y=My+-f-

M+ Where negative moments produce tension: M _ x My M_ x I M xy M = y-M

fly

M2

>0

However, if either M or M is found to be positive, the positive value of the moment is changed to , zero and the other moment is given as follows: M2

ifM LX.>0,thenMtX=0andM Y=M

<0

ifM ,

>0,thenM 31=0andM =

M2

<0

DesignMethods
Two approaches currently exist for the design of reinforced concrete members: (1) Strength Design, and (2) Allowable Stress Design (referred to in Building Code Requirements for Structural Concrete (ACI 318-95) Appendix A, as the Alternate Design method).

R e c ta n g u la ra n k s T

The Strength Design method became the commonly adopted procedure for conventional buildings following the issuance of the 1963 edition of the ACI Building Code, and constitutes the basic procedure of design in the present ACI Building Code (ACI 318-95) with the Alternate Design method in an appendix (Appendix A). Until recently, the use of strength design for municipal and other facilities was considered inappropriate due to the lack of reliable assessment of crack widths at service loads. The advances in this area of knowledge in the last two decades has led to the acceptance of strength design for municipal liquid retaining structures. The latest ACI Committee 350 report recommends procedures for the use of both Allowable Stress Design and Strength Design for liquid retaining structures. Service state analysis of reinforced concrete structures should include computations of crack widths and their long term effects on the structure in terms of its stability and functional performance. Current methods of reinforced concrete design lead to computations which are, at best, a modified form of elastic analysis of the composite reinforced steellconcrete system. Due to the well-known effects of creep, shrinkage, volume changes, and temperature, all analyses of this type, in terms of computed stresses, are indices of performance of the structure and should not be construed to have any more significance than that. The following discussion describes the alterations in the design methods of ACI 318 provided by ACI 350. Strength DesignThe load combinations to determine the required strength, U , are given in Section 9.2 of ACI 318-95. ACI 350 requires the following two modifications to that section. Modification 1The load factor to be used for lateral liquid pressure, F, is 1.7 rather than 1.4. This value of 1.7 may be overconservative for some tanks, since they are filled to the top only during leak testing or because of accidental overflow. Since leak testing usually occurs only once and since most tanks are equipped with over flow pipes, some designers have considered using the load factor of 1.4 in an attempt to reduce the amount of required steel, which would result in less shrinkage restraint. However, this publication suggests that tank designs meet ACI 350 and, therefore, recommends the use of a load factor of 1.7 with F. Modification 2The members must be designed to meet the required strength, U , under ACI 318-95. ACI 350 requires that the value of U be increased by using a multiplier called the sanitary coefficient. The sanitary coefficient will increase the design loads to provide a more conservative design with less cracking. The in creased required strength is given by: Required strength = Sanitary coefficient X U where the sanitary coefficient equals: 1.3 for flexure 1.65 for direct tension 1.3 for shear beyond that of the capacity provided by the concrete These sanitary exposure coefficients, together with an increase in the conventional load factor for fluids from 1.4 to 1.7, increase all load factors from ACI 318 a total of 30% for flexural reinforcement, 65% for direct tension reinforcement (such as ring tension), and 30% for stirrup or diagonal tension requirements. The strength equations are given as follows: 1 . Flexural Reinforcement Reqd strength bM 1.3 U 1.3 (1 .4MD + 1 .7ML + 1 .7MF)

2. Direct Tension Reinforcement Reqd Strength 1.65 U 1.65 (1.4 7 D 1.7TL + 1.7TF)

Introduction

1 -5

3.

S tir r uReinforcement p
) bV3LI 1.3(V- V

4. Concrete Shear and Compression Reqd Strength> 1.0 U No increase is required in load factors for concrete shear, bond, or compression strength, so that proportioning member depths or thickness will be unchanged. For flexure, the proposed increase in load factors results in a maximum load factor of 1.3 times 1.7=2.21 for normal live and water and earth load and a minimum load factor of 1.3 times 1.4 = 1.82 for all dead load. In conjunction with -factors prescribed in ACT 318, these new load factors result in flexural service load stresses in the reinforcement between 24 and 29 ksi, consistent with allow able stresses for working stress design in the current report by ACI Committee 350. The same limits on bar spacing apply equally well with use of strength design (see ACT 350).

