General EarthWork Procedure

Document:
GENERAL EARTH WORK PROCEDURE

UNIT ISSUING: APPROVED BY: Project Manager
Date Revision: Page: 1 of 21 Revision: 0
PROCEDURE FOR GENERAL EARTH WORK
Procedure for General Earth Work
Document:

TABLE OF CONTENTS
Page 1. General & Scope .. 1.1. Scope 1.2. Code & Standard 2. Description of Work Procedure 2.1. Preceding Work 2.2. Preparation 2.3. Protection 2.4. Control of Water 2.5. Hauling, Excavation, Backfill, and Compaction 2.6. Open Drainage Structure 2.7. Fill & Embankments 2.8. Site Restoration ... . . .. .. . .. 4 3 7 8 9 10 19 19 21 ..................... 3
Document:

1. GENERAL 1.1. Scope This description prescribes the procedures for the following: 1.1.1. The excavation, fill, and embankment construction procedure to achieve the Site finished grades indicated on plans or otherwise required by the IFC Drawing. 1.1.2. The excavation procedure for construction of footings, foundations, and other structures and the placement and compaction of backfill to restore finished grade around completed structures. 1.1.3. The excavation, bedding, backfilling, and compaction procedure for installing underground piping, culverts, and associated appurtenances. 1.1.4. The disposal of unsatisfactory and surplus excavated materials. 1.1.5. The furnishing, placement, and compaction of selected backfill material when required. 1.1.6. The furnishing of borrow, when sufficient quantity of satisfactory backfill materials is not available from on site sources. 1.1.7. The control of surface runoff and groundwater as necessary for the safe and efficient execution of the Work. 1.2. Code and Standard General earthwork code & standards shall be as per client/contract specification, except as amended this procedure by the client or otherwise shown on the approved design drawing.
2. DESCRIPTION OF WORK PROCEDURE 2.1. Preceding Work 2.1.1. Clearing and Grubbing 2.1.1.1. General y Avoid damage to the Site and to existing facilities, trees, peat, and shrubs designated to remain.
Document:

y
Protect benchmarks, baseline monuments, property corners, and other temporary or permanent survey markers in the vicinity of the Work from destruction or disturbance.
Within the area to be cleared, properly relocate survey markers that interfere with the Work, or witness the markers and then restore them after completing the Work.
Before starting clearing operations, erect protective barriers around trees, shrubs, and other facilities designated to remain. Erect barriers at or outside of the tree or shrub drip line. Do not use the area within protective barriers for traffic, storage, or any other purpose. After clearing and grubbing work is complete, properly remove and dispose of protective barriers.
2.1.1.2. Survey Work y Preliminary survey location of road, piping corridor, gathering station, and other facilities shall be done using Total Station tools. y Surveying shall be started from recommended GPS benchmarks and one other reference benchmark. From these two benchmarks, activity shall be continued to surveying of road and corridor center line with minimum two survey points at both ends for every center line. y After obtain two reference points, activity shall be continued to the cutting line and stake out works. Output of preliminary survey is a general situation and preliminary stake out for guidance on detail survey. y Move existing or master of benchmarks to the project site and built up the local benchmarks or benchmark monument permanently. Local benchmark will be checked periodically to ensure the accuracy of elevations and coordinates. Benchmarks shall be protected from object disturbances. y At least one local benchmark monument shall be provided for a quadrant. Additional benchmark monument shall be provided if one monument is not adequate.
Document:

y
Theodolite and levelling shall be employed in surveying coordinates and elevations. Closed-polygon per quadrant method shall be used in surveying coordinates.
Distance of stake out shall be 165 feet (50 m) up to 330 feet (100 m), identified by bamboo or wooden dolken, and marked by red colour for easy identification. Temporary or permanent marker shall be protected from destruction or disturbance.
All instruments shall be calibrated before used.
2.1.1.3. Clearing & Grubbing y Clearing shall be done on all areas, which is included borrow pit, road, corridor, and gathering station before starting the filling work. y Clearing includes removal and proper disposal of trees, bushes, stumps, rubbish, and other vegetation resting on or protruding through the ground surface area to be cleared, without removing its roots. Clearing shall be performed at all back fill area. y All garbage material shall be stored at adjacent or destination area and shall not be burned. y Stripping at borrow pit area includes cutting of topsoil up to maximum 1-foot depth. Topsoil shall be stored around borrow pit area. y Grubbing includes removal and disposal of roots, stumps, bushes and other obstruction materials, which protruding through the ground surface. Grubbing may includes cutting of topsoil up to 4-inches (10-cm) depth if required. Grubbing shall be performed at strong surface only. Grubbing at peat area shall not be performed. y Especially for gathering station & other plant areas, depth of excavation shall follow the approval engineering drawing. y Dozer D6/D7 shall be used in clearing and grubbing works.
Document:

y
Disposal materials shall be stored at adjacent location around 165 feet (50 m) from original location.
Trees with minimum 4" diameter shall be selected from disposal materials and shall be used as corduroy material. These selected trees shall be stored in dry area before the installation.
Other disposal materials such as topsoil, debris, and roots shall be spread around the location without disposing them outside the project area. This location shall be replanted.
2.1.1.4. Smoothing of Terrain y Remove from the project Site and dispose of debris resulting from clearing and grubbing operations. y After clearing and grubbing have been completed, eliminate stump holes, depressions, ridges, and other irregular surface features by grading and backfilling to achieve a surface suitable for subsequent construction operations. Shape the resulting surface for positive drainage of surface runoff. y Areas to be excavated immediately after clearing and grubbing is completed, need not to be smoothed. 2.1.2. Topsoil Removal and Stockpiling 2.1.2.1. Topsoil is generally representative of agriculturally productive soil. Topsoil shall be free from subsoil and objectionable material that would hinder plant growth or maintenance and shall not contain more than 5% by volume of stones larger than 1-inch. 2.1.2.2. Remove materials only to such depth that it meets the definition of topsoil. Strip and stockpile removed topsoil in areas to be excavated separately from other excavated materials. Protect topsoil stockpiles from contamination during progress of the work until their materials have been used in finish operations. Conserve acceptable topsoil from the Site sufficiently to cover areas requiring planting.
Document:

2.2. Preparation 2.2.1. Preliminary Site Examination Prior the excavation, thoroughly examine the area to be excavated to verify the locations of features indicated on the drawings and to ascertain the existence and location of any underground structure or other item not shown that might interfere with the new structure or pipe installation. Notify client of any obstructions that will prevent accomplishment of the Work. Take protective measurement to prevent existing facilities within the work area that are not designated to be removed from being damaged by the Work. 2.2.2. Fills and Embankments Where the structure or pipeline is to be installed in an area of fill or embankment, verify that such work has been completed to an elevation at least 2-feet above the bottom of the structure to be installed or at least 3-feet above the top of the pipeline to be installed. No concrete base/slabs and trenches shall be placed on area of fill or embankment when the settlement processes still exist unless they are adequately supported on piles. 2.2.3. Construction Layout Unless otherwise stipulated elsewhere in the Contract documents, the Work covered by this specification includes the performance of all calculations, and the setting of all mark and stakes necessary to ensure that the Work conforms to the required lines, grades, and dimensions. Related such layout to the coordinate grid system, elevation datum, and related survey control monuments and benchmarks identified on the drawings or elsewhere in the Contract documents.. 2.2.4. Excavation Safety Plan for and assemble materials and equipment required to stabilize excavation sidewalls as necessary to ensure the safety of personnel working in the excavation and to protect existing facilities and structures in the vicinity of the Work from damage. The systems, methods, and techniques used shall meet or exceed all
Document:

applicable requirements, and regulations. Barriers and warning devices shall be placed around all excavations, especially where excavations are unattended, to indicate a hazard exists, in the immediate vicinity. 2.3. Protection 2.3.1. Slope Stabilization 2.3.1.1. Stabilize the sides of excavations as necessary to prevent slope failure or any other earth movement that might injure personnel, or damage existing buildings, structures, or other facilities in the vicinity of the Work. Earth retainers, such as shoring and sheet piling, shall be installed where required. The stabilization method employed shall comply with the requirements and regulations. 2.3.1.2. Carefully remove such systems in order to prevent subsidence or other soil movement that might damage existing or newly constructed structures or other facilities. 2.3.2. Working at Existing or Complete Utilities Carefully move machinery and equipment over existing or newly installed pipes and utilities during construction so as not to damage completed work. For work immediately adjacent to, or excavation exposing an existing utility or other structure, use manual or light equipment excavating techniques. Do not use power driven equipment to excavate closer than 2-feet from any existing utilities or structures. Support uncovered pipes and other existing work affected by the excavation until they are properly supported by backfill. 2.3.3. Working at Structures and Surfaces Protect newly backfilled areas and adjacent structures, slopes, or grades from damage. Repair and re-establish damaged grades and slopes. Protect existing streams, ditches, and other storm water facilities from silt accumulation and erosion.
Document:

2.4. Control of Water 2.4.1. General Prevent or control water flow into excavations, or water accumulation in excavations, to ensure that the bottoms and sides of excavations remain firm and stable throughout construction operations. General sequence of the work shall be started by normalize the existing canal or excavating the new canal. 2.4.2. Surface Water Run Off Plan and conduct excavation operations so as to minimize the disruption of storm water drainage in the vicinity of the Work. Provide diversion ditches, dikes, and other suitable measures to control and direct runoff around and away from the excavation. Protect the sides of excavations from erosion and sloughing caused by storm water runoff. Promptly remove storm water accumulations in excavations. The systems and equipment for controlling surface water shall be of sufficient capacity to accommodate the runoff rate expected from the 2-years (50 percent annual chance) rainfall event, with no significant disruption of the construction schedule, or damage to existing features or facilities in the vicinity of the Work. Run-off water at borrow pit area shall be managed by open ditch at every 164 feet x 164 feet minimum area. Borrow pit area shall be sloped 10% minimum and run-off water shall be drained through open ditch to existing canal. Dimension of canal shall be determined on site. 2.4.3. Groundwater When the bottom of the excavation must be carried to an elevation below the groundwater piezometric surface, or to such proximity to the piezometric surface that the excavation bottom will become soft due to its being saturated by groundwater, take measures to lower the piezometric surface sufficiently to maintain the stability of the excavation bottom. Design the groundwater control system using accepted professional methods of design and engineering consistent with the best modern practice. The system shall include trenches and sumps with pumps, well points, and such other equipment, appurtenances, and related earthwork necessary to achieve the
Document:

groundwater control needs of the Work. Carefully design and operate the system to avoid damage to existing structures and other facilities in the vicinity of the Work. 2.4.4. Disposal of Removed Water Convey water removed by the water control systems to an existing storm water drainage facility that has sufficient capacity to accommodate the flow rates involved without damage. Secure permits or other approvals required from authorities having jurisdiction for such storm water discharge. 2.4.5. System Removal After completing construction operations needing water control, remove materials, equipment, and other facilities used for that purpose, and clean up and restore affected areas as required. 2.5. Hauling, Excavation, Backfill, and Compaction 2.5.1. General Remove soil, rock, and other materials as necessary to achieve the finished grades, sub grades, or other limits of excavation indicated. Use satisfactory materials resulting from excavation work in the construction of fills and embankments, and for the replacement of removed unsuitable materials. After the excavation to the required Finish grade is completed, re-compact materials that are to remain but have been loosened or otherwise disturbed by the excavation operations, to a firm, stable condition, and to a density equal to or greater than the surrounding undisturbed material 2.5.2. Hauling Dump Truck with adequate capacity & number shall be used for hauling dirt materials. Each Dump Truck group shall be supported by excavator, dozer, and compactor at project site. If hauling distance less than 1 km using Scrapper or wheel loader shall be considered for hauling dirt materials. Dump truck shall be maintained periodically in maximum 3 months usage. Before starting the work, driver or mechanic shall perform daily equipment check to ensure the ability of equipment. Provide the required parking
Document:

area of dump truck. Fuel shall be supplied by fuel truck and stored in the temporary tank at parking area. Other earth moving equipment such as dozer, excavator, compactor, and grader shall be parked in adjacent to the job site. Fuel shall be supplied to this location by fuel truck. Access roads route of hauling material from borrow pit area or stockpile area to the project site shall be proposed and explained in the Journey Management Plan (JMP) and periodically maintain the access roads at project site only. 2.5.3. Stockpiling and Disposal of Materials Stockpile excavated satisfactory materials that are surplus to the quantity needed for construction of required fills and embankments, or for replacement of unsuitable. Stockpiles shall be neatly shaped and free draining, with sides sloped at 4 horizontal to 1 vertical or flatter. Dispose of excavated materials that are unsatisfactory for use as fill or backfill or are surplus to that needed for backfilling, in a safe and proper manner off the project Site or in areas of the project Site designated for that purpose. 2.5.4. Rock Excavation Remove rock encountered in areas requiring excavation using mechanical methods (such as ripping, wedging, or impacting) to reduce the rock to manageable sized fragments. Except as otherwise shown, required, or specified, excavate rock to a depth of no less than 12-inches below the indicated finished grade. Backfill undercut areas with satisfactory materials placed and compacted in accordance with the requirements for fills and embankments. In areas to be paved, remove rock to a depth of no less than 3-inches below the pavement sub grade surface. The remaining rock surface shall be free of projecting ribs or points, and shaped so that positive drainage of the surface is provided and no water will be pocketed at any point. Grout crevices in the surface with lean concrete. Backfill undercut areas with satisfactory material, placed and compacted in accordance with the requirements for fills and embankments. 2.5.5. Excavation for Shallow Foundation
Document:

2.5.5.1. Excavate the surface ground down to at least 3-feet depth below the natural ground surface. 2.5.5.2. Remove any lose or soft pocked of soil or organic material and replace with structural fill and shall be compacted to 95% of maximum dry density modified proctor test unless otherwise stipulated elsewhere in specification herein. 2.5.5.3. Re-compact the exposed surface to 95% of maximum dry density modified proctor test unless otherwise stipulated elsewhere in specification herein. Recompaction shall reach a depth of 10-inches thickness preferably by putting structural bedding and shall be in free draining saturated condition before placing the footing. 2.5.6. Compaction and Moisture Control 2.5.6.1. Compact satisfactory backfill material to a uniform dry density of no less than 92% of Modified Proctor Density unless otherwise stipulated elsewhere in specification herein. 2.5.6.2. The top 12-inches of sub grade beneath structurally loaded areas such as slab and foundations shall be compacted not to less than 95% of Modified Proctor Density. 2.5.6.3. Compact each layer to a firm, stable condition using vibratory or impact type compaction equipment suitable for the material and lift thickness and operated in accordance with manufacturers instruction. 2.5.6.4. Adjust the moisture content as necessary to achieve a condition suitable for compaction. For cohesive materials, the moisture content at the time of compaction shall be within 2 percentage points of optimum. 2.5.6.5. When water must be added, distribute it uniformly over the surface of the layer, and thoroughly incorporate it into the soil to achieve a uniform distribution of moisture throughout the material. When the moisture content is
Document:

excessive, defer compaction until the material has dried to suitable moisture content. 2.5.6.6. The Sand-Cone Method may be used to determine the in-place density and unit weight of any soil that can be excavated to a stable condition with hand tools. The use of this test method is generally limited to soil in an unsaturated condition without appreciable amounts of rock or coarse materials more than 1.5 in (38mm) in diameter. This method is not recommended for soils that are soft or in a moisture condition. 2.5.6.7. In area of unsuitable sub grade with low bearing strength such as peat or organic soils, a bridging fill approximately 0.75 to 1.0 meters may be placed with no compaction criteria with client approval. 2.5.7. Excavation, Backfill, and Compaction for Structures Base 2.5.7.1. General Excavation pits for constructing cast-in-place concrete foundations, footings, and other structures to permit the placement of each monolithic element of the structure to the full width and length required with a full horizontal bed. If the excavation sidewalls are to be used to form the sides of the structure, take special care during excavation to secure a true surface conforming to the lines and dimensions indicated on the plans for the structure. Corners and edges of the excavation shall be true and square, not rounded or undercut 2.5.7.2. Foundation Material Other than Rock When the bottom of the foundation is to rest on an excavated surface other than rock, take special care to avoid disturbing the virgin soil at the bottom of the excavation, and to protect the soil from the changes in moisture content. To accomplish this, do not excavate the final 6-inches of material until just before the structure is to be placed. When the bottom of the excavation must be exposed for an extended period of time, during which time inclement weather may damage it, lower the bottom of the excavation approximately 2-inches below the indicated bottom of the
Document:

structure, and backfill the over excavated area with lean concrete. If the bottom of the excavation is not firm and stable, notify client immediately so that appropriate corrective measure may be developed and implemented. 2.5.7.3. Rock Foundation Material. When the bottom of the structure is to rest on rock or other unyielding material, clean the bearing surface of loose material, and cut to a firm, level bed that is stepped, keyed, or serrated. 2.5.7.4. Backfill and Compaction y As soon as practical after completing construction of the related structure, including expiration of the specified minimum curing period for cast-inplace concrete, backfill the excavation to restore the required finished grade. Backfill by placing and compacting satisfactory backfill material or select granular backfill material, when required, in uniform horizontal layers of no greater than 6-inches loose thickness. y Insofar as possible, place and compact backfill symmetrically about the structure to avoid the development of unbalanced earth pressure loads on the structure. y Do not place backfill around new cast-in-place concrete structures until the concrete has cured for at least 3-days; or, when the backfill will result in the development of unbalanced earth pressure loads on the structure, do not start backfilling until the concrete has cured for at least 7-days or compressive strength test indicated the concrete has achieved more than 80 percent of its specified compressive strength. y Step excavation side slope with each layer of backfill to avoid the development of unnecessary loads against the structure caused by backfill wedging between the structure and the excavation sidewalls. 2.5.8. Excavation, Backfill, and Compaction for Underground Piping 2.5.8.1. General
Document:

Carefully excavate trenches to the minimum depths and widths necessary for installing the pipe line and associated appurtenances in accordance with the requirements of this specification, and the lines and grades indicated on the plans or elsewhere in the Contract documents. In the pipe embedment zone, the trench sidewalls shall be as nearly vertical as practical. From the top of the pipe embedment zone to the surface, the trench sidewalls shall be either sloped sufficiently to prevent sloughing or cave-in, or shall be properly supported. Stockpile excavated materials in an orderly manner a sufficient distance from the trench sidewalls to avoid endangering the stability of the bank. 2.5.8.2. Unstable Natural Grade When soft, yielding, or otherwise unstable natural soil conditions are encountered at the required trench bottom elevation, over excavate the trench to a depth of no less than 12-inches below the required pipe bottom elevation, and backfill with granular bedding material. If conditions are so severe that over excavating and backfilling will not achieve a stable condition, notify clent immediately so that appropriate corrective measures may be identified. No underground facilities/utilities shall be placed or embedded in area of fill or embankment when the settlement processes still exist unless they are adequately supported on piles. 2.5.8.3. Unyielding Natural Grade Whenever rock, stone, masonry, or other hard, unyielding material is encountered at or above the required trench bottom elevation, remove it to provide a clearance of no less than 6-inches below and on each side of pipes and associated fittings, valves, and other appurtenances. Backfill the over excavated area with granular bedding material. 2.5.8.4. Previous Excavations In the event that the trench passes over a sewer or through any other previous excavation, carefully compact the bottom of the trench to a density equal to or
Document:

greater than that of the native soil adjacent to the previous excavation. Perform this compaction carefully to avoid damaging the previously installed facility. 2.5.8.5. Excavation for Appurtenances y Excavation for pre-cast manholes, catch basins, drainage inlets, and other similar structures shall be of sufficient size to permit proper placement of the structures in their intended positions, and to permit proper placement and compaction of backfill around the structures after their placement. For cast-in-place appurtenances, excavation shall be of sufficient size to permit placement and removal of necessary formwork. y When concrete is to be placed against the bottom or sides of an excavation, take care not to disturb the native soils that the concrete bears against. Excavate to final line and grade just before the concrete or masonry is to be placed. Remove loose or unstable materials. Clean rock of loose material and other debris, and cut to a firm and stable surface that is either level, stepped, or serrated; remove loose or deteriorated rock and thin strata. 2.5.8.6. Bedding After excavation reaches the required trench bottom elevation and any unsatisfactory sub grade conditions are corrected as specified, prepare the bottom of the trench for placement of the pipe by spreading in the trench a layer of loose granular bedding material to attain a level just above the required grade of the outside of the bottom of the pipe. Carefully shape the surface of this layer of loose material to ensure that uniform and continuous support is provided to the bottom quadrant of each pipe section along its entire length. In the prepared trench bottom, excavate small depressions (bell holes) of the minimum size necessary to allow removing the pipe handling slings, to allow assembly of pipe joints, and to avoid the development of bearing loads on the pipe bells or flanges.
Document:

2.5.8.7. Initial Backfill Place and compact initial backfill from the spring line of the pipe to the top of the pipe embedment zone in uniform horizontal lift of not over 6- inches loose thickness. Bring up the level of backfill uniformly on opposite sides of the pipe along the full length of each pipe section. Take care not to damage the pipe or any protective coating it may have. 2.5.8.8. Final Backfill Place and compact satisfactory backfill material in 8-inches maximum loose thickness lifts to restore the required finished surface grade. During final backfill for plastic or other non-ferrous pipelines, install plastic marking tape above the pipeline at a depth of 1-feet to 2-feet below the required finished grade. 2.5.8.9. Compaction Except in areas of load bearing sub grade, compact final backfill composed of satisfactory materials from the original trenching to a density equal to or greater than that of the existing undisturbed material immediately adjacent to the trench. Where the excavated material is unsatisfactory for use as backfill and, therefore, imported materials are used, compact the backfill to no less than 92% of Modified Proctor Density. 2.5.9. Excavation, Backfill, and Compaction for Roads 2.5.9.1. Earthwork includes excavation, fill and removal of unusable materials (such as vegetation, topsoil, and any other soft soil layer), diversion of surface runoff and temporary shoring when necessary. The level of site fill shall be above the highest flood level that is defined to be equal to the elevation of well pad area. 2.5.9.2. Road sub grade shall be established by cut or fill to the required level as shown on construction drawings. Sub grade level shall be properly shaped to the required profile by motor graders, and shall be rolled and compacted to
Document:

design requirement. Compaction requirement is not less than 95% of Modified Proctor Density. 2.5.9.3. In area of unsuitable sub grade with low bearing strength such as peat or organic soils, a bridging fill approximately 0.75 to 1.0 meters may be placed with no compaction criteria with client approval. 2.5.10. Excavation for canals 2.5.10.1. Site preparation works consist of clearing and grubbing, setting out the canal center line in accordance with the construction drawing and establishing benchmark and grade staking as necessary to carry out construction. 2.5.10.2. Earthwork includes excavation, fill and removal of unusable materials (such as vegetation, topsoil, and any other soft soil layer), diversion of surface run-off and temporary shoring when necessary. 2.5.10.3. Adjust canal center line, if necessary to avoid existing facility, as long as it does not change energy line and wet area of canal. Cutting work shall use excavator with suitable requirements so the excellent work will be performed, dredging equipment shall not be used. 2.5.10.4. Finishing work for canal walls can be done by using excavator or manual workman. 2.5.10.5. Excavated material shall be stored at both sides of canal, with maximum embankment up to 3-feet (1 m). Slope of embankment shall be 1 depth : 2 width. 2.5.10.6. Use soil reinforcement such as geo textile, riprap etc. for the canal embankment protection if necessary. 2.5.10.7. Minimum slope of canal shall be 1-foot depth by 1-foot width. If slope is not indicated on the design drawing, dimension of slope shall be justified on field.
Document:

2.5.10.8. Canal re-shaping is required to recover the capacity back to its original design capacity. Re-shaping canal principally covers activities as follows: y y y y Cutting work a heap in the middle of canal. Re shaping bottom and wall of canal. Repair canal dikes. Widening canal at some location referred to design drawing. Considering that reshaping work at main canal will encounter high obstacles due to the width of canal, it is recommended to use mechanical digging equipment. 2.6. Open Drainage structure Construct new and modified open drainage structure such as: ditches and channels to conform to the lines, grades, and cross sections indicated on the plans or otherwise required by the Contract documents. Trim and dress roots, slumps, rock, and other foreign materials exposed by the work to conform to the required surface. Do not over-excavate. Backfill to grade any excessive excavation using either satisfactory material thoroughly compacted to the density required for fills and embankments or place stone or cobble to form an erosion resistant ditch lining. If the soil bearing capacity is bad, soil improvement shall be done on drainage structure position to eliminate or reducing settlements. 2.7. Fills and Embankments 2.7.1. General 2.7.1.1. Construct fills and embankments by placing and compacting satisfactory materials in successive, uniform, horizontal lifts of no greater than 8- inches loose thickness. Compact each lift to the specified density before placing materials for the overlying lift. 2.7.1.2. Where the required finished grade has a slope steeper than 1 vertical to 8 horizontal, overbuild the slope by no less than 2-feet (measured horizontally) and trim back to finished grade after compaction.
Document:

2.7.2. Embankment Foundation 2.7.2.1. Before placing the first layer of materials, scarify the surface of areas on which fill is to be placed to a depth of no less than 6 inches, and then compact it. 2.7.2.2. Where the existing ground surface on which the fill or embankment is to be constructed has a slope steeper than 1 vertical to 8 horizontal, benches the surface so that each lift can be placed and compacted horizontally. Benching shall be of sufficient width to permit the safe and effective operation of placing and compacting equipment. Begin each horizontal cut at the intersection of the original ground surface and the vertical slides of the previous cut. Re-compact materials cut out for benching in conjunction with the compaction of the new fill materials. 2.7.2.3. Where the fill or embankment is to be placed on an inundated area or on low swampy ground that will not support the weight of the hauling equipment, construct the first lift by dumping successive loads of satisfactory materials in a uniformly distributed layer, of a thickness not greater than that necessary to support the hauling equipment while placing materials for the subsequent lift. Compact the top of this special first lift to a firm and stable condition. However, it need not be compacted to the specified density, provided it is overlaid by at least 2 lifts that are placed and compacted as required. If the conditions are such that 2 full lifts cannot be properly placed over the special lift, notify client so appropriate corrective measures may be developed and implemented. 2.7.3. Large Rocks and Boulders Rocks and boulders exceeding the maximum size allowed in satisfactory fill material may be incorporated into deep fills and embankments subject to the following size and depth limitations: Depth Below Finished Grade (Feet) Maximum Size Allowable
Document:

(Inches) 3 5 6 Over 5 12 Carefully place oversize rocks and boulders incorporated into fills and embankments following this provision so that no voids are created. 2.8. Site Restoration 2.8.1. General After completion of backfill placement and compaction, restore or replace shrubbery, turf, fences, and other features, surfaces, and structures disturbed during the work except as otherwise indicated. Return restored features and facilities to a condition equal or superior to that which existed before the work began. 2.8.2. Finish Grading At the completion of all construction work, the Site shall be graded to provide for the runoff of surface drainage without trapping or pounding water. Trim and finish-grade the surface of areas involved in work covered by this specification. The resulting surface shall be reasonably smooth and free of ruts, ridges, depressions, and other significant irregularities. Leave areas designated to be grassed in a condition suitable for subsequent top soiling, and seeding operations. 2.8.3. Clean up Remove off the Site and properly dispose of surplus piping materials, soils, temporary structures, and other debris resulting from the work. Leave the site in a neat and clean condition, ready to receive topsoil, seeding, or whatever final surface treatment is indicated.

General EarthWork Procedure

Uploaded by

Copyright:

Available Formats

General EarthWork Procedure

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

General EarthWork Procedure

Uploaded by

Copyright:

Available Formats

Document:

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 1 of 21 Revision: 0

PROCEDURE FOR GENERAL EARTH WORK

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 2 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 3 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 4 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 5 of 21 Revision: 0

All instruments shall be calibrated before used.

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 6 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 7 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 8 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 9 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 10 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 11 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 12 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 13 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 14 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 15 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 16 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 17 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 18 of 21 Revision: 0

Procedure for General Earth Work

GENERAL EARTH WORK PROCEDURE

Date Revision: Page: 19 of 21 Revision: 0

Procedure for General Earth Work