D u rab ility
Durability, which is a concern for practically every type of structure, is of vital importance where environmental structures are concerned. Leakage from a tank can cause a multitude of problems. Loss of a valuable material from leakage will result in direct economic loss. Also, if the stored material is a waste product, in particular hazardous waste, costly cleanup may be required. ACI 350 lists the effects that need to be adequately resisted to satisfy durability requirements. The concrete must be able to withstand the following: Alternate wetting and drying Freezing and thawing cycles Chemical action Exposure to the elements

Durability requirements can be satisfied by providing a properly placed, dense concrete that meets limits on water-cementitious materials ratios placed by the applicable codes and specifications. The designer needs to consider more than just the concrete walls and must appropriately address the details of the entire structure. The joints between adjacent pours must have properly functioning water stops to prevent leakage. These water stops must also be immune to chemical attack from the stored liquid. Any architectural fmishes must be taken into account, so as not to jeopardize the durability of the tank. For instance, tanks that have brick veneer must allow for moisture between the brick and the concrete tank wall to escape, as trapped moisture could lead to premature deterioration of the tank wall. Therefore, before any such finishes are used, the possible detrimental effects must be carefully considered and proper precautions taken. Conditions may arise where the tank walls or water stops are unable to withstand the chemical attack of the liquid being contained. When such conditions exist, the designer needs to make use of a liner to protect the tank walls. In addition to protecting the tank walls, liners can also sometimes make it possible to relax crack control requirements, since leakage through cracks may cease to be an issue.

M in im u m R ein fo rcem en t
The amount, size, and spacing of reinforcing bars has a great effect on the extent of cracking. The reinforcement provided must be sufficient for strength and serviceability, including consideration of temperature and shrinkage effects. The amount of temperature and shrinkage reinforcement is dependent on

R e c ta n g u la ra n ks T

the length between construc tion joints and the yield stress of the reinforcement, as shown in Fig. 1-2. Figure 1-2 is based on the assumption that the wall segment is allowed complete shrinkage movement without being restrained at the ends by adjacent

R e c ta n g u la ra n ks T

sections. The designer should provide proper details to ensure that the joints which are likely to crack are prop. erly leak-proofed. According to ACT 3 5 0 , concrete sections that are 24 in. or thicker can have the minimum temperature and shrinkage reinforcement at each face, based on a 12 in. thickness. The reinforcement should be spaced not greater than 12 in. on center, divided equally between the two surfaces of concrete sections. The reinforcement near the bottom of base slabs in contact with soil may be reduced to 50 percent of the value given in Fig. 1-2. The size of reinforcing bars should be chosen with the realization that cracking can be better controlled by using a larger number of small diameter bars rather than fewer larger diameter bars. The size of reinforcing bars, according to ACI 350, should not, preferably, exceed No. 11. Spacing of reinforcing bars should be limited to a maximum of 12 in., and the minimum concrete cover for reinforcement in the tank wall should be at least 2 in.
0.006 0.005 0.004 O.OO3 0.0028
<

,,.Grade 40 Grade 60

0.002 0.001
/ / /

/ I ,

,1I

I 1 -Minimum .

10

18.5- 223 050

.4

40

50

60

Length betweenshrinkage-dissipating joints in feet

Figure 1-2 Ratio of Shrinkage and Temperature Reinforcement for Concrete Made with ASTM CiSO and C595 Concrete (AC! 350 R-89)

LoadingConditions
A tank must be designed to withstand the loads that it will be subjected to during many years of use. But it is equally important to consider loads during construction. An example of some of the loading conditions that must be considered for a partially buried tank is shown in Fig. 1-3. The tank must be designed and detailed to withstand the forces from each of these loading conditions. The tank may also be subjected to uplift forces from hydrostatic pressure on the bottom of the slab when the tank is empty, as discussed in the Buoyancy Forces section of this chapter. Therefore, it is important for the design engineer to determine all possible loading condi tions on the structure. According to ACI 350, the proper design of a tank will include the full effects of the soil loads and water pressure without taking into account loads acting in directions that minimize the effects of each other.

Intro du ction

1 7
-

1 Condition1 Leakagetest priorto backfiling

4

C o nd ition2 Backfillprior to addingtank cover

Condition3 Tankfull w ith cover in place. esistance p rovid e db y so il is ignored

Figure1-3 PossibleLoadingConditions for a Tank

Crack Control
Crack widths must be minimized in tank walls to prevent leakage and corrosion of reinforcement. A criterion for flexural crack width is provided in AC T 318-95 (Section 10.6.4). This limitation is as follows: zf = J where z quantity limiting distribution of flexural reinforcement. calculated stress in reinforcement at service loads, ksi. thickness of concrete cover measured from extreme tension fiber to center of bar located closest thereto, in. effective tension area of concrete surrounding the flexural tension reinforcement having the same centroid as that reinforcement, divided by the number of bars, sq in.

f
d A

= = =

The determination of d and A are shown in Fig. 1-4 for a single layer of reinforcement (A = 2d b). In ACI 350, the cover is taken equal to 2.0 in. for any cover greater than 2.0 in. Rearranging the above equation, and solving for the maximum bar spacing (b for a given value of z, withf5 being the stress in the bars, gives ) max. spacing (b )
=

2 2xd x

f33

A C T 318-95 does not allow z to exceed 175 kips/in. for interior exposure and 145 kips/in. for exterior exposure. These values of z correspond to crack widths of 0.016 in. and 0.013 in., respectively. A CT 350 has stricter requirements than A CT 318, since cracking is typically of greater consequence in liquid-retaining structures. The limiting value of z specified in ACT 350 is 115 kips/in. (crack width of 0.010 in.). For severe environmental exposures, the quantity z should not exceed 95 kips/in. (crack width of 0.008 in.). Joints in the tank walls will allow dissipation of temperature and shrinkage stresses, thereby reducing cracking. As discussed previously, the amount of temperature and shrinkage reinforcement is a function of the distance between shrinkage-dissipating joints. Therefore, it is prudent to limit the size of concrete placement. Maximum length of wall placed at one time should usually not exceed 60 ft, with 30 ft to 50 ft being more common.

R e ctangulara n k s T

A= 2d0b t = w a llth ic kn e ss

dcl
b

/ /

vertical reinforcem ent

Figure 1-4 Effective Tension Area of Concrete for Calculation of z

Form w ork onsiderations C

Formwork for tank structures is subject to the same considerations as that for other structures, such as proper bracing to maintain position and shape, time of removal, etc. However, there are additional considerations for formwork for tanks. A tank must be a watertight structure. Proper design and detailing may not be enough to reach this goal. Con struction procedures are equally important. One consideration, for example, is that form ties shall have no metal or other material within 1 1 /2 inches from the formed surface. After the forms are removed, the void left from the form ties shall be cone shaped, at least 1 inch in diameter and 1 1/2 inches deep, to allow proper patching. Another consideration is that the individual sections of a tank wall shall be placed continuously to produce a monolithic unit, with a waiting period of 48 hours before casting the adjacent wall. There shall be integral water stops at each joint.

B as eFixity
The restraint condition of the wall at the base is needed to determine the deflection, shears and bending moments for a given loading condition. Base restraint conditions considered in this publication include both hinged and fixed edges. However, in reality, neither of these two extremes may actually exist. It is important that the designer have an understanding of the degree of restraint provided by the reinforcing that extends into the footing from the tank wall. If the designer is unsure of the fixity conditions, both extremes should be investi gated.

B uo y an cy o rces F
Water pressure on the underside of the tank can possibly cause the tank to literally float. This situation may result in cracking of the tank walls and the base slab. It may also cause damage to piping attached to the structure. The lifting force of the water pressure is resisted by the weight of the tank and the weight of soil on top of the base slab overhang. As the force of the water pressure tries to lift the tank, it will engage some of the soil adjacent to the tank. The angle of the soil engaged (see Fig. 1-5) is a function of the type of soil. If the buoyancy force times an appropriate safety factor is in excess of the resisting force, pressure relief valves should be utilized to prevent the buildup of pressures. Even if uplift forces are small, it still may be prudent to place the pressure relief valves in the base slab.

introduction

1 -9

Angle

c i
\
i I I I I ii

W all

Exterior Face of W all

Zn t g i Figure 1-5 Angle of Soil Engagement Due to Uplift

E arthq u ak Fo rce s e
Earthquakes can induce large horizontal and overturning forces in tanks. The tanks should be properly designed and detailed for such forces. Concrete tanks, being typically rigid, are primarily designed to resist the forces due to the hydrodynamic mass of the contained fluid. The deformability of the wall and the interaction of the wall and the fluid are not, typically, considered in design. However, wall deformability may be considered where it is likely to effect the tank design. Reference [14] may be used for this purpose. Hydrodynaniic pressures include both impulsive and convective components. Impulsive pressures are devel oped by accelerations of the tank walls against the mass of the contained liquid. The fluid acts as a mass rigidly attached to the container walls. Convective pressures are produced by oscillations or sloshing of the upper portion of the liquid within the tank. The sloshing fluid acts as if it were an oscillating mass flexibly connected to the walls. ACI Committee 350/350R is currently in the process of developing comprehensive seismic design and detailing standards for liquid-containing structures. The recommendations of the committee are expected to be out by the year 2000. Several references [12-18] are currently available which can be utilized for the seismic design of tanks. The most widely used method for computation of seismic forces on tanks is the one developed by Housner [13,15]. The engineer may use this method along with relevant seismic design and detailing provisions of the applicable codes in the region for the seismic design of tanks. Earthquakes are also likely to produce external earth pressure on the walls of partially or fully buried tanks which should be taken into consideration. However, in case of buried vaults it has been found [17] that seismic pressures do not control design unless the peak ground acceleration exceeds a value of about O.3g, where g is the acceleration due to gravity. This would indicate that forces due to seismically induced earth pressure on buried tanks should not be of major concern in low to moderate seismic zones. Both the reinforcement detailing and the detailing of the joints are critical for ensuring seismic safety and se rviceabilityof tanks. Serviceability consideration is of particular importance in liquid retaining structures in the aftermath of an earthquake [16]. The detailing of joints at the base of the tank requires special attention when movement is allowed in the joint. In case of monolithic joint between the wall and the base slab and between wall and the roof, adequate and proper reinforcement details are necessary to prevent excessive distress at these

10

R ectangular Tanks

locations due to the anticipated stress concentration. Special detailing for joints in case of prestressed concrete circular tanks is given in [11]. Similar detailing would be necessary for nonprestressed rectangular tanks.

Codes, Specifications and Standards

Sizable construction projects are performed using comprehensive sets of detailed drawings in conjunction with specifications. The parts of the specifications regarding construction are compiled by experienced specifiers. However, the specifications alone do not list every requirement. Instead, the project specifications refer to codes, standards and guide specifications of the American Concrete Institute and the American Society of Tes ting Materials, to name a few. These requirements are strictly adhered to during construction, and it is worth while for the reader to review them. The most commonly referenced codes, specifications and standards can be divided into five groups, presented here in Tables 1-1 through 1-5.

Ta ble1 -1 G ene ral e qu ire m e n ts R

AC I 301 ACt 302 AC I 318 ACI 350 Specifications StructuralConcretefor Buildings for Guidefor ConcreteFloorand Slab Construction 8uilding Code Requirements Reinforced for Concrete Environmental Engineering Structures

T a b le 1 -2 F ie ldT e s tin g u id e s n d Standards G a A C I 214 A S T M C 31 ASTM C39 ASTM Cl 43 ASTM Cl 73 A S TM C 231 R ecom m ended Practicefor Evaluation S trengthTest R esults Concrete of of StandardPracticefor M akingand C uringTestSpecim ens the Field in StandardTest M ethodfor C om pressive Strengthof Cylindrical oncreteSpecimens C StandardTestM ethodfor Slum pof PortlandC em entConcrete StandardTestM ethodfor Air Content FreshlyM ixedC oncreteby the Volum etric of Method StandardTest M ethodfor Air Contentof FreshlyM ixedC oncreteby the PressureMethod

Introduction

11

Table1-3 Concrete, em entand Related aterialGuIdesand Standards C M A C I 201 A C I 21 1 ACI 212 A C I 221 ACI 304 ASTM C33 ASTM C94 ASTM C150 ASTM C260 ASTM C309 ASTM C494 ASTM C 6 18 G uideto D urableConcrete S ta n d a rd ra c tic e r SelectingProportions Norm al,H eavyweight M assConcrete P fo for and G uidefor U se of A dm ixtures Concrete in G uidefor U se of N orm alW eightA ggregate Concrete in G uidefor M easuring, ixing,Transporting PlacingConcrete M and StandardSpecifications C oncrete for Aggregates StandardSpecifications Ready-M ixed for Concrete StandardSpecifications PortlandCement for StandardSpecifications Air-Entraining for Adm ixtures Concrete for StandardSpecifications LiquidM em brane-Form ing pounds CuringConcrete for Com for Standard Specifications C hem ical for Adm ixtures Concrete for S tandardS pecification Fly A sh and R aw or C alcinedN aturalP ozzolan U se as a for for M ineralAdm ixturein PortlandCem entConcrete

Table 1-4 ReinforcIng Steel Standards ASTM A615 S tandardSpecification D eform ed P lainBillet-S teel for and Barsfor C oncreteReinforcement ASTM A 6 16 StandardSpecification R ail-Steel eform ed for D and PlainBars for C oncreteReinforcement for Deform ed and PlainBarsfor ConcreteReinforcement ASTM A 6 17 StandardSpecification Axle-Steel for Bar ASTM A706 StandardSpecification Low-AlloySteelD eform ed for ConcreteReinforcement for SteelBars for ConcreteReinforcement ASTM A767 Standard Specification Galvanized for R SteelBars ASTMA775 StandardSpecification Epoxy-C oated einforcing

Table1-5 ConcretePlacementGuides ACI 305 AC I 306 ACI 308 ACI 309 Hot W eatherConcreting Cold WeatherConcreting StandardPracticefor CuringConcrete Guidefor Consolidtion Concrete of

I 12
-

R e c ta n g u la ra n k s T

R efe ren c es
1. 2. 3. ACI Committee 350, Environmental Engineering Concrete Structures (ACI 350R-89), American Con crete Institute, Detroit, 1995. ACI Committee 318, Building Code Requirements for Structural Concrete (ACI 318-95), American Con crete Institute, Farmington Hills, MI, 1995. Bowles, J.E., Foundation Analysis and Design, 4th Ed., McGraw-Hill, Inc., NV 1988.

4. Gupta, A.K., and Sen, S., Design of Flexural Reinforcement in Concrete Slabs, Journal of the Structura Division, ASCE, Vol. 103, ST4, 1977, PP. 793-804. 5. 6. 7. 8. 9. 10. 11. 12. Hengst, R., Concrete Watertight Structures and Hazardous Liquid Containment, ASCE Press, American Society of Civil Engineers, NY, 1994. Javemicky, J., Tablesfor the Analysis ofPlates, Slabs andDiaphragms Based on Elastic Theoty, Macdonald and Evans, Germany, 1979, 474 pages. Moody, W.T., Moments and Reactions for Rectangular Plates, United States Department of the Interior, Bureau of Reclamation, Denver, 1960, 74 pages. Sarkar, R.K., Slab DesignElastic Method (Plates), Verlag UNI-Drnek, 8 Munich 40, West Germany, 1975. Szilard, R., Theoiy and Analysis of PlatesClassical and Numerical Methods, Civil Engg., and Engg. Mechanics Series, Prentice Hall, Inc., NJ, 1974. Timoshenko, S., Theory of Plates and Shells, McGraw-Hill Book Co., New York, 1940, 492 pages. AWW A D115-95 Standard for Circular Prestressed Concrete Water Tanks with Circumferential Tendons, American Water Works Association, 6666 West Quincy Ave., Denver, CO, 80235, 1995. Ballantyne, D.B., Pinkham, C.W., and Weinberger, L.W., Seismic Induced Loads on Sanitary Facilities, ASCE Specialty Conference on Lifeline Earthquake Engineering, American Society of Civil Engineers, NY, 1981. Haroun, M.A., and Housner, G.W., Seismic Design of Liquid Storage Tanks, Journal of the Technical Councils of the ASCE, Proceedings of the American Society of Civil Engineers, ASCE, Vol. 107, No. TC 1 , 1994.,pp. 191-207. Haroun, M.A., Stress Analysis of Rectangular Walls Under Seismically Induced Hydrodynamic Loads, Bulletin of the Seismological Society ofAmerica, Vol. 74, No. 3, 1984, pp. 103 1-1041. Housner, G.W., The Dynamic Behavior of Water Tanks, Bulletin of the Seismological Society ofAmerica, Vol. 53, No. 2, 1963, pp. 38 1-387. ilceda, S., Seismic Design of Concrete Structures Based on Serviceability after Earthquakes, ACI Spe cial Publication SP1J 7 , Long-Term Serviceability of Concrete Structures, 1989, pp. 45-54. Miller, C.A., and Costantino, C.J., Seismic Induced Earth Pressures in Buried Vaults, P VP-Vol. 271, Natural Hazard Phenomena and Mitigation, American Society of Mechanical Engineers (ASME), 1994, pp. 3-11. 1 13

13.

14. 15. 16. 17.

Introduction

18.

U .S. Nuclear Regulatory Commission (formerlyAtomic Energy Commission), Nuclear Reactors and Earth quakes, Chapter 6, Appendix F, Washington D.C., National Technical Information Service, Division of TechnicalInformation, TID-7024,1963.
SAP9O A Series of Computer Programs for the Finite Element Analysis of Structures, Computers and Structures, Inc., Berkeley, CA, 1992.

19.

Suggested Literature 1.
ACI Committee 209, Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures, Designing for Creep and Shrinkage in Concrete Structures, SP-76, American Concrete Institute, Detroit, 1982, pp. 193-300. Gogate, A.B., Structural Design of Reinforced Concrete Sanitary StructuresPast, Present, and Future, Concrete International, Vol. 3, No. 4, April 1981, p. 24. Gogate, A.B., Structural Design Considerations for Settling Tanks and Similar Structures, ACI Journal Proceedings, Vol. 65, No. 12, December 1968, pp. 1017-1020. Gray, WS., Reinforced Concrete Reservoirs and Tanks, Concrete Publications, Ltd., London, Second Edition, 1942, 166 pages. Rice, P . F.,Structural Design of Concrete Sanitary Structures, Concrete International, Vol. 6, No. 10, October 1984, p. 14. Wood, R. H., Joints in Sanitary Engineering Structures, Concrete International, Vol. 3, No. 4, April 1981, p. 53.

2. 3. 4. 5. 6.

1 14
-

R e c ta n g u la ra n k s T

Introduction
Conventionally reinforced (non-prestressed) concrete tanks have been used extensively in municipal and indus trial facilities for several decades. The design of these structures requires that attention be given not only to strength requirements, but to serviceability requirements as well. A properly designed tank must be able to withstand the applied loads without cracks that could cause leakage. The goal of designing and constructing a structurally sound tank that will not leak is achieved by providing the proper amount and distribution of rein forcement, the proper spacing and detailing of construction joints, and the use of quality concrete, placed using proper construction practices. A thorough review of the latest report by ACI Committee 350 entitled Environmental Engineering Concrete Structures [1] * is essential in understanding the design of tanks. The document recommends that, unless noted otherwise, the structural design should conform to Building Code Requirements for Structural Concrete (ACI 318) [2]. Therefore, a working knowledge of ACI 318 is also necessary. This publication consists of five chapters and an appendix. The contents of these are as follows:

Chapter1

Introduction

Except for the notations and the definitions, the topics discussed in this chapter are, for the most part, items presented in ACI 350 that are not addressed in ACI 318: Notations and Definitions Design Methods Durability Minimum Reinforcement Loading Conditions Crack Control Formwork Considerations Base Fixity Buoyancy Forces Earthquake Forces Codes, Specifications and Standards References Suggested Literature
-

Chapter2 Plate AnalysisResults

This chapter gives the design coefficients for deflection (Cd), shear (Cs) and moments (Mr, M M for , ,) plates with different end conditions. Results are provided from finite element analyses of two-dimensional plates subject to out-of-plane loads using SAP9O [19]. Convergence analysis was made to ensure the quality of the results. The slab was assumed to act as a thin plate, for which equations and/or the design coefficients are available in some of the references listed [6-101. However, since only a limited number of cases are available in such literature, this text was prepared to cover a wider range of loading configurations, end-restraint conditions, and width/height ratios.
*See the end of this chapter for cited references.

Coefficients for individual panels with fixed side edges apply without modification to continuous walls, pro vided there is no rotation about vertical edges. In a square tank, therefore, moment coefficients can be taken directly from the tables in Chapter 2. For a rectangular tank, adjustments must be made to account for redistr ibution of bending moments to adjacent walls. The design coefficients for rectangular tanks are given in Chapter3.

C h a p te r T an kA na ly sis es u lts 3 R
-

This chapter gives the design coefficients for deflection (Cd) and moments (Mi, M Mi,, and M for tanks ) , different end conditions. The design coefficients are based on finite element analysis of tanks. The with design coefficients (Mr, M, M presented in Chapter 2 for design of plates can also be used for tanks that ,) have square plan dimensions. For rectangular tanks, the plate analysis results are not applicable since they do not account for moment distribution that will occur between the walls of different stiffnesses. An adjustment must be made similar to the modification of fixed-end moments in a frame analyzed by moment distribution. The shear coef ficient (C 3) given in Chapter 2 for plates may be used for design of rectangular tanks. If the moment distribution method is used, the common side-edge of adjacent panels is first considered artifi cially restrained, so that no rotation can take place about the edge. Fixed-edge moments taken from the results presented in Chapter 2 are usually dissimilar in adjacent panels, and the differences, which correspond to unbal anced moments, tend to rotate the edge. When the artificial restraint is removed, the unbalanced moments will induce additional moments in the panels. Adding the induced and fixed-end moments at the edge gives final moments, which must be identical on both sides of the common edge. Note, however, that moment distribution cannot be applied as easily to continuous tank walls as it can to framed structures, because bending moments must be distributed simultaneously along the entire length of the side edge so that moments become equal at both sides at any point of the edge. Moreover, tanks will develop in-plane axial compression or tension. Effects of the tension force, if significant, should be recognized. T I significant compression forces are developed, the reduction in the effective stiffness of the member may also need to be considered.

C ha p te r M ultice ll an k s 4 T
-

This chapter provides information on how to modify single-cell coefficients for use in multicell tank design. An appropriate method based on relative wall stiffnesses is given to compute the design moments in intersecting walls of multi-cell tanks.

C hapter5- E x am p le s
A complete design for a wall and the roof slab of a rectangular tank is presented. Two examples that explain the determination of the bending moments for multicell tanks are also provided.

A ppendix
A design aid that can be used for determining the required reinforcment for a rectangular concrete section subject to a given bending moment is located in the appendix.

N o tatio ns nd D e finitio n s a
a w q k
= = = = =

height of plate or wall. unit weight of soil or water (for example, lb/ft3). k W a,pressure at bottom of plate/wall for triangular load distribution (for example, lb/ft2). k w for uniform pressure along height of plate/wall (for example, lb/ft2). coefficient of active or passive pressure, whichever is applicable [3]. For water, active pressure coefficient ka = 1 , while for soil ka = (1 sin4)/(1 + sin eb),where = angle of internal friction of soil [3].
-

C3

shear coefficient given in tables of Chapter 2 for computation of shear: Shear per unit width C3 q a.

Rectangular anks T